ASSAB Tool

Tool Steel Performance Comparison Chart

Reference Standard Hardness Chemical Composition % Austenising Range of
ASSAB
ASSAB Gr
Grad
ade
e Udde
Uddeho
holl m Gr
Grad
ade
e Characteristics Applications
AISI WNr. JIS Supplied C Si M n Cr
Cr Mo
Mo W V Others Temp. oC Hardness
COLD WORK
General purpose oil hardening tool steel with good surface hardness and Cutting :blanking,punching,shearing,trimming.
ASSAB DF-3 ARNE O1 1.2510 SKS 3 HB 190 0.95 0.3 1.1 0.5 - 0.5 0.1 - 790-850 56-62 wear resistance. Forming :bending,drawing,rim rolling,spinning,flow forming.
Gauges and measuring tools.
ASSAB XW-5 SVERKER 3 D6 (D3) (1.2436) (SKD 2) H B 2 40 2 .0 5 0 .3 0 .8 1 2.
2. 7 - 1 .1 - - 9 20 -1
-1 00 0 56
6-- 6
62
2 A 12
2%
% C r, h ig h c ar
ar b
bo
o n t oo
oo l s te
te el
el w it h e x
xcc el
el le n
ntt a br aass iv e w ea r r e
ess is ta
ta n
ncc e.
e. B la n
nk
k in gg,, p u
un
n ch
ch in gg,, c ro
ro p
pp
p in g, s h
he
e aarr in g, t ri
ri mm
mm in g a nd c li p
pp
p in g.
Good hardenability,wear resistance and excellent size stability for Blanking,punching,piercing,cropping,shearing,trimming and moulds for
ASSAB XW-10 RIGOR A2 1.2363 SKD 12 HB 215 1.0 0.3 0.6 5.3 1.1 - 0.2 - 925-970 56-62
medium runs. abrasiveplastics.

ASSAB XW-42 SVERKER 21 D2 1.2379 SKD 11 HB 210 15

. 5 0. 3 04
. 11 3
. 0. 8 - 0 .8 - 990- 108 0 58 -6 3 A 12 % C r to o
oll st ee
ee l wi th
th h igh we ar re si st an ce a nd st re ng th
th. B la nk in g, fi
fin
ne bl an
anki n
ngg, p
pu
unc hi ng, c rop pi ng, sh
she ar ing, t ri mm ing a nd c li pp in g.

CALMAX CALMAX 1.2358 HB 200 0.6 0.35 0.8 4.5 0.5 - 0.2 - 950-970 52-59 ood wear resistance and polishability. Moulds for the production of electrical components.Typical for blanking
A general steel with high toughness, ggo
dies with high demands on toughness.
HB 225 Versatile with an excellent combination of toughness and wear resistance Suitable for chipper-knives,heavy duty blanking,forming and also abrasive
VI KI
KI NG
NG V IK IN G / CH IP P
PE
ER (max)
0.5 1.0 0.5 8.0 1.5 - 0.5 - 980-1050 52-59
required for chipper-knives,heavy duty blanking and forming. plastic parts.
HB 215 Very good chipping and cracking resistance with high compressive Cold forging,forming dies,fine blanking and heavy duty blanking,thread
CALDIE CALDIE (max)
0.7 0.2 0.5 5.0 2.3 - 0.5 - 1000-1050 56-61
strength. Suitable for P VD coating to maximise wear resistance. rolling dies and coining dies. Suitable for AHSS automotive parts.
Mixed-abrasive profile,good resistance to chipping,good machining and Blanking,fine blanking,shearing,forming,coining,cold forging,cold
ASSAB 88 SLEIPNER HB 235 0.9 0.9 0.5 7.8 2.5 - 0.5 - 950-1080 58-64
WEDM properties. extrusion,thread rolling,drawing,deep drawing and powder pressing.

PLASTIC MOULD
Injection moulds and extrusion dies for thermoplastics,blow moulds,
ASSAB 618 HH (P20) 1.2738 H B 34
34 0-
0- 38
38 0 0 .3 7 0 .3 1 .4 2 .0 0 .2 - - Ni 1
1.. 0 P re
re --h
h aarr de
de n
ne
edd,, n o h ar d
de
ennii n
ngg i s ne
ne ed
ed ed
ed . P rre
e -h
-h ar
ar d
de
enne
e d pl
pl as
as titi c m ou ld s te
te el
el w itit h go
go o
od
d p o li sh
sh aab
b il itit y an
an d m
maa ch
ch in aab
b il it y.
y. forming tools,machine components,structural components and shafts.

