Scribd
Upload
42 views26 pages

Traduce (01 26)

Refrigerador

Uploaded by

Francisco M
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF or read online on Scribd
42 views26 pages

Traduce (01 26)

Refrigerador

Uploaded by

Francisco M
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF or read online on Scribd
You are on page 1/ 26
> LG Asa lle DET IVE CAUTION BEFORE SERVICING THE UNIT, READ THE SAFETY PRECAUTIONS IN THIS MANUAL. MODEL : GR-B318SS COLOR : STAINLESS(ST) 3-8 DISPENSER, 2) Holding the inner side of the aispenser pull forward to remove. \2h by - 1) Pullout the drain “Tye bf 8) If nozzle is interfered with button, 4) Remove the push and pullout the bottom of lead wire. button, 4 CAUTION: When replacing the dispenser cover make sure the lead wire does NOT come off and the waterline Is nol pinched by the dispenser. 3-9 DISPLAY PCB ‘As shown below, remove 1 screw on the PCB king screw. Remove the display PCB fixing screw. 3-10 ICE BUTTON ASSEMBLY 1) Remove the 1 screw holding the lever. 2) Remove the spring from the hook. 3) Push and pullon the tab to remove. ® 4 nL | aL. Button Lever 3:11 WATER BUTTON ASSMEBLY 1) Remove screws, 2) Grasp the Button assembly and lit, Button Lover 9-12 ICE CORNER DOOR REPLACEMENT 1) Loosen the front screw as shown inthe picture, 2) Litt up the hinge with one hand, '3) Pull out the lee Corner Doar with the other hand. “ie 3-13 ICEMAKER REPLACEMENT ‘4 CAUTION: Mako sure that the motor housing is taped to the mold, not positioned correctly the cover will nat ft property 1) Remove 4 serows as shown, 2) Grasp the bottom of motor cover assembly and pull slowly, 3:14 SUB PCB FOR WORKING DISPENSER 1) Disconnect the wire hamess. 2) Remove 1 screw trom PCB and replace with new PCB. 8) Disconnect wire harness from wall of compartment. fe man mater -12- 5. CIRCUIT DIAGRAM @ LG Electronics NIWWATIGWASSVEMd 6. TROUBLESHOOTING 6-1 Error Code Summary 4 WARNING: When checking Resistance valves, make sure to rome rca ene en sorm:yann its en onr:pre nea Puttin and reeernaen vretsecey gins are re eee fa ene Se ee ai “Elenco org arn FE or mesma aro sects | Tear [oer wo | Erarzreion | Fee] Ruta | cor cemraton Fat — (Error cade (1) To (2) Result 22°F / -40°C 40 4a SOONTS) ASF /=25°C 30\a °F /-20°C 2342 SF /-15°C Ike 14°F 7 10°C 1310 23°F /—5°C 10 ka B2F 70°C 81a The sensor is determined by the temperature For example, 23\Qindicates -4°F. 8-2 Refrigerator Sensor Error (Er rS) No Checking flow Result & SVC Action 1 | check for a loose connection. 2 | Check the White to White, Result SVG Action 0.0 | Shon | Change the sensor BY OFF | Open | Replace the refrigerator Check the Temp and Other | Normal | resistance (Table-2) 70.2) Result 23°F / SC 3810 BF 70°C 3010 avr / 50 2412 50°F / 10°C 19510 BOF / 15°C 1610 The sensor Is determined by the temperature. For example, 30k indicates 32°F. -31- 8-3 Icing Sensor Error (Er IS) No Checking flow Result & SVC Action 1 Cheek for a loose connection. 2 Check the Blue to Blue. | Result SVC Aetion 0.0 | Shon | Change the sensor OFF | Open | Replace the refrigerator gamer | Normal | esstance Cable) - (1) To (2 Result 22°F /-30°C 4042 ASF /=25°C 201 oF / 20°C 231 BYF /-15°C I? ha 14°F /-10°C 1310 28°F /-50 101 32°F 06 8K % The sensor is determined by the temperature. For example, 23)Qindicates ~4°F. -32- 8-4 Defrost Sensor Error (F dS) Check the Brown to Brown, =CON7> No Checking flow Result & SVC Action 4 Check for a loose connection. 