OWNER'S

MANUAL
YETI SB100
 TABLE OF CONTENTS
BRAND OVERVIEW 03

FRAME FEATURES 05

GEOMETRY 07

MAINTENANCE SCHEDULE 09

TECHNICAL

ASSEMBLY OVERVIEW 11

EXPLODED VIEWS 17

REBUILD KITS 21

LEGAL

WARRANTY 23

CONTACT INFORMATION 24

1. 2.
 CONGRATULATIONS ON YOUR
PURCHASE OF A NEW YETI.
WELCOME TO THE TRIBE.
We are confident your new bicycle will exceed This manual outlines basic setup and
your expectations for value, performance, and maintenance recommendations of your new
ride quality. Each frameset and component Yeti. Because it is impossible to anticipate
has been custom specified and designed to every situation or condition that may occur
enhance your riding experience. Whether you during the assembly, setup, and maintenance
are a beginner cyclist, or a seasoned pro, of your bicycle, Yeti recommends that all
your Yeti bicycle will provide endless hours of service and repairs be performed by your
two-wheeled fun. local authorized Yeti Dealer.

This model specific manual is designed to This manual contains many “Warnings” and
be used in conjunction with the general Yeti “Cautions” concerning the consequences
Owner’s Manual and the manuals supplied by of failure to maintain or inspect your bicycle.
the suspension manufacturers. If you did not The word “Warning” indicates a potentially
receive the Yeti owner’s manual or the manual hazardous situation in which , if not avoided,
provided by the suspension manufacturer, could result in serious injury or death. The
download the materials off the Internet, or word “Caution” indicates a potentially
contact your local dealer. hazardous situation in which, if not avoided
may result in minor injuries or damage to
Bicycling can be a hazardous activity your bicycle or a component of your bicycle.
even under the best of circumstances. Be sure to read and understand all of the
Proper maintenance of your bicycle is your Warnings and Cautions listed in the manual.
responsibility and when done properly helps
reduce the risk of injury and damage to your
bicycle.

Warning: Make sure you review and understand the warnings, instructions, and content of this manual and accompanying
manuals for your bicycle.

Warning: Technological advances have made bicycles and bicycle components more complex and the pace of innovation is
increasing. It is impossible for this manual or the accompanying manuals to provide all the information required to properly
repair and/or maintain your bicycle. In order to help minimize the chances of an injury, it is critical for you to have work
performed by an authorized Yeti retailer.

3. 4.
 THE LOWDOWN 1. The SB100 delivers 100mm of travel with our patented Switch
Infinity Technology that has been redesigned for this short travel

THE SB AND ITS

frame. Efficient pedaling performance while still smooth and
continuous when the going gets rough.

FEATURES.
1. PATENTED SWITCH INFINITY SUSPENSION SYSTEM REDESIGNED FOR 100MM OF TRAVEL
2.

3.
Top of the top Turq Series frames and our Carbon series both offer
the same geometry and efficiency in all models.

The SB100 does away with the front derailleur mount, making it a 1x
drive specific frame. This increases stiffness in the frame, making
2. HIGH MODULUS CARBON FIBER MAIN FRAME AND SWING ARM
the SB100 one of the stiffest bikes in our lineup.
3. INTEGRATED 2-BOLT ISCG-05 MOUNTS
4. 2 bolt ISCG 05 chain guide mounts are included on the SB100 in
4. TAPERED INTEGRATED HEADTUBE (41MM / 52MM)
case you want to go for some extra drivetrain security for the rowdy
5. CUSTOM DOWN TUBE PROTECTOR AND CHAIN GUARDS sections.

6. INTERNALLY MOLDED CARBON TUBES INSIDE OF FRAME FOR HASSLE-FREE CABLE ROUTING
5. The SB100 uses an integrated 41mm / 52mm tapered headset. This
7. INTEGRATED AXLE AND DERAILLEUR HANGER SYSTEM
system allows for the headset bearings to be contained inside the
8. BOOST HUB SPACING, FRONT AND REAR head tube for an overall lower ride height, more simplified
installation, and increased stiffness.
9. CUSTOM SWITCH INFINITY FENDER

10. CLEARANCE FOR STANDARD SIZED WATER BOTTLE INSIDE MAINFRAME 6. The SB100 uses a 37.5mm stroke, 190mm eye to eye Float DPS
shock, by Fox Racing Shox.
11. UNINTERRUPTED SEAT TUBE FOR COMPATIBILITY WITH LONGER TRAVELED DROPPER POSTS
7. Custom guards on the seat stay, chain stay and down tube keep
things quiet while riding and protect the frame.

8. The SB100 features internally molded routing tubes for all cables,
making the bike quiet and clean looking as well as reducing
maintenance and cable rub.

