User ’s Ma n u a l

Tuxon- C

Ver. 2 / 2022 / 01
 Table
1.General Information ...................................................... .- 1 -
1.1 Function ...............................................................- 1 -
1.2 Description...........................................................- 2 -
1.3 Rear illustration....................................................- 3 -
1.4 Specification ........................................................- 4 -
1.5 Dimension............................................................- 5 -
2. Wiring ............................................................................- 6 -
2.1 Installation............................................................- 6 -
2.2 Power connection ................................................- 7 -
2.3 Load cell connection............................................- 7 -
2.4 I/O terminals ........................................................- 9 -
2.5 Analog output connection ..................................- 10 -
2.6 Serial port connection........................................ - 11 -
3. Calibration...................................................................- 12 -
3.1 Illumination.........................................................- 12 -
3.2 Calibration flow chart .........................................- 12 -
3.3 Millivolt display...................................................- 15 -
3.4 Calibration without weights................................- 16 -
3.5 Quick zero/gain calibration ................................- 18 -
3.6 Parameter table .................................................- 18 -
3.7 Parameter record...............................................- 18 -
4. Parameter setting........................................................- 19 -
4.1 Defination...........................................................- 19 -
4.2 Operation parameter table.................................- 21 -
5. Operation ....................................................................- 24 -
5.1 Operating status ................................................- 24 -
5.2 Operating procedure..........................................- 25 -
 5.3 Manual zeroing ................................................. .- 25 -
5.4 I/O testing ..........................................................- 26 -
5.5 I/O defination .....................................................- 27 -
5.6 Display testing ...................................................- 29 -
5.7 Reset .................................................................- 30 -
5.8 Backup...............................................................- 31 -
5.9 Restore backup .................................................- 31 -
5.10 Analog calibration ............................................- 31 -
5.11 Password .........................................................- 33 -
5.12 Password setting .............................................- 33 -
6. Serial port communication ..........................................- 34 -
6.1 RS protocol ........................................................- 34 -
6.2 RE protocol ........................................................- 45 -
6.3 MODBUS protocol .............................................- 47 -
7. Error and alarm message ...........................................- 59 -
1 General information
Tuxon-C weighing indicator is a small-volume display
specially for weighing and controlling in industrial field, which
features are abundant communication, high precision, strong
function and easy operation etc., thus to be widely used in
weighing and controlling equipment, such as concrete mixer,
asphalt batching, feeding stuff, metallurgy converter and so
on.
1.1 Function:
 Small volume, unique design, easy operation;
 Suit to all of load cells at bridge-type resistance strain
gauge;
 Multi digital filter;
 5set points are used widely to meet more requirement;
 RS232/RS485 (optional) to ensure stable communication;
 Abundant communication protocols(RS/RE/MODBUS
optional) to communicate easier with host computer;
 High precision 16bit DA analog output;
 Digital calibration with or without weights;
 Password protection for calibration, operation parameters
etc.;
 Automatic zeroing when power up;
 Automatic zero tracking.

-1-
1.2 Description

P 1-1

Keypad:

Display value when zeroing or exit present function.

：Parameters are optional.
：Set parameter mode.
：Enter parameters or calibration or confirmation.
Status indication:
：Not define
/ ：Not define
：Not define
：Zero indication light when weight is among 0±1/4d.
：Stability indication light when weight is in stable range.
Display:
Main display：6digits, display weight and parameters.
Sub-display：6digits, display analog, set point and

-2-
Set point display：1 digit, display set point numbers.

-3-
1.3 Rear illustration

P 1-2
① I/O input terminals
② I/O output terminals
③ Load cell terminals
④ Serial port / analog terminals
⑤ Power connection
⑥ Fuse socket

-4-
1.4 Specification
Common:
Power supply：AC90V～260V 50Hz (or 60Hz) ± 2%
Filter：Inside
Working temperature：-10～40℃
Max humidity：90%R.H without dew
Power consumption：About 10W
Dimension：105×151×57mm
Analog:
Load cell power：DC5V 300mA (Max)
Input impedance：10MΩ
Zero steady range：0.02～9mV
Input sensitivity：0.01uV/d
Gain input range：0.2～10mV
Transfer mode：Sigma - Delta
A/D conversion speed：120times/sec
Non-linearity：0.01%F.S
Gain drift：10PPM/℃
Display Precision：1/30000 Digital:
Weight display：6digits red high-brightness LED
Minus display：“-”
Overload display：“OFL”
Decimal point：5kinds (optional)

-5-
1.5 Dimension

-6-
2 Wiring
2.1 Installation

1. Cut hole as left size

in the suitable place of
control box.

2. Screw open in four

corners, then dismantle
mounting plates.

3. Install indicator in
the front of control box.

4. Insert mounting
plates on both sides
and then screw tightly.

P 2-1

-7-
2.2 Power connection
Tuxon-C weighing indicator connects power as follows:

P 2-2

1. AC power must connect with ground;

2. Please do not connect indicator’s earth line
with other huge electronic equipment directly.

2.3 Load cell connection

EX+: Excitation+ EX-: Excitation- SN+: Sense+ SN-: Sense- SIG+: Signal+ SIG-: Signal-

6 wires EX+ SN+ EX- SN- SIG+ SIG- Shield

4-wires EX+ EX- SIG+ SIG- Shield

1) 6 wires connection:

Load cell

2-3

-8-
2) 4 wires connection

P 2-4

1. As load cell output sensitive analog signal,

please use shield cable to separate with other
cables, especially AC power;
2. 4 wires connection is suitable for short distance
and stable temperature or low precision field,
otherwise use 6 wires connection.
3. For more load cells parallel connection, their
sensitivity (mV/V) should be same.

