Peper cet tt SOPHIA SPLIT AIR CONDITIONER WITH HEAT PUMP TROUBLESHOOTING1.1 Indoor Unit Error Display “PS Ongraton | Timer lamp | Display | LED STATUS ‘time x £0 _ | Indoor unit EEPROM parameter error 2 times x 1 _ | Indoor / outdoor units communication error 3 times x £2 _ | Zero-crossing signal detection error * 4 times x £3 _ | Indoor fan speed has been out of control Tndoor room temperature sensor T1 open Grcurt or Stimes x £4 | shor circuit Evaporator coil temperature Sensor T2 open arcu or S times x ES | shor circuit 7 times x EC _ | Refrigerant leakage detection 1 times ° FO | Overload current protection Dimes 3S F1__| Ouldoor ambient temperature sensor T# open circuit or short circuit Condenser coil temperature sensor T3 open circuit or 3times ° F2 | shortcircuit Compressor discharge temperature sensor TP open % 4 times ° F3 | circuit or short circuit 5 times ° F4 _ | Outdoor unit EEPROM parameter error 6 times ° F5__ | Outdoor fan speed has been out of control 1 times Se PO | IPM malfunction or IGBT over-strong current protection 2 times : P1__ | Over voltage or over low voltage protection : High temperature protection of IPM module or S times P2 | compressor top 4 times Se P3* | Outdoor ambient temperature too low. Stimes P4 _ | Inverter compressor drive error 6 times P5 | Indoor units mode conflict (multizone ONLY) Times 7 P8__| Low pressure protection (Only for 36K) Oight) —_X coff) se flash) 1) In heating mode, when the outdoor temperature is lower than -25C for 1 hour, the indoor unit display error code P3. 2) If the outdoor temperature is higher than -22°C for 10 minutes and compressor stop for 1 hour or ‘outdoor temperature is higher than -5°C for 10 minutes, then the unit will return to work. * Fault Symptom: The display board shows a garbled code or a code that is not an error code found in the service manual nor a temperature reading, Trouble shooting: Use the remote controller. If the unit does nat respond to the remote, the indoor PCB needs to be replaced; if the unit does respond, then the display board needs to be replaced1.2 Outdoor unit error display(TBD) For CH-09SPH-115VO, CH-12SPH-115VO, CH-09SPH-230VO, CH-12SPH-230VO,For CH-09SPH-230V0, CH-12SPH-230V0, CH-18SPH-230VO, _ CH-18SPH-230VOFor CH-24SPH-230V0,After power on, LED3(Green color) and LED2(Red color) will be flash if the unit has some problems. Leos lLeD2 INo. [Problems (Green) Rea) [U display Ht Jstandby for normal lo x 2 |Operation normally k lo |IPM maifunction or IGBT over-strong current protection Ix IPO I lover voltage or too low voltage protection lo lo P1 EEPROM parameter error lo IES be linverter compressor drive error k i Pa linverter compressor drive error 3 lo Pa |inverter compressor drive error x fe Pa O dight)—X (off)For CH-S30F TXW-SV, CH-S36FTXW-SV,IPM board,1.3 Diagnosis and Solution 1.3.1 EEPROM parameter error diagnosis and solution(E0/F4) Error Code E0IF4 Malfunction deci: condi Indoor or outdoor PCB main chip does not receive feedback from EEPROM chip. Installation mistake © PCB faulty ‘Supposed causes Trouble shooting Power off, then restart the unit 2 minutes later. Yes Replace the indoor/outdoor