Using the ACS

PA.I.C.KC
(Applicable ACS.
Area of Operation.
Task.
Task Element Knowledge)

ASEL: Airplane – Single-Engine Land

ASES: Airplane – Single-Engine Sea
AMEL: Airplane – Multiengine Land
AMES: Airplane – Multiengine Sea

Checkride Minimum Elements

From each applicable Task:

At least one knowledge element

At least one risk management element
All skill elements The arm is the horizontal distance measured in inches from the datum
any Task elements in which the applicant was shown to be deficient on the line to a point on the aircraft
knowledge test If measured aft, toward the tail, the arm is given a positive (+)
value.
Knowledge Test If measured forward, toward the nose, the arm is given a negative
(-) value
#Regulations
The moment is the product of the weight of an object multiplied by its
#Accident_Reporting
arm and is expressed in pound-inches (lbs-in)
#Performance_Charts
Formula: Weight x Arm = moment
#Radio_Communications
The moment index is a moment divided by a constant such as 100 or
#Weather
1,000
#Safe_and_Efficient_Operation
It is used to simplify computations where heavy items and long arms
#Density_Altitude result in large, unmanageable numbers. This is usually expressed as
#Weight_and_Balance Moment/100 or Mom/1,000
#Aerodynamics_Powerplants_and_Aircraft_Systems
#Stalls_and_Spins The center of gravity (CG) is the point about which an aircraft will balance and it
#Aeronautical_Decision-Making_ADM is expressed in inches from the datum.
#Preflight_action The center of gravity is found by dividing the total moment by the total weight and
the for is:
Sections (total moment)/(total weight) = CG(inches aft of datum)

I. Preflight Preparation Standard Weights

II. Preflight Procedures
III. Airport and Seaplane Base Operations have been established for numerous items involved in weights and balance
IV. Takeoff, Landings, and Go-Arounds computations.
V. Performance and Ground Reference Maneuvers These weights should not be used if actual weights are available. Some standard
VI. Navigation weights are:

VII. Slow Flight and Stalls Item Weight

VIII. Basic Instrument Maneuvers General aviation crew and passenger 190lbs each
IX. Emergency Operation
Gasoline 6lbs/gallon
X. Multiengine Operations
XI. Night Operations Oil 7.5lbs/gallon
XII. Postflight Procedures Water 8.35lbs/gallon

Aircraft Performance Airplane

Weight and Balance In addition to considering the weight to be carried, the pilot must ensure that the
load is arranged to keep the aircraft balance.
Even though an aircraft has been certified for flight at a specified maximum gross
weight, it may no be safe to take off with that load under all condition. High The balance point, or CG, is the point at which all of the weight of the
altitude, high temperature, and high humidity are additional factors which may airplane is considered to be concentrated.
require limiting the load to some weight less than the maximum allowable. For an aircraft to be safe to fly, the center of gravity must fall between
specified limits
Some of the problems caused by overloading an aircraft are:
Each category has specific balance requirements
the aircraft will need a higher takeoff speed, which results in a longer
To keep the CG within safe limits it may be necessary to move weight
takeoff run
toward the nose of the aircraft (which moves the CG forward) or move the
both the rate and angle of climb will be reduced
weight toward the tail (moving the CG aft)
the service ceiling will be lowered
the cruising speed will be reduced
cruising range will be shortened
Computing Weight and Balance Problems Using a Table
maneuvering will be decreased
a longer landing roll will be required because the landing speed will be
higher
excessive loads will be imposed on the structure, especially the landing gear

Empty weight: obtained from the appropriate charts.

it includes the airframe, engine, all fixed equipment, and unusable

fuel and oil.
some aircraft include all oil in the aircraft empty weight

Useful Load: includes the pilot, passengers, baggage, fuel and oil

Takeoff weight: is the empty weight plus the useful load

Landing weight: the takeoff weight minus any fuel used

 Density Altitude and Aircraft Performance
Aircraft performance charts show a pilot what can be expected of an airplane (rate
of climb, takeoff roll, etc) under stipulated conditions

Prediction of performance is based upon sea level temperature of 15C (+59F) and
atmospheric pressure of 22.92Hg
This combination of temperature and pressure is called standard day
When the air is at standard density, temperature and/or pressure deviations will
change the air density, or the density altitude, which affects aircraft
performance.

Performance charts allow the pilot to predict how an aircraft will perform

Relative humidity also affects density altitude, but is not considered when the
performance charts are formulated:

a combination of high temperature, high humidity, and high altitude result in

a density altitude higher than the pressure altitude which in turn results in
reduced aircraft performance

Computing Weight and Balance Problems Using a Graph

Takeoff Distance
The Takeoff Distance Graph FAA Figure 40, allows the pilot to determine the ground
roll required for take off under various conditions.
It shows the total distance required for a takeoff and climb to clear a 50-foot
obstacle

Cruise Power Setting Table

The Cruise Power Setting Table FAA Figure 35 may be used to forecast fuel flow and
true airspeed and therefore allow a pilot to determine the amount of fuel required
and the estimated time en-route
 Ignition and Electrical Systems
Landing Distance Graphs and Tables
Most reciprocating engines used to power small aircraft incorporate two separate
Some Landing Distance Graphs such as FAA Figure 37, 38 are used in the same manner magneto ignition systems
as the takeoff distance graph.
magneto is a self-contained source of electrical energy, to even if an
aircraft loses total electrical power, the engine will continue to run

When checking for magneto operation prior to flight, the engine should
run smoothly when operating with the magneto selector set on "BOTH" and
should experience a slight drop revolutions per minute (RPM) when running
on only one magneto

The main advantages of the dual ignition system are increased safety and improved
engine performance

Headwind and Crosswind Component Graph

In general taking off into a wind improves aircraft performance, and reduces the
length of the runway required to become airborne.
The stronger the wind, the better the aircraft performs.

Crosswinds, however, may make the aircraft difficult or impossible to control.

The aircraft manufacture determines the safe limit for taking off or landing
with a crosswind and establishes the maximum allowable crosswind component.

The graph shown in FAA Figure 36 is used to determine what extent a wind of a given Fuel Induction Systems
direction and speed is felt as a headwind and/or crosswind
Carburetor Induction System: The float-type carburetor takes in air that
flows through a restriction (venturi) which creates a low-pressure area.
The pressure difference between the low-pressure area and outside air forces
fuel into the airstream where it is mixed with the flowing air, drawn
through an intake manifold, and delivered to he combustion chambers and
ignited

Carburetors are normally set to deliver the correct air/fuel mixture

at sea level.
since air density decreases with altitude, a mixture control allows
the pilot to decrease the fuel flow as altitude increases and this
maintain the correct mixture: otherwise the mixture becomes too rich
at high altitudes
When descending air density increases: unless fuel flow is increased,
the mixture may become lean
Maximum Range Performance
Maximum endurance is obtained at the point of minimum power to maintain the Fuel Injection System: the fuel and air are mixed just prior to entering the
aircraft in steady, level flight combustion chamber (no carburetor is used)

When range and economy of operation are the principal goals, the pilot must ensure
that the airplane will be operated at the recommended long-range cruise performance
Carburetor Ice
As air flows through a carburetor it expands rapidly.
Aircraft Systems At the same time fuel forced into the airstream is vaporized.
Expansion of the air and vaporization of the fuel causes a sudden cooling of the
Reciprocating Engines mixture which may cause ice to form inside the carburetor.
The possibility of icing should always be considered when operating in conditions
Pistons move back and forth within the cylinders where the temperature is between 20F and 70f and the relative humidity is high
Connecting rods connect the pistons to the crankshaft, which converts
the and forth movements of the pistons to a rotary motion Carburetor heat preheats the air before it enters the carburetor and either
This rotary motion drives the propeller' prevents ice from forming or may melt the ice

One cycle of the engine consists of two revolutions of the crankshaft. When carburetor heat is applied the heated air that enters carburetor is less
These two crankshaft revolutions require four strokes of the piston: dense.
this causes the fuel/air mixture to become enriched and this in turn
intake
decreases engine output and increases engine operating temperatures
compression
power
During engine runup prior to departure from a high-altitude airport, the
exhaust
pilot may notice a slight engine roughness which is not affected by the
magneto check, but grows worse during the carburetor heat check: in this
case the air/fuel mixture may be too rich due to the lower air density at
the high altitude and applying carburetor heat decreases the air density
even more. A leaner setting of the mixture control may correct this problem

In a fixed-pitch propeller airplane, the first indication of carburetor ice would

likely be a decrease in RPM as the air supply is choked off. Application of
carburetor heat will decrease air density, cause the RPM to drop even lower. Then
Reactive force: is based on Newton's Law of action and reaction
as the ice melts, the RPM will rise gradually
A propeller rotating in a clockwise direction (as seen from the rear)
Fuel injection systems do not utilize a carburetor and are generally considered to produces a force which tend to roll the airplane in a counter-clockwise
be less susceptible to icing than carburetor systems are direction

Aviation Fuel
Fuel does 2 things for the engine:

it acts as an agent for combustion

an agent for cooling (based on mixture setting)

Aviation fuel is available in several grades. The proper grade will be listed, a
higher grade fuel can be used, but a lower grade fuel should not be used:

the use of a lower grade fuel in a lean mixture may cause detonation
which is the uncontrolled spontaneous explosion of the mixture in the
cylinder (this causes extreme heat)

Preignition: the premature burning of the air/fuel mixture.

It is caused by an incandescent area (such as carbon or lead deposit heated
to a red glow) which serves as an ignition advance of normal ignition

Two fuel pump systems are used on most airplanes:

the main pump system is engine driven and an auxiliary electric driven pump
is provided for use in the vent the engine pump fails
the auxiliary pump (boost pump) provides added reliability and aids in engine
start up

Engine Temperatures
Engine lubrication oil not only prevents direct metal-to-metal of moving parts, it
also absorbs and dissipates some of the engine heat produced by internal combustion

If the engine oil level should fall too low, an abnormally high engine oil
temperature indication may result

On the ground or in the air, excessively high engine temperature can cause
excessive oil consumption, loss of power, and possible internal engine damage

If the engine oil temperature and cylinder head temperature gauges have Spiraling slipstream: the reaction of the air to rotating propeller
exceeded their normal operating range, or if the pilot suspects that the
the propeller forces the air to spiral in a clockwise direction around
engine is detonating during climb out:
the fuselage
the pilot may be operating with either too much power and the mixture this spiraling slipstream strikes the airplanes vertical stabilizer on
set to lean the left side
using fuel of too low a grade this pushes the tail of the airplane to the right and nose of the
or operating the engine with insufficient amount of oil in it airplane to the left
reducing the climb rate and increasing airspeed enriching the fuel
mixture, retarding the throttle will aid in cooling an engine that is
overheating

The most important rule to remember in the even of a power failure after becoming
airborne is to maintain safe airspeed

Propellers
The throttle controls the power output as registered on the manifold pressure
gauge, and the propeller controller regulates the engine RPM.

A pilot should avoid a high manifold pressure setting with low RPM on
engines equipped with a constant-speed propeller. To avoid high manifold
pressure combined with low RPM:

reduce the manifold pressure before reducing RPM when decreasing power
setting
or increase the RPM before increasing the manifold pressure when
increasing power settings

Torque
An airplane of standard configuration has a tendency to turn left.
This tendency is called torque and is a combination of 4 forces:

reactive force
spiraling slipstream
gyroscopic precession
P-factor
 Gyroscopic precession: the result of a deflective force applied to a Class C airspace
rotating body
All class C airspace has the same dimensions with minor site variations.
the resultant action occurs at 90 degree later in the direction of They are composed of 2 circles both centered on the primary airport
rotation
The inner circle (surface area) has a radius of 5 nautical miles and
extends from the surface up to 4,000ft above the airport
The outer circle (shelf area) has a radius of 10 nautical miles and
extends vertically from 1,200ft AGL up to 4,000ft above the primary
airport
In addition to the Class C airspace proper, there is an outer area
with a radius of 20 nautical mils and vertical coverage from the lower
limits of the radio/radar coverage up to the top of the approach control
facility's delegated airspace
Within the outer are, pilots are encouraged to participate but it
is not a VFR requirement
Class C airspace service to aircraft proceeding to a satellite airport
will be terminated at a sufficient distance to allow time to change to
the appropriate tower or advisory frequency.
Aircraft departing satellite airports within Class C airspace shall
establish two-way communication with ATC as soon a practicable after take
off
On charts Class C airspace is depicted by solid magenta lines

Class D airspace
Class D airspace extends upward from the surface to approximately 2,500ft
AGL.
Asymmetric propeller loading (P-factor): caused by the downwind moving blade
Class D airspace may include one or more airports and is normally 4 nautical
on the right side of the propeller having a higher angle attack, a greater
miles in radius.
action and reaction, and therefore a higher thrust than the upward moving
opposite blade. This results in a tendency for the aircraft to yaw to the When the ceiling of class D airspace is less than 1,00ft and/or the
left around the vertical axis visibility is less than 3 statute miles, pilots wishing to take off or
land must hold and instrument rating, must have instrument flight plan,
additional left-turning tendency from torque will be greatest when the
and must have received clearance from ATC.
aircraft is operating at low airspeed with a high power setting
The aircraft must be equipped to takeoff or land when the weather
is less than that required for visual flight rules
Preflight Inspection Procedures When special VFR flight is prohibited it will be depicted by "No SVFR"
above the airport information on the chart
A thorough preflight inspection should be performed on an aircraft to help ensure
that the aircraft is prepared for safe flight and should be thorough and
systematic.

