TAP NATSER ‘IN @tapnatser https: //waw. Facebook. com/tapnatser, ARCHITECTURE LICENSURE MOCK EXAMINATION SET 2A Day 1 Part 2 2:00 PM - PART 2: BUILDING TECHNOLOGY. SYSTEMS INSTRUCTIONS: Choose the correct answer for each of the following questions. shade only one answer in the provided answer sheet. ERASURES ARE STRICTLY NOT ALLOWED. Situational 1 - The following questions relate to BASIC STRUCTURAL DETAILS. 1. In a typical continuous RC beam, top bars are spliced where? a. near the supports c. at mid-span b. at the supports 4d. anywhere 2. A typical Grade 40 reinforcing steel bar is painted on one or both of its ends. a. white c. blue b. yellow d. red 3. At midspan of a singly reinforced beam, reinforcing bars are provided on ‘a. bottom side c. left side b. top side d. right side 4. What do you call the required enbedment length of rebar of an RC structural menber to another RC structural member (i.e., beams to columns)? a. splice length c. rebar length b. hook length d. development length 5. In a round colunn with circular ties, what is the minimum number of longitudinal bars? a. 3 bars ©. 6 b. 4 bars d. 8 ‘Situational 2 - The following questions relate to WATERPROOFING AND INSULATION SYSTEM. 6. Which type of paint also has a waterproofing effect? a. Quick dry enamel b. Elastomeric paint c. Automotive lacquer paint d. Latex paint 7. Which of the following is not an example of cementitious waterproofing. material? a. Plexibond c. Mortaflex b. Super Thoroseal d. Rain or Shine 8. What is the typical width of commercially available PE Foam Insulation? a. 600mm cc. 15¢0nm b. 100mm d. 12¢0nm Page 1 of 26ARCHITECTURE LICENSURE MOCK EXAMINATION SET 2A Day 1 Part 2 9. In a basement wall, a negative-side waterproofing material is applied on which side? a. interior side c. both sides b. exterior side d. integral to concrete 10. Which of the following is not a material used as blanket insulation? a. Fiberglass c. Polystyrene b. Mineral wool d. Natural fibers Situation 3 - The following questions relate to STEEL CONSTRUCTION. 11, Which of the following is not used to designate a particular structural steel bean section? a. Initial indicating the type of section b. Depth of the beam c. Nominal linear weight d. Cross-sectional area 12. In steel construction, what does HSS mean? a. H-section steel c. Hollow structural steel b. Hard steel size d. Hollow sized steel 13. Which type of welding does not require a gas cylinder? a. MIG welding c. Stick welding b. TIG welding d. None of the above 14. A325 is a grade of which steel product? a. structural angle ¢. structural bolt b. structural girder d. structural concrete 15. Which structural steel product has top and bottom flanges sticking out only on one side of the web? a. structural angle c. structural plate b. structural beam d. structural channel Situation 4 - The following questions relate to WALL CONSTRUCTION. 16, What is the minimum width of wall footing? a. 300mm c. 508mm b. 400mm d. 680mm a7 is a shared wall constructed along the adjoining property lines of two buildings. a. firewall c. partywall b. partition d. abutment 18. A worker referred to a particular nail as “medya”. what does he mean? a. The nail is medium size. b. The nail is 1 inch long. c. The nail is galvanized iron. d, The nail is half-inch long. 19. In a typical reinforced CHB wall, horizontal rebars are placed every of CHB. ‘a. 2 layers c. 4 layers b. 3 layers d. layer Page 2 of 26ARCHITECTURE LICENSURE MOCK EXAMINATION SET 2A Day 1 Part 2 20. The load-bearing capacity of CHBs is typically determined by its ‘a. compressive strength c. weight b. thickness d. color Situation 5 -'The following questions relate to EXTERIOR AND INTERIOR FINISHES. 