main PCB. EEPROM: a read-only memory whose contents can be erased and reprogrammed using a pulsed voltage. For the location of EEPROM chip, please refer to the below photos.1.3.2 Indoor / outdoor unit's communication diagnosis and solution(E1) Error Code 3] Malfunction de indoor unit does not receive the feedback from outdoor unit conditions during 110 seconds and this condition happens four times continuously. ‘Supposed causes Wiring mistake © Indoor or outdoor PCB faulty Trouble shooting: Power off, then restart the unit 2 minutes later Is the error extinguished? | No ¥ Measure Vs. Is the voltage moving alternately between -25V to 25V? — 1 Yes ¥ Check the outdoor wiring connection. , Ie the wiring comecty Check the indoor wiring connection. Is the wiring correctly? Yes ‘ \ Yes Replace the reactor <-No—< Check whether reactor { ig normal? Replace the indoor main PCB. Power on. Is the error 1 extinguished? Yes | ¥ No Replace the outdoor main PCB. + Power on. Is the error Replace the outdoor main PCB. extinguished? i No Replace the indoor main PCIRemark: Use a multimeter to test the DC voltage between 2 port and 3 port of outdoor Unit. The red pin of multimeter connects with 2 port while the black pin is for 3 port. When AC is normal running, the voltage will move altenately between -25V to 25. If the outdoor unit has matfunetion, the voltage will move alternately with positive value. While if the indoor unit has malfunction, the voltage will be a certain value. Remark: Use a multimeter to test the resistance of the reactor which does not connect with capacitor. The normal value should be around zero ohm, Otherwise, the reactor must have maifunetion.1.3.3 Zero crossing detection error diagnosis and solution (E2) Error Code E2 Malfunction de 9 conditions minutes or the zero crossing signal time interval is abnormal. ‘Supposed causes © Connection mistake © PCB faulty Trouble shooting: /, Check if the connections and, < No___».Cortect the connections. Tum on the power supply is normal? —_/ Unit when the power supply is good \ Yes ¥ Indoor main PCB is, defective. Replace indoor main PCB.1.3.4 Fan speed has been out of control diagnosis and solution(E3) Error Code ESIFS Malfunction de When indoor fan speed keeps too low (300RPM) for certain time, conditions the unit will stop and the LED will display the failure. ‘Supposed causes © Wiring mistake © Fanass'y faulty Fan motor faulty © PCB faulty Trouble shooting: Power off, then restart the \ Unit 2 minutes later ——_/ No———» The unit operates normally Yes y / Shut off the power supply, No » Find out the cause and have Rotate the fan byhand. it solved Yes , << Check the wiring of fan No- >» Correct the connections. \ motor Yes ‘Measure the Voltage for the \ fan motor from the main PCB refer to the ‘Appendoc 1 No» Replace the main PCB ¥ Yes ¥ Replace the fan motor NoIndex 1: ‘:Indoor or Outdoor DC Fan Motor(control chip is in fan motor) Power on and when the unit is in standby, measure the voltage of pin‘-pin3, pin4-pin3 in fan motor connector. If the value of the voltage is not in the range showing in below table, the PCB must has problems and need to be replaced, [LES| 