THIS DRAWING IS A COPYRIGHT.

IT IS THE SOLE PROPERTY OF M/S REKAZ ENGINEERING ANY USE OF THIS DRAWING WITHOUT WRITTEN CO- NSENT BY REKAZ ENGINEERING IS STRICTLY PROHIBITED

SNo. NOTES

1. ALL DIMENSIONS ARE IN MILLIMETERS UNLESS

OTHERWISE STATED.
CATEFORY CHART
GENERAL
2. THIS DRAWING IS TO BE READ IN CONJUNCTION WITH
- ALL DIMENSIONS ARE IN MILLIMETERS, SHORING OF EXCAVATION SPECIFICATIONS AND TECHNICAL DRAWINGS.
· TOP BARS ARE THOSE WHICH HAVE 300mm
- USE SHOWN DIMENSIONS. DO NOT SCALE THE OR MORE OF CONCRETE UNDER THEM.
DRAWINGS. REST ARE OTHER BARS.
1. WHERE REQUIRED OR INSTRUCTED BY THE ENGINEER,
3. DO NOT SCALE FROM THE DRAWING WHERE FIGURE
CONTRACTOR SHALL DESIGN AND EXECUTE APPROPRIATE
DIMENSIONS ARE PROVIDED- IF IN DOUBT ASK.
- ALL STRUCTURAL DRAWINGS SHALL BE READ IN · WHEN BARS ARE BUNDLED, INCREASE THE EXCAVATION SHORING SYSTEM SUBJECT TO THE ENGINEER'S
CONJUNCTION WITH RELEVANT ARCHITECTURAL, CIVIL, LAP BY 20% FOR 3 BAR BUNDLE, 33% FOR 4
BAR BUNDLE.
APPROVAL.
MECHANICAL, ELECTRICAL, PLUMBING AND LANDSCAPE
DRAWINGS.
4.
· MINIMUM DEVELOPMENT SHALL BE 300. COMPACTED STRUCTURAL FILL ALL LEVELS AND DIMENSIONS SHALL BE CHECKED AT THE
- ANY DISCREPANCY NOTED SHALL BE BROUGHT TO THE SITE PRIOR TO CONSTRUCTION AND DISCREPANCIES IF
· MINIMUM SPLICE FOR WELDED FABRIC ANY TO BE NOTIFIED TO REKAZ ENGINEERING
NOTICE OF THE ENGINEER BEFORE COMMENCING THE
WORK.
SHALL BE 200mm. 1. PROVIDE FILL FREE OF ORGANIC MATERIALS, DEBRIS AND CLAY.
· MINIMUM DEVELOPMENT LENGTH IN
- CONTRACTOR SHALL VERIFY LOCATIONS OF EMBEDDED COMPRESSION SHALL BE 200. 2. PLACE FILL IN LIFTS NOT EXCEEDING 200MM. 5. THIS DRAWING IS A COPYRIGHT. IT IS THE SOLE
ITEMS PRIOR TO CASTING OF CONCRETE.
PROPERTY OF REKAZ ENGINEERING SERVICES
· SPLICE LENGTH RATIO (Ld/db) IN 3. COMPACT FILL TO 95 PERCENT PROCTOR DENSITY AT ANY USE OF THIS DRAWING WITHOUT WRITTEN
COMPRESSION = 30 AND SHALL NOT BE CO- NSENT BY REKAZ ENGINEERING SERVICES IS
DESIGN CRITERIA LESS THAN 300mm. OPTIMUM MOISTURE CONTENT AS VERIFIED BY ASTM D 1557.
