VII.

Slow Flight and Stalls

VIII. Basic Instrument Maneuvers
IX. Emergency Operation
Using the ACS
X. Multiengine Operations
PA.I.C.KC XI. Night Operations
(Applicable ACS. XII. Postflight Procedures
Area of Operation.
Task. Aircraft Performance
Task Element Knowledge)
Weight and Balance
ASEL: Airplane – Single-Engine Land
ASES: Airplane – Single-Engine Sea Even though an aircraft has been certified for flight at a specified maximum gross
AMEL: Airplane – Multiengine Land weight, it may no be safe to take off with that load under all condition. High
AMES: Airplane – Multiengine Sea altitude, high temperature, and high humidity are additional factors which may
require limiting the load to some weight less than the maximum allowable.
Checkride Minimum Elements
Some of the problems caused by overloading an aircraft are:
From each applicable Task:
the aircraft will need a higher takeoff speed, which results in a longer
At least one knowledge element takeoff run
At least one risk management element both the rate and angle of climb will be reduced
All skill elements the service ceiling will be lowered
any Task elements in which the applicant was shown to be deficient on the the cruising speed will be reduced
knowledge test cruising range will be shortened
maneuvering will be decreased
Knowledge Test a longer landing roll will be required because the landing speed will be
higher
#Regulations
excessive loads will be imposed on the structure, especially the landing gear
#Accident_Reporting
#Performance_Charts
Empty weight: obtained from the appropriate charts.
#Radio_Communications
#Weather it includes the airframe, engine, all fixed equipment, and unusable
#Safe_and_Efficient_Operation fuel and oil.
#Density_Altitude some aircraft include all oil in the aircraft empty weight
#Weight_and_Balance
#Aerodynamics_Powerplants_and_Aircraft_Systems Useful Load: includes the pilot, passengers, baggage, fuel and oil
#Stalls_and_Spins
#Aeronautical_Decision-Making_ADM
Takeoff weight: is the empty weight plus the useful load
#Preflight_action

Sections Landing weight: the takeoff weight minus any fuel used

I. Preflight Preparation
II. Preflight Procedures
III. Airport and Seaplane Base Operations
IV. Takeoff, Landings, and Go-Arounds
V. Performance and Ground Reference Maneuvers
VI. Navigation

Item Weight
General aviation crew and passenger 190lbs each
Gasoline 6lbs/gallon
Oil 7.5lbs/gallon
Water 8.35lbs/gallon

Airplane
In addition to considering the weight to be carried, the pilot must ensure that the
load is arranged to keep the aircraft balance.

The balance point, or CG, is the point at which all of the weight of the
airplane is considered to be concentrated.
For an aircraft to be safe to fly, the center of gravity must fall between
specified limits

Each category has specific balance requirements

To keep the CG within safe limits it may be necessary to move weight
toward the nose of the aircraft (which moves the CG forward) or move the
weight toward the tail (moving the CG aft)
The arm is the horizontal distance measured in inches from the datum
line to a point on the aircraft
Computing Weight and Balance Problems Using a Table
If measured aft, toward the tail, the arm is given a positive (+)
value.
If measured forward, toward the nose, the arm is given a negative
(-) value
The moment is the product of the weight of an object multiplied by its
arm and is expressed in pound-inches (lbs-in)
Formula: Weight x Arm = moment
The moment index is a moment divided by a constant such as 100 or
1,000
It is used to simplify computations where heavy items and long arms
result in large, unmanageable numbers. This is usually expressed as
Moment/100 or Mom/1,000

The center of gravity (CG) is the point about which an aircraft will balance and it
is expressed in inches from the datum.
The center of gravity is found by dividing the total moment by the total weight and
the for is:
(total moment)/(total weight) = CG(inches aft of datum)

Standard Weights

have been established for numerous items involved in weights and balance
computations.
These weights should not be used if actual weights are available. Some standard
weights are:
 Computing Weight and Balance Problems Using a Graph

Takeoff Distance
Density Altitude and Aircraft Performance
The Takeoff Distance Graph FAA Figure 40, allows the pilot to determine the ground
Aircraft performance charts show a pilot what can be expected of an airplane (rate roll required for take off under various conditions.
of climb, takeoff roll, etc) under stipulated conditions It shows the total distance required for a takeoff and climb to clear a 50-foot
obstacle
Prediction of performance is based upon sea level temperature of 15C (+59F) and
atmospheric pressure of 22.92Hg
This combination of temperature and pressure is called standard day
When the air is at standard density, temperature and/or pressure deviations will
change the air density, or the density altitude, which affects aircraft
performance.

Performance charts allow the pilot to predict how an aircraft will perform

Relative humidity also affects density altitude, but is not considered when the
performance charts are formulated:

a combination of high temperature, high humidity, and high altitude result in

a density altitude higher than the pressure altitude which in turn results in
reduced aircraft performance

Cruise Power Setting Table

The Cruise Power Setting Table FAA Figure 35 may be used to forecast fuel flow and
true airspeed and therefore allow a pilot to determine the amount of fuel required
and the estimated time en-route
 The graph shown in FAA Figure 36 is used to determine what extent a wind of a given
direction and speed is felt as a headwind and/or crosswind

Maximum Range Performance

Maximum endurance is obtained at the point of minimum power to maintain the
Landing Distance Graphs and Tables aircraft in steady, level flight
Some Landing Distance Graphs such as FAA Figure 37, 38 are used in the same manner
When range and economy of operation are the principal goals, the pilot must ensure
as the takeoff distance graph.
that the airplane will be operated at the recommended long-range cruise performance

Aircraft Systems
Reciprocating Engines

Pistons move back and forth within the cylinders

Connecting rods connect the pistons to the crankshaft, which converts
the and forth movements of the pistons to a rotary motion
This rotary motion drives the propeller'

One cycle of the engine consists of two revolutions of the crankshaft.

These two crankshaft revolutions require four strokes of the piston:

intake
compression
Headwind and Crosswind Component Graph power
exhaust
In general taking off into a wind improves aircraft performance, and reduces the
length of the runway required to become airborne.
The stronger the wind, the better the aircraft performs.

Crosswinds, however, may make the aircraft difficult or impossible to control.

The aircraft manufacture determines the safe limit for taking off or landing
with a crosswind and establishes the maximum allowable crosswind component.

Fuel Induction Systems

Carburetor Induction System: The float-type carburetor takes in air that

flows through a restriction (venturi) which creates a low-pressure area.
The pressure difference between the low-pressure area and outside air forces
fuel into the airstream where it is mixed with the flowing air, drawn
through an intake manifold, and delivered to he combustion chambers and
ignited

Carburetors are normally set to deliver the correct air/fuel mixture

at sea level.
since air density decreases with altitude, a mixture control allows
the pilot to decrease the fuel flow as altitude increases and this
maintain the correct mixture: otherwise the mixture becomes too rich
at high altitudes
When descending air density increases: unless fuel flow is increased,
the mixture may become lean

Ignition and Electrical Systems Fuel Injection System: the fuel and air are mixed just prior to entering the
Most reciprocating engines used to power small aircraft incorporate two separate combustion chamber (no carburetor is used)
magneto ignition systems
Carburetor Ice
magneto is a self-contained source of electrical energy, to even if an
aircraft loses total electrical power, the engine will continue to run As air flows through a carburetor it expands rapidly.
At the same time fuel forced into the airstream is vaporized.
When checking for magneto operation prior to flight, the engine should Expansion of the air and vaporization of the fuel causes a sudden cooling of the
run smoothly when operating with the magneto selector set on "BOTH" and mixture which may cause ice to form inside the carburetor.
should experience a slight drop revolutions per minute (RPM) when running The possibility of icing should always be considered when operating in conditions
on only one magneto where the temperature is between 20F and 70f and the relative humidity is high

The main advantages of the dual ignition system are increased safety and improved Carburetor heat preheats the air before it enters the carburetor and either
engine performance prevents ice from forming or may melt the ice

When carburetor heat is applied the heated air that enters carburetor is less
dense.
this causes the fuel/air mixture to become enriched and this in turn
decreases engine output and increases engine operating temperatures

During engine runup prior to departure from a high-altitude airport, the

pilot may notice a slight engine roughness which is not affected by the
magneto check, but grows worse during the carburetor heat check: in this
case the air/fuel mixture may be too rich due to the lower air density at
the high altitude and applying carburetor heat decreases the air density
even more. A leaner setting of the mixture control may correct this problem

In a fixed-pitch propeller airplane, the first indication of carburetor ice would

likely be a decrease in RPM as the air supply is choked off. Application of
carburetor heat will decrease air density, cause the RPM to drop even lower. Then
If the engine oil temperature and cylinder head temperature gauges have
as the ice melts, the RPM will rise gradually exceeded their normal operating range, or if the pilot suspects that the

Fuel injection systems do not utilize a carburetor and are generally considered to engine is detonating during climb out:

be less susceptible to icing than carburetor systems are the pilot may be operating with either too much power and the mixture
set to lean
Aviation Fuel using fuel of too low a grade

Fuel does 2 things for the engine: or operating the engine with insufficient amount of oil in it
reducing the climb rate and increasing airspeed enriching the fuel
it acts as an agent for combustion mixture, retarding the throttle will aid in cooling an engine that is
an agent for cooling (based on mixture setting) overheating

Aviation fuel is available in several grades. The proper grade will be listed, a The most important rule to remember in the even of a power failure after becoming
higher grade fuel can be used, but a lower grade fuel should not be used: airborne is to maintain safe airspeed

the use of a lower grade fuel in a lean mixture may cause detonation
Propellers
which is the uncontrolled spontaneous explosion of the mixture in the
cylinder (this causes extreme heat) The throttle controls the power output as registered on the manifold pressure
gauge, and the propeller controller regulates the engine RPM.
Preignition: the premature burning of the air/fuel mixture.
It is caused by an incandescent area (such as carbon or lead deposit heated A pilot should avoid a high manifold pressure setting with low RPM on
to a red glow) which serves as an ignition advance of normal ignition engines equipped with a constant-speed propeller. To avoid high manifold
pressure combined with low RPM:
Two fuel pump systems are used on most airplanes:
reduce the manifold pressure before reducing RPM when decreasing power
the main pump system is engine driven and an auxiliary electric driven pump setting
is provided for use in the vent the engine pump fails or increase the RPM before increasing the manifold pressure when
the auxiliary pump (boost pump) provides added reliability and aids in engine increasing power settings
start up

Torque
Engine Temperatures
An airplane of standard configuration has a tendency to turn left.
Engine lubrication oil not only prevents direct metal-to-metal of moving parts, it
This tendency is called torque and is a combination of 4 forces:
also absorbs and dissipates some of the engine heat produced by internal combustion
reactive force
If the engine oil level should fall too low, an abnormally high engine oil
spiraling slipstream
temperature indication may result
gyroscopic precession
On the ground or in the air, excessively high engine temperature can cause P-factor
excessive oil consumption, loss of power, and possible internal engine damage

Reactive force: is based on Newton's Law of action and reaction Spiraling slipstream: the reaction of the air to rotating propeller

A propeller rotating in a clockwise direction (as seen from the rear) the propeller forces the air to spiral in a clockwise direction around
produces a force which tend to roll the airplane in a counter-clockwise the fuselage
direction this spiraling slipstream strikes the airplanes vertical stabilizer on
the left side
this pushes the tail of the airplane to the right and nose of the
airplane to the left
 The use of a written checklist for preflight inspection and starting the engine is
Gyroscopic precession: the result of a deflective force applied to a
rotating body recommended to ensure that all necessary items are checked in a logical sequence

the resultant action occurs at 90 degree later in the direction of Airspace

rotation
Controlled airspace, airspace within which some or all aircraft may be subject to
air traffic control, consists of those areas designated Class A, B, C, D, E
airspace

Much of the controlled airspace begins at either 700ft or 1,200ft above the
ground.
The lateral limits and floors of Class E airspace of 700 ft are defined by a
magenta vignette; while the lateral limits and floors of 1,200ft are defined by
a blue vignette if it abuts uncontrolled airspace
Floors other than 700ft or 1,200ft are indicated by a number indicating the
floor

Class A airspace
Class A airspace extends from 18,000ft MSL up to and including FL6000 and is
not depicted on VFR sectional charts.

