SL.

# PS # TITLE

1. PS-291-1963 Safety requirements for electric mains operated electronic radio

IEC-65 -1961 receiving apparatus. (Withdrawn & superseded by PS-1007/1974)
2. PS-301-1963 Electronics.
IEC-50 (07)-1956 (Withdrawn & superseded by PS-2111(521)1990 and PS-2111(531)
1990)
3. PS-302-1963 Electroacoustics.
IEC-50(08)-1960 (Withdrawn & superseded by PS-2111(801)1990 and
PS-2111(806)/1990)
4. PS-310-1963 Signalling and security apparatus for railways.
IEC-50(31)/1959 (Withdrawn)
5. PS-315-1963 Waveguides.
IEC-50(62)/1961 (Withdrawn & superseded by PS-2111(726)/1990)
6. PS-316-1963 Electrobiology.
IEC-50(70)/1959 (Withdrawn & superseded by PS-2111(881)/1990)
7. PS-481-1965 Low-cost low-sensitivity single-band medium wave radio receivers
for a.c. mains or battery operation.
8. PS-482-1965 Medium sensitivity single-band medium-wave radio receivers for
a.c. mains or battery operation.
9. PS-483-1965 Medium and short wave radio receivers for a.c. mains or battery
operation.
10. PS-1003-1974 Letter symbols to be used in electrical technology.
IEC-27-2/1972 Telecommunications and electronics.
(Withdrawn)
11. PS-1005-1994 Marking codes for resistors and capacitors. (1st Revision)
IEC-62/1992 (Withdrawn & superseded by PS:IEC 60062-2015 (2nd Revision)
12. PS-1006-1974 Preferred number series for resistors and capacitors.
IEC-63/1963 (Withdrawn)
13. PS-1007-1974 Safety requirements for mains operated electronic and related
IEC-65/1972 equipment for domestic and similar general use.
(Replaced PS-291/1963)
(Withdrawn & superseded by PS: IEC 60065-2001)
14. PS-1008-1974 Dimensions of electronic tubes and valves.
IEC-67/1966 (Withdrawn)
15. PS-1036-1974 Characteristic impedances and dimensions of radio frequency
IEC-78/1967 coaxial cables. (Withdrawn & superseded by PS-2998/1991)
16. PS-1037/1974 Fixed capacitors for direct current using impregnated paper or paper
IEC-80/1964 / plastic film dielectric.
(Withdrawn)
17. PS-1038/1974 Recommended methods of measurement on receivers for frequency-
IEC-91/1958 modulation broadcast transmissions.
(Withdrawn & superseded by PS-1275-4/1998)
18. PS-1040/1974 Magnetic tape sound recording and reproducing systems.
IEC-94/1968 Dimensions and characteristics.
 2

(Withdrawn & superseded by PS-3360-1/1994)

19. PS-1041/1974 Radio-frequency cables. Guide to the design of detailed
IEC-96-0/1970 specifications.
(Withdrawn)
20. PS-1042/1974 Radio-frequency cables. General requirements and measuring
IEC-96-1/1971 methods. (Withdrawn)
21. PS-1043/1974 Radio-frequency cables. Relevant cable specifications.
IEC-96-2/1961 (Withdrawn & superseded by PS-3542-2/1998)
22. PS-1044/1974 Processed disk records and reproducing equipment.
IEC-98/1964 (Withdrawn & superseded by PS-4502/1999)
23. PS-1047/1974 Methods for the measurement of direct interelectrode capacitances
IEC-100/1962 of electronic tubes and valves. (Withdrawn)
24. PS-1048/1974 Aluminum electrolytic capacitors for long life (type 1) and for general
purpose application (type 2).
25. PS-1049/1974 Recommended methods of measurement of radiated and conducted
IEC-106/1974 interference from receivers for amplitude-modulation, frequency-
modulation and television broadcast transmissions.
(Withdrawn & superseded by PS-2898/1990)
26. PS-1050/1974 Recommended methods of measurement of receivers for television
IEC-107/1960 broadcast transmissions.
(Withdrawn & superseded by PS-4123-1/1998, PS-4123-2/1998, PS-
4123-3/1998, PS-4123-4/1998, PS-4123-5/1998 and PS-4123-
6/1998)
27. PS-1051/1974 Ceramic dielectric capacitors. Type 1.
IEC-108/1967 (Withdrawn & superseded by PS-4496-8/1999)
28. PS-1053-1/1989 Fixed resistors for use in electronic equipment-
Part 1: Generic specification. (1st Revision)
(Based on IEC-115-1/1982)
29. PS-1053-2/1990 Fixed resistors for use in electronic equipment-
Part 2: Sectional specification. Fixed low-power, non-wirewound
resistors.
(Replaced PS-1054/1974)
(Based on IEC-115-2/1982)
30. PS-1053-2-1/1990 Fixed resistors for use in electronic equipment-
Part 2: Blank detail specification: Fixed low-power non-wirewound
resistors. Assessment level E.
(Replaced PS-1054/1974)
(Based on IEC-115-2-1/1982)
31. PS-1053-4/1990 Fixed resistors for use in electronic equipment-
Part 4: Sectional specification: Fixed power resistors.
(Based on IEC-115-4/1982)
32. PS-1053-4-1/1990 Fixed resistors for use in electronic equipment-
Part 4: Blank detail specification: Fixed power resistors. Assessment
level E.
(Based on IEC-115-4-1/1983)
33. PS-1053-4-2/2001 Fixed resistors for use in electronic equipment-
 3

Part 4: Blank detail specification: Fixed power resistors. Assessment

level F.
(Based on IEC-115-4-2/1992)
34. PS-1053-4-3/2001 Fixed resistors for use in electronic equipment-
Part 4: Blank detail specification: Fixed power resistors, heat-sink
types. Assessment level H.
(Based on IEC-115-4-3/1993)
35. PS-1053-5/1991 Fixed resistors for use in electronic equipment-
Part 5: Sectional specification: Fixed precision resistors.
(Based on IEC-115-5/1982)
36. PS-1053-5-1/1991 Fixed resistors for use in electronic equipment-
Part 5: Blank detail specification: Fixed precision resistors.
Assessment level E.
(Based on IEC-115-5-1/1983)
37. PS-1053-6/1991 Fixed resistors for use in electronic equipment-
Part 6: Sectional specification: Fixed resistor networks with
individually measurable resistors.
(Based on IEC-115-6/1983)
38. PS-1053-6-1/1991 Fixed resistors for use in electronic equipment-
Part 6: Blank detail specification: Fixed resistor networks with
individually measurable resistors, all of equal value and equal
dissipation. Assessment level E.
(Based on IEC-115-6-1/1983)
39. PS-1053-6-2/1992 Fixed resistors for use in electronic equipment-
Part 6: Blank detail specification: Fixed resistor networks with
individually measurable resistors, of either different resistance
values or different rated dissipations. Assessment level E.
(Based on IEC-115-6-2/1983)
40. PS-1053-7/1993 Fixed resistors for use in electronic equipment-
Part 7: Sectional specification: Fixed resistor networks in which not
all resistors are individually measurable.
(Based on IEC-115-7/1984)
41. PS-1053-7-1/1993 Fixed resistors for use in electronic equipment-
Part 7: Blank detail specification: Fixed resistor networks in which
not all resistors are individually measurable. Assessment level E.
(Based on IEC-115-7-1/1984)
42. PS-1053-8/1995 Fixed resistors for use in electronic equipment. Part 8:
Sectional specification: Fixed chip resistors.
(Based on IEC-115-8/1989)
43. PS-1053-8-1/1995 Fixed resistors for use in electronic equipment. Part 8: Blank detail
specification: Fixed chip resistors. Assessment level E.
(Based on IEC-115-8-1/1989)
44. PS-1053-9/2012 Fixed resistors for use in electronic equipment –
Part 9: Sectional specification: Fixed surface mount resistor
networks with individually measurable resistors.
(Based on IEC-60115-9/2003)
 4

45. PS-1053-9-1/2012 Fixed resistors for use in electronic equipment –

Part 9-1: Blank detail specification: Fixed surface mount resistor networks
with individually measurable resistors - Assessment level EZ.
(Based on IEC-60115-9-1/2003)
46. PS-1054/1974 Fixed low power non-wirewound resistors.-
IEC-115-2/1972 Selection of methods of test and general requirements.
(Withdrawn & superseded by PS-1053-2/ 1990 and PS-1053-2-1/
1990)
47. PS-1055/1974 Wirewound resistors. Type – 1.
IEC-115-3/1971 Selection of methods of test and general requirements.
(Withdrawn)
48. PS-1056/1974 Wirewound resistors. Type – 1. Detail specification.
IEC-115-3-1/1971 (Withdrawn)
49. PS-1057/1974 Recommendations for receiver-type metallized mica capacitors for
IEC-116/1959 use in electronic equipment.
(Withdrawn & superseded by PS-4496-5/1999)
50. PS-1064/1974 Recommended graphical symbols.
IEC-117-6/1964 Variability, examples of resistors, elements of electronic tubes,
valves and rectifiers.
(Withdrawn)
51. PS-1065/1974 Recommended graphical symbols.
IEC-117-7/1971 Semiconductor devices. Capacitors.
(Withdrawn)
52. PS-1066/1974 Recommended graphical symbols.
IEC-117-8/1971 Symbols for architectural diagrams.
(Withdrawn)
53. PS-1067/1974 Recommended graphical symbols.
IEC-117-9/1968 Telephony, telegraphy and transducers.
(Withdrawn & superseded by PS-2342)
54. PS-1068/1974 Recommended graphical symbols.
IEC-117-10/1968 Aerials (Antennas) and radio stations.
(Withdrawn & superseded by PS-2342)
55. PS-1069/1974 Recommended graphical symbols.
IEC-117-11/1968 Microwave technology.
(Withdrawn & superseded by PS-2342)

56. PS-1070/1974 Recommended graphical symbols.

IEC-117-12/1968 Frequency spectrum diagrams.
(Withdrawn & superseded by PS-2342)
57. PS-1071/1974 Recommended graphical symbols.
IEC-117-13/1968 Block symbols for transmission and miscellaneous applications.
(Withdrawn & superseded by PS-2342)
58. PS-1072/1974 Recommended graphical symbols.
IEC-117-14/1968 Telecommunication lines and accessories.
(Withdrawn)
59. PS-1073/1974 Recommended graphical symbols.
 5

IEC-117-15/1972 Binary logic elements.

(Withdrawn & superseded by PS-2342)
60. PS-1074/1974 Recommended graphical symbols.
IEC-117-16/1972 Symbols for ferrite cores and magnetic storage matrices.
(Withdrawn & superseded by PS-2342)
61. PS-1075/1974 Recommended methods for measurements of the electro-acoustical
IEC-118/1959 characteristics of hearing aids.
(Withdrawn)
62. PS-1076/1974 Recommendations for polycrystalline semiconductor rectifier stacks
IEC-119/1960 and equipment.
(Withdrawn & superseded by PS-4127/1998)
63. PS-1077/1974 Quartz crystal units for frequency control and selection.
IEC-122-1/1962 Section One: Standard values and conditions.
Section Two: Test conditions.
(Withdrawn & superseded by PS-3148-1/1992)
64. PS-1078/1974 Quartz crystal units for frequency control and selection.
IEC-122-3/1962 Section Three: Guide to the use of quartz oscillators, crystals.
(Withdrawn & superseded by PS-3148-2/1998)
65. PS-1079/1974 Quartz crystal units for frequency control and selection.
IEC-122-4/1962 Section Four: Standard outlines.
(Withdrawn & superseded by PS-3148-3/1998)
66. PS-1080/1974 Recommendations for sound level meters.
IEC-123/1961 (Withdrawn)
67. PS-1081/1974 General classification of ferromagnetic oxide materials and
IEC-125/1961 definitions of terms.
(Withdrawn & superseded by PS-2111(901)/ 1990)
68. PS-1082/1974 PS reference coupler for the measurement of hearing aids
IEC-126/1973 using earphones coupled to the ear by means of ear inserts.
(Withdrawn)
69. PS-1083/1974 Connectors for frequencies below 3 MHz.
IEC-130-0/1970 Guide to drawing information in detail specifications.
(Withdrawn)
70. PS-1084/1974 Connectors for frequencies below 3 MHz.
IEC-130-1/1962 General requirements and measuring methods. (Withdrawn)

71. PS-1085/1974 Connectors for frequencies below 3 MHz.

IEC-130-2/1965 Connectors for radio receivers and associated sound equipment.
(Withdrawn)
72. PS-1086/1974 Connectors for frequencies below 3 MHz.
IEC-130-3/1965 Battery connectors.
(Withdrawn)
73. PS-1087/1974 Connectors for frequencies below 3 MHz.
IEC-130-4/1966 Circular multipole connectors with threaded coupling.
(Withdrawn)
74. PS-1088/1974 Connectors for frequencies below 3 MHz.
 6

IEC-130-5/1966 Rectangular multipole connectors with blade contacts.

(Withdrawn)
75. PS-1089/1974 Connectors for frequencies below 3 MHz.
IEC-130-6/1965 Rectangular miniature multipole connectors with blade contacts.
(Withdrawn)
76. PS-1090/1974 Connectors for frequencies below 3 MHz.
IEC-130-7/1971 Circular multipole connectors with bayonet or push-pull coupling.
(Withdrawn)
77. PS-1091/1974 Connectors for frequencies below 3 MHz.
IEC-130-8/1969 Concentric connectors for audio circuits in radio receivers.
(Withdrawn)
78. PS-1092/1974 Connectors for frequencies below 3 MHz.
IEC-130-9/1971 Circular connectors for radio and associated sound equipment.
(Withdrawn)
79. PS-1093/1974 Connectors for frequencies below 3 MHz.
IEC-130-10/1971 Connectors for coupling an external low-voltage power supply to
portable entertainment equipment.
(Withdrawn)
80. PS-1094/1974 Connectors for frequencies below 3 MHz.
IEC-130-11/1971 Edge socket connectors with closed ends and having a contact
spacing of 2.54 mm (0.1 in) mating either with board mounted
connectors or printed wiring boards with edge board contacts.
(Withdrawn)
81. PS-1095/1974 Connectors for frequencies below 3 MHz.
IEC-130-12/1973 Link and test connectors.
(Withdrawn)
82. PS-1096/1974 Connectors for frequencies below 3 MHz.
IEC-130-13/1971 Edge socket connectors with open ends, off-centre guide, having a
contact spacing of 2.54 mm (0.1 in).
(Withdrawn)
83. PS-1100/1974 Rotary wafer switches (low current rating)-
IEC-132-1/1962 General requirements and measuring methods.
(Withdrawn)
84. PS-1101/1974 Rotary wafer switches (low current rating)-
IEC-132-2/1963 Rotary wafer switches with central mounting.
(Withdrawn)
85. PS-1102/1974 Rotary wafer switches (low current rating)-
IEC-132-3/1963 Rotary wafer switches with two-hole mounting.
(Withdrawn)
86. PS-1103/1974 Rotary wafer switches (low current rating)-
IEC-132-4/1966 Rotary wafer switches with central mounting; maximum 12
positions; maximum diameter 40 mm.
(Withdrawn)
87. PS-1104/1974 Rotary wafer switches (low current rating)-
IEC-132-5/1966 Rotary wafer switches with two-hole mounting; maximum 26
positions; maximum diameter 60 mm.
 7

