Scribd
Upload
23 views3 pages

SKF 68X100X10 CRW1 R Specs

CRW1 radial shaft seals are designed for oil or grease lubrication between rotating and stationary machine components. They feature a metal case, nitrile rubber WAVE lip for reduced heat generation and higher pumping rate, and a garter spring. Most also have a sealant coating on the outer diameter. This particular CRW1 seal is 68mm in shaft diameter, 100mm in housing bore diameter, and 10mm wide.

Uploaded by

Muhammad Wajid
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
23 views3 pages

SKF 68X100X10 CRW1 R Specs

CRW1 radial shaft seals are designed for oil or grease lubrication between rotating and stationary machine components. They feature a metal case, nitrile rubber WAVE lip for reduced heat generation and higher pumping rate, and a garter spring. Most also have a sealant coating on the outer diameter. This particular CRW1 seal is 68mm in shaft diameter, 100mm in housing bore diameter, and 10mm wide.

Uploaded by

Muhammad Wajid
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

68X100X10 CRW1 R

Radial shaft seals are used between rotating and stationary machine
components, or between components in relative motion. CRW1 seals are
designed with a metal case, an SKF WAVE lip made of elastomer with
higher pumping rate to reduce heat generation, and a garter spring to
optimize sealing against the shaft. Most of the seals feature the SKF Bore
Tite coating on the outside diameter that helps fill small imperfections in
the housing bore.
• For oil or grease
• With garter spring
• WAVE lip creates higher pumping rate
• WAVE lip has less friction between shaft and lip
• WAVE lip has a lower temperature at the contact point

Overview

Dimensions

Shaft diameter 68 mm

Housing bore diameter 100 mm

Seal width 10 mm

Performance Properties

Maximum operating temperature 100 °C Design CRW1

Minimum operating temperature -40 °C Auxiliary lip No

Permissible circumferential speed 9 m/s Sealing lip Nitrile rubber (NBR)


material
Rotational speed 2 580 r/min
Type of outside Metal-cased with sealant coating on
diameter the outside diameter

Unit system Metric

Generated from www.skf.com on 2024-01-15 Page 1 of 3


Technical Specification

Type of outside diameter Metal-cased with sealant coating on the outside diameter

Lip material Nitrile rubber (NBR)

Seal design CRW1

Dimensions

d1 68 mm Shaft diameter

D 100 mm Housing bore diameter

b 10 mm Seal width

Application and operating conditions

Operating temperature min. -40 °C

Operating temperature max. 100 °C

Circumferential speed max. 9 m/s

Rotational speed max. 2 580 r/min

Pressure differential 0.07 N/mm²

Associated products

SKF Speedi-Sleeve 99266

Generated from www.skf.com on 2024-01-15 Page 2 of 3


Terms and conditions
By accessing and using this website / app owned and published by AB SKF (publ.)
(556007-3495 · Gothenburg) (“SKF”), you agree to the following terms and conditions:

Warranty Disclaimer and Limitation of Liability


Although every care has been taken to assure the accuracy of the information on this website / app, SKF
provides this information "AS IS" and DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT
NOT LIMITED TO, IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. You acknowledge that your use of this website / app is at your sole risk, that you assume full
responsibility for all costs associated with use of this website / app, and that SKF shall not be liable for any
direct, incidental, consequential, or indirect damages of any kind arising out of your access to, or use of the
information or software made available on this website / app. Any warranties and representations in this
website / app for SKF products or services that you purchase or use will be subject to the agreed upon terms
and conditions in the contract for such product or service. Further, for non-SKF websites / apps that are
referenced in our website / app or where a hyperlink appears, SKF makes no warranties concerning the
accuracy or reliability of the information in these websites / apps and assumes no responsibility for material
created or published by third parties contained therein. In addition, SKF does not warrant that this website /
app or these other linked websites / apps are free from viruses or other harmful elements.

Third Party Services


When viewing YouTube content via the SKF website(s) (i.e. using YouTube API Services), you agree to be
bound by the YouTube Terms of Service.

Copyright
Copyright in this website / app copyright of the information and software made available on this website /
app rest with SKF or its licensors. All rights are reserved. All licensed material will reference the licensor that
has granted SKF the right to use the material. The information and software made available on this website /
app may not be reproduced, duplicated, copied, transferred, distributed, stored, modified, downloaded or
otherwise exploited for any commercial use without the prior written approval of SKF. However, it may be
reproduced, stored and downloaded for use by individuals without prior written approval of SKF. Under no
circumstances may this information or software be supplied to third parties.
This website /app includes certain images used under license from Shutterstock, Inc.

Trademarks and Patents


All trademarks, brand names, and corporate logos displayed on the website / app are the property of SKF or
its licensors, and may not be used in any way without prior written approval by SKF. All licensed trademarks
published on this website / app reference the licensor that has granted SKF the right to use the trademark.
Access to this website / app does not grant to the user any license under any patents owned by or licensed to
SKF.

Changes
SKF reserves the right to make changes or additions to this website / app at any time.

Generated from www.skf.com on 2024-01-15 Page 3 of 3

You might also like