STRICTLY PROHIBITED
WHERE USED BELOW FOOTINGS AND MATS, THE BEARING
CONCRETE COVER FOR REINFORCEMENT CAPACITY OF THE FILL SHALL BE 250 KN/M2 MIN.
- THE REINFORCED CONCRETE DESIGN IS BASED ON
6. ALL EXTERNAL WALLS,VOIDS,COLUMNS, BEAMS AND
ACI-318-02 AND OTHER RELEVANT ACI CODES.
1. CONCRETE CAST AGAINST AND
PERMANENTLY EXPOSED TO EARTH. 75
BLOCK WALLS SHAFTS TO BE INSULATED
- LIVE LOADS ARE BASED ON ASCE 7-02.
2. CONCRETE EXPOSED TO EARTH OR WEATHER 1. ALL BLOCK WALLS ARE OF LIGHT WEIGHT BLOCKS WITH
Y18 AND MORE 50
MAXIMUM DENSITY OF 7.8KN./M3
Y16 AND LESS 40
CONCRETE
- STRUCTURAL CONCRETE CYLINDRICAL
3. CONCRETE NOR EXPOSED TO WEATHER 2. FREESTANDING BLOCK WALLS, WITH LENGTH BETWEE LATERAL REV. DATE DESCRIPTION DRAWN CHECKED
OR IN CONTACT EITHER EARTH
CRUSHING STRENGTH AT 28 DAYS (fc') SUPPORTS EXCEEDING 36X WALL THICKNESS FOR INTERNAL OR
SHALL BE AS FOLLOWS : SLABS, WALLS, JOISTS FOR Y 35 AND LESS 30 18x WALL THICKNESS FOR EXTERNAL SHALL BE TREATED
BEAMS, COLOUMS ACCORDING TO 7.8.3.1 & 7.8.3.2, CONTRACTOR SHALL SUBMIT THE
- 30mtr. FOUNDATION AND GRADE BEAMS, COLUMNS,
SLABS ETC...
STRUCTURAL DESIGN OF THE PILASTERS TO THE ENGINEER FOR
PRIMARY REINFORCEMENT, TIES, STIRRUPS 40
SPIRALS APPROVAL.
- ALL CONCRETE WORK SHALL HAVE NORMAL CEMENT
ASST. C150 TYPE-1 EXCEPT THOSE IN CONTACT WITH 3. FREESTANDING WALLS SHALL SPAN BETWEEN PILASTERS
SOIL SHALL BE ACCORDING TO 3.3, 3.4 & 3.5.
SOIL DATA : FOUNDATION HAVE BOON DESIGNED SPACED AND DESIGNED TO PROVIDE ADEQUATE STABILITY
- CONCRETE IN CONTACT WITH SOIL SHALL USE SRC FOR SAFE BEARING CAPACITY OF 250 KN/M2 FOR THE BLOCK WALL
CONTRACTOR IS TO ENSURE ATTAINMENT OF
CEMENT CONFORMING TO ASST. STANDARDS.
SAFE BEARING CAPACITY PRIOR TO PROCEEDING
WITH CONSTRUCTIONS OTHERWISE CONTACT THE 4. THE PILASTERS CAN BE OF CONCRETE, HOLLOW BLOCK REINFORCED
- CEMENT CONTENT SHALL BE 320KG/M3 MINIMUM TO ENGINEER FOR INTRUCTION. PROPERLY TO THE STRUCTURE.
400KG/M3 MAXIMUM.