1 345 6 Red Black White Yellow Blue DC motor voltage input and output(voltage: 220-240V~) NO. | Color | Signal Voltage 1 Red_| Vs/Vm 280V-380V 2 a a = 3__| Black | GND ov 4__| White [vee 14-17 V 5__| Yellow | _Vep 0-5.6V 6 | Blue | FG 14-17 5V DC motor voltage input and output(voltage :115V~) NO. | Color | Signal Voltage 1_[ Red | Vsivm 140V~190V. 2 = f= = 3_| Black | GND ov. 4 | White [Voc 14-17 5V 5 | Yellow | Vsp 0-5.6V 6 | Bue | FG 14-17.5V 2, Outdoor DC Fan Motor (control chip is in outdoor PCB) Power on ,and check if the fan can run normally, if the fan can run normally, the PCB must has problems and need to be replaced, If the fan can't run normally, measure the resistance of each two pins. If the resistance is not equal to each other, the fan motor must have problems and need to be replaced, otherwise the PCB must has problems and need to be replaced. 3. Indoor AC Fan Motor Power on and set the unit running in fan mode at high fan speed. After running for 15 seconds, measure the voltage of pin’ and pin2. If the value of the voltage is less than 100V(208~240V power supply}or 50V(115V power supply), the PCB must has problems and need to be replaced.1.3.5 Open circuit or short circuit of temperature sensor diagnosis and solution(E5) Error Code E/ESIF1/F2/F3 Malfunction decision __| If the sampling voltage is lower than 0.06V or higher than 4.94V, conditions the LED will display the failure. ‘Supposed causes ‘© Wiring mistake © Sensor faulty «PCB faulty Trouble shooting: Check the connection between temperature ———No——®! Correct the connection ‘sensor and PCB, ' Measure the resistance value of the sensor Yes + Replace indoor or outdoor main PCB ——No—>__Repalce the sensor1.3.6 Refrigerant Leakage Detection diagnosis and solution(EC) Error Code EC Malfunction decision _| Define the evaporator coil temp.T2 of the compressor just starts conditions running as Tcool. In the beginning 5 minutes after the compressor starts up, if T2 ‘Stop the unit. Check the power supply > No Clear tha blockage No ¥ / / Check the compressor resistance values refer to the [Compressor checking]. 's it normal? Yes Z Check the connections and «wires is tel conection? Vaames is tei vonneswon? _/ Yes ¥ \ Check the reactor .Is it normal? ‘So —+ / Replace the compressor / \__nonmal?_ Correct the connections or replace the wires, >No >| Replace the reactor Yes ¥ Replace the outdoor main PCB1.3.7 IPM malfunction or IGBT over-strong current protection diagnosis and solution(P0) Error Code PO Malfunction decision conditions When the voltage signal that IPM send to compressor drive chip is abnormal, the display LED will show “PO” and AC will turn off. ‘Supposed causes © Wiring mistake IPM malfunction © Outdoor fan ass'y faulty © Compressor malfunction © Outdoor PCB faulty Trouble shooting: For 9K~24K: / Check ifthe wiring between main. \ a Correct the connection or replace PCB and compressor. If the wires Yes and connectors are broken? / {he wires and connectors, No y IPM continuity check. Check if the (IPM terminal resistance values aro) \ uniform. / Yes ¥ . / Check if the outdoor fan runs. properly or the outdoor unit ventilation