(Withdrawn)
88. PS-1105/1974 Dimensions of pot-cores made of ferromagnetic oxides and
IEC-133/1967 associated parts.
(Withdrawn)
89. PS-1106/1974 Rating systems for electronic tubes and valves and analogous
IEC-134/1961 semiconductor devices.
(Withdrawn)
90. PS-1107/1974 Numbering of electrodes and designation of units in electronic tubes
IEC-135/1961 and valves.
(Withdrawn)
91. PS-1108/1974 Methods of measurement of essential electrical properties of
IEC-138/1962 receiving aerials in the frequency range from 30 MHz to 1000 MHz.
(Withdrawn & superseded by PS-2996-2/1992,PS-2996-3/1992 and
PS-2996-4/1992 )
92. PS-1109/1974 Preparation of outline drawings of oscilloscope and picture tubes.
IEC-139/1962 (Withdrawn)
93. PS-1111/1974 Semiconductor convertors.
IEC-146/1973 (Withdrawn & superseded by PS-2899-4/1990)
94. PS-1112/1974 Essential ratings and characteristics of semiconductor devices
IEC-147-0/1966 and general principles of measuring methods.
General and terminology.
(Withdrawn & superseded by PS-2345/1990)
95. PS-1113/1974 Essential ratings and characteristics of semiconductor devices
IEC-147-1/1972 and general principles of measuring methods.
Essential ratings and characteristics.
(Withdrawn & superseded by PS-2345/1990)
96. PS-1114/1974 Essential ratings and characteristics of semiconductor devices
IEC-147-2/1963 and general principles of measuring methods.
General principles of measuring methods.
(Withdrawn & superseded by PS-2345/1990)
97. PS-1115/1974 Essential ratings and characteristics of semiconductor devices
IEC-147-3/1970 and general principles of measuring methods.
Reference methods of measurement.
(Withdrawn & superseded by PS-2345/1990)

98. PS-1116/1974 Letter symbols for semiconductor devices and integrated

IEC-148/1969 microcircuits.
(Withdrawn)
99. PS-1117/1974 Sockets and accessories for electronic plug-in devices.
IEC-149-1/1963 General requirements and methods of test.
(Withdrawn)
100. PS-1118/1974 Sockets and accessories for electronic plug-in devices.
IEC-149-2/1965 Specification sheets for sockets and dimensions of wiring jigs and
pin straighteners.
(Withdrawn)
 8

101. PS-1119/1974 Measurements of the electrical properties of electronic tubes.

IEC-151-0/1966 Precautions relating to methods of measurement of electronic tubes
and valves.
(Withdrawn)
102. PS-1120/1974 Measurements of the electrical properties of electronic tubes.
IEC-151-1/1963 Measurement of electrode current.
(Withdrawn)
103. PS-1121/1974 Measurements of the electrical properties of electronic tubes.
IEC-151-2/1963 Measurement of heater or filament current.
(Withdrawn)
104. PS-1122/1974 Measurements of the electrical properties of electronic tubes.
IEC-151-3/1963 Measurement of equivalent input and output admittances.
(Withdrawn)
105. PS-1123/1974 Measurements of the electrical properties of electronic tubes.
IEC-151-4/1963 Methods of measuring noise factor.
(Withdrawn)
106. PS-1124/1974 Measurements of the electrical properties of electronic tubes.
IEC-151-5/1964 Methods of measuring hiss and hum. (Withdrawn)
107. PS-1125/1974 Measurements of the electrical properties of electronic tubes.
IEC-151-6/1965 Methods of application of mechanical shock (impulse) excitation to
electronic tubes and valves.
(Withdrawn)
108. PS-1126/1974 Measurements of the electrical properties of electronic tubes.
IEC-151-7/1964 Measurement of equivalent noise resistance.
(Withdrawn)
109. PS-1127/1974 Measurements of the electrical properties of electronic tubes.
IEC-151-8/1966 Measurement of cathode heating time and heater warm-up time.
(Withdrawn)
110. PS-1128/1974 Measurements of the electrical properties of electronic tubes.
IEC-151-9/1966 Methods of measuring the cathode-interface impedance.
(Withdrawn)
111. PS-1129/1974 Measurements of the electrical properties of electronic tubes.
IEC-151-10/1966 Methods of measurement of audio-frequency output power and
distortion.
(Withdrawn)

112. PS-1130/1974 Measurements of the electrical properties of electronic tubes.

IEC-151-11/1966 Methods of measurement of radio-frequency output power.
(Withdrawn)
113. PS-1131/1974 Measurements of the electrical properties of electronic tubes.
IEC-151-12/1966 Methods of measuring electrode resistance, transconductance,
amplification factor, conversion resistance and conversion
transconductance.
(Withdrawn)
114. PS-1132/1974 Measurements of the electrical properties of electronic tubes.
IEC-151-13/1966 Methods of measurement of emission current from hot cathodes for
 9

high vacuum electronic tubes and valves.

(Withdrawn)
115. PS-1133/1974 Measurements of the electrical properties of electronic tubes.
IEC-151-14/1975 Methods of measurement of radar and oscilloscope cathode-ray
tubes.
(Withdrawn)
116. PS-1134/1974 Measurements of the electrical properties of electronic tubes.
IEC-151-15/1967 Methods of measurement of spurious and unwanted electrode
currents.
(Withdrawn)
117. PS-1135/1974 Measurements of the electrical properties of electronic tubes.
IEC-151-16/1968 Methods of measurement for television picture tubes.
(Withdrawn)
118. PS-1136/1974 Measurements of the electrical properties of electronic tubes.
IEC-151-17/1969 Methods of measurement of gas filled tubes and valves.
(Withdrawn)
119. PS-1137/1974 Measurements of the electrical properties of electronic tubes.
IEC-151-18/1968 Methods of measurement of noises due to mechanical or acoustic
excitations.
(Withdrawn)
120. PS-1138/1974 Measurements of the electrical properties of electronic tubes.
IEC-151-19/1969 Methods of measurement on corona stabilizers.
(Withdrawn)
121. PS-1139/1974 Measurements of the electrical properties of electronic tubes.
IEC-151-20/1969 Methods of measurement of thyratron pulse modulators.
(Withdrawn)
122. PS-1140/1974 Measurements of the electrical properties of electronic tubes.
IEC-151-21/1969 Methods of measurement of cross-modulation in electronic tubes and
valves.
(Withdrawn)
123. PS-1141/1974 Measurements of the electrical properties of electronic tubes.
IEC-151-22/1970 Methods of measurement for cold cathode counting and indicator
tubes.
(Withdrawn)

124. PS-1142/1974 Measurements of the electrical properties of electronic tubes.

IEC-151-23/1970 Methods of measurement of vacuum pulse modulator tubes and
valves.
(Withdrawn)
125. PS-1143/1974 Measurements of the electrical properties of electronic tubes.
IEC-151-24/1971 Methods of measurement of cathode-ray charge-storage tubes.
(Withdrawn)
126. PS-1144/1974 Measurements of the electrical properties of electronic tubes.
IEC-151-25/1971 Methods of measurement of Geiger-Muller counter tubes.
(Withdrawn)
 10

127. PS-1145/1974 Measurements of the electrical properties of electronic tubes.

IEC-151-26/1971 Methods of measurement for camera tubes.
(Withdrawn)
128. PS-1146/1974 Hollow metallic waveguides.
IEC-153-1/1964 General requirements and measuring methods.
(Withdrawn & superseded by PS-3681-1/1995)
129. PS-1147/1974 Hollow metallic waveguides.
IEC-153-2/1974) Relevant specifications for ordinary rectangular waveguides.
(Withdrawn & superseded by PS-3681-2/1995)
130. PS-1148/1974 Hollow metallic waveguides.
IEC-153-3/1964 Relevant specifications for flat rectangular waveguides.
(Withdrawn & superseded by PS-3681-3/1996)
131. PS-1149/1974 Hollow metallic waveguides.
IEC-153-4/1973 Relevant specifications for circular waveguides.
(Withdrawn & superseded by PS-3681-4/1998)
132. PS-1150/1974 Hollow metallic waveguides.
IEC-153-5/1968) Relevant specifications for rectangular waveguides with circular
outside cross section.
(Withdrawn)
133. PS-1151/1974 Hollow metallic waveguides.
IEC-153-6/1967 Relevant specifications for medium flat rectangular waveguides.
(Withdrawn & superseded by PS-3681-6/1998)
134. PS-1152/1974 Flanges for waveguides.
IEC-154-1/1964 General requirements and measuring methods.
(Withdrawn & superseded by PS-4163-1/1998)
135. PS-1153/1974 Flanges for waveguides.
IEC-154-2/1968 Relevant specifications for flanges for ordinary rectangular
waveguides.
(Withdrawn & superseded by PS-4163-2/1998)
136. PS-1154/1974 Flanges for waveguides.
IEC-154-3/1968 Relevant specifications for flanges for flat rectangular waveguides.
(Withdrawn & superseded by PS-4163-3/1998)
137. PS-1155/1974 Flanges for waveguides.
IEC-154-4/1969 Relevant specifications for flanges for circular waveguides.
(Withdrawn & superseded by PS-4163-4/1998)

138. PS-1156/1974 Dimensions of the mating parts of radio-frequency connectors.

IEC-159/1964 (Withdrawn)
139. PS-1157/1974 Capacitors for radio interference suppression.
IEC-161/1965 (Withdrawn)
140. PS-1158/1974 Sensitive switches.
IEC-163-1/1968 General requirements and measuring methods.
(Withdrawn)
141. PS-1160/1974 Fixed metallized paper dielectric capacitors for direct current.
IEC-166/1965 (Withdrawn)
 11

142. PS-1161/1974 Radio-frequency connectors.

IEC-169-1/1965 General requirements and measuring methods.
(Withdrawn & superseded by PS-4182-1/1998)
143. PS-1162/1974 Radio-frequency connectors.
IEC-169-2/1965 Coaxial un-matched connectors.
(Withdrawn & superseded by PS-4182-2/1998)
144. PS-1163/1974 Radio-frequency connectors.
IEC-169-3/1965 Two-pin connectors for twin balanced aerial feeders.
(Withdrawn & superseded by PS-4182-3/1998)
145. PS-1164/1974 Radio-frequency connectors.
IEC-169-4/1967 RF coaxial connectors for cables 1043, PS: 50-12.
(Withdrawn & superseded by PS-4182-4/1998)
146. PS-1165/1974 Radio-frequency connectors.
IEC-169-5/1970 RF coaxial connectors for cables 1043, PS: 50-17 and larger.
(Withdrawn & superseded by PS-4182-5/1998)
147. PS-1166/1974 Radio-frequency connectors.
IEC-169-6/1971 RF coaxial connectors for cables 1043, PS: 75-17 and larger.
(Withdrawn & superseded by PS-4182-6/1998)
148. PS-1167/1974 Fundamental parameters of connectors for printed wiring boards.
IEC-171/1964 (Withdrawn)
149. PS-1170/1974 Pure tone audiometers for general for general diagnostic purposes.
IEC-177/1965 (Withdrawn)
150. PS-1171/1974 Precision sound level meters. (Withdrawn)
IEC-179/1973
151. PS-1178/1974 Ceramic dielectric capacitors Type 2. (Withdrawn)
IEC-187/1965
152. PS-1179/1974 Low-frequency cables and wires with PVC insulation and
IEC-189-1/1965 PVC sheath.
General tests and measuring methods.
(Withdrawn & superseded by PS-3362-1/2002)
153. PS-1180/1974 Low-frequency cables and wires with PVC insulation and
IEC-189-2/1972 PVC sheath.
Cables in pairs, triples, quads and quintuples for inside installations.
(Withdrawn & superseded by PS-3362-2/1994)

154. PS-1181/1974 Low-frequency cables and wires with PVC insulation and
IEC-189-3/1967 PVC sheath.
Equipment wires with solid or stranded conductors, PVC insulated in
singles, pairs and triples.
(Withdrawn & superseded by PS-3362-3/1994)
155. PS-1182/1974 Low-frequency cables and wires with PVC insulation and
IEC-189-4/1968 PVC sheath.
Distribution wires with solid conductors, PVC insulated in pairs and
triples, quads and quintuples.
(Withdrawn & superseded by PS-3362-4/1996)
 12

156. PS-1183/1974 Low-frequency cables and wires with PVC insulation and
IEC-189-5/1969 PVC sheath.
Equipment wires with solid or stranded conductors, PVC insulated
screened, single or one pair.
(Withdrawn & superseded by PS-3362-5/1996)
157. PS-1184/1974 Low-frequency cables and wires with PVC insulation and
IEC-189-6/1969 PVC sheath.
Signalling cables in singles for telecommunication equipment and
installation.
(Withdrawn)
158. PS-1185/1974 Low-frequency cables and wires with PVC insulation and
IEC-189-7/1971 PVC sheath.
Distribution wires with solid conductors, PVC insulated polyamide
coated, in singles, pairs, triples, quads and quintuples.
(Withdrawn)
159. PS-1186/1974 Non-wirewound potentiometers Type 2.
IEC-190/1966 (Withdrawn)
160. PS-1187/1974 Mechanical standardization of semiconductor devices.
IEC-191-1/1966 Part 1: Preparation of drawings of semiconductor devices.
(Withdrawn & superseded by PS-4160-1/1998)
161. PS-1188/1974 Mechanical standardization of semiconductor devices.
IEC-191-2/1966 Part 2: Dimensions.
(Withdrawn & superseded by PS-4160-2/1998)
162. PS-1189/1974 Terms and definitions of printed circuits.
IEC-194/1965 (Withdrawn & superseded by PS-2347/1989)
163. PS-1190/1974 Method of measurement of current noise generated in fixed resistors.
IEC-195/1965 (Withdrawn)
164. PS-1192/1974 High-voltage connecting wire with flame retarding insulation for
IEC-197/1965 use in television receivers.
(Withdrawn & superseded by PS-4161/1998)
165. PS-1193/1974 Polyester film dielectric capacitors for direct current. (Withdrawn)
IEC-202/1965
166. PS-1194/1974 Dimensions of the crimp area of machined crimp type contacts.
IEC-203/1966 (Withdrawn)
167. PS-1195/1974 Calculations of the effective parameters of magnetic piece parts.
IEC-205/1966 (Withdrawn)
168. PS-1196/1974 Designation of the quantities characterizing the magnetic and electric
IEC-206/1966 properties of vacuum and a substance.
(Withdrawn)
169. PS-1197/1974 Safety requirements for radio transmitting equipment.
IEC-215-1/1966 Requirements.
(Withdrawn & superseded by PS-2912/1990)
170. PS-1198/1974 Safety requirements for radio transmitting equipment. Test methods.
IEC-215-2/1967 (Withdrawn & superseded by PS-2912/1990)
171. PS-1200/1974 Electronic voltmeters.
IEC-217/1967 (Withdrawn)
 13

