wy will nat be reproduced ion 2, Ad 210x297. STANDARD SPECIFICATION FOR CHAIN LINK FENCING Seecrrcanon pt | per |e Wee ° [ISSUED AS STANDARD SPECIFICATION. NK PB OPC ZAK REVISION BY CHECKED | CONVENOR [CHAIRMAN (5.8. SPECIFICATION | REV ENGINEERS INDIA LIMITED | STANDARD SPECIFICATION FOR NEW DELHI CHAIN LINK FENCING 6-65-13 1 Page 1 of 7CONTENTS I not be reproduced] ey CL.NO 1.0 SCOPE 2.0 EARTHWORK FOR CIVIL WORKS 3.0 CEMENT CONCRETE FOR FOUNDATION & SILL 4.0 CEMENT CONCRETE IN PRECAST POSTS/STRUTS ‘on the borrower's express agreement 5.0 REINFORCEMENT 6.0 CHAIN LINK FENCING 3: ENGINEERS INDIA LIMITED, Th ENGINEERS INDIA LIMITED | STANDARD SPECIFICATION FOR NEW DELHI CHAIN LINK FENCING SPECIFICATION REV 6-65-13 Page 2 of 7|ot be reproduced, ‘iven by the lender to the borrower for the intended use. ElL-1641-507 A& 210x297 format are the property oF ENGINEERS INDIA LIMITED. They are merely loaned on the borrower's express agreement that they wi ited way permitted by a written cons The drawing, design and de copied, exhibited or used, except in th 1.0 SCOPE This specification specifies the requirements of chain link fence for security purposes. The height of the fence shall be approximately 2.00 m to the top of the chain link fencing at the posts and approximately 2.5 m in vertical height at the top line of barbed wire attached to the cranked tops of the posts. 2.0 EARTHWORK FOR CIVIL WORKS 21 Refer specification No. 6-68-03 3.0 CEMENT CONCRETE FOR FOUNDATION & SILL 34 Refer specification No. 6-68-04. 40 CEMENT CONCRETE IN PRECAST POSTS/STRUTS (Straining posts, intermediate posts and struts) 44 ‘Cement concrete shall be of M-15 grade with 20mm and down size crushed stone aggregates conforming to IS : 383. 42 The work shall be carried out as per IS : 456 in all respects. 43 Necessary moulds shall be provided for casting the concrete posts and the same shall, be smooth finished with 1:3 cement sand mortar as directed by the Engineer-in- Charge 44 ‘The concrete shall be cured for a minimum period of 14 days. 45 Payment for this item shall be made on cubic metre basis and the rate shall include labour, materials, mixing placing, leaving pockets, fixing chain link fencing, line wires, barbed wires inserts in concrete post while casting as shown in the drawing cr as per the directions of Engineer-in-Charge, keeping the concrete post in the proper position while concreting, scaffolding, all moulds, curing etc. complete © ENGINEERS INDIA LIMITED NEW DELHI STANDARD SPECIFICATION FOR CHAIN LINK FENCING SPECIFICATION 6-65-13 Page 3 of 7 REVwibe =| Dorrower's express agreement that they wi snded use, Ell-1641-507 Ad 210x297 The drawing, design and details given on this format are the property of ENGINEERS INDIA LIMITED. They are merely loaned on th copied, exhibited or used, except in the limited way permitted by a written consent given by the lender to the borrower for thei 5.0 51 6.0 6.1 6.11 6.1.2 6.1.2.1 6.1.2.2 6.1.2.3, 6.1.24 6.1.2.5 including handling & transportation from precasting yards to place of fixing, preparation of precasting yards etc. but excluding cost of reinforcement REINFORCEMENT Refer specification No. 6-68-04 CHAIN LINK FENCING Materials, Chain Link Fencing The material requirement shall conform to IS:2721 latest edition. The chain link fencing shall be woven from 3.55 mm dia wire with mesh size of 50 mm. The mesh wire shall not vary from the specified dia by more than -+. 0.05mm. Galvanised Wires All steel wires shall be hot dipped galvanised wire and dia of the wire shall be 355MM. over the galvanised coating The line wire shall be 4 mm dia mild steel The stirrup wire for securing the line wires to the concrete intermediate posts. sill be 2.5 mm diameter mild steel. The tying wire for securing the chain link fencing to the line wire shall be 1.6mm diameter mild steel Hair pin staples for fastening down the bottom of galvanised chain link fencing to the concrete sill shall be of 3.55 mm wire. The ends shall be bent outwards to secure anchorage. S L ENGINEERS INDIA LIMITED | STANDARD SPECIFICATION FOR SPECIFICATION =| REV NEW DELHI CHAIN LINK FENCING 6-65-13 1 Page 4 of 7|it be reproduced] Ze agreement that they wil a by the lender to the borrower for the intended use. ElL-1641-507 Ad 210x297 TA LIMITED, They are merely loaned on the borrower's ted by a written consent gi The drawing, design and details given on this format are the proporty of ENGINEERS INDI copied, exhibited or used, except in the limited way pe 6.13 6.14 6.1.4.1 6.1.4.2 6.15 6.1.7 6.1.7.1 6.1.7.2 6.1.7.3 Cleats for eye bolts shall be of uniform size and shall consists of mild steel! angle of 75x50x6 mm. Eye Bolt Strainers The eye bolt strainer shall consist of bolts with welded eye sufficiently threaded and fitted with a nut and waster, ‘Two-way eye bolt strainer shall have suitable ring nuts, fitted after wires have been strained on one side. Stretcher bar shall consist of mild steel flats 25 mm x 4.75 mm. They shall be secured to the cleats by steel bolts. Droppers for barbed