Introduction of HNC-8 series products

IPC-200 163

40
5
4.
直径
43
24
5

Significantly enhance processing speed and

IPC200技术规格

CPU

105
performance execution efficiency
109
50

95

upgrade
铭牌

Disk capacity Standard 8G eMMC SSD, mSATA interfaces

increase reserved
Standard 1000Mbps Gigabit Ethernet port
Improved
175 4
network port
and an Ethercat bus communication port,
183
performance support Ethercat protocol third-party servo,
I/O
USB transfer The USB is upgraded to two USB3.0 ports,
performance and the file transfer rate is greatly improved.
Aluminum profile box structure, hard
Structure
improvement anodized treatment, large area fin-shaped
aluminum profile heat dissipation, no fan.
 Introduction of HNC-8 series products

IPC-200
 Support EtherCAT+NCUC EtherCAT interface NCUC interface
 Optional EtherCAT+M3 (Optional M3 interface)
 The M3 interface is in the form of
a network port
Support two kinds of
 It is recommended to use IPC-200
and use V2.0 software bus mixed connection
 Introduction of HNC-8 series products
UPS power supply-145U

Rated input voltage: AC 220V±10%,

Input power 145U 技术规格
Frequency: 47-63Hz Rated power: 145W
Rated output voltage: DC +24V, six outputs,
two of which have UPS function and power
Output power
failure detection signal output, total rated
output current: 6A
UPS 30s (1A load)
discharge time
Overload protection: allow the rated output
power
105% -150%, overload protection mode:
protect turn off the output, restore after restart
Over-voltage protection: allow the output
voltage 23.5-27V, overload protection mode:
turn off the output, restore after restart
Introduction of HNC-8 series products
 Introduction of HNC-8 series products
HIO-1000（Combined IO unit ）
Sub-module
Submodule name instruction
model
Provide 1 communication sub-module and 8 functional sub-
9-slot backplane sub-module HIO-1009
module slots
Provide 1 communication sub-module and 5 functional sub-
Bottom 6-slot backplane sub-module HIO-1006
module slots
plate
NCUC protocol
Required (under optical fiber interface communication mode);
communication sub-module HIO-1063
Supported system: HNC- 8
(SC optical fiber interface) 220输入 开关电源 24V GND

Optional, each sub-module provides 2 axis control interfaces

Axis Incremental pulse axis control
HIO-1041 Each interface includes: pulse command; D/A analog220V voltage
control sub-module
command; encoder feedback command PNP
Optional, each sub-module provides 4 analog inputs and 4 analog 输入 继电器
Analog Analog i/o submodule HIO-1073 板接 24V GND

outputs NPN
线法
输入
HIO-1075 板接
Optional, each sub-module provides 6 analog inputs, can UPS
measure
Temperatu (PC100) 线法
Analog input 6 temperatures, and the system supports a maximum of开30
re board HIO-1076
temperature measurements 关
(KTY84) 电
源 NPN
NPN type switch input sub- Optional, each sub-module provides 16-channel NPN PLC switch
145
HIO-1011N 输出
module input signal interface, low-level effective U 板接
PNP type switch input sub- 线法
Optional, each sub-module provides 16 channels of PNP PLC
module HIO-1011P
switch input signal interface, high level effective
Switch
Optional, each sub-module provides 16-channel NPN PLC switch
NPN switch output sub-module HIO-1021N
output signal interface, low-level effective
此部份为通
Optional, each sub-module provides 24 inputs (each 8 channels 讯子模块工
Switch input and output
HIO-1031 of NPN and PNP can be optional through common end jumpers) 作电源
module 此部份为PLC电路电源
16 outputs, low level active
Introduction of HNC-8 series products