Prior to every flight, a pilot should at least perform a walk-around inspection of

the aircraft

After an aircraft has been stored for an extended period of time, a special check
should be made during preflight for damage or obstructions caused by animals, birds
or insects

The use of a written checklist for preflight inspection and starting the engine is
Class E airspace
recommended to ensure that all necessary items are checked in a logical sequence
Will be blue if next to Class G airspace
Airspace Magenta shading identifies class E airspace starting at 700ft AGL and no
shading identifies starting at 1,200ft(varies) AGL
Controlled airspace, airspace within which some or all aircraft may be subject to
All airspace from 14,500 to 17,999 feet is Class E airspace
air traffic control, consists of those areas designated Class A, B, C, D, E
It also includes the surface of some airports with an instrument approach
airspace
but no control tower
Much of the controlled airspace begins at either 700ft or 1,200ft above the
ground. An Airway is a corridor of controlled airspace extending from 1,200ft above the
The lateral limits and floors of Class E airspace of 700 ft are defined by a surface or as designated, up to and including 17,999ft MSL, and 4 nautical miles
magenta vignette; while the lateral limits and floors of 1,200ft are defined by either side of the center line
a blue vignette if it abuts uncontrolled airspace
Floors other than 700ft or 1,200ft are indicated by a number indicating the Class G
floor
Class G airspace is airspace within which Air Traffic Control has neither
the authority nor responsibility to exercise any control over air traffic.
Class A airspace
Typically extends from the surface to the base of the overlying
Class A airspace extends from 18,000ft MSL up to and including FL6000 and is
controlled Class E airspace
not depicted on VFR sectional charts.
In some cases like Alaska, and the western U.S class G airspace may
No flight under VFR, including VFR-On-Top is authorized in Class A extend to 14,500ft MSL
airspace
Prohibited areas are blocks of airspace within which the flight of an aircraft is
prohibited
Class B airspace
Restricted areas denote the presence of unusual, often invisible hazards to
Class B airspace consists of controlled airspace extending upward from the
aircraft such as artillery firing, aerial gunnery, or guided missiles. Penetration
surface or higher to specified altitudes of Restricted areas without authorization of the using or controlling agency may be
Each class B airspace sector, outlined in blue on the sectional chart extremely hazardous
is labeled with its delimiting altitudes
Warning area contain the same hazardous activities as restricted areas, but are
Each Class B airspace location will contain at least one primary
located in international airspace
airport
An ATC clearance is required prior to operating within Class B Military Operations Areas (MOAs) consist of airspace established for the purpose of
airspace separating certain military training activities from IFR traffic.
A pilot landing or taking off from one of a group of 12 specific, busy
airports must hold at least a private pilot certificate. Pilots operating under VFR should exercise extreme caution while flying
At other airports a student pilot may not operate an aircraft on a within an active MOA.
solo flight within Class B airspace, or to from or at an airport Any Flight Service Station within 100 miles of the area will provide
located within Class B airspace unless both ground and flight information concerning MOA hours of operation
instruction has been received from an authorized instructor Prior to entering an active MOA pilots should contact the controlling agency
The students logbook must be authorized within the preceding 90 for traffic advisories
days
Alert Areas may contain a high volume of pilot training activities or an unusual
Each airplane operating within Class B airspace must be equipped with
type of aerial activity, neither of which is hazardous to aircraft.
a two-way radio with appropriate ATC frequencies, and a 4096 code
transponder with Mode C/S automatic altitude-reporting capability
Pilots of participating aircraft as well as pilots transiting the area are
equally responsible for collision avoidance
Aircraft are requested to remain at least 2,000ft above the surface of National
relative wind: wind felt by an airfoil.
Parks, National Monuments, Wilderness and Primitive Areas, and National Wildlife
Refuges It is created by the movement of air past an airfoil, by the motion of
an airfoil through the air, or a combination of the two
Military Training Routes (MTRs) have been developed for use by the military for the Relative wind is parallel and in the opposite direction of the flight
purpose of conducting low-altitude, high-speed training. path of the airfoil

Generally MTRs are established below 10,000ft MSL for operations at speeds in
excess of 250 knots

IFR Military Training Routes (IR) operations are conducted in accordance with
instrument flight rules, regardless of weather conditions.
VFR Military Training Routes (VR) operations are conducted in accordance with VFR.
IR and VR at and below 1,5000ft AGL will identified by four digit numbers (VR1351,
IR1007)
IR and VR above and below 1,500 AGL will be identified by three digit numbers,
IR341, VR426

Basic Aerodynamic
Aerodynamic Terms

airfoil: structure or body which produces a useful reaction to air movement

airplane wings, helicopter blades and propellers are airfoils

chord line: imaginary line from the leading edge to the trailing edge of an angle of attack: angle between the chord line of the airfoil and the
airfoil relative wind

changing the shape of an airfoil (by lowering flaps) will change the
chord line

angle of incidence: angle at which a wing is attached to the aircraft

fuselage

Axes of Rotation and the Four Forces Acting in Flight

Aircraft have three axes of rotation: lateral, longitudinal, and vertical
 longitudinal axis: imaginary line from nose to tail

rotation around this axis is called roll

roll is controlled by the ailerons and this rotation is called lateral
control/stability

lateral axis: imaginary line from wing tip to wing tip vertical axis: imaginary line extending through the intersection of the
lateral and longitudinal axes
rotation around this axis is called pitch
pitch is controlled by elevators and this rotation is called rotation around this axis is called yaws
longitudinal control/stability yaw is controlled by the rudder and this rotation is called
directional control/stability

center of gravity: the point at which an airplane would balance if it were

suspended on that point

The 3 axes intersect at the center of gravity

Weight shift control and powered parachutes rotate around this center
of gravity
Four Forces Parasite drag: the resistance of the air produced by any part of an airplane
that does not produce lift (landing gear, antennae)

parasite drag will increase as airspeed increases

Induced drag: a by-product of lift. Drag that is induced as the wing

develops lift

induced drag increases as airspeed increases

Lift

As the velocity of a fluid (gas or liquid) increases, its pressure decreases:

Bernoulli's Principle

Lift is the result of a pressure difference between the top and the bottom
of the wing

A wing accelerated the air over the top of the wing decreasing the
pressure above the wing

4 factors are involved in creating lift:

angle of attack
wing area and shape (planform)
air velocity
air density

The pilot can control angle of attack and airspeed, increasing either increases
lift. During unaccelerated (straight and level) flight the 4 forces are in equilibrium:

lift = weight
thrust = drag

Stability
Stability is the inherent ability of an airplane to return or not return to its
original flight condition after being disturbed by an outside force, such as rough
air.

Weight

Weight is the force with which gravity attracts all bodies vertically toward the
center of the earth

Thrust

Thrust is the forward force which is produced by the propeller acting as an airfoil
to displace a large mass of air to the rear

Drag

Drag is a rear-ward acting force which resists the forward movement of an airplane
through the air. 2 types of drag: parasite, induced
 positive static stability: initial tendency of an aircraft to return or not Effects of Aft CG
return to its original position
1. Decreased longitudinal stability
2. Higher cruise speed
3. Lower cruise speed
4. Lower stall speed
5. Poor stall/spin recovery

Turns, Loads, and Load Factors

Horizontal Lift Component: When an airplane is banked into a turn, a portion

of the vertical lift being developed is diverted into horizontal lift
component.
The reduced Vertical Lift Component results in a loss of altitude unless
total lift is increased by:

increasing angle of attack

increasing air speed
increasing both

Load is the force (imposed stress) that must be supported by an airplane structure
in flight.

The loads imposed on the wings in flight are stated in terms of load factor
in straight and level flight the airplane has a load factor of 1 (1 G)

positive dynamic stability: tendency of an oscillating airplane (with Centrifugal force: a force that acts toward the outside of the curve any
positive static stability) to return to its original position relative to time an airplane is flying a curved path (turns, climbs, descents)
time
when the airplane is flying a curved flight the load the wings must
support will be equal to the weight of the airplane plus the load imposed
by centrifugal force
as the angle of bank of a turn increases the load factor increases

The location of the CG with respect to the center of lift will determine the
The amount of excess load that can be imposed on the wing of an airplane depends on
longitudinal stability of an airplane:
the speed of the airplane: a change in direction made at high speed with forceful
an airplane will be less stable at all airspeeds if it is loaded to the most control movement results in a high load factor
aft CG
a more inherently stable airplane is easier to control An increased load factor (weight) will cause the airplane to stall at a higher
speed
Changed in pitch can also be experienced with changes in power settings, except in
T-tail airplanes Some conditions that increase the load (weight) of an aircraft are:

overloading the airplane

when power is reduced their is reduced downwash on the tail resulting in the
nose pitching down too steep an angle of bank
turbulence and abrupt movement of the controls
A properly designed weight-shift control is stable because the center of lift is
above the CG

slower than trim the center of lift moves aft

faster than trim the center of lift moves forward to make the aircraft stable

Effects of Forward CG

1. Increased longitudinal stability

2. Lower cruise speed
3. the wing flies at a higher angle of attack to create more lift to counter the
added downward forced produced by the tail, therefore the wing also produced
more induced drag
4. Higher stall speed
5. the flies at a higher angle of attack to create more lift to counter the added
downward forces produced by the tail, therefore the wing also produces more
induced drag
 Turns Around a Point

Turns around a point: the wings will be in alignment with the pylon only during the
time the airplane is flying directly upwind or directly downwind.
At all other points a wind correction angle will keep the wings from pointing
directly at the pylon.

If the student is instructed to not exceed a 45o bank in a turn around a

point maneuver, the best place to start is the point where the bank angle will
be steepest, which is when flying downwind.
throughout the remainder of the maneuver, the bank angle will be
Aircraft are separated into categories determined by the loads that their wing shallowing out
structures can support. The ground speed will be equal where the airplane is flying with the same
headwind component.
the angle of bank will be the same only where the airplane is flying
directly crosswind

Maneuvers S-Turns

Rectangular Course In visual flight a steep turn is anything grater than 45o

Rectangular course: the flight path should be positioned outside the field In a steep turn the ground speed will be the same when the airplane has the
boundaries just far enough that they may be easily observed from either pilot seat same headwind component
by looking out the side of the airplane. The steepest angle of bank is required at the points where the airplane is
flying downwind
The closer the track of the airplane is to the field boundaries, the steeper The airplane will have to be crabbed into the wind the greatest amount where
the bank necessary at the turning points it is flying crosswind
 In the first half of the S-turn the bank should begin shallow and
increase in steepness as the airplane turns cross wind and becomes
steepest where the turn is downwind
if the turn is started with too steep a bank angle the bank will
increase too rapidly and the upwind half of the "S" will be smaller than
the downwind half
the turn will not be completed by the time the airplane is over the
reference line

Ground Effect

Ground Effect occurs when the airplane is flying within one wingspan or less
above the surface

The airflow around the wing and wing tips is modifies and the resulting
pattern reduces the downwash and the induced drag
These changes can result in an aircraft becoming airborne before reaching
recommended takeoff speed or floating during and approach
An airplane leaving ground effect after takeoff will require an increase in
angle of attack to maintain the same lift coefficient
which in turn will cause an increase in induced drag and therefore
require increased thrust
Stalls and Spins
At an angle of attack of about 18o-20o (for most wings), turbulence over the upper
wing surface decreases so drastically that flight can not be sustained and the wing
*stalls

The angle at which a stall occurs is called the critical angle of attack

an airplane can stall at any airspeed or any altitude, but will always
stall at the same critical angle of attack
the indicated airspeed at which a given airplane will stall in a
particular configuration, will remain the same regardless of altitude
Because air density decreases with an increase inn altitude the airplane
has to be flown at a faster speed at higher altitudes to cause the same
pressure difference between pitot impact pressure and static impact

Wake Turbulence
All aircraft leave two types of wake turbulence:

prop/jet blast
wing-tip vortices

The prop/jet blast could be hazardous to light aircraft on the ground behind
large aircraft which are either taxiing or running-up their engines.