172. PS-1201/1974 Guide for the drafting of performance specifications for cores of
IEC-218/1966 tuned transformers and inductors of ferromagnetic oxides for
telecommunication.
(Withdrawn)
173. PS-1202/1974 Guide for the drafting of performance specifications for cores of
IEC-219/1966 broad-band transformers and inductors of ferromagnetic oxides for
telecommunication.
(Withdrawn)
174. PS-1203/1974 Dimensions of tubes, pins and rods of ferromagnetic oxides.
IEC-220/1966 (Withdrawn)
175. PS-1204/1974 Dimensions of screw cores made of ferromagnetic oxides.
IEC-221/1966 (Withdrawn)
176. PS-1205/1974 Methods for specifying the characteristics of auxiliary equipment
IEC-222/1966 for shock and vibration measurement.
(Withdrawn)
177. PS-1206/1974 Dimensions of aerial rods and slabs of ferromagnetic oxides.
IEC-223/1966 (Withdrawn)
178. PS-1207/1974 Marking of control setting on hearing aids.
IEC-224/1966 (Withdrawn)
179. PS-1208/1974 Octave, half-octave and third-octave band filters intended for
IEC-225/1966 analysis of sounds and vibrations.
(Withdrawn)
180. PS-1209/1974 Dimensions of cross cores (X – cores) made of ferromagnetic
IEC-226/1967 oxides and associated parts.
(Withdrawn)
181. PS-1213/1974 General principles of nuclear reactor instrumentation.
IEC-231/1967 . (Withdrawn)
182. PS-1214/1974 Dimensions of ceramic dielectric capacitors of the plate type.
IEC-234/1967 (Withdrawn)
183. PS-1215/1974 Measurement of the electrical properties of microwave tubes.
IEC-235-1/1972 Terminology.
(Withdrawn)
184. PS-1216/1974 Measurement of the electrical properties of microwave tubes.
IEC-235-2/1972 General measurements.
(Withdrawn)

185. PS-1217/1974 Measurement of the electrical properties of microwave tubes.

IEC-235-3/1972 Disk seal tubes.
186. PS-1218/1974 Measurement of the electrical properties of microwave tubes.
IEC-235-4/1972 Magnetrons.
(Withdrawn)
187. PS-1219/1974 Measurement of the electrical properties of microwave tubes.
IEC-235-5/1972 Low-power oscillator klystrons.
(Withdrawn)
188. PS-1220/1974 Measurement of the electrical properties of microwave tubes.
IEC-235-6/1972 High-power klystrons.
 14

(Withdrawn)
189. PS-1221/1974 Measurement of the electrical properties of microwave tubes.
IEC-235-7/1972 Gas-filled microwave switching devices.
(Withdrawn)
190. PS-1222/1974 Measurement of the electrical properties of microwave tubes.
IEC-235-8/1972 Backward-wave oscillator tubes- “O” type.
(Withdrawn)
191. PS-1223/1974 Methods for the designation of electrostatic deflecting electrodes of
IEC-236/1974 cathode-ray tubes.
(Withdrawn)
192. PS-1224/1974 Ignitrons to be used in welding machine control.
IEC-237/1967 (Withdrawn)
193. PS-1225/1974 Methods of measurement for radio transmitters.
IEC-244-1/1968 General conditions of measurement, frequency, output power and
power consumption.
(Withdrawn & superseded by PS-4113-1/1998)
194. PS-1226/1974 Methods of measurement for radio transmitters.
IEC-244-2/1969 Band width, out-of-band power and power of non-essential
oscillations.
(Withdrawn & superseded by PS-4113-2/1998)
195. PS-1227/1974 Methods of measurement for radio transmitters.
IEC-244-3/1972 Wanted and unwanted modulation.
(Withdrawn & superseded by PS-4113-3/1998)
196. PS-1228/1974 Methods of measurement for radio transmitters.
IEC-244-4/1973 Amplitude/frequency characteristics and non-linearity distortion in
transmitters for radio-telephony and sound broadcasting.
(Withdrawn & superseded by PS-4113-4/1998)
197. PS-1229/1974 Methods of measurement for radio transmitters.
IEC-244-5/1971 Measurements particular to transmitters and transposers for
monochrome and colour television.
(Withdrawn & superseded by PS-4113-5/1998)
198. PS-1230/1974 Base materials for printed circuits.
IEC-249-1/1968 Test methods.
(Withdrawn & superseded by PS-2348-1/1989)

199. PS-1231/1974 Base materials for printed circuits.

IEC-249-2/1970 Specifications.
(Withdrawn & superseded by PS-2348-2-1/1989 to PS-2348-2-
19/1989)
200. PS-1232/1974 Base materials for printed circuits.
IEC-249-3/1973 Special materials used in connection with printed boards.
(Withdrawn & superseded by PS-2348-3-1/1989 and PS-2348-3-
3/1999)
 15

201. PS-1233/1974 Recommended methods for the determination of the dissipation factor
of electrical insulating materials at power, audio and radio frequencies
including meter wave lengths.

202. PS-1238/1974 Sealing test for pressurized waveguide tubing and assemblies.
IEC-261/1968 (Withdrawn & superseded by PS-4166/1998)
203. PS-1239/1974 Scales and sizes for plotting frequency characteristics and polar
IEC-263/1968 diagrams.
(Withdrawn)
204. PS-1244/1974 Sound system equipment. General.
IEC-268-1/1968 (Withdrawn)
205. PS-1245/1974 Sound system equipment. Explanation of general terms.
IEC-268-2/1971 (Withdrawn)
206. PS-1246/1974 Sound system equipment. Sound system amplifiers.
IEC-268-3/1969 (Withdrawn)
207. PS- 1247/1974 Sound system equipment.
Part 4: Microphones.
(Withdrawn & superseded by PS-1247-4/2014)

PS- 1247 – 4/2014 Sound system equipment –

Part 4: Microphones. (1st Revision)
(Based on IEC-60268-4/2010)
208. PS-1248/1974 Sound system equipment. Loudspeakers.
IEC-268-5/1972 (Withdrawn)
209. PS-1249/1974 Sound system equipment. Auxilliary passive elements.
IEC-268-6/1971 (Withdrawn)
210. PS-1250/1974 Sound system equipment. Automatic gain control devices.
IEC-268-8/1973 (Withdrawn)
211. PS-1251/1974 Sound system equipment. Mechanical design features.
IEC-268-14/1971 (Withdrawn)
212. PS-1252/1974 Preliminary list of basic terms and definitions for the reliability
IEC-271/1969 of electronic equipment and the components (or parts) used therein.
(Withdrawn)
213. PS-1253/1974 Polystyrene film dielectric capacitors.
IEC-275/1968 (Withdrawn & superseded by PS-4496-7/1999)
214. PS-1254/1974 Documentation to be supplied with electronic measuring apparatus.
IEC-278/1968 (Withdrawn)
215. PS-1255/1974 Methods for the measurement of frequency and equivalent
IEC-283/1968 resistance of unwanted resonances of filter crystal units.
(Withdrawn & superseded by PS-4199/1998)
216. PS-1256/1974 Rules of behaviour with respect to possible hazards when
IEC-284/1968 dealing with electronic equipment and equipment employing similar
techniques.
 16

(Withdrawn)
217. PS-1260/1974 Tube and valve shields.
IEC-288-1/1969 General requirements and methods of test.
(Withdrawn)
218. PS-1261/1974 Tube and valve shields.
IEC-288-2/1969 Specification sheets for shields for tubes and valves and dimensions
of testing devices and gauges for shields.
(Withdrawn)
219. PS-1263/1974 Supply voltages for transistorized nuclear instruments.
IEC-293/1968 (Withdrawn)
220. PS-1264/1974 Dimensions of panels and racks (for nuclear electronic instruments)
IEC-297/1969 (Withdrawn & superseded by PS-3680-1/1995 and PS-3680-2/1995)
221. PS-1265/1974 Preferred diameters of wire terminations of capacitors and resistors.
IEC-301/1971 (Withdrawn)
222. PS-1266/1974 Standard definitions and methods of measurement for
IEC-302/1969 piezoelectric vibrators operating over the frequency range upto 30
MHz.
(Withdrawn & superseded by PS-3005/1991)
223. PS-1267/1974 PS provisional reference coupler for the calibration of
IEC-303/1970 earphones used in audiometery.
(Withdrawn)
224. PS-1268/1974 Standard colours for PVC insulation for low-frequency cables
IEC-304/1969 and wires.
(Withdrawn & superseded by PS-4175/1998)
225. PS-1269/1974 Measurement of photosensitive devices. Basic recommendations.
IEC-306/1969 (Withdrawn)
226. PS-1270/1974 Measurement of photosensitive devices.
IEC-306-2/1969 Methods of measurement of phototubes.
(Withdrawn)
227. PS-1271/1974 Measurement of photosensitive devices. Methods of measurement
IEC-306-3/1970 of photoconductive cells for use in the visible spectrum.
(Withdrawn)
228. PS-1272/1974 Measurement of photosensitive devices.
IEC-306-4/1971 Methods of measurement of photomultipliers.
(Withdrawn)
229. PS-1273/1974 Coaxial cable connectors used in nuclear instrumentation.
IEC-313/1969 (Withdrawn & superseded by PS-3999/1997)

230. PS-1274/1974 Temperature control devices for quartz crystal units.

IEC-314/1970 (Withdrawn & superseded by PS-3150/1992)
231. PS-1275-1/1990 Methods of measurement on radio receivers for various classes of
emission.
Part 1: General considerations and methods of measurement,
including audio-frequency measurements. (1st Revision)
(Replaced PS-1276/1974)
(Based on IEC-315-1/1988)
 17

232. PS-1275-3/1998 Methods of measurement on radio receivers for various classes of

IEC-315-3/1989 emission.
Part 3: Receivers for amplitude-modulated sound-broadcasting
emissions.
(Replaced PS-1277/1974)
(Withdrawn)
233. PS-1275-4/1998 Methods of measurement on radio receivers for various classes of
IEC-315-4/1997 emission.
Part 4: Receivers for frequency-modulated
sound-broadcasting emissions.
(Replaced PS-1038/1974)
(Withdrawn)
234. PS-1275-5/1991 Methods of measurement on radio receivers for various classes of
emission.
Part 5: Specialized radio-frequency measurements.
Measurement on frequency-modulated receivers of the response to
impulsive interference.
(Replaced PS-1278/1974)
(Based on IEC-315-5/1971)
235. PS-1275-6/1998 Methods of measurement on radio receivers for various classes of
IEC-315-6/1991 emission.
Part 6: General purpose communication receivers.
(Withdrawn)
236. PS-1275-7/1998 Methods of measurement on radio receivers for various classes of
IEC-315-7/1995 emission.
Part 7: Methods of measurement on digital satellite radio (DSR)
receivers.
(Withdrawn)
237. PS-1275-8/1991 Methods of measurement on radio receivers for various classes of emission.
Part 8: Radio-frequency measurements on professional receivers for
frequency-modulated telegraphy systems.
(Based on IEC-315-8/1975)
238. PS-1275-9/1998 Methods of measurement on radio receivers for various classes of emission.
IEC-315-9/1996 Part 9: Measurement of the characteristics relevant to Radio Data System
(RDS) reception.
(Withdrawn)

239. PS-1276/1974 Methods of measurement on radio receivers for various classes of

IEC-315-2/1971 emission.
Measurements particularly related to the audio-frequency part of a
receiver.
(Withdrawn & superseded by PS-1275-1/1990)
240. PS-1277/1974 Methods of measurement on radio receivers for various classes of
IEC-315-3/1973 emission.
Radio-frequency measurements on receivers for amplitude-
 18

modulated emissions.
(Withdrawn & superseded by PS-1275-3/1998)
241. PS-1278/1974 Methods of measurement on radio receivers for various classes of
IEC-315-5/1971 emission.
Specialized radio-frequency measurements.
Measurement on frequency-modulated receivers of the response to
impulsive interference.
(Withdrawn & superseded by PS-1275-5/1991)
242. PS-1290/1974 PS artificial ear, of the wideband type, for the calibration of
IEC-318/1970 earphones used in audiometery.
(Withdrawn)
243. PS-1291/1974 Presentation of reliability data on electronic components (or parts).
IEC-319/1970 (Withdrawn)
244. PS-1292/1974 Guidance for the design and use of components intended for
IEC-321/1970 mounting on boards with printed wiring and printed circuits.
(Withdrawn & superseded by PS-4474-3/1999)
245. PS-1293/1974 Analogue voltage ranges and logic levels for mains operated
IEC-323/1970 nuclear instruments.
(Withdrawn)
246. PS-1294/1974 Ceramic dielectric capacitors. Type 3.
IEC-324/1970 (Withdrawn)
247. PS-1295/1974 General requirements and measuring methods for printed wiring
IEC-326/1970 boards.
(Withdrawn & superseded by PS-2349-1/1989)
248. PS-1296/1974 Precision method for pressure calibration of one-inch standard
IEC-327/1971 condenser microphones by the reciprocity technique.
(Withdrawn)
249. PS-1297/1974 Strip-wound cut cores of grain oriented silicon-iron alloy, for
IEC-329/1971 electronic and telecommunication equipment.
(Withdrawn)
250. PS-1298/1974 Test procedures for semiconductor detectors for ionizing radiation.
IEC-333/1970 (Withdrawn & superseded by PS-3553/1994)
251. PS-1302/1974 General purpose rigid coaxial transmission lines and their
IEC-339-1/1971 associated flange connectors.
General requirements and measuring methods.
(Withdrawn & superseded by PS-4167-1/1998)

252. PS-1303/1974 General purpose rigid coaxial transmission lines and their
IEC-339-2/1972 associated flange connectors. Detail specifications.
(Withdrawn & superseded by PS-4183-2/1998)
253. PS-1304/1974 Test procedures for amplifiers and preamplifiers for semiconductor
IEC-340/1970 detectors for ionizing radiation.
(Withdrawn)
254. PS-1305/1974 Push button switches-
IEC-341-1/1970 General requirements and measuring methods.
 19

(Withdrawn)
255. PS-1306/1974 Push button switches-
IEC-341-2/1973 General rules for drafting specification sheets for push button
switches of the multi-cell type.
(Withdrawn & superseded by PS-3144-3/1992)
256. PS-1307/1974 Transverse track recorders.
IEC-347/1972 (Withdrawn & superseded by PS-4504/1999)
257. PS-1308/1974 Safety requirements for electronic measuring apparatus.
IEC-348/1971 (Withdrawn)
258. PS-1309/1974 Expression of the properties of cathode-ray oscilloscopes.
IEC-351/1971 (Withdrawn)
259. PS-1310/1974 Solderless connections.
IEC-352-1/1971 Part 1: Solderless wrapped connections.
General requirements, test methods and practical guidance.
(Withdrawn & superseded by PS-2997-1/1991)
260. PS-1313/1974 Expression of the functional performance of electronic
IEC-359/1971 measuring equipment.
(Withdrawn)
261. PS-1314/1974 Fixed tantalum capacitors with liquid or solid electrolyte.
IEC-361/1971 (Withdrawn)
262. PS-1315/1974 Guide for the collection of reliability, availability and
IEC-362/1971 maintainability of data from field performance of electronic items.
(Withdrawn)
263. PS-1316/1974 Cores for inductors and transformers for telecommunications.
IEC-367-1/1971 Measuring methods.
(Withdrawn)
264. PS-1317/1974 Piezoelectric filters.
IEC-368/1971 (Withdrawn)
265. PS-1318/1974 Guide for choosing modular dimensions for waveguide
IEC-374/1971 components.
(Withdrawn & superseded by PS-4168/1998)
266. PS-1320/1974 Fixed capacitors for use in electronic equipment. Terminology and
IEC-384-1/1972 methods of tests.
(Withdrawn)
267. PS-1321/1974 Thermal time delay switches for use in equipment for
IEC-388-1/1972 telecommunication and in electronic applications employing similar
techniques.
General requirements and measuring methods. (Withdrawn)
268. PS-1322/1974 Thermostatic switches primarily for use in equipment for
IEC-389-1/1972 telecommunication and in electronic applications employing similar
techniques.
General requirements and measuring methods.
(Withdrawn)
269. PS-1323/1974 Dimensions of spindle ends for manually operated electronic
IEC-390/1972 components.
(Withdrawn)
 20

