KATO SR 700

Jenis Pesawat Angkat : Rough Terrain Crane

Tipe : KATO SR 700 L
Pabrik Pembuat : Kato
Tempat Pembuatan : Jepang
Tahun : 2017
Tenaga Penggerak : Motor Diesel
Kapasitas : 70 ton
Dimensi (p x l x t) : 12,59 m x 2,99 m x 3,68 m
Berat : 39.750 kg
Panjang Boom : 44,5 m + 13,2 m jib
Serial Number : 6210314
Format Laporan/Mobile Crane/MTU-2020 Rev: 00 Halaman | 2
 ROUGH TERRAIN CRANE
【SPECIFICATION】
■CRANE Specification ■CARRIER Specification
Maximum lifting capacity 70ton×2.5m Maximum traveling speed 49km/h
Boom length 10.0m ― 44.5m (6 section) Gradeability (tan θ) 60% (computed at G.V.W. = 39,750kg)
Fly jib length 8.3m－13.2m (2 section, offset 7°― 60°) Minimum turning radius 11.2m (2 wheel steer)
(center of extreme outer tire) 6.44m (4 wheel steer)
Maximum rated lifting 45.5m (Boom)
height 58.6m (jib) ●Engine
Main Model Mitsubishi 6D24-TLE2A
Hoisting 160m / min. (at 5th layer)
winch
line speed 4 cycle, 6 cylinders, water cooled, direct injection turbo-charged
Auxiliary Type
(winch up) 150m / min. (at 4th layer) diesel engine with intercooling
winch
Piston displacement 11.945L
Main (Parts of line; 16) : 10m / min. (at 5th layer)
Hoisting hook winch Max. power 257kW at 2,200min-1
speed Max. torque 1,275N･m at 1,500min-1
(winch up) Auxiliary (
Parts of line; 1) : 150m / min. (at 4th layer)
winch Fuel due to KATO's recommendation only
Boom derricking angle 0°― 84° ●Equipment and structure
Boom derricking time 66sec / (0°― 84°) Drive system 4×4
Boom extending speed 135sec (10.0m ― 44.5m) Engine mounted 3 elements
Torque converter
Slewing speed 1.8min -1
1 stage (with lock up clutch)
Tail slewing radius 3,550mm Remote mounted full automatic 6 forward & 2 reverse speed with
Transmission
transfer differencial
●Equipment and structure
Number of speeds 6 forward & 2 reverse speed
Box-shaped, 6-section hydraulically terescopic type
Boom type (Boom section 2 / 3, 4 / 5 / 6 simultaneously operated) Front Planetary, drive/steer type
Axles
2 sections (2nd section of hydraulically terescopic type) Rear Planetary, drive/steer type
Jib type (offset angles 7°― 60°) Front & Hydro-pneumatic suspension
Suspension
Boom extension/ Rear Hydraulic locking device with suspension cylinder
Three hydrauric cylinders and wire ropes used together
retraction equipment Service Air-over hydraulic disk brake on 4 wheels
Boom derricking/lowering Two hydraulic cylinders of direct acting type with pressure- brake (front and rear independent circuit)
equipment compensated flow control valve Parking Spring applied, electrically air released parking brake mounted on
Brake system
Driven by axial plunger type hoisting motor through planetary gear brake front axle, internal expanding type
Winch system
reduction. Controlled independently by respective operating lever. Auxiliary
Main & Auxiliary winches Exhaust brake, Hydraulic retarder
Equipped with automatic brake. brake
Slewing equipment Ball bearing type Full hydraulic power steering
Hydraulic H-beam type Steering Completely independent front and rear steering
Type (with float and vertical cylinder in single unit) (with automatic rear wheel steering lock system)

7,600mm (Fully extended) Front 505 / 95 R25 183E ROAD

Tire size
7,200mm (Intermediately extended) Rear 505 / 95 R25 183E ROAD
Outriggers Fuel tank capacity 300 L
Extension 6,500mm (Intermediately extended)
width 5,400mm (Intermediately extended) Batteries (12V－150AH)×2

4,300mm (Intermediately extended) ●Safety devices

2,690mm (Fully retracted) Emergency steering device,
Rear wheel steering lock system (automatic),
Main Mis-shifting prevention system, Brake fluid leak warning device,
Diameter: 18mm×Length: 240m
Wire rope for winch Service brake lock, Suspension lock, Engine overspeed alarm,
hoisting Auxiliary Radiator coolant level warning device,
Diameter: 18mm×Length: 125m Air filter service warning device
winch
●Hydraulic equipment ●Standard equipment
Oil pump 4 pumps, plunger type Centralized lubricating system, Bypass oil filter
Hoisting
Axial plunger type
●Optional equipments
Hydraulic motor
Yellow rev. light, Rear view camera, Side view camera
motor Slewing
motor
Axial plunger type
■GENERAL Dimensions
Control valve Double acting with integral check and relief valves Overall length 12,590mm
Cylinder Double acting type Overall width 2,990mm
Oil reservoir capacity 740L Overall height 3,680mm
●Safety devices Wheel base 5,300mm
ACS (Automatic Crane Stopper with Voice alarm), Front 2,410mm
Slewing automatic stop system, Boom raise / lower dampening function, Treads
Rear 2,410mm
Boom extension / retraction dampening function, Outrigger status detector,
Boom derricking / telescoping holding valve, Overhoist prevention device, Passenger capacity One person
Drum lock device (on aux. winch), Winch holding valve, Automatic winch brake,
Gross
Winch drum roller, Hydraulic safety valves, Outrigger lock pins, approx. 39,750kg
weight
Slewing lock, Joystick control safety stop system,
Hydraulic oil temperature warning device, Hydraulic oil return filter warning device Gross vehicle Front
approx. 19,850kg
mass weight
●Standard equipment
Rear
Hydraulic oil cooler,Working light (on boom, table and cab), approx. 19,900kg
weight
Winch drum turning indication device, Hook for 34 ton, Hook for 5ton
● Stow the hooks in place before traveling.
●Operator's cab ● Before you use this machine, read the precautions in the instruction manual thoroughly to
All steel welded construction, 1 person, Rubber mounted, operate it correctly.
Adjustable steering wheel, Adjustable seat, Seat belt, ● KATO products and specifications are subject to improvements and changes without notice.
Front windscreen wiper & washer (2 speed wiper),
Roof window wiper & washer, Cigarette lighter, Ashtray, Floor mat
●Optional equipment
Winch view camera, Hook for 70 / 48 ton, Slewing warning buzzer,
Winch over unwinding device, Cab heater, Cab cooler, Fan,
AM/FM Radio, Fire extinguisher, ACS outside indicator

