See discussions, stats, and author profiles for this publication at: https://www.researchgate.

net/publication/267601185

Characterization of microstructure and fracture behavior of GG20 and GG25

cast iron materials used in valves

Conference Paper · May 2012

CITATIONS READS

10 39,691

5 authors, including:

Zeynep Taslicukur Ozturk Seyda Polat

National Defence University Turkish Naval Academy Kocaeli University
27 PUBLICATIONS 166 CITATIONS 62 PUBLICATIONS 276 CITATIONS

SEE PROFILE SEE PROFILE

S. Hakan Atapek Enbiya Türedi

Kocaeli University Kocaeli University
105 PUBLICATIONS 443 CITATIONS 38 PUBLICATIONS 80 CITATIONS

SEE PROFILE SEE PROFILE

All content following this page was uploaded by Enbiya Türedi on 02 February 2015.

The user has requested enhancement of the downloaded file.

 23. - 25. 5. 2012, Brno, Czech Republic, EU

CHARACTERIZATION OF MICROSTRUCTURE AND FRACTURE BEHAVIOR OF GG20 AND

GG25 CAST IRON MATERIALS USED IN VALVES

Zeynep TAŞLIÇUKUR*, Gözde S. ALTUĞ*, Şeyda POLAT**,

Ş. Hakan ATAPEK**, Enbiya TÜREDİ**

*) Gedik University, Faculty of Engineering, Department of Metallurgical and Materials Engineering,

Istanbul-Turkey [email protected] , [email protected]
**) Kocaeli University, Faculty of Engineering, Department of Metallurgical and Materials Engineering,
Kocaeli-Turkey [email protected], [email protected], [email protected]

Abstract
In this study, the microstructural characterization of GG20 and GG25 gray cast iron materials were carried
out and their fracture behavior was examined. These materials are commonly used in high pressure safety
valves. In the first stage of the study, the matrix phases (ferrite/pearlite) were determined in addition to the
morphology and distribution of graphite, using light microscope and scanning electron microscope. Image
analysis was done to obtain the amount of graphite which plays an important role on fracture. In the second
stage, microhardness measurements, tensile tests and Charpy impact tests at room temperature were
performed to determine the mechanical properties of the matrices. In the third stage fractographic analysis
was carried out on the fracture surfaces, using scanning electron microscope to indicate the effects of matrix
phase, loading type and test temperature on the fracture behavior.
Keywords : Gray cast iron, characterization, mechanical properties, fractographic analysis.

1. INTRODUCTION
Gray cast iron is an attractive material used in industrial applications due to its some advantageous
properties such as good castability, corrosion resistance, machinability, low melting point, low cost, and high
damping capacity. It is used widely in the manufacturing of some machine components, disc brake rotors
and hydraulic valves [1-7].
Graphite flakes, which are formed during the solidification process, basically control the mechanical
properties and confer low strength and toughness to the gray cast iron. The microstructure of gray cast iron
is characterized by graphite lamellas dispersed in the ferrous matrix. The amount of graphite and size,
morphology and distribution of graphite lamellas are critical in determining the mechanical behavior [1, 4, 6,
8, 9]. The high damping capacity of gray cast iron, which is considerably greater than that of the steel or
other kinds of cast iron, may be attributed to its flake graphite structure [10].
In this study, the microstructural characterization of GG20 and GG25 cast iron materials used in valves was
carried out. A fractographic analysis was also done to determine fracture behavior of the matrix as function
of ferrite, pearlite and graphite distribution under tensile and impact loading.