- MAXIMUM WATER CEMENT RATIO SHALL BE 0.40. MISCELLANEOUS 5. THE BLOCK WALLS SHALL BE PROVIDED WITH HORIZONTAL JOINT
REINFORCEMENT, ACCORDING TO ACI 530-99 AND THE
- ALL PLAIN AND MASS CONCRETE SHALL HAVE A CONSTRUCTION JOINTS
CYLINDRICAL CRUSHING STRENGTH OF 15 MPA AT
SPECIFICATIONS, ACHORED TO THE PILASTERS.
28 DAYS - CONSTRUCTION JOINTS IF REQUIRED SHALL BE PROVIDED IN

- LIGHT WEIGHT CONCRETE SHALL HAVE A MAXIMUM

FOUNDATION, RETAINING WALLS, SLABS, BEAMS ETC. AS PER
DETAILS AND STRUCTURAL SPECIFICATIONS.
Abbreviations
DENSITY OF 600KG/M3 AND CYLINDRICAL CRUSHING
STRENGTH OF 4 MPA AT 28 DAYS, UNLESS OTHERWISE - CONSTRUCTION JOINTS SHALL BE LOCATED AT:
NOTED.
C.I.P. = cast - in - place concrete
C.J. = control joint/ construction joint
- MAXIMUM SIZE OF AGGREGATE SHALL BE 20mm. - ON ANY VERTICAL PLANE FOR RETAINING WALLS.
INFLECTION POINT OF SPANS FOR BEAMS AND SLABS HAVING NO C.M.U. = concrete masonry unit
- 100MM THICK BLINDING SHALL BE PROVIDED UNDER POINT LOADS AT CENTER OF SPAN. CONTR = contractor
- A MINIMUM DISTANCE OF TWO TIMES THE WIDTH OF INTERSECTING
FOUNDATIONS AND SHALL EXTEND 100MM BEYOND THE
BEAMS. (APPLICABLE TO GIRDERS ONLY). D.B.A. = deformed bar anchor
FOUNDATIONS. 50MM THICK BLINDING SHALL BE
PROVIDED UNDER TIE BEAMS E.F. = each face
- LOCATION OF CONSTRUCTION JOINTS OTHER THAN THOSE
MENTIONED SHAL HAVE THE PRIOR APPROVAL OF THE
E.J. = expansion joint
- ALL CONCRETE SHALL BE FROM REEDY MIX APPROVED ENGINEER. E.T.C. = elevation top of pile cap

ekaz
SUPPLIERS UNLESS OTHER WISE APPROVED BY THE
ENGINEER. - CONSTRUCTION JOINTS SHALL BE PROPERLY INDICATED ON
E.T.F. = elevation top of footing
SHOP DRAWIGS SUBJECT TO THE APPROVAL OF ENGINEER. E.T.G.B. = elevation top of grade beam
E.T.W. = elevation top of wall engineering
BACK FILLING
E.W. = each way
REINFORCING STEEL - BACKFILLING OF BOUNDARY AND LANDSCAPE WALLS SHALL BE E.W.E.F. = each way, each face
CARRIED OUT SIMULTANEOUSLY OF BOTH SIDES OF THE
1. ALL REINFORCING STEEL SHALL CONFORM TO ASTM F.D. = floor drain
615M HAVING A MINIMUM YIELD STRENGTH OF
420MPa,EXCEPT FOR WELDED REINF. SHALL CONFORM TO
G.C. = general contractor
ASTM 706M HAVING A MINIMUM YEILD STRENGTH OF WATERPROOFING AND WATER STOPS H.A.S. = headed anchor studs
420MPa. L.W. = lightwall
1. SUBSTRUCTURE UNDER SLAB-ON-GRADE SHALL BE
2. ALL WELDED WIRE FABRIC SHALL CONFORM TO ASTM PROTECTED WITH WATERPROOFING MEMBRANE AS N.S.N.S. = non - shrink, non stain
SHOWN UNLESS NOTED REFER SPECIFICATION FOR DETAIL.
A497 HAVING A MINIMUM YIELD STRENGTH OF 420 MPa. O.C. = on center
3. DEVELOPMENT & SPLICE LENGTHS IN TENSION FOR
2. WATER STOPS OF APPROVED MANUFACTURER AND P/C = precast concrete
CONTRACTING SHALL BE PROVIDED IN ALL CONTROL AND
REINFORCING BARS IN SLABS , COLUMNS AND WALLS CONSTRUCTION JOINTS EXPOSED TO WATER. R.D. = roof drain
SHALL S.O.G. = slab on grade
BE AS PER ACI-318 - C2 3. ALL THE WATER RETAINING STRUCTURES, IF ANY SHALL BE
TESTED FOR WATER TIGHTNESS BEFORE BACK FILLING & S.W. = shearwall
02., REFER TABLES BELOW: CLADDING. U.N. = unless noted
IF FOUND NECESSARY THE REMEDIAL MEASURES SHALL
BE U.N.O. = unless noted otherwise
NOTES : 1. SEE CATEGORY CHART FOR CATEGORY I & II. CARRIED OUT WITH WILL INCLUDE FIXING DEFECTS SUCH W.W.R. = welded wire reinforcement
AS.
THIS DRAWING IS A COPYRIGHT. IT IS THE SOLE PROPERTY OF M/S REKAZ ENGINEERING ANY USE OF THIS DRAWING WITHOUT WRITTEN CO- NSENT BY REKAZ ENGINEERING IS STRICTLY PROHIBITED

