DCL-10

Standard Installation Type Direct Installation Type

Valve Type
 Part-Turn
Damper
0~90°
Torque/Time
100Nm/30S
Optional
50Nm/15S
100Nm/60S
Duty Type
Open-Close
Modulating
Supply Voltage
DC24V
AC24V
AC110V
AC220V
AC380V
Input/Output Signal
4~20mA
0~10V
Contact
Modbus-RTU | CAN | Ethernet
Options
Over torque protection
Failure Safe
Dehumidification
Diagnosis
Parameters
Power Supply DC24V, AC24V, AC110V, AC220V, AC380V
Standard Torque/Time 100Nm/30S
Optional Torque/Time 50Nm/15S, 100Nm/60S
Rotation angle range 0~90° Configurable
Motor Power/Current DC24V：25W/2.03A
AC24V：25W/2.12A
AC110V：25W/0.57A
AC220V：25W/0.35A
AC380V：15W/0.10A
Control Circuit A/B/C/D/E/F/G/H
Weight 4.5Kg
Insulation Resistance DC24V/AC24V： 100MΩ/250VDC
AC110V/AC220V/AC380V： 100MΩ/500VDC
Withstand Voltage DC24V/AC24V： 500VAC 1 Minite
AC110V/AC220V：1500VAC 1 Minite
AC380V：1800VAC 1 Minite
Water Proof Level IP67
Installation At any angle position
Electrical Interface G1/2 waterproof cable connect: one for power and one for signal
Working Temperature -25℃ ~ +55℃
Optional Function Over Torque Protect, Dehumidification Heater, Convex Indicator, Manual Wheel
Servo Parameters
Input Signal 4~20mA, 0~10V Configurable
Output Signal 4~20mA, 0~10V Configurable
Bus 485/Modbus/CAN
IOT WIFI/LoRA/4G
Basic Error ≤±1%
Return Error ≤1%
Hysteresis 0.5% to 5.0% Configurable
Repositioning Times 0 Times
Repeatability Error ≤1%
Control Circuit
Modulating
E-type: with Servo Module (Positioning)

Input: 4-20mA/0-10V, configurable.

Output: 4-20mA/0-10V, with any
configuration.
Bus:Modbus | CAN
Internet of Things：WIFI | LoRA | 4G.
Wiring instructions:
• Connect to power N line
• Connect to power L line
• 4-20mA or 2-10V input signal
for control actuator position
• 4-20mA or 2-10V output signal
which is propotional with
actuator position
 Open-Close
Type A: With limit position switch (active)

Implement "on" and "off" operations through

switch circuits, and output fully open and
fully closed active signals.

Wiring instructions:
• P1 connect to N
• When P2 connected to L, Actuator
move to Shut
• When P3 connected to L, Actuator
move to Open
• P4 drives shut LED on, when actuator
arrived at shut position while P2
connected to L
• P5 drives shut LED on, when actuator
arrived at open position while P3
connected to L
• P7 connect to earth

Type B: With intermediate position

Switch (passive)

Implement "on" and "off" operations through

switch circuits, and output fully open and fully
closed passive signals.
Wiring instructions:
• P1 connect to N
• When P2 connected to L, Actuator move
to Shut
• When P3 connected to L, Actuator move
to Open
• P4 is common pin for signal output
• P5 connect to com when actuator arrived
at open position
• P6 connect to com when actuator arrived
at shut position
• P7 connect to earth
Type G: DC control circuit with passive contact switch

According to the unidirectional conductivity of the

diode, by commuting the positive and negative
electrodes of the DC power supply, the “on” and
“off” operations are realized and a set of fully on
and fully off passive signals are output.

Wiring instructions:
• P1 connect to + while P2 connect to -,
actuator move to shut
• P2 connect to + while P1 connect to -,
actuator move to open
• P3 is common pin for signal output
• P4 connect to com when actuator arrived at
open position
• P5 connect to com when actuator arrived at
shut position
• P7 connect to earth

H-type: three-phase AC control circuit with passive contact switch

Through external phase inversion circuit, the
motor is turned forward and backward to achieve
"on" and "off" operations and output a set of fully
open and fully closed passive signals

Wiring instructions:
• P1/P2/P3 connect to power L1/L2/L3
• P4 is common pin for external control
• P5 controls shut operation
• P6 controls open operation
• P7 is common pin for signal output
• P8 connect to com when actuator arrived
at open position
• P9 connect to com when actuator arrived
at shut position
• P12 connect to earth
 Position Transmitter
Type C: with 1K Ω (or 500 Ω) potentiometer
Implement "on" and "off" operations through switch
circuits, and output resistance signals corresponding to
the opening position.

Wiring instructions:
• P1 connect to N
• When P2 connected to L, Actuator move to Shut
• When P3 connected to L, Actuator move to Open
• P4 is the negtive of the potentiometer. When
actuator move to open, the resistance between
P4 and P5 increases along with position change
• P5 is output signal of potentiometer
• P6 is the positive of the potentiometer. When
actuator move to open, the resistance between
P6 and P5 decreases along with position change
• P7 connect to earth

Type D: with potentiometer and passive contact position switch

Implement "on" and "off" operations through the switch
circuit, and output resistance signals corresponding to the
opening position, while outputting a set of fully open and
fully closed passive signals.

Wiring instructions:
• P1 connect to N
• When P2 connected to L, Actuator move to Shut
• When P3 connected to L, Actuator move to Open
• P4 is common pin for signal output
• P5 connect to com when actuator arrived at open
position
• P6 connect to com when actuator arrived at shut
position
• P7 is the negtive of the potentiometer. When actuator
move to open, the resistance between P7 and P8
increases along with position change
• P8 is output signal of potentiometer
• P9 is the negtive of the potentiometer. When actuator
move to open, the resistance between P9 and P8
decreases along with position change
• P12 connect to earth
Type F: with position transmitter

Implement "on" and "off" operations through

switch circuits, and output fully open and fully
closed active signals.

Wiring instructions:
• Connect to power N line
• Connect to power L line
• Connect shut to L, actuator move to shut
• Connect open to L, actuator move to open
• Signal output 4-20mA, which is propotional
with actuator position