2. EXPERIMENTAL STUDY

2.1 Materials
In grey cast iron, which is also known as flake graphite cast iron, most of the carbon is present as flake
graphite. The properties of grey cast iron depend on the distribution, size and amount of graphite flakes, and
 23. - 25. 5. 2012, Brno, Czech Republic, EU

the matrix structure. Tab. 1 shows the standard chemical compositions of cast iron materials used in this
study.
Table 1. The standard chemical compositions of GG20 and GG25 cast iron materials.
Materials C Si Mn S P Fe
GG20 3.20-3.40 2.10-2.30 0.50-0.80 max. 0.12 max. 0.40 balance
GG25 3.00-3.25 1.85-2.10 0.40-0.70 max. 0.12 max. 0.25 balance

2.2 Mechanical tests

In order to determine the mechanical properties of cast iron samples, hardness measurement, tensile and
notched impact tests were carried out. Hardness values of the materials were obtained by macro Vickers
hardness tester as HV10. Tensile and notched impact tests were carried out at room temperature according
to TS 138 EN 10002-1 and TS EN 10045-1 standards, respectively. All the mechanical data obtained are
listed in Tab. 2.
Table 2. The mechanical properties of cast iron materials.
2
Materials Tensile strength, MPa Hardness, HV10 Impact toughness, J/mm
GG20 162 187 7.2
GG25 123 159 7.8

2.3 Metallographic sample preparation and microscopic examinations

All samples for the microstructural characterization were prepared by grinding with 320, 600 and 1000 mesh
size SiC abrasives, respectively and then ground surfaces were polished using 3 μm diamond solution.
Etching was carried out with nital (% 3 HNO3) in order to determine the phases within the matrix. Zeiss
Axiotech 100 light microscope (LM) and Jeol JSM 6060 scanning electron microscope (SEM) were used for
metallographic examinations. SEM was used for fractographic analysis as well.

2.4 Image analysis

Leica QWin software package was used to determine the amount of graphite by means of image analysis.
The average and standard deviation values of this spacing were calculated from at least 60 measurements
on images of etched specimen surfaces.

3. RESULTS

3.1 Microstructural characterization

Figure 1 shows the microstructure of polished and etched cast iron materials. The flakes in dark contrast are
clearly seen in the polished matrices (Fig. 1a and c). The flakes can be broken during grinding due to the
contact with abrasives which are harder and polished microstructures exhibit globular/semi-globular regions
indicating the dropped ones. The matrices of GG20 and GG25 materials have typical pearlitic structure
which is a common phase for grey cast iron family (Fig. 1b and d). Its lamellar structure and amount affect
the mechanical properties of the material. As the distance between the lamellas in the pearlite decreases the
mechanical properties of material increase. An increase in the amount of this phase also causes an increase
in the mechanical properties. The amount of carbon has an important role on the formation of pearlite and
GG20 has a higher carbon concentration giving higher mechanical properties.
 23. - 25. 5. 2012, Brno, Czech Republic, EU

(a) (b)

(c) (d)
Figure 1. As polished (a and c) and etched (b and d) microstructures of cast iron materials; (a and b) GG20,
(c and d) GG25. Both of the materials have flake graphites in pearlitic matrix.

3.2 Graphite distribution

All gray cast irons contain flake graphite dispersed in a silicon-iron matrix. Amount of the graphite, its
distribution in the matrix and length of the flakes directly influence the properties of the iron. The basic
strength and hardness of the iron are provided by the metallic matrix. Graphite has little strength or hardness
and it decreases these properties of the metallic matrix. Image analysis shows that GG20 material has 8.676
% graphite in its matrix and GG25 material has only 7.483 %. Figure 2 shows selected ones for the
measurement. The amount of graphite in GG20 material is higher than GG25 due to the higher carbon
content in its composition.