1 2 3 4 5 SNo. NOTES

1. ALL DIMENSIONS ARE IN MILLIMETERS UNLESS

OTHERWISE STATED.

2. THIS DRAWING IS TO BE READ IN CONJUNCTION WITH

GB2
C2 SF3
GB2 C2 GB2
SPECIFICATIONS AND TECHNICAL DRAWINGS.
C2 SF3 GB2
C2 C2 GB2
GB2
SF3 C2 C2 SF3
C2
3. DO NOT SCALE FROM THE DRAWING WHERE FIGURE
EXP. JOINT DIMENSIONS ARE PROVIDED- IF IN DOUBT ASK.

DEEP FOUNDATION

GB2
4. ALL LEVELS AND DIMENSIONS SHALL BE CHECKED AT THE

SF3

GB1
SF1
SITE PRIOR TO CONSTRUCTION AND DISCREPANCIES IF
ANY TO BE NOTIFIED TO REKAZ ENGINEERING

EXP. JOINT
F1 F1
GB1
A C2 A
C1 C1 5. THIS DRAWING IS A COPYRIGHT. IT IS THE SOLE
C2 PROPERTY OF REKAZ ENGINEERING SERVICES
ANY USE OF THIS DRAWING WITHOUT WRITTEN
GB1
B B CO- NSENT BY REKAZ ENGINEERING SERVICES IS
C1 C1 STRICTLY PROHIBITED

GB2
SF1

SF1
SF1

GB1

GB1
SF1
SF1
Swimming pool foundation 6. ALL EXTERNAL WALLS,VOIDS,COLUMNS, BEAMS AND

GB1

GB1
design by the specialist GB1 GB1 SHAFTS TO BE INSULATED
C C

GB1
C2 SF1 SF1 SF1

GB1

GB1

GB1
SF1

SF1
SF1
SF3

SF1 SF1 SF1

GB1 GB1 GB1
D D REV. DATE DESCRIPTION DRAWN CHECKED

SF1
C1 GB1
C1
GB2

F1 F1 C1 C1

C2 DEEP FOUNDATION
TIE BEAM

TIE BEAM
C2
EXP. JOINT

GB1
SF1
SF1
GB1
E E
GB2

C1 C1
SF1 SF1 SF1
SF3

GB1

GB1

GB1
GB1

SF1

SF1

SF1

SF1 SF1 SF1 SF1

C2 GB1 GB1 GB1 C1 GB1 C1
F C1 F
C1
SF1

GB1

GB1
GB1

GB1

SF1
GB2

C1
C1 C1 C1
SF1
GB1

C2
GB1

GB1
G G
SF1

SF1
GB1

DOWELS

ekaz
SF3

SF1 SF1
GB2

C3

SF1
GB1

GB1
SF1

C3
engineering
GB1
GB1

EXP. JOINT
SF1 SF1 SF1 SF1 SF1
GB1 C1 GB1 C1 GB1 C1 GB1 GB1 C1
H H
C2 C2

1 2 3 4 5

FOUNDATION PLAN
SCALE 1:100
THIS DRAWING IS A COPYRIGHT. IT IS THE SOLE PROPERTY OF M/S REKAZ ENGINEERING ANY USE OF THIS DRAWING WITHOUT WRITTEN CO- NSENT BY REKAZ ENGINEERING IS STRICTLY PROHIBITED

SNo. NOTES

1 2 3 4 5 1. ALL DIMENSIONS ARE IN MILLIMETERS UNLESS

OTHERWISE STATED.