In the air prop/jet blast dissipates rapidly

Wing-tip vortices are a by product of lift

When a wing is flown at a positive angle of attack a pressure

differential is created between the upper and lower wing surface, and the
pressure above the will be lower than the pressure below the wing.
in attempting to equalize the pressure, air moves outward, upward
and around the wingtip: setting up a (vortex) behind each wing

The strength of a vortex is governed by the weight, speed, and the shape of
the wing
An aircraft will spin only after it has stalled, and will continue to spin as long maximum vortex strength occurs when the generating aircraft is heavy,
clean, and slow
as the outside wing continues to provide more lift than the inside wing and the
aircraft remains stalled Vortices generated by large aircraft in flight tend to sink below the flight
path of the generating aircraft
Flaps a pilot should fly at or above the larger aircrafts flight path in order
to avoid wake turbulence created by the wing tip vortices
Extending the flaps increases the wing camber and the and of attack of a wing. Close to the ground, vortices tend to move laterally
This increases wing lift and also increases induced drag. a cross wind will tend to hold the upwind vortex over the landing runway
a tailwind may move the vortices of a preceding aircraft forward into the
The increases drag enables the pilot to make steeper approaches to a landing touchdown zone
without an increase in airspeed.
To avoid wake turbulence a pilot should not the point where a receding large
VFR approaches to a landing at night should be make the same as during the
aircraft touched down and then land past that point
daytime
On takeoff, lift should be accomplished prior to reaching the rotation point
of a preceding large aircraft
the flight path should then remain upwind and above the preceding
aircrafts flight path
 Communication Procedures
Phraseology, Techniques, and Procedures
Automatic Terminal Information Service (ATIS) is a continuous broadcast of non-
control information in selected high-activity terminal areas.
To relieve frequency congestion, pilots are urged to listen to ATIS, an on initial
contact to advise controllers that the information has been received by repeating
the alphabetical code word appended to the broadcast: "information Sierra received"

The phrase "have numbers" does not indicate receipt of the ATIS broadcast

When transmitting an altitude to ATC (up to but not including 18,000ft MSL),
state the separate digits of the thousands, plus the hundreds.

13,500 "one three thousand five hindered"

4,500 "four thousand five hundred"

At airports with air traffic control towers (ATCT), approval must be

obtained prior to moving an aircraft onto the movement area

Ground control frequencies are provided to reduce congestion on the

tower frequency.
They are used for issuance of taxi information, clearances and
other necessary contacts
If instructed by ground control to "taxi to" a particular runway,
the pilot must stop prior to crossing any runway
A clearance must be obtained prior to crossing any runway
Aircraft arriving at an airport where a control tower is in operation
should not change to ground control frequency until directed to do so by
ATC

The key to operating at an airport without an operating control tower is selection

of the correct Common Traffic Advisory Frequency (CTAF)
 The CTAF is identified in appropriate aeronautical publications and on the
Traffic advisories given by a radar service will refer to the other aircraft
sectional chart.
azimuth in terms of the 12-hour clock with 12 o'clock being the
If the airport has a part-time ATCT, the CTAF is usually a tower frequency
flight(track), not the aircraft heading
If a flight service station is located on the airport, they will usually
monitor that frequency and provide advisories when the tower is closed Each hour is equal to 30o
When there is no tower of FSS, UNICOM (if available) is usually the CTAF
an aircraft heading 090o is advised of traffic at the 3 o'clock
UNICOM is limited to the necessities of sage and expeditious operation of
position. The pilot should 90o to the right of the direction of
private aircraft pertaining to runways and wind condition, types of fuel,
flight, or to the south
weather, and dispatching
Communication may be transmitted concerning ground transportation, food,
These radar programs are not to be interpreted as relieving pilots of their
lodging, and services available during transit.
responsibilities to see and avoid other traffic operations in basic VFR weather
When no tower, FSS, or UNICOM is available, use MULTICOM frequency 122.9 for self- conditions to maintain appropriate terrain and obstruction clearance, or to remain
announce procedures in weather conditions equal to or better than the required.

Whenever compliance with an assigned route, heading, and/or altitude is

likely to compromise pilot responsibilities respecting terrain, obstruction
clearance, and weather minimums, the controller should be advised and a
revised clearance or instruction obtained.

Emergency Locator Transmitter (ELT)

Emergency Locator Transmitters (ELT) have been developed as a means of locating
downed aircraft
Transmitting on 121.5 and 406 MHz, the ELT will operate continuously for at least
48 hours

To prevent false alarms the ELT should be tested only during the first 5 minutes of
any hour and only for one to three sweeps.
False alarms can also be minimized by monitoring 121.5 or 406 prior to engine
shutdown at the end of each flight

Non-rechargeable batteries used in ELTs must be replaced when 50% of their useful
life has expired, or when the transmitter has been in use for more than 1
cumulative hour.
Airport Traffic Area Communications and Light Signals
Enroute Flight
Unless otherwise authorized, aircraft are required to maintain two-way radio
communication with the ATCT when operating to, from, or on the controlled airport
Pilotage
regardless of the weather.
If radio contact cannot be maintained, ATC will direct traffic by means of light Air navigation is the art of directing an aircraft along a desired course and being
gun signals able to determine its geographical position at any time. Such navigation may be
accomplished by pilotage, dead reckoning, or using radio navigational aids.

Pilotage is the use of visible landmarks to maintain a desired course, and

is the basic form of navigation for the beginning pilot operating under VFR.

Visible landmarks which can be identified on aeronautical charts allow

the pilot to proceed from one check point to the next

The aeronautical charts most commonly used by VFR pilots are

VFR Sectional Aeronautical Chart

VFR Terminal Area Chart
World Aeronautical Chart

If the aircraft radios fail while inbound to a tower controlled airport the pilot All three charts include aeronautical information such as airports, airways,
should remain outside or above the airport traffic area until the direction and special use airspace, and other pertinent data.

flow of traffic has been determined and then join the airport traffic pattern and
watch the tower for light signals. Latitude run parallel to the equator
From the equator to either pole is 90o (north or south) with 0o being the
The general warning signal (alternating red and green) may be followed by any other equator, north
signal.

For example while on final approach for landing, an alternating red and green Longitude lines are called meridians and are drawn from pole to pole at
light followed by a flashing red light is received from the control tower right angles to the equator.
under these circumstances, the pilot should abandon the approach The prime meridian is used as the zero degree line, passes through Greenwich
realizing the airport is unsafe for landing England

Radar Assistance to VFR Aircraft from this line measurements are made in degrees easterly or westerly
180o
Radar-equipped ATC facilities provide traffic advisories and limited vectoring
(called "basic service") to VFR aircraft, provided the aircraft can communicate Washington DC is about 39o north of the equator and 77o west of the prime meridian
with the facility.
and would be: 39oN 77oW

Stage II service provides radar advisories and sequencing for VFR aircraft. latitude is stated first

Arriving aircraft should initiate contact with approach control.

Approach control will assume Stage II service is requested, unless the pilot In order to describe a location more precisely each degree (o) is subdivided
states that the service is not wanted. into 60 minutes (') and each minute is further divided into 60 seconds ("),
Pilots departing VFR should request Stage II terminal radar advisory services although seconds are not shown.
from ground control on initial contact.
The location (in Oklahoma) can be 35o25'55"N 99o23'15"W
At some locations Stage III service has been established to provide separation
between all participating VFR aircraft and all IFR aircraft in the terminal radar Degrees of west longitude increase from east to west
service area (TRSA) Degrees of north latitude increase from south to north
Unless the pilot states "negative Stage III" on initial contact with approach
control, the service will be provided
 Any attempt to project lines of latitude and longitude onto a flat surface such as
a chart results in a certain amount of distortion.

When plotting a course on a sectional aeronautical chart, this distortion

may be minimized by measuring true course in reference to the meridian
nearest to the halfway point between the departure and the destination.

The straight edge of the plotter has distance scales that match various charts and
these scales may depict both statute and nautical mils.
A small hole at the base of the protractor portion indicates the center of the arc
of the angular scale.
Two complete scales cover the outer edge of the protractor, they are graduated in
degrees.
An inner scale measure the angle from the vertical.

To determine true course (TC), use the plotter in the following manner:

5.1. Using the straight edge of the plotter as a guide, draw a line from the
point of departure to the destination
5.2. Place the top straight edge of the plotter parallel to the plotted
course and move the plotter along the course line as necessary to place
the small center hole over a meridian as near to the halfway point of the
course as possible.
5.3. The true course is the angle measured between the meridian and the
course line
the outer scale is used to read all angles between north through
east to south, and the inner scale is used to read all angles between
south through west to north.

Time 5.4. Course lines which fall within 30o of true north or south can be more
easily measured by sliding the plotter along the course line until the
Time is measured in relation to the rotation of the earth. A day is defined as the hole falls over a horizontal latitude line; use the partial protractor
time required for the earth to make one complete revolution of 360o. Since the day scale for these measurement

is divided into 24 hours, the earth revolves at the rate of 15o each hour.
Thus longitude may be expressed as either 90o or 6 hours west of Greenwich Magnetic Variation
The north pole where all meridians converge is true north.
Twenty-four time zones have been established. Each time zone is 15o of
longitude in width, with the first zone centered on the meridian of Greenwich.
These two poles are not in the same place. At any point where magnetic north and
Each zone uses the local time of its central meridian
true north are in line with each other, the compass needle points both to magnetic
north and coincidently true north.
The line along which this occurs is known as the agonic line.
When positioned west of agonic line, a compass will pint left(west) of true north.
This angular difference between true north and magnetic north is called magnetic
variation (VAR). West of the agonic line, variation is "easterly" East of the
agonic line, variation is "westerly"

The amount of variation is depicted on sectional charts as dashed magenta colored

line connecting points of equal variation called isogonic lines

A course measured on a sectional chart is a true course:

it is measured from a meridian, which runs from the south pole to the
north pole.
Since a magnetic compass is used to maintain a course while flying,
this true course must now be converted to a magnetic course.
This conversion is made by either adding or subtracting the
variation
To convert a true course to a magnetic course, subtract easterly
variation, and add westerly variation: "East is least, west is best"

True course +/- Variation = Magnetic Course +/- Deviation = compass course

Wind and Its Effects

Topography An additional computation, common to both pilotage and dead reckoning, is necessary
to compensate for the effect of wind.
A VFR Sectional Aeronautical Chart is a pectoral representation of a portion of the
Earth's surface upon which lines and symbols in a variety of colors represent
Wind direction is reported as the direction from which the wind blows
features and/or details that can be seen on the Earth's surface.
Wind blowing from the west to the east is a west wind
Contour lines, shaded relief, color tints, obstruction symbols, and maximum
Wind speed is the rate of motion without regard to direction
elevation figures are all used to show topographical information.

Dead Reckoning Downwind movement is with the wind

Upwind movementis against the wind
Dead reckoning is the method used for determining position with a heading indicator
and calculations based on speed, elapsed time, and wind effect from a known If a powered aircraft is flying in a 20-knot wind, it will move 20 nautical
position. miles downwind in 1 hour in addition to its forward movement through the
The instruments used for dead reckoning navigation include the outside air air.
temperature gauge, the airspeed indicator, the altimeter, the clock, and the
magnetic compass system of slaved gyro system. The sideward displacement of an aircraft caused by wind is called drift.
These instruments provide information concerning direction , airspeed, altitude,
and time and must be correctly interpreted for successful navigation. Drift can be determined by measuring the angle between the heading(the
direction the nose is pointing) and the track(the actual flight path of the
Plotting Course aircraft over the earth)

A course is the direction of flight measured in degreed clockwise from north.

Meridians of longitude run from the south pole to the north pole. This alignment is
called true north.

When a course is plotted on a chart in relation to the lines of longitude

and/or latitude it is called a True Course (TC) and will be expressed in three
digits
North may be either 360o or 000o
East is 090o
South is 180o
West 270o
Any course, true, magnetic, or compass, becomes a heading when it is corrected for
wind:

Wind Triangle
True course is determined by measuring the course on an aeronautical chart.

True airspeed is known by applying the appropriate correction to the indication of

the indication of the airspeed indicator.

Wind direction and velocity are known from reports or forecasts from the Flight
Service Stations

The true heading and the ground speed can be found by drawing a wind triangle of
vectors.

