MAINTENANCE TRAINING

CONTENT
IP CAMERA
TROUBLESHOOTING
CONTENTS

IP CAMERA
IP CAMERA
Product introduction
Upgrade firmware by serial port/RS-232
Hardware introduction
Troubleshooting
PRODUCT PRESENTATION
UPGRADE FIRMWARE
TOOLS

PC
HARDWARE INTRODUCTION DS-2CD2T43G0-I8

DSP BOARD ARCHITECTURE

HARDWARE INTRODUCTION Module introduction

UD5 JP3 DS10

UP1 XT1
UP5 UP3 UP6 US8 UP2 UT1 J7
UP4

BAT1
U10 JP2 UV1 U2 U3
UM1
U11 U28 Y1
U8
U1 UP7
JP1

JD1 UN1
UF1
HARDWARE INTRODUCTION Function Chip Description

LOCATION CHIP CHIP FUNCTION

U1 DSP, used for image processing and interface control
UM1 DDR, temporary storage for data
JD1 Slot for TF card
U8 Power convert chip, Pin 8 input 3.3V ,Pin 1 output 1.2V_DVDD
U11 Power convert chip, Pin 1 input 3.3V ,Pin 5 output 2.8V_AVDD
U10 Power convert chip, Pin 1 input 3.3V ,Pin 5 output 1.8V_OVDD
UP5 Power convert chip, Pin 2 input 5V ,Pin 3 output 1.5V
UP3 Power convert chip, Pin 2 input 5V ,Pin 3 output 1.1V
UD5 ICR driver chip
UP1 Power convert chip, Pin 1 input 5V ,Pin 5 output LM3380_3.3V(UP2/UP4)
HARDWARE INTRODUCTION Function Chip Description

LOCATION CHIP CHIP FUNCTION

DS10 Diode, protection for DC 12V module
US8 IR LED driver chip
UP2 (LM3380MFX) power management chip,provide enable power to function chip
UT1 Encryption chip, Storage device encryption information
XT1 Crystal for encryption chip,3.57MHz
UV1 Power convert chip, Pin 2 input 12V ,Pin 3 output 5V
UP7 Power convert chip,Pin 2 input 5V ,Pin 3 output 3.3V
U2 Bus buffer/line driver, IC,SN74LVC1G17DCKR,SC70-5
U3 Voltage –level translator, IC,PCA9306DP1,125,SSOP-8
Y1 Clock crystal,32.768KHz,Crystal for clock module
UD1 Power convert chip ,convert 5V to 3318_SD
UD2 Power convert chip ,convert 5V to 3.3V_SD
HARDWARE INTRODUCTION Module introduction

UM1

X1 U1

UF1

DSP MODULE
U1:DSP chip, used for image processing and interface control

X1:Main crystal,24MHz,Provide working clock to the main control chip

UM1:DDR, temporary storage for data

UF1:Flash chip，use to storage to the DSP Uboot system,（ramdisk），core，application and config file；
HARDWARE INTRODUCTION Module introduction

TN2
UN1
JP1

NETWORK MODULE
UN1:Network module main chip, 3.3V power supply

TN2:Process and amplify network signal , network transformer

JP1:network interface，connect to power and network cables

HARDWARE INTRODUCTION Module introduction

CLOCK MODULE
Y1:Clock crystal,32.768KHz,Crystal for clock module
XT1
US8 UT1
BAT1:Clock battery
UD5
BAT1
J7
Encryption MODULE
JP2
Y1 UT1:Encryption chip, Storage device encryption information

XT1:Crystal for encryption chip,3.57MHz

UD2 UD1

JD1
SD CARD MODULE
JD1:SD card slot

UD2:Power convert chip ,convert 5V to 3318_SD

UD1:Power convert chip ,convert 5V to 3.3V_SD

ICR MODULE LED DRIVER MODULE

J7:ICR interface,connect to ICR JP2:IR LED interface
UD5:ICR driver chip US8:LED driver chip
 HARDWARE INTRODUCTION Module introduction