is good. Yos Z Check if the compressor resistance \ values are uniform Yes a Replace the outdoor main PCB if the main PCB and IPM are separate, 7 Replace the IPM board or replace the No main PCB if the IPM board and main PCB are integrated together. » Please refer to the solution of [Fan Speed Has Been No Out Of Control] malfunction Replace the compressor. tooFor example:For 30K~36K: Al first test the resistance between every two ports of U, V, W of IPM and P, N. If any result of them is 0 or close to 0, the IPM is defective, Otherwise, please follow Commas bent \__ eer nt (sr pe omar ato on Rech bag oF Sw Sees ) the procedure below: acct Saar an / ometetier the comecing\ (cairn Ol ea seeenccorearreney/ 4 seats aa, CERES serene seen | (gen) as a ‘epceiP ones Rice PFC moat ha) eng aaerse1.3.8 Over voltage or too low voltage protection diagnosis and solution(P1) Error Code P41 Malfunction decision _| An abnormal voltage rise or drop is detected by checking the conditions specified voltage detection circuit. ‘Supposed causes Power supply problems. System leakage or block PCB faulty Trouble shooting: © cock the power supply No——» ‘Stop the unit Yes y / Check the connections and \ wires Correct the connections or No replace the wires. Yes ¥ CZ, Check the volage between P , and N No- Replace the IPM board Yes a (Check the reactor No: | Replace outdoor main PCB Yes y Roplace the reactor1.3.9 High temperature protection of IPM module or compressor top diagnosis and solution(P2) Error Code P2 Malfunction decision __ | If the sampling voltage is not SV, the LED will display the failure. conditions ‘Supposed causes Installation mistake Power supply problems. ‘¢ System leakage or block + PCB faulty Trouble shooting: For 18K,24K, Check if the Fastening screws \ on the PCB and IPM radiator.) are fixed tightly. / No Tighten the screws and apply silicon grease, Replace the outdoor control PCB. For other models, / Speck We a NW YS gg Clear up the arinlet and cute rte neat So Soames? ichanger of ngoorandoutcoor uns No + Tum off the power supply and turn iton 10 minutes later. Yas /- Check ifthe terperature / heck ial the connection, especially \ Jee Temperate \ No —x{ “the connection of OLP (Over Load” No», Core he cannes, / —_, Yes Yes /WMeasue the resistance \ / Cree in rakigarant between the two ports of )—No—», Replace the OLP. < system / > \ the OLP. Is itzero? \ is normal? / No Yes Yes - lace the outdoor control PCB, Replace the outdoor control PCB. ae a4.3.10 Inverter compressor drive error diagnosis and solution(P4) Error Code P4 Malfunction decision __| An abnormal inverter compressor drive is detected by a special condi detection voltage detection, compressor rotation speed signal detection and soon. ‘Supposed causes © Wiring mistake IPM malfunction Outdoor fan ass’y faulty Compressor malfunction Outdoor PCB faulty ‘Trouble shootin: For 9K~24K: /, Check ifthe wiring between main \ Correct the connection or {PCB and compressor connected No] replace the wires and \\ well? / connectors. Yes — Z Check the reactor or Inductance Is it normal? Replace the reactor or No] Inductance Cored he sation ___ . << Check fine