One side of the triangle is the wind direction and velocity

One side of the triangle is the true heading and true airspeed
The final side is the track, or true course, and the ground speed
Each side of a wind triangle is the vector sum of the other two sides
Flight Computer (E6-B)
 Static (atmospheric) pressure is taken from the static vents and is
provided to all three instruments
clogging of the static vents or line will cause all three
instruments to become inoperative or to display erroneous readings
Impact (ram) pressure is taken from the pitot tube and furnished to
the airspeed indicator only
clogging of the pitot opening will not affect the operation of the
altimeter or vertical speed indicator

Airspeeds and the Airspeed Indicator

Flight Instruments
Pitot-Static Instruments
The pressure altimeter, vertical-speed indicator, and airspeed indicator operate in
response to pressures through the pitot-static system
 Prior to takeoff the altimeter should be set to the current local
altimeter setting.
After takeoff the altimeter should remain set to the current local
altimeter setting until climbing through 18,000 feet MSL, at that time
the altimeter should be set to 29.92
To compensate for the effect of nonstandard conditions, the altimeter
must be set to the altimeter setting of a station within 100 NM of the
aircraft (unless above 18,000 MSL)

Indicated Airspeed ( IAS ): the uncontrolled reading obtained from the airspeed
indicator
Calibrated Airspeed ( CAS ): indicated airspeed corrected for installation and
instrument error
True Airspeed ( TAS ): calibrated airspeed corrected for temperature and
pressure variations
White arc: flap operating range. Lower limit represents full flap stall
speed. Upper limit provides maximum flap speed. Approaches and landings at
speeds in white arc
Green arc: normal operating range
Yellow arc: caution range
Red line: never-exceed speed

A number of airspeed limitation abbreviated "V" speeds are indicated by

color-coded marking in the airspeed indicator:

VSO: stall speed or minimum steady flight speed in the landing

configuration (the lower limit of the white arc)
VFE: maximum flap extended speed (upper limit of the white arc). The
entire white arc defines the flap operating range
VS1: the stall speed or minimum steady flight speed in s specified
configuration (lower limit of the green arc). The entire green arc
defines the normal operating range
VNO: the maximum structural cruising speed (the upper limit of the
green arc and lower limit of the yellow arc). The yellow arc defines the
caution range, which should be avoided unless in smooth air
VNE: never exceed speed (the upper limit of the yellow arc) marked in
red
VLE: the maximum landing gear extended speed
VA: the design maneuvering speed. If rough air or sever turbulence is
encountered, airspeed should be reduced to maneuvering speed or less to
minimize stress on the airplane structure
VY: the best rate-of-climb speed (the airspeed that will result in the
most altitude in a given period)
VX: the best angle-of-climb speed (the airspeed that will result in the
most altitude in a given distance)

The Altimeter and Altitudes

The altimeter is an instrument used to measure height (altitude) by responding to
atmospheric pressure changes

Altitude: elevation with respect to any assumed reference level and different
term identify the reference level used
Indicated altitude: the altitude read on the altimeter after it is set to the
current local altimeter setting
Absolute altitude: the height above the surface
True altitude: the true height above Mean Sea Level (MSL)
Pressure altitude: the altitude that is indicated whenever the altitude
setting dial is adjusted to 29.92 The Standard Datum Plane, may be above, at or
below sea level
Density altitude: the pressure altitude corrected for nonstandard temperature
and/or pressure
rotating the setting knob on the altimeter simultaneously rotates the
setting dial and the altimeter hands at a rate of one inch per 1000 feet of
altitude.
increasing the setting dial from 29.15 to 29.85 would cause the hands of
the altimeter to show an increase of 700 feet
 On sectional aeronautical charts, VOR location are shown by blue symbols
centered in a blue compass rose which is orientated to Magnetic North.

A blue identification box adjacent to the VOR symbol lists the name
and the frequency of the facility, its 3-letter identifier and Morse Code
equivalent, and other appropriate information

Some VORs have a voice identification alternating with the Morse Code
identifier.
absence of the identifier indicated the facility is unreliable or
undergoing routine maintenance
in either case it should not be used for navigation
Sone VORs also transmit a T-E-S-T code when undergoing maintenance
The VOR station continuously transmits navigation signals providing 360
magnetic courses to to radials from the station.
courses are TO the station and radials are FROM the station
TACAN, a military system which provides directional guidance, also informs
the pilot of the aircrafts distance from the TACAN station
When a VOR and a TACAN are co-located, the facility is called a VORTAC.
Civil pilots may receive both azimuth and distance information from a
Gyroscopic Instruments VORTAC
At some VOR sites additional equipment has been installed to provide pilots
Attitude Indicator
with distance information
The attitude indicator is uses to reference the aircrafts pitch and bank against an such an installation is called VOR/DME (distance measuring equipment)
artificial horizon
VOR Orientation
Turn Coordinator
The Omni Bearing Selector (OBS) is an azimuth dial which can be rotated to select a
The turn coordinator uses a miniature airplane to provide information concerning course or to determine which radial the aircraft is on.
the rate of roll and rate of turn
The TO/FROM indicator shows whether flying the selected course would take
Simultaneously the quality of turn, or movement about the yaw axis, is indicated by the aircraft to or from the VOR station
the ball of the inclinometer
A TO indication shows the radial selected is on the far side of the
Heading indicator VOR station
A FROM indication means the aircraft and the selected course are on
The heading indicator (HI) (directional gyro DGH) informs the pilot of the the same side
aircrafts heading
The Course Deviation Indicator (CDI) when centered, indicated the aircraft is on
The heading indicator must be periodically realigned with the magnetic compass
the selected course, or, when not centered, whether that course is to the left or
during straight-and-level unaccelerated flight
right of the aircraft.

Magnetic Compass
The magnetic compass is attracted to a magnetic field in the earth, so it point
down as well as north. This downward pointing tendency is called magnetic dip and
causes errors in compass indications

When turning toward north from an easterly or westerly heading, the compass
lags behind the actual aircraft heading

When a turn is initiated while on a northerly heading the compass first

indicates a turn in the opposite direction.
The compass lags whenever turns are made to or from north

When turning toward south from an easterly or westerly heading the compass
leads the actual aircraft heading

When a turn is initiated while on a southerly heading the compass shows an

immediate lead in the same direction as the turn. The compass leads whenever
turns are made to or from south

When accelerating or decelerating while heading either east or west the

compass will indicate a turn north
While decelerating it will indicate a turn south

Navigation
VHF Omnidirectional Range (VOR)
The VOR is the backbone of the National Airway system, and this radio aid to
navigation (NAVAID) provides guidance to pilots operating under VFR as well as IFR.
 The following indicates that a course of 030o would take the aircraft to the
selected station, and to get on that course, the aircraft would have to fly
to the left of 030o

VOR Airways
The routes established between VORs are depicted by blue-tinted bands showing the
airway number following the letter "V" and are a called Victor airways

When approaching a VOR where airways converge a pilot must exercise extreme
vigilance for other aircraft
In addition when climbing or descending VFR on an airway, it is considered good
operating practice to execute gentle banks left and right for continuous visual
scanning of the airspace

VOR Receiver Check Points

VOR receiver accuracy may be checked by means of a VOR Test Facility (VOT), ground
check points, or airborne check points

VOTs transmit only the 360o radial signal. Thus when the OBS is set to 360o, the
CDI will center with a FROM indication; while the reciprocal 180o will cause the
CDI to center with a TO indication
An accuracy factor of +/- 4o is allowed when using a VOT facility

Global Positioning System (GPS)

GPS is a United States satellite-based radio navigational, positioning, and time
transfer system operated by the DOD.

The system provides highly accurate position and velocity information and precise
time on a continuous global basis to an unlimited number of properly-quipped user.

The GPS constellation of satellites is designed so that a minimum of five are

always observable by a user anywhere on earth.
The GPS receiver uses data from a minimum of four satellites to yield a three
dimensional position (latitude, longitude, and altitude) and time solution

The GPS receiver verifies the integrity (usability) of the signals received from
the GPS satellites through receiver autonomous integrity monitoring (RAIM) to
determine if a satellite is providing corrupted information.

Without RAIM capability, the pilot has no assurance of the accuracy of the GPS
To determine position in relation to one or more VOR stations:
position.
5.1. tune and identify the selected station. If RAIM is not available, another approach system must be used, another destination
5.2. rotate the OBS until the CDI centers with a from indication selected, or the trip delayed until RAIM is predicted to be available on arrival.
5.3. the OBS reading is the magnetic course from the VOR station to the
aircraft Procedures and Airport Operations
5.4. Repeat the procedure using a second VOR: the aircraft is located at the
point where the two lines of position cross Uncontrolled and Tower-Controlled Airports
Air Traffic Control Towers (ATCT) are established to promote the safe orderly, and
expeditious flow of air traffic.

The tower controller will issue instructions for aircraft to follow the
desired flight path while in the airport traffic area whenever necessary by
using terminology:

The ATCT will also direct aircraft taxing on the surface movement area of the
airport.

In all instances, an appropriate clearance must be received from the tower

before taking off or landing.
Course Determination
At airports without an operating control tower, pilots of fixed-wing and weight
To determine the course to be flown to a VOR station on the sectional chart, first shift control aircraft must circle the airport to the left ("left traffic") unless
draw a line from the starting point to the VOR symbol in the center of the compass visual indicators indicate right traffic
rose.
At the point where the course line crosses the compass rose, read the radial
The course to the station is the reciprocal of that radial
A common visual indicator is the segmented circle system, which consists of
the following components:

Segmented Circle: located in a position readily visible to pilots in

the air and on the ground
Tetrahedron: may be used to indicate the direction of landings and
takeoff. The small end of the tetrahedron points in the direction of
landing.
pilots are cautioned against using the tetrahedron to determine
wind direction, because it may not indicate the correct direction in
light winds
Wind cone, wind sock, wind tree: may be installed near the operation
runway to indicate wind direction.
the large end of the wind cone or sock points into the wind, as
does the cross bar of the wind tee

Airport Markings
Runway numbers and letters are determined from the approach direction.
The number is the magnetic heading of the runway rounded to the nearest 10o

For example , an azimuth of 183o would result in a runway number of 18, a

magnetic azimuth of 076o would result in runway 8
Runway letters differentiate between left (L), right(R), center(C)

The designated beginning of the runway that is available and suitable for
the landing of an aircraft is called the threshold:

A threshold that is not at the beginning of the full-strength runway

pavement is a displaced threshold
The paved area behind the displaced threshold is marked by arrows and
is available for taxiing, takeoff, and landing rollout, but is not to be
used for landing (usually because of an obstruction in the approach path)

The tetrahedron, wind cone, wind sock or wind tee may be located in the
center of the segmented circle and may be lit for night operations
landing runway (landing strip) indicators are installed in pairs and used to
show alignment of runways
traffic pattern indicators are installed in pairs in conjunction with
landing strip indicators and are used to indicate the direction of turns

Stopways are found extending beyond some usable runways.

 these areas are marked by chevrons, and while they appear usable, they
are suitable only as overrun areas
A closed runway which is unusable and may be hazardous, even though it may
appear usable, will be marked by an " X "

LAHSO is an acronym for " Land And Hold Short Operation ".

These operations include landing and holding short of an intersecting runway,

intersecting taxiway, or some other designated point on a runway or taxiway
LAHSO is an ATC procedure that requires pilot participation to balance the
needs for increased airport capacity and system efficiency, consistent with
safety.
Student pilots or pilots not familiar with the LAHSO should not participate
in the program In class B, C, D, or E airspace, operation of the airport beacon during the hours
The pilot in command has final authority to accept or decline any land of daylight often indicates the ceiling is less than 1,00 feet and/or the
and hold short clearance. visibility is less than 3 miles:
The safety and operation of the aircraft remain the responsibility of the
however pilots should not rely solely on the operation of the airport beacon
pilot
to indicate if weather conditions are VFR or IFR
pilots are expected to decline a LAHSO clearance if they determine it
will compromise safety.
Runway Edge Lights are used to outline the runway at night or during periods
Available Landing Distance (ALD) data are published in the special notices
of low visibility. For the most part runway edge lights are white, and may
section of the Chart Supplements U.S. and in the U.S. Terminal Procedures
be high, medium, or low-intensity while taxiways are outlined by blue
Publications.
omnidirectional lights
Pilots should only receive LAHSO clearance when there is a minimum
ceiling of 1,000ft and 3 statute miles visibility.
The intent of having basic VFR weather conditions is to allow pilots
to maintain visual contact with other aircraft and ground vehicle
operation

Radio Control of Lighting is available at some airports, providing airborne

control of lights by keying the aircrafts microphone. The control system is
responsive to the following microphone clicks:

low intensity: 3 times in 5 seconds

medium intensity: 5 times in 5 seconds
highest intensity: 7 times in 5 seconds

Visual Approach Slope Indicator (VASI)

The Visual Approach Slope Indicator (VASI) is a lighting system arranged so as to
provide visual descent guidance information during an approach to a runway.