21. Which of the following is not a characteristic of ACP? a. Lightweight c. Easy-to-install b. Low maintenance d. Load bearing 22. Which of the following is named as the “Marble Capital of the Philippines”? a. Bataan c, Davao b. Ronblon d. Palawan 23. Which term refers to the non-structural covering materials installed on exterior walls providing thermal insulation and weather protection? a. cladding c. damp proofing b. blasting d. Lining 24. Which of the following is not a manufacturer or supplier of stone Claddings? a. GT Stoneworks c. Decostone b. Virtuoso d. EZ Rocks 25. What do you call the thin sheets of natural or manufactured stone used as wall cladding? a. slabs c. sidings b. veneers: d. sheathing Situation 6 - The following questions relate to PLUMBING SYSTEM. 26. Which of the following pipes are typically threaded? a. Galvanized Iron pipe c. HOPE . Copper tubing 4. cPvC 27. Which type of lavatory is mre ideal for a small-spaced bathroon? a. pedestal c. undermount b. tabletop 4. corner 28. Which of the following water heaters is tankless? a. Heat pump water heater b. Storage water heater ¢. Single-point water heater d. Solar water heater 29. A 3-storey apartment building has 3 apartment units on each floor. Each unit has a standard T&B with 1 water closet, 1 lavatory, 1 floor drain, 1 shower head and 1 shower drain. How many P-traps are needed for all TAB? a. 27 pieces c. 18 pieces b. 30 pieces d. 36 pieces Page 3 of 26ARCHITECTURE LICENSURE MOCK EXAMINATION SET 2A Day 1 Part 2 3@. Which of the following is installed during plumbing rough-in? a. lavatory c. pipe fittings b. accessories d. fixtures Situation 7 - The following questions relate to FIRE PROTECTION. 31, Which of the following is considered as active fire protection? a. Fireproofing coatings c. Fire sprinklers b. Fire doors d. Firewall 32. Any person in an unsprinklered building shall travel a minimun distance of towards any fire exit door. a. 45,00m c. 15.00m b. 60.00m d. None of the above 33. The following materials can be used as firestop except a. vermiculite c. intumescent. b. polyethylene d. silicone 34, Fire-resistance ratings of buildings materials and assemblies are typically given in. ‘a. hours c. minutes b. seconds d. days 35. Spray-applied fireproofing is typically applied to a. concrete shear walls c. structural steel frames b. foundation footings d. flooring Situation 8 - The following questions relate to THERMAL INSULATION. Refer to Figure set G. 36. Which type of thermal insulation can also seal cracks and crevices? a. Figure 2 c. Figure 4 b. Figure 3 d. Figure 5 37. Refer to Figure 5. What is the most common material used for this type of insulation? ‘a. Rubber c. Steel b. Silicone d. Cellulose 38. Which of the following can be made from XPS, EPS or ISO? a. Figure 3 c. Figure 2 b. Figure 1 d. Figure 5 39, Refer to Figure 2. The shiny reflective outer layer of this type of insulation is typically made of what? a. steel c. copper b. aluminum d. paper 49. Refer to Figure 1. The typical width of this type of insulation is based fon what? a. typical span of beams b. typical distance of colums c. typical spacing of stud framing d. typical height of door opening Page 4 of 26ARCHITECTURE LICENSURE MOCK EXAMINATION SET 2A Day 1 Part 2 Situation 9 - The following questions relate to ARCHITECTURAL SYSTEMS 41. What type of door is usually used for closing commercial shops and large access openings in industrial and commercial buildings? a. Revolving door c. Rolling