POWER MODULE
UP5:5V-1.5V
UP1
UP3:5V-1.1V UP5 UP3 UP6 UP2
UP1:5V-LM3380_3.3V UP4

UP6:LM3380_3.3V-1.8V
U10 UV1
UP4:LM3380_3.3V-1.1V
U11
U11:3.3V-2.8V U8
UP7
U10:3.3V-1.8V

U8:3.3V-1.2V

UV1:12V-5V

UP7:5V-3.3V

UP2:power management chip , provide enable power to function chip

HARDWARE INTRODUCTION Power Board

JP2
T1 US3
TVS7 TVS6 DS8 TVS5 TVS4
C327
PT1
DS1
US2 QS2 TN2
F1 L1
UV2 UV1 C328
US1 JP1
 HARDWARE INTRODUCTION Function Chip Description

LOCATION CHIP CHIP FUNCTION

C327 Component for POE module, MLCC,10nF,X7R,2KV,10%,T1.6mm,1812
T1 Power transformer, E13031/DXDZ-BK63379, DC12V,1.08A,100KHz,SMT,10P
US3 Optocoupler,LTV-357T-TP1-A,SMT-4
DS8 DC 12V input protection,Schottky diodes,SK34,SMB
L1 Common mode Choke(L-FIL-CM8001R-SM), Filter electromagnetic interference in
power modules
TVS4/TVS5 Network signal protections , TVS,WS03DLC-B,SOD-323
TN2 Process and amplify network signal,network transformer
 HARDWARE INTRODUCTION Function Chip Description

LOCATION CHIP CHIP FUNCTION

US1 PoE Controller(2376H), PD detection, classification and transmission status management
QS2 MOSFET for POE module, to cut the PWM wave
US2 PWM Controller(2845B)
DS1 POE input protection, TVS,5.0SMDJ58A,SMC
UV1/UV2 Rectifier bridge for POE module, 420V,0.8A,MBS-4
F1 Fuse, overload protection
PT1 DC 12V input protection, TVS,SP500B20,20V,SMB
TVS6/TVS7 POE input protections, TVS,BV-SMBJ58C2H,two-way,58V,SMB
HARDWARE INTRODUCTION
POE module principle diagram
HARDWARE INTRODUCTION POE ModuleWorking Principle Diagram

Input MOSFET Cut Transform 12V

POE TRANSFORMER Output
86242 OUTPUT

Output Feedback
PD Detection
Control

Affect
2376H 2845B Optocoupler
 TROUBLESHOOTING POE Power

1. Measure the protection Tube RG impedance first. If it is short or the RG impedance is 100-200
(lower), means the protection tube is broken. The damage of the protection tube will directly affect
the output voltage of the rectifier bridge（ HD02 ） to 0V or very low; remove the protection
tube and measure the output voltage of rectifier bridge（ HD02 ）Whether the voltage is DC
48-57V;
2. POE test point is output voltage of rectifier bridge (HD02) ，if rectifier bridge (HD02) output
DC48-57V，the means POE control chip has been detect PD and power on success
3. Test 6-pin of 2845B chip,review the PWM waveform output,if out put abnormal,please replace
the 2845B chip；
4. If output PWM waveform is normally, Please check whether the MOSFET(86242/4490/24N15)
is turned on and off with the PWM waveform conversion, abnormal please replace the MOSFET
5. If MOSFET is working normally，please view transformer waveform;
 TROUBLESHOOTING DC Power

1.Check DC12V input protection module;

2.Then measure the input and output pins of each power conversion chip;
3. If the input pin voltage is abnormal, please check the previous circuit; if the output pin
voltage is abnormal, please check the enable pin of power chip (it is also possible that the
power conversion chip is broken) ；
POWER-12V DS9
12V
F1 SK34

2 1 12V0

1
CP31 CS50
PT3 CS49 10nF/ CP32
10nF nF
25V 10nF/
25V
2

Prevent surge, release to housing

 TROUBLESHOOTING Network

1. Is RJ45 interface damaged？replace the power and network cable

2. Check serial log and we can also use “getIp”commands check network status
3. Network module（25MHz crystal/network transformer/PHY chip）

LAN Cable Power Mainboard

Board
 TROUBLESHOOTING Booting abnormal

1.Connect with secureCRT/Putty to get serial log print normally;

2. Measure the input and output pins of each power conversion chip;(12V/5V/3.3V/1.8V…)
3. Check the smallest system module;(24MHz/Flash/DSP/DDR)

Power Firmware Mainboard

TROUBLESHOOTING Image

Image
problem

Image No video
abnormal

software ICR Sensor Firmware U2/U3 Sensor Power

chip chip chip
THANKS！