No flight under VFR, including VFR-On-Top is authorized in Class A

airspace

Class B airspace
Class B airspace consists of controlled airspace extending upward from the
Asymmetric propeller loading (P-factor): caused by the downwind moving blade surface or higher to specified altitudes
on the right side of the propeller having a higher angle attack, a greater
Each class B airspace sector, outlined in blue on the sectional chart
action and reaction, and therefore a higher thrust than the upward moving
is labeled with its delimiting altitudes
opposite blade. This results in a tendency for the aircraft to yaw to the
Each Class B airspace location will contain at least one primary
left around the vertical axis
airport
additional left-turning tendency from torque will be greatest when the An ATC clearance is required prior to operating within Class B
aircraft is operating at low airspeed with a high power setting airspace
A pilot landing or taking off from one of a group of 12 specific, busy
airports must hold at least a private pilot certificate.
Preflight Inspection Procedures
At other airports a student pilot may not operate an aircraft on a
A thorough preflight inspection should be performed on an aircraft to help ensure solo flight within Class B airspace, or to from or at an airport
that the aircraft is prepared for safe flight and should be thorough and located within Class B airspace unless both ground and flight
systematic. instruction has been received from an authorized instructor
The students logbook must be authorized within the preceding 90
Prior to every flight, a pilot should at least perform a walk-around inspection of days
the aircraft Each airplane operating within Class B airspace must be equipped with
a two-way radio with appropriate ATC frequencies, and a 4096 code
After an aircraft has been stored for an extended period of time, a special check transponder with Mode C/S automatic altitude-reporting capability
should be made during preflight for damage or obstructions caused by animals, birds
or insects

Class C airspace Class E airspace

All class C airspace has the same dimensions with minor site variations. Will be blue if next to Class G airspace
They are composed of 2 circles both centered on the primary airport Magenta shading identifies class E airspace starting at 700ft AGL and no
shading identifies starting at 1,200ft(varies) AGL
The inner circle (surface area) has a radius of 5 nautical miles and
All airspace from 14,500 to 17,999 feet is Class E airspace
extends from the surface up to 4,000ft above the airport
It also includes the surface of some airports with an instrument approach
The outer circle (shelf area) has a radius of 10 nautical miles and
but no control tower
extends vertically from 1,200ft AGL up to 4,000ft above the primary
airport
An Airway is a corridor of controlled airspace extending from 1,200ft above the
In addition to the Class C airspace proper, there is an outer area
surface or as designated, up to and including 17,999ft MSL, and 4 nautical miles
with a radius of 20 nautical mils and vertical coverage from the lower
either side of the center line
limits of the radio/radar coverage up to the top of the approach control
facility's delegated airspace
Within the outer are, pilots are encouraged to participate but it Class G
is not a VFR requirement
Class G airspace is airspace within which Air Traffic Control has neither
Class C airspace service to aircraft proceeding to a satellite airport
the authority nor responsibility to exercise any control over air traffic.
will be terminated at a sufficient distance to allow time to change to
the appropriate tower or advisory frequency. Typically extends from the surface to the base of the overlying
Aircraft departing satellite airports within Class C airspace shall controlled Class E airspace
establish two-way communication with ATC as soon a practicable after take
In some cases like Alaska, and the western U.S class G airspace may
off
extend to 14,500ft MSL
On charts Class C airspace is depicted by solid magenta lines
Prohibited areas are blocks of airspace within which the flight of an aircraft is
Class D airspace prohibited

Class D airspace extends upward from the surface to approximately 2,500ft Restricted areas denote the presence of unusual, often invisible hazards to
AGL. aircraft such as artillery firing, aerial gunnery, or guided missiles. Penetration
Class D airspace may include one or more airports and is normally 4 nautical of Restricted areas without authorization of the using or controlling agency may be
miles in radius. extremely hazardous

When the ceiling of class D airspace is less than 1,00ft and/or the Warning area contain the same hazardous activities as restricted areas, but are
visibility is less than 3 statute miles, pilots wishing to take off or located in international airspace
land must hold and instrument rating, must have instrument flight plan,
Military Operations Areas (MOAs) consist of airspace established for the purpose of
and must have received clearance from ATC.
separating certain military training activities from IFR traffic.
The aircraft must be equipped to takeoff or land when the weather
is less than that required for visual flight rules
Pilots operating under VFR should exercise extreme caution while flying
When special VFR flight is prohibited it will be depicted by "No SVFR" within an active MOA.
above the airport information on the chart
Any Flight Service Station within 100 miles of the area will provide
information concerning MOA hours of operation
Prior to entering an active MOA pilots should contact the controlling agency
for traffic advisories

Alert Areas may contain a high volume of pilot training activities or an unusual
type of aerial activity, neither of which is hazardous to aircraft.

Pilots of participating aircraft as well as pilots transiting the area are

equally responsible for collision avoidance
Aircraft are requested to remain at least 2,000ft above the surface of National
chord line: imaginary line from the leading edge to the trailing edge of an
Parks, National Monuments, Wilderness and Primitive Areas, and National Wildlife airfoil
Refuges

Military Training Routes (MTRs) have been developed for use by the military for the
purpose of conducting low-altitude, high-speed training.

Generally MTRs are established below 10,000ft MSL for operations at speeds in
excess of 250 knots

IFR Military Training Routes (IR) operations are conducted in accordance with
instrument flight rules, regardless of weather conditions.
VFR Military Training Routes (VR) operations are conducted in accordance with VFR.
IR and VR at and below 1,5000ft AGL will identified by four digit numbers (VR1351,
IR1007)
IR and VR above and below 1,500 AGL will be identified by three digit numbers,
IR341, VR426

Basic Aerodynamic changing the shape of an airfoil (by lowering flaps) will change the
chord line
Aerodynamic Terms

airfoil: structure or body which produces a useful reaction to air movement

airplane wings, helicopter blades and propellers are airfoils

relative wind: wind felt by an airfoil. angle of attack: angle between the chord line of the airfoil and the
relative wind
It is created by the movement of air past an airfoil, by the motion of
an airfoil through the air, or a combination of the two
Relative wind is parallel and in the opposite direction of the flight
path of the airfoil

angle of incidence: angle at which a wing is attached to the aircraft

fuselage

Axes of Rotation and the Four Forces Acting in Flight

Aircraft have three axes of rotation: lateral, longitudinal, and vertical
 lateral axis: imaginary line from wing tip to wing tip

rotation around this axis is called pitch

pitch is controlled by elevators and this rotation is called
longitudinal control/stability

longitudinal axis: imaginary line from nose to tail vertical axis: imaginary line extending through the intersection of the
lateral and longitudinal axes
rotation around this axis is called roll
roll is controlled by the ailerons and this rotation is called lateral rotation around this axis is called yaws
control/stability yaw is controlled by the rudder and this rotation is called
directional control/stability

center of gravity: the point at which an airplane would balance if it were

suspended on that point

The 3 axes intersect at the center of gravity

Weight shift control and powered parachutes rotate around this center
of gravity
Four Forces

Lift

As the velocity of a fluid (gas or liquid) increases, its pressure decreases:

Bernoulli's Principle

Lift is the result of a pressure difference between the top and the bottom
of the wing
Weight
A wing accelerated the air over the top of the wing decreasing the
pressure above the wing Weight is the force with which gravity attracts all bodies vertically toward the
center of the earth
4 factors are involved in creating lift:
Thrust
angle of attack
wing area and shape (planform) Thrust is the forward force which is produced by the propeller acting as an airfoil
air velocity to displace a large mass of air to the rear
air density
Drag
The pilot can control angle of attack and airspeed, increasing either increases
lift. Drag is a rear-ward acting force which resists the forward movement of an airplane
through the air. 2 types of drag: parasite, induced

Parasite drag: the resistance of the air produced by any part of an airplane Stability
that does not produce lift (landing gear, antennae)
Stability is the inherent ability of an airplane to return or not return to its
parasite drag will increase as airspeed increases original flight condition after being disturbed by an outside force, such as rough
air.

Induced drag: a by-product of lift. Drag that is induced as the wing

develops lift

induced drag increases as airspeed increases

During unaccelerated (straight and level) flight the 4 forces are in equilibrium:

lift = weight
thrust = drag
 positive static stability: initial tendency of an aircraft to return or not positive dynamic stability: tendency of an oscillating airplane (with
return to its original position positive static stability) to return to its original position relative to
time

The location of the CG with respect to the center of lift will determine the
longitudinal stability of an airplane:

an airplane will be less stable at all airspeeds if it is loaded to the most

aft CG
a more inherently stable airplane is easier to control

Changed in pitch can also be experienced with changes in power settings, except in
T-tail airplanes

when power is reduced their is reduced downwash on the tail resulting in the
nose pitching down

A properly designed weight-shift control is stable because the center of lift is

above the CG

slower than trim the center of lift moves aft

faster than trim the center of lift moves forward to make the aircraft stable

Effects of Forward CG

1. Increased longitudinal stability

2. Lower cruise speed
3. the wing flies at a higher angle of attack to create more lift to counter the
added downward forced produced by the tail, therefore the wing also produced
more induced drag
4. Higher stall speed
5. the flies at a higher angle of attack to create more lift to counter the added
downward forces produced by the tail, therefore the wing also produces more
induced drag

Effects of Aft CG Centrifugal force: a force that acts toward the outside of the curve any
time an airplane is flying a curved path (turns, climbs, descents)
1. Decreased longitudinal stability
2. Higher cruise speed when the airplane is flying a curved flight the load the wings must
3. Lower cruise speed support will be equal to the weight of the airplane plus the load imposed
4. Lower stall speed by centrifugal force
5. Poor stall/spin recovery as the angle of bank of a turn increases the load factor increases

Turns, Loads, and Load Factors

Horizontal Lift Component: When an airplane is banked into a turn, a portion

of the vertical lift being developed is diverted into horizontal lift
component.
The reduced Vertical Lift Component results in a loss of altitude unless
total lift is increased by:

increasing angle of attack

increasing air speed The amount of excess load that can be imposed on the wing of an airplane depends on
increasing both the speed of the airplane: a change in direction made at high speed with forceful
control movement results in a high load factor

An increased load factor (weight) will cause the airplane to stall at a higher
speed

Some conditions that increase the load (weight) of an aircraft are:

overloading the airplane

too steep an angle of bank
turbulence and abrupt movement of the controls

Load is the force (imposed stress) that must be supported by an airplane structure
in flight.

The loads imposed on the wings in flight are stated in terms of load factor
in straight and level flight the airplane has a load factor of 1 (1 G)
Aircraft are separated into categories determined by the loads that their wing Maneuvers
structures can support.
Rectangular Course

Rectangular course: the flight path should be positioned outside the field
boundaries just far enough that they may be easily observed from either pilot seat
by looking out the side of the airplane.

The closer the track of the airplane is to the field boundaries, the steeper
the bank necessary at the turning points

Turns Around a Point

Turns around a point: the wings will be in alignment with the pylon only during the
time the airplane is flying directly upwind or directly downwind.
At all other points a wind correction angle will keep the wings from pointing
directly at the pylon.

If the student is instructed to not exceed a 45o bank in a turn around a

point maneuver, the best place to start is the point where the bank angle will
be steepest, which is when flying downwind.
throughout the remainder of the maneuver, the bank angle will be
shallowing out S-Turns
The ground speed will be equal where the airplane is flying with the same
headwind component. In visual flight a steep turn is anything grater than 45o
the angle of bank will be the same only where the airplane is flying
directly crosswind In a steep turn the ground speed will be the same when the airplane has the
same headwind component
The steepest angle of bank is required at the points where the airplane is
flying downwind
The airplane will have to be crabbed into the wind the greatest amount where
it is flying crosswind
 In the first half of the S-turn the bank should begin shallow and
increase in steepness as the airplane turns cross wind and becomes
steepest where the turn is downwind
if the turn is started with too steep a bank angle the bank will
increase too rapidly and the upwind half of the "S" will be smaller than
the downwind half
the turn will not be completed by the time the airplane is over the
reference line

An aircraft will spin only after it has stalled, and will continue to spin as long
as the outside wing continues to provide more lift than the inside wing and the
aircraft remains stalled

Flaps
Extending the flaps increases the wing camber and the and of attack of a wing.
This increases wing lift and also increases induced drag.
Stalls and Spins
The increases drag enables the pilot to make steeper approaches to a landing
At an angle of attack of about 18o-20o (for most wings), turbulence over the upper without an increase in airspeed.
wing surface decreases so drastically that flight can not be sustained and the wing VFR approaches to a landing at night should be make the same as during the
*stalls daytime

The angle at which a stall occurs is called the critical angle of attack

an airplane can stall at any airspeed or any altitude, but will always
stall at the same critical angle of attack
the indicated airspeed at which a given airplane will stall in a
particular configuration, will remain the same regardless of altitude
Because air density decreases with an increase inn altitude the airplane
has to be flown at a faster speed at higher altitudes to cause the same
pressure difference between pitot impact pressure and static impact

Wake Turbulence
All aircraft leave two types of wake turbulence:

prop/jet blast
wing-tip vortices

The prop/jet blast could be hazardous to light aircraft on the ground behind
large aircraft which are either taxiing or running-up their engines.