62133000
1
 ■RATED LIFTING CAPACITY
10.0m ― 44.5m Boom
(Unit : Metric ton) (Unit : Metric ton)

(7.6m) (7.2m) (6.5m)

Working Working
radius (m) Outriggers fully extended (7.6m) (over side and over rear) radius (m) Outriggers intermediately extended (7.2m) (over side) Outriggers intermediately extended (6.5m) (over side)
10.0m 16.9m 23.8m 30.7m 37.6m 41.5m 44.5m 10.0m 16.9m 23.8m 30.7m 37.6m 41.5m 44.5m 10.0m 16.9m 23.8m 30.7m 37.6m 41.5m 44.5m
Boom Boom Boom Boom Boom Boom Boom Boom Boom Boom Boom Boom Boom Boom Boom Boom Boom Boom Boom Boom Boom
2.5 70.00* 32.00 23.00 12.50 2.5 48.00 32.00 23.00 12.50 48.00 32.00 23.00 12.50
3.0 61.00* 32.00 23.00 12.50 3.0 48.00 32.00 23.00 12.50 48.00 32.00 23.00 12.50
3.5 55.00* 32.00 23.00 12.50 12.00 3.5 48.00 32.00 23.00 12.50 12.00 46.00 32.00 23.00 12.50 12.00
4.0 49.20* 32.00 23.00 12.50 12.00 10.00 4.0 46.00 32.00 23.00 12.50 12.00 10.00 42.00 32.00 23.00 12.50 12.00 10.00
4.5 44.10 32.00 23.00 12.50 12.00 10.00 8.00 4.5 42.00 32.00 23.00 12.50 12.00 10.00 8.00 38.00 32.00 23.00 12.50 12.00 10.00 8.00
5.0 39.50 32.00 23.00 12.50 12.00 10.00 8.00 5.0 38.50 32.00 23.00 12.50 12.00 10.00 8.00 34.50 32.00 23.00 12.50 12.00 10.00 8.00
5.5 35.70 32.00 23.00 12.50 12.00 10.00 8.00 5.5 35.00 32.00 23.00 12.50 12.00 10.00 8.00 31.50 32.00 23.00 12.50 12.00 10.00 8.00
6.0 32.50 30.50 22.00 12.50 12.00 10.00 8.00 6.0 32.00 30.50 22.00 12.50 12.00 10.00 8.00 29.00 30.50 22.00 12.50 12.00 10.00 8.00
6.5 29.50 28.50 20.60 12.50 12.00 10.00 8.00 6.5 29.50 28.50 20.60 12.50 12.00 10.00 8.00 25.00 25.80 20.60 12.50 12.00 10.00 8.00
7.0 26.80 26.00 19.30 12.50 12.00 10.00 8.00 7.0 26.80 26.00 19.30 12.50 12.00 10.00 8.00 21.50 21.80 19.30 12.50 12.00 10.00 8.00
7.5 24.00 18.20 12.50 12.00 10.00 8.00 7.5 23.10 18.20 12.50 12.00 10.00 8.00 18.80 18.20 12.50 12.00 10.00 8.00
8.0 22.00 17.20 12.50 12.00 10.00 8.00 8.0 20.50 17.20 12.50 12.00 10.00 8.00 16.40 16.20 12.50 12.00 10.00 8.00
9.0 17.50 15.40 12.50 12.00 10.00 8.00 9.0 16.00 15.40 12.50 12.00 10.00 8.00 12.90 12.70 12.50 12.00 10.00 8.00
10.0 14.00 13.80 12.50 10.90 10.00 8.00 10.0 12.70 12.40 12.50 10.90 10.00 8.00 10.30 10.00 11.25 10.90 10.00 8.00
11.0 11.40 11.20 11.30 10.00 9.20 8.00 11.0 10.30 10.10 11.10 10.00 9.20 8.00 8.40 8.10 9.30 9.80 9.20 8.00
12.0 9.40 9.20 10.30 9.20 8.40 8.00 12.0 8.50 8.25 9.25 9.20 8.40 8.00 6.85 6.60 7.70 8.40 8.40 8.00
13.0 7.90 7.65 8.70 8.40 7.80 7.30 13.0 7.10 6.85 7.80 8.40 7.80 7.30 5.65 5.40 6.45 7.10 7.20 7.30
14.0 6.40 7.40 7.80 7.20 6.80 14.0 5.70 6.65 7.25 7.20 6.80 4.45 5.45 6.05 6.35 6.50
15.0 5.35 6.35 7.00 6.60 6.30 15.0 4.75 5.65 6.30 6.55 6.30 3.60 4.60 5.20 5.45 5.60
16.0 4.50 5.45 6.10 6.20 5.80 16.0 3.95 4.85 5.45 5.70 5.80 2.90 3.90 4.50 4.75 4.90
17.0 3.80 4.75 5.30 5.55 5.40 17.0 3.30 4.15 4.75 5.00 5.15 2.35 3.30 3.85 4.10 4.25
18.0 3.15 4.10 4.65 4.90 5.00 18.0 2.70 3.55 4.15 4.40 4.55 1.85 2.75 3.35 3.55 3.70
19.0 2.60 3.55 4.10 4.35 4.50 19.0 2.20 3.05 3.60 3.85 4.00 1.40 2.30 2.85 3.10 3.25
20.0 2.15 3.05 3.60 3.85 4.00 20.0 1.75 2.60 3.15 3.40 3.50 1.00 1.90 2.45 2.70 2.80
21.0 2.60 3.15 3.40 3.55 21.0 2.20 2.75 2.95 3.10 1.55 2.10 2.30 2.45
22.0 2.25 2.75 3.00 3.15 22.0 1.85 2.40 2.60 2.75 1.25 1.75 2.00 2.10
24.0 1.60 2.10 2.30 2.45 24.0 1.25 1.75 1.95 2.10 0.70 1.20 1.45 1.55
26.0 1.05 1.55 1.75 1.90 26.0 0.75 1.25 1.45 1.60 0.75 0.95 1.10
28.0 1.10 1.30 1.45 28.0 0.85 1.05 1.15 0.60 0.70
30.0 0.75 0.95 1.05 30.0 0.65 0.80
32.0 0.60 0.70 31.0 0.65
33.0 0.55 Critical ─ ─ ─ ─ 35° 38° 41° ─ ─ ─ 25° 40° 43° 47°
Critical boom angle
─ ─ ─ ─ 28° 33° 37°
boom angle Standard for 48 ton for 34 ton for 48 ton for 34 ton
Standard for 70*/48 ton hook
for 34 ton
hook Hook mass 470kg 330kg 470kg 330kg
Hook mass 530*/470kg 330kg Parts of line 10 7 5 4 4 4 4 10 7 5 4 4 4 4
Parts of line 16*/10 7 5 4 4 4 4

