Public Works and Travaux publics et

Government Services Services gouvernementaux

Canada Canada

GENERAL CONCRETE REINFORCEMENT STRUCTURAL WOOD POST-INSTALLED ANCHORS AND DOWELS REAL PROPERTY SERVICES
Pacific Region
1. CONFORM TO CSA A23.1 “CONCRETE MATERIALS AND METHODS OF CONCRETE 1. WHERE DRILLED CONCRETE ANCHORS (DCA) ARE NOTED ON DRAWINGS, PROVIDE SERVICES IMMOBILIERS
1. THIS IS A METRIC PROJECT. UNLESS OTHERWISE NOTED, ALL DIMENSIONS ARE IN CONSTRUCTION”. 1. CONFORM TO CSA O86 “ENGINEERING DESIGN IN WOOD”. HILTI KWIK BOLT - TZ EXPANSION ANCHORS. EFFECTIVE EMBEDMENT LENGTHS AS
MILLIMETERS. Région de Pacifique
2. MATERIALS: FOLLOWS:
2. REINFORCEMENT - DEFORMED BAR REINFORCEMENT CONFORMING TO CSA 12 (1/2”) DIAMETER - 83 (3-1/4”) EMBEDMENT
2. PROVIDE ALL MATERIAL AND LABOUR REQUIRED FOR COMPLETION OF THE WORK. G30.18 GRADE 400R OR 400W. - LUMBER: TO CSA 141; KILN DRIED; SPF NO. 2 OR BETTER; MOISTURE
CONTENT MAX 19% UNLESS NOTED OTHERWISE ON DRAWINGS 16 (5/8”) DIAMETER - 102 (4”) EMBEDMENT
3. PRIOR TO CONSTRUCTION, REVIEW STRUCTURAL DRAWINGS IN CONJUNCTION 3. ACCESSORIES, BAR SUPPORTS, AND TIES TO CONFORM TO REINFORCING STEEL - PLYWOOD SHEATHING: TO CSA O121 DOUGLAS FIR 19 (3/4”) DIAMETER - 121 (4-3/4”) EMBEDMENT
WITH DRAWINGS PROVIDED BY ALL OTHER CONSULTANTS, AND WITH EXISTING INSTITUTE OF CANADA (RSIC) MANUAL OF STANDARD PRACTICE AND CSA A23.1 / - LAMINATED VENEER LUMBER (LVL): MINIMUM GRADE 2.0E, 3100Fb OR BETTER
CONDITIONS. A23.2. 2. WHERE ADHESIVE CONCRETE ANCHORS ARE NOTED ON DRAWINGS, PROVIDE
- NAILS: COMMON ROUND STEEL WIRE NAILS
4. REPORT DISCREPANCIES TO THE DEPARTMENTAL REPRESENTITIVE BEFORE - WOOD BOLTS: ASTM A307, 15 DIAMETER UNLESS NOTED OTHERWISE HILTI HIT-HY200 ADHESIVE ANCHORING SYSTEM WITH HILTI HIT-Z ANCHOR RODS.
4. ALL REBAR HOOKS TO BE STANDARD LENGTH 90° OR 180° HOOKS. REBAR EFFECTIVE EMBEDMENT LENGTHS AS FOLLOWS:
PROCEEDING WITH THE WORK. LENGTHS LISTED ON DRAWINGS DO NOT INCLUDE THE HOOK LENGTH. - LAG SCREWS: ANSI/ASME B18.12.1 MACHINE THREADED
12 (1/2”) DIAMETER - 114 (4-1/2”) EMBEDMENT
JOB No. 201-09709-00
5. VERIFY EXISTING DIMENSIONS AND CONDITIONS ON SITE PRIOR TO 5. FIELD BENDING OF BARS IS NOT PERMITTED UNLESS INDICATED OR APPROVED 3. UNLESS NOTED OTHERWISE, ALL WOOD FRAMING DETAILS TO BE IN 16 (5/8”) DIAMETER - 143 (5-5/8”) EMBEDMENT
CONSTRUCTION. BY DEPARTMENTAL REPRESENTIVE. APPROVED FIELD BENDING TO BE DONE ACCORDANCE WITH PART 9 OF THE REFERENCED BUILDING CODE. 19 (3/4”) DIAMETER - 171 (6-3/4”) EMBEDMENT
6. DO NOT SCALE THESE DRAWINGS. WITHOUT THE USE OF HEAT, THROUGH APPLICATION OF SLOW AND STEADY 4. PROTECT ALL WOOD PRODUCTS FROM THE ELEMENTS AS REQUIRED TO
PRESSURE. REPLACE BARS WITH CRACKS OR SPLITS. 3. WHERE REBAR DOWELS ARE NOTED ON DRAWINGS, PROVIDE HILTI HIT-HY200
MAINTAIN THEIR INTEGRITY.
7. DRAWINGS SHOW COMPLETED STRUCTURE ONLY. THEY DO NOT SHOW ADHESIVE ANCHORING SYSTEM INSTALLED USING HILTI SAFESET HOLLOW DRILL
TEMPORARY WORKS FOR WHICH THE CONTRACTOR IS RESPONSIBLE AND WHICH 6. ALL REINFORCING TO BE CLEAN, FREE OF LOOSE SCALE, OIL, DIRT, RUST, AND 5. PROVIDE ALL ERECTION BRACING REQUIRED TO KEEP THE STRUCTURE STABLE BIT TECHNOLOGY. EFFECTIVE EMBEDMENT LENGTHS AS FOLLOWS:
MAY BE REQUIRED FOR EXECUTION OF THE PROJECT. THE CONTRACTOR TO ANY OTHER FOREIGN COATING THAT AFFECT BONDING CAPACITY. AND IN ALIGNMENT DURING CONSTRUCTION. 12 (1/2”) DIAMETER - 114 (4-1/2”) EMBEDMENT
ESTABLISH CONSTRUCTION PROCEDURE AND SEQUENCE TO ENSURE SAFETY OF 16 (5/8”) DIAMETER - 143 (5-5/8”) EMBEDMENT
7. ALL REBAR LAP SPLICES TO BE COMPLETED AS PER THE GENERAL LAP SPLICE 6. SUBSTITUTION OF COMMON NAILS WITH POWER DRIVEN NAILS OF THE SAME