In the air prop/jet blast dissipates rapidly

Wing-tip vortices are a by product of lift

When a wing is flown at a positive angle of attack a pressure

differential is created between the upper and lower wing surface, and the
pressure above the will be lower than the pressure below the wing.
Ground Effect in attempting to equalize the pressure, air moves outward, upward
and around the wingtip: setting up a (vortex) behind each wing

Ground Effect occurs when the airplane is flying within one wingspan or less
above the surface The strength of a vortex is governed by the weight, speed, and the shape of
the wing
maximum vortex strength occurs when the generating aircraft is heavy,
The airflow around the wing and wing tips is modifies and the resulting
clean, and slow
pattern reduces the downwash and the induced drag
These changes can result in an aircraft becoming airborne before reaching Vortices generated by large aircraft in flight tend to sink below the flight
recommended takeoff speed or floating during and approach path of the generating aircraft
a pilot should fly at or above the larger aircrafts flight path in order
An airplane leaving ground effect after takeoff will require an increase in
to avoid wake turbulence created by the wing tip vortices
angle of attack to maintain the same lift coefficient
which in turn will cause an increase in induced drag and therefore Close to the ground, vortices tend to move laterally
require increased thrust a cross wind will tend to hold the upwind vortex over the landing runway
a tailwind may move the vortices of a preceding aircraft forward into the
touchdown zone
To avoid wake turbulence a pilot should not the point where a receding large
aircraft touched down and then land past that point
On takeoff, lift should be accomplished prior to reaching the rotation point
of a preceding large aircraft
the flight path should then remain upwind and above the preceding
aircrafts flight path
 Communication Procedures
Phraseology, Techniques, and Procedures
Automatic Terminal Information Service (ATIS) is a continuous broadcast of non-
control information in selected high-activity terminal areas.
To relieve frequency congestion, pilots are urged to listen to ATIS, an on initial
contact to advise controllers that the information has been received by repeating
the alphabetical code word appended to the broadcast: "information Sierra received"

The phrase "have numbers" does not indicate receipt of the ATIS broadcast

When transmitting an altitude to ATC (up to but not including 18,000ft MSL),
state the separate digits of the thousands, plus the hundreds.

13,500 -> "one three thousand five hindered"

4,500 -> "four thousand five hundred"

At airports with air traffic control towers (ATCT), approval must be

obtained prior to moving an aircraft onto the movement area

Ground control frequencies are provided to reduce congestion on the

tower frequency.
They are used for issuance of taxi information, clearances and
other necessary contacts
If instructed by ground control to "taxi to" a particular runway,
the pilot must stop prior to crossing any runway
A clearance must be obtained prior to crossing any runway
Aircraft arriving at an airport where a control tower is in operation
should not change to ground control frequency until directed to do so by
ATC

The key to operating at an airport without an operating control tower is selection

of the correct Common Traffic Advisory Frequency (CTAF)
 The CTAF is identified in appropriate aeronautical publications and on the
sectional chart.
If the airport has a part-time ATCT, the CTAF is usually a tower frequency
If a flight service station is located on the airport, they will usually
monitor that frequency and provide advisories when the tower is closed
When there is no tower of FSS, UNICOM (if available) is usually the CTAF
UNICOM is limited to the necessities of sage and expeditious operation of
private aircraft pertaining to runways and wind condition, types of fuel,
weather, and dispatching
Communication may be transmitted concerning ground transportation, food,
lodging, and services available during transit.

When no tower, FSS, or UNICOM is available, use MULTICOM frequency 122.9 for self- If the aircraft radios fail while inbound to a tower controlled airport the pilot
announce procedures should remain outside or above the airport traffic area until the direction and
flow of traffic has been determined and then join the airport traffic pattern and
watch the tower for light signals.

The general warning signal (alternating red and green) may be followed by any other
signal.

For example while on final approach for landing, an alternating red and green
light followed by a flashing red light is received from the control tower
under these circumstances, the pilot should abandon the approach
realizing the airport is unsafe for landing

Radar Assistance to VFR Aircraft

Radar-equipped ATC facilities provide traffic advisories and limited vectoring
(called "basic service") to VFR aircraft, provided the aircraft can communicate
with the facility.

Stage II service provides radar advisories and sequencing for VFR aircraft.

Arriving aircraft should initiate contact with approach control.

Approach control will assume Stage II service is requested, unless the pilot
states that the service is not wanted.
Airport Traffic Area Communications and Light Signals Pilots departing VFR should request Stage II terminal radar advisory services
from ground control on initial contact.
Unless otherwise authorized, aircraft are required to maintain two-way radio
communication with the ATCT when operating to, from, or on the controlled airport At some locations Stage III service has been established to provide separation
regardless of the weather. between all participating VFR aircraft and all IFR aircraft in the terminal radar
If radio contact cannot be maintained, ATC will direct traffic by means of light service area (TRSA)
gun signals Unless the pilot states "negative Stage III" on initial contact with approach
control, the service will be provided

Traffic advisories given by a radar service will refer to the other aircraft Pilotage is the use of visible landmarks to maintain a desired course, and
azimuth in terms of the 12-hour clock with 12 o'clock being the is the basic form of navigation for the beginning pilot operating under VFR.
flight(track), not the aircraft heading
Visible landmarks which can be identified on aeronautical charts allow
Each hour is equal to 30o the pilot to proceed from one check point to the next

an aircraft heading 090o is advised of traffic at the 3 o'clock

The aeronautical charts most commonly used by VFR pilots are
position. The pilot should 90o to the right of the direction of
flight, or to the south VFR Sectional Aeronautical Chart
VFR Terminal Area Chart
These radar programs are not to be interpreted as relieving pilots of their World Aeronautical Chart
responsibilities to see and avoid other traffic operations in basic VFR weather
conditions to maintain appropriate terrain and obstruction clearance, or to remain All three charts include aeronautical information such as airports, airways,
in weather conditions equal to or better than the required. special use airspace, and other pertinent data.

Whenever compliance with an assigned route, heading, and/or altitude is Latitude run parallel to the equator
likely to compromise pilot responsibilities respecting terrain, obstruction From the equator to either pole is 90o (north or south) with 0o being the
clearance, and weather minimums, the controller should be advised and a equator, north
revised clearance or instruction obtained.

Longitude lines are called meridians and are drawn from pole to pole at
Emergency Locator Transmitter (ELT) right angles to the equator.
The prime meridian is used as the zero degree line, passes through Greenwich
Emergency Locator Transmitters (ELT) have been developed as a means of locating
England
downed aircraft
Transmitting on 121.5 and 406 MHz, the ELT will operate continuously for at least from this line measurements are made in degrees easterly or westerly
48 hours 180o

To prevent false alarms the ELT should be tested only during the first 5 minutes of
any hour and only for one to three sweeps. Washington DC is about 39o north of the equator and 77o west of the prime meridian
False alarms can also be minimized by monitoring 121.5 or 406 prior to engine and would be: 39oN 77oW
shutdown at the end of each flight
latitude is stated first
Non-rechargeable batteries used in ELTs must be replaced when 50% of their useful
life has expired, or when the transmitter has been in use for more than 1 In order to describe a location more precisely each degree (o) is subdivided
cumulative hour. into 60 minutes (') and each minute is further divided into 60 seconds ("),
although seconds are not shown.
Enroute Flight
The location (in Oklahoma) can be 35o25'55"N 99o23'15"W
Pilotage
Degrees of west longitude increase from east to west
Air navigation is the art of directing an aircraft along a desired course and being Degrees of north latitude increase from south to north
able to determine its geographical position at any time. Such navigation may be
accomplished by pilotage, dead reckoning, or using radio navigational aids.
 Topography
A VFR Sectional Aeronautical Chart is a pectoral representation of a portion of the
Earth's surface upon which lines and symbols in a variety of colors represent
features and/or details that can be seen on the Earth's surface.

Contour lines, shaded relief, color tints, obstruction symbols, and maximum
elevation figures are all used to show topographical information.

Dead Reckoning
Dead reckoning is the method used for determining position with a heading indicator
and calculations based on speed, elapsed time, and wind effect from a known
position.
The instruments used for dead reckoning navigation include the outside air
Time temperature gauge, the airspeed indicator, the altimeter, the clock, and the
magnetic compass system of slaved gyro system.
Time is measured in relation to the rotation of the earth. A day is defined as the
These instruments provide information concerning direction , airspeed, altitude,
time required for the earth to make one complete revolution of 360o. Since the day
and time and must be correctly interpreted for successful navigation.
is divided into 24 hours, the earth revolves at the rate of 15o each hour.
Thus longitude may be expressed as either 90o or 6 hours west of Greenwich Plotting Course
Twenty-four time zones have been established. Each time zone is 15o of A course is the direction of flight measured in degreed clockwise from north.
longitude in width, with the first zone centered on the meridian of Greenwich. Meridians of longitude run from the south pole to the north pole. This alignment is
Each zone uses the local time of its central meridian called true north.

When a course is plotted on a chart in relation to the lines of longitude

and/or latitude it is called a True Course (TC) and will be expressed in three
digits
North may be either 360o or 000o
East is 090o
South is 180o
West 270o

Any attempt to project lines of latitude and longitude onto a flat surface such as
A course measured on a sectional chart is a true course:
a chart results in a certain amount of distortion.
it is measured from a meridian, which runs from the south pole to the
When plotting a course on a sectional aeronautical chart, this distortion north pole.
may be minimized by measuring true course in reference to the meridian Since a magnetic compass is used to maintain a course while flying,
nearest to the halfway point between the departure and the destination. this true course must now be converted to a magnetic course.
This conversion is made by either adding or subtracting the
The straight edge of the plotter has distance scales that match various charts and variation
these scales may depict both statute and nautical mils. To convert a true course to a magnetic course, subtract easterly
A small hole at the base of the protractor portion indicates the center of the arc variation, and add westerly variation: "East is least, west is best"
of the angular scale.
Two complete scales cover the outer edge of the protractor, they are graduated in True course +/- Variation = Magnetic Course +/- Deviation = compass course
degrees.
An inner scale measure the angle from the vertical. Wind and Its Effects
An additional computation, common to both pilotage and dead reckoning, is necessary
To determine true course (TC), use the plotter in the following manner:
to compensate for the effect of wind.
5.1. Using the straight edge of the plotter as a guide, draw a line from the
point of departure to the destination Wind direction is reported as the direction from which the wind blows
5.2. Place the top straight edge of the plotter parallel to the plotted
Wind blowing from the west to the east is a west wind
course and move the plotter along the course line as necessary to place
Wind speed is the rate of motion without regard to direction
the small center hole over a meridian as near to the halfway point of the
course as possible.
Downwind movement is with the wind
5.3. The true course is the angle measured between the meridian and the
course line Upwind movementis against the wind
the outer scale is used to read all angles between north through
east to south, and the inner scale is used to read all angles between If a powered aircraft is flying in a 20-knot wind, it will move 20 nautical
south through west to north. miles downwind in 1 hour in addition to its forward movement through the
air.
5.4. Course lines which fall within 30o of true north or south can be more
easily measured by sliding the plotter along the course line until the
hole falls over a horizontal latitude line; use the partial protractor The sideward displacement of an aircraft caused by wind is called drift.
scale for these measurement
Drift can be determined by measuring the angle between the heading(the
direction the nose is pointing) and the track(the actual flight path of the
Magnetic Variation aircraft over the earth)

The north pole where all meridians converge is true north.

These two poles are not in the same place. At any point where magnetic north and
true north are in line with each other, the compass needle points both to magnetic
north and coincidently true north.
The line along which this occurs is known as the agonic line.
When positioned west of agonic line, a compass will pint left(west) of true north.
This angular difference between true north and magnetic north is called magnetic
variation (VAR). West of the agonic line, variation is "easterly" East of the
agonic line, variation is "westerly"

The amount of variation is depicted on sectional charts as dashed magenta colored

line connecting points of equal variation called isogonic lines
 Wind Triangle
True course is determined by measuring the course on an aeronautical chart.

True airspeed is known by applying the appropriate correction to the indication of

the indication of the airspeed indicator.

Wind direction and velocity are known from reports or forecasts from the Flight
Service Stations

The true heading and the ground speed can be found by drawing a wind triangle of
vectors.