-9-
2.4 I/O terminals
Tuxon-C Weighing indicator transfer data by
optoelectronic isolation technology, thus need 24 V DC
outside as power supply, which anode connect with indicator
24 V+, and cathode with 24V- through the COM1 (DC+)
and the COM2 ( DC-). The input signal is low level
effective, and the output is transistor open-collector output,
which driving current can reach 500m A.
I/O definition as follows：

P 2-5
Indicator input terminal connection:

P 2-6
Indicator output terminal connection:

P 2-7
- 10
I/O tolerant definition as follows:
Output Input
OUT1 SP1 IN1 Zero

OUT2 SP2 IN2 NC

OUT3 SP3
OUT4 SP4
OUT5 SP5
OUT6 SP6

2.5 Analog output connection

Analog output two kinds: voltage and electric current. For
voltage output, 0-5V/0-10V/-5-5V/-10-10V is optional for
voltage output ； 4-20mA/0-20mA/0-24mA is optional for

electric current output. Define terminals as follows：

P 2-8

Note ： Analog output is optional function, please

- 11 -
2.6 Serial port connection
Serial port(RS485 or RS232) connection as follows：

P 2-9
RS232 connection：

P 2-10
RS485 connection：
Controller 1

Computer

.
.
. GND is ground of RS485, it can very
mu ch i mp rov e co mmu n i cat i o n
quality via connecting with GND by
Controller n

low-resistance wire when there is a lot

of disturbance in working field.

- 12 -
P 2-11

- 13 -
3 Calibration
3.1 Instruction
Tuxon-C Weighing indicator need calibrate atbeginning
of operation or changing any parts on weighing system or
non-suitable application for user. The calibration can define
radix point, minimum scale division, maximum
scale capacity, zero and gain, etc.
User can press to enter next or press to
save setting to only change one parameter, and then
press to exit.

3.2 Flow chart

Press to display
CAL，and then press
to enter
password.

Input correct password，

when display “CAL ON”
one second, then enter
to set radix point
automatically.

- 14 -
 1) Press set radix
point (0~0.0000 5 kinds
optional) ， press to
save and enter mini division.
2) If not change radix point,
press directly to enter
mini division.

1) Press to set mini

division(1~50 6kinds
optional)，press to save
and enter max. capacity.
2) If not change mini division,
press directly to enter
max. capacity.

1) Input max. capacity(≤mini

division × 30000)，press
to save and enter millivolt
display.
2) If not change, press
to enter millivolt display
directly.

1) Select suitable sensitivity

based on load cell, press
to save and enter
millivolt display. Otherwise to
press directly to enter
millivolt display.

- 15 -
 1) When load cell output
millivolt value, press to
enter zero calibration directly.
2) The display value is similar
with millivolt from SIG+/SIG-
terminals. See Character 3.3
for details.

1) When scale platform is

stable, press to take
present weight as zero，and
enter gain calibration.
2 ） Press to reserve
original zero and enter gain
calibration.
1) Gain calibration as the left
chart.
▲When calibration with
weights, please record zero
millivolt, gain millivolt and
weight value in list. If no
weights, user will calibrate
according to these data.
2) Press to enter
password directly, no gain
1) See Character 5.11 to set
password, then press to
exit calibration and return.
2) If not set password,
press directly to return.
Normal working status.

- 16 -
3.3 Millivolt display
This function is mainly used to test weighing system,
four-corner position-error of force-transmitted equipment and
load cell’s linearity.
1. Test weighing system
(1) If the indicator display variational millivolt value
according to add weight, thus indicate load cells are
connected correctly and force-transmitted equipment is
operated normally.
(2) If the indicator display OFL (or –OFL), thus indicate
the weight is too heavy (or too light), then need unload (or
add) the weight. But if always display OFL (or –OFL) after
changing weight, maybe the following reason cause:
a. Please check force-transmitted equipment.
b. Please check the load cell’s connection.
c. Please check Load cells.
2. Test four-corner position-error of force-transmitted
equipment
Please load same weight on scale’s every corner and
record individual millivolt value. If the values are obviously
different, please adjust force-transmitted equipment.
3. Test load cell’s linearity
Please load several same weight values within the
weighing capacity and record relevant millivolt value after
zeroing every time; if the discrepancy is bigger among
millivolt values, thus indicate that the load cell’s linearity is not
good, need change new load cell or adjust force-transmitted
equipment.

- 17 -
3.4 Calibration without weights
Calibration without weights is only for urgency. If change
new load cells or indicator, or adjust weighing system,
calibration without weights is not correct.

- 18 -
- 19 -
3.5 Fast zero / gain calibration
In weighing status, press for long time, when
display password input, then input password correctly and
enter zero calibration. See Character 5.10 for details.
3.6 Calibration parameter table
Initial
Sign Parameter Type Division
value
Decimal 0,0.0,0.00,0.000,
Point 5 0.0000 0
point
1d= Mini division 6 1,2,5,10,20,50 1
Max
CP ≤mini division×30000 10000
capacity
System
St
millivolt
SE Sensitivity 2 2，3 2(mV/V)
E SCAL Zero
AddLd(d) Gain
Set
PASS 000000
password

3.7 Calibration parameter record

Parameter Valued Date Remark
Decimal point position
Mini division
Max capacity
Load cell sensitivity
Password setting
List(calibration with weights)：
Zero Gain
Weights
Times millivolt millivolt Date Remark
（Kg）
（mV） （mV）
1
2
3

- 20 -
4 Parameter setting

Note ： Press to switch among

parameters；press to enter next
menu；press to return previous
menu.See Chapter 4.1 for details.

4.1 Defination
Press to select parameters, then press and
to set parameters, after that, press to save
setting.

- 21 -
1） Optional parameter setting
Set“parameterF1.1”（ON）for example:

1. Press , then sub-display

sparkle “OFF”.

2. Press , then sub-display

show“ON”.

3. Press to save setting. If not

need set other parameters, press
to return.

2） Numerical parameter setting

Set “parameter F1.3”（as 39）for example:

1. Press , sub-display sparkle “0”

in the right.

2. Press till sub-display show

“3”，then press ，sparkle move to
the right one.