door b: Overhead door d. Sliding door 42. Which of the following is present in a flush door? a. Top rail c. Muntin b. Meeting stile d. None of the above 43. What is the typical thickness of commercially available door jambs? ae c. 4” Breas des 44. Which part of a typical staircase is designed to support the treads and risers? a. newel c. baluster b. stringer d. joist 45. Which can be used to change the direction of a staircase without using landings? a. newel post c. winders: b. bracket d. treads Situation 10 - The following questions relate to MECHANICAL SYSTEMS. Refer to Figure Set I. 46. Which of the following is a known brand of air conditioners? a. Royu c. Daikin b. Koten d. Omni 47. Refer to Figure 1. Which of the following items is also known as FCU? a. Item A c. Item c b. Item B d. Item D 48. Refer to Figure 1. Which of the following items is also known as ACCU? a. Item A c. Item ¢ b. Item B d. Item D 49. Refer to Figure 2. This type of cooling equipment uses what principle? a. Magnetic cooling : b. Compressive refrigeration c. Absorptive refrigeration d. Evaporative Cooling 5@. In HVAC, R22, R32 and R410 are all what? a. Types of refrigerants c. Types of compressors b. Types of coils d. Types of insulation Situation 11 - The following questions relate to DOORS AND HARDWARE. Refer to Figure Set J. 51. Which of the following is concealed within the transom header bar? a. Figure 1 c. Figure 3 b. Figure 2 d. Figure 5 Page 5 of 26ARCHITECTURE LICENSURE MOCK EXAMINATION SET 2A Day 1 Part 2 Ls 52. Which of the following is mortised into the edge of the door panel? a. Figure 2 c. Figure 4 b. Figure 3 4. Figure 5 53. Which of the following is ideal for fire door assembly? a. Figure 3 c. Figure 4 b. Figure 5 d. Figure 1 54, Which of the following is the most common type of overhead door closer? a. Figure 1 c. Figure 5 b. Figure 3 d. Figure 4 55. Which of the following is commonly used in frameless glass door assembly? a. Figure 1 c. Figure 5 b. Figure 2 d. Figure 3 ‘Situation 12 - The following questions relate to COATING SYSTEMS. 56. What type of paint is generally used for concrete surfaces? a. Fast drying enamel c. Latex b. Lacquer paint d, Oil-based paint 57. What should not be used on concrete surfaces to prevent saponification defect? a. Neutralizer c. Primer b. Latex paint d. Oil-based paint 58. The “Duco finish” is a common term used for painting a surface with what? a. Latex paint c. Quick drying enamel b. Automotive lacquer d. Neutralizer paint 59. Which coating is used to ensure better adhesion of paint to a substrate? a. Finish coat c. Intermediate coat b. Topcoat. d. Primer 62. Which of the following is a brand name of paint family is manufactured by Davies? . a. Megacryl c. Roofgard b. Permacoat d. Elastikote Situation 13 - The following questions relate to LIGHTING SYSTEMS. Refer to Figure Set K. 61. Refer to Figure 3. What do you call this device required in LEDs? a. Ballast c. Battery b. Driver d. Switch’ 62. Refer to Figure 5. What do you call this new lighting technology? a. LiFL c. Vray b. Lighting Sheet d. OLED Page 6 of 26ARCHITECTURE LICENSURE MOCK EXAMINATION SET 2A Day 1 Part 2 63. Which of the following is ideal for ambient lighting? a. Figure 1 c. Figure 4 b. Figure 3 d. Figure 5 64, Which of the following can be used for lighting a wide space such as roads, parking or courts? a. Figure 1 c. Figure 3 b. Figure 2 d. Figure 4 65. Which of the following is ideal for task or accent lighting? a. Figure 1 c. Figure 5 b. Figure 2 d. Figure 3 Situation 14 - The following questions relate to ELECTRICAL SYSTEMS. 