2. THIS DRAWING IS TO BE READ IN CONJUNCTION WITH

SPECIFICATIONS AND TECHNICAL DRAWINGS.

3. DO NOT SCALE FROM THE DRAWING WHERE FIGURE

DIMENSIONS ARE PROVIDED- IF IN DOUBT ASK.

4. ALL LEVELS AND DIMENSIONS SHALL BE CHECKED AT THE

SITE PRIOR TO CONSTRUCTION AND DISCREPANCIES IF
ANY TO BE NOTIFIED TO REKAZ ENGINEERING

5. THIS DRAWING IS A COPYRIGHT. IT IS THE SOLE

PROPERTY OF REKAZ ENGINEERING SERVICES
A A ANY USE OF THIS DRAWING WITHOUT WRITTEN

CB1

CB1
CO- NSENT BY REKAZ ENGINEERING SERVICES IS
STRICTLY PROHIBITED

B B
POST TENSION SLAB 6. ALL EXTERNAL WALLS,VOIDS,COLUMNS, BEAMS AND
DESIGN BY SPECIALIST SHAFTS TO BE INSULATED
200 mm THICKNESS

C C

B3

B3
REV. DATE DESCRIPTION DRAWN CHECKED

D D
B2

POST TENSION SLAB SEEN BELOW

DESIGN BY SPECIALIST

B2

B2

B2
200 mm THICKNESS
E E

F B2
F
B2 B2

B2
B2

B2

POST TENSION SLAB

B2

B2
DESIGN BY SPECIALIST
G
STAIR WELL
200 mm THICKNESS G
ekaz engineering
B2
B2

B2
H H

1 2 3 4 5

FIRST FLOOR FRAMING PLAN

SCALE 1:100
THIS DRAWING IS A COPYRIGHT. IT IS THE SOLE PROPERTY OF M/S REKAZ ENGINEERING ANY USE OF THIS DRAWING WITHOUT WRITTEN CO- NSENT BY REKAZ ENGINEERING IS STRICTLY PROHIBITED

SNo. NOTES
1 2 3 4 5 COLUMNS DETAIL 1. ALL DIMENSIONS ARE IN MILLIMETERS UNLESS
OTHERWISE STATED.
500 400
200
2. THIS DRAWING IS TO BE READ IN CONJUNCTION WITH
SPECIFICATIONS AND TECHNICAL DRAWINGS.

200
200

200
3. DO NOT SCALE FROM THE DRAWING WHERE FIGURE
DIMENSIONS ARE PROVIDED- IF IN DOUBT ASK.

C1 C2 C3 4. ALL LEVELS AND DIMENSIONS SHALL BE CHECKED AT THE

SITE PRIOR TO CONSTRUCTION AND DISCREPANCIES IF
ANY TO BE NOTIFIED TO REKAZ ENGINEERING

5. THIS DRAWING IS A COPYRIGHT. IT IS THE SOLE

A A PROPERTY OF REKAZ ENGINEERING SERVICES

CB1

CB1
ANY USE OF THIS DRAWING WITHOUT WRITTEN
CO- NSENT BY REKAZ ENGINEERING SERVICES IS
STRICTLY PROHIBITED
B B BEAMS DETAIL 200
200 200 6. ALL EXTERNAL WALLS,VOIDS,COLUMNS, BEAMS AND
SHAFTS TO BE INSULATED

C C

B3

B3

500
REV. DATE DESCRIPTION DRAWN CHECKED

500

500
D D

B2 B3
CB1
POST TENSION SLAB
DESIGN BY SPECIALIST
POST TENSION SLAB 200 mm THICKNESS
DESIGN BY SPECIALIST
200 mm THICKNESS
E E

3 4

F B2
F
B2
B2

B2 B2

CB1
R.C.C R.C.C

B2
150MM THK. 150MM THK.
B2 B2
B2

B2

B2
B2
R.C.C R.C.C
200MM THK.

