LM35 Precision Centigrade Temperature Sensors

November 2000

LM35
Precision Centigrade Temperature Sensors
General Description aged in hermetic TO-46 transistor packages, while the
LM35C, LM35CA, and LM35D are also available in the
The LM35 series are precision integrated-circuit temperature plastic TO-92 transistor package. The LM35D is also avail-
sensors, whose output voltage is linearly proportional to the able in an 8-lead surface mount small outline package and a
Celsius (Centigrade) temperature. The LM35 thus has an plastic TO-220 package.
advantage over linear temperature sensors calibrated in
˚ Kelvin, as the user is not required to subtract a large
constant voltage from its output to obtain convenient Centi- Features
grade scaling. The LM35 does not require any external n Calibrated directly in ˚ Celsius (Centigrade)
calibration or trimming to provide typical accuracies of ± 1⁄4˚C n Linear + 10.0 mV/˚C scale factor
at room temperature and ± 3⁄4˚C over a full −55 to +150˚C n 0.5˚C accuracy guaranteeable (at +25˚C)
temperature range. Low cost is assured by trimming and n Rated for full −55˚ to +150˚C range
calibration at the wafer level. The LM35’s low output imped- n Suitable for remote applications
ance, linear output, and precise inherent calibration make n Low cost due to wafer-level trimming
interfacing to readout or control circuitry especially easy. It
n Operates from 4 to 30 volts
can be used with single power supplies, or with plus and
minus supplies. As it draws only 60 µA from its supply, it has n Less than 60 µA current drain
very low self-heating, less than 0.1˚C in still air. The LM35 is n Low self-heating, 0.08˚C in still air
rated to operate over a −55˚ to +150˚C temperature range, n Nonlinearity only ± 1⁄4˚C typical
while the LM35C is rated for a −40˚ to +110˚C range (−10˚ n Low impedance output, 0.1 Ω for 1 mA load
with improved accuracy). The LM35 series is available pack-

Typical Applications

DS005516-4

DS005516-3 Choose R1 = −VS/50 µA

FIGURE 1. Basic Centigrade Temperature Sensor V OUT =+1,500 mV at +150˚C
= +250 mV at +25˚C
(+2˚C to +150˚C)
= −550 mV at −55˚C
FIGURE 2. Full-Range Centigrade Temperature Sensor

© 2000 National Semiconductor Corporation DS005516 www.national.com

LM35
Connection Diagrams

TO-46 SO-8
Metal Can Package* Small Outline Molded Package

DS005516-1 DS005516-21

*Case is connected to negative pin (GND) N.C. = No Connection

Order Number LM35H, LM35AH, LM35CH, LM35CAH or Top View
LM35DH Order Number LM35DM
See NS Package Number H03H See NS Package Number M08A

TO-92 TO-220
Plastic Package Plastic Package*

DS005516-2

Order Number LM35CZ,

LM35CAZ or LM35DZ
See NS Package Number Z03A

DS005516-24

*Tab is connected to the negative pin (GND).

Note: The LM35DT pinout is different than the discontinued LM35DP.
Order Number LM35DT
See NS Package Number TA03F

www.national.com 2
 LM35
Absolute Maximum Ratings (Note 10) TO-92 and TO-220 Package,
(Soldering, 10 seconds) 260˚C
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/ SO Package (Note 12)
Distributors for availability and specifications. Vapor Phase (60 seconds) 215˚C
Infrared (15 seconds) 220˚C
Supply Voltage +35V to −0.2V
ESD Susceptibility (Note 11) 2500V
Output Voltage +6V to −1.0V
Specified Operating Temperature Range: TMIN to T MAX
Output Current 10 mA (Note 2)
Storage Temp.; LM35, LM35A −55˚C to +150˚C
TO-46 Package, −60˚C to +180˚C LM35C, LM35CA −40˚C to +110˚C
TO-92 Package, −60˚C to +150˚C LM35D 0˚C to +100˚C
SO-8 Package, −65˚C to +150˚C
TO-220 Package, −65˚C to +150˚C
Lead Temp.:
TO-46 Package,
(Soldering, 10 seconds) 300˚C

