MGate 5111 Series

1-port Modbus/PROFINET/EtherNet/IP to PROFIBUS slave gateways

Features and Benefits

• Converts Modbus, PROFINET, or EtherNet/IP to PROFIBUS

• Supports PROFIBUS DP V0 slave

• Supports Modbus RTU/ASCII/TCP master/client and slave/server

• Supports EtherNet/IP Adapter

• Supports PROFINET IO device

• Effortless configuration via web-based wizard

• Built-in Ethernet cascading for easy wiring

• Embedded traffic monitoring/diagnostic information for easy troubleshooting

• Status monitoring and fault protection for easy maintenance

• microSD card for configuration backup/duplication and event logs

• Supports redundant dual DC power inputs and 1 relay output

• Serial port with 2 kV isolation protection

• -40 to 75°C wide operating temperature models available

• Security features based on IEC 62443

Certifications

Introduction
MGate 5111 industrial Ethernet gateways convert data from Modbus RTU/ASCII/TCP, EtherNet/IP, or PROFINET to PROFIBUS protocols. All
models are protected by a rugged metal housing, are DIN-rail mountable, and offer built-in serial isolation.
Modbus is one of the most widely used industrial communication protocols, and EtherNet/IP, PROFINET, and PROFIBUS are commonly used in
factory automation and process automation. The MGate 5111 supports both Modbus RTU/ASCII/TCP master and slave modes, so that you can
easily connect your Modbus device to PROFIBUS PLCs or DCSs, such as Siemens PLCs.
For system integration, the MGate 5111 can connect to EtherNet/IP PLC/SCADA systems, such as Rockwell Automation PLCs, to PROFIBUS PLC/
DCS systems, or between a new Siemens PLC system that supports PROFINET to an existing PROFIBUS system. The MGate 5111 gateways are
designed for easy configuration and quick maintenance. A handy web console can be used to implement remote maintenance tasks, and the
configuration wizard UI lets you quickly set up your gateway. A comprehensive collection of troubleshooting tools reduce configuration time and
system downtime. The rugged design is suitable for industrial applications, such as factory automation, power, oil and gas, water and wastewater,
and other process automation industries.

Easy Configuration
The MGate 5111 Series has a user-friendly interface that lets you quickly set up protocol conversion routines for most applications, doing away
with what were often time-consuming tasks in which users had to implement detailed parameter configurations one by one. With Quick Setup, you
can easily access protocol conversion modes and finish the configuration in a few steps.
The MGate 5111 supports a web console and Telnet console for remote maintenance. Encryption communication functions, including HTTPS and
SSH, are supported to provide better network security. In addition, system monitoring functions are provided to record network connections and
system log events.

A Variety of Maintenance Functions

The MGate 5111 supports Protocol Diagnose and Traffic Monitor for easy troubleshooting, especially during the installation stage. Communication
issues caused by incorrect software parameters, such as slave IDs and register addresses, or incorrect command configurations, can be fished out
with Protocol Diagnose and Traffic Monitoring, which let you capture and check data to easily identify root causes.
MGate 5111 gateways also support status monitoring and fault protection functions. The status monitoring function notifies a PLC/DCS/SCADA
system when a Modbus device gets disconnected or does not respond, in which case the process PLC/DCS gets the status of each end device
and then issues alarms to notify operators. When a PROFIBUS cable gets disconnected, the fault protection function executes actions on end
devices identified by a predefined value set by the user.

1 www.moxa.com
Specifications
Ethernet Interface
10/100BaseT(X) Ports (RJ45 connector) 2
Auto MDI/MDI-X connection

Magnetic Isolation Protection 1.5 kV (built-in)

Ethernet Software Features

Industrial Protocols Modbus TCP Client (Master), Modbus TCP Server (Slave), PROFINET IO Device,
EtherNet/IP Adapter

Configuration Options Web Console (HTTP/HTTPS), Device Search Utility (DSU), Telnet Console

Management ARP, DHCP Client, DNS, HTTP, HTTPS, SMTP, SNMP Trap, SNMPv1/v2c/v3, TCP/IP,
Telnet, SSH, UDP, NTP Client

MIB RFC1213, RFC1317

Time Management NTP Client

Serial Interface
Console Port RS-232 (TxD, RxD, GND), 8-pin RJ45 (115200, n, 8, 1)

No. of Ports 1

Connector DB9 male

Serial Standards RS-232/422/485

Baudrate 50 bps to 921.6 kbps

Data Bits 7, 8

Parity None, Even, Odd, Space, Mark

Stop Bits 1, 2

Flow Control RTS Toggle (RS-232 only), RTS/CTS

RS-485 Data Direction Control ADDC® (automatic data direction control)

Pull High/Low Resistor for RS-485 1 kilo-ohm, 150 kilo-ohms

Terminator for RS-485 120 ohms

Isolation 2 kV (built-in)

Serial Signals
RS-232 TxD, RxD, RTS, CTS, DTR, DSR, DCD, GND

RS-422 Tx+, Tx-, Rx+, Rx-, GND

RS-485-2w Data+, Data-, GND

RS-485-4w Tx+, Tx-, Rx+, Rx-, GND

Serial Software Features

Configuration Options Serial Console

Industrial Protocols PROFIBUS DP-V0 Slave, Modbus RTU/ASCII Master, Modbus RTU/ASCII Slave