2 Check the Orange to Orange. Result ‘SVC Action 02 | Shon | Change the sensor OFF | Open | Replace the refrigerator ‘Check the Temp and Other | Normal | resistance (Table-3) - (702 Result 20°F /-5°C 980 32°F /0°C 3012 avr /5C SO°F / 10°C SO°F / 15°C The sensor is determined by the temperature. For example, 23k2 indicates -4 -33- 8-5 Defrost Sensor Error (R dS) No Checking flow Result & SVC Action 1 ‘Check for a loose connection. 2 ‘Check the Orange to Orange. Result ‘SVC Action 0. | Shon | Change the sensor OFF | Open | Replace the refrigerator ‘Check the Temp and Other | Normal | resistance (Table-3) ‘Check the Gray to Gray, (To (2) Result 23°F / ~5°C 3812 32°F /OC 30 4a 40°F (50 2410 50°F / 10°C 19.540 59°F /15C 16 ko nsor is determined by mperature, For example, 23kQindicates -4 8-6 Defrost Heater Error (F dH) No Checking flow Result & SVC Action 1 | check the Door gasket, Result | SVC Action 2 | check the Detrost control part 09 Goto the 3 Fuse-M ‘Other | Change Fuse Det | a4-az@ | Gotoihes Der. Det’ Heater | Other | Change Fuso M ater ear: per | 22Kr Goto thea 55 sensor [~ ore | Repace poo M 3 | input Test 3 mode. (Push the button 3 times) 4 | cheek the Biue to Orange. Result SVG Action 12~116V Go to the 5 ov Replace Main PCB 5 Release the test mode. push the button 1 times. (normal) 6 Check the Blue to Orange. Result ‘SVC Action ov Explain to customer 112~116V | Replace Main PCB =95 8-7 Defrost Heater Error (R dH) No Checking flow Result & SVC Action 1 | Cheek the Door gasket, Part_| Result | SVC Aclion 2 | Check the Detrost control part, 0.8 Go tothe 3 Fuse-M Other | Change Fuse Def | a4-a2.0 | Gotoines Det’ Def Heater | Other _| Change Fuse-M ater Heater | | 5 —Taeiap | Gotothe 8 Sensor ns OFF | Replace product ™ 3 | Input Test 3 Mode. (Push the button 3 times) 4 | Cheek the Blue to Yellow, Result SVC Action 112~116V | Gotothes ov Replace Main PCB 5 | Release the test mode. push the button 1 times. (normal) 6 | Check the Blue to Yellow. Result ‘SVC Action ov Explain to customer 112~116V__| Replace Main PCB 8-8 Refrigerator Fan Error (Er rF) No Checking flow Result & SVC Action Reset the unit and Input Test 1 Mode. (Push the button 1 time) Open the freezer door and Check the air flow. ® While an error code is displayed, the fan is not working SVC Action Goto 3 Goto4 Check the Fan motor voltage. ma Point | Result ‘SVE Action (1) = (@) | Below 12v | Change the PCB (1)=(@) | Oor5V | Change the motor 8-9 Freezer Fan Error (Er FF) No Checking flow Result & SVC Action 1 Reset the unit and Input Test 1 Mode. (Push the button 1 time) 2 | Qpentmetraeser door and check he ai — 8 While an error code is displayed, P| No windy | Gotos the fan isnot working. BS winty | cows 3 Cheek the Fan motor. a Rotate fan using your hand. It fee! sticky, change the motor. (cause of ice or rust inside of motor) 4 Cheek the Fan motor voltage... (3)(2)(1) Point | Result ‘SVC Action (1) ~ (2) | Below 12v | Change the PCB () =) | OorSV_| Change the motor 8-10 Icing Fan Error (Er IF) No Checking tlow 1 Reset the unit and Input