BASE PLATE FOR COLUMNS

MARK: BP-1 min.bolt length

=D*12
122.5 105 122.5 350

70

105 + +
210
105
+ + 307.34

70
+ +
350
254

summary
B.plate A. bolts
C B t D L no of bolts
mm mm mm mm mm pcs
350 350 20 20 500 6

1
 COMPOSITE SLABS

PROJECT
LOCATION

SCHEDULE OF COMPOSITE SLABS:

DIMENSIONS(mm) BARS-mm NOTE:
MARK TYPE BAR Ø(mm)
L W T BOTHWAYS SHEET THK=0.8mm TO 1mm
DECK-1 COMP. VARIES VARIES 100 10 305

1
 COMPOSITE SLABS

SCHEDULE OF COMPOSITE SLABS:

2
COMPOSITE SLABS

10Ø AT 305mm
10Ø AT 305mm

10Ø AT 305mm
10Ø AT 305mm

3
 DESIGN OF HALF TURN STAIRS

x-axis mm w conc. 23.5 kn/m^3

x1 2000 H 3 m
x2 1000 b(step wd) 1000 mm
3000 y3
y2=gap
y- axis mm y1
y1 1000
y2 200 x1 x2
y3 1000
2200

RUNS ht level
flights pcs mm mm act.riser
f1 8 2000 1500 mm
f2 8 2000 1500 187.5
checking 16 3000

SUMMARY
act.riser tread D step wd m. barØ s d. barØ s
mm mm mm mm mm mm mm mm
187.5 250 150 1000 12 150 12 300

1
 SCHEDULE OF COLUMNS FTGS-5

PROJECT
LOCATION note:
clear conc. cover=40mm
SCHEDULE OF COLUMNS
MARK DIMENSIONS(mm)
HT. LEVEL BAR Ø(mm) SECTION (pcs) SPACING OF LAT. TIES(10mmØ)
B D

BASE
TO PED 500 500 20 8 1 at .050m, . Rest at .20m o c.
PED

BASE
TO PED2 400 400 16 8 1 at .050m, . Rest at .20m o c.
PED2

ACI CODE NOTE:more than 4 pcs main bars,please provide additional ties
NOTE: USE 8mm Ø as additional link to column rebars

note:
clear conc. cover=75mm SCHEDULE OF FOOTINGS:
DIMENSIONS(mm) BARS(pcs)
MARK TYPE BAR Ø(mm)
L W D t BOTHWAYS
F1 ISOLATED 2500 2500 2000 400 20 16
F2 ISOLATED 2900 2900 2000 400 20 20

NOTE: DEPTH OF EXCAVATION SHALL BE BASED ON NATURAL GRADE LINE (NGL).

1
 SCHEDULE OF COLUMNS FTGS-5

SCHEDULE OF MAT FOOTINGS

DIMENSIONS(mm) <-------REQUIRED DETAILING-------->
MARK TYPE
L W D t ***TOP FIBER*** ***BOTTOM FIBER***
F2 COMB 5060 5000 2000 500 REBARS REBARS
// to L // to W // to L // to W
note: 16Ø AT 200 16Ø AT 200 16Ø AT 200 16Ø AT 200
clear conc. cover=80mm

2.0 M

TOP FIBER

CHAIR BAR DIMENSION BOTTOM FIBER

t COVER bar Ǿ A B C SPACING PCS CHAIR bar Ǿ

mm mm mm mm mm mm m 1SQ MT COVER mm
500 75 16 500 286 600 1.0 1.0 8

2
 SCHEDULE OF BEAMS-4

PROJECT
LOCATION note:
clear conc. cover=40mm
SCHEDULE OF BEAMS
DIMENSIONS(mm) REBARS DETAILS
MARK BAR Ø(mm) SPACING OF 10mmØ STIRRURS
B H AT SUPPORT(pcs) AT MIDSPAN(pcs)

3 2 CRITICAL SEGMENT BALANCE SEGMENT

FTB1 300 500 20
2 3 at .15 m c/c at .20 m c/c

4 2 CRITICAL SEGMENT BALANCE SEGMENT

FTB2/GB1 300 500 20
2 4 at .15 m c/c at .20 m c/c

Nominal Grades of Concrete

Concrete Grade Mix Ratio Compressive Strength Water-Cement-Ratio

MPa (N/mm^2 ) psi liters/40kg-cement

M20 1:1.5:3:0.50 20 3000 20

1
SCHEDULE OF BEAMS-4

NOTE:location of
vertical stirrups in beams

spacers are nothing but the small piece

of steel bar put between two layers

LAPPING LENGTH (ACI CODE 318-14)

FOR TENSION MEMBER (RCC BEAM)

48D

FOR COMPRESSION MEMBER (RCC COLUMN)

60D

WHERE D -DIAMETER OF BAR

2
SCHEDULE OF BEAMS-4

note:
at least 2 bars should go
full length of beam

CURTAILMENT OF BARS IN BEAMS

(ACI 318-14)

3
 SCHEDULES OF STEEL BEAMS COLUMNS-4

conversion
inches mm
1 25.4

HORIZONTAL MEMBERS
ASSIGNMENT SECTION NAME DEPTH WIDTH FLANGE WEB WT WT
MARK mm mm mm mm LB/FT KG/M
SB1 W 14 × 34 355.1 171.3 11.6 7.2 34 50.75
(WF 14"X 7")

SB2/SRB1 W 12 × 26 310.4 164.8 9.7 5.8 26 38.82

(WF 12"X 6.5")

SRB2 W 14 × 132 373.4 373.4 26.26 16.38 132 196.9

(WF 14"X 14")

1
 SCHEDULES OF STEEL BEAMS COLUMNS-4

VERTICAL MEMBERS
conversion
HT. LEVEL ASSIGNMENT SECTION NAME DEPTH WIDTH FLANGE WEB WT WT inches mm
MARK mm mm mm mm LB/FT KG/M 1 25.4
PEDESTAL SC1 W12X53 307.34 254 14.6 8.76 53 79.16
TO (WF 12"X 10")
ROOF BEAM

2
 DETAILING OF ELEVATOR WALL

note:
clear conc. cover=25mm
WALL THK=250mm

TOP VIEW
LAYER 1
1-MT STRIP WALL

LAYER 2

12barØ AT 250mm
ELEVATION VIEW OF WALL

note:
adopt 8mmØ clips placed @ mid height of wall