One side of the triangle is the wind direction and velocity

One side of the triangle is the true heading and true airspeed
The final side is the track, or true course, and the ground speed
Each side of a wind triangle is the vector sum of the other two sides

Any course, true, magnetic, or compass, becomes a heading when it is corrected for
wind:
Flight Computer (E6-B)
 Flight Instruments
Pitot-Static Instruments
The pressure altimeter, vertical-speed indicator, and airspeed indicator operate in
response to pressures through the pitot-static system

Airspeeds and the Airspeed Indicator

Static (atmospheric) pressure is taken from the static vents and is

provided to all three instruments
clogging of the static vents or line will cause all three
instruments to become inoperative or to display erroneous readings
Impact (ram) pressure is taken from the pitot tube and furnished to
the airspeed indicator only
clogging of the pitot opening will not affect the operation of the
altimeter or vertical speed indicator
 A number of airspeed limitation abbreviated "V" speeds are indicated by
color-coded marking in the airspeed indicator:

VSO: stall speed or minimum steady flight speed in the landing

configuration (the lower limit of the white arc)
VFE: maximum flap extended speed (upper limit of the white arc). The
entire white arc defines the flap operating range
VS1: the stall speed or minimum steady flight speed in s specified
configuration (lower limit of the green arc). The entire green arc
defines the normal operating range
VNO: the maximum structural cruising speed (the upper limit of the
green arc and lower limit of the yellow arc). The yellow arc defines the
caution range, which should be avoided unless in smooth air
VNE: never exceed speed (the upper limit of the yellow arc) marked in
red
VLE: the maximum landing gear extended speed
VA: the design maneuvering speed. If rough air or sever turbulence is
encountered, airspeed should be reduced to maneuvering speed or less to
minimize stress on the airplane structure
VY: the best rate-of-climb speed (the airspeed that will result in the
most altitude in a given period)
VX: the best angle-of-climb speed (the airspeed that will result in the
most altitude in a given distance)

The Altimeter and Altitudes

The altimeter is an instrument used to measure height (altitude) by responding to
atmospheric pressure changes

Altitude: elevation with respect to any assumed reference level and different
term identify the reference level used
Indicated altitude: the altitude read on the altimeter after it is set to the
Indicated Airspeed ( IAS ): the uncontrolled reading obtained from the airspeed current local altimeter setting
indicator Absolute altitude: the height above the surface
Calibrated Airspeed ( CAS ): indicated airspeed corrected for installation and True altitude: the true height above Mean Sea Level (MSL)
instrument error Pressure altitude: the altitude that is indicated whenever the altitude
True Airspeed ( TAS ): calibrated airspeed corrected for temperature and setting dial is adjusted to 29.92 The Standard Datum Plane, may be above, at or
pressure variations below sea level
White arc: flap operating range. Lower limit represents full flap stall Density altitude: the pressure altitude corrected for nonstandard temperature
speed. Upper limit provides maximum flap speed. Approaches and landings at and/or pressure
speeds in white arc rotating the setting knob on the altimeter simultaneously rotates the
Green arc: normal operating range setting dial and the altimeter hands at a rate of one inch per 1000 feet of
Yellow arc: caution range altitude.
Red line: never-exceed speed increasing the setting dial from 29.15 to 29.85 would cause the hands of
the altimeter to show an increase of 700 feet

Prior to takeoff the altimeter should be set to the current local

altimeter setting.
After takeoff the altimeter should remain set to the current local
altimeter setting until climbing through 18,000 feet MSL, at that time
the altimeter should be set to 29.92
To compensate for the effect of nonstandard conditions, the altimeter
must be set to the altimeter setting of a station within 100 NM of the
aircraft (unless above 18,000 MSL)
 When turning toward north from an easterly or westerly heading, the compass
lags behind the actual aircraft heading

Gyroscopic Instruments
When a turn is initiated while on a northerly heading the compass first
Attitude Indicator indicates a turn in the opposite direction.
The compass lags whenever turns are made to or from north
The attitude indicator is uses to reference the aircrafts pitch and bank against an
artificial horizon
When turning toward south from an easterly or westerly heading the compass
Turn Coordinator leads the actual aircraft heading

The turn coordinator uses a miniature airplane to provide information concerning

When a turn is initiated while on a southerly heading the compass shows an
the rate of roll and rate of turn
immediate lead in the same direction as the turn. The compass leads whenever
Simultaneously the quality of turn, or movement about the yaw axis, is indicated by turns are made to or from south
the ball of the inclinometer
When accelerating or decelerating while heading either east or west the
Heading indicator compass will indicate a turn north
While decelerating it will indicate a turn south
The heading indicator (HI) (directional gyro DGH) informs the pilot of the
aircrafts heading
Navigation
The heading indicator must be periodically realigned with the magnetic compass
during straight-and-level unaccelerated flight VHF Omnidirectional Range (VOR)
Magnetic Compass The VOR is the backbone of the National Airway system, and this radio aid to
navigation (NAVAID) provides guidance to pilots operating under VFR as well as IFR.
The magnetic compass is attracted to a magnetic field in the earth, so it point
down as well as north. This downward pointing tendency is called magnetic dip and
causes errors in compass indications

On sectional aeronautical charts, VOR location are shown by blue symbols

centered in a blue compass rose which is orientated to Magnetic North.

A blue identification box adjacent to the VOR symbol lists the name
and the frequency of the facility, its 3-letter identifier and Morse Code
equivalent, and other appropriate information

Some VORs have a voice identification alternating with the Morse Code
identifier.
absence of the identifier indicated the facility is unreliable or
undergoing routine maintenance
in either case it should not be used for navigation
Sone VORs also transmit a T-E-S-T code when undergoing maintenance
The VOR station continuously transmits navigation signals providing 360
magnetic courses to to radials from the station.
courses are TO the station and radials are FROM the station
TACAN, a military system which provides directional guidance, also informs
the pilot of the aircrafts distance from the TACAN station
When a VOR and a TACAN are co-located, the facility is called a VORTAC.
Civil pilots may receive both azimuth and distance information from a
VORTAC
At some VOR sites additional equipment has been installed to provide pilots
with distance information
such an installation is called VOR/DME (distance measuring equipment)

VOR Orientation
The Omni Bearing Selector (OBS) is an azimuth dial which can be rotated to select a
course or to determine which radial the aircraft is on.

The TO/FROM indicator shows whether flying the selected course would take
the aircraft to or from the VOR station

A TO indication shows the radial selected is on the far side of the

VOR station
A FROM indication means the aircraft and the selected course are on
the same side

The Course Deviation Indicator (CDI) when centered, indicated the aircraft is on
the selected course, or, when not centered, whether that course is to the left or
right of the aircraft.
 The following indicates that a course of 030o would take the aircraft to the To determine position in relation to one or more VOR stations:
selected station, and to get on that course, the aircraft would have to fly
5.1. tune and identify the selected station.
to the left of 030o
5.2. rotate the OBS until the CDI centers with a from indication
5.3. the OBS reading is the magnetic course from the VOR station to the
aircraft
5.4. Repeat the procedure using a second VOR: the aircraft is located at the
point where the two lines of position cross

Course Determination
To determine the course to be flown to a VOR station on the sectional chart, first
draw a line from the starting point to the VOR symbol in the center of the compass
rose.
At the point where the course line crosses the compass rose, read the radial
The course to the station is the reciprocal of that radial

Without RAIM capability, the pilot has no assurance of the accuracy of the GPS
position.
If RAIM is not available, another approach system must be used, another destination
selected, or the trip delayed until RAIM is predicted to be available on arrival.

Procedures and Airport Operations

Uncontrolled and Tower-Controlled Airports
Air Traffic Control Towers (ATCT) are established to promote the safe orderly, and
expeditious flow of air traffic.

VOR Airways The tower controller will issue instructions for aircraft to follow the
desired flight path while in the airport traffic area whenever necessary by
The routes established between VORs are depicted by blue-tinted bands showing the using terminology:
airway number following the letter "V" and are a called Victor airways

When approaching a VOR where airways converge a pilot must exercise extreme
vigilance for other aircraft
In addition when climbing or descending VFR on an airway, it is considered good
operating practice to execute gentle banks left and right for continuous visual
scanning of the airspace

VOR Receiver Check Points

VOR receiver accuracy may be checked by means of a VOR Test Facility (VOT), ground
check points, or airborne check points

VOTs transmit only the 360o radial signal. Thus when the OBS is set to 360o, the
CDI will center with a FROM indication; while the reciprocal 180o will cause the
CDI to center with a TO indication
An accuracy factor of +/- 4o is allowed when using a VOT facility

Global Positioning System (GPS)

GPS is a United States satellite-based radio navigational, positioning, and time The ATCT will also direct aircraft taxing on the surface movement area of the
transfer system operated by the DOD. airport.

The system provides highly accurate position and velocity information and precise In all instances, an appropriate clearance must be received from the tower
time on a continuous global basis to an unlimited number of properly-quipped user. before taking off or landing.

The GPS constellation of satellites is designed so that a minimum of five are At airports without an operating control tower, pilots of fixed-wing and weight
always observable by a user anywhere on earth. shift control aircraft must circle the airport to the left ("left traffic") unless
The GPS receiver uses data from a minimum of four satellites to yield a three visual indicators indicate right traffic
dimensional position (latitude, longitude, and altitude) and time solution

The GPS receiver verifies the integrity (usability) of the signals received from
the GPS satellites through receiver autonomous integrity monitoring (RAIM) to
determine if a satellite is providing corrupted information.
 A common visual indicator is the segmented circle system, which consists of
the following components:

Segmented Circle: located in a position readily visible to pilots in

the air and on the ground
Tetrahedron: may be used to indicate the direction of landings and
takeoff. The small end of the tetrahedron points in the direction of
landing.
pilots are cautioned against using the tetrahedron to determine
wind direction, because it may not indicate the correct direction in
light winds
Wind cone, wind sock, wind tree: may be installed near the operation
runway to indicate wind direction.
the large end of the wind cone or sock points into the wind, as
does the cross bar of the wind tee

The tetrahedron, wind cone, wind sock or wind tee may be located in the
center of the segmented circle and may be lit for night operations
landing runway (landing strip) indicators are installed in pairs and used to
show alignment of runways
traffic pattern indicators are installed in pairs in conjunction with
landing strip indicators and are used to indicate the direction of turns

For example , an azimuth of 183o would result in a runway number of 18, a

magnetic azimuth of 076o would result in runway 8
Runway letters differentiate between left (L), right(R), center(C)

The designated beginning of the runway that is available and suitable for
the landing of an aircraft is called the threshold:

A threshold that is not at the beginning of the full-strength runway

pavement is a displaced threshold
The paved area behind the displaced threshold is marked by arrows and
is available for taxiing, takeoff, and landing rollout, but is not to be
used for landing (usually because of an obstruction in the approach path)

Airport Markings
Runway numbers and letters are determined from the approach direction.
The number is the magnetic heading of the runway rounded to the nearest 10o

Stopways are found extending beyond some usable runways.

 these areas are marked by chevrons, and while they appear usable, they
are suitable only as overrun areas
A closed runway which is unusable and may be hazardous, even though it may
appear usable, will be marked by an " X "

LAHSO is an acronym for " Land And Hold Short Operation ".

These operations include landing and holding short of an intersecting runway,

intersecting taxiway, or some other designated point on a runway or taxiway
LAHSO is an ATC procedure that requires pilot participation to balance the
needs for increased airport capacity and system efficiency, consistent with
safety.
Student pilots or pilots not familiar with the LAHSO should not participate
in the program
The pilot in command has final authority to accept or decline any land
and hold short clearance.
The safety and operation of the aircraft remain the responsibility of the
pilot
pilots are expected to decline a LAHSO clearance if they determine it
will compromise safety.
Available Landing Distance (ALD) data are published in the special notices
section of the Chart Supplements U.S. and in the U.S. Terminal Procedures
Publications.
Airport Lighting
Pilots should only receive LAHSO clearance when there is a minimum
ceiling of 1,000ft and 3 statute miles visibility. At night the location of an airport can be determined by the presence of an airport
The intent of having basic VFR weather conditions is to allow pilots rotating beacon light. The colors and color combinations that denote the type of
to maintain visual contact with other aircraft and ground vehicle airports are:
operation

Radio Control of Lighting is available at some airports, providing airborne

control of lights by keying the aircrafts microphone. The control system is
responsive to the following microphone clicks:

low intensity: 3 times in 5 seconds

medium intensity: 5 times in 5 seconds
highest intensity: 7 times in 5 seconds

Visual Approach Slope Indicator (VASI)

The Visual Approach Slope Indicator (VASI) is a lighting system arranged so as to
provide visual descent guidance information during an approach to a runway.

The lights are visible for up to 5 miles during the day.