Electrical Characteristics
(Notes 1, 6)
LM35A LM35CA
Parameter Conditions Tested Design Tested Design Units
Typical Limit Limit Typical Limit Limit (Max.)
(Note 4) (Note 5) (Note 4) (Note 5)
Accuracy T A =+25˚C ± 0.2 ± 0.5 ± 0.2 ± 0.5 ˚C
(Note 7) T A =−10˚C ± 0.3 ± 0.3 ± 1.0 ˚C
T A =TMAX ± 0.4 ± 1.0 ± 0.4 ± 1.0 ˚C
T A =TMIN ± 0.4 ± 1.0 ± 0.4 ± 1.5 ˚C
Nonlinearity T MIN≤TA≤TMAX ± 0.18 ± 0.35 ± 0.15 ± 0.3 ˚C
(Note 8)
Sensor Gain T MIN≤TA≤TMAX +10.0 +9.9, +10.0 +9.9, mV/˚C
(Average Slope) +10.1 +10.1
Load Regulation T A =+25˚C ± 0.4 ± 1.0 ± 0.4 ± 1.0 mV/mA
(Note 3) 0≤IL≤1 mA T MIN≤TA≤TMAX ± 0.5 ± 3.0 ± 0.5 ± 3.0 mV/mA
Line Regulation T A =+25˚C ± 0.01 ± 0.05 ± 0.01 ± 0.05 mV/V
(Note 3) 4V≤V S≤30V ± 0.02 ± 0.1 ± 0.02 ± 0.1 mV/V
Quiescent Current V S =+5V, +25˚C 56 67 56 67 µA
(Note 9) V S =+5V 105 131 91 114 µA
V S =+30V, +25˚C 56.2 68 56.2 68 µA
V S =+30V 105.5 133 91.5 116 µA
Change of 4V≤VS≤30V, +25˚C 0.2 1.0 0.2 1.0 µA
Quiescent Current 4V≤V S≤30V 0.5 2.0 0.5 2.0 µA
(Note 3)
Temperature +0.39 +0.5 +0.39 +0.5 µA/˚C
Coefficient of
Quiescent Current
Minimum Temperature In circuit of +1.5 +2.0 +1.5 +2.0 ˚C
for Rated Accuracy Figure 1, IL =0
Long Term Stability T J =TMAX, for ± 0.08 ± 0.08 ˚C
1000 hours