Pre-hardened mould steel with exceptional through hardening properties, Suitable for large and very large moulds where there is high demand on
ASSAB 618 T (P20) (1.2738) H B 3 10
10 -3
-3 55
55 0 .2 6 0 .1 1 .4 5 1 .2 5 0 .6 - 0 .1 2 Ni 1 .0 5 P re
re --h
h aarr de
de n
ne
edd,, n o h aarr d
de
ennii n
ngg i s n ee
ee d
de
edd..
good polishability and etching properties combined with good machinability. surface finish.
Injection moulds and extrusion dies for thermoplastics,blow moulds,
ASSAB 718 HH IMPAX HH (P20) 1.2738 H B 3 40
40 -3
-3 80
80 0 .3 7 0 .3 1 .4 2 .0 0 .2 - - Ni 1. 0 P re
re --h
h aarr de
de n
ne
edd,, n o h
haa rrd
d en
en in g i s n ee
ee d
de
edd.. P rre
e -h
-h ar
ar d
de
enne
e d pl as
as titi c mo
mo u
ull d st ee
ee l wi th
th ve
ve rryy go
go o
od
dppo
o llii sh
sh aab
b il itit y.
y.
forming tools,machine components,structural components and shafts.
Mould for plastic injection (e.g. packaging containers,automotive interior
Pre-hardened mould steel with best toughness,good machinability and parts,reflectors,panels and handles for appliances),holder material for
NIMAX NIMAX HB 36
360-400 0.1 0.3 2.5 3.0 0.3 - - Ni 1.
1.0 Pre-hardened, n
no
ohhaardening iiss n
ne
eeded.
very good polishability. forging,diecasting dies,cutting tools,hot runner manifolds and structural
components.
Injection moulds and blow moulding for corrosive plastics. Plastic
Ni 0.6 Pre-hardened corrosion-resistant mould steel.It has very good
MIRRAX 40 MIRRAX 40 (420) HB 360-400 0.21 0.9 0.45 13.5 0.2 - 0.25
+N
Pre-hardened,no hardening is needed.
machinability,toughness
ity,toughness and polishing properties.
moulding of high surface finish parts (e.g. Bezels and casings for LED/LCD).
PET bottles and construction parts.

MIRRAX ESR MIRRAX ESR (420) HB 2

25
50 0.25 0.3 0.5 13.3 0.3 - 0.3 Ni 1.3 1000-1025 44-52 Stainless mould steel with a unique combination of toughness,corrosion For all types of moulds,especially suited for larger tools where corrosion
+N resistance and through-hardening properties. in production is unacceptable and where high surface finish is required.
Stainless plastic mould steel with excellent polishability and corrosion Injection moulds for highly polished parts and for moulding corrosive
STAVAX E
ESSR STAVAX E
ESSR (420) (1.2083) (SUS 4
42
20J2) HB 190 0.38 0.9 0.5 13.6 - - 0.3 - 1000-1050 44-52 resistance. plastics.
For general hot work and plastic moulds.Specifically used where high
Suitable for both hot work and plastic mould applications,especially large toughess and high surface requirements are needed in large plastic
VIDAR 1 ESR VIDAR 1 ESR H11 1.2343 SKD 6 HB 185 0.38 1.0 0.4 5.0 1.3 - 0.4 - 990-1010 44-52 plastic moulds that require good toughness in combination with high moulds,such as lens, extension and reflector moulds for Automotive
surface finish obtained by polishing or texturing. lightingsystems.
High hardness and very good toughness.ESR for excellent polishability. Plastic moulds for abrasive plastics.Suitable for heavy blanking,powder
UNIMAX UNIMAX HB 1
1885 0.5 0.2 0.5 5.0 2.3 - 0.5 - 1000-1025 52-58
Suitable for coating and nitriding. compacting as well as for warm forging.
S 0.12 Holders/bolsters for plastic moulds,plastic and rubber moulds with
Stainless steel for holder blocks with excellent machinability and
ROYALLOY ROYALLOY (420 F) HB 290-330 0.05 0.4 1.2 12.6 - - - +N Pre-hardened,no hardening is required.
corrosion resistance.
low requirements on polishability,dies for plastic extrusion and for
+Cu constructional parts.
Excellent polishability,good machinability
lity and good resistance to Recommended where extreme surface finishes are required,such as lens
P OLMAX POLMAX (420) (1.2083) (SUS 420J2) HB 200 0.38 0.9 0.5 13.6 - - 0.3 - 1000-1050 46-52 corrosion and wear. moulds and CD moulds.
Ni 9.2 Injection moulds for corrosive plastics,rubber,medical and food industry,
CORRAX CORRAX HRC 34 0.03 0.3 0.3 12.0 1.4 - - Al 1.6 Age har
hardeni
dening
n g to HRC 40-51
40-51 Age hardening stainless
stainless steel
steel with su
superio
perior corrosion
corrosion resistance.
istance. extrusion dies,and engineering parts.

Pre-hardened,do not have a solid solution High-strength beryllium copper mould alloy supplied at approx.40 HRC, Blow moulds : pinch offs,neck rings and handle inserts.
ASSAB MM40 HRC 40 B e 1.9 (C
(Co+Ni) 0.25 C
Cu
u Bal. and aging treatment suitable where a combination of high thermal conductivity,corrosion Injection moulds : moulds, cores and inserts.
resistance and polishablity is needed. Injection nozzles and manifolds for hot runner systems.