THE WHOLE STRUCTURE AND ALL ITS COMPONENTS DURING ERECTION. TABLE. 19 (3/4”) DIAMETER - 171 (6-3/4”) EMBEDMENT
LENGTH AND DIAMETER IS ACCEPTABLE. SUBSTITUTION OF POWER DRIVEN NAILS
8. MAKE ADEQUATE PROVISIONS FOR ALL LOADS ACTING ON THE STRUCTURE 8. FOR CLASS F-1 AND F-2 CONCRETE, MINIMUM COVER TO BE 40 (1 1/2”). OF SMALLER DIAMETER MUST BE APPROVED IN WRITING BY THE DEPARTMENTAL
4. WHERE ANCHORS ARE INSTALLED OUTSIDE OF VAPOUR BARRIER, PROVIDE
DURING ERECTION. PROVIDE TEMPORARY SHORING AND BRACING TO KEEP THE REPRESENTATIVE PRIOR TO USE. POWER DRIVEN NAILS NOT TO BE OVER-DRIVEN
STAINLESS STEEL ANCHORS.
STRUCTURE PLUMB AND IN TRUE ALIGNMENT DURING CONSTRUCTION. 9. INCREASE COVER WHERE REQUIRED TO MAINTAIN MINIMUM RATIO OF COVER TO INTO WOOD OR SHEATHING.
NOMINAL BAR DIAMETER OF 1 FOR CLASS N, 1.5 FOR CLASSES F1 AND C1 (FOR 5. CONCRETE TO BE MINIMUM 28 DAYS OLD AT THE TIME OF ANCHOR INSTALLATION.
9. CONSTRUCTION LOADS ON COMPLETED STRUCTURE NOT TO EXCEED DESIGN 7. ALL COMPONENTS OF BUILT UP MEMBERS TO BE CONTINUOUS FOR FULL SPAN.
MEMBRANE PROTECTED SLABS ONLY), AND 2 FOR CLASS C1 (ALL OTHER
LOADS INDICATED ON DRAWINGS. FULL DESIGN LOADS MAY ONLY BE APPLIED DO NOT SPLICE OR USE BUTT JOINTS. 6. USE DRILLING AND INSTALLATION TOOLS AND PROCEDURES PER
STRUCTURES).
AFTER THE CONCRETE REACHES ITS DESIGN STRENGTH MANUFACTURERS' RECOMMENDATIONS.
8. WHERE STUDS ARE PLACED TOGETHER TO FORM BUILT-UP COLUMNS WITHIN A
10. NOTIFY THE DEPARMENTAL REPRESENTITIVE 5 DAYS PRIOR TO CONCRETE 10. ENSURE COVER TO REINFORCEMENT IS MAINTAINED DURING CONCRETE POUR. WALL (FASTENED TO SHEATHING AT MINIMUM 300 (12”) CENTRES), BUILT UP 7. DO NOT CUT REINFORCEMENT TO ACCOMMODATE DRILLED ANCHORS AND
POURS, BACKFILLING, AND COVERING UP THE STRUCTURE WITH FINISHES. FOR COLUMNS MAY BE FASTENED WITH COMMON NAILS. NAIL INDIVIDUAL STUDS DOWELS.
FIELD REVIEWS TO ENSURE THE STRUCTURAL WORKS DETAILED ON THESE
DRAWINGS ARE COMPLETED IN GENERAL CONFORMANCE WITH THE CONTRACT
STRUCTURAL STEEL TOGETHER WITH ROWS OF 3.25Ø (0.13”Ø) NAILS SPACED AT 225 (9”) CENTRES, END
NAILS LOCATED 75 (3”) FROM BOTH ENDS, AS FOLLOWS: 8. A WHEN OBSTRUCTIONS PREVENT DRILLING HOLES IN SPECIFIED LOCATIONS TO
DOCUMENTS. THESE REVIEWS DO NOT REPLACE THE CONTRACTOR'S THE REQUIRED DEPTH, RELOCATE AT NO EXTRA COST TO THE CONTRACT.
1. CONFORM TO CSA S16 “LIMIT STATES DESIGN OF STEEL STRUCTURES”. - 38x89 (2x4): STAGGER NAILS 25 (1”) FROM ALTERNATE STUD EDGES
RESPONSIBILITY TO IMPLEMENT AND MAINTIAN A QUALITY CONTROL PROGRAM. OBTAIN WSP-S APPROVAL OF NEW LOCATIONS BEFORE DRILLING HOLES. FILL
- 38x140 (2x6) AND 38x184 (2x8): PROVIDE TWO ROWS OF NAILS 50 (2”) FROM ALL ABANDONED HOLES WITH MIN. 30MPa GROUT. DO NOT TIGHTEN ANCHORS
2. FABRICATOR TO BE CERTIFIED BY THE CANADIAN WELDING BUREAU UNDER STUD EDGES UNTIL GROUT IN ADJACENT ABANDONED HOLES REACHES 75% fc'.
DESIGN CRITERIA REQUIREMENTS OF CSA W47.1, DIVISION 1 OR 2, AND/OR CSA W55.3. - ALTERNATIVELY, BUILT-UP COLUMNS MAY BE FASTENED WITH 5.6Ø (0.22”Ø)
SDW SCREWS BY SIMPSON STRONG-TIE, ARRANGED AS ABOVE. LENGTH OF
3. WELDERS TO BE CWB CERTIFIED. WELDING TO BE IN ACCORDANCE WITH CSA
1. STRUCTURAL DESIGN IS IN ACCORDANCE WITH THE 2015 NATIONAL BUILDING W59. SCREW TO PENETRATE OUTER PLY MINIMUM 20 (3/4”).
CODE (NBC) SUPPLEMENTED BY THE 2015 NATIONAL BUILDING CODE OF CANADA 9. WHERE LVL / SAWN LUMBER MEMBERS ARE PLACED TOGETHER TO FORM
ABBREVIATIONS:
4. MATERIALS (TO CSA G40.21 UNLESS NOTED OTHERWISE):
STRUCTURAL COMMENTARY. BUILT-UP DROPPED BEAMS OR LIGHTLY LOADED FLUSH BEAMS, BEAMS MAY BE
- WIDE FLANGE SECTIONS AND CHANNELS: GRADE 350W ALT - ALTERNATE