Test 1 Mode, (Push the button 1 time) (3) @) (1) 2 | Open tne treezar door and check the air GERRI VG Raa 28 While an error code is displayed, No windy | Go to the 3,4 the fan is not working Windy | Goto thes 3 | Chock the Connector, (Frozen caused the PCB short) 4 ‘Check the Fan motor voltage, ——-—_——_ joint | Result SVC Action (=) Below9V | Change the PCB ()-@) QorSV | Change the motor 8-11 Condenser Fan Error (Er CF) No Checking tlow Result & SVC Action 1 Reset the unit and Input Test 1 Mode, (Push the button 1 time) 2 | Check the tan rotating. Sanaa aVGAGET % While an error code is displayed, No windy | Check motor the fan isnot working. Windy | Gotothe4 =e : 3 | Check the Fan motor and surrounding. | Rotate fan using your hand. feel sticky, change the motor. == 4 Check the Fan motor voltage. (3) (2) (1) Point Result’ | SVC Action ()-@) Below 10 | Change the PCB (= @) Oor5V | Change the motor 8-12 Communication Error (Er CO) No Ghecking flow Result & SVC Action 1 | Cheek the loose connection. 2 | Cheek the White/Red, 7 EE 12 Go tothe Check the Hinge Other (loose connection) conins Ghange the Main PCB , 3 | Check the Orange to White/Red. Result SVC Action Oor5V_| Change the Display PCB Other Goto the 4 cONtOT 4 | Check the White/Black to White/Red. ce Result ‘SVC Action rdf es Oor5V | Change the Main PCB - ~ Other Goto the 5 cONtoT . 5 | Cheek the White/Red to Orange. Result SVC Action Oor5V_| Change the Display PCB Other Goto the 6 6 | Check the White/Red to White/Black, j Result SVC Action y j QorSV | Change the Main PCB Other | Explain to customer -41- 9. Troubleshooting Without Error Displa 9-1 Cube mode doesn't work a No Checking flow Result & SVC Action 1 Check the loose connection. 2 (Cheek the Black to White. Lever siw| Result ‘SVC Action (While pushing the lever S/W) pushing LU2215¥ | Gotothes “snes |” Other | Change PCB Not o-2v Go tothe 3 pushing [Other | Change PCB ‘ 3 Check the RED to White Red. (While pushing the lever S/W) aS) 9-12v | Gotothes Pushing Totner _| _ Change PCB + Not 0-2v | Gotothea a pushing ‘Other Change PCB = 4 | Check the resistance value. = re two feet | Eman io Replace Offer Geared Motor 99-1210 Explain (3) 10 (4) Replace Other | Geared Motor 42+ 9-2 Crush mode doesn't work No Checking flow Result & SVC Action 1 | Chock the loose connection. 2 | Check the Sky Blue to White, Lever siw] Result | SVC Action (While pushing the lever S/W) pushing L12=18V | Gotothes ushieg Other | Change PCB Not 0-2V Go to the 3 pushing | Other | Change PCB 3 | Chock the Black to White Red. [Sve hetion —] (While pushing the lever SW) [oSSeee eam 7 9-12V | Gotothes enw Other Change PCB Not 0-2V Go to the 4 L| pushing | Other ‘Change PCB 4 Check the resistance value. Point Result ‘SVC Action 31.4421 0 | Explain (1) to (2) T Replace Other | Geared Motor 9.9~ 12.1 2 Explain (3) to (4) Replace adh Geared Motor -43- 9-3 Water mode doesn't work No Checking tlow Result & SVC Action 1 ‘Check the loose connection, 2 | Check the Purple to White, Lever Resi ‘Retion (While pushing the lever S/W) eae - an 112-115V | Go tothe 3 Other | Change PCB Not 0-2v | Gotothes pushing |" Other | Change PCB Pushing 3 | Cheek the resistance value. STE ESE ER (1) (2) 3y(4) 360 ~ 4202 Explain 4) t0 2) aioe Other