3 www.national.com
LM35
Electrical Characteristics
(Notes 1, 6)
LM35 LM35C, LM35D
Parameter Conditions Tested Design Tested Design Units
Typical Limit Limit Typical Limit Limit (Max.)
(Note 4) (Note 5) (Note 4) (Note 5)
Accuracy, T A =+25˚C ± 0.4 ± 1.0 ± 0.4 ± 1.0 ˚C
LM35, LM35C T A =−10˚C ± 0.5 ± 0.5 ± 1.5 ˚C
(Note 7) T A =TMAX ± 0.8 ± 1.5 ± 0.8 ± 1.5 ˚C
T A =TMIN ± 0.8 ± 1.5 ± 0.8 ± 2.0 ˚C
Accuracy, LM35D T A =+25˚C ± 0.6 ± 1.5 ˚C
(Note 7) TA =TMAX ± 0.9 ± 2.0 ˚C
TA =TMIN ± 0.9 ± 2.0 ˚C
Nonlinearity T MIN≤TA≤TMAX ± 0.3 ± 0.5 ± 0.2 ± 0.5 ˚C
(Note 8)
Sensor Gain T MIN≤TA≤TMAX +10.0 +9.8, +10.0 +9.8, mV/˚C
(Average Slope) +10.2 +10.2
Load Regulation T A =+25˚C ± 0.4 ± 2.0 ± 0.4 ± 2.0 mV/mA
(Note 3) 0≤IL≤1 mA T MIN≤TA≤TMAX ± 0.5 ± 5.0 ± 0.5 ± 5.0 mV/mA
Line Regulation T A =+25˚C ± 0.01 ± 0.1 ± 0.01 ± 0.1 mV/V
(Note 3) 4V≤V S≤30V ± 0.02 ± 0.2 ± 0.02 ± 0.2 mV/V
Quiescent Current V S =+5V, +25˚C 56 80 56 80 µA
(Note 9) V S =+5V 105 158 91 138 µA
V S =+30V, +25˚C 56.2 82 56.2 82 µA
V S =+30V 105.5 161 91.5 141 µA
Change of 4V≤VS≤30V, +25˚C 0.2 2.0 0.2 2.0 µA
Quiescent Current 4V≤V S≤30V 0.5 3.0 0.5 3.0 µA
(Note 3)
Temperature +0.39 +0.7 +0.39 +0.7 µA/˚C
Coefficient of
Quiescent Current
Minimum Temperature In circuit of +1.5 +2.0 +1.5 +2.0 ˚C
for Rated Accuracy Figure 1, IL =0
Long Term Stability T J =TMAX, for ± 0.08 ± 0.08 ˚C
1000 hours
Note 1: Unless otherwise noted, these specifications apply: −55˚C≤TJ≤+150˚C for the LM35 and LM35A; −40˚≤TJ≤+110˚C for the LM35C and LM35CA; and
0˚≤TJ≤+100˚C for the LM35D. VS =+5Vdc and ILOAD =50 µA, in the circuit of Figure 2. These specifications also apply from +2˚C to TMAX in the circuit of Figure 1.
Specifications in boldface apply over the full rated temperature range.
Note 2: Thermal resistance of the TO-46 package is 400˚C/W, junction to ambient, and 24˚C/W junction to case. Thermal resistance of the TO-92 package is
180˚C/W junction to ambient. Thermal resistance of the small outline molded package is 220˚C/W junction to ambient. Thermal resistance of the TO-220 package
is 90˚C/W junction to ambient. For additional thermal resistance information see table in the Applications section.
Note 3: Regulation is measured at constant junction temperature, using pulse testing with a low duty cycle. Changes in output due to heating effects can be
computed by multiplying the internal dissipation by the thermal resistance.
Note 4: Tested Limits are guaranteed and 100% tested in production.
Note 5: Design Limits are guaranteed (but not 100% production tested) over the indicated temperature and supply voltage ranges. These limits are not used to
calculate outgoing quality levels.
Note 6: Specifications in boldface apply over the full rated temperature range.
Note 7: Accuracy is defined as the error between the output voltage and 10mv/˚C times the device’s case temperature, at specified conditions of voltage, current,
and temperature (expressed in ˚C).
Note 8: Nonlinearity is defined as the deviation of the output-voltage-versus-temperature curve from the best-fit straight line, over the device’s rated temperature
range.
Note 9: Quiescent current is defined in the circuit of Figure 1.
Note 10: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. DC and AC electrical specifications do not apply when operating
the device beyond its rated operating conditions. See Note 1.
Note 11: Human body model, 100 pF discharged through a 1.5 kΩ resistor.
Note 12: See AN-450 “Surface Mounting Methods and Their Effect on Product Reliability” or the section titled “Surface Mount” found in a current National
Semiconductor Linear Data Book for other methods of soldering surface mount devices.

www.national.com 4
 LM35
Typical Performance Characteristics
Thermal Resistance Thermal Time Constant Thermal Response
Junction to Air in Still Air

DS005516-26
DS005516-25 DS005516-27

Thermal Response in Minimum Supply Quiescent Current

Stirred Oil Bath Voltage vs. Temperature vs. Temperature
(In Circuit of Figure 1.)

DS005516-29
DS005516-28

DS005516-30

Quiescent Current Accuracy vs. Temperature Accuracy vs. Temperature

vs. Temperature (Guaranteed) (Guaranteed)
(In Circuit of Figure 2.)