2. THE VALUES FOR CLIMATIC DATA USED IN THE DETERMINATION OF WIND AND - PLATES, BARS AND ANGLES: GRADE 300W FASTENED WITH COMMON NAILS. NAIL INDIVIDUAL PLIES TOGETHER WITH 3.25Ø A-ROD - ANCHOR ROD
SNOW DESIGN LOADS HAVE BEEN OBTAINED FROM THE NATIONAL BUILDING (0.13”Ø) NAILS SPACED @300 ALONG LENGTH OF BEAM AND 150 (6”) FROM EACH
- HOLLOW STRUCTURAL SECTIONS (HSS): 350W CLASS “C” OR ASTM A1085 BOT - BOTTOM
CODE. THE SEISMIC DESIGN DATA WAS COLLECTED FROM THE NATURAL END, WITH ROWS CENTRED ON BEAM DEPTH, AS FOLLOWS UNLESS ALTERNATIVE
GRADE 50 (345 MPa) BLDG - BUILDING
RESOURSES CANADA (NRC) SEISMIC HAZARD CALCULATOR FOR THE PROPOSED CONNECTION IS SPECIFIED BY SUPPLIER:
- BOLTS, NUTS AND WASHERS: ASTM F3125, GRADE A325 - 89 TO 185 (3-1/2” TO 7-1/4”) DEEP: 2 ROWS @50 (2”)
NEW BUILDING LOCATION. BTWN - BETWEEN
- ANCHOR RODS: ASTM F1554 GRADE 36
- 235 TO 300 (9-1/4” TO 11-3/4”) DEEP: 3 ROWS @50 (2”) CLR - CLEAR
3. BASED ON THE USE AND OCCUPANCY, THE BUILDING IS DESIGNED TO THE - SHOP PAINT: CISC/CPMA 1-73A
- 300 TO 400 (11-3/4” TO 15-3/4”) DEEP: 4 ROWS @50 (2”) CL - CENTER LINE
REQUIREMENTS OF A NORMAL IMPORTANCE CATEGORY. - SHOP PRIMER PAINT: CISC/CPMA 2-75
- HOT DIP GALVANIZING: ASTM A123/A123M - 400 TO 500 (15-3/4” TO 19-3/4”) DEEP: 4 ROWS @75 (3”) CONC - CONCRETE
4. THE ROOF IS DESIGNED FOR A DEAD LOAD OF 1.0kPa. ALL THE FLOORS ARE - ALTERNATIVELY, BUILT-UP BEAMS MAY BE FASTENED WITH 5.6Ø (0.22”Ø) SDW
DESIGNED FOR A TOTAL DEAD LOAD OF 1.25kPa. 5. DO NOT CUT HOLES OR OTHERWISE MODIFY STRUCTURAL MEMBERS ON SITE. CONT - CONTINUOUS
SCREWS BY SIMPSON STRONG TIE, ARRANGED AS ABOVE. LENGTH OF SCREW
TO PENETRATE OUTER PLY MINIMUM 20 (3/4”). CP - COMPLETE PENETRATION WELD
5. THE FLOORS AND STAIRWAY ARE DESIGNED FOR A LIVE LOAD OF 4.8kPa. 6. DO NOT OVERSIZE ANCHOR ROD HOLES FOR SITE TOLERANCES. USE HOLE SIZES
SUGGESTED IN THE CISC “HANDBOOK OF STEEL CONSTRUCTION”. C/W - COMPLETE WITH
6. SNOW: Ss = 1.8 kPa; Sr = 0.2 kPa; Is (ULS) = 1.25; Is (SLS) = 0.9 10. CARRY ALL POSTS DOWN TO FOUNDATION. PROVIDE SOLID VERTICAL BLOCKING
DN - DOWN
7. PROTECT COMBUSTIBLE MATERIALS AND FINISHES DURING WELDING OF MATCHING SIZE OR LARGER AND IN LINE WITH POSTS AT FLOOR LEVELS TO
7. LATERAL LOADS IN THIS STRUCTURE ARE RESISTED BY SHEAR WALLS, AND ARE OPERATIONS. ACT AS SQUASH BLOCKS IN THE FLOOR SYSTEM. DP - DEEP
DETERMINED BASED ON THE WIND AND SEISMIC DATA BELOW. DWG - DRAWING
8. ALL STEEL LOCATED OUTSIDE THE BUILDING ENVELOPE'S VAPOUR BARRIER TO 11. USE JOISTS HANGERS WHERE JOISTS FRAME INTO SIDES OF SUPPORTS.
8. WIND: q50 = 0.45 kPa; Iw (ULS) = 1.25; Iw (SLS) = 0.75 EA - EACH
BE HOT DIPPED GALVANIZED.
12. FOR ENGINEERED FLOOR SYSTEMS, ALL RIM BOARD AND BLOCKING MATERIAL TO EE - EACH END
TERRAIN TYPE: OPEN
9. PROVIDE VENT HOLES IN HSS SECTIONS WHERE REQUIRED FOR GALVANIZING BE LSL/LVL, MINIMUM THICKNESS 44 (1-3/4”) UNLESS NOTED OTHERWISE ON
INTERNAL PRESSURE CATEGORY: 2 EF - EACH FACE
PROCESS. MAXIMUM SIZE 16 (5/8”) DIAMETER. DRAWINGS.
9. SEISMIC EL - ELEVATION
10. SHOP DRAWINGS FOR STRUCTURAL STEEL, STEEL CONNECTIONS, AND STEEL 13. UNTREATED WOOD NOT TO BE IN DIRECT CONTACT WITH CONCRETE, PROVIDE
EMBED - EMBEDMENT
Sa (0.2) = 0.848 Rd = 3.0 JOISTS TO BE SIGNED AND SEALED BY A PROFESSIONAL ENGINEER RESPONSIBLE FOAM GASKET BETWEEN WOOD AND CONCRETE, OR USE PRESSURE TREATED
WOOD. REFER TO PLANS FOR ADDITIONAL REQUIREMENTS. ES - EACH SIDE
Sa (0.5) = 0.751 Ro = 1.7 FOR THEIR DESIGN, RETAINED BY THE CONTRACTOR AND REGISTERED IN THE
Sa(1.0) = 0.425 Ie = 1.0 PLACE THE PROJECT IS LOCATED. EW - EACH WAY
14. PREFABRICATED WOOD JOISTS: DESIGN TO THE REFERENCE BUILDING CODE FOR
Sa(2.0) = 0.257 SITE CLASSIFICATION = E LOADS AND MAXIMUM DEFLECTIONS GIVEN IN CSA 086. DESIGN TO CONTROL EXT - EXTERIOR 3 REISSUED FOR TENDER 2021-06-18