(Unit : Metric ton) (Unit : Metric ton)

Outriggers extended (over front)
(5.4m) (4.3m) (2.69m) Working
radius (m) 10.0m 16.9m 23.8m 30.7m 37.6m 41.5m 44.5m
Boom Boom Boom Boom Boom Boom Boom
Working Outriggers completely retracted
2.5 70.00* 32.00 23.00 12.50
radius (m) Outriggers intermediately extended (5.4m) (over side) Outriggers intermediately extended (4.3m) (over side) (blocked on vartical cylinders)
(over side) 3.0 61.00* 32.00 23.00 12.50
3.5 55.00* 32.00 23.00 12.50 12.00
10.0m 16.9m 23.8m 30.7m 37.6m 41.5m 44.5m 10.0m 16.9m 23.8m 30.7m 37.6m 41.5m 44.5m 10.0m 16.9m 23.8m
4.0 49.20* 32.00 23.00 12.50 12.00 10.00
Boom Boom Boom Boom Boom Boom Boom Boom Boom Boom Boom Boom Boom Boom Boom Boom Boom
4.5 44.10 32.00 23.00 12.50 12.00 10.00 8.00
2.5 48.00 32.00 23.00 12.50 38.00 30.00 23.00 12.50 20.00 15.00 12.00
5.0 39.50 32.00 23.00 12.50 12.00 10.00 8.00
3.0 48.00 32.00 23.00 12.50 38.00 30.00 23.00 12.50 20.00 15.00 12.00
5.5 35.70 32.00 23.00 12.50 12.00 10.00 8.00
3.5 46.00 32.00 23.00 12.50 12.00 38.00 30.00 23.00 12.50 12.00 18.00 15.00 12.00
6.0 32.50 30.50 22.00 12.50 12.00 10.00 8.00
4.0 42.00 32.00 23.00 12.50 12.00 10.00 31.00 29.60 23.00 12.50 12.00 10.00 14.00 13.70 12.00
6.5 29.50 28.50 20.60 12.50 12.00 10.00 8.00
4.5 38.00 32.00 23.00 12.50 12.00 10.00 8.00 24.00 24.30 20.80 12.50 12.00 10.00 8.00 11.30 11.00 9.90
7.0 26.80 26.00 19.30 12.50 12.00 10.00 8.00
5.0 32.20 30.60 23.00 12.50 12.00 10.00 8.00 20.00 19.40 17.60 12.50 12.00 10.00 8.00 9.30 9.00 8.30
7.5 24.00 18.20 12.50 12.00 10.00 8.00
5.5 25.90 25.20 22.40 12.50 12.00 10.00 8.00 16.50 16.00 15.10 12.50 12.00 10.00 8.00 7.80 7.40 7.00
8.0 22.00 17.20 12.50 12.00 10.00 8.00
6.0 21.50 20.90 19.30 12.50 12.00 10.00 8.00 13.90 13.40 13.00 12.50 12.00 10.00 8.00 6.60 6.50 5.90
9.0 19.00 15.40 12.50 12.00 10.00 8.00
6.5 18.20 17.60 16.90 12.50 12.00 10.00 8.00 11.90 11.40 11.30 11.60 11.50 10.00 8.00 5.60 5.20 5.00
10.0 16.00 13.90 12.50 10.90 10.00 8.00
7.0 15.70 15.10 14.80 12.50 12.00 10.00 8.00 10.40 9.80 9.70 10.40 10.35 10.00 8.00 4.80 4.40 4.20
11.0 13.20 12.20 11.30 10.00 9.20 8.00
7.5 13.10 12.90 12.50 12.00 10.00 8.00 8.60 8.40 9.30 9.30 9.20 8.00 3.70 3.50
12.0 11.00 10.70 10.30 9.20 8.40 8.00
8.0 11.50 11.30 12.10 11.90 10.00 8.00 7.50 7.30 8.30 8.40 8.40 8.00 3.20 2.90
13.0 9.30 9.00 9.30 8.40 7.80 7.30
9.0 9.00 8.80 9.95 10.00 9.90 8.00 5.80 5.60 6.60 6.95 7.00 7.00 2.15
14.0 7.60 8.50 7.80 7.20 6.80
10.0 7.20 7.00 8.05 8.45 8.45 8.00 4.60 4.40 5.30 5.80 5.85 5.90 1.25
15.0 6.45 7.45 7.30 6.60 6.30
11.0 5.80 5.55 6.65 7.15 7.25 7.25 3.50 3.30 4.30 4.80 4.90 4.95
16.0 5.50 6.50 6.80 6.20 5.80
12.0 4.60 4.40 5.45 6.05 6.20 6.25 2.65 2.45 3.45 4.00 4.15 4.20
17.0 4.70 5.65 6.25 5.80 5.40
13.0 3.70 3.50 4.50 5.10 5.35 5.40 1.95 1.70 2.70 3.30 3.50 3.55
14.0 2.70 3.70 4.30 4.55 4.70 1.00 2.10 2.70 2.90 3.00 18.0 4.00 4.95 5.50 5.40 5.10
15.0 2.10 3.05 3.60 3.85 4.00 1.55 2.15 2.40 2.50 19.0 3.40 4.30 4.90 5.10 4.80
16.0 1.55 2.50 3.05 3.30 3.45 1.10 1.70 1.95 2.10 20.0 2.85 3.80 4.35 4.55 4.50
17.0 1.10 2.00 2.55 2.80 2.90 1.30 1.55 1.70 21.0 3.30 3.85 4.10 4.20