3. Press till sub-display

show“9” ， then press to save
and finish.

- 22 -
4.2 Operation parameter table
No. Para. Init ial Description
F1 None None No.1 parameter
Automatic zeroing when power
F1.1 ON/OFF OFF
on
Zero tacking range(00 ～ 99d
F1.2 00～99 01 optional).
If setting 0, not zero tracking.
Zeroing range(01% ～ 99% of
F1.3 00～99 05
full capacity).
Stability criterion range(01 ～
F1.4 00～99 01 99d optional). If 0, always
stability and the light are on.
Digital filter parameter
F1.5 0~9 4
0：no filter；9：strongest filter
Stability filter
F1.6 0～9 7
0：no filter；9：strongest filter
F2 None None No.2 parameter
Set point 1 Set point 1 to 5
F2.1 ×××××× 0 (maximum. according to
weight data) weight value
from max. to
F2.2 ×××××× 0 Set point 2 mini. Set weight
F2.3 ×××××× 0 Set point 3 value as need,
if no use, keep
F2.4 ×××××× 0 Set point 4
0. Note：Do not
Set point 5 set 0 as weight
F2.5 ×××××× 0 (minimum value between
weight data) set points.

- 23 -
 F3 None None No.3 parameter

Analog output：
4-20 /
4-20：4-20mA
0-20 /
0-20：0-20mA
0-24 /
0-24：0-24mA
F3.1 0-5 / 4-20
0-5 ：0-5V
0-10 /
0-10：0-10V
-5-5 /
-5-5 ：-5-5V
-10-10
-10-10 ：-10-10V

Analog output mode：

OFF ： Weight and analog
ON /
F3.2 OFF output are direct proportion；
OFF
ON：Weight and analog output
are inverse proportion.
F4 None None No.4 parameter
F4.1 00～99 01 Scale no.
1200～
F4.2 9600 Baud rate
57600
RS/RE/ RS ： GM ； RE ： CHIMEI ；
F4.3 RS
Bus Bus：MODBUS.
Communication mode:
(Available when F4.3 is
READ/
F4.4 CONT RS/RE)
CONT
READ ： command ； CONT ：
continue
Serial port data-sent
speed(Available when F4.4 is
F4.4.1 0~5 1 CONT)：
1-5 means 10-50ms;
0 means one character time.

- 24 -
 MODBUS communication
F4.4 Rtu/Asc Rtu mode (Available when F4.3 is
Bus)

MODBUS dual-byte register

storage turn(Available when
Hi F4.4 is Rtu)：
F4.4.1 Lo/Lo Hi Lo Hi Lo：High byte in the front,
Hi low byte at back ；Lo
Hi：Low byte in the front, high
byte at back.

7-E-1/
7-O-1/
7-N-2/ Data format(data bit + parity bit
F4.5 8-E-1/ 8-E-1 + stop bit) ， only the last 4
8-O-1/ format is for MODBUS.
8-N-1/
8-N-2
F5 None None No.5 parameter
OFF ： Not need stability to
adjudge whether output or not
ON/OF from set point；
F5.1 OFF
F ON：Need stability to adjudge
whether output or not from set
point.

- 25 -
 DA：Sub-display show analog
value；
SP：Sub-display show present
weight among different set
points.
If present weight<mini set
F5.2 DA/SP DA point, sub-display show weight
value at mini set point; if
present weight>set point 1,
sub-display show weight value
at set point 1; others sub-
display show nearest set point-
present weight.
F6 None None No.6 parameter
ON /
F6.1 OFF Password switch
OFF
Password setting. See
F6.2
Character 5.11 for details.
5 Operation
5.1 Operation status
1. When power on, buzzer hoot, main and sub-display
flash “8”，and instruction lights also sparkle.
2. After finished, main display
show “8806-A” ， and sub-display
show “software no. ”.
3. After 3 seconds, main display
show present weight value, andsub-
display show related setting in
Character F5.2. See Character F5.2
for details.
- 26 -
5.2 Working instrument
For examples: F2.1=SP1 、 F2.2=SP2 、 F2.3=SP3 、
F2.4=SP4、F2.5=SP5，present weight W compare with SPx
to control I/O output.
Set point
Weight I/O output
display
W>= SP1 1 SP1 output effectively
SP2<=W<SP1 2 SP2 output effectively
SP3<=W<SP2 3 SP3 output effectively
SP4<=W<SP3 4 SP4 output effectively
SP5<=W<SP4 5 SP5 output effectively
W<SP5 6 SP6 output effectively

5.3 Manual zeroing

When stop, press or input “zeroing” signal to clear
gross weight value. Note: Operation must be in stable status
or gross weight is in the zeroing range. Otherwise the
indicator will display ERROR3 or ERROR2.

- 27 -
5.4 I/O testing
Press to switch among OUT1~OUT10 and
press to return. Please refer following flow chart:

Stop

Press 5 times till main-display show“tStio”.

Sub-display indicate F
means IN1~IN4 from
Press ， left to right，when input
main-display effectively, F change to
show “inPUt” O.

For example, F changeto

O indicates IN1 input
Press to effectively and connect
enter I/O input correctly.
testing.
OUTPUT means testing.
Main-display show
Press ， output number ， sub-
main-display display show status.
show
“oUtPUt”
Press ，sub-display
OFF change to ON
indicates OUT1 output
effectively and connect
Press to
correctly.
enter I/O output Press to switch
testing.
output numbers, such
as from OUT1 to OUT2.

- 28 -
5.5 I/O definition
When stop, user can define I/O ports by and
to return.
The flow chart is to define OUT3 as O5(SP5) for
example：

When stop, press 4 times，main

display show “iodEF”.

Press to input correct

calibration password, then press
to define.

Main display show output and sub-

display show code. Press tillmain
display show OUT3.

Press till sub-display show 05，

then press to finish, and
press to return.

Output code table：

Output
Code Definition Description
O0 None No definition
Effective output when
O1 Sp 1
present weight>=set point 1.