B2
ekaz
150MM THK.
G G G R.C.C G
150MM THK.

B2 B2 engineering
B2

B2
B2
B2

STAIR WELL R.C.C

150MM THK.
B2 B2
H H H H

3 4

UPPER ROOF FRAMING PLAN

SCALE 1:100

1 2 3 4 5

ROOF FLOOR FRAMING PLAN

SCALE 1:100
THIS DRAWING IS A COPYRIGHT. IT IS THE SOLE PROPERTY OF M/S REKAZ ENGINEERING ANY USE OF THIS DRAWING WITHOUT WRITTEN CO- NSENT BY REKAZ ENGINEERING IS STRICTLY PROHIBITED

SNo. NOTES

1. ALL DIMENSIONS ARE IN MILLIMETERS UNLESS

OTHERWISE STATED.

2. THIS DRAWING IS TO BE READ IN CONJUNCTION WITH

SPECIFICATIONS AND TECHNICAL DRAWINGS.

3. DO NOT SCALE FROM THE DRAWING WHERE FIGURE

DIMENSIONS ARE PROVIDED- IF IN DOUBT ASK.

4. ALL LEVELS AND DIMENSIONS SHALL BE CHECKED AT THE

SITE PRIOR TO CONSTRUCTION AND DISCREPANCIES IF
ANY TO BE NOTIFIED TO REKAZ ENGINEERING

5. THIS DRAWING IS A COPYRIGHT. IT IS THE SOLE

PROPERTY OF REKAZ ENGINEERING SERVICES
ANY USE OF THIS DRAWING WITHOUT WRITTEN
CO- NSENT BY REKAZ ENGINEERING SERVICES IS
STRICTLY PROHIBITED

6. ALL EXTERNAL WALLS,VOIDS,COLUMNS, BEAMS AND

SHAFTS TO BE INSULATED

REV. DATE DESCRIPTION DRAWN CHECKED

FOOTING DETAIL (SF1)

SCALE NOT TO SCALE
FOOTING DETAIL (SF3)
SCALE NOT TO SCALE

SCHEDULE OF FOOTINGS
FILLING LAYERS & ROAD LEVEL TYPICAL ENTRANCE STAIR DETAIL
SCALE NOT TO SCALE
FOOTING SIZE BOTTOM BARS TOP BARS
NOT TO SCALE MARK REMARKS
L X W X D ALONG L ALONG W ALONG L ALONG W

SF1 LX0.80X0.40
RY12@150mm c/c SHORT WAY, BOTTOM ONLY
RY16@150mm c/c LONG WAY, BOTTOM ONLY ekaz engineering
F1 1.6X1.80X0.40 RY16@150mm c/c BOTH WAY, BOTTOM ONLY DEEP FOOTING

SCHEDULE OF GROUND BEAMS

1 1

SCHEDULE OF SLABS

TYP. ISOLATED FOOTING'S DETAIL

SECTION:1-1 SCALE NTS

SCALE NTS
THIS DRAWING IS A COPYRIGHT. IT IS THE SOLE PROPERTY OF M/S REKAZ ENGINEERING ANY USE OF THIS DRAWING WITHOUT WRITTEN CO- NSENT BY REKAZ ENGINEERING IS STRICTLY PROHIBITED

SNo. NOTES

1. ALL DIMENSIONS ARE IN MILLIMETERS UNLESS

OTHERWISE STATED.

2. THIS DRAWING IS TO BE READ IN CONJUNCTION WITH

SPECIFICATIONS AND TECHNICAL DRAWINGS.