(a) (b)
Figure 2. The microstructures showing the amount of graphite in (a) GG20 and (b) GG25 materials.
 23. - 25. 5. 2012, Brno, Czech Republic, EU

3.3 Mechanical properties

The microstructure of grey cast iron is characterized by graphite lamellas dispersed into the ferrous matrix.
Foundry practice influences the nucleation and growth of graphite flakes, thus their size and type may
enhance the desired properties. The amount of graphite and size, morphology and distribution of graphite
lamellas are critical in determining the mechanical behavior of grey cast iron [1].
For a given pearlitic matrix, three concepts must be clarified to understand the matrix strengthening. Carbon
is the major element for interstitial strengthening mechanism in ferrous based materials. An increase in the
amount of carbon causes the development of the mechanical properties (hardness, strength, not toughness)
of the matrix. On the other hand, a fully pearlitic matrix can be assumed as a precipitation hardened matrix
having ferrite and cementite phases in lamellar morphology. As it is well known from the principles of
physical metallurgy, the strength of pearlite strongly depends on its interlamellar spacing. As the spacing
decreases the strength (hardness) of the matrix increases.
The mechanical properties of GG20 and GG25 cast iron materials are given in Tab. 2. In fact, all these
concepts simply indicate why the mechanical properties of GG20 cast iron is higher than those of GG25 cast
iron. Higher carbon results in higher hardness and strength in the matrix, however, impact toughness values
indicate the inverse correlation. This is possibly due to the effect of higher graphite amount in GG20 (Fig. 2).

3.4 Fractographic analysis

Hornbogen reported that the mechanical properties and also fracture behavior of grey cast irons have
captured attention due to two points of view; (i) in the case of sufficient toughness some cast irons will
compete successfully with steels and (ii) grey cast irons may serve as model materials due to their
microstructure consisting of metallic matrix with graphite which provides quasi-holes of different sizes, shape
and volume fraction [11]. Bradley et al. studied the fracture behavior of different types of cast irons: namely,
grey, white, ductile, malleable and compacted graphite (vermicular) cast irons and reported that the fracture
behavior and the fracture toughness of mentioned cast irons depend on the graphite morphology as well as
the matrix microstructure [12]. Gonzaga et al. investigated the dependency of mechanical properties on the
pearlite content of ductile irons and concluded that (i) a mixture of ferrite and pearlite or a full pearlitic
microstructure with good mechanical properties can be obtained, (ii) the higher hardness values appear in
the cast iron having 100% pearlite, (iii) pearlite hardens the matrix but elongation is lowered while the tensile
strength is increased as consequence of increasing pearlite [13].
The crack formation and propagation result in failure for a given material under loading. The secondary
phases having microvoids with their matrix are commonly responsible for the crack formation/propagation.
Fig. 3 shows the weak bonding between graphite and pearlitic matrix and there are several microvoids
surrounding the graphite. Bertolino et al. reported that lamellar grey cast iron presents a non-lineal load-
displacement record. This macroscopic behaviour has originated from the complex microstructure of these
materials that are formed by two phases (metallic matrix with distributed graphite lamellaes) that induce a
non-uniform distribution of stresses. The graphite lamellaes act as stress raisers producing self
microcracking, or interface debonding at very low stress levels and plastic deformation in the matrix. As a
consequence, the deformation mode of this type of material containing a crack, notch or defect has to be
characterized by the presence of a damaged region ahead the notch formed by a network of microcracks.
The propagation of a macroscopic crack will result from the coalescence of these microcracks together with
the matrix plastic deformation that surrounds the microcracks [14]. The tensile fracture surfaces of
experimental cast irons are given in Fig. 4 and they exhibit typical cleavage fracture. For a cast iron having
fully pearlitic matrix in addition to graphite, cleavage rupture is the dominant fracture under tensile loading.
The fracture of flake graphite cast iron mainly goes through the graphite matrix interface and the inside of the
graphite [15]. The effect of flake on the decohesion is simply illustrated in Fig. 5. All fracture surfaces in Fig.
5 exhibit cleavage type fracture indicating that there is no significant plastic deformation under loading.
 23. - 25. 5. 2012, Brno, Czech Republic, EU

(a) (b)
Figure 3. The interfaces between graphite and matrix having microvoids; (a) GG20 and (b) GG25 materials.

(a) (b)
Figure 4. Tensile fracture surfaces of (a) GG20 and (b) GG25 materials.