Function Description:
1. If the COM0 port is connected to GND, you can configure Xm+0.0~ Xm+0.7 as PNP
input. If the COM0 port is connected to 24V, Xm+0.0~Xm+0.7 can be configured as
NPN input. Similarly, COM1 and COM2 can be configured corresponding to
Xm+1.0~Xm+1.7, Xm+2.0~Xm+2.7 are PNP type input or NPN type input.
2. It is valid if the current flowing through the input port is greater than 6mA.
Precautions:
1.The three groups of inputs of this module occupy four groups of input points in the
system, each group has 8 bits, and the last group is reserved by default. Two sets of
output occupied
2. If the input configuration ports COM0-COM2 are left open, the default is PNP type
input. Two sets of output points of the system.
3. If the input configuration ports COM0-COM2 are left unconnected, the default is
PNP type output
 Introduction of HNC-8 series products

HIO-1200 (independent IO unit)

HIO-1200独立式开关单元规格

Module model instruction

NCUC/Ethercat bus, backplane +

HIO-1200-M1 HIO-1200-K1 terminal board (24
HIO-1200E-M1 inputs, 16 outputs, 1 encoder
feedback interface, 1 DA)
NCUC/Ethercat bus, backplane +
HIO-1200-M2 HIO-1200-31 expansion board (48
HIO-1200E-M2 inputs, 32 outputs, 1 encoder
feedback interface, 1 DA)
Introduction of HNC-8 series products
Introduction of HNC-8 series products
 Introduction of HNC-8 series products
The handheld unit provides
emergency stop button,
enable button, work
indicator light,
coordinate selection (OFF,
X, Y, Z, 4), magnification
selection (X1, X10, X100)
and manual pulse
generator.

The handheld interface

plug is connected to the
handheld control interface
XS8 of the HNC-8 series
numerical control device.
 Introduction of HNC-8 series products

Bus servo drive

Features:
a) HSV-160U low voltage series (220V): 4 specifications: 20A, 30A, 50A, 75A; HSV-180U high voltage
series (380V): 35A, 50A, 75A, 100A, 150A, 200A, 250A, There are 9 specifications of 300A and 450A, and
the maximum power output of the power loop reaches 100KW;
b) Using a unified encoder interface, it can be adapted to composite incremental photoelectric encoders,
all-digital absolute encoders, sine and cosine absolute encoders; support ENDAT2.1/2.2, BISS, HIPERFACE,
Tamagawa and other serial absolute encoders Value encoder communication transmission protocol,
support single-turn/multi-turn absolute position processing;
c) Adopt industrial Ethernet bus interface, support NCUC and EtherCAT two bus data link layer protocols,
realize high-speed data exchange with CNC devices, such as status monitoring, parameter modification,
fault diagnosis and other functions;
d) HSV-180U 160U supports the second encoder interface to achieve full closed-loop control;
e) By integrating different software modules, it can be adapted to servo motors, spindle motors, torque
motors and other types of motors.
 Introduction of HNC-8 series products

HSV-160U series AC servo drive unit

HSV-160U has a high-speed industrial Ethernet bus interface, and adopts the NCUC bus protocol with
independent intellectual property rights to realize high-speed data exchange with numerical control
devices; it has a high-resolution absolute encoder interface, which can be adapted to composite
incremental, sine and cosine , All-digital absolute encoders and other signal types, the position feedback
resolution can reach up to 23 bits.
The HSV-160U AC servo drive unit has four specifications of 20A, 30A, 50A, and 75A, and the maximum power
output of the power loop reaches 5.5KW.
 Introduction of HNC-8 series products

Motor power = motor rated speed * rated torque / 9560

Introduction of HNC-8 series products
Introduction of HNC-8 series products
Introduction of HNC-8 series products
 Introduction of HNC-8 series products
HSV-180U series AC servo drive unit
HSV-180U has a high-speed industrial Ethernet bus interface, and adopts the NCUC bus protocol with independent intellectual
property rights to realize high-speed data exchange with numerical control devices; it has a high-resolution absolute encoder
interface, which can be adapted to composite incremental, sine and cosine , All-digital absolute encoders and other signal types,
the position feedback resolution can reach up to 23 bits. Support dual encoder interface, can realize full closed loop control. The
HSV-180U AC servo drive unit forms a total of eight specifications from 035 to 450, and the maximum power output of the
power loop reaches 75KW, which greatly broadens the power output range of the company's servo drive products.
Introduction of HNC-8 series products
Introduction of HNC-8 series products