18.0 0.70 1.60 2.10 2.35 2.50 22.0 2.90 3.40 3.65 3.80
19.0 1.20 1.75 1.95 2.10 24.0 2.15 2.70 2.90 3.05
20.0 0.90 1.40 1.60 1.75 26.0 1.60 2.10 2.30 2.40
21.0 0.60 1.10 1.30 1.45 28.0 1.60 1.80 1.90
22.0 0.85 1.05 1.20 30.0 1.20 1.35 1.50
Critical 32.0 0.85 1.00 1.10
─ ─ 30° 40° 50° 54° 57° ─ ─ 46° 53° 60° 63° 65° ─ 40° 64°
33.0 0.85 0.95
boom angle
Standard for 48 ton 34.0 0.70 0.80
for 34 ton for 48 ton for 34 ton for 48 ton for 34 ton
hook 35.0 0.55 0.70
Hook mass 470kg 330kg 470kg 330kg 470kg 330kg 36.0 0.55
Parts of line 10 7 5 4 4 4 4 10 7 5 4 4 4 4 10 7 5 Critical ─ ─ ─ ─ ─ 23° 29°
boom angle
Standard for 70*/48 ton for 34 ton
hook
Hook mass 530*/470kg 330kg
Parts of line 16*/10 7 5 4 4 4 4

2
 44.5m Boom＋8.3m SLJib
(7.6m) (7.2m) (6.5m)
Outriggers fully extended (7.6m) (over side and over rear) Outriggers intermediately extended (7.2m) (over side) Outriggers intermediately extended (6.5m) (over side)
Boom Offset 7° Offset 25° Offset 45° Offset 60° Boom Offset 7° Offset 25° Offset 45° Offset 60° Offset 7° Offset 25° Offset 45° Offset 60°
Boom
angle Working Load Working Load Working Load Working Load angle Working Load Working Load Working Load Working Load angle Working Load Working Load Working Load Working Load
(° ) radius (m) (ton) radius (m) (ton) radius (m) (ton) radius (m) (ton) (° ) radius (m) (ton) radius (m) (ton) radius (m) (ton) radius (m) (ton) (° ) radius (m) (ton) radius (m) (ton) radius (m) (ton) radius (m) (ton)
84 5.8 4.00 8.6 3.00 10.4 1.90 11.2 1.00 84 5.8 4.00 8.6 3.00 10.4 1.90 11.2 1.00 84 5.8 4.00 8.6 3.00 10.4 1.90 11.2 1.00
80 10.3 4.00 12.8 3.00 14.4 1.90 14.7 1.00 80 10.3 4.00 12.8 3.00 14.4 1.90 14.7 1.00 80 10.3 4.00 12.8 3.00 14.4 1.90 14.7 1.00
77 13.4 4.00 15.8 3.00 17.0 1.85 17.3 1.00 77 13.4 4.00 15.8 3.00 17.0 1.85 17.3 1.00 77 13.4 4.00 15.8 3.00 17.0 1.85 17.3 1.00
75 15.5 4.00 17.5 3.00 18.7 1.80 19.0 1.00 75 15.5 4.00 17.5 3.00 18.7 1.80 19.0 1.00 75 15.5 4.00 17.5 3.00 18.7 1.80 19.0 1.00
73 17.3 3.70 19.3 2.75 20.3 1.75 20.7 1.00 73 17.3 3.70 19.3 2.75 20.3 1.75 20.7 1.00 73 17.3 3.70 19.3 2.75 20.3 1.75 20.7 1.00
70 19.9 3.20 21.8 2.45 22.8 1.65 23.1 1.00 70 19.9 3.20 21.8 2.45 22.8 1.65 23.1 1.00 70 19.7 2.90 21.8 2.45 22.8 1.65 23.1 1.00
68 21.7 2.90 23.5 2.25 24.5 1.60 24.6 1.00 68 21.7 2.80 23.5 2.25 24.5 1.60 24.6 1.00 68 21.2 2.35 23.3 2.00 24.5 1.60 24.6 1.00
65 24.1 2.30 25.8 2.05 26.8 1.55 26.8 1.00 65 23.8 2.10 25.7 1.85 26.8 1.55 26.8 1.00 65 23.5 1.60 25.5 1.40 26.7 1.30 26.8 1.00
63 25.7 1.80 27.3 1.70 28.3 1.50 28.2 1.00 63 25.3 1.65 27.1 1.45 28.2 1.40 28.2 1.00 63 25.0 1.20 27.0 1.00 28.1 0.95 28.2 1.00
60 27.7 1.35 29.4 1.20 30.3 1.15 60 27.5 1.10 29.3 1.00 30.2 0.95 60 27.2 0.65 29.1 0.60 30.1 0.55
57 29.8 0.90 31.4 0.80 32.3 0.75 57 29.6 0.70 31.3 0.60 32.2 0.55 Critical
54 31.8 0.55 33.4 0.45 34.0 0.45 Critical 59° 59° 59° 62°
56° 56° 56° 62° boom angle
Critical boom angle Standard hook for 5 ton (Hook mass : 120kg)
53° 53° 53° 62°
boom angle Standard hook for 5 ton (Hook mass : 120kg) Parts of line 1
Standard hook for 5 ton (Hook mass : 120kg) Parts of line 1
Parts of line 1