270. PS-1324/1974 Guide for the drafting of specifications for microwave ferrites.
IEC-392/1972 (Withdrawn)

271. PS-1325/1974 Information on ferrite materials appearing in manufacturers

IEC-401/1972 catalogues of transformer and inductor cores.
(Withdrawn & superseded by PS-3155/1992)
272. PS-1326/1974 Simplified method for pressure calibration of one-inch condense
IEC-402/1972 microphones by the reciprocity technique. (Withdrawn)
273. PS-1327/1974 Audio frequency generators.
IEC-403/1972 (Withdrawn)
274. PS-2111(55)/1990 Electrotechnical Vocabulary. Chapter-55. Telegraphy and telephony.
(Withdrawn)
275. PS-2111(60)/1998 Electrotechnical Vocabulary. Radiocommunications.
IEC-50(60)/1970 (Withdrawn)
276. PS-2111(301)/1998 Electrotechnical Vocabulary.
IEC-50(301)/1983 Chapter 301: General terms on measurements in electricity-
Chapter 302: Electrical measuring Instruments-
Chapter 303: Electronic measuring instruments.
(Withdrawn)
277. PS-2111(371)/1990 Electrotechnical Vocabulary. Chapter-371. Telecontrol.
IEC-50(371)/1984 (Withdrawn)
278. PS-2111(521)/1990 Electrotechnical Vocabulary.
IEC-50(521)/1984 Chapter-521: Semiconductor devices and integrated circuits.
(Replaced PS-301/1963)
(Withdrawn)
279. PS-2111(531)/1990 Electrotechnical Vocabulary.
IEC-50(531)/1974 Chapter-531: Electronic tubes. (Replaced PS-301/1963)
(Withdrawn)
280. PS-2111(551)/1990 Electrotechnical Vocabulary-
IEC-50(551)/1982 Power electronics.
(Withdrawn & superseded by PS: IEC 60050(551)-2002)
281. PS-2111(581)/1990 Electrotechnical Vocabulary.
IEC-50(581)/1978 Chapter-581: Electromechanical components for electronic
equipment.
(Withdrawn)
282. PS-2111(701)/1990 Electrotechnical Vocabulary.
IEC-50(701)/1988 Chapter-701: Telecommunications, channels and networks.
(Withdrawn)
283. PS-2111(702)/1998 Electrotechnical Vocabulary.
IEC-50(702)/1992 Chapter 702: Oscillations, signals and related devices.
(Withdrawn)
284. PS-2111(712)/1998 Electrotechnical Vocabulary.
IEC-50(712)/1992 Chapter 712: Antennas.
(Withdrawn)
285. PS-2111(714)/1998 Electrotechnical Vocabulary.
IEC-50(714)/1992 Chapter 714: Switching and signalling in telecommunications.
 21

(Withdrawn)
286. PS-2111(715)/1998 Electrotechnical Vocabulary.
IEC-50(715)/1996 Chapter 715: Telecommunication networks, teletraffic and operation.
(Withdrawn)
287. PS-2111(716-1)/1998 Electrotechnical Vocabulary.
IEC-50(716-1)/1995 Chapter 716-1: Integrated services digital network (ISDN)-
Part 1: General aspects.
(Withdrawn)
288. PS-2111(721)/1998 Electrotechnical Vocabulary.
IEC-50(721)/1991 Chapter 721: Telegraphy, facsimile and data communication.
(Withdrawn)
289. PS-2111(722)/1998 Electrotechnical Vocabulary.
IEC-50(722)/1993 Chapter 722: Telephony.
(Withdrawn)
290. PS-2111(725)/1990 Electrotechnical Vocabulary.
IEC-50(725)/1982 Chapter-725: Space radiocommunications.
(Withdrawn)
291. PS-2111(726)/1990 Electrotechnical Vocabulary.
IEC-50(726)/1982 Chapter-726: Transmission lines and waveguides.
(Replaced PS-315/1963)
(Withdrawn)
292. PS-2111(731)/1998 Electrotechnical Vocabulary.
IEC-50(731)/1991 Chapter 731: Optical fibre communication.
(Withdrawn)
293. PS-2111(801)/1990 Electrotechnical Vocabulary-
IEC-50(801)/1984 Chapter 801: Acoustics and electroacoustics.
(Withdrawn & superseded by PS: IEC 60050(801)-2002)
294. PS-2111(806)/1990 Electrotechnical Vocabulary.
IEC-50(806)/1975 Chapter-806: Recording and reproduction of sound and video.
(Replaced PS-302/1963)
(Withdrawn)
295. PS-2111(881)/1990 Electrotechnical Vocabulary.
IEC-50(881)/1983 Chapter-881: Radiology and radiological physics.
(Replaced PS-316/1963)
(Withdrawn)
296. PS-2111(901)/1990 Electrotechnical Vocabulary. Chapter-901: Magnetism.
(Replaced PS-1081/1974)
(Withdrawn)
297. PS-2111(902)/1990 Electrotechnical Vocabulary.
IEC-50(902)/1973 Chapter-902: Radio-interference.
(Withdrawn)
298. PS-2340/1989 General principles for the creation of graphical symbols for use on
equipment.
(Based on IEC-416/1988)
299. PS-2341-1/1989 Diagrams, charts, tables. Part 1: Definitions and classification.
(Based on IEC-113-1/1971)
 22

300. PS-2341-3/1990 Diagrams, charts, tables.

Part 3: General recommendations for the preparation of diagrams.
(Based on IEC-113-3/1974)
301. PS-2341-5/1990 Diagrams, charts, tables.
Part 5: Preparation of interconnection diagrams and tables.
(Based on IEC-113-5/1975)
302. PS-2341-6/1990 Diagrams, charts, tables.
Part 6: Preparation of unit wiring diagrams and tables.
(Based on IEC-113-6/1976)
303. PS-2341-7/1992 Diagrams, charts, tables. Part 7: Preparation of logic diagrams.
(Based on IEC-113-7/1981)
304. PS-2342-1/1990 Graphical symbols for diagrams-
IEC-617-1/1985 Part-1: General information, general index. Cross reference tables.
(Withdrawn)
305. PS-2342-2/1991 Graphical symbols for diagrams.
Part 2: Symbol elements qualifying symbols and other symbols
having general application.
(Based on IEC-617-2/1983)
306. PS-2342-3/1990 Graphical symbols for diagrams.
Part 3: Conductors and connecting devices.
(Based on IEC-617-3/1983)
307. PS-2342-4/1999 Graphical symbols for diagrams-
Part 4: Basic passive components. (1st Revision)
(Based on IEC-617-4/1996)
308. PS-2342-5/1994 Graphical symbols for diagrams.
Part 5: Semiconductors and electron tubes.
(Based on IEC-617-5/1983)
309. PS-2342-8/1991 Graphical symbols for diagrams.
Part 8: Measuring instruments, lamps and signalling devices.
(Based on IEC-617-8/1983)
310. PS-2342-9/1993 Graphical symbols for diagrams.
Part 9: Telecommunications: Switching and peripheral equipment.
(Based on IEC-617-9/1983)
311. PS-2342-10/1996 Graphical symbols for diagrams.
Part 10: Telecommunications: Transmission.
(Based on IEC-617-10/1983)

312. PS-2342-11/1994 Graphical symbols for diagrams.

Part 11: Architectural and topographical installation plans
and diagrams.
(Based on IEC-617-11/1983)
313. PS-2342-12/1992 Graphical symbols for diagrams-
IEC-617-12/1991 Part-12: Binary logic elements.
(Withdrawn)
314. PS-2342-13/1992 Graphical symbols for diagrams. Part 13: Analogue elements.
 23

(Based on IEC-617-13/1978)
315. PS-2343-1/1989 Stabilized power supplies, d. c. output. Part 1: Terms and definitions.
(Based on IEC-478-1/1974)
316. PS-2343-2/1991 Stabilized power supplies, d. c. output. Part 2: Rating and
performance.
(Based on IEC-478-2/1986)
317. PS-2343-3/1994 Stabilized power supplies, d. c. output.
Part 3: Reference levels and measurement of conducted
electromagnetic interference (EMI). (1st Revision)
(Based on IEC-478-3/1989)
318. PS-2343-4/1990 Stabilized power supplies, d. c. output.
Part 4: Tests other than radio-frequency interference.
(Based on IEC-478-4/1976)
319. PS-2343-5/1997 Stabilized power supplies, d. c. output- Part 5: Measurement of the
magnetic component of the reactor near field.
(Based on IEC-478-5/1993)
320. PS-2344-1/1989 Analogue signals for process control systems.
Part 1: Direct current signals.
(Based on IEC-381-1/1982)
321. PS-2344-2/1989 Analogue signals for process control systems.
Part 2: Direct voltage signals.
(Based on IEC-381-2/1978)
322. PS: 2345-1/1992 Semiconductor devices –
Part 1: General.
(Withdrawn & superseded by PS-2345-1/2014)

PS: 2345-1/2014 Semiconductor devices –

Part 1: General. (1st Revision)
(Based on IEC-60747-1/2010)
323. PS-2345-2/1998 Semiconductor devices- Discrete devices-
IEC-747-2/1983 Part 2: Rectifier diodes.
(Withdrawn)
324. PS-2345-2-1/1998 Semiconductor devices- Discrete devices-
IEC-747-2-1/1989 Part 2: Rectifier diodes. Section One: Blank detail specification
for rectifier diodes (including avalanche rectifier diodes),
ambient and case- rated, up to 100 A.
(Withdrawn)

325. PS-2345-2-2/1998 Semiconductor devices- Discrete devices-

IEC-747-2-2/1993 Part 2: Rectifier diodes. Section Two: Blank detail specification
for rectifier diodes (including avalanche rectifier diodes),
ambient and case- rated, for currents greater than 100 A.
(Withdrawn)
326. PS-2345-3/1998 Semiconductor devices- Discrete devices-
IEC-747-3/1985 Part 3: Signal (including switching) and regulator diodes.
(Withdrawn)
 24

327. PS-2345-3-1/1990 Semiconductor devices. Discrete devices.

Part 3: Signal (including switching) and regulator diodes:
Section One: Blank detail specification for signal diodes,
switching diodes and controlled-avalanche diodes.
(Based on IEC-747-3-1/1986)
328. PS-2345-3-2/1990 Semiconductor devices. Discrete devices.
Part 3: Signal (including switching) and regulator diodes:
Section Two: Blank detail specification for voltage regulator diodes
and voltage-reference diodes, excluding temperature-compensated
precision reference diodes.
(Based on IEC-747-3-2/1986)
329. PS-2345-4/1998 Semiconductor devices- Discrete devices-
IEC-747-4/1991 Part 4: Microwave diodes and transistors.
(Withdrawn)
330. PS-2345-5/1989 Semiconductor devices. Discrete devices.
Part 5: Optoelectronic devices.
(Based on IEC-747-5/1984)
331. PS-2345-6/1997 Semiconductor devices. Discrete devices-
IEC-747-6/1983 Part 6: Thyristors -Section One: Blank detail specification for reverse
blocking triode thyristors, ambient and case-rated, up to 100 A.
(Based on IEC-747-6-1/1989)
(Withdrawn)
332. PS-2345-6-1/1997 Semiconductor devices- Discrete devices-
Part 6: Thyristors - Section Three: Blank detail specification
for reverse blocking triode thyristors, ambient and case- rated,
for currents greater than 100 A.

333. PS-2345-6-3/1998 Semiconductor devices- Discrete devices-

IEC-747-6-3/1993 Part 6: Thyristors - Section Three: Blank detail specification
for reverse blocking triode thyristors, ambient and case- rated,
for currents greater than 100 A.
(Withdrawn)
334. PS-2345-7/1998 Semiconductor devices- Discrete devices-
IEC-747-7/1988 Part 7: Bipolar transistors.
(Withdrawn)

335. PS-2345-7-1/1998 Semiconductor devices- Discrete devices-

IEC-747-7-1/1989 Part 7: Bipolar transistors- Section One: Blank detail specification for
ambient-rated bipolar transistors for low and high-frequency
amplification.
(Withdrawn)

336. PS-2345-7-2/1998 Semiconductor devices- Discrete devices-

IEC-747-7-2/1989 Part 7: Bipolar transistors- Section Two: Blank detail specification
 25

for case-rated bipolar transistors for low-frequency amplification.