- 29 -
 Effective output when set
O2 Sp 2 point 1 >present weight>=set
point 2.
Effective output when set
O3 Sp 3 point 2 >present weight>=set
point 3.
Effective output when set
O4 Sp 4 point 3 >present weight>=set
point 4.
Effective output when set
O5 Sp 5 point 4 >present weight>=set
point 5.

Effective output when

O6 Sp 6
present weight<set point 5.
Effective output in stable
O7 Stable
status.
O8 Zero Effective output at zero.
Effective output when
O9 Overflow
overflow.
Input
Code Definition Description

Effective input for zeroing

I1 Zeroing when weight value is stable in
the zeroing range.

Note: Same input or output code can be defined by several

inputs or output terminals, such as both of IN1 and IN2
can be defined I1 (zeroing).

- 30 -
5.6 Display testing
The following flow chart is to test lights on main-display
and sub-display, status and instruction:
Press 9 times in stop status till
main display show “tStdip”.

Press till all of lights shine

and sparkle at 2seconds/time.

Press 2 times to exit testing and

return.

- 31 -
5.7 Reset
Reset present parameters to initial setting.
Reset “I/O definition (io)” for example:

1. When stop ， press till main

display show “init”.

2. Press to input correct

calibration password.

3. Press till sub-display show

“io(I/O definition)”.
Note: “SETUP” to backup operation
parameters; “CAL” to backup
calibration parameters; “rECiPE”
to backup recipe parameters;
“ALL” to reset all of parameters.

4. Press ， sub-display show

“YES?”.

5. Press ， sub-display show

“SUCCES” to enter next parameters.
Press to return.

1. Suggestion: When reset, please backup first to be

used in the future.

- 32 -
5.8 Backup
User can make all of parameters backup.
Make“all of parameters(ALL)”backup for example:
1. When stop ， press till main
display show “bAC”. And then press

input calibration password, sub-

display show “SET UP”.

2. Press till sub-display show

“ALL (all of parameters)”
Note: “SETUP” operation
parameters backup; “CAL”
calibration parameters backup;
“io” I/O definition backup.

3. Press ， sub-display show

“YES?”, press to confirm and enter
next parameters. Otherwise press
to exit.
5.9 Restore backup
User can restore all of parameters to backup status.
Please refer backup instruction to operate, when main
display show “rbAC”, confirm and restore.
5.10 Analog calibration
Calibrate at 4 values：4mA、12mA、20mA and maximum
current.
1) 4mA：Main display shows CAL DA, sub-display 10923 ,
ID indicates 1；

- 33 -
2) 12mA：Main display shows CAL DA, sub-display 32768,
ID indicates 2；
3) 20mA：Main display shows CAL DA, sub-display 54613,
ID indicates 3；
maximum current：Main display shows CAL DA, sub-display
24.000.
For example: calibrate “12mA output” and “Max. current” :
1. When stop, press till main display
show CALdA.
2. Press to input calibration
password.
3. Press ，ID indicate from 1 to 2，
which means from 4mA to 12mA.
4. Calibrate when analog output is not
12mA by multi-meter.
Press ， sub-display sparkle ， thenpress
or to change DA digits to adjust analog
output 12mA，press tofinish.
User also can change DA digits according to
the highest digit: Press when
calibrate，then present highest digit sparkle,
so press to select and press and
in turn to change digits.
5. If ID doesn’t display, which indicate the
present value is maximum analog output,
user can input present analog value now.
6. Press to exit.
1. Press long time in calibration, sub-display
value for all of analog output restore to initial value.
- 32 -
5.11 Password
All initial passwords are ：000000。Note：Calibration
password is same password as reset, backup, restore, I/O
definition and analog calibration. Whencalibration password
changed, others also changed.
Password operation as follows：
1. Press to enter password.

2. Press to input password.

Note: If input wrong, sub-display show
“Error”, then press to input again. If
Input wrong for three times, main display
show “Error4” and self-lock, but user can
operate again when power on again.
3. Input correct password, then press
to set parameters.
5.12 Password setting
User can set password in parameters when F6.1 is“ON”.
Set operation parameters password for example:
1. Press ，main display show F6.2，then
press to enter password.
Note：If F6.1 is OFF ，user can’t enter
password when press .
2. Press and in turn to input
password.
Note：User must input same new password
twice in setting password. If not same,
main display show“Error”one second and
return to PASS again.
3. When input same new password twice,
press to save and return F6.2.
- 33 -
6 Serial port communication
Note：Not permit to change parameters related with serial
port by serial ports.
Communication protocols: RS/ RE/MODBUS, which can be
set in operation parameter F4.
6.1 RS protocol
Two modes：Continue（Cont）/Command（Read）at ASCII
code.
6.1.1 Continue (Cont)
When operation parameter F4.3 for RS、F4.4 for Cont，
indicator send weighing data to host computer without
command.
Data Format：
Scale
STX R S 000 Status +/- Value CRC CR LF
no.
Here：
STX —— 1bit，start character 02H
Scale no. —— 2bits，range at 01-99，For example: 01 is 30H
31H
R —— 1bit，52H
S —— 1bit，53H
000 —— 3bit， 30H 30H 30H
Status —— 1bit, 4DH:M(stable)；53H:S(motion) ；4FH: O
(overflow)
+/- —— 1bit，+：2B，-：2D
- 34 -
Value —— 7bits, including radix point, if no, the highest bit is
0.
CRC —— 2bits，check sum，means to add all of front digits
and transform to algorism, and then transform the last two
digits to ASCII code.
CR —— 1bit，0DH
LF —— 1bit，0AH
For example: 02 30 31 52 53 30 30 30 4D 2B 30 30 30 30 39
31 36 38 30 0D 0A
Means：1# scale stable、positive data、present weight 916.
6.1.2 Command (Read)
When operation parameter F4.3 for RS、F4.4 for Read，
indicator send weighing data to host computer after
received command.
1) Host computer read present status
Read command：

STX Scale no. R S CRC CR LF

Correct response：

Scale
STX R S 000 Status +/- Value CRC CR LF
no.