The lights are visible for up to 5 miles during the day.

The VASI glide path provides obstruction clearance, while lateral guidance is
provided by the runway or runway lights
When operating to an airport with an operating control tower, the pilot of
the airplane approaching to land on a runway served by a VASI is required to
maintain an altitude at or above the glide slope until a lower altitude is
necessary for landing.

Pulsating Visual Approach Slope Indicator (PVASI)

Airport Lighting
Pulsing VASIs normally consist of a single light unit projecting a two-color visual
At night the location of an airport can be determined by the presence of an airport
approach path.
rotating beacon light. The colors and color combinations that denote the type of
airports are: Below-glide path indication is normally red or pulsating red
Above-glide path is normally pulsating white
On-glide path is normally steady white
Precision Approach Path Indicator (PAPI)

The PAPI uses a single row of lights:

 Fitness for Flight
Surface Operations Pilot performance can be seriously degraded by a number of physiological factors.
While some of the factors may be beyond the control of the pilot, awareness of
Taxing to or from the runway generally presents no problems during calm or light
cause and effect can help minimize any adverse effects.
wind conditions.
However , when taxing in moderate to strong wind conditions, the airplane's control
Hypoxia: a state of oxygen deficiency, impairs functions of the brain and
surfaces must be user to counteract the effects of wind. In airplanes equipped with
other organs. Headache, drowsiness, dizziness, and euphoria are all symptoms
nose wheel (tricycle-gear), use the following taxi procedures:
of hypoxia
1. The elevator should be in the neutral position
For optimum protection pilots should avoid flying above 10,000ft MSL
2. The upwind aileron should be held in the up position when taxiing in a cross for prolonged periods without using supplemental oxygen.
wind (or the upwind wing will tend to lift)
Federal Aviation Regulations require that when operating an aircraft
3. The elevator should be held in the down position and the upwind aileron down at cabin pressure altitudes above 12,500ft MSL up to and including
when taxiing with a quartering tailwind 14,000ft MSL , supplemental oxygen shall be used by the minimum flight
crew during that time in excess of 30 minutes at those altitudes
When an airplane equipped with a tailwheel is taxied into a headwind, the elevator
Every occupant of the aircraft must be provided with supplemental
should be held in the up position to hold the tail down.
oxygen above 15,000ft
In a quartering tailwind, both the upwind aileron and the elevator should be in the
down position.
Aviation-breathing oxygen should be used to replenish an aircraft oxygen system for
high-altitude flight.
Oxygen used for medical purposes or welding normally should not be used because it
may contain too much water. The excess water could condense and freeze in oxygen
lines when flying at high altitudes. This could block oxygen flow. Also , constant
use of oxygen containing too much water may cause corrosion in the system

Specifications for "aviators breathing oxygen" are 99.5% pure oxygen, and not
more than 0.005 mg of water per liter of oxygen

Hyperventilation: a deficiency of carbon dioxide within the body, can be the

result of rapid or extra deep breathing due to emotional tension or anxiety
or fear.

Symptoms will subside after the rate and depth of breathing are
brought under control.
A pilot should be able to overcome the symptoms or avoid future
occurrences of hyperventilation by talking aloud, breathing into a bag,
or slowing the breathing rate

Carbon Monoxide Poisoning: Carbon monoxide is a colorless, odorless, and

tasteless gas contained in exhaust fumes.

Symptoms of carbon monoxide poisoning include headache, drowsiness, or

dizziness.
large accumulations of carbon monoxide in the human body result in a
loss of muscular power
susceptibility increases as altitude increases
A pilot who detects symptoms of carbon monoxide poisoning should
immediately shut off the heater and open the air vents

Various complex motions, forces, and visual scenes encountered in flight may result
in misleading information being sent to the brain by various sensory organs.
Spatial disorientation may result if these body signals are used to interpret
flight attitude.
The best way to overcome spatial disorientation is by relying on the flight
instruments rather than taking a chance on the sensory organs.

Aeronautical Decision Making

The pilot is responsible for determining whether they are fit to fly for a
particular flight.
Most preventable accidents have one common factor: human error, rather than a
mechanical malfunction.
Good aeronautical decision making (ADM) is necessary to prevent human error.
ADM is a systematic approach to the mental process used by aircraft pilots to
consistently determine the best course of action in response to a given set of
circumstances.

The ADM process address all aspects of decision making in the cockpit and
identifies the steps involved in good decision making:

1. Identifying personal attitudes hazardous to safe flight

2. Learning behavior modification techniques
3. Learning how to recognize and cope with stress
4. Developing risk assessment skills
Chart Supplements U.S. (previously A/FD) 5. Using all resources in a multicrew situation
6. Evaluating the effectiveness of ones ADM skills
The chart supplements U.S. is a publication designed primarily as a pilots
operational manual containing all airports, seaplane bases, and heliports open to Dangerous Tendencies
the public including communications data, navigational facilities, and certain
special notices and procedures Peer Pressure: poor decision making basked upon emotional response to peers
rather than evaluating a situation objectively
Directories are reissued in their entirety each 56 days

Mind Set: the inability to recognize and cope with changes in the situation
different from those anticipated or planned
 When a pilot recognizes a thought as hazardous, the pilot should label that thought
Get-There-Itis: this tendency, common among pilots, clouds the vision and
impairs judgement by causing a fixation on the original goal or destination as hazardous, then correct that thought by stating the corresponding antidote

combined with a total disregard for any alternative course of action Good cockpit stress management begins with a good life stress management. The
following checklist outlines some thoughts on cockpit stress management:
Duck-Under Syndrome: The tendency to sneak a peak by descending below
minimums during an approach 1. Avoid situations that distract you from flying the aircraft
2. Reduce your workload to reduce stress levels. This will create a proper
Based on the belief that there is always a built in "fudge" factor environment in which to make good decisions
that can be used or on an unwillingness to admit defeat and shoot a 3. If an emergency does occur, be calm. Think for a moment, weigh the
missed approach alternatives, then act
4. Maintain proficiency in your aircraft; proficiency builds confidence.
Scud Running: Pushing the capabilities of the pilot and the aircraft to the Familiarize yourself thoroughly with your aircraft, its systems and emergency
limits by trying to maintain visual contact with terrain while trying to procedures
avoid physical contact with it 5. Know and respect your own personal limitations
6. Do not let little mistakes bother you until they build into a big thing. Wait
This attitude is characterized by the old pilots joke "if its too bad until after you land, then "debrief" and analyze past actions
to go IFR we'll go VFR
7. If flying is adding to your stress either stop flying or seek professional help
to manage stress.
Continuing Visual Rules (VFR): into instrument conditions often leads to
spatial disorientation of collision with ground/obstacles. DECIDE Model
It is even more dangerous if the pilot is not an instrument qualified or
The DECIDE model is intended to provide the pilot with a logical way of approaching
current
decision making:

Getting Behind the Aircraft: Allowing events or the situation to control 1. Detect that a change has occurred
your actions rather than the other way around 2. Estimate what is needed to counter or react to the change
3. Choose a desirable outcome (in terms of success) for the flight
Characterized by a constant state of surprise at what happens next
4. Identify actions which could successfully control the change
5. Do the necessary action
Loss of Positional or Situational Awareness: Another case of getting behind 6. Evaluate the effect(s) of the action countering the change
the aircraft which results in not knowing where you are, an inability to
recognize deteriorating circumstances, and/or the misjudgment of the rate of Collision Avoidance
deterioration
Vision is the most important body sense for safe flight.
Major factors that determine how effectively vision can be used are the level of
Operating Without Adequate Fuel Reserve: Ignoring minimum fuel reserve
illumination, and the technique of scanning the sky for other aircraft.
requirements, either VFR or IFR, is generally the result of overconfidence,
lack of flight planning, or ignoring the regulations
Atmospheric Haze reduces the ability to see traffic or terrain during
flight, making all features appear to be farther away than they actually are
Descent Below the Minimum Enroute Altitude: The duck-under syndrome
manifesting itself during the enroute portion of an IFR flight In preparation for night flight, the pilot should avoid bright while lights for at
least 30 minutes before the flight
Flying Outside the Envelope: Unjustified reliance on the (usually mistaken)
belief that the aircraft's high performance capability meets the demands
imposed by the pilots (usually overestimated) flying skills

Neglect of Flight Planning, Preflight Inspections, Checklists, etc: Scanning the sky for other aircraft is a key factor in collision avoidance.
Unjustified reliance on the pilot's short and long term memory, regular
Because the eyes focus only on a narrow viewing area, effective
flying skills, repetitive and familiar routes, etc.
scanning is accomplished with a series of short, regularly spaced eye
movements
Each movement should not exceed 10o and each area should be observed
for at least 1 second.
At night, scan slowly to permit the use of off-center vision

Prior to starting any maneuver, a pilot should visually scan the entire area for
collision avoidance.

Any aircraft that appears to have no relative motion and stays in one scan quadrant
is likely to be on a collision course.

If a target shows neither lateral nor vertical motion, but increases in size, take
evasive action.

When climbing or descending VFR on an airway, execute gentle banks, right and left
to provide for visual scanning of the airspace
Each ADM student should take the Self-Assessment Hazardous Attitude Inventory Test
in order to gain a realistic perspective on their attitudes toward flying. Aircraft Lighting
The inventory test requires the pilot to provide a response which most accurately
When an aircraft is being operated during period from sunset to sunrise (except in
reflects the reasoning behind their decision
Alaska) it must display lighted position lights and anti-collision lights.
The pilot must choose one of the five reasons given for making a decision, even
The anti-collision light may be either aviation red or aviation white
though the pilot may not consider any of the five choices acceptable.
The inventory test presents extreme cases of incorrect pilot decision making in an
effort to introduce the five types of hazard attitudes:

1. Antiauthority (don't tell me): This attitude is found in people who do not like
anyone telling them what to do. The attitude for this attitude is Follow the
rules, they are usually right.
2. Impulsivity (do something quickly): Is the attitude of people who frequently
feel the need to do something "anything" immediately. The antidote for this
attitude is Not so fast. Think first.
3. Invulnerability (it won't happen to me): Many people feel that accident happen
to others, but never to them. The antidote for this attitude is It could happen
to me
4. Macho (I can do it): Pilots who are always trying to prove that they are better
than anyone else. The antidote for this attitude is Taking chances is foolish
5. Resignation (What's the use): Pilots who think "what's the use?" do not see
themselves as being able to make a great deal of difference in what happens to
them. The antidote for this attitude is I'm not helpless, I can make a
difference

Hazardous attitudes which contribute to poor pilot judgement can be effectively

counteracted by redirecting that hazardous attitude so that appropriate action can
be taken.
 Pilot Certificate Privileges and Limitations
The holder of a student pilot certificate is limited to solo flights or
flights with an instructor
A private pilot has limited solo privileges, and may carry passengers or
cargo as long as the flying is for the pilots pleasure or personal business and
is not done for hire
A private pilot may not pay less than the pro rata share of the operating
expenses of a flight with passengers, provided the expenses only involve fuel,
oil, airport expenditures, or rental fees
the only time passengers may pay for the entire flight is is a donation
is made by the passengers to the charitable organization which is sponsoring
the flight
Commercial pilots may fly for compensation or hire
Airline Transport Pilot may act as pilot-in-command of airline and scheduled
commuter operations
All pilot certificates are valid unless surrendered, superseded or revoked

Pilot Ratings
Category: a broad classification of aircraft such as airplane, rotorcraft,
glider, and lighter-than-air
Class: classification within a category
single-engine, multi-engine, land, water
Type: specific make and basic model of aircraft
a type rating must be held by the pilot in command of large aircraft;
more than 12,500 pounds maximum takeoff weight
all turbojet-powered airplanes require PIC to have a type rating
For IFR an instrument rating is required

Medical Certificates

Basic med - if you have previously held a medical certificate that was not
suspended, revoked, or withdrawn a pilot can act as PIC for noncommercial flights
Regulations with a drivers license. Must complete CMEC within 24 months and physical within
last 48 months. When operating under BasicMed, pilots are limited to:
14 CFR Part 1: definitions and abbreviations of many terms commonly used in
aviation fly with no more than 5 passengers
night means the time between the end of evening civil twilight and the fly an aircraft with a maximum certified takeoff weight of no more than 6,000
beginning of morning civil twilight lbs
14 CFR Part 61: Certification: pilots, flight instructors and ground fly an aircraft that is authorized to carry no more than 6 occupants
instructors flights within the US at an indicated airspeed of 250 knots or less, and at
prescribes requirements for issuing pilot and and flight instructor an altitude at or below 18,000 feet mean sea level (MSL)
certificates and ratings, the conditions of issue, and the privileges and may not fly for compensation or hire
limitations of those certifications
14 CFR Part 91: General Operating and Flight Rules
describes rules governing the operation of aircraft within the US
The National Transportation Safety Board (NTSB) has established rules and
requirements for notification and reporting of aircraft accidents and
incidents.
NTSB Part 830

The definition of nighttime is the time between the end of civil twilight and the
beginning of morning civil twilight.
 High-Performance Airplanes
No person holding a Private or Commercial Pilot Certificate may act as PIC of an
airplane that has more than 200 horsepower's, unless they have received instruction
from an authorized flight instructor who has certified in their logbook that they
are competent to pilot a high-performance airplane

Glider Towing
A private pilot may not act as PIC of an aircraft towing a glider unless at least
100 hours of pilot flight time is logged in the aircraft category, class and type
or 200 hours total pilot time

also within the preceding 24 months they have made at 3 actual/simulated

glider tows while accompanied by a qualified pilot or has made 3 flights as PIC
of a towed glider

Change of Address
If a pilot changes their permanent mailing address without notifying the FAA
Airmens Certification Branch, in writing within 30 days, then they may not exercise
the privileges of their certificate

Responsibility and Authority of the Pilot-in-Command

The PIC of an aircraft is directly responsible and is the final authority for the
safety and operation of that aircraft.