(Withdrawn)

337. PS-2345-7-3/1998 Semiconductor devices- Discrete devices-

IEC-747-7-3/1991 Part 7: Bipolar transistors- Section Three: Blank detail specification
for bipolar transistors for switching applications. (Withdrawn)
338. PS-2345-7-4/1998 Semiconductor devices- Discrete devices-
IEC-747-7-4/1991 Part 7: Bipolar transistors- Section Four: Blank detail specification
for case-rated bipolar transistors for high-frequency amplification.
(Withdrawn)
339. PS-2345-8/1991 Semiconductor devices. Discrete devices.
Part 8: Field-effect transistors.
(Based on IEC-747-8/1984)
340. PS-2345-8-1/1991 Semiconductor devices. Discrete devices.
Part 8-1: Field-effect transistors. Section One- Blank detail
specification for single-gate field-effect transistors up to 5 W and 1
GHz.
(Based on IEC-747-8-1/1987)
341. PS-2345-8-2/1998 Semiconductor devices- Discrete devices-
IEC-747-8-2/1993 Part 8: Field-effect transistors- Section Two: Blank detail
specification for field-effect transistors for case-rated power
amplifier applications.
(Withdrawn)
342. PS-2345-8-3/1998 Semiconductor devices- Discrete devices-
IEC-747-8-3/1995 Part 8: Field-effect transistors- Section Three: Blank detail
specification for case-rated field-effect transistors for switching
applications.
(Withdrawn)
343. PS-2345-10/1990 Semiconductor devices. Discrete devices.
IEC-747-10/1984 Part-10: Generic specification for discrete devices and integrated
circuits.
(Withdrawn)
344. PS-2345-11/1990 Semiconductor devices. Discrete devices.
IEC-747-11/1985 Part-11: Sectional specification for discrete devices.
(Withdrawn)
345. PS-2345-12/1998 Semiconductor devices- Part 12: Sectional specification for
IEC-747-12/1991 optoelectronic devices.
(Withdrawn)
346. PS-2345-12-1/1998 Semiconductor devices- Part 12: Optoelectronic devices-
IEC-747-12-1/1995 Section 1: Blank detail specification for light emitting / infrared
emitting diodes with / without pigtail for fibre optic systems and
sub-systems.
(Withdrawn)
347. PS-2345-12-2/1998 Semiconductor devices- Part 12: Optoelectronic devices-
IEC-747-12-2/1995 Section 2: Blank detail specification for laser diode modules with pigtail
for fibre optic systems and sub-systems.
 26

348. PS-2345-12-4/1999 Semiconductor devices – Part –12-4: Optoelectronic devices.

Blank detail specification for pin-FET Modules with / without
pigtail, for fibre optic systems or sub-systems.
(Based on IEC-747-12-4/1997)
349. PS-2345-12-5/1999 Semiconductor devices – Part-12-5: Optoelectronic devices –
Blank detail specification for pin – Photodiodes with / without
pigtail for fibre optic systems or subsystems.
(Based on IEC-747-12-5/1997)
350. PS-2345-12-6/1999 Semiconductor devices – Part-12-6: Optoelectronic devices – Blank
detail specification for avalanche photodiodes with /without pigtail
for fibre optic systems or sub systems.
(Based on IEC-747-12-6/1997)
351. PS-2345-14-1/2012 Semiconductor devices – Part 14-1: Semiconductor sensors –
Generic specification for sensors.
(Based on IEC-60747-14-1/2010)
352. PS-2345-14-3/2012 Semiconductor devices – Part 14-3: Semiconductor sensors –Pressure
sensors.
(Based on IEC-60747-14-3/2009)

353. PS-2346/1996 Grid systems for printed circuits. (1st Revision)

(Based on IEC-97/1991)
(Replaced PS: 2346/1989)
354. PS-2347/1989 Terms and definitions for printed circuits.
IEC-194/1988 (Replaced PS-1189/1974)
(Withdrawn)
355. PS-2348-1/1989 Base materials for printed circuits.
IEC-249-1/1982 Part-1: Test methods.
(Replaced PS-1230/1974)
(Withdrawn & superseded by PS: IEC 249-1/2002)
356. PS-2348-2-1/1989 Base materials for printed circuits.
IEC-249-2-1/1985 Part-2: Specifications.
Specification 1: Phenolic cellulose paper copper-clad
laminated sheet high electrical quality.
(Replaced PS-1231/1974)
(Withdrawn)

357. PS-2348-2-2/1989 Base materials for printed circuits. Part-2: Specifications.

IEC-249-2-2/1985 Specification 2: Phenolic cellulose paper copper-clad
laminated sheet, economic quality.
(Replaced PS-1231/1974)
(Withdrawn)
358. PS-2348-2-3/1989 Base materials for printed circuits.
IEC-249-2-3/1987 Part-2: Specifications.
Specification 3: Epoxide cellulose paper copper-clad
 27

laminated sheet of defined flammability (vertical burning test).

(Replaced PS-1231/1974)
(Withdrawn)
359. PS-2348-2-4/1999 Base materials for printed circuits –
IEC:249-2-4/87 Part-2: Specifications. Specification No.4: Epoxide woven
glass fabric copper-clad laminated sheet, general purpose grade.
(Replaced PS-1231/1974)
(Withdrawn)
360. PS-2348-2-5/1999 Base materials for printed circuits:
IEC:249-2-5/87 Part 2: Specifications. Specification No. 5: Epoxide woven
glass fabric copper-clad laminated sheet of defined
flammability (vertical burning test).
(Replaced PS-1231/1974)
(Withdrawn)
361. PS-2348-2-6/1999 Base materials for printed circuits.
IEC:249-2-6/85 Part 2: Specifications. Specification No. 6: Phenolic
cellulose paper copper-clad laminated sheet of
defined flammability (horizontal burning test).
(Replaced PS-1231/1974)
(Withdrawn)
362. PS-2348-2-7/1989 Base materials for printed circuits.
IEC-249-2-7/1987 Part-2: Specifications.
Specification 7: Phenolic cellulose paper copper-clad laminated
sheet of defined flammability (vertical burning test).
(Replaced PS-1231/1974)
(Withdrawn)
363. PS-2348-2-8/1989 Base materials for printed circuits.
IEC-249-2-8/1987 Part-2: Specifications.
Specification 8: Flexible copper-clad polyester (PETP) film.
(Replaced PS-1231/1974)
(Withdrawn)
364. PS-2348-2-9/1989 Base materials for printed circuits.
IEC-249-2-9/1987 Part-2: Specifications.
Specification 9: Epoxide cellulose paper core, epoxide glass cloth
surface copper-clad laminated sheet of defined flammability (vertical
burning test).
(Replaced PS-1231/1974)
(Withdrawn)
365. PS-2348-2-10/1989 Base materials for printed circuits.
IEC-249-2-10/1987 Part-2: Specifications.
Specification 10: Epoxide non-woven / woven glass reinforced
copper-clad laminated sheet of defined flammability (vertical
burning test).
(Replaced PS-1231/1974)
(Withdrawn)
366. PS-2348-2-11/1989 Base materials for printed circuits.
 28

IEC-249-2-11/1987 Part-2: Specifications.

Specification 11: Thin epoxide woven glass fabric copper-clad
laminated sheet general purpose grade for use in the fabrication
of multi layer printed boards.
(Replaced PS-1231/1974)
(Withdrawn)
367. PS-2348-2-12/1989 Base materials for printed circuits.
IEC-249-2-12/1987 Part-2: Specifications.
Specification 12: Thin epoxide woven glass fabric copper-clad
laminated sheet of defined flammability, for use in the fabrication of
multi layer printed boards.
(Replaced PS-1231/1974)
(Withdrawn)
368. PS-2348-2-13/1989 Base materials for printed circuits.
IEC-249-2-13/1987 Part-2: Specifications.
Specification 13: Flexible copper-clad polyimide film, general
purpose grade.
(Replaced PS-1231/1974)
(Withdrawn)
369. PS-2348-2-14/1999 Base materials for printed circuits.
IEC:249-2-14/88 Part 2: Specifications. Specification No. 14: Phenolic cellulose
paper copper-clad laminated sheet of defined flammability (vertical
burning test), economic quality.
(Replaced PS-1231/1974)
(Withdrawn)
370. PS-2348-2-15/1989 Base materials for printed circuits.
IEC-249-2-15/1987 Part-2: Specifications. Specification No.15:
Flexible copper-clad polyimide film of defined flammability.
(Replaced PS-1231/1974)
(Withdrawn)
371. PS-2348-2-16/1999 Base materials for printed circuits –
IEC:249-2-16/92 Part 2: Specifications. Specification No. 16. Polyimide
woven glass fabric copper-clad laminated sheet
of defined flammability. (vertical burning test).
(Replaced PS-1231/1974)
(Withdrawn)

372. PS-2348-2-17/1999 Base materials for printed circuits –

IEC:249-2-17/92 Part 2: Specifications – Specification No. 17: Thin polyimide woven glass
fabric copper-clad laminated sheet of defined flammability for use in the
fabrication of multilayer printed boards.
(Replaced PS-1231/1974)
(Withdrawn)
373. PS-2348-2-18/1999 Base materials for printed circuits –
IEC:249-2-18/92 Part 2: Specifications.- Specification No. 18:Bismaleimide / triazine
 29

modified epoxide woven glass fabric copper-clad laminated sheet of

defined flammability (vertical burning test).
(Replaced PS-1231/1974)
(Withdrawn)
374. PS-2348-2-19/1999 Base material for printed circuits –
IEC:249-2-19/92 Part 2: Specifications-Specification No.19:Thin bismaleimide /
triazine modified epoxide woven glass fabric copper-clad laminated
sheet of defined flammability for use in the fabrication of multilayer
printed boards.
(Replaced PS-1231/1974)
(Withdrawn)
375. PS-2348-3-1/1989 Base materials for printed circuits.
IEC-249-3-1/1981 Part-3: Special materials used in connection with printed circuits.
Specification 1: Prepreg for use as bonding sheet material in the
fabrication of multi layer printed boards.
(Replaced PS-1232/1974)
(Withdrawn)
376. PS-2348-3-3/1999 Base materials for printed circuits –
IEC:249-3-3/91 Part 3: Special materials used in connection with printed circuits –
Specification No. 3: Permanent polymer coating materials (solder
resist) for use in the fabrication of printed boards.
(Replaced PS-1232/1974)
(Withdrawn)
377. PS-2349-1/1989 Printed boards.
IEC-326-1/1984 Part-1: General information for the specification writer.
(Replaced PS-1295/1974)
(Withdrawn)
378. PS-2349-2/1989 Printed boards-
IEC-326-2/1976 Part 2: Test methods.
(Replaced PS-1295/1974)
(Withdrawn)
379. PS-2349-3/1989 Printed boards.
IEC-326-3/1980 Part-3: Design and use of printed boards.
(Withdrawn)
380. PS-2349-5/1999 Printed boards Part 5: Specification for single and double sided
IEC:326-5/80 printed boards with plated-through holes.
(Withdrawn)

381. PS-2349-7/1994 Printed boards. Part 7: Specification for single and double sided
IEC-326-7/1981 flexible printed boards without through connections.
(Based on IEC-326-7/1981)
(Withdrawn)
382. PS-2349-8/1995 Printed boards. Part 8: Specification for single and double sided
IEC-326-8/1981 flexible printed boards with through connections.
(Based on IEC-326-8/1981)
(Withdrawn)
 30

383. PS-2349-9/1999 Printed boards – Part 9: Specification for flexible multilayer printed
IEC:326-9/91 boards with through connections.
(Withdrawn)
384. PS-2349-10/1999 Printed boards - Part 10: Specification for flex-rigid double-sided
IEC:326-10/91 printed boards with through connections.
(Withdrawn)
385. PS-2349-11/1999 Printed boards - Part 11: Specification for flex-rigid multilayer
IEC:326-11/91 printed boards with through connections.
(Withdrawn)
386. PS-2349-12/1999 Printed boards - Part 12: Specification for mass lamination panels
IEC:326-12/92 (semi -manufactured multilayer printed boards).
(Withdrawn)
387. PS-2898/1990 Recommended methods of measurement of radiated and
IEC-106/1974 conducted interference from receivers for amplitude-
modulation, frequency modulation and television broadcast
transmissions.
(Replaced PS-1049/1974)
(Withdrawn)
388. PS-2899-1-1/1998 Semiconductor convertors - General requirements and line
IEC-146-1-1/1991 commutated convertors- Part 1-1: Specification for basic
requirements.
(Withdrawn)
389. PS-2899-1-2/1998 Semiconductor convertors - General requirements and line
IEC-146-1-2/1991 commutated convertors- Part 1-2: Application guide.
(Withdrawn)
390. PS-2899-1-3/1998 Semiconductor convertors. General requirements and line
IEC-146-1-3/1991 commutated convertors- Part 1-3: Transformers and reactors.
(Withdrawn)
391. PS-2899-2/1990 Semiconductor convertors.
Part 2: Semiconductor self-commutated convertors.
(Based on IEC-146-2/1974)
392. PS-2899-3/1991 Semiconductor convertors.
Part 3: Semiconductor direct d. c. convertors (d. c. chopper
convertors)
(Based on IEC-146-3/1977)
393. PS-2899-4/1990 Semiconductor convertors-
IEC-146-4/1986 Part-4: Method of specifying the performance and test
requirement of uninterruptible power system.
(Replaced PS-1111/1974)
(Withdrawn)
394. PS-2899-5/1991 Semiconductor convertors. Part 5: Switches for uninterruptible
power systems (UPS switches)
(Based on IEC-146-5/1988)
395. PS-2899-6/1996 Semiconductor convertors. Part 6: Application guide for the
protection of semiconductor convertors against over current by fuses.
(Based on IEC-146-6/1992)
 31

396. PS-2900/1990 Terminology for high voltage direct current transmission.

IEC-633/1978 (Withdrawn)
397. PS-2901/1990 Testing of semiconductor valves for high voltage d.c. power
IEC-700/1981 transmission.
(Withdrawn)
398. PS-2902/1990 Method of evaluating the performance of transmitters for use in
IEC-770/1984 industrial-process control systems.
(Replaced PS-2199/1989)
(Withdrawn)
399. PS-2902-2/1998 Transmitters for use in industrial-process control system-
IEC-770-2/1989 Part 2: Guidance for inspection and routine testing.
(Withdrawn)
400. PS-2903/1990 Industrial-process measurement and control-
IEC-902/1987 Terms and definitions.
(Withdrawn)
401. PS-2904-1/1990 Potentiometers-
IEC-393-1/1989 Part-1: Terms and methods of test.
(Withdrawn)
402. PS-2904-2/1990 Potentiometers-
IEC-393-2/1976 Part-2: Sectional specification:
Lead-screw actuated preset potentiometers. Selection of methods of
test and general requirements.
(Withdrawn & superseded by PS-3541-2/1994)
403. PS-2904-3/1990 Potentiometers-
IEC-393-3/1977 Part-3: Sectional specification:
Single turn rotary wirewound precision potentiometers.
Selection of methods of test and general requirements.
(Withdrawn & superseded by PS-3541-3/1994)
404. PS-2904-4/1990 Potentiometers- Part-4: Sectional specification:
IEC-393-4/1978 Single turn rotary power potentiometers.
Selection of methods of test and general requirements.
(Withdrawn & superseded by PS-3541-4/1995)
405. PS-2904-5/1990 Potentiometers-
IEC-393-5/1978 Part-5: Sectional specification:
Single turn rotary low-power wirewound and non-wirewound
potentiometers. Selection of methods of test and general
requirements. (Withdrawn)
406. PS-2905-1/1990 Plastic film dielectric rotary variable tuning capacitors
IEC-415-1/1973 Grade 2. Part-1: General requirements for tests and measuring
methods.
(Withdrawn)
407. PS-2906-1/1990 Variable capacitors-
IEC-418-1/1974 Part-1: Terms and method of test.
(Withdrawn)
408. PS-2907/1990 Guide for the choice of colours to be used for the marking of
 32

IEC-425/1973 capacitors and resistors.