2 www.moxa.com
Modbus RTU/ASCII
Mode Master, Slave

Functions Supported 1, 2, 3, 4, 5, 6, 15, 16, 23

Max. No. of Commands 128

Input Data Size 2048 bytes

Output Data Size 2048 bytes

Modbus TCP
Mode Client (Master), Server (Slave)

Functions Supported 1, 2, 3, 4, 5, 6, 15, 16, 23

Max. No. of Client Connections 16

Max. No. of Server Connections 32

Max. No. of Commands 128

Input Data Size 2048 bytes

Output Data Size 2048 bytes

PROFIBUS Interface
Industrial Protocols PROFIBUS DP

No. of Ports 1

Connector DB9 female

Baudrate 9600 bps to 12 Mbps

Isolation 2 kV (built-in)

Signals PROFIBUS D+, PROFIBUS D-, RTS, Signal Common, 5V

PROFIBUS
Rotary Switch PROFIBUS addresses 0-99 (addresses 100-125 supported through software
configuration)

Mode DP-V0 Slave

Max. No. of Master Connections 1

Max. No. of PROFIBUS I/O Modules 24

Input Data Size 244 bytes

Output Data Size 244 bytes

PROFINET
Mode IO Device

Max. No. of IO Controller Connections 1 (for read/write)

Input Data Size 512 bytes

Output Data Size 512 bytes

3 www.moxa.com
EtherNet/IP
Mode Adapter

CIP Objects Supported Identity, Message Router, Assembly, Connection Manager, TCP/IP interface, Ethernet
link, Port

Max. No. of Scanner Connections 1 (for read-only), 1 (for read/write)

Input Data Size 496 bytes

Output Data Size 496 bytes

Memory
microSD Slot Up to 32 GB (SD 2.0 compatible)

Power Parameters
Input Voltage 12 to 48 VDC

Input Current 416 mA @ 12 VDC

Power Connector Spring-type Euroblock terminal

Relays
Contact Current Rating Resistive load: 2 A @ 30 VDC

Physical Characteristics
Housing Metal

IP Rating IP30

Dimensions 45.8 x 105 x 134 mm (1.8 x 4.13 x 5.28 in)

Weight 589 g (1.30 lb)

Environmental Limits
Operating Temperature MGate 5111: 0 to 60°C (32 to 140°F)
MGate 5111-T: -40 to 75°C (-40 to 167°F)

Storage Temperature (package included) -40 to 85°C (-40 to 185°F)

Ambient Relative Humidity 5 to 95% (non-condensing)

Standards and Certifications

Safety EN 60950-1, UL 61010-2-201

EMC EN 61000-6-2/-6-4

EMI CISPR 32, FCC Part 15B Class A

EMS IEC 61000-4-2 ESD: Contact: 8 kV; Air: 15 kV

IEC 61000-4-3 RS: 80 MHz to 1 GHz: 10 V/m
IEC 61000-4-4 EFT: Power: 4 kV; Signal: 4 kV
IEC 61000-4-5 Surge: Power: 2 kV; Signal: 2 kV
IEC 61000-4-6 CS: 150 kHz to 80 MHz: 10 V/m; Signal: 10 V/m
IEC 61000-4-8 PFMF

Hazardous Locations ATEX, Class I Division 2, IECEx

Freefall IEC 60068-2-32

Shock IEC 60068-2-27

Vibration IEC 60068-2-6, IEC 60068-2-64

4 www.moxa.com
 MTBF
Time 718,131 hrs

Standards Telcordia SR332

Warranty
Warranty Period 5 years

Details See www.moxa.com/warranty

Package Contents
Device 1 x MGate 5111 Series gateway

Installation Kit 1 x DIN-rail kit

Documentation 1 x quick installation guide

1 x warranty card

Dimensions

Ordering Information
Model Name Operating Temp.

MGate 5111 0 to 60°C

MGate 5111-T -40 to 75°C

Accessories (sold separately)

Cables
CBL-F9M9-150 DB9 female to DB9 male serial cable, 1.5 m

CBL-F9M9-20 DB9 female to DB9 male serial cable, 20 cm

CBL-RJ45F9-150 RJ45 to DB9 female serial cable, 1.5 m

CBL-RJ45SF9-150 RJ45 to DB9 female serial shielded cable, 1.5 m

Connectors

5 www.moxa.com
Mini DB9F-to-TB DB9 female to terminal block connector

Wall-Mounting Kits
WK-51-01 Wall-mounting kit, 2 plates, 6 screws, 51.6 x 67 x 2 mm

Power Cords
CBL-PJTB-10 Non-locking barrel plug to bare-wire cable

© Moxa Inc. All rights reserved. Updated Nov 07, 2019.

This document and any portion thereof may not be reproduced or used in any manner whatsoever without the express written permission of
Moxa Inc. Product specifications subject to change without notice. Visit our website for the most up-to-date product information.

6 www.moxa.com