Outriggers extended（over front）

Boom
(5.4m) (4.3m) angle
Offset 7° Offset 25° Offset 45° Offset 60°
(° ) Working Load Working Load Working Load Working Load
Outriggers intermediately extended (5.4m) (over side) Outriggers intermediately extended (4.3m) (over side) radius (m) (ton) radius (m) (ton) radius (m) (ton) radius (m) (ton)
Offset 7° Offset 25° Offset 45° Offset 60° Offset 7° Offset 25° Offset 45° Offset 60° 84 5.8 4.00 8.6 3.00 10.4 1.90 11.2 1.00
Boom Boom
80 10.3 4.00 12.8 3.00 14.4 1.90 14.7 1.00
angle Working Load Working Load Working Load Working Load angle Working Load Working Load Working Load Working Load
(° ) radius (m) (ton) radius (m) (ton) radius (m) (ton) radius (m) (ton) (° ) radius (m) (ton) radius (m) (ton) radius (m) (ton) radius (m) (ton) 77 13.4 4.00 15.8 3.00 17.0 1.85 17.3 1.00
75 15.5 4.00 17.5 3.00 18.7 1.80 19.0 1.00
84 5.8 4.00 8.6 3.00 10.4 1.90 11.2 1.00 84 5.8 4.00 8.6 3.00 10.4 1.90 11.2 1.00 73 17.3 3.70 19.3 2.75 20.3 1.75 20.7 1.00
80 10.3 4.00 12.8 3.00 14.4 1.90 14.7 1.00 80 10.3 4.00 12.8 3.00 14.4 1.90 14.7 1.00 70 19.9 3.20 21.8 2.45 22.8 1.65 23.1 1.00
77 13.4 4.00 15.8 3.00 17.0 1.85 17.3 1.00 77 13.0 3.40 15.8 2.55 17.0 1.85 17.3 1.00 68 21.7 2.90 23.5 2.25 24.5 1.60 24.6 1.00
75 15.1 3.60 17.5 3.00 18.7 1.80 19.0 1.00 75 14.8 2.45 17.2 2.00 18.7 1.70 19.0 1.00 65 24.1 2.45 25.8 2.05 26.8 1.55 26.8 1.00
73 16.7 3.00 19.0 2.55 20.3 1.75 20.7 1.00 73 16.5 1.75 18.8 1.40 20.3 1.30 20.7 1.00 63 25.7 2.25 27.4 1.90 28.3 1.50 28.2 1.00
70 19.1 2.10 21.4 1.65 22.7 1.55 23.1 1.00 Critical 60 27.9 1.75 29.6 1.60 30.3 1.45
72° 72° 72° 72°
68 20.7 1.50 23.0 1.20 24.3 1.10 24.6 1.00 boom angle 57 30.0 1.30 31.7 1.15 32.3 1.15
Critical Standard hook for 5 ton (Hook mass : 120kg) 54 32.0 0.90 33.6 0.80 34.0 0.80
67° 67° 67° 67°
boom angle Parts of line 1 49 35.2 0.40 36.5 0.35 37.0 0.35
Standard hook for 5 ton (Hook mass : 120kg) Critical
Parts of line 1 48° 48° 48° 62°
boom angle
Standard hook for 5 ton (Hook mass : 120kg)
Parts of line 1

44.5m Boom＋13.2m SLJib

(7.6m) (7.2m) (6.5m)