(a) (b)

(c) (d)
Figure 5. Impact fracture surfaces of (a and b) GG20 and (c and d) GG25 materials.
 23. - 25. 5. 2012, Brno, Czech Republic, EU

4. CONCLUSIONS

In this study, the microstructural characterization of GG20 and GG25 gray cast iron materials were carried
out and their fracture behavior was examined. The results are given as follows;
(i) Both GG20 and GG25 cast iron have pearlitic matrix having graphite flakes and image analysis showed
that GG20 material has higher graphite due to higher carbon content.
(ii) Carbon content, interlamellar spacing and also precipitated matrix directly affect the mechanical
properties of a given pearlitic matrix. GG20 cast iron has higher hardness and strength values than that of
GG25 cast iron. However, impact toughness of GG25 material is higher than that of GG20 due to low
amount of the graphite in its matrix. Fractographic analysis showed that cast irons exhibited similar fracture
surfaces after tensile/impact loading. Cleavage rupture is the dominant fracture type and there is no
indication of plastic deformation.

ACKNOWLEDGMENT
The authors wish to acknowledge Gedik Casting & Valve Inc. within the Gedik Group for their support in
mechanical tests.

REFERENCES
[1] COLLINI, L., et al. Microstructure and mechanical properties of pearlitic gray cast iron, Materials Science and
Engineering A, 2008, 488(1-2), 529–539.
[2] AKDEMIR, A., et al. Investigation of the tensile properties of continuous steel wire-reinforced gray cast iron
composite, Materials Science and Engineering A, 2011, 528(10-11), 3897–3904.
[3] BEHNAM, M. M. J., et al. Effect of cooling rate on microstructure and mechanical properties of gray cast iron,
Materials Science and Engineering A, 2010, 528(2), 583–588.
[4] AVCI, A., et al. Mechanical and microstructural properties of low-carbon steel-plate-reinforced gray cast iron,
Journal of Materials Processing Technology, 2009, 209(3), 1410-1416.
[5] IPEK, R., et al. An evaluation of the possibilities of using borided GG25 cast iron instead of chilled GG25 cast
iron (surface properties), Journal of Materials Processing Technology, 2000, 105(1-2), 73-79.
[6] ASLANTAŞ, K., et al. Fracture of a compressor rotor made from grey cast iron, Engineering Failure Analysis,
2004, 11(3), 369-373.
[7] WEI, W., et al. Properties of a gray cast iron with oriented graphite flakes, Journal of Materials Processing
Technology, 2007, 182(1-3), 593–597.
[8] VADIRAJ, A., et al. Studies on mechanical and wear properties of alloyed hypereutectic gray cast irons in the
as-cast pearlitic and austempered conditions, Materials and Design, 2010, 31(2), 951-955.
[9] MOONESAN, M., et al. Effect of alloying elements on thermal shock resistance of gray cast iron, Journal of
Alloys and Compounds, 2012, 520, 226-231.
[10] XIN, Z., et al. Gray cast iron with directional graphite flakes produced by cylinder covered compression process,
Journal of Iron and Steel Research International, 2007, 14(5), 52-55.
[11] HORNBOGEN, E. Fracture toughness and fatigue crack growth of grey cast irons, Journal of Materials Science,
1985, 20, 3897-3905.
[12] BRADLEY, W. L., et al., Fracture and fracture toughness of cast irons, International Materials Reviews, 1990,
35, 129-161.
[13] GONZAGA, R. A., et al., Mechanical properties depency of the pearlite content of ductile irons, Journal of
Achievements in Materials and Manufacturing Engineering, 2009, 33, 150-158.
[14] BERTOLINO, G., et al., Geometrical effects on lamellar grey cast iron fracture toughness, Journal of Materials
Processing Technology, 2006, 179, 202-206.
[15] NAKAE, H., et al. Influence of graphite morphology fractured surface in flake graphite cast iron measured by
laser roughness meter, Journal of Japan Foundry Engineerig Society, 2002, 74, 644-649.

View publication stats