66. Which of the following is not typically supplied to residential structures? a. Three-phase power b. Single phase power c. Alternating current (AC) power d. 220V power 67. Which type of electrical fault happens when the current passes through an alternative path through the ground and back to its source? a. Short circuit fault ¢. Open circuit fault b. Ground fault d. Closed circuit fault 68. Which type of panel board enclosure can be installed outdoors? a. NEMA-1 c. Bolt-on b. Plug-type d. NEMA-3R 69. A worker referred to a particular utility box as “AMCO box”. The utility boxes ia Ue a. embedded to concrete c. surface-mounted b. for switches d. for outlets 7@. In specifying electrical wires, ANG refers to what? a. thickness of wire c. length of wire b. material of wire d. insulation of wire Situation 15 - The following questions relate to CONSTRUCTION TOOLS AND EQUIPMENT. Refer to Figure Set L. 71. Which of the following is used for removing debris and trash from a structure? a. Figure 5 c. Figure 3 b. Figure 1 d. Figure 2 72. Which of the following is used for lifting panels using suction? a. Figure 1 c. Figure 3 b. Figure 2 d. Figure 4 73. Which of the following is used to lift cars from below? a. Figure 2 c. Figure 3 b. Figure 1 d. Figure 4 Page 7 of 26ARCHITECTURE LICENSURE MOCK EXAMINATION aN SET 2A Day 1 Part 2 74. 8. Situation 76. Ws 78. 79. 80. Situation 81. 82. a3. a4, 85. Which of the following is used for deliveririg concrete to another location? a. Figure 1 c. Figure 3 b. Figure 2 d. Figure 4 linich of the following is used to compact soil? a. Figure 1 c. Figure 3 b. Figure 5 d. Figure 4 16 - The following questions relate to REINFORCED CONCRETE CONSTRUCTION. Ready-mixed concrete is ordered by : a. Number of trucks €. Coverage Area b. Volume d. Number of coatings lihich type of sand is not ideal for reinforced concrete construction? a. River sand ¢. Industrial sand b. Concrete sand d. Beach sand Which type of sand is typically used for finishing or plastering? a. $2 c. Vibro sand b. White sand d. Lahar sand Which of the following is used to connect rebars end-to-end without lapping? ‘a. rebar couplers c. rebar epoxy b. rebar adhesive d. rebar tape Which class of concrete is used for lean concrete and footpaths? a. Class C c. Class aA b. Class 8 d. Class D 17 - The following questions relate to TOOLS AND MATERIALS. Wihich moisture protection for basement foundation is enough for structures built on higher ground? a. Waterproofing ¢. Lean concrete b. Dampproofing d. Thermal insulation What do you call the upper level of underground zone where the soil or rocks are permanently saturated with water? a. Ground line c. Water table b. Water bottom d. Aquifer The locally known “black screw” is typically used for what? a. concrete c. metal b. drywall d. roofing Which type of hammer is typically used for tile installation? a. Wood mallet c. Ball pein hammer b. Claw hammer d. Rubber mallet A ripcut saw is used to cut wood in which direction? ‘a. Along the grain d. Perpendicular to the b. Across the grain grain c. Any direction Page 8 of 26ARCHITECTURE LICENSURE MOCK EXAMINATION SET 2A Day 1 Part 2 Situation 18 - The following questions relate to TOOLS. Refer to Figure Set H. 86. Which of the following is appropriate for making small holes or pilot holes in wood? a. Item 1 c. Item 3 b: Ttem 2 d. Item 5 87. Which of the following is generally used for making holes on concrete? a. Item 1 c. Item 3 b. Item 2 d. Item 4 88. Which of the following is appropriate for making small holes on metal or Hss? a. Item 1 c. Item 3 b. Item 2 d. Item 5 89. Which of