Check valve, RE 21543/07.

05
Replaces: 02.03
1/4

pilot operated

Type Z2SRK

Size 6
Component series 1X
Maximum operating pressure 210 bar
Maximum flow 40 l/min
H5547

Table of contents Features

Contents Page – Sandwich plate valve
Features 1 – Position of ports to ISO 4401-03-02-0-94
Ordering code 2 – For the leak-free isolation of two actuator ports
Function, section, circuit example, symbol 2
Technical data 3
Characteristic curves 3
Unit dimensions 4

Information on available spare parts:

www.boschrexroth.com/spc
2/4 Bosch Rexroth AG Hydraulics Z2SRK 6 RE 21543/07.05

Ordering code

Z2SRK 6 1 1X V *

Check valve, sandwich plate Further details in clear text

Size 6 =6 1)
/60 = With locating bore
Cracking pressure 1.5 bar =1 /62 = With locating bore and locating pin
ISO 8752-3x8-St
Component series 10 to 19 = 1X
(10 to 19: unchanged installation and connection dimensions) V= FKM seals
Caution!
1) Locating pin ISO 8752-3x8-St, Observe compatibility of seals
Material no. R900005694 (separate order) with hydraulic fluid used!

Function, section, circuit example, symbol ( 1 = component side, 2 = plate side)

Isolator valve type Z2SRK 6 is a pilot operated check valve of spool (1) is pressurised, shifted to the right or to the left and
sandwich plate design. causes poppet (2) to be pushed off its seat. Hydraulic fluid can
It is used for the leak-free closure of two actuator ports, even now flow from B2 to B1 or from A2 to A1.
during longer periods of standstill. To allow reliable closing of poppets (2), the actuator ports of
The oil can freely flow from A1 to A2 or B1 to B2, whereas in the directional valve must be unloaded to tank in the central po-
the opposite direction the flow is blocked. sition (see circuit example).
When fluid flows through the valve from A1 to A2 or B1 to B2,

1
A2 B2

A1 B1
P A 2 B T

P T
1
3 1
A B

3 Area A1
4 Area A2

2 A B
4 2
RE 21543/07.05 Z2SRK 6 Hydraulics Bosch Rexroth AG 3/4

Technical data (for applications outside these parameters, please consult us!)

General
Weight kg approx. 0.5
Installation orientation Optional
Ambient temperature range °C –20 to +80

Hydraulic
Maximum operating pressure bar 210
Cracking pressure in free direction bar See characteristic curves below
Maximum flow l/min 40
Direction of flow See Symbol on page 2
Hydraulic fluid Mineral oil (HL, HLP) to DIN 51524; fast bio-degradable
hydraulic fluids to VDMA 24568 (see also RE 90221); HETG
(rape seed oil); HEPG (polyglycols); HEES (synthetic esters);
other hydraulic fluids on enquiry
Hydraulic fluid temperature range °C –20 to +80
Viscosity range mm2/s 2.8 to 500
Max. permissible degree of contamination of the hy- Class 20/18/15 1)
draulic fluid - cleanliness class nach ISO 4406 (c)
Area ratio A1/A2 = 1/3 (see sectional drawing on page 2)

1) The cleanliness classes specified for components must be

adhered to in hydraulic systems. Effective filtration prevents
malfunction and, at the same time, prolongs the service life
of components.
For the selection of filters, see data sheets RE 50070,
RE 50076, RE 50081, RE 50086 and RE 50088.

Characteristic curves (measured with HLP46, ϑoil = 40 °C ± 5 °C)

Δp-qV characteristic curves

25 1 Cracking pressure 1.5 bar (from 1 to 2 )
2 Across check valve insert
Pressure differential in bar →

20 (opened from 2 to 1 )
2
15
1
10

0 10 20 30 40
Flow in l/min →
4/4 Bosch Rexroth AG Hydraulics Z2SRK 6 RE 21543/07.05

Unit dimensions (nominal dimensions in mm)

96
11 11 44
5 B
A
SW22

40
24,5
A B

4
6 3 7 1 8
16
6,5

F1 F2 0,01/100mm
T
A Rz1max 4

B Required surface quality

of mating part
F4 P G F3

27
4 x Ø5,4
4 2

1 Nameplate Valve fixing screws (separate order)

4 socket head cap screws ISO 4762 - M5 - 10.9
2 Valve fixing bores
(friction coefficien‚t µtotal = 0.14);
3 Identical seal rings for ports A, B, P, T tightening torque MT = 8.9 Nm ± 10%
4 Bore Ø3 for locating pin ISO 8752-3x8-St, (please adapt in the case of changed surfaces)
material no. R900005694 (separate order)
5 Component side
6 Plate side
7 Position of ports to ISO 4401-03-02-0-94
8 Locating pin ISO 8752-3x8-St; version “/62“ only

Bosch Rexroth AG © This document, as well as the data, specifications and other information
Hydraulics set forth in it, are the exclusive property of Bosch Rexroth AG. It may not be
Zum Eisengießer 1 reproduced or given to third parties without its consent.
97816 Lohr am Main, Germany The data specified above only serve to describe the product. No state-
Phone +49 (0) 93 52 / 18-0 ments concerning a certain condition or suitability for a certain application
Fax +49 (0) 93 52 / 18-23 58 can be derived from our information. The information given does not
[email protected] release the user from the obligation of own judgment and verification. It
www.boschrexroth.de must be remembered that our products are subject to a natural process of
wear and aging.