(Withdrawn)
409. PS-2908/1990 Method of measurement of non-linearity in resistors.
IEC-440/1973 (Withdrawn)
410. PS-2909-1/1990 Ceramic dielectric disk-style rotary variable preset capacitor:
IEC-499-1/1974 Grade-2. Part 1: General requirements for tests and measuring
methods.
(Withdrawn)
411. PS-2910/1990 Method for the determination of the space required by capacitors and
IEC-717/1981 resistors with unidirectional terminations.
(Withdrawn)
412. PS-2911-1/1990 Semiconductor devices. Integrated circuits. Part 1: General.
IEC-748-1/1984 (Based on IEC-748-1/1984)
(Withdrawn)
413. PS-2911-2/1990 Semiconductor devices. Integrated circuits.
IEC-748-2/1985 Part-2: Digital integrated circuits.
(Withdrawn)
414. PS-2911-2-1/1998 Semiconductor devices- Integrated circuits- Part 2: Digital
IEC-748-2-1/1991 integrated circuits- Section One: Blank detail specification for
bipolar monolithic digital integrated circuit gates (excluding
Uncommitted logic arrays).
(Withdrawn)
415. PS-2911-2-2/1998 Semiconductor devices- Integrated circuits- Part 2: Digital
IEC-748-2-2/1992 integrated circuits- Section Two: Family specification for HCMOS
digital integrated circuits, (series 54/74 HC, 54/74 HCT, 54/74 HCU).
(Withdrawn)
416. PS-2911-2-3/1998 Semiconductor devices- Integrated circuits- Part 2: Digital
IEC-748-2-3/1992 integrated circuits- Section Three: Blank detail specification for
HCMOS digital integrated circuits (series 54/74 HC, 54/74 HCT,
54/74 HCU).
(Withdrawn)
417. PS-2911-2-4/1998 Semiconductor devices- Integrated circuits- Part 2: Digital
IEC-748-2-4/1992 integrated circuits- Section Four: Family specification for
complementary MOS digital integrated circuits, (series 4000 B and
4000 UB).
(Withdrawn)

418. PS-2911-2-5/1998 Semiconductor devices- Integrated circuits- Part 2: Digital

IEC-748-2-5/1992 integrated circuits- Section Five: Blank detail specification for
complementary MOS digital integrated circuits (series 4000 B
and 4000 UB).
(Withdrawn)
419. PS-2911-2-6/1998 Semiconductor devices- Integrated circuits- Part 2: Digital
IEC-748-2-6/1991 integrated circuits- Section Six: Blank detail specification for
microprocessor integrated circuits.
 33

(Withdrawn)
420. PS-2911-2-7/1998 Semiconductor devices- Integrated circuits- Part 2: Digital
IEC-748-2-7/1992 integrated circuits- Section Seven: Blank detail specification for
integrated circuit fusible-link programmable bipolar read-only
memories.
(Withdrawn)
421. PS-2911-2-8/1998 Semiconductor devices- Integrated circuits- Part 2: Digital
IEC-748-2-8/1993 integrated circuits- Section Eight: Blank detail specification for
integrated circuit static read / write memories.
(Withdrawn)
422. PS-2911-2-9/1998 Semiconductor devices- Integrated circuits- Part 2: Digital
IEC-748-2-9/1994 integrated circuits- Section 9: Blank detail specification for MOS
ultraviolet light erasable electrically programmable read-only
memories.
(Withdrawn)
423. PS-2911-2-10/1998 Semiconductor devices- Integrated circuits-
IEC-748-2-10/1994 Part 2: Digital
integrated circuits- Section 10: Blank detail specification for
integrated circuit dynamic read / write memories.
(Withdrawn)
424. PS-2911-3/1990 Semiconductor devices. Integrated circuits.
IEC-748-3/1986 Part-3: Analogue integrated circuits.
(Withdrawn)
425. PS-2911-3-1/1998 Semiconductor devices- Integrated circuits-
IEC-748-3-1/1991 Part 3: Analogue integrated circuits-
Section One: Blank detail specification for monolithic integrated
operational amplifiers.
(Withdrawn)
426. PS-2911-4/1990 Semiconductor devices. Integrated circuits.
IEC-748-4/1987 Part-4: Interface integrated circuits.
(Withdrawn)
427. PS-2911-4-1/1998 Semiconductor devices- Integrated circuits- Part 4: Interface
IEC-748-4-1/1993 integrated circuits- Section 1: Blank detail specification for
linear digital-to-analogue converters (DAC).
(Withdrawn)
428. PS-2911-4-2/1998 Semiconductor devices- Integrated circuits- Part 4: Interface
IEC-748-4-2/1993 integrated circuits- Section 1: Blank detail specification for
linear analogue-to-digital converters (ADC). (Withdrawn)
429. PS-2911-11/1993 Semiconductor devices. Integrated circuits.
Part 11: Sectional specification for semiconductor integrated circuits
excluding hybrid circuits.
(Based on IEC-748-11/1990)
430. PS-2911-11-1/1998 Semiconductor devices- Integrated circuits-
IEC-748-11-1/1992 Part 11:Section 1: Internal visual examination for semiconductor
integrated circuits excluding hybrid circuits.
(Withdrawn)
 34

431. PS-2911-20/1994 Semiconductor devices. Integrated circuits.

Part 20: Generic specification for film integrated circuits
and hybrid film integrated circuits.
(Based on IEC-748-20/1988)
432. PS-2911-20-1/1998 Semiconductor devices- Integrated circuits- Part 20:
IEC-748-20-1/1994 Generic specification for film integrated circuits and hybrid
film integrated circuits- Section 1: Requirements for internal
visual examination.
(Withdrawn)
433. PS-2911-21/1995 Semiconductor devices. Integrated circuits. Part 21: Sectional
IEC-748-21/1991 specification for film integrated circuits and hybrid film
integrated circuits on the basis of qualification approval procedures.
(Based on IEC-748-21/1991)
(Withdrawn)
434. PS-2911-21-1/1995 Semiconductor devices. Integrated circuits. Part 21-1: Section One:
IEC-748-21-1/1991 Blank detail specification for film integrated circuits and hybrid
film integrated circuits on the basis of qualification approval
procedures.
(Based on IEC-748-21-1/1991)
(Withdrawn)
435. PS-2911-22/1998 Semiconductor devices- Integrated circuits- Part 22:
IEC-748-22/1997 Sectional specification for film integrated circuits and hybrid
film integrated circuits on the basis of the capability approval
procedures.
(Withdrawn)
436. PS-2911-22-1/1998 Semiconductor devices- Integrated circuits- Part 22-1:
IEC-748-22-1/1997 Blank detail specification for film integrated circuits and hybrid
. film integrated circuits on the basis of the capability approval
procedures.
(Withdrawn)
437. PS-2912/1990 Safety requirements for radio transmitting equipment.
(Replaced PS-1197/1974)
(Based on IEC-215/1987)
438. PS-2996-1/1991 Aerials for the reception of sound and television
broadcasting in the frequency range 30 MHz to 1 GHz.
Part 1: Electrical and mechanical characteristics.
(Based on IEC-597-1/1977)

439. PS-2996-2/1992 Aerials for the reception of sound and television

broadcasting in the frequency range 30 MHz to 1 GHz.
Part 2: Methods of measurement of electrical performance
parameters.
(Replaced PS-1108/1974)
(Based on IEC-597-2/1977)
440. PS-2996-3/1992 Aerials for the reception of sound and television
broadcasting in the frequency range 30 MHz to 1 GHz.
 35

Part 3: Methods of measurement of mechanical properties, vibration

and environmental tests.
(Replaced PS-1108/1974)
(Based on IEC-597-3/1983)
441. PS-2996-4/1992 Aerials for the reception of sound and television
broadcasting
P in the frequency range 30 MHz to 1 GHz.
Part 4: Guide for the preparation of aerial performance
specifications- Detailed specification sheet format.
(Replaced PS-1108/1974)
(Based on IEC-597-4/1983)

442. PS-2997-1/1991 Solderless connections.

Part 1: Solderless wrapped connections.
General requirements, test methods and practical guidance.
(Replaced PS-1310/1974)
(Based on IEC-352-1/1983)
443. PS-2998/1991 Characteristic impedances and dimensions of radio-frequency
coaxial cables.
(Replaced PS-1036/1974)
(Based on IEC-78/1967)
444. PS-3005/1991 Standard definitions and methods of measurement for piezoelectric
vibrators operating over the frequency range up to 30 MHz.
(Replaced PS-1266/1974)
(Based on IEC-302/1969)
445. PS-3006/1991 Portable X or gamma radiation exposure rate meters and monitors
for use in radiological protection.
(Based on IEC-395/1972)
446. PS-3007/1991 Dimensions for magnetic oxide cores intended for use in power
supplies (EC – cores)
(Based on IEC-647/1979)
447. PS-3008/1991 Stabilized power supplies, a. c. output.
(Based on IEC-686/1980)
448. PS: 3143-1/1992 Fibre optic branching devices- Part-1: Generic specification.
(Withdrawn & superseded by PS-3143-1/2014)

PS: 3143-1/2014 Fibre optic interconnecting devices and passive components –

Non-wavelength- selective fibre optic branching devices –
Part 1: Generic specification.
(1st Revision).
(Based on IEC-60875-1/2010)
449. PS-3143-2/1993 Fibre optic branching devices.
Part 2: Sectional specification: Transmission star coupler.
(Based on IEC-875-2/1986)
450. PS-3144-3/1992 Push-button switches.
Part 3: Push-button switches of the multi-cell type.
(Replaced PS-1306/1974)
 36

(Based on IEC-341-3/1978)
451. PS-3145-1/1992 Connectors for frequencies below 3 MHz for use with
printed boards.
Part 1: General rules and guide for the preparation of detail
specification.
(Based on IEC-603-1/1981)
452. PS-3145-2/1993 Connectors for frequencies below 3 MHz for use with printed
boards.
Part 2: Two-part connectors or printed boards for basic grid of
2.54 mm (0.1 in) with common mounting features.
(Based on IEC-603-2/1988)
453. PS-3145-3/1994 Connectors for frequencies below 3 MHz for use with printed
boards.
Part 3: Two-part connectors for printed boards having contacts
spaced at 2.54 mm (0.1 in) centers and staggered terminations at that
same spacing.
(Based on IEC-603-3/1987)
454. PS-3145-4/1994 Connectors for frequencies below 3 MHz for use with printed
boards.
Part 4: Two-part connectors for printed boards having contacts
spaced at 1.91 mm (0.075 in) centers and staggered terminations
at that same spacing.
(Based on IEC-603-4/1987)
455. PS-3146/1992 Dimensions of copper conductors in local cables.
(Based on IEC-488/1974)
456. PS-3147/1992 Calculation of maximum external diameter of cables for indoor
installations.
(Based on IEC-649/1979)
457. PS-3148-1/1992 Quartz crystal units for frequency control and selection.
Part 1: Standard values and test conditions.
(Replaced PS-1077/1974)
(Based on IEC-122-1/1976)
458. PS-3148-2/1998 Quartz crystal units for frequency control and selection.
IEC-122-2/1983 Part 2: Guide to the use of quartz crystal units for frequency
control and selection.
(Replaced PS-1078/1974)
(Withdrawn)

459. PS-3148-2-1/1998 Quartz crystal units for frequency control and selection.
IEC-122-2-1/1991 Part 2: Guide to the use of quartz crystal units for frequency
control and selection.
Section One: Quartz crystal units for microprocessor clock supply.
(Withdrawn)
460. PS:3148-3/1992 Quartz crystal units for frequency control and selection.
Part 3: Standard outlines and pin connections.
(Withdrawn & superseded by PS-3148-3/2014)
 37

PS:3148-3/2014 Quartz crystal units of assessed quality –

Part 3: Standard outlines and lead connections. (2nd Revision)
(Based on IEC-60122-3/2010)
461. PS-3149/1998 Synthetic quartz crystal -
IEC-758/1993 Specifications and guide to the use. (1st Revision)
(Replaced PS-3149/1992)
(Withdrawn)
462. PS-3150/1992 Temperature control devices for frequency control and selection.
(Replaced PS-1274/1974)
(Based on IEC-314/1970)
463. PS-3151/1992 Dimensions of optical fibres.
(Based on IEC-693/1980)
464. PS-3152-1-1/1997 Optical Fibres –
Part 1: Generic specification- Section 1: General.
(Withdrawn & superseded by PS-3152-1-1/2013)

PS-3152-1-1/2013 Optical Fibres –

Part 1-1: Measurement methods and test procedures –
General and guidance. (1st Revision)
(Based on IEC-60793-1-1/2008)
465. PS-3152-2/1997 Optical fibres- Part 2: Product specifications. (1st Revision)
(Based on IEC-793-2/1992)
(Replaced PS-3152-2/1992)
466. PS-3153/1992 Hand and / or foot contamination monitors and warning assemblies.
(Based on IEC-504/1975)
467. PS-3154/1992 Installed exposure rate meters, warning assemblies and monitors
for X or gamma radiation of energy between 80 keV and 3 MeV.
(Based on IEC-532/1976)
468. PS-3155/1992 Information on ferrite materials appearing in manufacturers
catalogues of transformer and inductor cores.
(Replaced PS-1325/1974)
(Based on IEC-401/1972)
469. PS-3156/1992 Laminations for transformers and inductors for use in
telecommunication and electronic equipment.
(Based on IEC-740/1982)

470. PS-3351-1/1994 Piezoelectric filters. Part 1: General information, standard values

and test conditions.
(Replaced PS-1317/1974)
471. PS-3351-2-1/1995 Piezoelectric filters. Part 2: Guide to the use of piezoelectric filters.
Section One – Quartz crystal filters.
(Based on IEC-368-2-1/1988)
472. PS-3351-2-2/1998 Piezoelectric filters- Part 2: Guide to the use of piezoelectric filters-
IEC-368-2-2/1996 Section Two: Piezoelectric ceramic filters.
 38

(Withdrawn)
473. PS-3356/1993 Item designation in electrotechnology.
(Based on IEC-750/1983)
474. PS-3357/1993 Non-ionizing radiation hazards in the frequency range
from 10 MHz to 300000 MHz.
(Based on IEC-657/1979)
475. PS-3358-1/1993 Methods of measurement for radio equipment used in satellite earth
stations. Part 1: General.
(Based on IEC-510-1/1975)
476. PS-3358-1-2/1993 Methods of measurement for radio equipment used in satellite earth
stations.
Part 1: Measurements common to sub-systems and combinations of
sub-systems.
Section Two: Measurements in the r. f. range.
(Based on IEC-510-1-2/1984)
477. PS-3358-1-3/1993 Methods of measurement for radio equipment used in satellite earth
stations.
Part 1: Measurements common to sub-systems and combinations of
sub-systems.
Section Three: Measurements in the i.f. range.
(Based on IEC-510-1-3/1980)
478. PS-3358-1-4/1994 Methods of measurement for radio equipment used in satellite earth
stations.
Part 1: Measurements common to sub-systems and combinations of
sub-systems.
Section Four: Measurements in the base band.
(Based on IEC-510-1-4/1986)
479. PS-3358-1-5/1994 Methods of measurement for radio equipment used in satellite earth
stations.
Part 1: Measurements common to sub-systems and combinations of
sub-systems.
Section Five: Noise temperature measurements.
(Based on IEC-510-1-5/1988)
480. PS-3358-2-1/1997 Methods of measurement for radio equipment used in satellite
earth stations.
Part 2: Measurement for sub-systems.
Section One: General –
Section Two: Antenna (including feed network)
(Based on IEC-510-2-1/1978)
481. PS-3358-2-3/1998 Methods of measurement for radio equipment used in satellite
IEC-510-2-3/1989 earth stations.
Part 2: Measurements for sub-systems.
Section Three: Low noise amplifier.
(Withdrawn)
482. PS-3358-2-4/1995 Methods of measurement for radio equipment used in satellite
earth stations.
 39

Part 2: Measurements for sub-systems.

