I C Engines

• An internal combustion engine is a

device in which the chemical energy
of the fuel is released inside the engine
and used directly for mechanical work.

Examples:
– Piston Engines
– Gas Turbine Engines (Open Cycle)
– Rocket Engines

2
 History of IC engines:

1700s - Steam engines (external combustion engines)

1860 - Lenoir engine (η = 5%)
1867 - Otto-Langen engine (η = 11%, 90 RPM max.)
1876 - Otto four stroke “spark ignition” engine
(η = 14%, 160 RPM max.)
1880s - Two stroke engine
1892 - Diesel four stroke “compression ignition” engine
1957 - Wankel “rotary” engine

3
Historical IC Engines

FLYWHEEL

4
 Engine Anatomy

Air cleaner

Carburetor Camshaft

Rocker arm

Intake valve
Cam sprocket Exhaust valve
Piston

Connecting rod
Timing belt

Timing belt Crankshaft

tensor

Oil pump
Crank sprocket Oil pickup 5
 V-6 Engine

Inlet
runner
Air intake
manifold

6
 4 Stroke SI Engine Cycle
Intake Valve Exhaust Valve 4
1 2 Exhaust 3
Intake
Manifold Manifold

Spark
Cylinder Plug

Piston

Connecting
Crank
Rod
Crankcase

Compression Stroke Power Stroke Exhaust Stroke

Intake Stroke Fuel-air mixture burns,
Intake valve opens, Both valves closed, Exhaust valve open,
increasing temperature exhaust products are
admitting fuel and air. Fuel/air mixture is
and pressure, expansion displaced from cylinder.
Exhaust valve closed compressed by rising
of combustion gases Intake valve opens
for most of stroke piston. Spark ignites
mixture near end of drives piston down. Both near end of stroke.
stroke. valves closed - exhaust
valve opens near end 7
of stroke
 Four-Stroke Diesel Engine
• Intake stroke
– Intake valve open, exhaust valve shut
– Piston travels from TDC to BDC
– Air drawn in
• Compression stroke
– Intake and exhaust valves shut
– Piston travels from BDC to TDC
– Temperature and pressure of air increase
• Power stroke
– Intake and exhaust valves shut
– Fuel injected into cylinder and ignites
– Piston forced from TDC to BDC
• Exhaust stroke
– Intake valve shut, exhaust valve open
– Piston moves from BDC to TDC
– Combustion gases expelled
8
9
10
11
 Two Stroke Spark Ignition Engines

Stroke 1: Fuel-air mixture is introduced into the

cylinder and is then compressed,
combustion initiated at the end of the stroke

Stroke 2: Combustion products expand doing

work and then exhausted

•Power is delivered to the crankshaft

on every revolution

12
 Two Stroke Spark Ignition Engine

Exhaust
Port*
Transfer
Port*
Fuel-air-oil
mixture

Reed
valve
Expansion Exhaust Intake (“Scavenging”)
Crank
shaft

*No valves and

thus no camshaft

Fuel-air-oil
mixture
Compression Ignition 13
Intake: The fuel/air
mixture is first drawn into
the crankcase by the
vacuum created during
the upward stroke of the
piston. The illustrated
engine features a poppet
intake valve, however
many engines use a rotary
valve incorporated into
the crankshaft.

14
During the downward stroke the poppet valve is
forced closed by the increased crankcase
pressure. The fuel mixture is then compressed in the
crankcase during the remainder of the stroke.

15
Transfer/Exhaust: Towards the
end of the stroke, the piston
exposes the intake port,
allowing the compressed
fuel/air mixture in the
crankcase to escape around
the piston into the main
cylinder. This expels the
exhaust gasses out the
exhaust port, usually located
on the opposite side of the
cylinder. Unfortunately,
some of the fresh fuel
mixture is usually expelled as
well.
16
Compression: The
piston then rises,
driven by flywheel
momentum, and
compresses the fuel
mixture.

(At the same time,

another intake stroke
is happening beneath
the piston).

17
Power: At the top of the
stroke the spark plug
ignites the fuel mixture.
The burning fuel
expands, driving the
piston downward, to
complete the cycle.

18
 Two Stroke Spark Ignition Engine

Exhaust
port

Fuel-air-oil
mixture
compressed

Check
valve
Expansion Exhaust Intake (“Scavenging”)
Crank
shaft

Fuel-air-oil
mixture

Compression Ignition 19
 Two Stroke Engines

• Small Engines – Absence of valve

mechanism makes cheaper, compact
and lighter engines

• Large Engines – That operates at a low

RPM. Requires a power stroke from
every revolution for smooth operation.

20
 Two Stroke Engines

• Two stroke engines have

advantages over four stroke:
– simplified construction (no valves)
– fire once every revolution for a
significant power boost

• Great power to weight ratio

21
 The two stroke cycle
• The two stroke engine ignites every
revolution of the crankshaft. These
engines overlap operations to
reduce parts while maintaining
power.
• In simpler words, in a two stroke
engine there are only:
– Compression
– Combustion
• Thus, Two Strokes.
22
 2 stroke compared to 4 stroke

• In two stroke engines • In four stroke

the crankcase is a engines the
pressurization crankcase is
chamber to force separate from the
fuel/oil/air into the compression
cylinder. Here, we chamber. This
mix oil and gas to allows the use of
lubricate internal heavy oil for
parts. lubrication.

