HYPERPLAS R

POLYESTER MEMBRANE

Uses to the substrate. The overlaps are to be sealed by

flame torch. Hyperplas Polyester can be topped with
Hyperplas Polyester is normally used in protected topping such as cement screed or tiles on accessible
roofing and waterproofing application in a single roofs with a chicken wire mesh reinforcement.
layer system and also recommended as a base Inaccessible roofs can be topped with a layer of IWL
layer in multilayer system in various application Bitumen & IWL Aluminium Paint.
including damp-proofing.
Roof slabs, Podium slab, basement and Raft slab, Limitation
Roof Garden, Toilet Sunken Slab, Swimming Pool.
Application temperature ranges from 15⁰C to 50⁰C. It
is better to warm the back of the membrane for
Advantages application below 15⁰C and should be stored at above
20⁰C before application to enable easy application and
Excellent resistance to ageing and weathering.
immediate bond to the substrate.
Stability at high temperatures and total
impermeability. Packing
High resistance to impact and puncture.
Fast application and easy. Hyperplas Polyester Membrane: 10 m length X 1 m
width
Coldstick: 20 Kg container
Description
Hyperplas Polyester is a high softening point. APP
Coverage
modified polymeric waterproofing membrane
Coldstick: 3-4 per sq.m/kg on a standard smooth surface
manufactured to highest standards. It consists of a
center core of Spun Bonded Polyester mat for extra
mechanical strength. The center core is protected on
Storage
both sides with Polymeric Asphaltic mix, which has high
All products have a shelf life of 12 months if stored in a
penetration, high heat resistance and high softening
cool, dry store away from sources of heat, in the
point. With high tensile strength, the membrane is still
original unopened packing. It should be stored
extremely flexible and pliable to adapt to contours. For
horizontally, not more than one pallet high.
this reason this membrane makes an ideal
waterproofer. Hyperplas Polyester is also available with Safety measures
dual centre core of a High Molecular High Density
Polyethylene Film. This additional polyethylene core No health hazards with the use of Hyperplas
provides additional security strength. Membrane and Coldstick. If Coldstick Primer is
swallowed, drink a glass of water and do not induce
Surface preparation vomiting. When contacted with eyes occurs flood with
copius amounts of clean water for at least 15 minutes
Smooth surface is required to apply the membrane. and seek medical advice. If contacted with skin wash
The surface is first cleaned to eliminate all sharp the skin thoroughly.
projection.
Fire
Priming
Hyerplas Membrane and Coldstick are flammable. Do
IWL Primer / IWL CS / IWL Blown Bitumen is then not smoke near these products. Coldstick contains
coated on the surface (for more details refer relevant volatile flammable solvents. Use only in open areas,
data sheets). well away from sources of ignition.

Application Specification
Hyperplas Polyester is unrolled over the surface with Hyperplas Polyester is available in grades of 2mm,
torch application (with overlaps of 10cm) and bonded 3mm, 4mm, 3Kg, 3.5Kg or 4Kg/sqm.

1
HYPERPLAS R
POLYESTER MEMBRANE
Technical Support
Requirement
Requirement
Requirement for Mineral
for Method of
S. No. Test for Plain Membrane Unit
Aluminium Test, Ref to
Membrane (including
Membrane
Aluminium)
Thickness of membrane,
(including mineral
±5% or ±5% or ±5% or
1 granules / aluminum foil) mm B-2 of IS 7193
maximum maximum maximum
±0.15mm ±0.15mm ±0.15mm
a) Below 3mm
±5% or ±5% or ±5% or
b) 3mm and above maximum maximum maximum mm B-2 of IS 7193
±0.2mm ±0.2mm ±0.2mm
Does not Does not Does not
Cold flexibility⁰C IS 13826
2 crack crack crack ⁰C
(All thicknesses) (Part 2)
at -2⁰C at -2⁰C at -2⁰C

3 Softening point (All ≥150⁰C ≥150⁰C ≥150⁰C o

C IS 1205
thicknesses)
Tensile strength:
a) Below 3mm:Longitudinal 300 ± 20% 300 ± 20% 300 ± 20% N/5cm IS13826
4
:Transverse 200 ± 20% 200 ± 20% 200 ± 20% @23⁰C (Part 1)

b)3mm&above:Longitudinal 650 ± 20% 650 ± 20% 650 ± 20% N/5cm IS13826

:Transverse 400 ± 20% 400 ± 20% 400 ± 20% @23⁰C (Part 1)
Elongation:
30 ± 20% 20 ± 20% 15 ± 10% IS 13826
a) Below 3mm:Longitudinal
30 ± 20% 20 ± 20% 15 ± 10% (Part 1)
5 :Transverse %
40 ± 15% 30±15% 20 ± 10% IS 13826
b)3mm&above:Longitudinal 35 ± 15% 25±15% 20 ± 10% (Part 1)
:Transverse
Tear Strength:
Not Not Not Not Not
a) Below 3mm:Longitudinal
:Transverse applicable applicable applicable applicable applicable
6
b)3mm&above:Longitudinal 500Min 500Min 500Min B-4 of
N
:Transverse 300Min 300 Min 300 Min IS 7193
Heat resistance IS 13826
7 No Flow No Flow No Flow 120⁰C, 2 hours
(All thickness) (Part 5)
Penetration @ 25⁰C, dmm
8 25 ± 5 25 ± 5 25 ± 5 IS 1203
100g,5s (All thickness) (tenths of mm)
Water absorption IS 13826
9 1, Max Not applicable 1,Max %
(All thicknesses), (Part 6)
Dimension stability
10 longitudinal/transverse ± 0.5 / ± 0.5 ±0.5/±0.5 ±0.5/±0.5 % Measurement
(All thickness)
No sign of No sign of No sign of IS 13826
11 Pressure head test -
leakage leakage leakage (Part 4)
Shall show no Shall show no Shall show no -
Puncture resistance test
12 sign of sign of sign of Annex C
(Optional)
puncture puncture puncture

W-360, North Main Road, Anna Nagar West Extension, Chennai - 600 101
Ph: 044-26156000 / 044-26152100 / 044-26156900 | [email protected] | www.iwl.in 01-2018-A 2