Should an emergency require immediate action, the PIC may deviate from 14 CFR Part
91 to the extent necessary in the interest of safety.

upon request a written report of any deviation from the rules must be sent to
the Administrator

If a pilot receives a clearance that would cause a deviation from a rule,

they should query the controller and request that the clearance be amended

Preflight Action
Before beginning a flight the PIC is required to become familiar with all available
information concerning that flight. This information must include the following:

Third-Class Medical expires at the end of: Runway lengths

Takeoff and landing information for airports of intended use, including
The 60th month after the month of the date of the examination shown on the
aircraft performance data
certificate if the person has not reached his/her 40th birthday on or before
the date of the examination
If the flight will not be in the vicinity of the departure airport, the pilot must
The 24th month after the month of the date of examination shown on the
also consider the following:
certificate if the per has reach their 40th birthday
weather reports and forecasts

Second class medical may exercise the commercial privileges during the first (6 or fuel requirements
12 months) calendar months, and private pilot privilege during the following (12 or enough fuel to fly to the first point of intended landing, and at normal
48) months cruising speed, to fly after that for at least 30 minutes if during the day,
or for at least 45 minutes at night
First class medical may exercise ATP privileges (first class) 6 or 12 months, 12 alternatives available if the flight cannot be completed as planned
months from the date of the examination with second class, and 2 or 5 years with
third class Seatbelts
Required Certificates All required flight crewmembers must remain in their seats with seatbelts
secured during the entire flight unless absent in connection with duties or
When acting pilot-in-command a pilot must have in their possession ore readily
physiological needs. When shoulder harnesses are installed they must be used
accessible in the aircraft:
during takeoffs and landings
current pilot license
photo ID Prior to takeoff, the PIC must ensure that each person on board has been briefed on
current medical certificate the use of seatbelts.

A pilot must present their pilot license and medical for inspection upon request of In addition they must ensure that the passengers are notified to fasten their
any FAA, NTSB, or federal, state, or local law enforcement officer seatbelts during taxi, takeoffs, and landings. A child who has not reached their
second birthday may be held by an adult who is occupying a seat or berth
Recent Flight Experience
Alcohol and Drugs
No person may act as PIC of an aircraft unless within the preceding 24 calendar
months they have accomplished a flight review No person may act as a crewmember on an aircraft under the following conditions:

Within 8 hours after the consumption of any alcoholic beverage

Flight Review: This review is given in an aircraft for which the pilot is
While under the influence of alcohol (0.04 percent by weight or more alcohol
rated by an appropriately rated instructor or other person designated by the
in the blood)
FAA.
While using any drug that affects their faculties in any way contrary to
A logbook entry will document satisfactory accomplishment of this safety
requirement.
If the pilot takes a proficiency check (as for a certificate or a new Except in an emergency, no pilot of an aircraft may allow a person who
rating) is counts for the flight review appears to be intoxicated or under the influence of drugs (except a medical
patient under proper care) to be carried in that aircraft

No person may act as PIC of an aircraft carrying passengers unless

A conviction for the violation of any law relating to drugs or alcohol is grounds
within the preceding 90 days they have made 3 takeoffs and 3 landings as
the sole manipulator of the controls in an aircraft of the same category, for:
class, and if a type rating is required in the same type
1. Denial of an application for any certificate, rating, or authorization issued
touch and go landings are acceptable unless the passengers are to
under part 61 for a period of up to 1 year after the date of final conviction
be carried in a tailwheel airplane, in which case the landing must
2. Suspension or revocation of any certificate, rating, or authorization issued
come to a full stop
under Part 61
If passengers are to be carried during the period from 1 hour after
Pilots should provide a written report of each alcohol-or-drug-related motor
sunset to 1 hour before sunrise, the PIC must have made within the
vehicle action to the FAA, Civil Aviation Security Division (AMC-700) no later
preceding 90 days, at least 3 takeoffs and 3 landings during that period.
than 60 days after the motor vehicle action
The landing must have been to a full stop and in the same category and
class of aircraft to be used
Right-of-Way Rules
When weather conditions permit, vigilance must be maintained so as to see and avoid
other aircraft.

An aircraft in distress has the right-of-way over all other air traffic.
When aircraft of the same category are converging at approximately the same
altitude (except head-on, or nearly so) the aircraft on the other's right
has the right-of-way

An aircraft towing or refueling other aircraft has the right of way over all other
engine driven aircraft

When aircraft are approaching each other head-on or nearly so, each pilot of each
aircraft (regardless of category) shall alter course to the right

An aircraft being overtaken has the right-of-way. The overtaking aircraft shall
alter course to the right to pass well clear

When two or more aircraft are approaching an airport for landing, the aircraft at
the lower altitude has the right-of-way, but it shall not take advantage of this
rule to cut in front of or overtake another aircraft

Parachutes
If any passengers are carried the pilot of an aircraft may not intentionally exceed
60 degree of bank or 30 degree pitch unless each occupant is wearing an approved
parachute

This requirement does not apply when a CFI is giving instruction in spins or any
other flight maneuver required by regulations for a rating

Deviation from Air Traffic Control Instructions

An ATC clearance is authorization for an aircraft to proceed under specified
traffic condition within controlled airspace.

When an ATC clearance has been obtained, no PIC may deviate from that clearance
except in an emergency, unless they obtain an amended clearance.

If a pilot does deviate from a clearance or ATC instruction during an

emergency, they must notify ATC of the deviation as soon as possible
If in an emergency a pilot is given priority over other aircraft by ATC, they
may be requested to submit a detailed report even though no deviation from a
rule occurred
the requested report shall be submitted within 48 hours to the chief of
the ATC facility which granted the priority

Minimum Safe Altitudes

No minimum altitude applies during takeoff or landing.
During the other phases of flight the following minimum altitudes apply:

Anywhere: the pilot must maintain an altitude which, in the event of an

engine failure, will allow an emergency landing without undue hazard to persons
or property on the surface
If the aircraft are of different categories, the following applies:
Over congested areas: an altitude of at least 1,000ft above the highest
A balloon has the right-of-way over any other category aircraft obstacle within a horizontal radius of 2,000 feet of the aircraft must be
A glider has the right-of-way over an airship, airplane, rotorcraft, weight- maintained over any congested area of a city, town or settlement or over any
shift control, or powered parachute open air assembly of people
An airship has the right of way over an airplane, rotorcraft, weight shift Over other than congested areas: an altitude of 500ft above the surface must
control or powered parachute be maintained except over open water or sparsely populated areas.
in that case the aircraft may not be operated closer than 500ft to any
person vessel, vehicle, or structure
Basic VFR Weather Minimums
Rules governing flight under Visual Flight Rules (VFR) have been adopted to assist
the pilot in meeting their responsibility to see and avoid other aircraft

In addition, when operating within the lateral boundaries of the surface are
of Class B, C, D, or E airspace designated for an airport, the ceiling must
not be less than 1,000ft. Special VRF Weather Minimums
If the pilot intends to land, take off, or enter a traffic pattern within
If an appropriate ATC clearance (Special VFR) has been received an aircraft may be
such airspace, the ground visibility must be at least 3 miles at that
operated within the lateral boundaries of the surface area of Class B, C, D, or E
airport
airspace designated for an airport when the ceiling is less than 1,000 ft and/or
If ground visibility is not reported, 3 miles flight visibility is required
the visibility is less than 3 miles
in the pattern
Special VFR requires the aircraft to be operated clear of the clouds with
flight visibility of at least 1 statute mile
For special VFR operating between sunset and sunrise, the pilot must hold an
instrument rating and the airplane must be equipped for instrument flight
Requests for Special VFR arrival or departure clearance should be directed to
the airport traffic control tower if on is in operation

VFR Cruising Altitudes

When operating an aircraft under VFR in level cruising flight more tan 3,000ft
above the surface and below 18,000ft MSL a pilot is required to maintain an
appropriate altitude in accordance with certain rules.

This requirement is called the Hemispherical Cruising Rule and is based on magnetic
course nor magnetic heading.

When operating below 18,000ft MSL in VFR cruising flight with more than
3,000ft above the surface and on a magnetic course of 0o through 179o any odd
thousand-foot MSL altitude plus 500ft (3,500 , 5,500) is appropriate
On a course of 180o through 359o even thousands plus 500ft (4,500, 6,500) is
appropriate

Categories of Aircraft
The term category when used with respect to the certification of aircraft, means a
grouping of aircraft based upon intended use or operating limitation:

normal
utility
aerobatic
restricted
experimental
transport
 limited Maintenance and Inspections
provisional
The owner or operator of an aircraft is primarily responsible for
Both restricted and experimental category aircraft are prohibited from carrying
maintaining that aircraft in an airworthy condition, including compliance
persons or property for compensation or hire.
with airworthiness directives. They are also responsible for all records of
In addition both categories are normally prohibited from flying over densely
maintenance, repairs and alteration
populated areas or in congested airways.
(The PIC is responsible for determining that the aircraft is in an airworthy
condition prior to flight)
Formation Flight and Dropping Objects
The airworthiness of an aircraft can be determined by a preflight inspection
Flying so close to another aircraft as to crate a collision hazard is prohibited. and a review of the maintenance records
If the intent is to fly formation, prior to arrangement with the PIC of each
aircraft is required. The holder of a pilot certificate is allowed (within certain limits) to
perform preventative maintenance on any aircraft owned and operated by that
In any case, no person may operate an aircraft carrying passengers for in hire in
pilot.
formation flight.
Preventative maintenance is limited to tasks such as replacing
The PIC of an aircraft may not allow any object to be dropped while in flight
defective safety wiring, servicing landing gear wheel bearings, replacing
unless reasonable precautions are taken to avoid injury or damage to persons or
safety belts, and other tasks listed in 14 CFR Part 43 appendix A
property on the surface.
After preventative maintenance has been performed on an aircraft the
signature, certificate type and certificate number of the person
VFR Flight Plans approving the aircraft for return to service, and a description of the
work, must be entered in the aircraft maintenance records
Although filing a VFR flight plan is not mandatory (except under certain
circumstances) it is considered good operating practice.
An aircraft may not be operated unless, within the preceding 12 calendar
The pilot must close a VFR flight plan at the completion of a flight.
months, it has had an annual inspection and has been approved for return to
This can be done by contacting the FAA upon landing. service.
This will be indicated by the appropriate notation in the aircraft
Speed Limits maintenance records.
The following maximum speed limits for aircraft have been established in the To determine the expiration date of the last annual inspection, refer to the
interest of safety: aircraft maintenance records.