23
 Disadvantages of a two-stroke

• The engines do not last as long

due to poor lubrication.
• Increased heating due to more
number of strokes limits the
maximum speed.
• The engines do not use fuel
efficiently.
• These engines produce a lot of
pollution.
24
 Summary

• During scavenging (when inlet and exhaust

ports remain open for sometime), some fresh
charge may escape through exhaust. This
leads to higher fuel consumption and
lower thermal efficiency.

• Greater cooling & lubrication requirements.

• Power output is only more than 30 % and

not doubled.

25
 Single Cylinder Engine

Single-cylinder engine gives one power stroke per

crank revolution (360 CA) for 2 stroke, or every two
revolutions for 4 stroke.

The torque pulses on the crank shaft are widely

spaced, and engine vibration and smoothness are
significant problems.
4-stroke

2-stroke

0 CA 180 CA 360 CA 540 CA 720 CA 180 CA

(TC) (TC) (TC)

Used in small engine applications where

engine size is more important
26
27
28
 4 Stroke vs. 2 Stroke

• 2 Stroke needs a blower and will usually use a

supercharger
• 2 Stroke combustion process not as complete
(more pollution)
• 2 stroke engines weigh less and have higher RPM
operating speeds.
• 4 stroke engine has Intake, Compression, Power,
and Exhaust strokes.
• 2 stroke has power and compression.
• 2 strokes used more for emergencies, 4 strokes
used more for propulsion
30
 References
1. Crouse WH, and Anglin DL, DL (1985), Automotive Engines, Tata McGraw Hill.
2. Eastop TD, and McConkey A, (1993), Applied Thermodynamics for Engg.
Technologists, Addison Wisley.
3. Fergusan CR, and Kirkpatrick AT, (2001), Internal Combustion Engines, John
Wiley & Sons.
4. Ganesan V, (2003), Internal Combustion Engines, Tata McGraw Hill.
5. Gill PW, Smith JH, and Ziurys EJ, (1959), Fundamentals of I. C. Engines, Oxford
and IBH Pub Ltd.
6. Heisler H, (1999), Vehicle and Engine Technology, Arnold Publishers.
7. Heywood JB, (1989), Internal Combustion Engine Fundamentals, McGraw Hill.
8. Heywood JB, and Sher E, (1999), The Two-Stroke Cycle Engine, Taylor & Francis.
9. Joel R, (1996), Basic Engineering Thermodynamics, Addison-Wesley.
10. Mathur ML, and Sharma RP, (1994), A Course in Internal Combustion Engines,
Dhanpat Rai & Sons, New Delhi.
11. Pulkrabek WW, (1997), Engineering Fundamentals of the I. C. Engine, Prentice Hall.
12. Rogers GFC, and Mayhew YR, YR (1992), Engineering Thermodynamics, Addison
Wisley.
13. Srinivasan S, (2001), Automotive Engines, Tata McGraw Hill.
14. Stone R, (1992), Internal Combustion Engines, The Macmillan Press Limited, London.
15. Taylor CF, (1985), The Internal-Combustion Engine in Theory and Practice, Vol. 1 & 2,
The MIT Press, Cambridge, Massachusetts.
31
 Web Resources
1. http://www.mne.psu.edu/simpson/courses
2. http://me.queensu.ca/courses
3. http://www.keveney.com/twostroke.html
4. http://www.eng.fsu.edu
5. http://www.personal.utulsa.edu
6. http://www.glenroseffa.org/
7. http://www.howstuffworks.com
8. http://www.me.psu.edu
9. http://www.uic.edu/classes/me/ me429/lecture-air-cyc-web%5B1%5D.ppt
10. http://www.osti.gov/fcvt/HETE2004/Stable.pdf
11. http://www.rmi.org/sitepages/pid457.php
12. http://www.tpub.com/content/engine/14081/css
13. http://webpages.csus.edu
14. http://www.nebo.edu/misc/learning_resources/ ppt/6-12
15. http://netlogo.modelingcomplexity.org/Small_engines.ppt
16. http://www.ku.edu/~kunrotc/academics/180/Lesson%2008%20Diesel.ppt
17. http://navsci.berkeley.edu/NS10/PPT/
18. http://www.career-center.org/ secondary/powerpoint/sge-parts.ppt
19. http://mcdetflw.tecom.usmc.mil
20. http://ferl.becta.org.uk/display.cfm
21. http://www.eng.fsu.edu/ME_senior_design/2002/folder14/ccd/Combustion
22. http://www.me.udel.edu
23. http://online.physics.uiuc.edu/courses/phys140
24. http://widget.ecn.purdue.edu/~yanchen/ME200/ME200-8.ppt -
32