Wrong response：

STX Scale no. R S N O CRC CR LF

Here：
- 35 -
N —— 1bit，4EH
O —— 1bit，4FH
For example：02 30 31 52 53 36 34 0D 0A
Correct response：02 30 31 52 53 30 30 30 4D 2D 30 30 30
32 30 2E 30 36 36 0D 0A
Means：1# Scale、stable，Present main display -20.0。
2)Host computer read“Set point”
Read command：
STX Scale no. R Spx CRC CR LF

Correct response：

STX Scale no. R Spx DDDDDD CR CRC LF

Wrong response：

STX Scale no. R Spx N O CRC CR LF

Here：
Spx —— 1bit，1- 5 means 31H、32H、33H、34H、35H
DDDDDD —— 6bits，set point value.
Read command on set point 1 for example:
02 30 31 52 31 33 30 0D 0A
Correct response：
02 30 31 52 31 30 30 30 37 30 30 32 35 0D 0A
Means set point 1 value is 700.
3) Host computer read radix point

- 36 -
 Read command：
STX Scale no. R P CRC CR LF

Correct response：

STX Scale no. R P DDDDDD CRC CR LF

Wrong response:
STX Scale no. R P N O CRC CR LF

Here：
P —— 1bit，50H
DDDDDD —— 6bits，range at 0- 4，means radix point，for
example, 30H 30H 30H 30H 30H 34H for 4bits radix point
Read radix point for example：02 30 31 52 50 36 31 0D 0A
Correct response：
02 30 31 52 50 30 30 30 30 30 31 35 30 0D 0A
Means: 1# scale radix point 1bit.
4) Host computer read operation parameters
Read command：
STX Scale no. R F Parameters 0 CRC CR LF
Correct response：
STX Scale no. R F Parameters 0 DDDDDD CRC CR LF

Wrong response：

STX Scale no. R F N O CRC CR LF

- 37 -
Here：
F —— 1bit，46H
Parameters —— 3bits, for example: digit filter F1.5 for 31H
35H 30H
0 —— 1bit，30H
DDDDDD —— 6bits，operation parameter data
Read command operation parameter F1.5 for example:
02 30 31 52 46 31 35 30 30 34 39 0D 0A
Correct response：
02 30 31 52 46 31 35 30 30 30 30 30 30 30 34 34 31 0D 0A
Means: 1# scale F1.5 is 4.
5) Host computer write set point value
Write command：
STX Scale no. W Spx DDDDDD CRC CR LF

Correct response：

STX Scale no. W Spx O K CRC CR LF

Wrong response：

STX Scale no. W Spx N O CRC CR LF

Here：
W —— 1bit，57H
Spx —— 1bit，1- 5 means 31H、32H、33H、34H、35H

- 38 -
 DDDDDD —— 6bits，set point value
K —— 1bit，4BH
Write command set point 1 at 1500 on #1 scale for example:
02 30 31 57 31 30 30 31 35 30 30 32 39 0D 0A
Correct response ：
02 30 31 57 31 4F 4B 38 39 0D 0A
Means: #1 scale have saved written data.
6) ) Host computer write operation
parameters Write command：
STX Scale no. W F Parameters 0 DDDDDD CRC CR LF

Correct response：

STX Scale no. W F O K CRC CR LF

Wrong response：

STX Scale no. W F N O CRC CR LF

Here：
W —— 1bit，46H
Parameters —— 3bits，for example, digit filter F1.5 31H
35H 30H
O —— 1bit，30H
DDDDDD —— 6bits，operation parameter value
Write command F1.5 at 7 on #1 scale for example:

- 39 -
02 30 31 57 46 31 35 30 30 30 30 30 30 30 37 34 39 0D 0A
Correct response：02 30 31 57 46 4F 4B 31 30 0D 0A
Means: #1 scale has saved F1.5 at 7.
7）Host computer zero calibration with weights
Write command：
STX Scale no. C Z CRC CR LF

Correct response：

STX Scale no. C Z O K CRC CR LF

Wrong response：

STX Scale no. C Z N O CRC CR LF

Here：
C —— 1bit，43H
Z —— 1bit，5AH
Write command zero calibration with weights on #1 scale for
example: 02 30 31 43 5A 35 36 0D 0A
Correct response：02 30 31 43 5A 4F 4B 31 30 0D 0A
Means command has been performed correctly. 8
）Host computer zero calibration without weights
Write command：
STX Scale no. C Y DDDDDD CRC CR LF

Correct response：
- 40 -
 STX Scale no. C Y O K CRC CR LF

Wrong response：

STX Scale no. C Y N O CRC CR LF

Here：
Y —— 1bit，59H
DDDDDD —— 6bits，related zero millivolt，fixed 3bit radix
point.
For example：Send 1.500mA as zero calibration to #1 scale
02 30 31 43 59 30 30 31 35 30 30 34 39 0D 0A
Correct response：02 30 31 43 59 4F 4B 30 39 0D 0A
Means data has been saved in #1 scale.
9）Host computer calibrate radix point
Write command：
STX Scale no. C P Radix point CRC CR LF

Correct response：

STX Scale no. C P O K CRC CR LF

Wrong response：

STX Scale no. C P N O CRC CR LF

Here：
P —— 1bit，59H

- 41 -
Radix point —— 1bit，range at 0~4
For example: calibrate radix point 3 on #1 scale
02 30 31 43 50 33 39 37 0D 0A
Correct response: 02 30 31 43 50 4F 4B 30 30 0D 0A
Means: Data has been saved in #1 scale.
10） Host computer calibrate minimum division and
maximum capacity
Write command：
STX Scale no. C M DD DDDDDD CRC CR LF

Correct response：

STX Scale no. C M O K CRC CR LF

Wrong response：

STX Scale no. C M N O CRC CR LF

Here：
M —— 1bit，4DH
DD —— 2bits，division 1、2、5、10、20、50
DDDDDD —— 6bits，maximum capacity
For example: Send division 1 and maximum capacity 10000
to #1 scale.
02 30 31 43 4D 30 31 30 31 30 30 30 30 32 39 0D 0A
Correct response：02 30 31 43 4D 4F 4B 39 37 0D 0A

- 42 -
 Means: Data has been saved in #1 scale.