Water Valve 360-4200 | Explain ()t0(4) Roplace Other Water Valve Dispenser | Ice Maker Machine Room In door 9-4 Freezer room lamp doesn't work No ‘Checking flow Check the Freezer door switch. Check the door S/W resistance, Result & SVC Action feel sticky, Change the door siw. Status | Result ‘SVC Action 10 to the Normal 00 Go to the 3 not__| Change door SW Push |_Infinty Goto thes | SW Other | Change door SW 3 Check the Red/yellow to Pink. Status | Result ‘SVC Action 12V Go to the 4 Normal Other [Change the PCB 4 Check the Rad to Black. Status | Result ‘SVC Action 12V Go to the 5 Normal ———_—~_—_ Other | Change the LED Lamp 5 | Check the Black to White. Sa Syo Asien O~2v Explain to customer Closed Other | Change the Door S/W Open |_12¥_| Bilan customer Other | Change the LED Lamp 9-5 Refrigerator room lamp doesn’t work No Checking flow Result & SVC Action 1 Check the Refrigerator door switch. If feel sticky, Change the door siw. 2 | Check the door Switch resistance. Status | Result ‘SVC Action Goto the 3 Normal | 9 Other Change door Switch Push | Infinity Goto the 3 | SW | other | Change door Switch 3 | Check the Rediyellowto Pink, Sane inee Sve Action 12 Goto the 4 Normal ote Other_[ Change the PCB 4 Cheek the Red to Black. Status | Result ‘SVG Action 1 ih Normal av Goto the 5 Other _| Change the LED Lamp 5 | Check the Black to Blue. Siauia NRCC SVC Aeon O-2V Explain to customer Closed Other Change the Door SW Open _12¥_[ lain customer Other | Change the LED Lamp 9-6 Poor cooling in Fresh food section No Checking flow Result & SVC Action 1 | check the sensor resistance. = — 23°F /-5°C 38 Ka a2F/0°C 2010 ar /5C 26K SOF /10'C | 1950 x The sensor is determined by Lsersisc | 16a | the temperature. For example, 30\Qindicates 32°F. 2 | Resetthe unit and Input Test 1 Mode. (Push the button 1 time) 3. | Openthe fresh food door and Check the aaa Ghai airflow. Windy Go tothe 4 Check the R Fan motor No windy | Check the damper (Go tothe 8) 5 | Chock tho air temperature. aim =e Gold or not ? oid Explain to customer Check the Compressor Notcold | “And sealed system -47- Checking flow Cheek the R Fan motor voltage. wen. Result & SVC Action Point | Result "SVC Action (1)~ (2) | Below 12V | Change the PCB (1)=@) | OorSV | Change the mator 9-7 Poor cooling in Freezer compratment No Checking flow Result & SVC Action 1 | Chock the sensor resistance. OL aa 22°F / -30"C 4040 13°F 7 =25°C 3010 rF / 20°C 2312 SF /-19°C 7a ne 14°F /=10°C 1310 .8 The sensor is determined by the temperature, 23°F /-8C 1010 For example, 234Qindicates -4°F. SEF 70C ri 2 | Reset the unit and Input Test 1 Mode. (Push the button 1 time) 3 | pen the treezer door and Check thea Sie IC RENA Windy Go tothe 4 No windy | Check the F Fan motor 4 | Check the air temperatur piled’ Status SVC Action Cold Explain to customer Check the Compressor Not cold | “And sealed system -49- 43)(2)(1) No Checking flow Result & SVC Action 6 ‘Check the Fan motor. Rotate fan using your hand, Tee! sicy, change the motor. Point [Result [SVC Aetion (cause of ice or rust inside of motor). Motor | Sticry | Change the motor 7 Check the F Fan motor voltage. Point | Result | SVC Action (1)~ (2) | Below 12V | Change the PCB (1) ~ 3) Oor5V | Change the motor

You might also like