the following is known as hole saw? a. Item 3 c. Item 5 b. Item 4 d. Item 6 98. Which of the following is known as spade drill bit? a. Item 2 c. Item 4 b. Item 3 d. Item 5 Situation 19 - The following questions relate to ARCHITECTURAL SYSTEMS. Refer to Figure Set F. 91. Refer to Figure 4. What do you call this type of gate? a. Corner sliding gate c. Side swing gate b. Barn sliding gate d. Overhead rolling gate 92. Refer to Figure 5. This type of door is conmonly made of which material? a. Laminates cc. Aluminum b. Galvanized Iron d. upvc 93. Which of the following is also called barn door? 2. Figure 1 c. Figure 3 b. Figure 2 4. Figure 5 94. Refer to Figure 1. This door style is also called what? a. French door . American door b. Dutch door 4. Japanese door 95. Refer to Figure 3. What do you call this type of sliding door? a. Folding c. Insert b. Pocket d. Side Situation 20 - The following questions relate to ELECTRONIC SYSTEMS. Refer to Figure Set E. 96. Which of the following is installed outdoors? a. Figure 1 c. Figure 3 b. Figure 2— d. Figure 5 Page 9 of 26ARCHITECTURE LICENSURE MOCK EXAMINATION SET 2A Day 1 Part 2 97. Which of the following is considered tamper-resistant? a. Figure 1 c. Figure 3 b. Figure 2 d. Figure 4 98. Refer to Figure 2. Which of the following is the most common and simplest type of this device? a. PIR c. Microwave b. Ultrasonic d, Thermal 99. Refer to Figure 3. What do you call this item? a. Internet Hub c. Router b. Telephone outlet box d. CAT 7 108. Refer to Figure 5. This type of connector transmits what? a. Video only ¢. Both audio and video b. Audio only d. Power supply only Situation 21 - The following questions relate to WOOD PRODUCTS. 101. Which engineered wood product has body made from pressed thin wood veneers perpendicular to each other? a. Plyboard c. 0SB b. Plywood d. Good lumber 102. Which engineered wood product has a core of wood strips squeezed between veneer panels? a. MOF c. 088 b. Particle board d. Plyboard 103. Coconut fiber nets are also used for what? a. Waterproofing » ¢. Vapor barrier b. Erosion protection 4. Concrete curing 104. Which of the following wood defects is natural? a. Warp c. Knots b. Twisting d. Cupping 105. For the formworks framing of a concrete column, what is the typical dimension of lumber used? are cx a be x 3¥ esse Situation 22 - The following questions relate to STRUCTURAL SYSTEMS. Refer to Figure Set D. 106. Refer to Figure C. What type of arch is used in this structure? a. Inverted segmented c. Inverted catenary b. Inverted semi-circular 4. Inverted ogee 107. Refer to Figure E. What type of dome is constructed in this famous museum? a. Solid rib dome c. Geodesic dome b. Cloister vault d. Schwedler dome Page 10 of 26ARCHITECTURE LICENSURE MOCK EXAMINATION SET 2A Day 1 Part 2 108. Refer to Figure A. What do you call the structural system used in the famous structure shown? a. Space trusses c. Folded plates b. Concrete thin shell d. Hyperbolic frame 109. Refer to Figure 8. The shown skyscraper is a famous example of which tubular structural system? a. Banked tube c. Bundled tube b. Tube-in-tube d. Space trusses 110. Refer to Figure D. What do you call the supporting structures inspired by tree branches? ‘a. Dendriforms c. Folded plate b. Columar d. Biomimicry Situation 23 - The following questions relate to PLASTICS. 