11） Host computer gain calibration with weights

Write command：
STX Scale no. C G DDDDDD CRC CR LF

Correct response：

STX Scale no. C G O K CRC CR LF

Wrong response：

STX Scale no. C G N O CRC CR LF

Here：
G —— 1bit，47H
DDDDDD —— 6bits，weights value
Send command gain calibration to #1 scale for example:
02 30 31 43 47 30 31 30 30 30 30 32 36 0D 0A
Correct response: 02 30 31 43 47 4F 4B 39 31 0D 0A
Means: Written 10000 have been saved in #1 scale.
12）Host computer gain calibration without weights
Write command：
Scale
STX C L D1D1D1D1D1D1 D2D2D2D2D2D2 CRC CR LF
no.

Correct response：

- 43 -
 STX Scale no. C L O K CRC CR LF

Wrong response：

STX Scale no. C L N O CRC CR LF

Here：
L —— 1bit，4CH
D1D1D1D1D1D1 —— 6bits，gain millivolt
D2D2D2D2D2D2 —— 6bits，weight value
For example：Calibrate 4.110mA as 10000
02 30 31 43 4C 30 30 34 31 31 30 30 31 30 30 30 30 32 35
0D 0A
Correct response：02 30 31 43 4C 4F 4B 39 36 0D 0A
Means：Written data has been saved in #1 scale.
13）Host computer zeroing operation
Write command：
STX Scale no. C C CRC CR LF

Correct response：

STX Scale no. C C O K CRC CR LF

Wrong response：

STX Scale no. C C N O CRC CR LF

Zeroing operation on #1 for example：
02 30 31 43 43 33 33 0D 0A
- 44 -
Correct response：02 30 31 43 43 4F 4B 38 37 0D 0A
Means zeroing operation has been performed correctly.
6.2 RE protocols
Two modes：Continue (Cont)/ command (Read).
Support all of data format in parameters F4.5; ASCII code.
6.2.1 Continue mode (Cont)
When operation parameters F4.3 for RE、F4.4 for Cont，
indicator send data to host computer without any command.
Data format as follows:
Status ， GS ， Sign Value Unit CR LF
Here：
Status —— 2bits，OL：( 4FH 4CH ) overflow；ST：( 53H
54H )stable US：( 55H 53H )unstable
， —— 1bit，list separator 2CH
GS —— 2bits，47H 53H
Sign —— 1bit，2BH（+）
、2DH（-）
Value—— 7bits，including decimal point，if no, the highest bit
is 0
Unit —— 2bits，Kg 4BH 67H
CR —— 1bit，0DH
LF —— 1bit，0AH
For example：Indicator sends following data format:
53 54 2C 47 53 2C 2B 30 31 31 2E 31 32 30 4B 67 0D 0A
Means ：stable、positive data、present weight value is 11.
120kg
- 45 -
6.2.2 Command mode (Read)
When operation parameters F4.3 for RE、F4.4 for Read，
indicator send present data to host computer only after
received command .
Data format as follows:
R E A D CR LF

Here：
R —— 52H
E —— 45H
A —— 41H
D —— 44H
CR —— 0DH
LF —— 0AH
Response data format is same as data format in continue
mode.
For example
Command： 52 45 41 44 0D 0A
Response： 53 54 2C 47 53 2C 2B 30 31 31 2E 31 32 30 4B
67 0D 0A
Means：stable、positive data、present weight value is 11.
120kg.

- 46 -
6.3 MODBUS protocol
6.3.1 Communication mode
MODBUS communication by two mode：RTU and Asc。
When parameter F4.4 is RTU，every 8-bit byte of the
message are divided into 2pcs of 4-bit hexadecimal
characters to transmit at binary code. Data format：8- E-1，
8- O-1，8- n-1，8- n-2。
When parameter F4.4 is ASCII，every 8-bit byte of the
message is transmitted as 2pcs ASCII characters at ASCII
code, which can support all of data format in parameter F4.5.
6.3.2 MODBUS communication address
PLC Display
Description
address address
The following items are only-read register(code 0x03)
40001 0000 Present weight value(4bits including
sign characters, the high bit is in the
40002 0001 front)
D0（0 stable、1 unstable）；D1（0
normal 、 1 overflow ）； D2 （ 0
none-zero、1 zero）
D4（0 positive sign、1 negative sign）；
D5 （ 0 sp1 ineffective 、 1 sp1
40003 0002 effective）；D6（0 sp2 ineffective、1
sp2 effective）；D7（0 sp3 ineffective、
1 sp3 effective ）； D8 （ 0 sp4
ineffective、1 sp4 effective）
；
D9 （ 0 sp5 ineffective 、 1 sp5
effective） ；D10（0 sp6 ineffective、1
sp6 effective）；
- 47 -
 40004 0003
Reserve(permit to read, reading
…... ……
value is 0 )
4007 0006
The following items are two bytes and are available to read
and write (write code 0x06，read code 0x03）
Automatically zeroing when power on.
40008 0007 （F1.1）

40009 0008 Zero tracking range（F1.2）

40010 0009 Zeroing range（F1.3）
40011 0010 Stable range（F1.4）
40012 0011 Digit filter parameters(0-9)（F1.5）
40013 0012 Stability filter series(0-9)（F1.6）
40014 0013 Analog output mode（F3.1）
40015 0014 Analog inverting input（F3.2）
40016 0015 I/O output stability（F5.1）
40017 0016 Sub-display items（F5.2）