9. Dedicated 12 x 148 Boost dropouts and integrated hanger with axle

threads for strength, stiffness, ease of hanger and wheel installation.

5. 6.
 GEOMETRY M
B
I FOX 34 / 1 0MM FORK
SM MD LG XL

A WHEEL 29” 29” 29” 29”

L
B REACH 407.1 432.1 452.1 472.1

C EFF. TOP TUBE 576.7 605.2 630.3 657.2

D STACK 602 612.1 627.1 647.2

E HEAD TUBE LENGTH 96.2 107 123.2 144.7

A
J F SEAT TUBE LENGTH 393 419 457 495

G EFF. SEAT TUBE ANGLE 74.3 74.2 74.1 74

H HEAD TUBE ANGLE 67.8 67.8 67.8 67.8

D
I MECH. TRAIL 96 95.9 95.9 95.9

J BB DROP 37.9 37.9 38 38

C
K EST. BB HEIGHT 332.1 332.1 332 332

L CHAINSTAY LENGTH 437 437 437 437

H K
M FRONT-CENTER 685.2 714.2 740.0 768.3
E N
N WHEELBASE 1122.3 1151.4 1177.4 1205.5
F O STAND OVER 724 724 723.9 723.9
G P AXLE TO CROWN 530.2 530.2 530.2 530.2

Q FORK OFFSET 44 44 44 44
*All measurements are in millimeters
FIT
X-SMALL 4’11” (150 CM) - 5’3” (160 CM)

SMALL 5’3” (160 CM) - 5’7” (170 CM)

MEDIUM 5'7" (170 CM) - 5'11" (180 CM)

LARGE 5'11" (180 CM) - 6'3" (191 CM)

X-LARGE 6'3" (191 CM) - 6'6" (198 CM)

7. 8.
 KEEP YOUR YETI FRESH
AND CLEAN
OVERVIEW TORQUE
Following these guidelines will help maintain the performance of your bicycle and prevent Yeti strongly recommends using a torque wrench when assembling your frame. Torque
more serious problems from arising. It is important to remember that service intervals can vary specifications for individual parts on the SB100 are listed below, as well as in the step by
depending on climate, trail conditions and riding frequency. If you are unsure about working on step assembly instructions later in the manual. For general bicycle maintenance please
your own bicycle, contact your authorized Yeti Dealer for more information on general bicycle consult the torque specifications of the component you are adjusting.
maintenance.

WEEKLY

MONTHLY

3 MONTHS

ANNUALLY
SCHEDULE KEY TORQUE SPECS
PART NUMBER DESCRIPTION TORQUE (NM)
CLEAN AND LUBE CHAIN
300030295 SHOCK BOLT, 8MM, FLAT HEAD 10
CHECK TIRE PRESSURE
300030156 SHOULDER BOLT, M6X1 FH, TI 12.5 - 14
CLEAN BIKE OF MUD AND DEBRIS
200020313 PIVOT HARDWARE, MAIN, 17MM 46
CHECK BRAKE FUNCTION
300030294 SS PIVOT BOLTS , 15MM 37
CHECK SHOCK PRESSURE
300030293 BOLT, LINK PIVOT,MALE 15MM 15
CHECK FOR LOOSE BOLTS AND TIGHTEN, IF NECESSARY
100425006 AXLE, YETI BOLT ON, 12X148MM 12-15
CHECK HEADSET AND TIGHTEN / LOOSEN, IF NECESSARY

THOROUGHLY CLEAN PIVOT POINTS WITH A RAG (DO NOT LUBRICATE)

LUBE INFINITY LINK EVERY 40 HRS. (YETI HEAVY MOLYBDENUM GREASE)

CHECK / REPLACE BRAKE PADS

CHECK TIRES FOR WEAR

CHECK SPOKE TENSION. RETENTION, IF NECESSARY

CHECK CHAIN FOR WEAR. REPLACE IF NECESSARY

COMPLETE TUNE-UP PERFORMED BY AN AUTHORIZED YETI DEALER

9. 10.
 FRAME ASSEMBLY
YETI TIPS TOOLS NEEDED
Make sure your tools are in good condition. • 2.5mm allen key
A worn allen key can round the hex on a bolt • 5mm allen keys
not allowing for proper torque. • 6mm allen key
• 8mm allen key
Torque settings are listed throughout the • T25 allen key
instructions and on page 13 of this manual. • Guide pin tool (2)
It is important to prep all bolt threads. The • Torque wrench 01. 02.
instructions denote whether to use a Loctite • Cassette tool
All the parts you’ll need to get your Install 2x Bearing Lockrings (200020311)
compound or grease. • Flat head screw SB100 frame assembled. Please refer into the SS Pivots on the Rear Triangle.
driver to the exploded view later in this manual
• Grease for more information. *Torque: 20 Nm
Warning: Service on Yeti bicycles requires special knowledge • Blue (243) Loctite
and tools. Yeti Cycles recommends that all service and
repairs be performed by an authorized Yeti Dealer