DS005516-32 DS005516-33

DS005516-31

5 www.national.com
LM35
Typical Performance Characteristics (Continued)

Noise Voltage Start-Up Response

DS005516-34 DS005516-35

Applications The TO-46 metal package can also be soldered to a metal

surface or pipe without damage. Of course, in that case the
The LM35 can be applied easily in the same way as other V− terminal of the circuit will be grounded to that metal.
integrated-circuit temperature sensors. It can be glued or Alternatively, the LM35 can be mounted inside a sealed-end
cemented to a surface and its temperature will be within metal tube, and can then be dipped into a bath or screwed
about 0.01˚C of the surface temperature. into a threaded hole in a tank. As with any IC, the LM35 and
This presumes that the ambient air temperature is almost the accompanying wiring and circuits must be kept insulated and
same as the surface temperature; if the air temperature were dry, to avoid leakage and corrosion. This is especially true if
much higher or lower than the surface temperature, the the circuit may operate at cold temperatures where conden-
actual temperature of the LM35 die would be at an interme- sation can occur. Printed-circuit coatings and varnishes such
diate temperature between the surface temperature and the as Humiseal and epoxy paints or dips are often used to
air temperature. This is expecially true for the TO-92 plastic insure that moisture cannot corrode the LM35 or its connec-
package, where the copper leads are the principal thermal tions.
path to carry heat into the device, so its temperature might These devices are sometimes soldered to a small
be closer to the air temperature than to the surface tempera- light-weight heat fin, to decrease the thermal time constant
ture. and speed up the response in slowly-moving air. On the
To minimize this problem, be sure that the wiring to the other hand, a small thermal mass may be added to the
LM35, as it leaves the device, is held at the same tempera- sensor, to give the steadiest reading despite small deviations
ture as the surface of interest. The easiest way to do this is in the air temperature.
to cover up these wires with a bead of epoxy which will
insure that the leads and wires are all at the same tempera-
ture as the surface, and that the LM35 die’s temperature will
not be affected by the air temperature.

Temperature Rise of LM35 Due To Self-heating (Thermal Resistance,θJA)

TO-46, TO-46*, TO-92, TO-92**, SO-8 SO-8** TO-220
no heat small heat fin no heat small heat fin no heat small heat fin no heat
sink sink sink sink
Still air 400˚C/W 100˚C/W 180˚C/W 140˚C/W 220˚C/W 110˚C/W 90˚C/W
Moving air 100˚C/W 40˚C/W 90˚C/W 70˚C/W 105˚C/W 90˚C/W 26˚C/W
Still oil 100˚C/W 40˚C/W 90˚C/W 70˚C/W
Stirred oil 50˚C/W 30˚C/W 45˚C/W 40˚C/W
(Clamped to metal,
Infinite heat sink) (24˚C/W) (55˚C/W)

*Wakefield type 201, or 1" disc of 0.020" sheet brass, soldered to case, or similar.
**TO-92 and SO-8 packages glued and leads soldered to 1" square of 1/16" printed circuit board with 2 oz. foil or similar.

www.national.com 6
 LM35
Typical Applications

DS005516-19

FIGURE 3. LM35 with Decoupling from Capacitive Load

DS005516-6

FIGURE 6. Two-Wire Remote Temperature Sensor

(Output Referred to Ground)

DS005516-20

FIGURE 4. LM35 with R-C Damper

CAPACITIVE LOADS
Like most micropower circuits, the LM35 has a limited ability
to drive heavy capacitive loads. The LM35 by itself is able to
drive 50 pf without special precautions. If heavier loads are
anticipated, it is easy to isolate or decouple the load with a
resistor; see Figure 3. Or you can improve the tolerance of
capacitance with a series R-C damper from output to
ground; see Figure 4.
When the LM35 is applied with a 200Ω load resistor as DS005516-7

shown in Figure 5, Figure 6 or Figure 8 it is relatively immune FIGURE 7. Temperature Sensor, Single Supply, −55˚ to
to wiring capacitance because the capacitance forms a by- +150˚C
pass from ground to input, not on the output. However, as
with any linear circuit connected to wires in a hostile envi-
ronment, its performance can be affected adversely by in-
tense electromagnetic sources such as relays, radio trans-
mitters, motors with arcing brushes, SCR transients, etc, as
its wiring can act as a receiving antenna and its internal
junctions can act as rectifiers. For best results in such cases,
a bypass capacitor from VIN to ground and a series R-C
damper such as 75Ω in series with 0.2 or 1 µF from output to
ground are often useful. These are shown in Figure 13,
Figure 14, and Figure 16.