Section Four- Up and- down-convertors.
(Based on IEC-510-2-4/1988)
483. PS-3358-2-5/1995 Methods of measurement for radio equipment used in satellite
earth stations. Part 2: Measurements for sub-systems-
Section Five: Frequency modulators.
(Based on IEC-510-2-5/1992)
484. PS-3358-2-6/1996 Methods of measurement for radio equipment used in satellite
earth stations.
Part 2: Measurements for sub-systems-
Section six: Frequency demodulators.
(Based on IEC-510-2-6/1992)
485. PS-3358-2-7/1996 Methods of measurement for radio equipment used in satellite
earth stations.
Part 2: Measurements for sub-systems-
Section seven: High-power amplifier.
(Based on IEC-510-2-7/1989)
486. PS-3358-3-1/1997 Methods of measurement for radio equipment used in satellite
earth stations. Part 3: Methods of measurement on combinations
of sub-systems. Section One: General.
(Based on IEC-510-3-1/1981)
487. PS-3358-3-2/1999 Methods of measurement for radio equipment used in satellite
earth stations. Part 3: Methods of measurement on combinations of
sub-systems. Section Two: Measurement of the figure of merit
(G/T) of the receiving system in the 4 GHz to 6 GHz range.
(Based on IEC-510-3-2/1980)
488. PS-3358-3-3/1998 Methods of measurement for radio equipment used in satellite
IEC-510-3-3/1988 earth stations. Part 3: Methods of measurement on combinations
of sub-systems. Section Three: Measurements for monochrome
and colour television transmission.
(Withdrawn)
489. PS-3358-3-4/2001 Methods of measurement for radio equipment used in satellite
earth stations- Part 3: Methods of measurement of combinations of
sub-systems- Section Four: Measurements for frequency division
multiplex (f.d.m.) transmission.
(Based on IEC-510-3-4/1992)
490. PS-3359/1993 Semiconductor devices. Mechanical and climatic test methods.
(Based on IEC-749/1984)

491. PS-3359-14/2012 Semiconductor devices –Mechanical and climatic test methods –

Part 14: Robustness of terminations (lead integrity).
(Based on IEC-60749-14/2003)

492. PS-3360-1/1994 Magnetic tape sound recording and reproducing systems.

Part 1: General conditions and requirements.
(Replaced PS-1040/1974)
 40

(Based on IEC-94-1/1981)

493. PS-3360-2/1993 Magnetic tape sound recording and reproducing systems.

Part 2: Calibration tapes.
(Based on IEC-94-2/1975)

494. PS-3360-3/1994 Magnetic tape sound recording and reproducing systems.

Part 3: Methods of measuring the characteristics of recording and
reproducing equipment for sound on magnetic tape.
(Based on IEC-94-3/1979)

495. PS-3360-4/1995 Magnetic tape sound recording and reproducing systems.

Part 4: Mechanical magnetic tape properties.
(Based on IEC-94-4/1986)

496. PS-3360-5/1995 Magnetic tape sound recording and reproducing systems.

Part 5: Electrical magnetic tape properties.
(Based on IEC-94-5/1988)

497. PS-3360-6/1999 Magnetic tape sound recording and reproducing systems-

IEC: 94-6/1985 Part 6: Reel to reel systems.
(Withdrawn)
498. PS-3360-7/1999 Magnetic tape sound recording and reproducing systems-
IEC: 94-7/1986 Part 7: Cassette for commercial tape records and domestic use.
(Withdrawn)
499. PS-3360-8/1996 Magnetic tape sound recording and reproducing systems.
Part 8: Eight track magnetic tape cartridge for commercial tape
records and domestic use.
(Based on IEC-94-8/1987)

500. PS-3360-9/1996 Magnetic tape sound recording and reproducing systems.

use. Part 9: Magnetic tape cartridge for professional use.
(Based on IEC-94-9/1988)

501. PS-3360-10/1996 Magnetic tape sound recording and reproducing systems.

Part 10: Time and address codes.
(Based on IEC-94-10/1988)

502. PS-3360-11/1997 Magnetic tape sound recording and reproducing systems.

Part 11: Address code for compact cassettes.
(Based on IEC-94-11/1988)

503. PS-3361/1993 Guide to the calculation of resistance of plain and coated

copper conductors of low-frequency cables and wires.
(Based on IEC-344/1980)
 41

504. PS: 3362-1/2002 Low-frequency cables and wires with PVC insulation and PVC
sheath –
Part 1: General testS and measuring methods.
(1st Revision).
(Withdrawn & superseded by PS-3362-1/2014)

PS: 3362-1/2014 Low-frequency cables and wires with PVC insulation and PVC
sheath –
Part 1: General test and measuring methods.
(2nd Revision).
(Based on IEC-60189-1/2007)

505. PS: 3362-2/1994 Low-frequency cables and wires with PVC insulation and PVC
sheath –
Part 2: Cables in pairs, triples, quads and quintuples for inside
installations. (Withdrawn & superseded by PS-3362-2/2014)

PS: 3362-2/2014 Low-frequency cables and wires with PVC insulation and PVC
sheath –
Part 2: Cables in pairs, triples, quads and quintuples for inside
installations. (1st Revision)
(Based on IEC-60189-2/2007)

506. PS: 3362-3/1994 Low-frequency cables and wires with PVC insulation and PVC
sheath –
Part 3: Equipment wires with solid or stranded conductors, PVC
insulated, in singles, pairs and triples.
(Withdrawn & superseded by PS-3362-3/2014)

PS: 3362-3/2014 Low-frequency cables and wires with PVC insulation and PVC
sheath –
Part 3: Equipment wires with solid or stranded conductor wires, PVC
insulated, in singles, pairs and triples. (1st Revision)
(Based on IEC-60189-3/2007)

507. PS-3362-4/1996 Low-frequency cables and wires with p.v c. insulation and
p.v.c. sheath. Part 4: Distribution wires with solid conductors,
P.V.C. insulated, in pairs, triples, quads and quintuples.
(Replaced PS-1182/1974)
(Based on IEC-189-4/1980)

508. PS-3362-5/1996 Low-frequency cables and wires with p.v c. insulation and
p.v.c. sheath. Part 5: Equipment wires and cables with solid or
stranded conductors, p.v.c. insulated, screened, single or one pair.
(Replaced PS-1183/1974)
(Based on IEC-189-5/1980)
 42

509. PS-3363-2/1993 Optical fibre cables.

Part 2: Product specifications.
(Based on IEC-794-2/1989)

510. PS-3363-3/1997 Optical fibre cables-

Part 3: Telecommunication cables-
Sectional specification.
(Based on IEC-794-3/1994)

511. PS-3364/1993 Alpha, beta and alpha-beta contamination meters and monitors.
(Based on IEC-325/1981)

512. PS-3365/1993 Warning equipment for criticality accidents.

(Based on IEC-860/1987)

513. PS-3366-1/1993 Outline dimensions of transformers and inductors for use

in telecommunication and electronic equipment.
Part 1: Transformers and inductors using YEI – 1 laminations.
(Based on IEC-852-1/1986)

514. PS-3540-2/1994 Operating conditions for industrial-process measurement and control

equipment.
Part 2: Power.
(Based on IEC-654-2/1979)

515. PS-3540-3/1996 Operating conditions for industrial-process measurement and

control equipment.
Part 3: Mechanical influences.
(Based on IEC-654-3/1983)

516. PS-3540-4/1994 Operating conditions for industrial-process measurement

and control equipment.
Part 4: Corrosive and erosive influences.
(Based on IEC-654-4/1987)

517. PS-3541-2/1994 Potentiometers for use in electronic equipment-

Part 2: Sectional specification: Lead-screw actuated and rotary preset
potentiometers.
(Replaced PS-2904-2/1990)
(Based on IEC-393-2/1989)

518. PS-3541-3/1994 Potentiometers for use in electronic equipment-

Part 3: Sectional specification: Rotary precision potentiometers.
(Replaced PS-2904-3/1990)
(Based on IEC-393-3/1992)
 43

519. PS-3541-3-1/1994 Potentiometers for use in electronic equipment-

Part 3: Blank detail specification: Rotary precision potentiometers.
Assessment level E.
(Based on IEC-393-3-1/1992)

520. PS-3541-4/1995 Potentiometers for use in electronic equipment.

Part 4: Sectional specification: Single-turn rotary power
potentiometers.
(Replaced PS-2904-4/1990)
(Based on IEC-393-4/1992)

521. PS-3542-0-1/1994 Radio-frequency cables.

Part 0: Guide to the design of detail specification.
Section One: Coaxial cables.
(Based on IEC-96-0-1/1990)

522. PS-3542-2/1998 . Radio-frequency cables-

IEC-96-2/1961 Part 2: Relevant cable specifications.
(Withdrawn)
523. PS-3542-3/1997 Radio-frequency cables.
Part 3: General requirements and tests for single-unit coaxial cables
for use in cabled distribution systems.
(Based on IEC-96-3/1982)

524. PS-3543-1/1998 Quartz crystal controlled oscillators of assessed quality-

IEC-679-1/1997 Part 1: Generic specification.
(Withdrawn)
525. PS-3543-2/1994 Quartz crystal controlled oscillators.
Part 2: Guide to the use of quartz crystal controlled oscillators.
(Based on IEC-679-2/1981)

526. PS-3543-5/2000 Quartz crystal controlled oscillators of assessed quality-

Part-5: Sectional specification- Qualification approval.
(Based on IEC-679-5/1998)

527. PS-3543-5-1/2000 Quartz crystal controlled oscillators of assessed quality-

Part-5-1: Blank detail specification- Qualification approval.
(Based on IEC-679-5-1/1998)

528. PS: 3544-1/1994 Fibre optic switches –

Part 1: Generic specification.
(Withdrawn & superseded by PS-3544-1/2014)

PS: 3544-1/2014 Fibre optic interconnecting devices and passive components –

Fibre optic spatial switches –
 44

Part 1: Generic specification.

(1st Revision)
(Based on IEC-60876-1/2012)

529. PS-3545/1994 Low-energy X or gamma radiation portable exposure rate

meters and monitors for use in radiological protection.
(Based on IEC-463/1974)

530. PS-3546-1/1994 Portable, transportable or installed X or gamma radiation rate meters

for environmental monitoring.
Part 1: Rate meters.
(Based on IEC-1017-1/1991)

531. PS-3547-1/1994 Inductor and transformer cores for telecommunications.

Part 1: Generic specification.
(Based on IEC-723-1/1982)

532. PS-3547-2/1995 Inductor and transformer cores for telecommunications.

Part 2: Sectional specification: Magnetic oxide cores for inductor
applications.
(Based on IEC-723-2/1983)

533. PS-3547-2-1/1995 Inductor and transformer cores for telecommunications.

Part 2: Blank detail specification: Magnetic oxide cores for
inductor applications. Assessment level A.
(Based on IEC-723-2-1/1983)

534. PS-3547-4/1997 Inductor and transformer cores for telecommunications.

Part 4: Sectional specification: Magnetic oxide cores for
transformers and chokes for power applications.
(Based on IEC-723-4/1987)

535. PS-3547-4-1/1997 Inductor and transformer cores for telecommunications.

Part 4: Blank detail specification: Magnetic oxide cores for
transformers and chokes for power applications.
Assessment level A.
(Based on IEC-723-4-1/1987)

536. PS-3548-1/1994 Laminated core packages for transformers and inductors

used in telecommunication and electronic equipment.
Part 1: Dimensions.
(Based on IEC-1021-1/1990)

537. PS-3549/1994 Information processing – ISO 8-bit code for information

interchange- Structure and rules for implementation.
(Based on ISO/IEC-4873/1991)
 45

538. PS-3550-1/1994 Potentiometers for use in electronic equipment.

Part 1: Generic specification.
539. PS-3551-1/1994 Piezoelectric filters. Part 1: General information, standard values and
test conditions.
540. PS-3551-3/1994 Piezoelectric filters. Part 3: Standard outlines.
(Withdrawn)
541. PS-3552-3/1994 Quartz crystal controlled oscillators.
Part 3: Standard outlines and lead connectors.
542. PS-3553/1994 Nuclear instrumentation-
IEC-333/1993 Semiconductor charged-particle detectors- Test procedures.
(Replaced PS-1298/1974)
(Withdrawn)
543. PS-3677/1995 Mechanical structures for electronic equipment.
Terminology.
(Based on IEC-916/1988)
544. PS-3678/1995 PS terminology in the nuclear reactor field.
(Based on IEC-557/1982)
545. PS-3679-1/1995 Standardization of interconnections between broadcasting
transmitters or transmitting systems and supervisory equipment.
Part 1: Interface standards for systems using dedicated
interconnections.
(Based on IEC-864-1/1986)
546. PS-3680-1/1995 Dimensions of mechanical structures of the 482.6 mm (19 in) series.
Part 1: Panels and racks.
(Replaced PS-1264/1974)
(Based on IEC-297-1/1986)
547. PS-3680-2/1995 Dimensions of mechanical structures of the 482.6 mm (19 in) series.
Part 2: Cabinets and pitches of rack structures.
(Replaced PS-1264/1974)
(Based on IEC-297-2/1982)
548. PS-3681-1/1995 Hollow metallic waveguides- Part-1: General requirements and
measuring methods.
(Replaced PS-1146/1974)
(Based on IEC-153-1/1964)
549. PS-3681-2/1995 Hollow metallic waveguides-
Part-2: Relevant specifications for ordinary rectangular waveguides.
(Replaced PS-1147/1974)
(Based on IEC-153-2/1974)
550. PS-3681-3/1996 Hollow metallic waveguides-
Part-3: Relevant specifications for flat rectangular waveguides.
 46

(Replaced PS-1148/1974)
(Based on IEC-153-3/1964)
551. PS-3681-4/1998 Hollow metallic waveguides-
Part 4: Relevant specifications for circular waveguides.
(Replaced PS-1149/1974)
552. PS-3681-6/1998 Hollow metallic waveguides-
IEC-153-6/1967 Part 6: Relevant specifications for medium flat rectangular
waveguides.
(Replaced PS-1151/1974)
(Withdrawn)
553. PS-3681-7/1998 Hollow metallic waveguides-
IEC-153-7/1972 Part 7: Relevant specifications for square waveguides.
(Withdrawn)
554. PS: 3682/1995 Measurements and test methods for 32 kHz quartz crystal units for
wrist watches and standard values.
(Withdrawn & superseded by PS-3682/2014)

PS: 3682/2014 Measurement and test methods for tuning fork quartz crystal units in the
range from 10 kHz to 200 kHz and standard values.
(1st Revision)
(Based on IEC-689/2008)
555. PS-3683-1/1995 Transformers and inductors for use in electronic equipment.
Designations for cores and assemblies.
Part 1: Laminated cores.
(Based on IEC-1186-1/1992)
556. PS-3684/1995 Information technology – software product evaluation –
Quality characteristics and guidelines for their use.
(Based on ISO/IEC-9126/1991)

557. PS-3783-2/1996 Varistors for use in electronic equipment.

Part 2: Sectional specification for surge suppression varistors.
(Based on IEC-1051-2/1991)

558. PS-3783-2-1/1997 Varistors for use in electronic equipment.

Part 2: Blank detail specification for silicon carbide surge suppression
varistors.
Assessment level E.
(Based on IEC-1051-2-1/1991)

559. PS-3784/1996 Modular order for the development of mechanical structures for
electronic equipment practices.
(Based on IEC-917/1988)

560. PS-3785/1996 Piezoelectric ceramic resonators and resonator units for

frequency control and selection. Chapter I: Standard values
and conditions. Chapter II: Measuring and test conditions.
 47

(Based on IEC-642/1979)

561. PS-3785-2/1998 Piezoelectric ceramic resonator units-

IEC-642-2/1994 Part 2: Guide to the use of piezoelectric ceramic resonator units.
(Withdrawn)
562. PS-3785-3/1997 Piezoelectric ceramic resonators-
Part 3: Standard outlines.
(Based on IEC-642-3/1992)