111. Which type of plastic can be reheated to change its shape? a. Thermosets c. Polymers b. Thermoplastics d, Silicone 112. Backing rods are typically made from what? a. Polymer c. Polyethylene b. Rubber d. Polycarbonate 113, Teflon is technically known as what? a. PTFE c. PVC b. ETFE d. GFRC 114, Which of the following is not included in the 3Rs of environmental protection? a. Reduce c. Reuse b. Remove d. Recycle 115. In plastics, EPS means what? a. Expanded Polyvinyl Sheet b. Expanded Polystyrene c. Extruded Polyvinyl Chloride d. Extended Polymer Sheet Situation 24 - The following questions relate to CONSTRUCTION METHODS. 116. What is the purpose of gaps between polycarbonate roofing sheets when installing then? a. For sealant c. For thermal expansion b. For decoration d. For sustainability 117. Lean concrete is a concrete mixture with lower content. a. Sand c. Cement b. Water d. Aggregates 11a. is also known as sprayed concrete. ‘a. Verniculite c. Sandblast b. Perlite d. Gunite Page 11 of 26ARCHITECTURE LICENSURE MOCK EXAMINATION SET 2A Day 1 Part 2 119. Self-levelling mortar is commonly used as what? ‘a. Underlayment c. Plastering b. Scratch coat d. Joint compound 120. Sag rod is a component of what? a. Wall framing c. Stair framing b. Floor framing d. Roof framing Situation 25 - The following questions relate to MASONRY CONSTRUCTION. 121. Rebokada is a local term for what? a. Finishing c. Smooth coat b. Final coat d. Scratch coat 122. Which term refers to the systematic arrangement of bricks or other building units composing a wall? a. bond c. veneer b. glazing d. course 123. Which CHB thickness is commonly used as load bearing? a. 4” c. 6” b. ” a” 124, Which of the following is a type of brick used for kilns? a. Vitreous c. Heavy-duty b. Load bearing d. Refractory 125. How many CHBs can be used per square meter of wall area? a. 15 12.5 b. 11.5 d. 10 Situation 26 - The following questions relate to ARCHITECTURAL FINISHES. Refer to Figure set C. 126. Refer to Figure 1. What do you call the material used in this wall or partition? a. Vertical cladding glass c. Corrugated glass b. Channel glass d. Linear glass 127. Refer to Figure 2. What type of glass is used in the facade of this famous Frank Gehry’s work? a. Channel glass c. Wired glass b. Glass fiber reinforced d. Fritted glass concrete 128. Refer to Figure 5. What architectural material is used for this paneling? a. Molded stone panels c. Laser-cut panels b. Wood strips d. Opaque glass panels 129, Refer to Figure 4. This waterproofing wood finish by charring the wood surface is called what? a. Shou Sugi Ban c. Fusuma b. Tokonoma d. Kofun Ban Page 12 of 26ARCHITECTURE LICENSURE MOCK EXAMINATION SET 2A Day 1 Part 2 130. Refer to Figure 3. What material is used for this intricate facade? a. Steel reinforced concrete b. Fiber concrete c. Glass fiber reinforced concrete d. Glulam Situation 27 - The following questions relate to SITE DEVELOPMENT. 131, Which of the following is used to prevent soil erosion? a. Pavement c. Drain field b. Riprap d. Batterboard 132. Which of the following is not considered as earthworks? a. Excavation ¢. Mobilization b. Embankment d. Backfilling 133. Which of the following is considered as natural process? a. Soil compaction c. Soil excavation b. Soil consolidation d. Soil poisoning 134, Which equipment is primarily used to push materials? a. grader c. excavator b. mulcher d. dozer 135. What do you call the steepest angle in which soil can be piled without slumping? a. angle of repose c. material inclination b. safety angle d. slump Limit Situation 28 - The following questions relate to LIGHTING. Refer to Figure Set B. 136. Which of the following is most often used for chandeliers? a. Figure 1 c. Figure 3 b. Figure 2 d. Figure 4 137. Which of the following is most often used without enclosures due to its elegant shape? a. Figure 1 c. Figure 4 b. Figure 2 d. Figure 5 138. Which of the following is the most common? a. Figure 1 c. Figure 3 b. Figure 2 d. Figure 4 139, Which of the following is most appropriate for directional floodlighting? a. Figure 1 c. Figure 4 b. Figure 3 d. Figure 5 140. Which of the following has the narrowest beam appropriate for spot Lights? a. Figure 1 c. Figure 4 b. Figure 2 d. Figure 3 Page 13 of 26ARCHITECTURE LICENSURE MOCK EXAMINATION SET 2A Day 1 Part 2 Situation 29 - The following questions relate to PUMP SYSTEMS. 