Outriggers fully extended (7.6m) (over side and over rear) Outriggers intermediately extended (7.2m) (over side) Outriggers intermediately extended (6.5m) (over side)
Boom Offset 7° Offset 25° Offset 45° Offset 60° Boom Offset 7° Offset 25° Offset 45° Offset 60° Boom Offset 7° Offset 25° Offset 45° Offset 60°
angle Working Load Working Load Working Load Working Load angle Working Load Working Load Working Load Working Load angle Working Load Working Load Working Load Working Load
(° ) radius (m) (ton) radius (m) (ton) radius (m) (ton) radius (m) (ton) (° ) radius (m) (ton) radius (m) (ton) radius (m) (ton) radius (m) (ton) (° ) radius (m) (ton) radius (m) (ton) radius (m) (ton) radius (m) (ton)
84 7.2 2.50 11.0 1.50 14.3 1.00 15.7 0.60 84 7.2 2.50 11.0 1.50 14.3 1.00 15.7 0.60 84 7.2 2.50 11.0 1.50 14.3 1.00 15.7 0.60
80 11.8 2.50 15.5 1.50 18.2 1.00 19.5 0.60 80 11.8 2.50 15.5 1.50 18.2 1.00 19.5 0.60 80 11.8 2.50 15.5 1.50 18.2 1.00 19.5 0.60
77 15.3 2.50 18.6 1.50 21.0 1.00 22.2 0.60 77 15.3 2.50 18.6 1.50 21.0 1.00 22.2 0.60 77 15.3 2.50 18.6 1.50 21.0 1.00 22.2 0.60
75 17.5 2.50 20.6 1.50 22.9 1.00 23.8 0.60 75 17.5 2.50 20.6 1.50 22.9 1.00 23.8 0.60 75 17.5 2.50 20.6 1.50 22.9 1.00 23.8 0.60
73 19.6 2.50 22.5 1.45 24.8 1.00 25.4 0.60 73 19.6 2.50 22.5 1.45 24.8 1.00 25.4 0.60 73 19.6 2.50 22.5 1.45 24.8 1.00 25.4 0.60
70 22.5 2.20 25.2 1.40 27.3 1.00 27.8 0.60 70 22.5 2.20 25.2 1.40 27.3 1.00 27.8 0.60 70 22.5 2.20 25.2 1.40 27.3 1.00 27.8 0.60
68 24.5 2.05 27.0 1.35 29.0 1.00 29.4 0.60 68 24.5 2.05 27.0 1.35 29.0 1.00 29.4 0.60 68 24.2 1.80 27.0 1.35 29.0 1.00 29.4 0.60
65 27.2 1.85 29.6 1.30 31.4 1.00 31.5 0.60 65 27.1 1.65 29.6 1.30 31.4 1.00 31.5 0.60 65 26.6 1.25 29.4 1.10 31.4 1.00 31.5 0.60
63 28.9 1.50 31.2 1.25 32.9 0.95 32.9 0.60 63 28.7 1.30 31.1 1.20 32.9 0.95 32.9 0.60 63 28.3 0.90 31.0 0.80 32.7 0.70 32.9 0.60
60 31.2 1.05 33.6 0.95 35.3 0.90 60 31.0 0.85 33.4 0.80 34.9 0.75 Critical
58 32.5 0.85 35.2 0.70 36.5 0.70 58 32.3 0.65 34.9 0.55 36.2 0.45 62° 62° 62° 62°
boom angle
55 34.5 0.55 37.2 0.40 38.3 0.40 Critical
57° 57° 57° 62° Standard hook for 5 ton (Hook mass : 120kg)
Critical boom angle
54° 54° 54° 62°
boom angle Standard hook for 5 ton (Hook mass : 120kg) Parts of line 1
Standard hook for 5 ton (Hook mass : 120kg) Parts of line 1
Parts of line 1

Outriggers extended（over front）

Boom
(5.4m) (4.3m) angle
Offset 7° Offset 25° Offset 45° Offset 60°
(° ) Working Load Working Load Working Load Working Load
Outriggers intermediately extended (5.4m) (over side) Outriggers intermediately extended (4.3m) (over side) radius (m) (ton) radius (m) (ton) radius (m) (ton) radius (m) (ton)
Offset 7° Offset 25° Offset 45° Offset 60° Offset 7° Offset 25° Offset 45° Offset 60° 84 7.2 2.50 11.0 1.50 14.3 1.00 15.7 0.60
Boom Boom
80 11.8 2.50 15.5 1.50 18.2 1.00 19.5 0.60
angle Working Load Working Load Working Load Working Load angle Working Load Working Load Working Load Working Load
(° ) radius (m) (ton) radius (m) (ton) radius (m) (ton) radius (m) (ton) (° ) radius (m) (ton) radius (m) (ton) radius (m) (ton) radius (m) (ton) 77 15.3 2.50 18.6 1.50 21.0 1.00 22.2 0.60
75 17.5 2.50 20.6 1.50 22.9 1.00 23.8 0.60
84 7.2 2.50 11.0 1.50 14.3 1.00 15.7 0.60 84 7.2 2.50 11.0 1.50 14.3 1.00 15.7 0.60 73 19.6 2.50 22.5 1.45 24.8 1.00 25.4 0.60
80 11.8 2.50 15.5 1.50 18.2 1.00 19.5 0.60 80 11.8 2.50 15.5 1.50 18.2 1.00 19.5 0.60 70 22.5 2.20 25.2 1.40 27.3 1.00 27.8 0.60
77 15.3 2.50 18.6 1.50 21.0 1.00 22.2 0.60 77 15.3 2.50 18.6 1.50 21.0 1.00 22.2 0.60 68 24.5 2.05 27.0 1.35 29.0 1.00 29.4 0.60
75 17.5 2.50 20.6 1.50 22.9 1.00 23.8 0.60 75 17.0 2.00 20.6 1.50 22.9 1.00 23.8 0.60 65 27.2 1.85 29.6 1.30 31.4 1.00 31.5 0.60
73 19.5 2.35 22.5 1.45 24.8 1.00 25.4 0.60 73 18.8 1.40 22.3 1.10 24.6 1.00 25.4 0.60 63 28.9 1.70 31.2 1.25 32.9 0.95 32.9 0.60
70 22.0 1.60 25.0 1.30 27.3 1.00 27.8 0.60 Critical 60 31.4 1.45 33.8 1.20 35.3 0.90
72° 72° 72° 72°
68 23.5 1.20 26.8 0.90 28.9 0.85 29.4 0.60 boom angle 58 32.9 1.15 35.3 1.05 36.6 0.90
Critical Standard hook for 5 ton (Hook mass : 120kg) 55 35.0 0.80 37.3 0.75 38.5 0.70
67° 67° 67° 67°
boom angle Parts of line 1 50 37.9 0.45 40.0 0.40 40.8 0.40
Standard hook for 5 ton (Hook mass : 120kg) Critical
Parts of line 1 49° 49° 49° 62°
boom angle
Standard hook for 5 ton (Hook mass : 120kg)
Parts of line 1

