Scribd
Upload
16 views5 pages

Lab 3 Final

This experiment investigates Reynolds number using a Reynolds number apparatus. Reynolds number describes the ratio of inertial to viscous forces and determines if flow is laminar or turbulent. The apparatus contains a water tank, clear tube, and dye injection point. As flow velocity increases, dye behavior changes from a steady line (laminar flow) to erratic movement and diffusion (turbulent flow). Flow rates are measured at these transition points to calculate Reynolds numbers characterizing the flow regimes.

Uploaded by

rosaleszimon
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
16 views5 pages

Lab 3 Final

This experiment investigates Reynolds number using a Reynolds number apparatus. Reynolds number describes the ratio of inertial to viscous forces and determines if flow is laminar or turbulent. The apparatus contains a water tank, clear tube, and dye injection point. As flow velocity increases, dye behavior changes from a steady line (laminar flow) to erratic movement and diffusion (turbulent flow). Flow rates are measured at these transition points to calculate Reynolds numbers characterizing the flow regimes.

Uploaded by

rosaleszimon
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 5

Name: Date Performed:

Section: Date Submitted:


Instructor:

EXPERIMENT NO.
REYNOLDS NUMBER
OBJECTIVE: To investigate Reynolds number for water using Reynolds Number apparatus.
APPARATUS:
a.) Reynolds Apparatus test rig
b.) A dye and stop watch

THEORY:
Fluid distribution networks and heating and cooling applications frequently involve liquid
or gas movement through pipes and ducts. In this type of application, a pump or fan forces the fluid
through a flow section. There are two types of fluid flow through a pipe: laminar and turbulent.
Osborn Reynolds was the one who initially proved these two sorts existed. A number of factors,
including the fluid's temperature and type, velocity (V), flow rate (Q), diameter of the circular pipe
(D), and velocity (V), influence the change from laminar to turbulent flow. Osborne Reynolds
conducted a thorough experiment in the 1880s and found that the fluid's ratio of viscous to inertial
forces determined the flow regime. This ratio, which is stated for internal flow in a circular pipe, is
known as the Reynolds number. The following represents the Reynolds number (Re):

Re = Inertial forces = V D = ρVD


Viscous forces ν μ

Where;
V = flow velocity, m/s
D = diameter of tube, m
ν = kinematics viscosity of the fluid, m2/s (μ/ρ)
μ = viscosity of fluid, Ns/m2 (kg/m.s)
ρ = density of water, kg/m3

The water velocity (V) is determined by:

V = Flowrate (m3/s) = Q (m/s)


Cross section area (m2) A

Where, flow rate (Q) is given by:

Q = Water volume (m3) = Q (m3/s)


Time (s) t
The Reynolds Number equipment will be utilized in this experiment. This device is made comprised
of a water-filled constant head supply tank. This tank has a bell-mouth exit that has a clear tube
attached to it. There is a regulating valve at the tube's exit. Above the supply tank is installed a dye
tank filled with colored dye. A dye injection is made in the middle of the pipe while water flows
through it.

The dye maintains its filamentous shape at lower velocities, suggesting the presence of laminar
flow. The dye becomes erratic and waves as the velocity increases and a transitional flow is
attained. An additional rise in velocity reveals that the dye filament becomes increasingly erratic,
and eventually the dye diffuses over the tube's whole cross section. At this point, the water flow
pattern is quite erratic and the turbulent flow has evolved.
PROCEDURE:

1. Fully open by-pass valve.


2. Fully close flow control valve.
3. Start the pump. Wait until water is discharged from by-pass valve.
4. Slowly close the by-pass valve. The water will be pumped into supply tank. Control the by-
pass valve until the water start filling the transparent tube. At the same time, control the by-
pass valve so that water level in supply tank remains constant at 70% of supply tank capacity.
5. Slowly open the flow control valve to remove all air bubble inside transparent tube. Then
close the flow control valve. Ensure the water level in supply tank remains constant at 70%
of supply tank capacity by control by-pass valve.
6. Start the dye injection. Then, slowly open flow control valve. Wait for some time. A steady
line of dye will be observed. Adjust dye flow, if required.
7. During steady line phase (laminar region), take the time for 135 ml of water.
8. Slowly open the flow control valve, the water flow will increase. In the same time ensure
water level in supply tank remains constant. As the increasing of the water flow, dye line will
be disturbed. Measure this flow rate.
9. Further increase the flow by open the flow control valve. The disturbances of dye line will
increase and at certain flow; the dye line diffuses over the entire cross section. Measure this
flow rate.
10. Slightly increase the flow and then slowly reduce the flow. Measure the flow rate at which
diffused dye tends to become steady, (the beginning of transition zone while reducing
velocity.)
11. Further reduce the flow and measure the flow rate at which dye line becomes straight and
steady.
12. Record your observation in Table 5.1. Calculate Reynolds Number of each the flow.

COMPUTATIONS:
OBSERVATIONS:

CONCLUSION:
DOCUMENTATION:

You might also like