40018 0017 Reserve （ read value 0 ， no any

…… …… operation when write. Suggest had
40021 0020 better not write in order to update in
the future. ）
40022 0021 Radix point（0- 4）
Minimum division（ 0- 5 means 1/ 2/ 5/
40023 0022
10/ 20/ 50）
Load cell sensitivity （ 0- 1 means
40024 0023 2mV/V、3mV/V）
40025 0024 Reserve （ read value 0 ， no any
…… …… operation when write. Suggest had
40034 0033 better not write in order to update in
the future. ）
- 48 -
 The following items are four bytes and available to read
and write(writing code 0x10，read code 0x03）
Maximum
0031-0032 0030-0031 capacity(max.capacity≤mini.
division×30000)
Zero calibration with weights
Write 0001H to take present
weight as zero when weight
0033-0034 0032-0033 value is stable；
Return present millivolt at
zero when read.
Gain calibration with weights
Write present weight value
according to present millivolt；
40035-40036 0034-0035 Return present millvolt at
present weight value when
read.
Zero calibration without
weights
40037-40038 0036-0037 Write millivolt value at zero；
Return present millivolt value
at zero when read.
Gain calibration without
weights, input gain millivolt.
Write gain millivolt value
40039-40040 0038-0039 related gain weight, indicator
save first；
Return millivolt value related
present weight when read.
Gain calibration without
weights，input gain weight
value（≤maximum capacity）.
Write weight value related
40041-40042 0040-0041 gain millivolt after writing gain
millivolt first, gain calibration
in this register by both of
weight and millivolt；
Return 0000H when read.
- 49 -
40043-40044 0042-0043 Set point numbers
40045-40046 0044-0045 Set point 1（F2.1）
40047-40048 0046-0047 Set point 2（F2.2）
40049-40050 0048-0049 Set point 3（F2.3）
40051-40052 0050-0051 Set point 4（F2.4）
40053-40054 0052-0053 Set point 5（F2.5）
Upper limit（F2.2）only for 3
40055-40056 0054-0055
set points.
Moderate limit （F2.3） only
40057-40058 0056-0057
for 3 set points.
Lower limit （F2.4）only for 3
40059-40060 0058-0059
set points.
The following items are bit read only. （read code：0 x 0 1）
00057 0056 0：Stable； 1：Unstable
00058 0057 0：Normal； 1：Overflow
00059 0058 0：None-zero； 1：Zero
00060 0059 0：Positive sign；1：negative sign
SP1 output effective（0 ineffective；1
00061 0060
effective）
SP2 output effective（0 ineffective；1
00062 0061
effective）
SP3 output effective（0 ineffective；1
00063 0062
effective）
SP4 output effective（0 ineffective；1
00064 0063
effective）
SP5 output effective（0 ineffective；1
00065 0064
effective）

- 50 -
 SP6 output effective（0 ineffective；1
00066 0065 effective）

00067 0066 Reserve （ read value 0 ， no any

operation when write. Suggest had
….. ….. better not write in order to update in the
00075 0074 future. ）
The following item are available to read and write
（read code：0x01，writing code： 0x05）
Zeroing (write FF00)；read to return
00076 0075 fixed 0
6.3.3 Function code
Above Modbus communication protocols have five function
codes：01 read coil、03 read register、05 force single coil、
06 preset single register、16( 10 Hex) preset several
registers.
◆ 01 read coil
Inquiry：Regulate coil start and quantities.
Response：
a) Every coil state in response message is corresponding
to every data in data area；1=ON；0=OFF。The LSB in
first byte is start address in inquiry. Other coils are in
seriation from lowest to highest in the byte till full of 8pcs,
next byte same seriation.
b) If they are not 8 multiples, the last byte is full of zero from
the remain to the highest，which byte sections indicate
all of byte quantities.

- 51 -
For example：Inquiry weighing indicator 01 to read 40- 43 coil
1） RTU communication mode：
Inquiry command：
Function Start Coil CRC
Address
code address quantity parity
1byte 1byte 2byte 2byte 2byte
Correct response：
Function Account CRC
Address code byte Data area parity
1byte 1byte 1byte 1byte 2byte

Inquiry command：01 01 00 28 00 04 BD C1
Correct response：01 01 01 02 D0 49（Coil 43- 40 related
state：0- 0- 1- 0）
2） ASCII communication mode：
Inquiry command：
Function Start Coil LRC
Start Address Stop
code address quantities parity
1byte 2byte 2byte 4byte 4byte 2byte 2byte
Correct response：
Function Account Data LRC
Start Address Stop
code byte area parity
1byte 2byte 2byte 2byte 2byte 2byte 2byte

Inquirycommand:3A 30 31 30 31 30 30 32 38 30 30 30 34 44
32 0D 0A
Correct response：3A 30 31 30 31 30 31 30 32 46 42 0D 0A
（Coil 43- 40 related status：0- 0- 1- 0）
- 52 -
 ◆ 03 read register
Inquiry：Regulate to read register start address and register
quantities.
Response：Regulate read register byte quantities, every
register relate 2bytes respectively；Message also has data
from every read register.
For example：read register 0007、0008。
1） RTU communication mode：
Inquiry command：
Inquiry
Function Start CRC
Address register
code address parity
quantity
1byte 1byte 2byte 2byte 2byte
Correct response：
Function Account Register Register CRC
Address
code byte (0007) data (0008) data parity
1byte 1byte 1byte 2byte 2byte 2byte
Inquiry command：01 03 00 07 00 02 75 CA
Correct response：01 03 04 00 00 00 05 3A 30（Register
0007、0008 respective data：0（Hex：0000H）、5（Hex：
0005H）
2） ASCII communication mode：
Inquiry command：
Inquiry
Function Start LRC
Start Address register Stop
code address parity
quantity
1byte 2byte 2byte 4byte 4byte 2byte 2byte
- 53 -
 Correct response：
Register
Function Account Register LRC
Start Address (0007) Stop
code byte (0008) data parity
data
1byte 2byte 2byte 2byte 2byte 2byte 2byte 2byte