The VASI glide path provides obstruction clearance, while lateral guidance is
provided by the runway or runway lights
When operating to an airport with an operating control tower, the pilot of
the airplane approaching to land on a runway served by a VASI is required to
maintain an altitude at or above the glide slope until a lower altitude is
necessary for landing.

In class B, C, D, or E airspace, operation of the airport beacon during the hours

of daylight often indicates the ceiling is less than 1,00 feet and/or the
visibility is less than 3 miles:

however pilots should not rely solely on the operation of the airport beacon
to indicate if weather conditions are VFR or IFR

Runway Edge Lights are used to outline the runway at night or during periods
of low visibility. For the most part runway edge lights are white, and may
be high, medium, or low-intensity while taxiways are outlined by blue Pulsating Visual Approach Slope Indicator (PVASI)
omnidirectional lights
Pulsing VASIs normally consist of a single light unit projecting a two-color visual
approach path.

Below-glide path indication is normally red or pulsating red

Above-glide path is normally pulsating white
On-glide path is normally steady white
Precision Approach Path Indicator (PAPI)

The PAPI uses a single row of lights:

Surface Operations
Taxing to or from the runway generally presents no problems during calm or light
wind conditions.
However , when taxing in moderate to strong wind conditions, the airplane's control
surfaces must be user to counteract the effects of wind. In airplanes equipped with
nose wheel (tricycle-gear), use the following taxi procedures:

1. The elevator should be in the neutral position

2. The upwind aileron should be held in the up position when taxiing in a cross
wind (or the upwind wing will tend to lift)
3. The elevator should be held in the down position and the upwind aileron down
when taxiing with a quartering tailwind

When an airplane equipped with a tailwheel is taxied into a headwind, the elevator
should be held in the up position to hold the tail down.
In a quartering tailwind, both the upwind aileron and the elevator should be in the
down position.

Chart Supplements U.S. (previously A/FD)

The chart supplements U.S. is a publication designed primarily as a pilots
operational manual containing all airports, seaplane bases, and heliports open to
the public including communications data, navigational facilities, and certain
special notices and procedures

Directories are reissued in their entirety each 56 days

Fitness for Flight Carbon Monoxide Poisoning: Carbon monoxide is a colorless, odorless, and
tasteless gas contained in exhaust fumes.
Pilot performance can be seriously degraded by a number of physiological factors.
While some of the factors may be beyond the control of the pilot, awareness of Symptoms of carbon monoxide poisoning include headache, drowsiness, or
cause and effect can help minimize any adverse effects. dizziness.
large accumulations of carbon monoxide in the human body result in a
Hypoxia: a state of oxygen deficiency, impairs functions of the brain and loss of muscular power
other organs. Headache, drowsiness, dizziness, and euphoria are all symptoms susceptibility increases as altitude increases
of hypoxia A pilot who detects symptoms of carbon monoxide poisoning should
immediately shut off the heater and open the air vents
For optimum protection pilots should avoid flying above 10,000ft MSL
for prolonged periods without using supplemental oxygen. Various complex motions, forces, and visual scenes encountered in flight may result
Federal Aviation Regulations require that when operating an aircraft in misleading information being sent to the brain by various sensory organs.
at cabin pressure altitudes above 12,500ft MSL up to and including
Spatial disorientation may result if these body signals are used to interpret
14,000ft MSL , supplemental oxygen shall be used by the minimum flight
flight attitude.
crew during that time in excess of 30 minutes at those altitudes
The best way to overcome spatial disorientation is by relying on the flight
Every occupant of the aircraft must be provided with supplemental
instruments rather than taking a chance on the sensory organs.
oxygen above 15,000ft

Aeronautical Decision Making

Aviation-breathing oxygen should be used to replenish an aircraft oxygen system for
high-altitude flight. The pilot is responsible for determining whether they are fit to fly for a
Oxygen used for medical purposes or welding normally should not be used because it particular flight.
may contain too much water. The excess water could condense and freeze in oxygen Most preventable accidents have one common factor: human error, rather than a
lines when flying at high altitudes. This could block oxygen flow. Also , constant mechanical malfunction.
use of oxygen containing too much water may cause corrosion in the system Good aeronautical decision making (ADM) is necessary to prevent human error.
ADM is a systematic approach to the mental process used by aircraft pilots to
Specifications for "aviators breathing oxygen" are 99.5% pure oxygen, and not
consistently determine the best course of action in response to a given set of
more than 0.005 mg of water per liter of oxygen
circumstances.

Hyperventilation: a deficiency of carbon dioxide within the body, can be the The ADM process address all aspects of decision making in the cockpit and
result of rapid or extra deep breathing due to emotional tension or anxiety identifies the steps involved in good decision making:
or fear.
1. Identifying personal attitudes hazardous to safe flight
Symptoms will subside after the rate and depth of breathing are 2. Learning behavior modification techniques
brought under control.
3. Learning how to recognize and cope with stress
A pilot should be able to overcome the symptoms or avoid future
4. Developing risk assessment skills
occurrences of hyperventilation by talking aloud, breathing into a bag,
or slowing the breathing rate 5. Using all resources in a multicrew situation
6. Evaluating the effectiveness of ones ADM skills

Dangerous Tendencies

Peer Pressure: poor decision making basked upon emotional response to peers
rather than evaluating a situation objectively

Mind Set: the inability to recognize and cope with changes in the situation
different from those anticipated or planned
 Get-There-Itis: this tendency, common among pilots, clouds the vision and Neglect of Flight Planning, Preflight Inspections, Checklists, etc:
impairs judgement by causing a fixation on the original goal or destination Unjustified reliance on the pilot's short and long term memory, regular
combined with a total disregard for any alternative course of action flying skills, repetitive and familiar routes, etc.

Duck-Under Syndrome: The tendency to sneak a peak by descending below

minimums during an approach

Based on the belief that there is always a built in "fudge" factor

that can be used or on an unwillingness to admit defeat and shoot a
missed approach

Scud Running: Pushing the capabilities of the pilot and the aircraft to the
limits by trying to maintain visual contact with terrain while trying to
avoid physical contact with it

This attitude is characterized by the old pilots joke "if its too bad
to go IFR we'll go VFR

Continuing Visual Rules (VFR): into instrument conditions often leads to

Each ADM student should take the Self-Assessment Hazardous Attitude Inventory Test
spatial disorientation of collision with ground/obstacles.
in order to gain a realistic perspective on their attitudes toward flying.
It is even more dangerous if the pilot is not an instrument qualified or
The inventory test requires the pilot to provide a response which most accurately
current
reflects the reasoning behind their decision

Getting Behind the Aircraft: Allowing events or the situation to control The pilot must choose one of the five reasons given for making a decision, even
your actions rather than the other way around though the pilot may not consider any of the five choices acceptable.
The inventory test presents extreme cases of incorrect pilot decision making in an
Characterized by a constant state of surprise at what happens next effort to introduce the five types of hazard attitudes:

1. Antiauthority (don't tell me): This attitude is found in people who do not like
Loss of Positional or Situational Awareness: Another case of getting behind
anyone telling them what to do. The attitude for this attitude is Follow the
the aircraft which results in not knowing where you are, an inability to
rules, they are usually right.
recognize deteriorating circumstances, and/or the misjudgment of the rate of
2. Impulsivity (do something quickly): Is the attitude of people who frequently
deterioration
feel the need to do something "anything" immediately. The antidote for this
attitude is Not so fast. Think first.
Operating Without Adequate Fuel Reserve: Ignoring minimum fuel reserve 3. Invulnerability (it won't happen to me): Many people feel that accident happen
requirements, either VFR or IFR, is generally the result of overconfidence, to others, but never to them. The antidote for this attitude is It could happen
lack of flight planning, or ignoring the regulations to me
4. Macho (I can do it): Pilots who are always trying to prove that they are better
than anyone else. The antidote for this attitude is Taking chances is foolish
Descent Below the Minimum Enroute Altitude: The duck-under syndrome
manifesting itself during the enroute portion of an IFR flight 5. Resignation (What's the use): Pilots who think "what's the use?" do not see
themselves as being able to make a great deal of difference in what happens to
them. The antidote for this attitude is I'm not helpless, I can make a
Flying Outside the Envelope: Unjustified reliance on the (usually mistaken) difference
belief that the aircraft's high performance capability meets the demands
imposed by the pilots (usually overestimated) flying skills Hazardous attitudes which contribute to poor pilot judgement can be effectively
counteracted by redirecting that hazardous attitude so that appropriate action can
be taken.
When a pilot recognizes a thought as hazardous, the pilot should label that thought
Scanning the sky for other aircraft is a key factor in collision avoidance.
as hazardous, then correct that thought by stating the corresponding antidote
Because the eyes focus only on a narrow viewing area, effective
Good cockpit stress management begins with a good life stress management. The scanning is accomplished with a series of short, regularly spaced eye
following checklist outlines some thoughts on cockpit stress management: movements

1. Avoid situations that distract you from flying the aircraft Each movement should not exceed 10o and each area should be observed
for at least 1 second.
2. Reduce your workload to reduce stress levels. This will create a proper
environment in which to make good decisions At night, scan slowly to permit the use of off-center vision

3. If an emergency does occur, be calm. Think for a moment, weigh the

Prior to starting any maneuver, a pilot should visually scan the entire area for
alternatives, then act
collision avoidance.
4. Maintain proficiency in your aircraft; proficiency builds confidence.
Familiarize yourself thoroughly with your aircraft, its systems and emergency Any aircraft that appears to have no relative motion and stays in one scan quadrant
procedures
is likely to be on a collision course.
5. Know and respect your own personal limitations
6. Do not let little mistakes bother you until they build into a big thing. Wait If a target shows neither lateral nor vertical motion, but increases in size, take
until after you land, then "debrief" and analyze past actions evasive action.
7. If flying is adding to your stress either stop flying or seek professional help
When climbing or descending VFR on an airway, execute gentle banks, right and left
to manage stress.
to provide for visual scanning of the airspace
DECIDE Model
Aircraft Lighting
The DECIDE model is intended to provide the pilot with a logical way of approaching
When an aircraft is being operated during period from sunset to sunrise (except in
decision making:
Alaska) it must display lighted position lights and anti-collision lights.
1. Detect that a change has occurred
The anti-collision light may be either aviation red or aviation white
2. Estimate what is needed to counter or react to the change
3. Choose a desirable outcome (in terms of success) for the flight
4. Identify actions which could successfully control the change
5. Do the necessary action
6. Evaluate the effect(s) of the action countering the change

Collision Avoidance
Vision is the most important body sense for safe flight.
Major factors that determine how effectively vision can be used are the level of
illumination, and the technique of scanning the sky for other aircraft.

Atmospheric Haze reduces the ability to see traffic or terrain during

flight, making all features appear to be farther away than they actually are

In preparation for night flight, the pilot should avoid bright while lights for at
least 30 minutes before the flight
 Regulations
14 CFR Part 1: definitions and abbreviations of many terms commonly used in
aviation
night means the time between the end of evening civil twilight and the
beginning of morning civil twilight
14 CFR Part 61: Certification: pilots, flight instructors and ground
instructors
prescribes requirements for issuing pilot and and flight instructor
certificates and ratings, the conditions of issue, and the privileges and
limitations of those certifications
14 CFR Part 91: General Operating and Flight Rules
describes rules governing the operation of aircraft within the US
The National Transportation Safety Board (NTSB) has established rules and
requirements for notification and reporting of aircraft accidents and
incidents.
NTSB Part 830

The definition of nighttime is the time between the end of civil twilight and the
beginning of morning civil twilight.