11. CONNECT BEAMS FOR THE FORCES SHOWN ON DRAWINGS USING THE CISC
PGA = 0.369 “HANDBOOK OF STEEL CONSTRUCTION”. IF NO FORCE IS INDICATED, CONNECT VIBRATION PER CSA O86. SHOP DRAWINGS TO INCLUDE ENGINEERED DESIGNS, FL - FLOOR 2 ISSUED FOR TENDER 2021-01-28
SEISMIC FORCE RESISTING SYSTEM (SFRS): WOOD SHEAR WALLS NON-COMPOSITE BEAMS FOR THE REACTION DUE TO MAXIMUM UNIFORMLY MATERIAL GRADES, LAYOUT DRAWINGS, BRACING DETAILS, BEARING DETAILS, FND - FOUNDATION
BASE SHEAR = 20 kN DISTRIBUTED LOAD CAPACITY OF THE BEAM IN BENDING, AND CONNECT ANCHORAGE DETAILS AND CONNECTION DETAILS BETWEEN JOISTS AND TO 1 ISSUED FOR 100% REVIEW 2021-01-15
FTG - FOOTING
COMPOSITE BEAMS FOR ONE AND A HALF TIMES THE REACTION DUE TO MAXIMUM THEIR SUPPORTS. SHOP DRAWINGS (INCLUDING LAYOUTS) TO BE SIGNED AND 0 ISSUED FOR 75% REVIEW 2020-12-18
SEALED BY A PROFESSIONAL ENGINEER LICENSED IN THE PROVINCE OF BRITISH GALV - GALVANIZED
UNIFORMLY DISTRIBUTED LOAD CAPACITY OF THE NON- COMPOSITE SECTION IN
CONCRETE BENDING. COLUMIA, PRIOR TO FABRICATION. SUPPLIER SHALL PROVIDED A SCHEDULE S-B &
S-C TO THE ENGINEER OF RECORD IF REQUESTED.
GL - GRID LINE
HORIZ - HORIZONTAL
12. WHERE SLOTTED CONNECTIONS ARE SHOWN ON STRUCTURAL DRAWINGS,
1. CONFORM TO CSA A23.1 “CONCRETE MATERIALS AND METHODS OF CONCRETE H1E - HOOK ONE END
CONSTRUCTION”.
FINGER TIGHTEN BOLTS TO A SNUG FIT AND BURR THREADS TO PREVENT NUTS 15. PREFABRICATED WOOD TRUSSES: TO COMPLY WITH THE TRUSS PLATE INSTITUTE
OF CANADA (TPIC) DESIGN SPECIFICATIONS. FABRICATOR TO BE A MEMBER OF H2E - HOOK BOTH ENDS
FISHERIES AND OCEANS,
FROM WORKING LOOSE.
2. CONCRETE IS SPECIFIED PER ALTERNATIVE 1 - PERFORMANCE SPECIFICATION, THE CANADIAN WOOD TRUSS ASSOCIATION. DESIGN TO THE REFERENCE HD - HOLD DOWN REAL PROPERTY,
13. PREMIXED GROUT: NON-SHRINK, MINIMUM STRENGTH 40 MPa AT 28 DAYS. BUILDING CODE FOR LOADS AND MAXIMUM DEFLECTIONS GIVEN ON DRAWINGS.
AS OUTLINED IN CAN/CSA A23.1. THE CONTRACTOR AND THE CONCRETE
SHOP DRAWINGS TO INCLUDE ENGINEERED DESIGNS, MATERIAL GRADES, HDG - HOT DIPPED GALVANIZED SAFETY AND SECURITY
SUPPLIER TO MEET ALL CERTIFICATION, DOCUMENTATION, AND QUALITY 14. INSTALL GROUT UNDER BASE PLATES AS SOON AS STEEL WORK IS COMPLETE, IN
CONTROL REQUIREMENTS. LAYOUT DRAWINGS, BEARING DETAILS, ANCHORAGE DETAILS AND CONNECTION LG - LONG
ACCORDANCE WITH MANUFACTURER'S DIRECTIONS. PROVIDE 100% CONTACT VANCOUVER, BC
DETAILS BETWEEN TRUSSES, AND TEMPORARY AND PERMANENT BRACING AND LLH - LONG LEG HORIZONTAL
OVER GROUTED AREA. DO NOT APPLY ANY LOADS TO THE STEELWORK BEFORE
3. CONCRETE TO BE NORMAL DENSITY (MIN. 2300 kg/m3) UNLESS NOTED OTHERWISE. BRIDGING DETAILS AFFECTING THE STRUCTURAL CAPACITY OF THE TRUSSES.
LLV - LONG LEG VERTICAL
200-401 BURRARD ST.
GROUT ACHIEVES SUFFICIENT STRENGTH.
DESIGN TRUSSES TO SUPPORT ALL OVERBUILD FRAMING REQUIRED FOR ROOF
4. CEMENT TO BE PORTLAND CEMENT TYPE GU, UNLESS NOTED OTHERWISE OR GEOMETRY, DO NOT INTERRUPT ROOF SHEATHING TO ACCOMMODATE NIC - NOT IN CONTRACT
REQUIRED BY EXPOSURE CLASS. CEMENT TO CONFORM TO CSA A3000. OVERBUILD FRAMING. VAULTED TRUSSES NOT TO RELY ON SUPPORTING NTS - NOT TO SCALE
5. AGGREGATE TO CONFORM TO CSA A23.1 / A23.2. DO NOT USE RECYCLED STRUCTURE TO RESIST HORIZONTAL SPREADING OF TRUSS. SHOP DRAWINGS OC - ON CENTER KITSILANO CCG SAR
CONCRETE AS AGGREGATE. (INCLUDING LAYOUTS) TO BE SIGNED AND SEALED BY A PROFESSIONAL
OPP - OPPOSITE
ENGINEER LICENSED IN THE PROVINCE OF BRITISH COLUMBIA, PRIOR TO
6. CONCRETE ADMIXTURES SHALL NOT CONTAIN CHLORIDES. FABRICATION. SUPPLIER SHALL PROVIDED A SCHEDULE S-B & S-C TO THE PL - PLATE

