Scribd
Upload
32 views5 pages

Filtration Method BSC Ii Sem

There are several filtration methods including gravity, hot, and vacuum filtration. The appropriate method depends on factors like whether the solid or filtrate is being collected, the volume of solution, amount of solid, and fineness of the solid. Gravity filtration is common but vacuum filtration is faster. Hot filtration can prevent crystallization in the funnel. Vacuum filtration uses a Buchner or Hirsch funnel with filter paper and vacuum to draw the solution through. Proper setup and technique is important for effective filtration.

Uploaded by

Singh Ji
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
32 views5 pages

Filtration Method BSC Ii Sem

There are several filtration methods including gravity, hot, and vacuum filtration. The appropriate method depends on factors like whether the solid or filtrate is being collected, the volume of solution, amount of solid, and fineness of the solid. Gravity filtration is common but vacuum filtration is faster. Hot filtration can prevent crystallization in the funnel. Vacuum filtration uses a Buchner or Hirsch funnel with filter paper and vacuum to draw the solution through. Proper setup and technique is important for effective filtration.

Uploaded by

Singh Ji
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 5

FILTRATION METHODS

There are several filtration methods : simple or gravity, hot and vacuum filtrations. The selection of the appropriate
method is typically dictated by the nature of the experimental situation. The answers to each these questions help
dictate what type of set up is required.

1. Are you collecting the solid or the filtrate (solution) ? If you are collecting the solid, vacuum methods are likely
best as they are faster. If you are collecting the filtrate (solution), gravity filtration methods are often preferred.
2. How much solution is there to filter ? If you have a large volume to filter, gravity filtration is probably the better
choice. Vacuum filtration is fast but if you need to empty the flask part way through you have to release the
pressure and remove the funnel to do this which increases the risk of spills and slows things down.
3. How much solid is being collected ? If only a small amount is being collected, a vacuum filtration using the
Hirsch funnel is preferred.
4. How fine is the solid ? If it’s a fine solid, regular filtration might be very slow, so use vacuum filtration.
5. Will unwanted crystallisation occur in the filter funnel ? If yes, use hot filtration.

a. The filter paper


First, make sure you use the appropriate size filter paper. This is most important for vacuum filtration
where the paper should smaller in diameter than the base of Buchner or Hirsch funnel (but it must cover all the
holes) and should sit flat on the bottom of the funnel with no creases or folds.
Second, folding the filter paper. There are two ways to fold filter papers, the "conventional" method and
"fluted".
Here are two videos showing how to fold filter papers.
The steps to flute the filter paper are shown. First, fold in

half; open and fold in half at 90° to the first fold,

subsequently align adjacent folds and make new folds


bisecting the previous folds until a fan-like arrangement is
obtained. Pleat into a fan by folding each segment in the
opposite direction to its neighbours, in accordion-like
fashion. When opened out the complete fan-like fluted
paper results.
Fluting the filter paper maximises the rate at which he
liquid may flow through the filter paper by increasing the
surface area and by allowing air to enter the flask along
its sides to permit rapid pressure equalisation.

b. Gravity or simple filtration


This is the most common method of filtration and is used to remove an insoluble solid material from a
solution. The solid could be the required product or an impurity or an additive such as a drying agent. A filter paper
is folded (conventional or fluted) and placed in a filter funnel which is then placed in the neck of an Erlenmeyer
flask or supported in a clamp or ring stand. The solution to be filtered is then slowly and carefully poured into the
funnel taking care not to fill the funnel above the edge of the filter paper. Here are two videos showing this filtration
method .

Gravity filtration with a fluted filter paper


c. Hot filtration

Never heat organic solvents with a Bunsen burner. Use a hot plate or a hot water
bath on a hot plate.

Sometimes during a gravity filtration, crystals can start to grow in the filter funnel and may block the funnel,
stopping filtration. This problem can be avoided by using a hot filtration where the whole filtration apparatus is heated
in order to prevent the solution from cooling significantly.
The hot filtration process is best carried out using a fluted filter
paper and a stemless filter funnel. Support the stemless filter
funnel on an iron ring clamp if it is at all insecure (see the lower
picture). If pressure builds up in the flask due to the presence of
hot vapours, the filtering action will slow down or even stop. The
use of the fluted paper reduces this problem. The hot solution
should be filtered quickly through the fluted paper in a stemless
filter funnel into an Erlenmeyer flask. Alternatively, a small piece
of wire or paper may be inserted between funnel and Erlenmeyer
to prevent formation of a seal and subsequent pressure build-up. If
crystals start to form in the paper or in the filter funnel, then the
Erlenmeyer containing a few drops of pure solvent with the funnel
and paper in place should be heated on a steam bath (or a hot
plate) and the entire filtration procedure carried out on the steam
bath. Hot solvent may be added to remove any crystals appearing
in the filter paper.

Do not use metal tongs or a test-tube holder to hold the hot


Erlenmeyer flask while pouring the liquid since it is too easy to
drop the flask. A better convenient simple holder may be
fashioned from a piece of paper towel folded into a strip and
pinched around the neck of the flask.
d. Vacuum filtration

In a vacuum filtration, the solution to be filtered is


drawn through the filter paper by applying a vacuum to
a filter flask with a side arm adaptor (also known as a
Buchner flask). Vacuum filtration is typically a fast and
efficient way of filtering.

The crystals are collected by swirling the mixture of the


solid and liquid and then pouring quickly it into the
filtration apparatus. This typically comprises a Büchner
funnel fitted with the appropriate size filter paper; a
clamped filter flask with conical filter adapter, and a
vacuum applied to the side arm of the filter flask (see
left).

Vacuum filtration with a Buchner funnel

If smaller quantities are to be filtered the Hirsch funnel


(see left and below) and a small filter paper should be
used instead. If needed, the filter flask can be replaced
by a test tube with side arm. Again, the tube should be
clamped and the vacuum applied at the side arm using
the thick walled vacuum tubing.

When using vacuum filtration, it is very important


that the correct size of filter paper be used. The filter
paper should be flat (i.e. not folded up at the edges)
and should cover all the holes in the base of the funnel.
It is also important that the apparatus be clamped since
it is very easily tipped over usually resulting in loss of
the sample.

Vacuum filtration with a Hirsch funnel


To filter the crystals, assemble the apparatus, ensuring that the funnel is sealed into the flask; turn the aspirator tap
full on; moisten the filter paper with a little cold solvent to adhere the paper to the funnel, to prevent crystals from
creeping under the paper and through the filter. The mother liquor containing the crystals may now be filtered. The
crystals should then be rinsed with a small portion of cold solvent. Allow the crystals to remain exposed to the
vacuum for a few minutes in order to dry them. DISCONNECT THE TUBING BEFORE TURNING OFF THE
ASPIRATOR TAP. Thick-walled pressure
tube is used throughout the apparatus. A trap is used in conjunction with the water aspirator. If the water pressure in
the laboratory line drops suddenly, the pressure in the filter flask may become less than that in the water aspirator.
This would cause water to be drawn from the aspirator stream into the filter flask and would contaminate the filtrate.
The trap stops this reverse flow. A similar reverse flow would occur if the water flow at the aspirator were stopped
before disconnecting the tubing to the aspirator side-arm or opening the valve on the top of the water trap.

You might also like