DS005516-8

FIGURE 8. Two-Wire Remote Temperature Sensor

(Output Referred to Ground)

DS005516-5

FIGURE 5. Two-Wire Remote Temperature Sensor

(Grounded Sensor)

DS005516-9

FIGURE 9. 4-To-20 mA Current Source (0˚C to +100˚C)

7 www.national.com
LM35
Typical Applications (Continued)

DS005516-11

FIGURE 11. Centigrade Thermometer (Analog Meter)

DS005516-10

FIGURE 10. Fahrenheit Thermometer

DS005516-12

FIGURE 12. Fahrenheit ThermometerExpanded Scale

Thermometer
(50˚ to 80˚ Fahrenheit, for Example Shown)

DS005516-13

FIGURE 13. Temperature To Digital Converter (Serial Output) (+128˚C Full Scale)

DS005516-14

FIGURE 14. Temperature To Digital Converter (Parallel TRI-STATE™ Outputs for

Standard Data Bus to µP Interface) (128˚C Full Scale)

www.national.com 8
 LM35
Typical Applications (Continued)

DS005516-16

* =1% or 2% film resistor

Trim RB for VB =3.075V
Trim RC for VC =1.955V
Trim RA for VA =0.075V + 100mV/˚C x Tambient
Example, VA =2.275V at 22˚C

FIGURE 15. Bar-Graph Temperature Display (Dot Mode)

DS005516-15

FIGURE 16. LM35 With Voltage-To-Frequency Converter And Isolated Output

(2˚C to +150˚C; 20 Hz to 1500 Hz)

9 www.national.com
LM35
Block Diagram

DS005516-23

www.national.com 10
 LM35
Physical Dimensions inches (millimeters) unless otherwise noted

TO-46 Metal Can Package (H)

Order Number LM35H, LM35AH, LM35CH,
LM35CAH, or LM35DH
NS Package Number H03H

SO-8 Molded Small Outline Package (M)

Order Number LM35DM
NS Package Number M08A

11 www.national.com
LM35
Physical Dimensions inches (millimeters) unless otherwise noted (Continued)

Power Package TO-220 (T)

Order Number LM35DT
NS Package Number TA03F

www.national.com 12
 LM35 Precision Centigrade Temperature Sensors
Physical Dimensions inches (millimeters) unless otherwise noted (Continued)

TO-92 Plastic Package (Z)

Order Number LM35CZ, LM35CAZ or LM35DZ
NS Package Number Z03A

LIFE SUPPORT POLICY

NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT
DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL
COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein:
1. Life support devices or systems are devices or 2. A critical component is any component of a life
systems which, (a) are intended for surgical implant support device or system whose failure to perform
into the body, or (b) support or sustain life, and can be reasonably expected to cause the failure of
whose failure to perform when properly used in the life support device or system, or to affect its
accordance with instructions for use provided in the safety or effectiveness.
labeling, can be reasonably expected to result in a
significant injury to the user.
National Semiconductor National Semiconductor National Semiconductor National Semiconductor
Corporation Europe Asia Pacific Customer Japan Ltd.
Americas Fax: +49 (0) 180-530 85 86 Response Group Tel: 81-3-5639-7560
Tel: 1-800-272-9959 Email: [email protected] Tel: 65-2544466 Fax: 81-3-5639-7507
Fax: 1-800-737-7018 Deutsch Tel: +49 (0) 69 9508 6208 Fax: 65-2504466
Email: [email protected] English Tel: +44 (0) 870 24 0 2171 Email: [email protected]
www.national.com Français Tel: +33 (0) 1 41 91 8790

National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.