Pilot Certificate Privileges and Limitations Medical Certificates

The holder of a student pilot certificate is limited to solo flights or
flights with an instructor
A private pilot has limited solo privileges, and may carry passengers or
cargo as long as the flying is for the pilots pleasure or personal business and
is not done for hire
A private pilot may not pay less than the pro rata share of the operating
expenses of a flight with passengers, provided the expenses only involve fuel,
oil, airport expenditures, or rental fees
the only time passengers may pay for the entire flight is is a donation
is made by the passengers to the charitable organization which is sponsoring
the flight
Commercial pilots may fly for compensation or hire
Airline Transport Pilot may act as pilot-in-command of airline and scheduled
commuter operations
All pilot certificates are valid unless surrendered, superseded or revoked

Pilot Ratings
Category: a broad classification of aircraft such as airplane, rotorcraft,
glider, and lighter-than-air
Class: classification within a category
single-engine, multi-engine, land, water
Type: specific make and basic model of aircraft
a type rating must be held by the pilot in command of large aircraft; Basic med - if you have previously held a medical certificate that was not
more than 12,500 pounds maximum takeoff weight suspended, revoked, or withdrawn a pilot can act as PIC for noncommercial flights
all turbojet-powered airplanes require PIC to have a type rating with a drivers license. Must complete CMEC within 24 months and physical within
For IFR an instrument rating is required last 48 months. When operating under BasicMed, pilots are limited to:

fly with no more than 5 passengers

fly an aircraft with a maximum certified takeoff weight of no more than 6,000
lbs
fly an aircraft that is authorized to carry no more than 6 occupants
flights within the US at an indicated airspeed of 250 knots or less, and at
an altitude at or below 18,000 feet mean sea level (MSL)
may not fly for compensation or hire
 Second class medical may exercise the commercial privileges during the first (6 or
12 months) calendar months, and private pilot privilege during the following (12 or
48) months

First class medical may exercise ATP privileges (first class) 6 or 12 months, 12
months from the date of the examination with second class, and 2 or 5 years with
third class

Required Certificates
When acting pilot-in-command a pilot must have in their possession ore readily
accessible in the aircraft:

current pilot license

photo ID
current medical certificate

A pilot must present their pilot license and medical for inspection upon request of
any FAA, NTSB, or federal, state, or local law enforcement officer

Recent Flight Experience

No person may act as PIC of an aircraft unless within the preceding 24 calendar
months they have accomplished a flight review

Flight Review: This review is given in an aircraft for which the pilot is
rated by an appropriately rated instructor or other person designated by the
FAA.

A logbook entry will document satisfactory accomplishment of this

requirement.
If the pilot takes a proficiency check (as for a certificate or a new
rating) is counts for the flight review

No person may act as PIC of an aircraft carrying passengers unless

within the preceding 90 days they have made 3 takeoffs and 3 landings as
the sole manipulator of the controls in an aircraft of the same category,
class, and if a type rating is required in the same type
touch and go landings are acceptable unless the passengers are to
be carried in a tailwheel airplane, in which case the landing must
come to a full stop
Third-Class Medical expires at the end of: If passengers are to be carried during the period from 1 hour after
sunset to 1 hour before sunrise, the PIC must have made within the
The 60th month after the month of the date of the examination shown on the preceding 90 days, at least 3 takeoffs and 3 landings during that period.
certificate if the person has not reached his/her 40th birthday on or before The landing must have been to a full stop and in the same category and
the date of the examination class of aircraft to be used
The 24th month after the month of the date of examination shown on the
certificate if the per has reach their 40th birthday

High-Performance Airplanes fuel requirements

enough fuel to fly to the first point of intended landing, and at normal
No person holding a Private or Commercial Pilot Certificate may act as PIC of an cruising speed, to fly after that for at least 30 minutes if during the day,
airplane that has more than 200 horsepower's, unless they have received instruction or for at least 45 minutes at night
from an authorized flight instructor who has certified in their logbook that they alternatives available if the flight cannot be completed as planned
are competent to pilot a high-performance airplane
Seatbelts
Glider Towing
All required flight crewmembers must remain in their seats with seatbelts
A private pilot may not act as PIC of an aircraft towing a glider unless at least
secured during the entire flight unless absent in connection with duties or
100 hours of pilot flight time is logged in the aircraft category, class and type
physiological needs. When shoulder harnesses are installed they must be used
or 200 hours total pilot time
during takeoffs and landings
also within the preceding 24 months they have made at 3 actual/simulated
glider tows while accompanied by a qualified pilot or has made 3 flights as PIC Prior to takeoff, the PIC must ensure that each person on board has been briefed on
of a towed glider the use of seatbelts.

In addition they must ensure that the passengers are notified to fasten their
Change of Address
seatbelts during taxi, takeoffs, and landings. A child who has not reached their
If a pilot changes their permanent mailing address without notifying the FAA second birthday may be held by an adult who is occupying a seat or berth
Airmens Certification Branch, in writing within 30 days, then they may not exercise
the privileges of their certificate Alcohol and Drugs
No person may act as a crewmember on an aircraft under the following conditions:
Responsibility and Authority of the Pilot-in-Command
Within 8 hours after the consumption of any alcoholic beverage
The PIC of an aircraft is directly responsible and is the final authority for the
While under the influence of alcohol (0.04 percent by weight or more alcohol
safety and operation of that aircraft.
in the blood)
Should an emergency require immediate action, the PIC may deviate from 14 CFR Part While using any drug that affects their faculties in any way contrary to
91 to the extent necessary in the interest of safety. safety

upon request a written report of any deviation from the rules must be sent to Except in an emergency, no pilot of an aircraft may allow a person who
the Administrator appears to be intoxicated or under the influence of drugs (except a medical
patient under proper care) to be carried in that aircraft
If a pilot receives a clearance that would cause a deviation from a rule,
they should query the controller and request that the clearance be amended A conviction for the violation of any law relating to drugs or alcohol is grounds
for:
Preflight Action
1. Denial of an application for any certificate, rating, or authorization issued
Before beginning a flight the PIC is required to become familiar with all available under part 61 for a period of up to 1 year after the date of final conviction
information concerning that flight. This information must include the following: 2. Suspension or revocation of any certificate, rating, or authorization issued
under Part 61
Runway lengths Pilots should provide a written report of each alcohol-or-drug-related motor
Takeoff and landing information for airports of intended use, including vehicle action to the FAA, Civil Aviation Security Division (AMC-700) no later
aircraft performance data than 60 days after the motor vehicle action

If the flight will not be in the vicinity of the departure airport, the pilot must
also consider the following:

weather reports and forecasts

Right-of-Way Rules
When weather conditions permit, vigilance must be maintained so as to see and avoid
other aircraft.

An aircraft in distress has the right-of-way over all other air traffic.
When aircraft of the same category are converging at approximately the same
altitude (except head-on, or nearly so) the aircraft on the other's right
has the right-of-way

If the aircraft are of different categories, the following applies:

A balloon has the right-of-way over any other category aircraft

A glider has the right-of-way over an airship, airplane, rotorcraft, weight-
shift control, or powered parachute
An airship has the right of way over an airplane, rotorcraft, weight shift
control or powered parachute

Deviation from Air Traffic Control Instructions

An ATC clearance is authorization for an aircraft to proceed under specified
traffic condition within controlled airspace.

When an ATC clearance has been obtained, no PIC may deviate from that clearance
except in an emergency, unless they obtain an amended clearance.

If a pilot does deviate from a clearance or ATC instruction during an

emergency, they must notify ATC of the deviation as soon as possible
If in an emergency a pilot is given priority over other aircraft by ATC, they
may be requested to submit a detailed report even though no deviation from a
rule occurred
the requested report shall be submitted within 48 hours to the chief of
the ATC facility which granted the priority

Minimum Safe Altitudes

No minimum altitude applies during takeoff or landing.
During the other phases of flight the following minimum altitudes apply:

Anywhere: the pilot must maintain an altitude which, in the event of an

engine failure, will allow an emergency landing without undue hazard to persons
or property on the surface
Over congested areas: an altitude of at least 1,000ft above the highest
obstacle within a horizontal radius of 2,000 feet of the aircraft must be
maintained over any congested area of a city, town or settlement or over any
open air assembly of people
Over other than congested areas: an altitude of 500ft above the surface must
An aircraft towing or refueling other aircraft has the right of way over all other be maintained except over open water or sparsely populated areas.
engine driven aircraft in that case the aircraft may not be operated closer than 500ft to any
person vessel, vehicle, or structure
When aircraft are approaching each other head-on or nearly so, each pilot of each
aircraft (regardless of category) shall alter course to the right

An aircraft being overtaken has the right-of-way. The overtaking aircraft shall
alter course to the right to pass well clear

When two or more aircraft are approaching an airport for landing, the aircraft at
the lower altitude has the right-of-way, but it shall not take advantage of this
rule to cut in front of or overtake another aircraft

Parachutes
If any passengers are carried the pilot of an aircraft may not intentionally exceed
60 degree of bank or 30 degree pitch unless each occupant is wearing an approved
parachute

This requirement does not apply when a CFI is giving instruction in spins or any
other flight maneuver required by regulations for a rating
Basic VFR Weather Minimums
Rules governing flight under Visual Flight Rules (VFR) have been adopted to assist
the pilot in meeting their responsibility to see and avoid other aircraft

In addition, when operating within the lateral boundaries of the surface are
of Class B, C, D, or E airspace designated for an airport, the ceiling must
not be less than 1,000ft.
If the pilot intends to land, take off, or enter a traffic pattern within
such airspace, the ground visibility must be at least 3 miles at that
airport
If ground visibility is not reported, 3 miles flight visibility is required
in the pattern

Special VRF Weather Minimums

If an appropriate ATC clearance (Special VFR) has been received an aircraft may be
operated within the lateral boundaries of the surface area of Class B, C, D, or E
airspace designated for an airport when the ceiling is less than 1,000 ft and/or
the visibility is less than 3 miles

Special VFR requires the aircraft to be operated clear of the clouds with
flight visibility of at least 1 statute mile
For special VFR operating between sunset and sunrise, the pilot must hold an
instrument rating and the airplane must be equipped for instrument flight
Requests for Special VFR arrival or departure clearance should be directed to
the airport traffic control tower if on is in operation

VFR Cruising Altitudes

When operating an aircraft under VFR in level cruising flight more tan 3,000ft
above the surface and below 18,000ft MSL a pilot is required to maintain an
appropriate altitude in accordance with certain rules.

This requirement is called the Hemispherical Cruising Rule and is based on magnetic
course nor magnetic heading.

When operating below 18,000ft MSL in VFR cruising flight with more than
3,000ft above the surface and on a magnetic course of 0o through 179o any odd
thousand-foot MSL altitude plus 500ft (3,500 , 5,500) is appropriate
On a course of 180o through 359o even thousands plus 500ft (4,500, 6,500) is
appropriate

Categories of Aircraft
The term category when used with respect to the certification of aircraft, means a
grouping of aircraft based upon intended use or operating limitation:

normal
utility
aerobatic
restricted
experimental
transport
 limited
provisional

Both restricted and experimental category aircraft are prohibited from carrying
persons or property for compensation or hire.
In addition both categories are normally prohibited from flying over densely
populated areas or in congested airways.

Formation Flight and Dropping Objects

Flying so close to another aircraft as to crate a collision hazard is prohibited.
If the intent is to fly formation, prior to arrangement with the PIC of each
aircraft is required.

In any case, no person may operate an aircraft carrying passengers for in hire in
formation flight.

The PIC of an aircraft may not allow any object to be dropped while in flight
unless reasonable precautions are taken to avoid injury or damage to persons or
property on the surface.

VFR Flight Plans

Although filing a VFR flight plan is not mandatory (except under certain Airworthiness
circumstances) it is considered good operating practice.
Each aircraft is issued an Airworthiness Certificate, which remain valid as long as
The pilot must close a VFR flight plan at the completion of a flight. the aircraft is maintained and operated as required by regulations.
This can be done by contacting the FAA upon landing. This Airworthiness Certificate, along with the Aircraft Registration Certificate,
operating limitation, and weight and balance must be onboard the aircraft during
Speed Limits flight:
The following maximum speed limits for aircraft have been established in the
A irworthiness
interest of safety:
R egistration

1. Below 10,000ft MSL the limit is 250 knots indicated air speed (KIAS) O perating Limitations
W eight and Balance
2. The speed limit within Class B airspace is also 250 KIAS
3. The maximum speed authorized in a VFR corridor through Class Bravo airspace or The aircrafts operating limitations may be found in the airplane flight manual,
in airspace underlying Class B airspace is 200 KIAS approved manual material, markings, and placards, or any combination thereof
4. In class Delta airspace, aircraft are restricted to a maximum of 200 KIAS
5. Unless otherwise authorized or required by ATC, no person may operate an
aircraft at or below 2,500 feet AGL within 4 NM of the primary airport of a
Class C or D airspace area at an indicated airspeed of more than 200 knots

