Application Note

Switching Regulator IC Series

Bootstrap Circuit in the Buck Converter

This application note explains the step-up circuit using a bootstrap capacitor. In buck converters, this circuit is used when the high-
side switch is the N-ch MOSFET.

1. Role of the bootstrap circuit in the buck VIN

converter
VIN
The configuration of the circuit in proximity to a buck converter
Elements in the IC
Built-in diode
depends on the polarity of the high-side switch. BOOT

When a P-ch MOSFET is used for the high-side switch, there

High-side switch
Nch MOSFET Bootstrap capacitor
are advantages over using a N-ch MOSFET, such as the
VOUT
capability of driving the switch with input voltage V IN as the gate SW
VIN

voltage, as well as voltage reduction and obtainment of the Low-side switch

Nch MOSFET
maximum duty. On the contrary, the use of a P-ch MOSFET Ground

requires a larger chip area for passing the same current.

The use of an N-ch MOSFET for the high-side switch requires
a gate voltage of VIN + Vth (threshold voltage of the N-ch
MOSFET) or higher. A step-up circuit is required because the Figure 1. Example of a charge-pump-type step-up circuit
gate voltage is higher than VIN. This circuit is configured with an
internal diode and an external bootstrap capacitor (charge pump The voltages on the SW and BOOT pins in the example of
type). The total cost, including the cost of the external bootstrap Figure 1 are described as shown in Figure 2, where Vf is the
capacitor, can be lowered because the chip area can be reduced forward direction voltage of the built-in diode.
compared with the P-ch MOSFET, as mentioned above.

2×VIN
2. Description of the charge pump 2×VIN-Vf

operation
BOOT Voltage
In the charge-pump-type step-up circuit, the essential parts
VIN
include a diode and a capacitor (bootstrap capacitor). The diode VIN-Vf
is often built-in as an element in the IC, and only the bootstrap
SW Voltage
capacitor is connected externally.
Ground
Figure 1 shows an example of an actual circuit.

Figure 2. Voltages of SW and BOOT

© 2018 ROHM Co., Ltd. No. 61AN073E Rev.001

1/4
Nov.2018
Bootstrap Circuit in the Buck Converter Application Note

When the SW voltage is low during the switching operations

BOOT anode VIN
in Figure 2, the electric charge is stored in the capacitor from VIN,
thus resulting in the voltage of VIN - Vf across the capacitor.
High-side
When the SW voltage is high, the BOOT voltage increases up to Nch-MOSFET
2 × VIN - Vf, and the built-in diode maintains the voltage at 2 × VGS
VIN - Vf. Therefore, the BOOT voltage switches between VIN - Vf SW

and 2 × VIN - Vf (Figure 3). When the anode of the diode is obtained from VIN,
the gate voltage of the high-side N-ch MOSFET is
VIN - Vf [V] at maximum. When a high voltage is
applied to VIN and when the VGS rating is exceeded,
· When the SW voltage is low the high-side N-ch MOSFET will be destroyed.
VIN

Given that the VIN voltage > BOOT voltage, internal power
a forward direction current flows in the diode. supply(5V)
When SW = Ground, the BOOT voltage is VIN - Vf [V].

BOOT=VIN-Vf[V] BOOT VIN

anode
VIN-Vf[V]

SW
High-side
Ground Nch-MOSFET

VGS
SW
· When the SW voltage is high
When the anode of the diode is connected to
VIN
an internal power supply of approximately 5 V,
Given that the VIN voltage ≦ the BOOT voltage, the gate voltage of the high-side N-ch MOSFET is
no current flows in the diode. The voltage across
the capacitor is maintained at VIN - Vf [V]. 5 - Vf [V] at maximum. Therefore, the VGS rating of
Therefore, the BOOT voltage is 2 × VIN - Vf [V] when SW = VIN. the N-ch MOSFET will not be exceeded,
BOOT=2×VIN-Vf[V] and the high-side N-ch MOSFET can be protected.
VIN-Vf[V]

SW
Figure 4. Method that considers preventing the VGS rating from
VIN
being exceeded

Figure 3. Charge-pump-type step-up circuit diagram

When this BOOT voltage is used as the gate voltage for the
high-side N-ch MOSFET, you can obtain a voltage between the
gate and the source (VGS) that is sufficient to completely turn ON
the MOSFET.
In this example, the anode of the built-in diode is obtained from
VIN, and the BOOT voltage can increase up to 2 × V IN - Vf as
described in the calculation. It is possible that this BOOT voltage
may exceed the breakdown voltage between the gate and
source of the high-side N-ch MOSFET. Therefore, in designing
products with a high input voltage, an internal power supply of
approximately 5 V is connected to the anode so that the BOOT
voltage is maintained below the breakdown voltage between the
gate and the source (Figure 4).