Inquirycommand:3A 30 31 30 33 30 30 30 37 30 30 30 32 46
33 0D 0A
Correct response：3A 30 31 30 33 30 34 30 30 30 30 30 30
30 35 46 33 0D 0A（register 0007、0008 respective data ：
0（Hex：0000H）、5（Hex：0005H）
◆ 05 force single coil
Force：Regulate force coil address；and one normal item in
force data area，regulate requested coil ON/ OFF state: FF00
for ON，0000H for OFF，other data is ineffective to coil.
Response：Return normal response for force coil.
For example：Force weighing indicator 01, 0056 coil is ON
1）RTU communication mode：
Force command：
Function Coil CRC
Address Force data
code address parity
1byte 1byte 2byte 2byte 2byte
Correct response：
Function Coil CRC
Address Force data
code address parity
1byte 1byte 2byte 2byte 2byte
- 54 -
Force command：01 05 00 38 FF 00 0D F7
Correct response：01 05 00 38 FF 00 0D F7（Coil 0056 is
ON）
2）ASCII communication mode：
Force command：
Function Coil Force LRC
Start Address Stop
code address data parity
1byte 2byte 2byte 4byte 4byte 2byte 2byte
Correct response：
Function Coil Force LRC
Start Address Stop
code address data parity
1byte 2byte 2byte 4byte 4byte 2byte 2byte
Force command：3A 30 31 30 35 30 30 33 38 46 46 30 30 43
33 0D 0A
Correct response：3A 30 31 30 35 30 30 33 38 46 46 30 30
43 33 0D 0A（Coil0056 is ON）
◆ 06 preset single register
Preset：Regulate to preset single register address and data.
Response：Return normal response after register is preset.
For example：Request 0009 register in weighing indicator 01
is preset 0005H
1） RTU communication mode：
Preset command：
Function Preset register Preset CRC
Address
code address data parity
1byte 1byte 2byte 2byte 2byte
- 55 -
Correct response：
Function Preset register Preset CRC
Address
code address data parity
1byte 1byte 2byte 2byte 2byte

Preset command：01 06 00 09 00 05 99 CB
Correct response：01 06 00 09 00 05 99 CB（register 0009data：5
（Hex：0005H）
）
2） ASCII communication mode：
Preset command：
Preset
Function Preset LRC
Start Address register Stop
code data parity
address
1byte 2byte 2byte 4byte 4byte 2byte 2byte
Correct response：
Preset
Function Preset LRC
Start Address register Stop
code data parity
address
1byte 2byte 2byte 4byte 4byte 2byte 2byte

Preset command: 3A 30 31 30 36 30 30 30 39 30 30 30 35
45 42 0D 0A
Correct response：3A 30 31 30 36 30 30 30 39 30 30 30 35
45 42 0D 0A（register 0009 data： 5（Hex：0005H））
◆ 16（10 hex） Preset several registers
Preset：Regulate to preset register start address and preset
value.

- 56 -
 Response：Return address, function code, start address and
preset register quantity.
For example：Preset 2 registers in weighing indicator 01:
start register is 0030. Preset value is 0001H and 7318H 1
）RTU communication mode：
Preset command：
Function Start Register Account Preset CRC
Address
code address quantity byte data parity
1byte 1byte 2byte 2byte 1byte 4byte 2byte
Correct response：
Function Start Register CRC
Address
code address quantity parity
1byte 1byte 2byte 2byte 2byte

Preset command：01 10 00 1E 00 02 04 00 01 73 18 07 D5
Correct response：01 10 00 1E 00 02 21 CE
2）ASCII communication mode：
Preset command：
Function Start Register Account Preset LRC
Start Address Stop
code address quantity byte data parity
1byte 2byte 2byte 4byte 4byte 2byte 8byte 2byte 2byte
Correct response：
Function Start Register LRC
Start Address Stop
code address quantity parity
1byte 2byte 2byte 4byte 4byte 2byte 2byte

Preset command：3A 30 31 31 30 30 30 31 45 30 30 30 32
- 57 -
30 34 30 30 30 31 31 43 39 36 31 38 0D 0A
Correctresponse:
3A 30 31 31 30 30 30 31 45 30 30 30 32 43 46 0D 0A
6.3.4 MODBUS communication error message
When weighing indicator check other error message except
parity code( CRC or LRC)，indicator will send message to
host computer, the highest in function code is 1，which
means function code from weighing indicator to host
computer is added 128 based on function code from host
computer(For example: read register command 03H will be
changed to 83H).
Error code:
02: error data address；Received data address is not
permitted by weighing indicator.
03: error data；Inquiry data is not permitted by weighing
indicator.
For example：Host computer read coil (0040) by function
code 03.
Error message format：
1） RTU communication mode：
Address Function code Error code CRC parity
1byte 1byte 1byte 2byte
2） ASCII communication mode：

- 58 -
 Function Error LRC
Start Address Stop
code code parity
1byte 2byte 2byte 2byte 2byte 2byte

1） RTU communication mode：

Inquiry command：01 03 00 28 00 01 04 02
Error response：01 83 02 C0 F1 2
） ASCII communication mode：
Inquiry command：3A 30 31 30 33 30 30 32 38 30 30 30 31
44 33 0D 0A
Error response：3A 30 31 38 33 30 32 37 41 0D 0A
From response message, the present error code is 02, which
means the present received data address is error, not permit
by weighing indicator.

7 Error and alarm message

ERROR ：Input wrong data beyond parameter range.
ERROR2：The present weight value is out of zeroing range.
ERROR3：Scale platform is not stable in zeroing.
ERROR4：Input wrong password more than 3 times.
OVER ：The load cell sign is too big in zero calibration.
UNDER ：The load cell sign is too small in zero calibration.
OFL ：Overflow

- 59 -