3
 ■When the outriggers are not used
(Unit : Metric ton)

Stationary on rubber Pick & carry (less than 2 km/h)

10.0m Boom 16.9m Boom 23.8m Boom 10.0m Boom 16.9m Boom 23.8m Boom
Working Working
radius (m) 360° 360° 360° 360° 360° 360° radius (m)
Over Over Over Over Over Over
full full full full full full
front front front front front front
range range range range range range
3.5 20.00 12.00 15.00 8.50 9.00 4.50 14.50 8.00 10.50 6.50 7.50 3.30 3.5
4.0 20.00 9.80 15.00 8.50 9.00 4.50 14.50 7.00 10.50 6.50 7.50 3.30 4.0
4.5 17.40 8.00 15.00 7.20 9.00 4.50 12.50 6.00 10.50 5.40 7.50 3.30 4.5
5.0 15.50 6.60 15.00 6.10 9.00 4.50 11.00 5.10 10.50 4.50 7.50 3.30 5.0
5.5 14.00 5.50 13.70 5.10 9.00 4.50 10.00 4.30 10.50 3.75 7.50 3.30 5.5
6.0 12.80 4.65 12.40 4.25 9.00 3.80 9.10 3.60 9.50 3.15 7.50 2.90 6.0
6.5 11.70 3.90 11.30 3.60 8.60 3.20 8.40 3.00 8.60 2.70 7.00 2.50 6.5
7.0 10.70 3.20 10.30 3.00 8.20 2.70 7.80 2.50 7.80 2.25 6.55 2.00 7.0
7.5 9.40 2.50 7.80 7.10 1.85 6.10 7.5
8.0 8.60 1.90 7.40 6.50 1.50 5.70 8.0
8.5 7.70 1.40 7.00 5.85 1.20 5.35 8.5
9.0 7.00 6.60 5.30 0.90 5.00 9.0
10.0 5.70 5.50 4.30 4.10 10.0
11.0 4.75 4.60 3.50 3.35 11.0
12.0 4.00 3.75 2.90 2.65 12.0
13.0 3.35 3.05 2.45 2.00 13.0
14.0 2.50 1.50 14.0
15.0 2.00 1.00 15.0
16.0 1.60 16.0
17.0 1.20 17.0
18.0 0.80 18.0
Critical Critical
boom angle
─ ─ ─ 49° 30° 68° ─ ─ ─ 49° 41° 68°
boom angle
Standard Standard
hook
for 34 ton for 34 ton hook
Hook mass 330kg 330kg Hook mass
Parts of line 5 5 Parts of line

4
■Notes for the lifting capacity chart
■When the outriggers are used ■When the outriggers are not used
1. The lifting capacity charts are based on the jib stowed on the 1. The lifting capacity charts are based on the jib stowed on the
boom side. boom side.
2. The lifting capacity chart indicates the maximum load which can 2. The lifting capacity chart indicates the maximum load the crane
be lifted by this crane provided it is level and standing on firm can lift when its body is level on firm level ground with all tires
level ground. The values in the chart include the mass of the inflated to the rated pressure and the suspension cylinder
main hook and slings for boom operation, and auxiliary hook completely retracted. The values in the chart include the mass
and slings for jib operation. [70 ton hook (mass: 530kg), 48 ton of the main hook and slings.
hook ( mass: 470kg), 34 ton hook ( mass: 330kg), 5 ton hook Within the chart the figures in the area bordered with a thick line
(mass: 120kg) ] are based on structural limitations while other figures are
Within the chart the figures in the area bordered with a thick line determined by stability limitations.
are based on structural limitations while other figures are [Tire pressure: 800kPa (8.0kgf/cm2)]
determined by stability limitations. 3. The working radii are the actual values allowing for boom
3. The working radii are the actual values allowing for boom and jib deflection. Therefore you must always operate the crane on the
deflection. Therefore you must always operate the crane on the basis of the working radius.
basis of the working radius. 4. The lifting capacity differs between the front area capacity and
4. The jib working radius is based on the jib mounted on the end of the full range capacity. When slewing from the front to the side,
the 44.5m boom. When operating at other boom lengths, use take care that the crane could not be over loaded.
the boom angle alone as the criterion.
5. Do not operate the jib when the outriggers are completely
retracted.
6. The lifting capacities for the over sides vary with the outrigger
extension width. Therefore for each outrigger extension Stationary
Pick and carry
Crane operation crane-on-rubber
condition you should work according the lifting capacity chart. operation
operation
Use the front area lifting capacity chart for the front area lifting Area α◦ 1 1
capacity, and the lifting capacity chart of outrigger full extension
for the rear area lifting capacity. 5. The lifting capacity of the rooster sheave is the lifting capacity of
the boom minus the mass of the 34 ton hook (330kg), with an
upper limit of 5,000kg.
[The hook for use with the rooster shave is the 5 ton hook (mass:
120kg) with one part of line.]
Outrigger Full extension
Intermediate
Intermediate
6. Do not work with the jib or with a boom length of more than
(7.6m) extension Full retraction 23.8m.
extension status (7.2 ― 5.4m) extension (4.3m)