PM instal corecty, >——_No——|_"ighten te sere ane ‘apply slicon grease, Yes Yes IPM continuity check. Check the IPM terminal resistance values are Replace the IPM board or replace ¢ No—|the main PCB ifthe IPM board andl \ uniform, main PCB are integrated together. Yes / Check f the outdoor fan rans, Pease refer to the solution of [Fan] (property or the outdoor unit )—No—} Speed Has Been Out Of Control] \ Ventilation fs good. / ‘malfunction Yes / ____. Z. Cheskif the compressor resistance < values are uniform D—Ne—__ Replace the compressor. Yes rT Z, Replace the outdoor main PCB ifthe, < main PCB and IPM are separate, 7 IPM continuity check ‘Tum off the power, let the large capacity electrolytic capacitors discharge completely, and dismount the IPM. Use a Cigital tester to measure the resistance between P and UVWN; UVW and N.Digital tester Normal resistance value Normal resistance value Red Black N ° es Pp U Vv (Several Ma) (Several MA) Ww For 30K~36K: At first test the resistance between every two ports of U, V, W of IPM and P, N. If any result of them is 0 or close to 0, the IPM is defective. Otherwise, please follow the procedure below: _/ cose onaacna pve vorane esne ant anin ue sy Toa L ponema - a = \ a (vase one sac wera, BE eae ‘coos ona > (eu > : / \ J Daten sass coro ey a4 =a J ‘bets > ence neater man PR x — roma ~Y cosccunener ne renee sem SS -ro-o{ Me ne ear nt ean et 1» hs ten af ona matuncian ) toNtetarcorany >>) Resomest wat geet Recomect ek ve : nono secon > [ese sation fsa] eo neice scores: / Fase a FF meds) toe ge, Seca ae et ee en ee maar4.3.11 Low pressure protection diagnosis and solution(P6) Error Code P6 Malfunction decision conditions When th pressure protector will 5 je pressure of system reach a certain value, the low h off. After the pressure resume to normal ,the protection code will ‘Supposed causes Wiring mistake Pressure protector faulty © Fan motor faulty PCB faulty «System problems. ‘Trouble shooting: Tener me wang teeen elo pessue protector anamancontt —Ne-s| inn wa coecty T + pressure protector ‘sbroven aod Deanne pug. Measure the \Bisance the ow pressure protector. fine protectors normal he vate ve + ‘check wnener te outdoor ambient lemperaiure soo T No ——+ check wnetne vane cor ot gh pressure vanes pene ve Check te incor fan uns sropety in eboang mode \ ve Replace oxtoor man pars No ‘eTgerant ent eng 20a retigerane No ceigran system ok | —No->{_ Replace ow pressure pater rer! ‘Spine unt \—No-»| OPen uly vate ce ofrgn N ‘pessure va sla eae en on No) matncton) Fd oli cause nd hve sobaMain parts check 4, Temperature sensor checking Disconnect the temperature sensor from PCB, measure the resistance value with a tester. ooo [| 8 Tester ‘Temperature sensors. Roam temp (T1) sensor, Indoor coil temp.(T2) sensor, Outdoor coil temp.