03. 04.
Install one Grease Zerk (200020314) into Install 2x H20 Bolts (300030010) and
each Main Pivot bolt with a flat head Washers to front triangle.
screwdriver. Zerk end should be flush with
the end of the Main Pivot bolt. *Torque: 4-5 Nm

11. 12.
ASSEMBLY ASSEMBLY

0. 06. 0. .
Push the SB100 Switch Infinity Link into Use a guide pin to line up the shaft eyelet Use a ball-end wrench to prevent the inner Apply a light coat of grease to the shaft of
the frame holes with the frame. Ti Female Bolts from rotating. Torque the 4x the Female Link Pivot Bolt (300030292).
Flat Head Ti Male Bolts to 12.5 - 14 Nm. Slide the Alloy Link onto the Front Triangle
and install the Female Link Pivot Bolt.

0 . . 11. 12 .
Install a short Ti Female Bolt (300030301) Install a Flat Head Male Ti Bolt Install Male Link Pivot Bolt (300030293). Install the rear shock eyelet into the Link.
from the inside of the shaft eyelet through (300030156) through the Front Triangle into Female Link Pivot Bolt. Make sure that the shock controls are facing
the frame. Use a guide pin to help into the Ti Female Bolts. Repeat for all downwards, and secure with guide pins
installation if necessary. Repeat for all four four locations *Torque to 15 Nm (note they will not pass through the frame).
mounting holes.

13. 14
ASSEMBLY ASSEMBLY

1 3. 14. 1 . 1 .
Grease heads of 2X Shock Bolt (300030295). Install front Shock Bolt. With a needle-type grease gun, fill grease Clip the Switch Infinity Fender (400100194)
Install Shock Bolt into the rear shock eyelet. into the Main Pivot Grease Zerks until a small onto the four switch infinity mounting bolts.
*Torque: 10 Nm amount of grease is purged through the Orient the fender so the small raised lip on the
*Torque: 10 Nm Switch Infinity seals. Clean off any excess backside is at the top
grease with a clean cloth or rag.

1 . 1 . 1 .
Slide the Rear Triangle over the Main Pivot Install 2x Seat Stay Pivot Bolts Apply grease to the outside circumference of
onto the Switch Infinity Link. Secure with 2x (300030294) through the Swingarm the Derailleur Hanger (300060073). Install
Main Pivot Bolt (200020313). and into the Link. onto the rear triangle. Hanger threads are
REVERSE THREADED.
*Torque: 46 Nm *Torque: 37 Nm
*Torque: 10 Nm