Maintenance and Inspections The transponder cannot be operated unless within the preceding 24 calendar
months it has been inspected and found satisfactory
The owner or operator of an aircraft is primarily responsible for
maintaining that aircraft in an airworthy condition, including compliance If an aircraft has been maintained, rebuilt, or altered in any manner that may have
with airworthiness directives. They are also responsible for all records of appreciably changed its flight characteristics or operation in flight, no
maintenance, repairs and alteration passengers may be carried until it has been flight tested by an appropriately-rated
(The PIC is responsible for determining that the aircraft is in an airworthy pilot (with at least Private Pilot Certificate) and approved for return to service
condition prior to flight)
The airworthiness of an aircraft can be determined by a preflight inspection ADs, ACs, and NOTAMs
and a review of the maintenance records
Airworthiness Directives (AD)
The holder of a pilot certificate is allowed (within certain limits) to
identify unsafe aircraft conditions and prescribe regulatory actions (such
perform preventative maintenance on any aircraft owned and operated by that
as inspection or modification) or limitations under which the affected
pilot.
aircraft may continue to be operated and are mandatory.
Preventative maintenance is limited to tasks such as replacing
Compliance with an applicable Airworthiness Directive must be entered
defective safety wiring, servicing landing gear wheel bearings, replacing
in the appropriate aircraft maintenance records
safety belts, and other tasks listed in 14 CFR Part 43 appendix A
The owner operator is responsible for ensuring ADs are complied with.
After preventative maintenance has been performed on an aircraft the
Pilots may operate an aircraft not in compliance with an AD if the AD
signature, certificate type and certificate number of the person
allows for this
approving the aircraft for return to service, and a description of the
work, must be entered in the aircraft maintenance records
Advisory Circulars
An aircraft may not be operated unless, within the preceding 12 calendar
are issued by the FAA to inform the aviation community in a systematic way
months, it has had an annual inspection and has been approved for return to
of non-regulatory material of interest.
service.
This will be indicated by the appropriate notation in the aircraft In many cases they are the result of a need to fully explain a
maintenance records. particular subject (wake turbulence for example)
To determine the expiration date of the last annual inspection, refer to the They are issued in a numbered-subject system corresponding to the
aircraft maintenance records. subject areas of the Federal Aviation Regulation, Advisory Circulars
(some free, other at cost) may be obtained by ordering from the
If the aircrafts last annual inspection was performed on July 12, 1993 Government Printing Office (GPO)
the next annual inspection will be due no later than midnight, July 31
1994
The Aeronautical Information Manual (AIM) is the official guide to basic
flight information and ATC procedures. It is updated every 180 days and is
If an aircraft is used to carry passengers for hire or used for flight
available from the FAA website
instruction for hire, it must have, in addition to the annual inspection, an
inspection each 100 hours of flight time. (An annual inspection may be
substituted for the 100 hour inspection, but a 100hr inspection may not be
substituted for an annual inspection)

The next 100hr inspection should be performed 100 hours after the
previous inspection was due.
a 100hr inspection was due at 3,302.5 hours on the hobbs meter. The
100-hour inspection was actually done at 3,309.5 hours. The next
100hr inspection is due at 3402.5 hours
 Notices to Airmen (NOTAMs) Accident Reporting Requirements
provide the most current information available. The National Security Board (NTSB) Part 830 contains rules pertaining to
notification and reporting of aircraft accidents and incident.
They provide time-critical information on airports and changes that Is also addresses preservation of aircraft wreckage, mail, cargo, and records.
affect the national airspace system and are of concern to instrument
flight rule (IFR). Accident: means "an occurrence in which any person suffers death, serious
NOTAM information is classified into 4 categories: injury, or in which the aircraft receives substantial damage"
NOTAM (D) or distant
Attached to hourly weather reports and are available at flight Serious Injury: means any injury which:
service stations requires hospitalization for more than 48 hours commencing within 7
Flight Data Center (FDC) NOTAMs days from the date the injury was received
Issued by the National Flight Data Center and contain results in a fracture of any bone (except simple fractures of
regulatory information, such as temporary flight restrictions or fingers, toes, or nose)
an amendment to instrument approach procedures causes sever hemorrhages, nerve, muscle, or tendon damage
pointer NOTAMs involves any internal organ
Highlight or point out another NOTAM such as an FDC or NOTAM involves second or third degree burns or any burns burns affecting
(D) more than 5 percent of the body surface
This type of NOTAM will assist pilots in cross-referencing Substantial Damage: damage or failure which adversely affects the
important information that may not be found under an airport or structural strength, performance, or flight characteristics of the air
NAVAID identifier craft and which would normally require major repair or replacement of the
military NOTAMs affected component
pertain to U.S. Air Force, Army, Marine, and Navy The following is NOT considered substantial damage
NAVAIDs/airports that are part of the NAS engine failure
bent fairings or cowling
NOTAM-Ds and FDC NOTAMS are contained in the Notices to Airment publication which dented skin
is issued every 28 days. Prior to any flight pilots should check for any NOTAMs small punctured holes in the skin or fabric
that could affect their intended flight ground damage to rotor or propeller blades
damage to landing gear, wheels, tires, flaps
An FDC NOTAM will be issued to designate a temporary flight restriction (TFR). engine accessories
The NOTAM will begin with the phrase "Flight Restrictions" followed by the location
brakes
of the temporary restriction, effective time period, area defined in stature miles
wingtips
and altitudes affected.
The NOTAM will also contain the FAA coordination facility and telephone number, the
The term "incident" means "an occurrence other than accident, which affects or
reason for the restriction, and any other information deemed appropriate.
could affect the safety of operation"
The pilot should check the NOTAMs as part of flight planning.
Some of the purposes for establishing a temporary restriction are:
Immediate notification of the NTSB is required when an aircraft accident
protect persons and property in the air or on the surface from an existing or occurs, and any aspect of a specified list of incidents , which include:
imminent hazard
Inability of a flight crewmember to perform their duties due to
provide a safe environment for the operation of disaster relief aircraft
illness or injury
prevent an unsafe congestion of sightseeing aircraft above an incident or
Inflight fire
event, which may generate a high degree of public interest
An aircraft is overdue and believed to have been involved in an
protect declared national disasters for humanitarian reason in Hawaii
accident
protect the President, vice-president, or other public figures
Flight control system malfunction or failure
provide a safe environment for space agency operation
When aircraft collide in flight or damage of more than $25,000 occurs
to property other than the aircraft

The operator of an aircraft involved in an accident or incident which requires

notification of the NTSB is responsible for preserving the wreckage, mail, or cargo
until the NTSB takes custody.
These items may be moved to protect the wreckage from further damage

The operator of an aircraft involved in an accident is required to file an accident

report within 10 days.
A report of an incident must be reported only upon request.

Weather
The Heating of the Earth
The major source of all weather is the sun.

Changes of weather are caused by the unequal heating of the Earth's surface.

The unequal heating of Earths atmosphere creates a large air-cell circulation

pattern (wind) because the warmer air has a tendency to rise (low pressure) and the
colder air has a tendency to settle or descend (high pressure) and replace the
rising warmer air.

This unequal heating, which causes pressure variations will cause variations
in altimeter setting between weather reporting stations

Because the Earth rotates, this large, simple air cell circulation pattern
in greatly distorted by a phenomenon known as Coriolis Force

When the wind first begins to move to higher altitudes, the Coriolis Circulation and Wind
Force deflects it to the right (in the Northern Hemisphere) causing it to
flow parallel to the isobars The general circulation and wind rules in the Northern Hemisphere are as follows:

1. Air circulates in a clockwise direction around a high

2. Air circulates in a counter-clockwise direction around a low
3. The closer the isobars are together, the stronger the windspeed
4. Due to surface friction (up to about 2,000ft AGL), surface winds do not exactly
parallel the isobars. but move outward from the center of the high toward the
low

Knowing that air flows out of the high in a clockwise direction and into the low in
a counter-clockwise direction is useful in preflight planning.
 Moisture can be added to the air by either evaporation or sublimation.
Moisture is removed from the air by either condensation or sublimation

When water vapor condenses on large objects such as airplanes it will form dew and
when it condenses on microscopic particles, clouds or fog forms

Temperature
In aviation temperature is measured in degrees Celsius.

The standard temperature at sea level is 15oC (59oF).

The average decrease in temperature with altitude is 2oC (3.5oF) per 1,000ft.
Since this is an average, the exact value seldom exists
sometimes it even increases (inversion)
the most common ground or surface based temperature inversion is one
that is produced by terrestrial radiation on a clear, relatively still
night.

Moisture
Air has moisture (water vapor) in it.
The water vapor content if air can be expressed in two different ways.

relative humidity
dew point

Relative Humidity relates the actual water vapor present in the air to which
could be present in the air.

Temperature largely determines the maximum amount of water vapor air

can hold
Warm air can hold more water vapor than cold air
Air with 100% relative humidity is said to be saturated, less than
100% is unsaturated

Dew point is the temperature to which air must be cooled to become saturated
by the water already in the air

of the new underlying surface. The air trend toward change is called air mass
modification.

Ridge: an elongated area of high pressure

Trough: an elongated area of low pressure

all fonts lie in troughs

Cold front: is the leading edge of an advancing cold air mass

Warm front: is the leading edge of an advancing warm air mass

Warm fronts move about half as fast as cold fronts

Frontal waves and cyclones (areas of low pressure) usually form on slow-
moving cold fronts or stationary fronts

The physical manifestations of a warm or cold front can be different with each
front.
They vary with the speed of the air mass on the move and the degree of stability of
the air mass being overtaken.
A stable air mass forced aloft will continue to exhibit stable characteristics,
while an unstable air mass forced to ascend will continue to be characterized by
cumulus clouds, turbulence, showery precipitation and good visibility.

Frontal passage will be indicated by the following discontinuities:

4.1. A temperature change

4.2. A continuous decrease in pressure followed by an increase as the front
passes
4.3. A shift in the wind direction, speed or both

Relative humidity can be increased either by lowering the air temperature or by

increasing the amount of moisture in the air.
If the temperature and the dew point spread is small and decreasing condensation is
about to occur.
If the temperature is above freezing, the weather most likely to develop will be
fog or low clouds

Air Masses and Fronts

When a body of air comes to rest on, or moves slowly over, an extensive area having
fairly uniform properties of temperature and moisture, the air takes on these
properties. The area over which the air mass acquires its identifying distribution
of temperature and moisture is its "source region"
As this air mass moves from its source region, it tends to take on the properties
 Clouds
Stability determines which of two types of clouds will be formed: cumuliform or
stratiform

Cumuliform clouds are the billowy-type clouds having considerable vertical

development, which enhances the growth rate of precipitation.
They are formed in unstable conditions, and they produce showery
precipitation made up of large water droplets

Stratiform clouds are the flat more evenly based clouds formed in stable
conditions.
They produce steady continuous light rain and drizzle made up of smaller
raindrops
Stability of the Atmosphere
Steady precipitation (in contrast to showery) preceding a front is an
Atmospheric stability is defined as the resistance of the atmosphere to vertical
indication of stratiform clouds with little or no turbulence
motion.
A stable atmosphere resists any upward or downward movememnt.
Clouds are divided into 4 families according to their height:
An unstable atmosphere allows an upward or downward disturbance to grow into a
vertical (convective) current. low
middle
Determining the stability of the atmosphere requires measuring the difference
high
between the actual existing (ambient) temperature lapse rate of a given parcel of
clouds with extensive vertical development
air and the dry adiabatic lapse rate (3oC per 1,000ft)

A stable layer of air would be associated with a temperature inversion, warming

from below on the other hand, would decrease the stability of an air mass

The first 3 families (low, middle, and high) are further classified
according to the way they are formed:

clouds formed by vertical currents (unstable) are cumulus (heap) and

are billowy in appearance
Clouds formed by the cooling of stable layer are stratus (layered) and
are flat and sheet-like in appearance
A further classification is the prefix "nimbo" or the suffix "nimbus"
which means raincloud

High clouds called cirrus are composed mainly of ice crystals therefore they are
least likely to contribute to structural icing (since it requires water droplets)

The base of a cloud (AGL) that is formed by vertical currents (cumuliform

clouds) can be roughly calculated by dividing the difference between the
surface temperature and dew point by 4.4 and multiplying the rounded result
by 1,000.
The convergence of the temperature and dew point lapse rate is 4.4oF per
1,000ft
 What is the approximate base of the cumulus clouds if the surface air Cumulus stage: characterized by continuous updrafts, and these
temperature is 70oF and the dew point is 61oF updrafts create low-pressure areas
Mature stage: thunderstorm reach their greatest intensity during this
stage, which is characterized by updrafts and downdrafts inside the cloud
precipitation inside the cloud aids in the development of these
downdrafts and the start of rain from the base of the cloud signals
the beginning of the mature stage.
The precipitation that evaporates before it reaches the ground is
called virga
Dissipating stage: of a thunderstorm is characterized predominantly be
downdrafts

Lighting is always associated with a thunderstorm

Hail is formed inside thunderstorms by the constant freezing, melting, and
refreezing of water as it is carried about by the up and downdrafts
Turbulence
A pilot should always expect the hazardous and invisible atmospheric phenomena
Cumulus clouds are formed by convective currents (heating from below), therefore a
called wind shear turbulence when operating anywhere near a thunderstorm (within 20
pilot can expect turbulence below or inside cumulus clouds, especially towering
NM)
cumulus clouds.
The greatest turbulence could be expected inside cumulonimbus clouds Thunderstorms that generally produce the most intense hazard to aircraft are called
squall-line thunderstorms. These non-frontal, narrow bands of thunderstorms often
If severe turbulence is encountered either inside or outside of clouds, the
develop ahead of a cold front
airplanes airspeed should be reduced to maneuvering speed and the pilot should
attempt to maintain level flight attitudes because the amount of excess load that Embedded thunderstorms are those that are obscured by massive cloud layers and
can be imposed on the wing will be decreased. Any attempt to maintain a constant cannot be seen
attitude will greatly increase the stresses that are applied to the aircraft
Wind Shear
Thunderstorms
Wind shear is defined as a change in wind direction and/or speed over a very short
Thunderstorms present many hazards to flying. 3 conditions necessary to the distance in the atmosphere. This can occur at any level of the atmosphere and can
formation of a thunderstorm are: be detected by the pilot as a sudden change in airspeed.