7. SUBMIT CONCRETE MIX DESIGNS TO DEPARTMENTAL REPRESENTATIVE FOR

ENGINEER OF RECORD IF REQUESTED. PT - PRESSURE TREATED WORKSHOP
REVIEW BEFORE START OF WORK. REINF - REINFORCEMENT RECONSTRUCTION
REQ'D - REQUIRED
8. PERIMETER AND EXTERIOR CONCRETE CURB:
- EXPOSURE CLASS: F2 REV - REVISION
- MINIMUM COMPRESSIVE STRENGTH AT 28 DAYS: 30 MPa R/W - REINFORCE WITH KITSILANO, VANCOUVER B.C.
- NOMINAL SIZE OF COARSE AGGREGATE: 20 (3/4”) REINFORCING LAP SPLICES SIM - SIMILAR
9. PROTECT CONCRETE FROM EXCESSIVE HEAT AND DRYING. USE HOT WEATHER BAR SIZE VERTICAL LAP HORIZONTAL LAP HOOK LENGTH SOG - SLAB ON GRADE
16" [430mm] 20" [500mm] 7" [180mm] --
CONCRETING METHODS IN ACCORDANCE WITH CAN/CSA-A23.1 WHENEVER THE 10M SS - STAINLESS STEEL
OUTDOOR TEMPERATURE IS GREATER THAN 27°C. 15M 24" [600mm] 32" [800mm] 10" [250mm] SST - SIMPSON STRONG TIE
GL
10. PROTECT CONCRETE FROM FREEZING. USE COLD WEATHER CONCRETING 20M 30" [750mm] 40" [1000mm] 12" [300mm] STAGG - STAGGERED
METHODS IN ACCORDANCE WITH CAN/CSA-A23.1 WHENEVER OUTDOOR 25M 48" [1200mm] 60" [1550mm] 16" [400mm] STD - STANDARD
TEMPERATURE IS LESS THAN +5°C. ALL INSULATED COVERS, HEATERS, AND GM/CY
30M 57" [1450mm] 72" [1850mm] 24" [600mm] STIFF - STIFFENER
OTHER MATERIALS NEEDED TO PROTECT CONCRETE TO BE ON HAND PRIOR TO
HORIZONTAL WALL REINFORCING SHALL BE CONTINUOUS AROUND CORNERS AND STL - STEEL
POUR. DELIVER CONCRETE AT A TEMPERATURE BETWEEN +15°C AND +27°C. --
HOOKED AT WALL INTERSECTIONS. T&B - TOP AND BOTTOM
ENSURE A MINIMUM CONCRETE TEMPERATURE OF 10° IS MAINTAINED
ADD 2-15M CONT AT TOPS AND ENDS OF WALLS. UNLESS OTHERWISE NOTED, HOOK
THROUGHOUT THE CURING PERIOD (MINIMUM 3 DAYS). T&G - TONGUE AND GROOVE
AND LAP LENGTHS AS FOLLOWS: PREETIPAL PAUL
11. FORMWORK DESIGN, MATERIAL, FABRICATION, AND ERECTION TO CONFORM TO T/O - TOP OF
CSA S269.1 TYP - TYPICAL
U-BAR - "U" SHAPED BAR GENERAL NOTES
12. FORMWORK MATERIAL TO BE NEW EXTERIOR PLYWOOD CONFORMING TO CSA
O121, EXCEPT FOR ROUGH CONCRETE IN UNEXPOSED LOCATIONS (SUCH AS U/N, UNO - UNLESS NOTED OTHERWISE
FOUNDATIONS) WHERE USED MATERIAL IS ACCEPTABLE. U/S - UNDERSIDE
VERT - VERTICAL
WSP-S - WSP STRUCTURAL