© 2018 ROHM Co., Ltd. No. 61AN073E Rev.001

2/4
Nov.2018
Bootstrap Circuit in the Buck Converter Application Note

3. Capacitance of the bootstrap capacitor When 16 V is applied to the 1005 size ceramic capacitor, the
For the minimum capacitance of the bootstrap capacitors, actual capacitance falls significantly below the nominal value of
follow the capacitance described in each data sheet. Use a small 0.1 μF. Furthermore, approximately half of the nominal value
ceramic capacitor for the bootstrap capacitors. It is necessary to remains. Although the minimum capacitance of the bootstrap
consider the DC bias characteristics of the ceramic capacitors capacitor varies with each IC, an excessively small capacitance
and to confirm that the actual capacitance corresponds with the may result in an electric charge that is insufficient for gate driving.
capacitance described in the data sheet. The insufficient electric charge may lead to unstable gate driving
The DC bias characteristics refer to the characteristics of and impair the operation.
variation in capacitance due to the DC voltage applied across However, we recommend the use of the minimum capacitor
the ceramic capacitor. Generally, the capacitance tends to that satisfies the minimum capacitance because a larger size will
decrease as the DC voltage increases. Furthermore, the affect the cost. On the contrary, an excessively large
variation in capacitance also depends on the size. capacitance could delay the increase in the voltage across the
Figure 5 shows the examples of DC bias characteristics with capacitor and reduce the voltage for gate driving.
different sizes. The adequate value of the capacitance can be obtained from
the following equations. When the high-side N-ch MOSFET is
ON, the electric charge stored in the bootstrap capacitor is
0.11μ
consumed for the gate driving.

0.10μ
D
QLOSS = QG + IBOOT × (1)
f
0.09μ
Capacitance[F]

QLOSS : Total electric charge consumed

0.08μ
when N − ch MOSFET is ON
1005 size, 0.1 μF
QG : Gate charge and electric charge lost
0.07μ 1608 size, 0.1 μF
in the internal circuit
IBOOT : Current passing from the bootstrap capacitor
0.06μ f: Switching frequency
D: Switching duty
0.05μ
0 4 8 12 16
Here, the relation of the variation in the voltage between BOOT
DC Bias Voltage[V] and SW (ΔVBS), the capacitance of the bootstrap capacitor
(CBOOT), and the QLOSS is expressed as follows.

Figure 5. Examples of DC bias characteristics of ceramic QLOSS

CBOOT ≥ (2)
capacitors ΔVBS

Considering that it is desirable to maintain ΔVBS at 0.1 V or below,

the equation can be described as follows.

QLOSS
CBOOT ≥ (3)
0.1

© 2018 ROHM Co., Ltd. No. 61AN073E Rev.001

3/4
Nov.2018
Bootstrap Circuit in the Buck Converter Application Note

VIN

VIN
Elements
in the IC
IBOOT
BOOT
High-side
Nch MOSFET CBOOT
Level shifter
block HG

SW

Figure 6. Circuit diagram required for CBOOT determination

As an example, a calculation is performed with QG = 10 nC,

IBOOT = 10 nA, D = 0.3, and f = 1 MHz. From Equation (1),

0.3
QLOSS = 10nC + 10nA × ≅ 10nC
1MHz
When this value is substituted in Equation (3),

10nC
CBOOT ≥ = 0.1μF
0.1
Therefore, CBOOT should be 0.1 μF or larger.
However, the capacitances described in the data sheet should
be used because they are designed according to the results
obtained from these equations.

© 2018 ROHM Co., Ltd. No. 61AN073E Rev.001

4/4
Nov.2018
 Notice

Notes
1) The information contained herein is subject to change without notice.

2) Before you use our Products, please contact our sales representative and verify the latest specifica-
tions :

3) Although ROHM is continuously working to improve product reliability and quality, semicon-
ductors can break down and malfunction due to various factors.
Therefore, in order to prevent personal injury or fire arising from failure, please take safety
measures such as complying with the derating characteristics, implementing redundant and
fire prevention designs, and utilizing backups and fail-safe procedures. ROHM shall have no
responsibility for any damages arising out of the use of our Poducts beyond the rating specified by
ROHM.

4) Examples of application circuits, circuit constants and any other information contained herein are
provided only to illustrate the standard usage and operations of the Products. The peripheral
conditions must be taken into account when designing circuits for mass production.

5) The technical information specified herein is intended only to show the typical functions of and
examples of application circuits for the Products. ROHM does not grant you, explicitly or implicitly,
any license to use or exercise intellectual property or other rights held by ROHM or any other
parties. ROHM shall have no responsibility whatsoever for any dispute arising out of the use of
such technical information.

6) The Products specified in this document are not designed to be radiation tolerant.

7) For use of our Products in applications requiring a high degree of reliability (as exemplified
below), please contact and consult with a ROHM representative : transportation equipment (i.e.
cars, ships, trains), primary communication equipment, traffic lights, fire/crime prevention, safety
equipment, medical systems, servers, solar cells, and power transmission systems.

8) Do not use our Products in applications requiring extremely high reliability, such as aerospace
equipment, nuclear power control systems, and submarine repeaters.

9) ROHM shall have no responsibility for any damages or injury arising from non-compliance with
the recommended usage conditions and specifications contained herein.

10) ROHM has used reasonable care to ensurH the accuracy of the information contained in this
document. However, ROHM does not warrants that such information is error-free, and ROHM
shall have no responsibility for any damages arising from any inaccuracy or misprint of such
information.

11) Please use the Products in accordance with any applicable environmental laws and regulations,
such as the RoHS Directive. For more details, including RoHS compatibility, please contact a
ROHM sales office. ROHM shall have no responsibility for any damages or losses resulting
non-compliance with any applicable laws or regulations.

12) When providing our Products and technologies contained in this document to other countries,
you must abide by the procedures and provisions stipulated in all applicable export laws and
regulations, including without limitation the US Export Administration Regulations and the Foreign
Exchange and Foreign Trade Act.

13) This document, in part or in whole, may not be reprinted or reproduced without prior consent of
ROHM.

Thank you for your accessing to ROHM product informations.

More detail product informations and catalogs are available, please contact us.

ROHM Customer Support System

http://www.rohm.com/contact/

ZZZURKPFRP
‹652+0&R/WG$OOULJKWVUHVHUYHG
5%