Scribd
Upload
87 views5 pages

4m Transverter

This document summarizes the modifications made to the DK7ZB 50 MHz transverter design to adapt it for operation on the 70 MHz band. Key changes include using a 42 MHz oscillator instead of 22 MHz, replacing transistors for better gain at 70 MHz, and adding a final linear amplifier stage to provide approximately 10W output power. Performance testing indicates the receiver performs comparably to a commercial transverter, while the transmitter provides 10W output with 0.5W drive.

Uploaded by

sjoerdbrattinga
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
87 views5 pages

4m Transverter

This document summarizes the modifications made to the DK7ZB 50 MHz transverter design to adapt it for operation on the 70 MHz band. Key changes include using a 42 MHz oscillator instead of 22 MHz, replacing transistors for better gain at 70 MHz, and adding a final linear amplifier stage to provide approximately 10W output power. Performance testing indicates the receiver performs comparably to a commercial transverter, while the transmitter provides 10W output with 0.5W drive.

Uploaded by

sjoerdbrattinga
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 5

28/70 MHz Transverter – based on DK7ZB design for 50 MHz

by Julian Iredale, G8HCZ

The circuit diagram is essentially the same as that described in the files accompanying thiese
notes. DK7ZB has designed a 50 MHz transverter – details in German here

http://www.dk7zb.fox28.de/start1.htm

there is also an English translation at:

http://www.qsl.net/dl5dbm/

This is an excellent design and I have been using this on 6m for some time. Having built a
number of Meon transverters for 70 MHz I wanted to try and modify the DK7ZB design for this
band and compare its performance to the Meon.

Modifications

The main modifications are;

Oscillator

This is a single 22 MHz oscillator in the original design and I have modified this as shown
below to give 42 MHz to mix with 28 MHz :
Linear

The 2SC1302 linear does not have enough gain at 70 MHz and this has been replaced by the
following:

A final linear to give an output of about 10w was required and this has been added as a
design from the VHF/UHF Dx book, using a BLW60 transistor as shown below;
Antenna and power switching is performed on a separate PCB as shown:

Obviously tuned circuits have been re-scaled for 70 rather than 50 MHz throughout.

The internals of the finished unit are shown below:


Clockwise from top left:

Tx mixer, Oscillator and Rx mixer, Antenna and power switching, Final linear, driver linear.

The front panel (shown above has a meter to display power output – as in the original and full
scale is approx 10w. there are LEDs to show power on (green) and Tx (red).

The rear panel is shown below:

From top LHS clockwise:

PTT out (phono) to drive an external linear


Rx input at 28 MHz (BNC)
Tx input at 28 MHz (BNC)
Antenna (N-type)
Power input (4mm)
PTTin/power input (DIN)

The ptt input is connected visa the 5-pin DIN socket and the power in can be either connected
here or via the 4mm soclets/screw terminals.

The DIN wiring is shown below (as viewed in the picture)

Performance

Rx

On Rx the Transverter is indestiguishable from the performance of the PW Meon. I can clearly
read GB3BAA in tring and GB3RAL in Oxford at all times. GB3ANG in Fife is variable
depending on conditions. There is one minor drawback – because thwe oscillator is tripled
from 14 MHz to get 42 MHz there is a birdie at 28 MHz (14 x 2) and this obscures the beacon
at GB3BUX on 50.000. Rx gain is sufficient and in practice an attenuator will be necessary
with most transceivers to avoid a background S3 to s5.

The transceiver needs to have separate Tx and Rx outputs. Most commercial transceivers
either have this or can easily be modified to do so.

Tx

Approx 10w output is available for 0.5w drive from a suitable 28 Mhz transceiver. Linearity
appears good.

CAUTION – DO NOT USE MORE THAN 0.5W INPUT Otherwise damage may occur to the
mixer.

You might also like