F521A-210639 S1.01 3
1 OF 3

DM5XXXXXX
 Public Works and Travaux publics et
Government Services Services gouvernementaux
Canada Canada

REAL PROPERTY SERVICES

Pacific Region
WOOD FRAMING LEGEND SERVICES IMMOBILIERS
1200 LONG SIMPSON CS20 STRAP A B 1200 LONG SIMPSON CS20 STRAP Région de Pacifique
WOOD BEAM ONE AT WINDOW HEAD AND ONE ONE AT WINDOW HEAD AND ONE
6126
AT SILL. PROVIDE BLOCKING IN AT SILL. PROVIDE BLOCKING IN
BEHIND STUD WALL. Tf = 4.0kN BEHIND STUD WALL. Tf = 4.0kN
A = NO. OF PLYS IN BUILT-UP COL SW6

B
B = NOMINAL STUD DEPTH (6 = 2x6)

A/
A = NO. OF PLYS IN BUILT-UP COL

C)
)
B = NOMINAL STUD DEPTH (6 = 2x6)

SC

+S
H+
XX = NO. OF CRIPPLES: 3-38x140 3-38x140 3-38x140

SC
C
XX

H
S

+F
+F
3/6

3/6
B
SC = SINGLE CRIPPLE (DROPPED) (DROPPED) (DROPPED)

2/6
2/6
A/

(S C
(SC
DC = DOUBLE CRIPPLE 1 JOB No. 201-09709-00
TC = TRIPLE CRIPPLE
HD
2 H D2
FH = FULL HEIGHT

SW3
JOISTS HD
2 SC
2/6
SW
SHEAR WALLS
(SEE SCHEDULE)
38x286 @ 488 OC

3-38x184 (DROPPED)
HD

4867
HOLD DOWN

SW6
(SEE SCHEDULE)

BEARING WALL:
38x140 @ 406 TYP DN. 2
HD

16 D.FIR PLYWOOD
SHEATHING SC
HOLD DOWN SCHEDULE 2/6

MARK HOLD-DOWN HD STUDS ANCHORS 3-38x140

C
2/6

HD
S
SIMPSON 16Ø PAB (EMBED 200 (DROPPED)

2/6
S

2
HOLD DOWN CONNECTOR,

C
HD1 2-PLY 2
12kN OR SST LTTI31 INTO EXISTING CONC DECK)

HD

HD
SW6 SW6

HD
CONT 16Ø ROD W/ TAKE-UP SIMPSON 16Ø PAB (EMBED 200

2
HD2 2-PLY ES
DEVICE, 39kN OR SST SR5 INTO EXISTING CONC DECK)
HD STUDS ARE IN ADDITION TO BEARING STUDS ON PLANS

WOOD SHEAR WALL SCHEDULE

NAIL SPACING ANCHOR RODS FACTORED SHEAR SILL PLATE
MARK SHEATHING SHEAR CONNECTORS RESISTANCE (kN/m) REMARKS
EDGE INTERIOR PLATE SIZE SPACING FASTENERS

SW3 12.5 SHEATHING 75 300 75 A35 @ 400 16Ø 900 6.3

6.4Øx100LG
3.25Øx64LG NAILS
3 SECOND FLOOR WITH ROOF FRAMING
SCREWS @ 200 OC SCALE 1:50
S2.01 SCALE: 1:50
6.4Øx100LG 0 1000 2000 3000
SW6 12.5 SHEATHING 150 300 150 A35 @ 400 16Ø 1200 4.6 3.25Øx64LG NAILS
SCREWS @ 200 OC
PROVIDE BLOCKING TO ALL PLYWOOD EDGES 1000 SCALE IN MILLIMETRES

A B A B
6126 6126

9
S4.01

3 REISSUED FOR TENDER 2021-06-18

3-38x140

DC
SW3

HD
1
HD
(DROPPED) 89x235 PSL (DROPPED)

3/6
1
2 ISSUED FOR TENDER 2021-01-28
1 1
2 2 1 ISSUED FOR 100% REVIEW 2021-01-15

2/6
HD HD

2/6
600

SC
HOLDOWN, REFER 406DP I-JOISTS

SC
0 ISSUED FOR 75% REVIEW 2020-12-18
PLUG (E) VOID TO

SW3
TO 2/S2.01 @ 488 OC
GROUT 600 FROM
38 STRINGER TO SUIT TREAD 44x406 LSL 2/4 HD
(N) WALL
DEPTHS, 184 MIN THROAT, (FLUSH) 38x89 STUDS @ 406 OC
2 SC
CONNECT TO LANDING BEAM
2/6 HD1 2/6
FOR 4.2 kN FACTORED FISHERIES AND OCEANS,
MIN 150 WIDE
CONCRETE CURB REAL PROPERTY,

3-38x184 (DROPPED)
SAFETY AND SECURITY

4867
4867

SW6
PLUG (E) VOID TO

SW6
GROUT 600 FROM VANCOUVER, BC
600
(N) WALL 200-401 BURRARD ST.
2/6 2
SC HD 1
38x184 HD 4
3/

2/4
(FLUSH) 19 D.FIR PLYWOOD
SHEATHING SC KITSILANO CCG SAR

(DROPPED)
2/6

44X406 LSL
2-38x140

(FLUSH)
2/6 3-38x140
SC
SC WORKSHOP

HD
(DROPPED) 2/6

HD

2
2 2 RECONSTRUCTION

HD
SW6

2
SW6

HD
2/6
SC

2
2/6
KITSILANO, VANCOUVER B.C.
(E) PRECAST FILL VOID BELOW HD2 (E) CONCRETE
DECK PANELS IN SW6 @ STAIRS WITH PILE CAP
NON-SHRINK GROUT 38x140 JOISTS @ 305 38x184 38 STRINGER TO SUIT TREAD --
FILL WITH NON-SHRINK FASTEN FOR 1kN (FLUSH) DEPTHS, 184 MIN THROAT,
GROUT SECOND VOID OF FACTORED, OR CONNECT TO LANDING BEAM
(E) CONCRETE FOR 4.2 kN FACTORED
GL
FIRST AND THIRD DECK SIMPSON LU26L
PILE CAP
PANEL FROM SOUTH
GM/CY

