MASSACHUSETTS INSTITUTE OF TECHNOLOGY

2.710 Optics Spring ’09

Problem Set #3 Posted Feb. 23, 2009 — Due Wednesday, March 4, 2009

1. Wanda’s world Your goldfish Wanda happens to be situated at the center of

her spherical waterworld. At the same time, your friend Olive happens to have
her gaze aligned with Wanda’s. If Olive is located a distance s from the edge of
the sphere, the sphere radius is R, and the refractive index of water is n, then
answer the following questions about Olive and Wanda’s mutual perception of
each other.

000000000
111111111
000000000
111111111 s s’ = R
1111111
0000000
000000000
111111111
0000000
1111111
0000000
1111111
0000000
1111111
0000000
1111111 11111111
00000000
00000000
11111111
0000000
1111111
0000000
1111111
00000000
11111111
00000000
11111111
00000000
11111111
0000000
1111111
0000000
1111111 00000
11111
0000000 11111
1111111 00000
0000000 11111
1111111 00000 R

a) How does Wanda look like to Olive? That is, where is Wanda’s image
formed, what is the magnification, and is the image real or virtual?

b) How does Olive look like to Wanda? That is, where is Olive’s image formed,
what is the magnification, and is the image real or virtual?

c) The data given to you seem to neglect the presence of the glass sphere that
contains the water. Discuss the conditions that this negligence is justified
under.

2. Ball lens magnifier We intend to use a spherical ball lens of radius R and
refractive index n as magnifier in an imaging system, as shown in the schematic
(next page). The refractive index satisfies the relationship 1 < n < 4/3, and the
medium surrounding the ball lens is air (refractive index = 1).

a) Calculate the effective focal length (EFL) of the ball lens. Use the thick lens
model with appropriate parameters.

b) Locate the back focal length (BFL), the front focal length (FFL) and the
principal planes of the ball lens.
 Ball−lens

object
R

c) An object located at distance d to the left of the back surface of the ball
lens, as shown in the schematic, where
4 −�3n
d=R
4(n −�1)

Show that the object is one half (EFL) behind the principal plane, and use
this fact to find the location of the image plane.

d) Is the image real or virtual? Is it erect or inverted? What is the magnifica­

tion?

e) Locate the aperture stop and calculate the numerical aperture (NA) of the
ball lens magnifier optical system.

f ) Sketch how a human obeserver using the optical system of Figure 4 as input
to her eye would form the final image of the object on her retina.

3. Telephoto lens design Consider the telephoto lens system shown below. Lens
L1 has known focal length f , and lens L2 has unknown focal length f0 . The
distance d between the two lenses is also unknown. Specify the telephoto system
according to the following requirements:

L1 L2
f f0
!

d
3f

2
 i) An object at infinity, placed off–axis at angular deviation α = 10−2 radians
must produce a real image of size h = 5 ×�10−2 f (cm).

ii) The real image specified in part (i) must be located at a distance 3f from
L1.

Given the above requirements, design and verify the telephoto lens as follows:

3.a) Specify the two unknowns f0 , d in terms of f .

3.b) Locate the principal planes.

3.c) What is the effective focal length (EFL)?

3.d) If an object is 24f to the left of lens L1, where is the image plane and what
is the magnification? Is the image real or virtual, erect or inverted?

4. Microscope design The optical instrument shown below, consisting of lenses

L1, L3 and stop S2, is intended for direct viewing by human observers, with the
observer’s eye located to the right of L3. The symbols {f1 , a1 }, {f3 , a3 }�
denote
the focal lengths and radii of L1, L3, respectively, and a2 is the radius of S2. All
distance units are in millimeters, and the schematic is not drawn to scale.

S2
L3
L1
object

f1=10 f3=20
a 2=16
so a 1=5 170 20 a 3=1

4.a) Determine the object distance so so that a human observer’s unaccommo­

dated eye may focus the image on the observer’s retina.

4.b) What is the best way to use this instrument? Based on your answer, define
the instrument’s magnifying power (MP) appropriately, and calculate the
MP according to your definition.

3
4.c) Locate the aperture stop, the entrance and exit pupils, and the field stop.
What is the maximum lateral size of an object that can be imaged by this
instrument?

4.d) Where should the observer’s eye be located for optimum viewing by this
instrument? Would that optimum location change if L1 were to be “stopped
up” so that its radius became a1 = 10? Explain why and argue that the
latter instrument (i.e., with a1 = 10) is not practical.

4
MIT OpenCourseWare
http://ocw.mit.edu

2.71 / 2.710 Optics

Spring 2009

For information about citing these materials or our Terms of Use, visit: http://ocw.mit.edu/terms.