3. DO NOT SCALE FROM THE DRAWING WHERE FIGURE

DIMENSIONS ARE PROVIDED- IF IN DOUBT ASK.

4. ALL LEVELS AND DIMENSIONS SHALL BE CHECKED AT THE

SITE PRIOR TO CONSTRUCTION AND DISCREPANCIES IF
ANY TO BE NOTIFIED TO REKAZ ENGINEERING
TYPICAL BEAM REINFORCEMENT DETAIL
SCALE NTS
5. THIS DRAWING IS A COPYRIGHT. IT IS THE SOLE
PROPERTY OF REKAZ ENGINEERING SERVICES
ANY USE OF THIS DRAWING WITHOUT WRITTEN
CO- NSENT BY REKAZ ENGINEERING SERVICES IS
STRICTLY PROHIBITED

6. ALL EXTERNAL WALLS,VOIDS,COLUMNS, BEAMS AND

SHAFTS TO BE INSULATED

REV. DATE DESCRIPTION DRAWN CHECKED

TYPICAL SUNKEN SLAB DETAIL

SIMPLY SUPPORTED BEAM SCALE 1:25 M
SCALE NTS

TYPICAL ROOF SLAB DETAIL

30
4 Y 12 O
NOT TO SCALE

200
R8O @ 150 C/C

VARIES
COPPING DETAIL
TYPICAL LINTEL DETAILS DETAIL OF ARC REINFORCEMENT NOT TO SCALE

SCALE NTS
SCALE NOT TO SCALE

TYPICAL FLOOR SLAB DETAIL

NOT TO SCALE
ekaz engineering

SCHEDULE OF LINTELS
SPAN SIZE BOTTOM TOP
(WIDTH OF OPENING) LINKS
WxD REINF'T REINF'T

TYPICAL LINTEL DETAILS AT COLUMN TYPICAL DETAILS OF DRAINAGE TYPICAL ROOF SLAB DETAIL
NOT TO SCALE
SCALE NOT TO SCALE PIPE THRU GROUND BEAM
SCALE NOT TO SCALE
THIS DRAWING IS A COPYRIGHT. IT IS THE SOLE PROPERTY OF M/S REKAZ ENGINEERING ANY USE OF THIS DRAWING WITHOUT WRITTEN CO- NSENT BY REKAZ ENGINEERING IS STRICTLY PROHIBITED

SNo. NOTES

ALL DIMENSIONS ARE IN MILLIMETERS UNLESS

NOTE : THIS IS NOT ACTUAL STAIR CASE, THIS DETAILS ONLY FOR SHOW STEEL , FOR ACTUAL STAIR REFER TO SECTION 1.
OTHERWISE STATED.

2. THIS DRAWING IS TO BE READ IN CONJUNCTION WITH

SPECIFICATIONS AND TECHNICAL DRAWINGS.

3. DO NOT SCALE FROM THE DRAWING WHERE FIGURE

DIMENSIONS ARE PROVIDED- IF IN DOUBT ASK.

4. ALL LEVELS AND DIMENSIONS SHALL BE CHECKED AT THE

SITE PRIOR TO CONSTRUCTION AND DISCREPANCIES IF
ANY TO BE NOTIFIED TO REKAZ ENGINEERING

5. THIS DRAWING IS A COPYRIGHT. IT IS THE SOLE

PROPERTY OF REKAZ ENGINEERING SERVICES
ANY USE OF THIS DRAWING WITHOUT WRITTEN
CO- NSENT BY REKAZ ENGINEERING SERVICES IS
STRICTLY PROHIBITED

6. ALL EXTERNAL WALLS,VOIDS,COLUMNS, BEAMS AND

SHAFTS TO BE INSULATED

REV. DATE DESCRIPTION DRAWN CHECKED

FAIRFACE AND
PAINT FINISH

TYPICAL STEP DETAIL

ekaz engineering

STAIRCASE DETAILS