HOT WORK
High performance hot work tool steel with very good resistance to heat Excellent choice for die casting of aluminium and magnesium,hot stamping,
DIEVAR DIEVAR HB 160 0.35 0.2 0.5 5.0 2.3 - 0.6 - 1000-1030 44-52
checking,gross cracking,hot wear and plastic deformation. forging,and aluminium extrusion.
ASSAB 8407 ORVAR H13 Meets and exceeds NADCA 207-2011 specification for premium die Suitable for high pressure die casting,hot extrusion,press forging tools
Premium 1.2344 SKD 61 HB 180 0.39 1.0 0.4 5.2 1.4 - 0.9 - 1020-1050 44-52
castingmaterials. and moulds for plastics.
SUPREME SUPREME
Hot work tool steel with overall good ductility,toughness,wear
ASSAB 8407 2M ORVAR 2M H13 1.2344 SKD 61 HB 185 0.39 1.0 0.4 5.3 1.3 - 0.9 - 1020-1050 42-52
resistance,hardenability and machinability.
Tools for extrusion,hot forg ing and pressing and moulds for plastics.
Die casting dies and associated tooling, extrusion dies and extrusion
QRO 90 SUP
SUPREME
REME QRO
QRO 90 SU
SUPREME
PREME HB 180 0.38 0.3 0.8 2.6 2.3 - 0.9 - 1020-1050 42-52 Highest temperature strength and ver y good thermal fatigue resistance.
tooling,forging dies,esp.for copper and brass and hot stamping dies.
HB 230 Good temper resistance and higher temperature strength than H13 type
FORMVAR FORMVAR (max)
0.35 0.2 0.5 5.0 2.3 - 0.6 - 1000-1030 44-52
steel.
Tools for hot forging and extrusion.

POWDER METALLURGY
ASSAB PM 23 VANADIS 23 HB 260 Powder high speed steel with excellent wear resistance and toughness. Blanking of medium to high carbon steel,blanking of harder materials.
(M3:2) 1.3395 (SKH 53) (max) 1.28 - - 4.2 5.0 6.4 3.1 - 1050-1180 60-65 Suitable for very long runs. Moulds for very abrasive plastics and IC moulds.
SUPERCLEAN SUPERCLEAN
ASSAB PM 30 VANADIS 30 HB 300 Powder high speed steel for cutting tools with excellent wear resistance, Suitable for chip forming multi-edge cutting tools,single-edge cutting
(M3 :2 +Co) 1 .3 29
29 4 S KH
KH 40
40 (max)
1.28 - - 4.2 5.0 6.4 3.1 Co 8.5 1050-1180 60-66
toughness and good hot hardness.
tools,cold work applications with high demands on wear resistance and
SUPERCLEAN SUPERCLEAN IC moulds.
ASSAB PM 60 VANADIS 60 HB 340 Powder high speed steel for cutting tools with excellent wear resistance, Suitable for chip forming multi-edge cutting tools,single-edge cutting tools
(1.3292) (max) 2.3 - - 4.2 7.0 6.5 6..5 Co 10.5 1100-1180 60-68 toughness and excellent hot hardness. and cold work applications with high demands on wear resistance.
SUPERCLEAN SUPERCLEAN
VANADIS 4 EXTRA VANADIS 4 EXTRA HB 230 1.4 0.4 0.4 4.7 3.5 - 3.7 - 950-1150 58-64 Powder tool steel for long run tooling,where high demands on adhesive Blanking,fine blanking,forming of thicker work material, esp.austenitic
SUPERCLEAN SUPERCLEAN wear and chipping resistance is required. stainless steel.mild carbon steel, AHSS, copper and aluminium.

VANADIS 8 VANADIS 8 HB 2
2770 2.3 0.4 0.4 4.8 3.6 - 8.0 - 1020-1080 58-64 Powder tool steel for very long run tooling ,where abrasive wear
resistance and good toughness is required.
Blanking,forming,fine blanking,deep drawing,cold forging and powder
compacting,
SUPERCLEAN SUPERCLEAN
VANCRON 40 VANCRON 40 HB 30
300 1.1 0.5 0.4 4.5 3.2 3.7 8.5 N 1.
1.8 950-1150 58-65
A nitrided powder tool steel for the very best resistance to galling and Blanking,fine blanking,deep drawing,bending powder compacting of soft
SUPERCLEAN SUPERCLEAN adhesive wear.Normally no coating is necessary. and adhesive metals.
ELMAX ELMAX HB 280 1.7 0.8 0.3 18.0 1.0 - 3.0 - 1050-1100 56-60 Powder tool steel and stainless plastic mould steel with high wear and Electronics industry:connectors,plugs,switches,resistors and integrated
SUPERCLEAN SUPERCLEAN corrosionresistance. circuits.
( ) - modified grade

www.assab.com This information is based on our present state of knowledge and is intended to provide general notes on our products and their uses. It should not therefore be construed as a warranty of specific properties of the products described or a warranty for fit ness for a particular purpose. Edition 160921