1. Sufficient water vapor

Low-level wind shear can be expected during strong temperature inversions,
2. An unstable lapse rate
on all sides of a thunderstorm and directly below the cell.
3. An initial upward boost (lifting)
A pilot can expect a wind shear zone in a temperature inversion whenever the
wind speed at 2,000ft to 4,000ft above the surface is 25knots
The initial upward boost can be caused by heating from below, frontal lifting, or
by mechanical lifting (wind blowing air upslope on a mountain) low level wind shear can also be found near frontal activity because
winds can be significantly different in the two air masses which meet to
There are 3 stages of a thunderstorm:
form the front
the cumulus
mature In warm front conditions, the most critical period is before the front passes.
dissipating stages
Warm front shear may exist below 5,000ft for about 6 hours before surface
passage of the front
The wind shear associated with a warm front is usually more extreme than that
found in cold fronts

The shear associated with cold fronts is usually found behind the front, if the
front is moving at 30 knots or more the shear zone will be 5,000 feet above the
surface 3 hours after frontal passage

Two potentially hazardous situations:

the loss of a tailwind

the loss of a headwind

Tailwind may shear to either a calm or a headwind component

The airspeed initially increases, the aircraft pitches up, and

altitude increases
Lower than normal power would be required initially, followed by a
further decrease as the shear is encountered, and then an increase as the
glide slope is regained

A headwind may shear to a calm or tailwind component.

Initially the airspeed decreases, the aircraft pitches down, and

altitude decreases

Some airports can report boundary winds as well as the wind at the tower. When a
tower reports a boundary wind which is significant different from the airport wind,
there is possibility of hazardous wind shear
Icing
Structural icing occurs on an aircraft whenever supercooled condensed droplets of
water make contact with any part of the aircraft that is also at a temperature
below freezing.

An inflight condition necessary for structural icing to form is visible

moisture (clouds or raindrops)
 An abundance of condensation nuclei from combustion products makes fog prevalent in
Icing in precipitation, (rain) is of concern to the VFR pilot because it can industrial areas
occur outside of the clouds.
Fog is classified the way it is formed:
Aircraft structural ice will most likely have the highest accumulation
in freezing rain which indicates warmer temperature at a higher altitude Radiation fog (ground fog): is formed when terrestrial radiation cools the
ground, which in turn cools the air in contact with it.
When the air is cooled to its dew point (or within a few degrees), fog
The presence of ice pellets at the surface is evidence that there is freezing rain
will form
at a higher altitude, while wet snow indicates that the temperature at your
This fog will form most readily in warm, moist air over low, flatland,
altitude is above freezing.
areas on clear, calm (no wind) nights
a situation conductive to any icing would be flying in the vicinity of a Advection fog (sea fog): is formed when warm, moist air moves (wind is
front required) over colder ground or water (an air mass moving inland from the coast
in winter)
Upslope fog): is formed when moist stable air is cooled to its dew point as
it moves (wind is required) up sloping terrain.
cooling will be at the dry adiabatic lapse rate of approximately 3oC per
1,000ft
Precipitation (rain or drizzle)-induced fog is most commonly associated with
frontal activity and is formed by relatively warm drizzle or rain falling
through cooler air.
evaporation from the precipitation saturates the cool air and fog forms.
This fog is especially critical because it occurs in the proximity of
precipitation and other possible hazards such as icing, turbulence, and
thunderstorms
Steam fog: forms in the winter when cold, dry air passes from land areas over
comparatively warm ocean waters.
low level turbulence can occur and icing can become hazardous in a steam
fog

Frost
Frost is described as ice deposits formed by sublimation on a surface when the
temperature of the collecting surface is at or below the dew point of the adjacent
air and the dew point is below freezing

Frost causes early airflow separation on an airfoil resulting in a loss of lift.

Therefore all frost should be removed from the lifting surface of an airplane
before flight or it may prevent the plane from becoming airborne

Fog Weather Services

Fog is a surface-based cloud (restricting visibility) composed of either water An international weather reporting code is used for weather reports (METAR) and
droplets or ice crystals. forecasts (TAFs) worldwide.
Fog may form by cooling the air to its dew point or by adding moisture to the air
For aviation purposes the ceiling is the lowest broken or overcast layer, or
near the ground.
vertical visibility into an obscuration.
A small temperature/dew point spread is essential to the formation of fog.

Station Identifier

Each reporting station is listed by its 4 letter International Civil Aviation

Organization (ICAO) identifier.

Time of Report

The date (day of the month) and time of the observation.

The time is given in UTC or Zulu as indicated by a Z.

"122150Z" -> 12th of the month at 2150Z

Modifier

When a METAR is created by a totally automated weather observation station, the

modifier AUTO follows the date/time element

The modifier COR is used to indicate a corrected METAR and replaces a previously
disseminated report.

Wind Information

The wind direction and speed are reported in a five digit group, or six digits if
the speed is over 99 knots.

The first 3 digits represent the direction from which the wind is blowing in
reference to true North.
The next 2 or 3 digits show the speed in knots (KT)
Calm winds are reported as 00000KT
Aviation Routine Weather Report (METAR) Gusty winds are reported with a G, followed by the highest gust
If the wind direction varies 60 degrees or more and speed is above 6 knots, a
variable group follows the wind group.
the extremes of wind direction are shown separated by a V
If the wind is blowing from 020o, varying 090o it is reported as 020V090

Type of Report

METAR: taken every hour

non-routine (special) aviation weather report SPECI): weather observation
that is an unscheduled report indicating a significant change in one or more
elements
Visibility 1. intensity or proximity
2. descriptor
Prevailing visibility is the greatest distance an observer can see and 3. precipitation
identify objects through at least half of the horizon. 4. obstruction to visibility
5. any other weather phenomena
When the prevailing visibility varies from one area of the sky to
another, the visibility in the majority of the sky is reported The intensity or proximity and/or descriptor are used to qualify the precipitation,
If visibility varies significantly, the observer can report individual obstruction, or other weather phenomena
sector visibilities in the remarks section of the METAR
Qualifier and Descriptor
Visibility is reported in statute miles (SM):
1/2SM indicates one-half statute mile +TSRA

Intensity or proximity is shown immediately prior to the precipitation codes.

The indicated intensity applies only to the first type of precipitation reported.
Intensity levels are:

light -
moderate no sign
heavy +

Weather obscurations occurring in the vicinity (between 5 and 10 statute miles) of

the airport are shown by the letters VC.
For precipitation, VC applies within 10 statute miles of the observation point.
VC will not appear if an intensity qualifier is reported

Weather Phenomena

Up to 3 types of precipitation can be coded in a single grouping of present weather

Runway Visual Range (RVR) might be reported following prevailing visibility.
condition,
When more than one is reported, they are shown in order of predominance.
Weather
Obscurations, which limit visibility are after any reported precipitation.
Weather or obstructions to vision that are present at the time of the observation
Fog (FG) is listed when the visibility is less than 5/8 stature mile. If the
are reported immediately after the visibility in the following order:
visibility were to increase to between 5/8 and 6 statute miles the code for must

mist (BR) would be used. Amount of Clouds

Shallow fog, patches of fog, or partial fog might be coded with prevailing
visibility of 7 statute miles or greater. The amount of clouds covering the sky is reported in eighths or octas of sky cover:

Clear sky: SKC (manual), CLR automated

Automated stations cannot detect clouds above 12,000ft, a report of clear
indicates there were no clouds detected below 12,000ft
FEW: 0 - 2/8
SCT: 3/8 - 4/8 : scattered
BKN: 5/8 - 7/8 : broken
OVC: overcast

Height, Type, and Vertical Visibility

The height of clouds or the vertical visibility into obscuring phenomena is

reported with 3 digits in hundreds of feet above ground level (AGL).

To determine the cloud height, add 2 zeros to the number given in the
report.

When more than one layer is present, the layers are reported in ascending order.
Automated stations can only report a maximum of 3 layers at 12,000ft AGL
Human observers can report up to 6 layers of clouds at any altitude

In the example the scattered layer was at 800ft AGL and the overcast layer was at
1,200ft AGL, the base of the cumulonimbus clouds is at 1,200ft AGL

In a manual report a cloud type might be included if towering cumulus clouds (TCU)
or cumulonimbus clouds (CB) are present. The code follows the height of their
reported base.
A ceiling is the AGL height of the lowest layer of clouds that is reported as
broken or overcast, or the vertical visibility into an obscuration such as fog or
haze.

Temperature and Dewpoint

The observed air temperature and dewpoint (Celsius) are listed immediately
following the sky condition.

In the example it is 20 degrees Celsius and the dew point is 18

If it were below zero the temp is M10, for -10 Celsius

Altimeter

The altimeter setting is reported in inches of mercury in a four-digit group

prefaced by an A

In the example the altimeter setting was reported as 29.95

Terminal Aerodrome Forecast
Remarks Terminal Aerodrome Forecast (TAF) are normally valid for a 24-hour period and are
scheduled 4 times a day 0000Z, 0600Z, 1200Z, 1800Z
Remarks are RMK
Each TAF contains:

type
location
issuance date and time
valid date and time
forecast

Pilot Weather Reports

PIREPs often confirm such information as the height of bases and tops of cloud
layers, in-flight visibility, icing conditions, wind shear, and turbulence

Type of Forecast

TAF : normal routine forecast

TAF AMD : amended

COR : corrected
AIRMETs (WA): contain information on weather that may be hazardous to single
RTD delayed engine, other light aircraft, and VFR pilots

Winds and Temperatures Aloft Forecast The items covered are moderate icing or turbulence, sustained winds of
30 knots or more at the surface, widespread areas of IFR conditions, and
A winds and temperatures aloft forecast (FD) provides an estimate of extensive mountain obscurement

wind direction in relation to true north

wind speed in knots SIGMETs (WS): advise of weather potentially hazardous to all aircraft.
and temp in C
The items covered are severe icing, severe or extreme turbulence, and
widespread sandstorms, dust storms or volcanic ash lowering visibility to
2635-08 indicates the wind is from 260o at 35 knots and the temperature is 8C
less than 3 miles

SIGMETs and AIRMETs are broadcast upon receipt and 30-minute intervals (H + 15 and
H + 45) during the first hour.
If the advisory is still in effect after the first hour, an alert notice will be
broadcast.

Pilots may contact the nearest FSS to ascertain whether the advisory is pertinent
to their flights

Convective SIGMETs (WST): cover weather developments such as tornadoes,

lines of thunderstorms, and embedded thunderstorms and they also imply
severe or greater turbulence, sever icing, and low-level wind shear.

When a SIGMET forecasts embedded thunderstorms, it indicates that the

thunderstorms are obscured by massive cloud layers and cannot be seen.
Convective SIGMET bulletins are issued hourly at H + 55
Unscheduled convective SIGMETs are broadcast upon receipt and at 15
minute intervals for the first hour (H+15, H+30, H+45)
Wind speeds between 100 and 199 knots are encoded so direction and speed can
be represented by 4 digits. Obtaining a Telephone Weather Briefing
This is done by adding 50 to the two-digit wind direction and subtracting
When telephoning a weather briefing facility for preflight weather information,
100 from the velocity
pilots should:
A wind of 270o at 101 knots is encoded as 7701 (27+50=77 for wind direction,
and 101-100=01 for wind speed) identify themselves as pilots
state whether they intend to fly VFR or IFR
A code of 9900 indicates light and variable winds (less than 5 knots)
request a standard briefing to get a "complete" weather briefing
request an abbreviated briefing to supplement mass disseminated data or when
Inflight Weather Advisories only one or two items are needed
request an outlook briefing whenever the proposed departure time is 6 or more
Inflight Weather Advisories advise enroute pilots of the possibility of
hours from the time of briefing
encountering hazardous flying conditions that may not have been forecast at the
time of the preflight weather briefing