wire shall be of M.S not less than 25mm x 4.75 mm thick with 38mm x 4.85 mm half round staples for fastening the barbed wire to them, Barbed Wire Barbed wire shall conform to IS : 278. The coating on the wire shall be smooth and relatively free of lumps, globes or points, wire with excessive roughness, blisters, salammoniac spots shall be rejected. Barbed wire shall be made from two strands of galvanised, twisted 2.5 mm (12 gauge) steel wire with 4 points of barbs. Each barb shall have two turns, tightening around one or both line wires making altogether four complete turns. ‘The barb shall be so finished that four points are set and looked at right angles to each other. Bracing of the rows of barbed wire shall be as shown in drawing, The barbs shall have a length of not less than 13 mm and not more than 18 mm. ie ENGINEERS INDIA LIMITED | STANDARD SPECIFICATION FOR SPECIFICATION | REV NEW DELHI CHAIN LINK FENCING 6-65-13 1 Page § of 7|rot be reproduced) Dorrower’s express agreement that they wil mended use. ElL-1641-507 Ad 210x297 “The drawing, design and details given on this format are the property of ENGINEERS INDIA LIMITED. They are mer copied, exhibited or used, except in the limited way permitted by a written consent given by the lender to the borrows 6.2 6.2.1 6.2.2 6.2.3 6.2.3.1 6.2.3.2 6.2.3.3 6.2.3.4 6.2.3.5 Erection Straining posts shall be provided at all ends and corners of fences, at changes in direction or acute variations in level and at intervals not exceeding 66 mm on straight lengths of fence. Intermediate posts shall be spaced at regular intervals not exceeding 3m. ‘Struts shall be fitted to all straining posts behind the chain link fabric in the direction of the line of fence. Fixing chain link fencing There shall be four evenly spaced rows of line doubled, making five line wires in all. The bottom wire shall be close to the ground. the top wire shall be Each line wire shall be strained tightly by means of eyebolt strainers or winders at each straining point. Each line wire shall be secured to each intermediate post by a wire stirrup passed through a hole in the posts and secured to the line wire by three complete turns on each side of the post. ‘The chain link fencing shall be strained between each pair of straining posts and secured to each straining post by means of a Stretcher bar. One of the top line wires shall be threaded through the appropriate adjacent rows of mesh, care ig taken that no meshes in the rows are bypassed by the line wire except where deviation is necessary at the straining posts. The second top line wire shall be strained in front of the fencing. The fencing shall be attached to the top and bottom line wire by wire ties spaced 150mm apart and to the other line wires by wire ties spaced 450 mm apart. The bottom of the fencing shall be treated as follows. Continuous concrete sill 125 mm wide x 225 high for full length between post shall be cast with the top 25 mm above G.L. and 25 mm below the chain link fencing, Hair pin staples shall be threaded through the bottom row of mesh at 0.75 m c/c and set in the sill to a depth of 150 mm, & ENGINEERS INDIA LIMITED | STANDARD SPECIFICATION FOR NEW DELHI CHAIN LINK FENCING 6-65-13 SPECIFICATION REV Page 6 of 7|wt be reproduced] IMITED. They are merely loaned on the borrower's express agreement that they wil the lender to the borrower for the intended use. EIL-1641-507 A4 210x297 “Tho drawing, Gevign and details given on this format are the property of ENGINEERS INDIA LI Copied, exhibited or used, except in the limited way permitted by a written consent given by tl 6.2.3.6 Payment Payment for chain link fencing shall be made on running metre basis for bottom 2.0 metre height of the total fence height including supply of chain link fencing in 1.9 metre width roll, fixing in position true to line and as per drawing. ‘The rate shall also include supplying and fixing necessary galvanised line wires, stirrup wires, tying wires, hair pin staples for fixing the fence in cone sill, etc. tensioning the line wire and fencing, all materials and labour etc. required to complete the job as per drawings and direction of Engineer-in Charge. 6.2.4 Fixing barbed wires for Anticlimbing device 624.1 ‘Three lines of barbed wire shall be provided as shown in drg, The wires shall be attached by eye bolts to the cranked tops of the straining posts. On concrete intermediate posts they shall be secured to cranked tops with stirrup wires. The barbed wire shall be fitted with one droper at the centre of each bay, secured to the wires so that they cannot be bunched together. 6.2.4.2 Payment Payment for barbed wire shall be made on running metre basis of two ply, four points barbed wire fixed in position. The rate shall included supply and fixing necessary dropers, straining bolts tensioning the barbed wire etc. and all materials and labour etc. required to complete the job. ENGINEERS INDIA LIMITED | STANDARD SPECIFICATION FoR |__SPECIFICATION | REV NEW DELHI CHAIN LINK FENCING 6-65-13 1 Page 7 of 7|