141, What type of pump is used to pump out accumulated water in the basement? a. Jockey pump c. Sump pump b. Fire pump d. Booster pump 142. What type of pump is submerged in water storage tank? a. Positive displacement pump b. Booster pump ¢. Jockey pump d. Submersible pump 143. What type of pump is activated once sprinkler heads were opened due to fire? a. Jockey pump c. Fire pump b. Booster pump d, Centrifugal pump 144. What type of pump is used to increase the low water pressure? ‘a. Booster pump c. Fire pump b. Positive displacement d. Utility pump pump 145. What type of pump is used to maintain pressure fire sprinkler systems if no sprinkler heads are open? a. Jockey pump c. Centrifugal pump b. Fire pump d. Sump pump ‘Situation 3@ - The following questions relate to METAL PRODUCTS. Refer to Figure Set A. 146. Which of the following is used as eave soffit? a. Figure 1 c. Figure 3 b. Figure 2 d. Figure 5 147. Which of the following can be used to reduce sound transmission? a. Figure 1 c. Figure 3 b. Figure 2 d. Figure 4 148. Which of the following is used in stud wall framing? a. Figure 1 c. Figure 3 b. Figure 2 d. Figure 4 149. Which of the following is used for finishing corners where drywalls meet? a. Figure 1 c. Figure 4 b. Figure 2 d. Figure 5 150, Which of the following is used in lighting? a. Figure 5 c. Figure 3 b. Figure 4 d. Figure 2 <<< END >>> Page 14 of 26ARCHITECTURE LICENSURE MOCK EXAMINATION SET 2A Day 1 Part 2 FIGURE SET A - METAL PRODUCTS Figure 1 Figure 2 (eee Figure 3 Figure 4 Page 15 of 26ARCHITECTURE LICENSURE MOCK EXAMINATION SET 2A Day 1 Part 2 FIGURE SET B - LIGHTING Figure a Figure 2 Figure 3 Figure 4 Figure 5 Page 16 of 26ARCHITECTURE LICENSURE MOCK EXAMINATION SET 2A Day 1 Part 2 FIGURE SET C - ARCHITECTURAL FINISHES Figure 2 i, PO). ii Hl Figure 5 Page 17 of 26ARCHITECTURE LICENSURE MOCK EXAMINATION SET 2A Day 1 Part 2 FIGURE SET D - STRUCTURAL SYSTEMS Figure 2 Figure 2 Page 18 of 26ARCHITECTURE LICENSURE MOCK EXAMINATION SET 2A Day 1 Part 2 FIGURE SET E - ELECTRONIC SYSTEMS Figure 2 ] Figure 2 Figure 3 Figure 4 as Figure 5 Page 19 of 26ARCHITECTURE LICENSURE MOCK EXAMINATION SET 2A Day 1 Part 2 FIGURE SET F - ARCHITECTURAL SYSTEMS Figure 1 Figure 2 Figure 5 Page 20 of 26ARCHITECTURE LICENSURE MOCK EXAMINATION W SET 2A Day 1 Part 2 FIGURE SET G - THERMAL INSULATION Figure 2 Figure 2 Figure 3 Figure 4 Figure 5 Page 21 of 26ARCHITECTURE LICENSURE MOCK EXAMINATION SET 2A Day 1 Part 2 FIGURE SET H - TOOLS Tten 1 Tten 2 Tten 3 << Se Tten 5 Ttem 6 Page 22 of 26ARCHITECTURE LICENSURE MOCK EXAMINATION SET 2A Day 1 Part 2 FIGURE SET I - MECHANICAL SYSTEMS Figure 2 Page 23 of 26ARCHITECTURE LICENSURE MOCK EXAMINATION SET 2A Day 1 Part 2 FIGURE SET J - HARDWARE Figure i Figure 2 Figure 3 Figure 4 Figure 5 Page 24 of 26ARCHITECTURE LICENSURE MOCK EXAMINATION SET 2A Day 1 Part 2 FIGURE SET K - LIGHTING SYSTEM Figure 2 Figure 2 Figure 4 Page 25 of 26ARCHITECTURE LICENSURE MOCK EXAMINATION SET 2A Day 1 Part 2 FIGURE SET L - CONSTRUCTION TOOLS AND EQUIPMENT Figure i Figure 2 Figure 3 | + Page 26 of 26