Module- 6

Date- 15/12/23
[email protected]
Switch account

Your email will be recorded when you submit

this form

* Indicates required question

Module- 6
Date-

A self aligning bearing is a. * 1 point

angular bearing.

precision bearing.

radial bearing.

Loads on tapered roller bearings * 1 point

are.

thrust only.

radial only.

radial and thrust.

The metal which must not be * 1 point

heated in a salt bath is.

magnesium alloy.

duralumin.

rivets made of alclad

A gas or fluid line marked with the * 1 point

letters PHDAN.

is a high pressure line. The letters mean

Pressure High, Discharge at Nacelle.

is carrying a substance which may be

dangerous to personnel.

is carrying a substance which cannot be

made non-toxic.

What is fatigue?. * 1 point

Cyclic stressing of a part.

Failure of a component due to

corrosion.

Constant stressing of a part

In four digit aluminum index * 1 point

system number 2024, the first digit

indicates

Number of different major alloying

elements used in the metal

The major alloying element

The percent of alloying metal added

Chromium added to plain carbon * 1 point

steel.

increases it's resistance to corrosion.

turns it into a non-ferrous alloy.

makes the metal softer.

A watermark on a bearing * 1 point

indicates.

bearing running dry.

intergranular corrosion.

lack of lubrication

Flexible lines must be fitted with a * 1 point

slack.

of 5 - 8 % of the length

of at least 10 - 12 % of the length

to allow maximum Kexing during

operation.

Following is the self locking nut? * 1 point

Castle nut

Elastic stop nut

Check nut

A bolt which has X inside a * 1 point

triangle on the head is classified

as an

NAS standard aircraft bolts

NAS close tolerance bolts

AN corrosion resistance steel bolts

A pipe carrying lubricant would be * 1 point

identified by the colour.

white.

yellow.

white and yellow.

Low pressure hoses can withstand * 1 point

the pressure upto

200psi

250psi

350psi

How is the diameter of a cable * 1 point

measured?.

Diameter of one wire multiplied by the

number of wires

Overall diameter.

Diameter of one wire only.

MIL-H-5606 hydraulic fluid O-rings * 1 point

are identified with a.

blue dot.

yellow dot.

yellow and white dot.

A butyl rubber seal is made * 1 point

from.

silicon rubber.

synthetic rubber.

latex natural rubber.

The teeth on the smaller wheel of * 1 point

a bevel gear are called the.

heel.

toe.

foot.

The formation of steel depends * 1 point

upon.

the formation of pearlite into austenite.

the formation of austenite into pearlite.

the presence of pearlite in the structure.

Recessed trangle on the head * 1 point

indicates?

Internal wrenching bolt

Close tolerance bolt

Special l bolt

The oxide film on the surface of * 1 point

aluminium is.

hard and porous.

porous.

non porous.

What is a Rockwell tester used * 1 point

for?.

Hardness Testing.

Tensile Testing.

Fatigue Testing.

Tension regulators on aeroplanes * 1 point

with fully metal bodies are used

to.

set up the necessary tension.

maintain the necessary tension

relax the tension in cold conditions.

What temperature would steel be * 1 point

tempered at?

At the annealing temperature.

Above the annealing temperature.

Below the annealing temperature.

Turnbuckles, depending on type, * 1 point

are locked by.

stiffnuts.

locknuts and wire.

castleated nuts and splitpins

What material would be used * 1 point

where a high temperature

application is required, e.g. a
firewall?.

Aramid (Kevlar) Vbres

Carbon/graphite Vbres.

Ceramic Vbres.

The purpose of castle nut is. * 1 point

For engagement of torque wrench

For safe tying of bolt

Check nut

Gap between two mating gear is * 1 point

called

Clearance

Tolerance

Backlash

To install a flareless coupling. * 1 point

turn until torque is felt plus 3 Kats (half

turn).

hand tight plus 2 Kats

turn until torque is felt plus 2 Kats.

The core material of Alclad is * 1 point

Heat treated aluminum alloy, and the

surface material is commercially pure
aluminum

Commerically pure aluminum and the

surface material is heat treated
aluminum alloy

Strain hardened aluminum alloy and the

surface material is commercialiiy pure
aluminum

A thermoplastic can be. * 1 point

heated and formed only once.

is not affected by even low

temperatures.

can be reheated and reformed more

than once.

Page 2 of 2

Back Submit Clear form

Never submit passwords through Google Forms.

This content is neither created nor endorsed by Google.

Report Abuse - Terms of Service - Privacy Policy

Forms