15. 16.
 1.2

EXPLODED VIEW
4

5.1 1.4

6.7

1.3

2.6

2.5 6.11
6.6
5.2

6.8

6.4 1.6
2.4 6.6

6.5

2.1 6.9
3 1.5
6.11

6.5

6.9

6.4

PREP KEY

6.10

LOCTITE NYLO N
PATCH
6.1 GREASE

2.3
2.2

2.7

17 18.
 EXPLODED VIEW PARTS LIST
ITEM# PART # DESCRIPTION QTY ITEM# PART # DESCRIPTION QTY

1 N/A SB100 FRONT TRIANGLE ASSEMBLY 6.4 200020313 PIVOT HARDWARE, MAIN, 17MM PYRAMID HEAD 2

1.1 N/A SB100 FRONT TRIANGLE 1 6.5 200020314 GREASE ZERK, FOX 2

1.2 300070006 ICE AXE HEAD BADGE 1 6.6 300030294 BOLT, SS PIVOT, 15MM 2

1.3 400100173 SB100 DT PROTECTOR 1 6.7 300030292 STUD, LINK BEARING, FEMALE 15MM 1

1.4 300060072 YETI SEAT CLAMP STANDARD 1 6.8 300030293 BOLT, LINK PIVOT, MALE 15MM 1

1.5 300030010 BOLT-CAP H20 (M5 X 0.8 X 16MM) 2 6.9 300030156 SHOULDER BOLT, M6X1 FH, TI 4

1.6 300030148 WASHER, 5.1X8.9X1MM 2 6.10 300030301 BOLT, TI FEMALE 8.0 X 11.75MM 4

2 N/A SB100 SWING ARM ASSEMBLY 1 6.11 300030295 SHOCK BOLT, 8MM, FLAT HEAD 2

2.1 N/A SB100 SWINGARM 1

2.2 400100174 SB100 CS/SS PROTECTOR 1

2.3 400100175 SB100 CS LOWER PROTECTOR 1

2.4 300020001 BEARING, 17X30X7, 6903-2RS MAX 2

2.5 300020052 BEARING, 15X28X7/10 LLU MAX-E 2

2.6 200020311 LOCKRING, SS PIVOT 2

2.7 300060073 12X148 HANGER STD KIT GEN3 1

3 00787 FOX LINEAR BEARING 74.0MM ASSEMBLY

4 N/A SHOCK ASSEMBLY SB100

4.1 N/A FOX FLOAT DPS 190X37.5MM 1

4.2 N.A FOX MOUNT KIT 25.0MM 1

5 N/A SB100 LINK ASSEMBLY 1

5.1 300040499 SB100 LINK - ALLOY 1

5.2 300020052 BEARING, 15X28X7/10 LLU MAX-E 2

6 N/A SB100 ASSEMBLY PARTS

6.1 400100194 FENDER, SWITCH INFINITY INT CLIP 1

19. 20.
 REBUILD KITS
PART # DESCRIPTION QTY PART # DESCRIPTION QTY

200020316 SB100 MASTER REBUILD KIT 200020318 SB100 HARDWARE REBUILD KIT
200020311 LOCKRING, SS PIVOT 2 200020311 LOCKRING, SS PIVOT 2
200020313 PIVOT HARDWARE, MAIN, 17MM PYRAMID HEAD 2 2 200020313 PIVOT HARDWARE, MAIN, 17MM PYRAMID HEAD 2 2
200020314 GREASE ZERK, FOX 2 200020314 GREASE ZERK, FOX 2
300030301 BOLT, TI FEMALE 8.0 X 11.75MM 4 300030301 4
BOLT, TI FEMALE 8.0 X 11.75MM
300020001 BEARING 6903 MAX 2 300030156 4
SHOULDER BOLT, M6X1 FH, TI
300020052 BEARING 6902 LLU MAX-E 4 300030289 BOLT, TI STUD 8.0X49.0MM 2
300030156 SHOULDERBOLT, M6X1 FH, TI 4 300030292 STUD, LINK BEARING, FEMALE 15MM 1
300030289 BOLT, TI STUD 8.0X49.0MM 2 300030293 BOLT, LINK PIVOT, MALE 15MM 1
300030292 STUD, LINK BEARING, FEMALE 15MM 1 300030294 BOLT, SS PIVOT, 15MM 2
300030293 BOLT, LINK PIVOT, MALE 15MM 1 300030295 SHOCK BOLT, 8MM, FLAT HEAD 2
300030294 BOLT, SS PIVOT, 15MM 2 400100194 FENDER, SWITCH INFINITY INT CL 1
300030295 SHOCK BOLT, 8MM, FLAT HEAD 2

400100176 FENDER, SWITCH INFINITY G2 1 400100147 PROTECTOR KIT SB100

400100173 SB100 DT PROTECTOR 1

200020317 SB100 BEARING REBUILD KIT 400100174 SB100 CS/SS PROTECTOR 1

300020001 BEARING 6903MAX 2 400100175 SB100 CS LOWER PROTECTOR 1

300020052 BEARING 6902 LLU MAX-E 4

400100179 SB100 PROTECTOR SHEET - GLOSS 1

400100176 SB100 INFINITY COVER KIT 400100180 SB100 PROTECTOR SHEET - MATTE 1
400100194 FENDER, SWITCH INFINITY INT CLIP 1

21. 22.
 WARRANTY
DISCLAIMER
HERE’S EVERYTHING YOU NEED TO KNOW ABOUT OUR LIFETIME WARRANTY: YETI Cycles is not responsible for any damages to you or others arising from riding,
transporting or other use of your bicycle. In the event that your frame breaks or malfunctions,
All 2019 (or newer) frames, including the Switch Infinity, are covered for life against damage YETI Cycles shall have no liability or obligation beyond the repair or replacement of your frame
due to manufacturing defects for the original purchaser. Paint and finish are covered for 1-year. pursuant to the terms outlined in the warranty.
We will repair or replace, at our discretion, any frame we deem defective. There are a few
conditions: you must register it online at YetiCycles.com and you must take it to an authorized
*If you have a warranty concern, please contact your authorized Yeti dealer.
Yeti Cycles dealer for processing. Warranty does not cover damage due to ordinary wear and
tear, neglect or intentional destruction. From a slingshot or your truck.

If you happen to have a crash or non-warranty situation, we’ll get you back on the trail with a
reasonable replacement price. Same conditions as above.

Lifetime Warranty applies to all 2019 and newer frames (including the SB100). Model year 2018
and older frames will be covered under our previous warranty (5-year or 2-year based on time
of purchase).

Simple as that. No fine print.

YETI CYCLES BUSINESS HOURS

621 Corporate Circle, Unit B Monday-Friday
Golden, CO 80401 8AM-11:30AM, 1:00PM-5:30PM
(p) 303-278-6909 (Mountain Time)
(f) 303-278-6906
www.yeticycles.com

23. 24.