1. Below 10,000ft MSL the limit is 250 knots indicated air speed (KIAS) If the aircrafts last annual inspection was performed on July 12, 1993
the next annual inspection will be due no later than midnight, July 31
2. The speed limit within Class B airspace is also 250 KIAS
1994
3. The maximum speed authorized in a VFR corridor through Class Bravo airspace or
in airspace underlying Class B airspace is 200 KIAS
4. In class Delta airspace, aircraft are restricted to a maximum of 200 KIAS If an aircraft is used to carry passengers for hire or used for flight

5. Unless otherwise authorized or required by ATC, no person may operate an instruction for hire, it must have, in addition to the annual inspection, an
aircraft at or below 2,500 feet AGL within 4 NM of the primary airport of a inspection each 100 hours of flight time. (An annual inspection may be
Class C or D airspace area at an indicated airspeed of more than 200 knots substituted for the 100 hour inspection, but a 100hr inspection may not be
substituted for an annual inspection)

The next 100hr inspection should be performed 100 hours after the
previous inspection was due.
a 100hr inspection was due at 3,302.5 hours on the hobbs meter. The
100-hour inspection was actually done at 3,309.5 hours. The next
100hr inspection is due at 3402.5 hours

The transponder cannot be operated unless within the preceding 24 calendar

months it has been inspected and found satisfactory

If an aircraft has been maintained, rebuilt, or altered in any manner that may have
appreciably changed its flight characteristics or operation in flight, no
passengers may be carried until it has been flight tested by an appropriately-rated
pilot (with at least Private Pilot Certificate) and approved for return to service

ADs, ACs, and NOTAMs

Airworthiness Directives (AD)

identify unsafe aircraft conditions and prescribe regulatory actions (such

as inspection or modification) or limitations under which the affected
aircraft may continue to be operated and are mandatory.

Compliance with an applicable Airworthiness Directive must be entered

in the appropriate aircraft maintenance records
The owner operator is responsible for ensuring ADs are complied with.
Pilots may operate an aircraft not in compliance with an AD if the AD
allows for this

Airworthiness
Advisory Circulars
Each aircraft is issued an Airworthiness Certificate, which remain valid as long as
are issued by the FAA to inform the aviation community in a systematic way
the aircraft is maintained and operated as required by regulations.
of non-regulatory material of interest.
This Airworthiness Certificate, along with the Aircraft Registration Certificate,
operating limitation, and weight and balance must be onboard the aircraft during In many cases they are the result of a need to fully explain a
flight: particular subject (wake turbulence for example)
They are issued in a numbered-subject system corresponding to the
A irworthiness
subject areas of the Federal Aviation Regulation, Advisory Circulars
R egistration
(some free, other at cost) may be obtained by ordering from the
O perating Limitations Government Printing Office (GPO)
W eight and Balance

The aircrafts operating limitations may be found in the airplane flight manual, The Aeronautical Information Manual (AIM) is the official guide to basic
approved manual material, markings, and placards, or any combination thereof flight information and ATC procedures. It is updated every 180 days and is
available from the FAA website
 The operator of an aircraft involved in an accident or incident which requires
Notices to Airmen (NOTAMs)
notification of the NTSB is responsible for preserving the wreckage, mail, or cargo
provide the most current information available. until the NTSB takes custody.
These items may be moved to protect the wreckage from further damage
They provide time-critical information on airports and changes that
affect the national airspace system and are of concern to instrument The operator of an aircraft involved in an accident is required to file an accident
flight rule (IFR). report within 10 days.
NOTAM information is classified into 4 categories: A report of an incident must be reported only upon request.
NOTAM (D) or distant
Attached to hourly weather reports and are available at flight Weather
service stations
Flight Data Center (FDC) NOTAMs The Heating of the Earth
Issued by the National Flight Data Center and contain
regulatory information, such as temporary flight restrictions or The major source of all weather is the sun.
an amendment to instrument approach procedures
Changes of weather are caused by the unequal heating of the Earth's surface.
pointer NOTAMs
Highlight or point out another NOTAM such as an FDC or NOTAM The unequal heating of Earths atmosphere creates a large air-cell circulation
(D) pattern (wind) because the warmer air has a tendency to rise (low pressure) and the
This type of NOTAM will assist pilots in cross-referencing colder air has a tendency to settle or descend (high pressure) and replace the
important information that may not be found under an airport or rising warmer air.
NAVAID identifier
military NOTAMs This unequal heating, which causes pressure variations will cause variations
pertain to U.S. Air Force, Army, Marine, and Navy in altimeter setting between weather reporting stations
NAVAIDs/airports that are part of the NAS
Because the Earth rotates, this large, simple air cell circulation pattern
NOTAM-Ds and FDC NOTAMS are contained in the Notices to Airment publication which in greatly distorted by a phenomenon known as Coriolis Force
is issued every 28 days. Prior to any flight pilots should check for any NOTAMs
When the wind first begins to move to higher altitudes, the Coriolis
that could affect their intended flight
Force deflects it to the right (in the Northern Hemisphere) causing it to
An FDC NOTAM will be issued to designate a temporary flight restriction (TFR). flow parallel to the isobars
The NOTAM will begin with the phrase "Flight Restrictions" followed by the location
of the temporary restriction, effective time period, area defined in stature miles
and altitudes affected.
The NOTAM will also contain the FAA coordination facility and telephone number, the
reason for the restriction, and any other information deemed appropriate.
The pilot should check the NOTAMs as part of flight planning.
Some of the purposes for establishing a temporary restriction are:

protect persons and property in the air or on the surface from an existing or
imminent hazard
provide a safe environment for the operation of disaster relief aircraft
prevent an unsafe congestion of sightseeing aircraft above an incident or
event, which may generate a high degree of public interest
protect declared national disasters for humanitarian reason in Hawaii
protect the President, vice-president, or other public figures
provide a safe environment for space agency operation

Accident Reporting Requirements

The National Security Board (NTSB) Part 830 contains rules pertaining to
notification and reporting of aircraft accidents and incident.
Is also addresses preservation of aircraft wreckage, mail, cargo, and records.

Accident: means "an occurrence in which any person suffers death, serious
injury, or in which the aircraft receives substantial damage"

Serious Injury: means any injury which:

requires hospitalization for more than 48 hours commencing within 7
days from the date the injury was received
results in a fracture of any bone (except simple fractures of
fingers, toes, or nose)
causes sever hemorrhages, nerve, muscle, or tendon damage
involves any internal organ
involves second or third degree burns or any burns burns affecting
more than 5 percent of the body surface
Substantial Damage: damage or failure which adversely affects the
structural strength, performance, or flight characteristics of the air
craft and which would normally require major repair or replacement of the
affected component
The following is NOT considered substantial damage
engine failure
bent fairings or cowling
dented skin
small punctured holes in the skin or fabric
ground damage to rotor or propeller blades Circulation and Wind
damage to landing gear, wheels, tires, flaps
The general circulation and wind rules in the Northern Hemisphere are as follows:
engine accessories
brakes 1. Air circulates in a clockwise direction around a high
wingtips 2. Air circulates in a counter-clockwise direction around a low
3. The closer the isobars are together, the stronger the windspeed
The term "incident" means "an occurrence other than accident, which affects or 4. Due to surface friction (up to about 2,000ft AGL), surface winds do not exactly
could affect the safety of operation" parallel the isobars. but move outward from the center of the high toward the
low
Immediate notification of the NTSB is required when an aircraft accident
occurs, and any aspect of a specified list of incidents , which include: Knowing that air flows out of the high in a clockwise direction and into the low in
a counter-clockwise direction is useful in preflight planning.
Inability of a flight crewmember to perform their duties due to
illness or injury
Inflight fire
An aircraft is overdue and believed to have been involved in an
accident
Flight control system malfunction or failure
When aircraft collide in flight or damage of more than $25,000 occurs
to property other than the aircraft
Temperature
In aviation temperature is measured in degrees Celsius.

The standard temperature at sea level is 15oC (59oF).

The average decrease in temperature with altitude is 2oC (3.5oF) per 1,000ft.
Since this is an average, the exact value seldom exists
sometimes it even increases (inversion)
the most common ground or surface based temperature inversion is one
that is produced by terrestrial radiation on a clear, relatively still
night.

Moisture
Air has moisture (water vapor) in it.
The water vapor content if air can be expressed in two different ways.

relative humidity
dew point

Relative Humidity relates the actual water vapor present in the air to which Relative humidity can be increased either by lowering the air temperature or by
could be present in the air.
increasing the amount of moisture in the air.
If the temperature and the dew point spread is small and decreasing condensation is
Temperature largely determines the maximum amount of water vapor air
can hold about to occur.
Warm air can hold more water vapor than cold air If the temperature is above freezing, the weather most likely to develop will be
Air with 100% relative humidity is said to be saturated, less than fog or low clouds
100% is unsaturated
Air Masses and Fronts
Dew point is the temperature to which air must be cooled to become saturated When a body of air comes to rest on, or moves slowly over, an extensive area having
by the water already in the air fairly uniform properties of temperature and moisture, the air takes on these
properties. The area over which the air mass acquires its identifying distribution
of temperature and moisture is its "source region"
As this air mass moves from its source region, it tends to take on the properties

of the new underlying surface. The air trend toward change is called air mass
Moisture can be added to the air by either evaporation or sublimation.
Moisture is removed from the air by either condensation or sublimation modification.

When water vapor condenses on large objects such as airplanes it will form dew and Ridge: an elongated area of high pressure
when it condenses on microscopic particles, clouds or fog forms
Trough: an elongated area of low pressure

all fonts lie in troughs

Cold front: is the leading edge of an advancing cold air mass

Warm front: is the leading edge of an advancing warm air mass

Warm fronts move about half as fast as cold fronts

Frontal waves and cyclones (areas of low pressure) usually form on slow-
moving cold fronts or stationary fronts

The physical manifestations of a warm or cold front can be different with each
front.
They vary with the speed of the air mass on the move and the degree of stability of
the air mass being overtaken.
A stable air mass forced aloft will continue to exhibit stable characteristics,
while an unstable air mass forced to ascend will continue to be characterized by
cumulus clouds, turbulence, showery precipitation and good visibility.

Frontal passage will be indicated by the following discontinuities:

4.1. A temperature change

4.2. A continuous decrease in pressure followed by an increase as the front
passes
4.3. A shift in the wind direction, speed or both
 The first 3 families (low, middle, and high) are further classified
according to the way they are formed:

clouds formed by vertical currents (unstable) are cumulus (heap) and

are billowy in appearance
Clouds formed by the cooling of stable layer are stratus (layered) and
are flat and sheet-like in appearance
A further classification is the prefix "nimbo" or the suffix "nimbus"
which means raincloud

Stability of the Atmosphere

Atmospheric stability is defined as the resistance of the atmosphere to vertical
motion.
A stable atmosphere resists any upward or downward movememnt.
An unstable atmosphere allows an upward or downward disturbance to grow into a
vertical (convective) current.

Determining the stability of the atmosphere requires measuring the difference

between the actual existing (ambient) temperature lapse rate of a given parcel of
air and the dry adiabatic lapse rate (3oC per 1,000ft)

A stable layer of air would be associated with a temperature inversion, warming

from below on the other hand, would decrease the stability of an air mass

Clouds
Stability determines which of two types of clouds will be formed: cumuliform or
stratiform

Cumuliform clouds are the billowy-type clouds having considerable vertical

development, which enhances the growth rate of precipitation.
They are formed in unstable conditions, and they produce showery
precipitation made up of large water droplets High clouds called cirrus are composed mainly of ice crystals therefore they are
least likely to contribute to structural icing (since it requires water droplets)
Stratiform clouds are the flat more evenly based clouds formed in stable
conditions. The base of a cloud (AGL) that is formed by vertical currents (cumuliform
They produce steady continuous light rain and drizzle made up of smaller clouds) can be roughly calculated by dividing the difference between the
raindrops surface temperature and dew point by 4.4 and multiplying the rounded result
by 1,000.
The convergence of the temperature and dew point lapse rate is 4.4oF per
Steady precipitation (in contrast to showery) preceding a front is an
1,000ft
indication of stratiform clouds with little or no turbulence

Clouds are divided into 4 families according to their height:

low
middle
high
clouds with extensive vertical development
 The shear associated with cold fronts is usually found behind the front, if the
What is the approximate base of the cumulus clouds if the surface air
front is moving at 30 knots or more the shear zone will be 5,000 feet above the
temperature is 70oF and the dew point is 61oF
surface 3 hours after frontal passage

Two potentially hazardous situations:

the loss of a tailwind

the loss of a headwind

Tailwind may shear to either a calm or a headwind component

The airspeed initially increases, the aircraft pitches up, and

altitude increases
Lower than normal power would be required initially, followed by a
further decrease as the shear is encountered, and then an increase as the
glide slope is regained
Turbulence
Cumulus clouds are formed by convective currents (heating from below), therefore a A headwind may shear to a calm or tailwind component.
pilot can expect turbulence below or inside cumulus clouds, especially towering
cumulus clouds. Initially the airspeed decreases, the aircraft pitches down, and
altitude decreases
The greatest turbulence could be expected inside cumulonimbus clouds