--

PREETIPAL PAUL

1 PLAN AT EXISTING WHARF 2 GROUND FLOOR WITH SECOND FLOOR FRAMING

S2.01 SCALE: 1:50 S2.01 SCALE: 1:50 FRAMING PLANS

F521A-210639 S2.01 3
2 OF 3

DM5XXXXXX
 Public Works and Travaux publics et
SHEATHING. REFER TO Government Services Services gouvernementaux
PLAN OR SHEAR WALL Canada Canada

SCHEDULE REAL PROPERTY SERVICES

SOLID BLOCKING HOLDOWNS (HD) Pacific Region
BETWEEN JOISTS WITH ANCHORS SERVICES IMMOBILIERS
COUPLERS TO
MATCH ROD SIZES Région de Pacifique

BASE PLATE AND SHRINKAGE

PLATE TAKE-UP DEVICE BY SUPPLIER
FASTENER TO MATCH ROD CAPACITY
SPACING
PROVIDE CRUSH BLOCKING AT
COLUMN ABOVE (SHORT
STUDS/POSTS OR LSL BLOCKING)
JOB No. 201-09709-00

CONT TOP PLATE, LAP AS PER

PLAN NOTES AND TYPICAL DETAILS
SHEAR WALL
CONNECTOR SPACING STUDS LINTEL/BEAM, REFER
TO PLAN

COMPRESSION MEMBERS
EACH SIDE OF ANCHORS,
PANEL EDGE BLOCKING TO SUPPORT
REFER TO SHEARWALL
NAIL SPACING PANEL EDGE
SCHEDULE

HOLDOWN STUDS, AS

600 OR AS REQUIRED
BY MANUFACTURER
END POST/COLUMN AS PER SHEARWALL
PER PLAN OR HOLDOWN SCHEDULE WALL TOP PLATES
NAIL SPACING
PANEL EDGE

STAGGER
INTERMEDIATE

SCHEDULE
NAIL SPACING

NAILS IN
OPPOSING KING STUD EACH SIDE
SHEETS HOLDOWN (HD). REFER COUPLERS AS REQ'D TO OF ANCHOR
TO PLAN OR HOLDOWN MATCH ROD STRENGTH
SCHEDULE
BEARING PLATE & TAKE
PANEL EDGE DIAPHRAGM NAILING SHEDULE 140x140 OR 89x89 D.FIR UP DEVICE, BY SUPPLIER
ANCHOR ROD, REFER BRIDGE BLOCK TO MATCH
NAIL SPACING
TO SCHEDULE PANEL WALL THICKNESS
LOCATION PLYWOOD INTERMEDIATE BOUNDARY BLOCKING CONTINUOUS ROD, REFER
ANCHOR ROD SPACING 0.5 x ANCHOR EDGES
ROD SPACING TO SHEARWALL SCHEDULE
ROOF SEE PLAN 300 OC 150 OC 150 OC UN-BLOCKED COMPRESSION MEMBERS
SHEAR WALL EXTENT
EACH SIDE OF ANCHORS,
FLOOR SEE PLAN 300 OC 150 OC 150 OC UN-BLOCKED REFER TO SHEARWALL SCALE 1:20
SCHEDULE 225 OR AS REQUIRED 0 500 1000
HOLDOWN ANCHOR ROD, NAILS TO BE 3.66Øx64LG BY MANUFACTUER
REFER TO SHEAR REFER TO SCHEDULE
WALL SCHEDULE 500 SCALE IN MILLIMETRES

CONTRACTOR TO SUBMIT SHOP

DRWINGS SHOWING HOLDOWN SCALE 1:10
1 TYPICAL GROUND FLOOR SHEARWALL ASSEMBLY PRIOR TO 2 DIAPHRAGM NAILING 3 TYPICAL TOP CONNECTION AT CONTINUOUS ROD 0 200 400 600
SCALE: NTS FABRICATION / INSTALLATION SCALE: NTS
S4.01 S4.01 S4.01 SCALE: 1:20
200 SCALE IN MILLIMETRES

76 MIN 80 MIN 76 MIN

SHEAR WALL PLATE FASTENER SHEAR WALL OR STUD WALL AS EDGE DIST TYP EDGE DIST
AT SHEAR WALL LOCATIONS APPLICABLE, REFER TO PLAN
4-64LG NAILS (MIN) 4-64LG NAILS (MIN)

EQ EQ EQ
DIAPHRAGM BOUNDARY NAILING BLOCKING @ 1200 MAX, UNO DIAPHRAGM BOUNDARY NAILING
38 THK BLOCKING @ REFER TO PLAN WITH JOIST HANGERS REFER TO PLAN
1200 OC MIN UNO (OR APPROVED EQUAL)
SAWN LUMBER JOIST, SHEAR WALL EDGE NAILING 22 (TOTAL) 3.66Øx76LG NAILS STAGG
ENGINEERED JOIST,
REFER TO PLAN AT SHEAR WALL LOCATIONS
REFER TO PLAN 3 REISSUED FOR TENDER 2021-06-18