(T3) sensor, (Outéoor ambient temp,(T4) sensor, ‘Compressor discharge temp (TP) sensor. Measure the resistance value of each winding by using the multl-meter.Appendix 1 Temperature Sensor Resistance Value Table for 1,12,73,T4 (°C-K) °c [°F [ Konm | “c [ F [ KOnm | °C | F [ KOnhm | c [ * [ KOhm 20 | 4 | 116266 [ 20 | 08 | 126431 | 60 | 140 [ 25774 | 100 | 212 | o.2e7s 9 | 2 | toas4s [ 21 | 70 | 120561 | o1 | 142 | 227289 | 101 | 214 | otis =e [0 | tore | 22 | 72 as | o2 [144 | 2i9073 | 102 [216 | 050080 =7_|_1 | s6sa23 | 23 | 7s | toars1 | 03 | 145 | 211241 | 103 | 217 | osress =e | 3 | aesees [ 2¢ | 75 | 104736 | 64 | 147 [ 203752 | 104 | 219 | o.ss0se =5 |_s | es20 | 25 | 77 10 es | 148 | 1905e2 [105 [221 [ osaess =4 | 7 [| 79311 [ 26 | 79 [| sssore | 66 | 151 [ 189627 | 106 | 225 | osa012 3 | 2 | 7asso | 27 | 81 | 912445 | o7 | 153 [ 183003 | to7 | 225 | ostazs ~2 | 10 [| 7016s | 28 [ 82 | aries | 68 | 164 | 176647 [ 108 | 226 | 0.49089 = | 12 | ceosss | 20 | 84 | ssss05 | co | 150 | 170847 | 109 | 228 | 0406 10 | 14 | 622756 [ 30 | a6 | 7a7ore | 70 | 158 | 164601 | 110 | 230 | 0.47256 9 [16 | saro7e | 21 | a8 | rear | 7 | 160 | 150008 | 111 | 232 | o.s07 8 [| 18 | s63004 | 32 | 90 | 720904 | 72 | 102 | 150008 | 112 | 234 | 0.44099 7 [19 | s22a3e [23 [91 | eeeraa [73 | tea | saecer [113 [235 [o4aaa2 3 [ 21 | 49361 | 34 | 93 | o0ss55 | 74 | 105 | tases | 114 | 237 | o.4as04 5 _[ 23 | 465726 | 26 | 05 | s4o021 | 75 | 67 | 138703 | 115 | 230 | o4ties 4 [2 44 36 | a7 | sts0s0 | 76 | 169 | sats | 116 | 241 | 0.006 ~3_|_27 | a1sere | a7 [98 | se7sso [77 | 171 | t2007e | 117 | 243 [ 0.08007 2 | 28 | 9829 | se | 100 | sezom | 7a | 172 | 125405 | 118 | 248 | osrose =1_[ 30 | a7.1088 | 30 | 102 | sa00a0 [70 | 17a [ 12103 [119 | 246 [ o.s0054 o | s2 | ss.20e | 40 | 104 | savso | 20 | 176 | 117303 | 120 | 248 | o.ssa82 + _| 34 | sssz6s [41 | 106 [496302 [a1 | 178 [ 119604 [ 121 | 250 | 0.95042 2 | 36 | stsess | 42 | 108 | 47e253 | 22 | 120 | 1.00080 | 122 | 252 | oats 3 | s7 | 280058 | 43 [ 108 | 45705 [ 63 | ter | 106e4a | 123 | 253 | 0.39246 4 | 38 | 2esac0 | a4 | 111 | asarse | 04 | tes | 1.03000 | 124 | 255 | 0.3209 5 | a | 26ers | 45 [ 113 | 421263 [ 65 | 105 | oooe1s | 126 | 257 | 0.91659 6 | 43 | 2545 | 46 | 115 | 40a5e0 | 26 | ter | oo0ce: | 126 | 259 | o.s0754 7 [ 45 | 241902 | 47 [ 117 | 300673 [ a7 | 109 | o9se62 | 127 | 261 | 0.20074 3 | 46 | 225002 | 48 | tte | azaaze | a8 | 190 | o907sa | 128 | 262 | 020016 9 | 48 | 21804 | 49 [ 120 | 3.80962 [ 69 | 192 | cers | 129 | 264 | 0.26482 70 [| 50 | 207164 | so | 122 | 345007 | 00 | 104 | 085248 | 100 | 266 | o2777 11 [ 52 [| ts0e01 [ 51 | 124 [ steer | 91 | 196 | o.s2cas | 131 [ 208 | 027078 12 | 84 | te7i77 | 62 | 126 | aaotes | o2 | 198 | oor | 192 | 270 | 2608 13 | 55 [| 17.8005 [ 53 | 127 | sorors | 93 | 199 | orrros | 135 [ 271 | o2s7s7 14 _[ s7 | te0s41 | 64 | 120 [| 205006 [ o¢ | 201 | ovears | 134 | 273 | 026126 75 | 59 | terse | 55 | 131 | 2esaa1 | os | 203 | ovsita | 135 | 275 | o2asi2 7e [1 | waste | 66 | 133 | 279023 | 86 | 205 | o7ooa | 136 | 277 | o2s016 a7 | es | ter | s7 | 138 | 20882 | o7 | 207 | ossaaa | 137 | 279 | o2sase 73 | 64 | ise | 58 | 136 | asses | 98 | 208 | oseate | 138 | 200 | 022776 79 | 65 | 132001 | se | 138 | 2aaor7 | 09 | 210 | osaeca | 199 | 282 | 022237Appendix 2 Temperature Sensor Resistance Value Table for TP (°C ~K) °c [°F [KOhm | C | F [KOnm | °C | F [KOhm | °C | F [KOhm 20 [4 [siz 20 [6s | 6866 60 | 140 | 1369 100 | 212 _| 8.702 19 [2 [sie 2i__[70 | e562 e [2 [tan tot 2t4 | ss95 18 fo | 483 22 [72 | 6273 62 [144 | 1265 102 [216 | 9.492 a7_[a__ [4558 23__[73__| 5298 63 [14s [221 103 [ai7_| 3.302 16 [3 [4305 24 [75 [5737 64 | 1a7_| 1179 104 [219 | 9.296 15 [5 | 4067 25 _[77__| 5489 65 [149 _| 1138 105 [221 | 3.203 a4 [7 [3843 26 [79 | 5253 06 | 151 _| 10.99 706 | 223 | 3.113 =13 [oe _| 963.8 27__[er_| 6028 e7_| 163_[ 1061 sor [225 [3.025 12 [10 | 3436 28 [82 | 4a4 8_| 154 _| 1025 108_| 226 [2941 a1 [12 _[ 926 28 [es [4ett 69 | 166 | 9.902 sos [226 | 2.86 =10_[ 74 | sor7 30 [se | aair 70__| 168 _| 9.569 110_[ 280 [2781 3 [6 [213 si [ss [4239 7 [160 [9.298 a1t_| 232 [2.704 3 [78 | 2758 32__[s0 | 4057 72__| 162 |as4 v12_| 284 | 208 7 [19 [2614 33 [ot | 9889 73 [163 | 6643 113_| 295 | 2.569 3 [2i_|2are a [es [ara 74__|165_| 6.368 114_|2a7_| 2409 5 [23 | 2348 35 [95 | 95.78 75__| 167 _| 6.084 115_| 209 | 2.422 4 [2s [2228 36 [er__| aaa 76 | 169_| 7.82 116 [2a _| 2.387 3 [a7 [ana 3a7__ [99 [3294 7__[am_| 7.566 117_[ 243 | 2.294 2 [28 | 2007 36 [ 100 | e162 7 | 172_| 7.321 11e_[2ss_| 2.298 [30 __| 1908 3a [102_| sas6 79_| 174 _| 7.086 119 [246 [2174 0 _[sz_| 1808 40 [104 [29.15 80 _[ 176 | 6.869 720 | 248 | 2.tt7 1_|[s4_[arie a [10s [28 e_[ ave [eos 721_| 260 | 2.067 2 [36 | 1633 42 [108 [269 a2 [180 [643 122_| 262 _| 2.007 3__|ar_| 1552 43 [109 _| 2586 33__|ta1_| 6228 123_| 253 _| 7.955 4 [ss [76 44 [att _[ 2485 84 [169 _| 6.033 124_| 265 _| 1.905 5 [4t_| 1404 45 __[113_| 2380 35 | 195 _| 8.844 128_| 267 _| 1.856 6 [43 | 1335 4 [115 [2289 36 | 167 _| 5.663 126 | 250 | 1.808 7 [4s_|a2ra a7_[a_[2at e7__| 100 _| 6.488 12r_[261_| 1.762 Es Ee 48 [118 [2126 38 [190 | 532 128 | 262 | 1.717 2 [4e__| 1582 48 [120 [2046 39 | 192_| 6.167 128268 | 1.674 10 [so | 1098 60 | 122 _| 1968 a [i [5 730 | 266 | 1.682 11 __[62_| 1046 1 [124_| 1896 a _[ 196 | 4649 12 [54 __| 9969 32 [126 _| 1826 92 [198 | 4703 13_[85 | 95.05 63 [1a7_| 1758 93 [199 | 4.562 14__[a7__| 9086 34 [129 | 1694 24 | 201_| 4.426 15 [59 | 86.49 55 | 131_| 1632 95 | 203 | 4.204 16 [er__| e254 56 | 193_| 18:73 96 | 205 | 4.167 7 [63 __| 78.79 o7__[135_| 15.16 o7__| 207_| 4.045 18 [es __| 75.24 68 | 196_| 1462 98 | 208 | 9.027 io [es _| 71.88 so [138_| 1409 99 [210 | saiAppendix 3: 9AT(°C) ATC) = —=— SEE 3] 266 | 2 | rae | a3] tara | ea | 1002 | 15 | 200 2 | 2a || 152 | e+ | 1202 | es | 1058 | 116 | 2108 a} -s02 [96 7 | a5] 11 | 20 | se08 | 117 | az os | 58 [a9] 8) ae or 885 | 8 280 os) 320] 958) 788) sr) 146 | e8 | s008 10) a6 < [ose | a] a8) a8) sos | ae 922] 120) is | 347 | a | soa | 50 | 1952 | oo | 198 | 11) os as| 00 | 92 | eo8 | es | tesa] ea | 2012] 15 | 267 [302 | 3 [ora] 0s | wr | 08 | 20 | 128 | 2800 ae] 401 [4 | s82 | e5 | 149] se | aos 1107-008 Spat as) 65) sass | er aon) 2828 ¢ | ae) 38 | 58) er) ase | ee |g) 120) 2082 7] aae | sr] 936) es) tse] 092102) 150) 2088 a | ste] at] aose | 72 | to16 | 103 aire | 13 | ara 12 | sxe | a2 | wre | 73 | 100.4 | 108 | a102 | 105 | 276 191 ~ssa [43 | 1008 | 78 | 1652 | 105 [201 | 1961-208 [sre |e me | 25 | 107 | 108 [zee | 157 | or 15] 58 | 45 [ 113 | 76 | 4088 107 | 2048 | 156 | 2004 “60 | a8) 88) 77) 706 | 103064) 159) 2802 a7] 26 | 7 | 05 | 78 | a7a4 | 100 | 2202 | 