If severe turbulence is encountered either inside or outside of clouds, the Some airports can report boundary winds as well as the wind at the tower. When a
airplanes airspeed should be reduced to maneuvering speed and the pilot should tower reports a boundary wind which is significant different from the airport wind,
attempt to maintain level flight attitudes because the amount of excess load that there is possibility of hazardous wind shear
can be imposed on the wing will be decreased. Any attempt to maintain a constant
attitude will greatly increase the stresses that are applied to the aircraft

Thunderstorms
Thunderstorms present many hazards to flying. 3 conditions necessary to the
formation of a thunderstorm are:

1. Sufficient water vapor

2. An unstable lapse rate
3. An initial upward boost (lifting)

The initial upward boost can be caused by heating from below, frontal lifting, or
by mechanical lifting (wind blowing air upslope on a mountain)

There are 3 stages of a thunderstorm:

the cumulus
mature
dissipating stages

Cumulus stage: characterized by continuous updrafts, and these

updrafts create low-pressure areas
Mature stage: thunderstorm reach their greatest intensity during this
stage, which is characterized by updrafts and downdrafts inside the cloud
precipitation inside the cloud aids in the development of these
downdrafts and the start of rain from the base of the cloud signals
the beginning of the mature stage.
The precipitation that evaporates before it reaches the ground is
called virga
Dissipating stage: of a thunderstorm is characterized predominantly be
downdrafts

Lighting is always associated with a thunderstorm

Hail is formed inside thunderstorms by the constant freezing, melting, and
refreezing of water as it is carried about by the up and downdrafts

A pilot should always expect the hazardous and invisible atmospheric phenomena
called wind shear turbulence when operating anywhere near a thunderstorm (within 20
NM)

Thunderstorms that generally produce the most intense hazard to aircraft are called
squall-line thunderstorms. These non-frontal, narrow bands of thunderstorms often
develop ahead of a cold front

Embedded thunderstorms are those that are obscured by massive cloud layers and
Icing
cannot be seen
Structural icing occurs on an aircraft whenever supercooled condensed droplets of
Wind Shear water make contact with any part of the aircraft that is also at a temperature
below freezing.
Wind shear is defined as a change in wind direction and/or speed over a very short
distance in the atmosphere. This can occur at any level of the atmosphere and can An inflight condition necessary for structural icing to form is visible
be detected by the pilot as a sudden change in airspeed. moisture (clouds or raindrops)

Low-level wind shear can be expected during strong temperature inversions,

on all sides of a thunderstorm and directly below the cell.
A pilot can expect a wind shear zone in a temperature inversion whenever the
wind speed at 2,000ft to 4,000ft above the surface is 25knots

low level wind shear can also be found near frontal activity because
winds can be significantly different in the two air masses which meet to
form the front

In warm front conditions, the most critical period is before the front passes.

Warm front shear may exist below 5,000ft for about 6 hours before surface
passage of the front
The wind shear associated with a warm front is usually more extreme than that
found in cold fronts
 Icing in precipitation, (rain) is of concern to the VFR pilot because it can
occur outside of the clouds.

Aircraft structural ice will most likely have the highest accumulation
in freezing rain which indicates warmer temperature at a higher altitude

The presence of ice pellets at the surface is evidence that there is freezing rain
at a higher altitude, while wet snow indicates that the temperature at your
altitude is above freezing.

a situation conductive to any icing would be flying in the vicinity of a

front

Aviation Routine Weather Report (METAR)

Type of Report
Fog
METAR: taken every hour
Fog is a surface-based cloud (restricting visibility) composed of either water non-routine (special) aviation weather report SPECI): weather observation
droplets or ice crystals. that is an unscheduled report indicating a significant change in one or more
Fog may form by cooling the air to its dew point or by adding moisture to the air elements
near the ground.
A small temperature/dew point spread is essential to the formation of fog.

An abundance of condensation nuclei from combustion products makes fog prevalent in Station Identifier
industrial areas
Each reporting station is listed by its 4 letter International Civil Aviation
Fog is classified the way it is formed: Organization (ICAO) identifier.

Radiation fog (ground fog): is formed when terrestrial radiation cools the Time of Report
ground, which in turn cools the air in contact with it.
When the air is cooled to its dew point (or within a few degrees), fog The date (day of the month) and time of the observation.
will form The time is given in UTC or Zulu as indicated by a Z.
This fog will form most readily in warm, moist air over low, flatland,
areas on clear, calm (no wind) nights "122150Z" 12th of the month at 2150Z
Advection fog (sea fog): is formed when warm, moist air moves (wind is
required) over colder ground or water (an air mass moving inland from the coast Modifier
in winter)
Upslope fog): is formed when moist stable air is cooled to its dew point as When a METAR is created by a totally automated weather observation station, the
it moves (wind is required) up sloping terrain. modifier AUTO follows the date/time element
cooling will be at the dry adiabatic lapse rate of approximately 3oC per
1,000ft The modifier COR is used to indicate a corrected METAR and replaces a previously
disseminated report.
Precipitation (rain or drizzle)-induced fog is most commonly associated with
frontal activity and is formed by relatively warm drizzle or rain falling
Wind Information
through cooler air.
evaporation from the precipitation saturates the cool air and fog forms. The wind direction and speed are reported in a five digit group, or six digits if
This fog is especially critical because it occurs in the proximity of the speed is over 99 knots.
precipitation and other possible hazards such as icing, turbulence, and
thunderstorms The first 3 digits represent the direction from which the wind is blowing in
Steam fog: forms in the winter when cold, dry air passes from land areas over reference to true North.
comparatively warm ocean waters. The next 2 or 3 digits show the speed in knots (KT)
low level turbulence can occur and icing can become hazardous in a steam Calm winds are reported as 00000KT
fog Gusty winds are reported with a G, followed by the highest gust
If the wind direction varies 60 degrees or more and speed is above 6 knots, a
Frost variable group follows the wind group.
the extremes of wind direction are shown separated by a V
Frost is described as ice deposits formed by sublimation on a surface when the
If the wind is blowing from 020o, varying 090o it is reported as 020V090
temperature of the collecting surface is at or below the dew point of the adjacent
air and the dew point is below freezing

Frost causes early airflow separation on an airfoil resulting in a loss of lift.

Therefore all frost should be removed from the lifting surface of an airplane
before flight or it may prevent the plane from becoming airborne

Weather Services
An international weather reporting code is used for weather reports (METAR) and
forecasts (TAFs) worldwide.

For aviation purposes the ceiling is the lowest broken or overcast layer, or
vertical visibility into an obscuration.
Visibility mist (BR) would be used.
Shallow fog, patches of fog, or partial fog might be coded with prevailing
Prevailing visibility is the greatest distance an observer can see and visibility of 7 statute miles or greater.
identify objects through at least half of the horizon.

When the prevailing visibility varies from one area of the sky to
another, the visibility in the majority of the sky is reported
If visibility varies significantly, the observer can report individual
sector visibilities in the remarks section of the METAR

Visibility is reported in statute miles (SM):

1/2SM indicates one-half statute mile

Runway Visual Range (RVR) might be reported following prevailing visibility.

Weather

Weather or obstructions to vision that are present at the time of the observation
are reported immediately after the visibility in the following order:

1. intensity or proximity Amount of Clouds

2. descriptor
The amount of clouds covering the sky is reported in eighths or octas of sky cover:
3. precipitation
4. obstruction to visibility
5. any other weather phenomena

The intensity or proximity and/or descriptor are used to qualify the precipitation,
obstruction, or other weather phenomena

Qualifier and Descriptor

+TSRA

Intensity or proximity is shown immediately prior to the precipitation codes.

The indicated intensity applies only to the first type of precipitation reported.
Intensity levels are:

light -
moderate no sign
heavy + Clear sky: SKC (manual), CLR automated
Automated stations cannot detect clouds above 12,000ft, a report of clear
Weather obscurations occurring in the vicinity (between 5 and 10 statute miles) of indicates there were no clouds detected below 12,000ft
the airport are shown by the letters VC. FEW: 0 - 2/8
For precipitation, VC applies within 10 statute miles of the observation point. SCT: 3/8 - 4/8 : scattered
VC will not appear if an intensity qualifier is reported BKN: 5/8 - 7/8 : broken
OVC: overcast

Height, Type, and Vertical Visibility

The height of clouds or the vertical visibility into obscuring phenomena is

reported with 3 digits in hundreds of feet above ground level (AGL).

To determine the cloud height, add 2 zeros to the number given in the
report.

When more than one layer is present, the layers are reported in ascending order.
Weather Phenomena Automated stations can only report a maximum of 3 layers at 12,000ft AGL
Human observers can report up to 6 layers of clouds at any altitude
Up to 3 types of precipitation can be coded in a single grouping of present weather
condition, In the example the scattered layer was at 800ft AGL and the overcast layer was at
When more than one is reported, they are shown in order of predominance. 1,200ft AGL, the base of the cumulonimbus clouds is at 1,200ft AGL

Obscurations, which limit visibility are after any reported precipitation. In a manual report a cloud type might be included if towering cumulus clouds (TCU)
Fog (FG) is listed when the visibility is less than 5/8 stature mile. If the or cumulonimbus clouds (CB) are present. The code follows the height of their
visibility were to increase to between 5/8 and 6 statute miles the code for must reported base.
A ceiling is the AGL height of the lowest layer of clouds that is reported as COR : corrected
broken or overcast, or the vertical visibility into an obscuration such as fog or RTD delayed
haze.
Winds and Temperatures Aloft Forecast
Temperature and Dewpoint
A winds and temperatures aloft forecast (FD) provides an estimate of

wind direction in relation to true north

wind speed in knots
and temp in C
The observed air temperature and dewpoint (Celsius) are listed immediately
following the sky condition. 2635-08 indicates the wind is from 260o at 35 knots and the temperature is 8C

In the example it is 20 degrees Celsius and the dew point is 18

If it were below zero the temp is M10, for -10 Celsius

Altimeter

The altimeter setting is reported in inches of mercury in a four-digit group

prefaced by an A

In the example the altimeter setting was reported as 29.95

Remarks

Remarks are RMK

Wind speeds between 100 and 199 knots are encoded so direction and speed can
be represented by 4 digits.
This is done by adding 50 to the two-digit wind direction and subtracting
100 from the velocity
A wind of 270o at 101 knots is encoded as 7701 (27+50=77 for wind direction,
and 101-100=01 for wind speed)

A code of 9900 indicates light and variable winds (less than 5 knots)

Pilot Weather Reports

Inflight Weather Advisories
PIREPs often confirm such information as the height of bases and tops of cloud
Inflight Weather Advisories advise enroute pilots of the possibility of
layers, in-flight visibility, icing conditions, wind shear, and turbulence
encountering hazardous flying conditions that may not have been forecast at the
time of the preflight weather briefing

AIRMETs (WA): contain information on weather that may be hazardous to single

engine, other light aircraft, and VFR pilots

The items covered are moderate icing or turbulence, sustained winds of

30 knots or more at the surface, widespread areas of IFR conditions, and
extensive mountain obscurement

SIGMETs (WS): advise of weather potentially hazardous to all aircraft.

The items covered are severe icing, severe or extreme turbulence, and
widespread sandstorms, dust storms or volcanic ash lowering visibility to
less than 3 miles

SIGMETs and AIRMETs are broadcast upon receipt and 30-minute intervals (H + 15 and
H + 45) during the first hour.
If the advisory is still in effect after the first hour, an alert notice will be
broadcast.

Pilots may contact the nearest FSS to ascertain whether the advisory is pertinent
to their flights

Convective SIGMETs (WST): cover weather developments such as tornadoes,

lines of thunderstorms, and embedded thunderstorms and they also imply
severe or greater turbulence, sever icing, and low-level wind shear.
Terminal Aerodrome Forecast When a SIGMET forecasts embedded thunderstorms, it indicates that the
thunderstorms are obscured by massive cloud layers and cannot be seen.
Terminal Aerodrome Forecast (TAF) are normally valid for a 24-hour period and are
Convective SIGMET bulletins are issued hourly at H + 55
scheduled 4 times a day 0000Z, 0600Z, 1200Z, 1800Z
Unscheduled convective SIGMETs are broadcast upon receipt and at 15
Each TAF contains: minute intervals for the first hour (H+15, H+30, H+45)

type
Obtaining a Telephone Weather Briefing
location
issuance date and time When telephoning a weather briefing facility for preflight weather information,
valid date and time pilots should:
forecast
identify themselves as pilots
state whether they intend to fly VFR or IFR
request a standard briefing to get a "complete" weather briefing
request an abbreviated briefing to supplement mass disseminated data or when
only one or two items are needed
request an outlook briefing whenever the proposed departure time is 6 or more
hours from the time of briefing

Type of Forecast

TAF : normal routine forecast

TAF AMD : amended