Area α◦ Only front area 40 30 15 3

7. For stationary crane-on-rubber operation, the parking brake and
service brake lock device must be engaged.
7. The lifting capacity of the rooster sheave is the lifting capacity of 8. For pick and carry operation, the super-slow speed switch must
the boom minus the mass of all attached hook, slings etc. to the be switched to“ON”and the shift lever set to speed 1.
boom, with an upper limit of 5,000kg. 9. For pick and carry operation, lower the load to just above the
[The hook for use with the rooster sheave is the 5 ton hook ground and keep your speed strictly below 2km/h to avoid
(mass: 120kg) with one part of line.] swinging the load.
8. If the boom length, boom angle jib length, jib angle and/or Take particular care to avoid sharp turns, sudden starts and
working radius exceeds the rated value, use the lifting capacity stops.
for the rated value or for the next one, whichever gives the 10. Never operate the crane during pick and carry operation. The
smaller lifting capacity. slewing brake must be applied.
9. If you are working with the boom while the jib is rigged, subtract 11. If the boom length or working radius exceeds the rated value,
2.6 ton from the each lifting capacity of the boom for the use the lifting capacity for the rated value or for the next one,
outrigger extension width 7.6m, 7.2m, 6.5m or 5.4m, and 3.0 ton whichever gives the smaller lifting capacity.
for the outrigger extension width 4.3m, with an upper limit of 18 12. In whatever working conditions the corresponding boom critical
ton. angel is shown in the chart. The crane can tip over if the boom
Do not use the rooster sheave in this situation. And do not is lowered below the critical angle even if unloaded.
operate the boom while the jib is rigged, when the outriggers are Therefore, never lower the boom below these angles.
retracted. 13. The standard parts of line for each boom length are as indicated
[The main hook for use with the jib rigged is 34 ton hook (mass: in the chart. If you work with a non-standard number of parts of
330kg).] line, do not exceed 45.1kN (4.6tf) per wire rope respectively.
10. In whatever working conditions the corresponding boom critical 14. Crane operation is permissible up to a wind speed of 10m/s.
angel is shown in the chart. The crane can tip over if the boom Even in relatively light wind conditions, extra care should be
is lowered below the critical angle even if unloaded. taken when handling loads presenting large wind catching
Therefore, never lower the boom below these angles. areas.
11. If you work with 16 parts of line on the hook (with * marked in 15. Kato bears no liability whatsoever for damage, crane tipping or
the lifting capacity chart), use the rooster sheave and sheave other accident caused by crane operations which differ from the
bracket. directions contained in the instruction manual and the warning
12. The standard parts of line for each boom length are as indicated labels.
in the chart. If you work with a non-standard number of parts of
line, do not exceed 45.1kN (4.6tf) per wire rope respectively.
13. Crane operation is permissible up to a wind speed of 10m/s.
Even in relatively light wind conditions, extra care should be
taken when handling loads presenting large wind catching
areas.
14. Kato bears no liability whatsoever for damage, crane tipping or
other accident caused by crane operations which differ from the
directions contained in the instruction manual and the warning
labels.

5
 ■WORKING RANGE

62133000

6
■Minimum path width
●Left turn in two-wheel steering mode ●Left turn in 4-wheel steering mode

・R1=11.20m ・A=5.86m (Width of entrance) ・R1=6.44m ・A0=5.39m (Width of entrance)

(Minimum turning radius) ・B=5.86m (Width of wheel exit) (Minimum turning radius) ・A1=3.84m (Width of wheel entrance)
・R2=11.45m ・C=6.75m (Width of chassis exit) ・R2=6.69m ・B =3.84m (Width of wheel exit)
(Turning radius of extremely ・D=8.11m (Width of exit at end of boom) (Turning radius of ・C =5.39m (Width of chassis exit)
outer tyre) extremely outer tyre) ・D =6.90m (Width of exit at end of boom)
・R3=12.34m ・R3=7.68m
(Chassis turning radius) (Chassis turning radius)
・R4=13.70m ・R4=9.13m
(Boom end turning radius) (Boom end turning radius)
・R5=7.13m ・R5=3.14m
(Turning radius extremely chassis inner) (Turning radius extremely chassis inner)
Note: The above values are based on calculations.

■Overall view

Reduced scale: 1/100 Unit (mm)

7
 ■Overall view

Reduced scale: 1/100 Unit (mm)

* KATO products and specifications are subject to improvements and changes without notice.

Address inguiries to:

9-37, Higashi-ohi 1-chome,Shinagawa-ku, Tokyo, 140-0011, Japan

Tel. : Head Office Tokyo (03) 3458-1111
Overseas Marketing Department. Tokyo (03) 3458-1115
Fax. : Tokyo (03) 3458-1163
URL http://www.kato-works.co.jp

C02651
10.2008-3000 (TI) 1 We acquired the "ISO 9001" certification which is
an international standard for quality assurance.