Electronic Devices and Circuits

(EL-1004)
LABORATORY MANUAL
FALL 2023

(LAB # 01)
Familiarization to Proteus and Lab Equipment

Engr. Kashif Ullah Khattak

Student Name: __Muhammad _Ahmed_Khan

Roll No: __22I-2200____ Section: ______A____

Date performed: __________________________

Manual Submission Date: __________________

______________________________________________________________________________________________________________________________________________________

NATIONAL UNIVERSITY OF COMPUTER AND EMERGING SCIENCES, ISLAMABAD

Prepared by: Engr. Naveed Iqbal Version: 2.14

Last Edited by: Engr. Maria Nasir Updated: Fall 2023
Verified by: Dr. Rashad Ramzan
Electronic Devices National University Roll No: __________ L
& Circuits
(EL-1004)
of Computer and Emerging Sciences
Islamabad
a
b
#
01
_________________________________________________________________________________

01 _______________________________
LAB ENGINEER SIGNATURE & DATE

MARKS AWARDED: /10

LAB: Familiarization to Proteus and Lab Equpiment

TASK # 1:

INTRODUCTION:

Performing task 1 of lab manual 1, in which we have to design the following circuit on proteus:

PROCEDURE:

1. To begin, I developed a circuit simulation.

2. This circuit incorporates four diodes, an AC voltage source, and an oscilloscope for waveform
analysis.
3. Once the circuit was constructed, I adjusted the AC source's amplitude to 12V and its frequency to
50Hz.
4. Employing this setup resulted in the generation of the following waveform.

CIRCUIT DIAGRAM:

EDC LAB NUCES, ISLAMABAD Page 2 of 7

Electronic Devices National University Roll No: __________ L
& Circuits
(EL-1004)
of Computer and Emerging Sciences
Islamabad
a
b
#
01
_________________________________________________________________________________

EDC LAB NUCES, ISLAMABAD Page 3 of 7

Electronic Devices National University Roll No: __________ L
& Circuits
(EL-1004)
of Computer and Emerging Sciences
Islamabad
a
b
#
01
_________________________________________________________________________________

TASK # 2:

INTRODUCTION:

We are constructing a circuit as shown below, on proteus and simulate.We will vary the input voltage
Vin according the values given in the table and by using ampere meter and volt meter record the
values of Id and Vd.

EDC LAB NUCES, ISLAMABAD Page 4 of 7

Electronic Devices National University Roll No: __________ L
& Circuits
(EL-1004)
of Computer and Emerging Sciences
Islamabad
a
b
#
01
_________________________________________________________________________________

PROCEDURE:

The primary objective within this circuit was the determination of voltage and current values.

2. Initially, I formulated a circuit simulation.

3. The circuit configuration encompassed a DC voltage source, a diode, a DC voltmeter, a DC

ammeter, and a 1k-ohm resistor.

4. To achieve this, the voltmeter was connected in parallel to exploit uniform voltage across parallel
elements, while the ammeter was situated in series to capitalize on consistent current flow within the
series arrangement.

CIRCUIT DIAGRAM:

EDC LAB NUCES, ISLAMABAD Page 5 of 7

Electronic Devices National University Roll No: __________ L
& Circuits
(EL-1004)
of Computer and Emerging Sciences
Islamabad
a
b
#
01
_________________________________________________________________________________

Vin Simulated Results

(V)
Vd (V) Id (mA) Slope (Id/Vd)
0.0 0 0 0
0.2 0.2 0 0
0.4 0.4 0 0
0.6 0.57 0.03 0.052
0.8 0.611 0.19 0.31
1.0 0.63 0.37 0.587
1.2 0.64 0.56 0.875
1.4 0.65 0.75 1.15
1.50
1.6 0.63 0.95

1.8 0.66 1.14 1.72

2.0 0.66 1.34 2.03
3.0 0.68 2.32 3.41
4.79
4.0 0.69 3.31

5.0 0.69 4.31 6.24

0.70
6.0 5.30 7.5

7.0 0.70 6.30 9

8.0 0.71 7.29 10.26
9.0 0.71 8.29 11.6

EDC LAB NUCES, ISLAMABAD Page 6 of 7

Electronic Devices National University Roll No: __________ L
& Circuits
(EL-1004)
of Computer and Emerging Sciences
Islamabad
a
b
#
01
_________________________________________________________________________________

10.0 0.72 9 12.5

EDC LAB NUCES, ISLAMABAD Page 7 of 7