2 ISSUED FOR TENDER 2021-01-28

38 THK WOOD BLOCKING 44 WIDE ENGINEERED WOOD 1200 MIN OVERLAP 1 ISSUED FOR 100% REVIEW 2021-01-15
BETWEEN PERPENDICULAR BLOCKING BETWEEN PERPENDICULAR
BLOCKING, WHERE REQUIRED BLOCKING,WHERE REQUIRED SPF#1 DOUBLE TOP PLATE 38x_ 0 ISSUED FOR 75% REVIEW 2020-12-18

CONTINUOUS 38 THK TO MATCH WALL THICKNESS

CONTINUOUS 44 WIDE
WOOD RIM BOARD ENGINEERED WOOD RIM BOARD
SHEAR WALL EDGE NAILING SHEAR WALL EDGE NAILING
CONNECT FOR 3kN OR SIMPSON A35
@ 600 OC EXCEPT AT SHEARWALL, AT SHEAR WALL LOCATIONS
CONNECT FOR 3kN OR SIMPSON A35
@ 600 OC EXCEPT AT SHEARWALL, AT SHEAR WALL LOCATIONS FISHERIES AND OCEANS,
REFER TO SHEARWALL SCHEDULE
CONTINUOUS DOUBLE TOP PLATE U/N REFER TO SHEARWALL SCHEDULE
CONTINUOUS DOUBLE TOP PLATE U/N REAL PROPERTY,
FOR CONNECTION FOR CONNECTION
SHEAR WALL OR STUD WALL, SHEAR WALL OR STUD WALL,
SAFETY AND SECURITY
SHEAR WALL EDGE NAILING SHEAR WALL EDGE NAILING
AT SHEAR WALL LOCATIONS REFER TO PLAN AT SHEAR WALL LOCATIONS REFER TO PLAN WALL STUDS VANCOUVER, BC
200-401 BURRARD ST.

4 ROOF JOIST PARALLEL TO EXTERIOR WALL 6 JOIST PARALLEL TO EXTERIOR WALL 8 TYP TOP PLATE JOINT (UNO)
S4.01 SCALE: NTS S4.01 SCALE: NTS
KITSILANO CCG SAR
S4.01 SCALE: 1:10

WORKSHOP
SHEAR WALL PLATE FASTENER
AT SHEAR WALL LOCATIONS RECONSTRUCTION
DIAPHRAGM
3-64LG NAILS
SHEAR WALL PLATE FASTENER BOUNDARY
AT SHEAR WALL LOCATIONS SHEAR WALL OR STUD WALL AS NAILING
38x140 JOIST, PROVIDE KITSILANO, VANCOUVER B.C.
SQUASH BLOCKS BY APPLICABLE, REFER TO PLAN
CONTINUOUS DOUBLE 4 TOE NAILS TO WALL
TOP PLATE U/N MANUFACTURER (WHERE PLATE SHEAR WALL
DIAPHRAGM BOUNDARY NAILING REQUIRED) DIAPHRAGM BOUNDARY NAILING EDGE NAILING --
REFER TO PLAN CONTINUOUS DOUBLE REFER TO PLAN
TOP PLATE U/N BLOCKING
SHEAR WALL EDGE NAILING GL
SAWN LUMBER JOIST ENGINEERED JOIST, 16Øx250LG ANCHOR
AT SHEAR WALL LOCATIONS
TOE NAIL BOTH SIDE REFER TO PLAN BOLTS SPACED AS PER
FACES DOWN TO WALL,
CORE HOLE THROUGH (E)
SHEARWALL SCHEDULE
45x406 PSL E D GM/CY

US
REFER TO PLAN CONTINUOUS
38 THK WOOD BLOCKING TOPPING TO GROUT HOLLOW MIN 150 THK CONC CURB RIM BOARD
BETWEEN PERPENDICULAR
BLOCKING, WHERE REQUIRED
44 WIDE ENGINEERED WOOD
BLOCKING BETWEEN JOISTS
VOID BELOW NEW WALL, TYP
ALONG GRIDS 1 & 2. DO NOT
R/W CONT 15M + 15M VERTS
OT --
@ 600 OC, ADHESIVE SET
N
MIN
200
(WHERE REQUIRED) CORE OVER WEBS 250 INTO (E) WHARF DECK SHEAR WALL
CONTINUOUS 38 THK PREETIPAL PAUL
WOOD RIM BOARD EDGE NAILING
CONTINUOUS 44 WIDE
CONNECT FOR 3kN OR SIMPSON A35 CONNECT FOR 3kN OR SIMPSON A35 ENGINEERED WOOD RIM BOARD
@ 600 OC EXCEPT AT SHEARWALL, @ 600 OC EXCEPT AT SHEARWALL, TYPICAL DETAILS
REFER TO SHEARWALL SCHEDULE SHEAR WALL EDGE NAILING REFER TO SHEARWALL SCHEDULE SHEAR WALL EDGE NAILING
AT SHEAR WALL LOCATIONS AT SHEAR WALL LOCATIONS CONNECT FOR Vf = 3kN OR SIMPSON
FOR CONNECTION FOR CONNECTION
A35 @ 600 SEE SHEARWALL
SHEAR WALL EDGE NAILING SHEAR WALL OR STUD WALL, SHEAR WALL EDGE NAILING SHEAR WALL OR STUD WALL, SCHEDULE FOR SPACING AT 38x89 @ 610
AT SHEAR WALL LOCATIONS REFER TO PLAN AT SHEAR WALL LOCATIONS REFER TO PLAN SHEARWALLS CEILING
FRAMING
AWAY FROM
ROLL-UP DOOR

5 ROOF JOIST PERPENDICULAR TO EXTERIOR WALL 7 JOIST PERPENDICULAR TO EXTERIOR WALL 9 SECTION 10 SECTION
SCALE: 1:20
S4.01 SCALE: NTS S4.01 SCALE: NTS S4.01
S4.01 SCALE: NTS F521A-210639 S4.01 3
3 OF 3

DM5XXXXXX