140288Appendix 4 1. Normal voltage of P and N 1208-240V( i-phase, S-phase) | 360-420V/3-phase) In standby ‘around S10VDC_ [__2tound 630VDC_ in operation With partir With passive Mahe pee | With fly active ) PFC module ae PFC module >200VDC 3310VDC. S37OVDC. 3450V002. Compressor checking Measure the resistance value of each winding by using the tester Input Terminal / Blue ¢ \ Blue [1 3 Red 9 { a A Black 3 }——\ Y Red Position Resistance Value ASNOBOZZUFZ_| ASMTSED23UFZ | ATF23GD22UMT | ATF2S0D22UNT Bue Red weed 175.0 0750 Blue Black tera ose Red Blue3. Fan Motor Measure the resistance value of each winding by using the tester, Modal YETSE8 | YKTS26- YaTaBS- YET-SS-6- 202. 3L 208 200L Brand "Tongde Wweling welling welling Back 36 23 782 eas Red Main ‘Be = oa 188 a2 138 Black BUX4, Pressure On Service Port Gooting chart: °F(°C) ODT 75 85 95 105 115, oT (23.89) | (20.44) (35) (40.56) (46.11) BAR 70/59 8.2 78 84 8.6 10.1 BAR 75/63 8.6 8.3 87 9.1 10.7 BAR. 80/67 9.3 89 O41 96 W.2 RC ODT 75 85 95 105 115, FCC) | pt (23.89) (29.44) (35) (40.56) (48.11) PSI 70/59 119 413 447 125 147, PSI 75/63 424 120 126 132 155 Psi 80/67 135; 128 132 140) 162 omy —~_ODT 75 85 95 105 115 FCC) | pt (23.89) (29.44) (35) (40.56) (48.11) MPA 70/59 0.82 0.78 0.81 0.86 1.01 MPA 75/63 0.86 0.83 0.87 0.91 4.07 MPA 80/67 0.93 0.89 0.91 0.96 442 120 100 80 70/59 60 75/63 te 80/67 40 20 oo : : : 75 (23.89) 85 (29.48) 95 (35) 105 (4056) 115. (46.11)Heating Chart: F —~_ODT 57/53 47143 37/33 27123 1713 eo) | DT ~~} (13.89/11.67) | _(8.33/6.11) | (2,780.56) | (-2.78)-5) | (-8.33/-10.56) BAR 3 30.3 285 25.3 228 208 BAR 5 32.5 30.0 26.6 25.4 23.3 BAR 75. 33.8 35 278 26.3 24.9 °F ODT 57/53 47143 37/33 27/23 (- 17/13 (ce) _| oT ~~] (13.89/11.67) | _(8.33/6.11) | (2.78/0.56) | _2.78/-5) | (-8.33/-10.56) PSI 3 439 413 367 330 302 PSI 5 471 435 386 368 339) PSI 75 489 457 403) 381 362 °F oor 57/53 47143 37/33 27/23 (- 17/13 ce) [oT (13.89/11.67) | (8.33/6.11) | (2.78/0.56) | _2.78/-5) | (-8.33/-10.56) MPA 3 3.03 2.85 2.53 2.28 2.08 MPA 5 3.25 3.00 2.66 2.54 2.33 MPA 75. 3.38 3.15 2.78 2.63 2.49 40,0 350 + 300 | 20 + 200 + 55 150 4 es 75 100 + 50 oo | 57/53 47/03 37/33 27/23 aa (13.89/11.67) (8.33/6.11) —(2.78/0.56)—(-2.78/-5)__(-8.33/-10.56) 2. Disassembly Instructions Note: This part is for reference, the photos may have slight difference with your machine. 2.4 Indoor unit No. [Parts name _| Procedures [RemarksFront panel How to remove the front panel 1) Pull the below side of the panel toward you and remove screw of the cover. 2) Release the connector of the display ass'y. 3) Release the two clips and then remove the panel. 4) Remove the filter and the horizontal louver. 5) Remove the three screws and then remave the panel assy.Electrical parts How to remove the electrical parts. 1) Remove the front panel from procedure 1 2) Pull out the room temp. sensor (T1). Remove the two screws for the ground connection. 3) Remove the fixing screw. 4) Pull out the coil temp. sensor. 5) From the side direction, open the electronic control box cover fixing by clips. Pull out the fan motor connector and ‘swing motor connector. Then remove the electronic control box.