563. PS-3786/1996 Fibre optics – Safety guide.

(Based on IEC-1218/1993)

564. PS-3787/1996 Dimensions of square cores (RM-cores) made of magnetic

oxides and associated parts.
(Based on IEC-431/1983)

565. PS-3788-1/1996 Information processing systems- Fibre Distributed Data

Interface (FDDI) –
Part 1: Token Ring Physical Layer Protocol (PHY).
(Based on ISO-9314-1/1989)

566. PS-3788-2/1999 Information processing systems –

ISO/IEC:9314-2/ 89 Fibre distributed data interface (FDDI) Part-2: Token ring media
access control (MAC).
(Withdrawn)
567. PS-3788-3/1999 Information processing systems – Fibre distributed data interface
ISO/IEC:9314-3/ 90 (FDDI)
Part 3: Physical layer medium dependent (PMD).
(Withdrawn)
568. PS-3789/1996 Fundamental aspects of safety standards for medical electrical
IEC-513/1994 equipment.
(Withdrawn)
569. PS-3790-1/1998 Medical electrical equipment-
IEC-601-1/1988 Part 1: General requirements for safety.
(Withdrawn)
570. PS-3790-1-2/1997 Medical
IE electrical equipment-
Part 1: General requirements for safety- 2 : Collateral standard:
Electromagnetic compatibility-Requirements and tests.
(Based on IEC-601-1-2/1993)

571. PS-3790-1-3/1996 Medical electrical equipment.

IEC-601-1-3/1994 Part 1: General requirements for safety- 3. Collateral standards:
General requirements for radiation protection in diagnostic X-ray
equipment.
(Withdrawn)
572. PS-3790-2-39/2002 Medical electrical equipment-
 48

Part 2-39: Particular requirements for the safety of peritoneal dialysis

equipment.
(Based on IEC-601-2-39/1999)

573. PS-3790-2-45/2000 Medical electrical equipment –

Part-2-45: Particular requirements for the safety of mammographic
X-ray equipment and mammographic stereotactic devices.
(Based on IEC-601-2-45/1998)

574. PS-3790-2-46/2000 Medical electrical equipment-

Part-2-46: Particular requirements for the safety of operating tables.
(Based on IEC-601-2-46/1998)

575. PS-3994/1997 Terminal markings for valve device stacks and assemblies and for
power convertor equipment.
(Based on IEC-1148/1992)

576. PS-3995-1/1997 Packaging of components for automatic handling.

Part 1: Tape packaging of components with axial leads on
continuous tapes.
(Replaced PS-1259/1974)
(Based on IEC-286-1/1997)

577. PS-3995-2/1997 Packaging of electronic components for automatic handling.

Part 2: Specification for tape packaging of components with
unidirectional leads on continuous tapes.
(Replaced PS-1259/1974)
(Based on BS-6062-2/1988)

578. PS-3995-3/1999 Packaging of components for automatic handling –

IEC: 286-3/1997 Part 3: Packaging of leadless components on continuous tapes.
(Withdrawn)
579. PS-3995-4/1999 Packaging of components for automatic handling –
IEC: 286-4/1997 Part 4: Stick magazines for electronic components encapsulated in
packages of form E and G.
(Withdrawn)
580. PS-3995-5/1999 Packaging of components for automatic handling –
IEC: 286-5/1995 Part 5: Matrix trays.
(Withdrawn)
581. PS-3995-6/2000 Packaging of components for automatic handling –
Part 6: Bulk case packaging for surface mounting components.
(Based on IEC-286-6/1998)

582. PS-3996-1/1997 Electromechanical components for electronic equipment-

Basic testing procedures and measuring methods-
Part 1: General.
 49

(Based on IEC-512-1/1994)

583. PS-3996-1-3/1999 Electromechanical components for electronic equipment-

Basic testing procedures and measuring methods –
Part 1: General examination- Section 3: Test 1c - Electrical
engagement length.
(Based on IEC-512-1-3/1997)

584. PS-3996-1-4/1999 Electromechanical components for electronic equipment –

Basic testing procedures and measuring methods-
Part –1: General- Section 4: Test 1d: Contact protection
effectiveness (scoop-proof).
(Based on IEC-512-1-4/1997)

585. PS-3996-6-5/1999 Electromechanical components for electronic equipment.

Basic testing procedures and measuring methods – Part-6: Dynamic
stress tests – Section 5: Test 6 e: Random vibration.
(Based on IEC-512-6-5/1997)

586. PS-3996-7/2000 Electromechanical components for electronic equipment.

Basic testing procedures and measuring methods.
Part 7: Mechanical operating tests and sealing tests.
(Based on IEC-512-7/1993)

587. PS-3997/1997 Sampling rate and source encoding for professional digital audio
recording.
(Based on IEC-899/1987)

588. PS-3998/1997 Copper alloy used for equipment wires.

(Based on IEC-798/1984)

589. PS-3999/1997 Coaxial cable connectors used in nuclear instrumentation.

(Replaced PS-1273/1974)
(Based on IEC-313/1983)

590. PS-4000-1/1997 Semiconductor power convertors- Adjustable speed electrical drive

IEC-1136-1/1992 systems- General requirements-
Part 1: Rating specifications, particularly for d. c. motor drives.
(Withdrawn)
591. PS-4001/1997 Preparation of function charts for control systems.
IEC-848/1988 (Withdrawn)
592. PS-4002/1997 Terminology related to microprocessors.
(Based on IEC-824/1988)

593. PS-4003/1997 Wires for wire wrapping applications.

(Based on IEC-979/1989)
 50

594. PS-4111/1998 Graphical symbols for use on equipment.

IEC-417/1973 Index, survey and compilation of the single sheets.
(Withdrawn)
595. PS-4111-0/1998 Graphical symbols for use on specific equipment.
IEC-417-0/1996 Supplement.
(Withdrawn)
596. PS-4111 L/1998 Graphical symbols for use on specific equipment.
IEC-417 L/1993 Eleventh supplement.
(Withdrawn)
597. PS-4111 M/1998 Graphical symbols for use on specific equipment.
IEC-417 M/1994 Twelfth supplement.
(Withdrawn)
598. PS-4111 N/1998 Graphical symbols for use on specific equipment.
IEC-417 N/1995 Thirteenth supplement.
(Withdrawn)
599. PS-4112-1/1998 Standard data element types with associated classification scheme
IEC-1360-1/1995 for electric components-
Part 1: Definitions-Principles and methods.
(Withdrawn)
600. PS-4112-3/1998 Standard data element types with associated classification scheme
IEC-1360-3/1995 for electric components-
Part 3: Maintenance and validation procedures.
(Withdrawn)
601. PS-4113-1/1998 Methods of measurement for radio transmitters-
IEC-244-1/1968 Part 1: General conditions of measurement, frequency, output power
and power consumption.
(Replaced PS-1225/1974)
(Withdrawn)
602. PS-4113-1A/1998 Methods of measurement for radio transmitters-
IEC-244-1A/1968 Part 1: General conditions of measurement, frequency, output power
and power consumption. First supplement: Appendices.
(Withdrawn)
603. PS-4113-2/1998 Methods of measurement for radio transmitters-
IEC-244-2/1969 Part 2: Bandwidth, out-of-band power and power of non-essential
oscillations.
(Replaced PS-1226/1974)
(Withdrawn)
604. PS-4113-2 A/1998 Methods of measurement for radio transmitters-
IEC-244-2A/1969 Part 2: Bandwidth, out-of-band power and power of non-essential
oscillations.
First supplement: Appendices.
(Withdrawn)
605. PS-4113-2 B/1998 Methods of measurement for radio transmitters-
IEC-244-2B/1969 Part 2: Bandwidth, out-of-band power and power of non-essential
oscillations.
 51

Second supplement: Modulating signals for the measurement of

bandwidth and out-of-band power of transmitters for telephony
and sound broadcasting.
(Withdrawn)
606. PS-4113-3/1998 Methods of measurement for radio transmitters-
IEC-244-3/1972 Part 3: Wanted and unwanted modulation.
(Replaced PS-1227/1974)
(Withdrawn)
607. PS-4113-3A/1998 Methods of measurement for radio transmitters-
IEC-244-3A/1971 Part 3: Wanted and unwanted modulation-
First supplement: Appendices.
(Withdrawn)
608. PS-4113-3B/1998 Methods of measurement for radio transmitters-
IEC-244-3B/1972 Part 3: Wanted and unwanted modulation-
Second supplement: Unwanted modulation, including hum and noise
modulation.
(Withdrawn)
609. PS-4113-4/1998 / Methods of measurement for radio transmitters-
IEC-244-4/1973 Part 4: Amplitude/ frequency characteristics and non-linearity
distortion in transmitters for radiotelephony and sound broadcasting.
(Replaced PS-1228/1974)
(Withdrawn)
610. PS-4113-4A/1998 Methods of measurement for radio transmitters-
IEC-244-4A/1976 Part 4: Amplitude/ frequency characteristics and non-linearity
distortion in transmitters for radiotelephony and sound broadcasting.
First supplement: Section Three.
(Withdrawn)
611. PS-4113-5/1998 Methods of measurement for radio transmitters-
IEC-244-5/1992 Part 5: Performance characteristics of television transmitters.
(Replaced PS-1229/1974)
(Withdrawn)
612. PS-4113-6/1998 Methods of measurement for radio transmitters-
IEC-244-6/1976 Part 6: Cabinet radiation at frequencies between 130 kHz and 1 GHz.
(Withdrawn)
613. PS-4113-7/1998 Methods of measurement for radio transmitters-
IEC-244-7/1979 Part 7: Cabinet radiation at frequencies above 1 GHz.
(Withdrawn)
614. PS-4113-7A/1998 Methods of measurement for radio transmitters-
IEC-244-7A/1980 Part 7: Cabinet radiation at frequencies above 1 GHz.
First supplement: Section Four: Medium-sized transmitters-
Section Five: Large transmitters.
(Withdrawn)
615. PS-4113-8/1998 Methods of measurement for radio transmitters-
IEC-244-8/1993 Part 8: Performance characteristics of vestigial-sideband
demodulators used for testing television transmitters and
transposers.
 52

(Withdrawn)
616. PS-4113-9/1998 Methods of measurement for radio transmitters-
IEC-244-9/1993 Part 9: Performance characteristics for television transposers.
(Withdrawn)
617. PS-4113-10/1998 Methods of measurement for radio transmitters-
IEC-244-10/1986 Part 10: Methods of measurement for television transmitters and
transposers employing insertion test signals.
(Withdrawn)
618. PS-4113-11/1998 Methods of measurement for radio transmitters-
IEC-244-11/1989 Part 11: Transposers for FM sound broadcasting.
(Withdrawn)
619. PS-4113-12-1/1998 Methods of measurement for radio transmitters-
IEC-244-12-1/1989 Part 12: Guideline for drawing up descriptive leaflets for transmitters
and transposers for sound and television broadcasting-
Characteristic to be specified.
(Withdrawn)
620. PS-4113-12-2/1998 Methods of measurement for radio transmitters-
IEC-244-12-2/1989 Part 12: Guideline for drawing up descriptive leaflets for transmitters
and transposers for sound and television broadcasting-
Specification sheets.
(Withdrawn)
621. PS-4113-13/1998 Methods of measurement for radio transmitters-
IEC-244-13/1991 Part 13: Performance characteristics for FM sound broadcasting.
(Withdrawn)
622. PS-4113-14/1999 Methods of measurement for radio transmitters –
Part 14: External intermodulation products, caused by two
or more transmitters using the same or adjacent antennas.
(Based on IEC-244-14/1997)

623. PS-4114-1/1998 Methods of measurement on receivers for satellite broadcast

IEC-1079-1/1992 transmissions in the 12 GHz band- Part 1: Radio-frequency
measurements on outdoor units.
(Withdrawn)
624. PS-4114-2/1998 Methods of measurement on receivers for satellite broadcast
IEC-1079-2/1992 transmissions in the 12 GHz band- Part 2: Electrical measurements
on DBS tuner units.
(Withdrawn)
625. PS-4114-3/1998 Methods of measurement on receivers for satellite broadcast
IEC-1079-3/1993 transmissions in the 12 GHz band- Part 3: Electrical measurements
of overall performance of receiver systems comprising an outdoor
unit and DBS tuner units.
(Withdrawn)
626. PS-4114-4/1998 Methods of measurement on receivers for satellite broadcast
IEC-1079-4/1993 transmissions in the 12 GHz band- Part 4: Electrical measurements
on sound / data decoder units for the digital subcarrier NTSC system.
(Withdrawn)
 53

627. PS-4114-5/1998 Methods of measurement on receivers for satellite broadcast

IEC-1079-5/1993 transmissions in the 12 GHz band- Part 5: Electrical measurements
on decoder units for MAC / packet systems.
(Withdrawn)
628.
349. PS-4115-1/1998 349. Methods of measurement of receiving antennas for satellite
IEC-1114-1/1992 broadcast transmissions in the 12 GHz band – Part 1: Electrical
measurements on DBS receiving antennas.
(Withdrawn)
629. PS-4116-1/1998 Methods of measurement for equipment used in terrestrial radio-
IEC-487-1/1984 relay systems. Part 1: Measurements common to sub-systems and
simulated radio-relay systems.
(Withdrawn)
630. PS-4116-2-1/1998 Methods of measurements for equipment used in terrestrial radio-
IEC-487-2-1/1981 relay systems. Part 2: Measurements for sub-systems.
Section One: General.
(Withdrawn)
631. PS-4116-2-2/1998 Methods of measurements for equipment used in terrestrial radio-
IEC-487-2-2/1981 relay systems. Part 2: Measurements for sub-systems.
Section Two: Stand-by channel switching equipment.
(Withdrawn)
632. PS-4116-2-3/1998 Methods of measurements for equipment used in terrestrial radio-
relay systems. Part 2: Measurements for sub-systems.
Section Three: R.F. Branching networks.
(Withdrawn)
633. PS-4116-2-4/1998 Methods of measurements for equipment used in terrestrial radio-
IEC-487-2-4/1984 relay systems. Part 2: Measurements for sub-systems.
Section Four: Frequency modulators.
(Withdrawn)
634. PS-4116-2-5/1998 Methods of measurements for equipment used in terrestrial radio-
IEC-487-2-5/1984 relay systems. Part 2: Measurements for sub-systems.
Section Five: Frequency demodulators.
(Withdrawn)
635. PS-4116-2-6/1998 Methods of measurements for equipment used in terrestrial radio-
IEC-487-2-6/1984 relay systems. Part 2: Measurements for sub-systems.
Section Six: Diversity, twin-path and hot stand-by equipment.
(Withdrawn)
636. PS-4116-2-7/1998 Methods of measurements for equipment used in terrestrial radio-
IEC-487-2-7/1986 relay systems. Part 2: Measurements for sub-systems.
Section Seven: Radio transmitters.
(Withdrawn)
637. PS-4116-2-8/1998 Methods of measurements for equipment used in terrestrial radio-
IEC-487-2-8/1986 relay systems. Part 2: Measurements for sub-systems.
Section Eight: Radio receivers.
(Withdrawn)
638. PS-4116-3/1998 Methods of measurements for equipment used in terrestrial radio-
IEC-487-3/1975 relay systems. Part 3: Simulated systems.
 54

(Withdrawn)
639. PS-4116-3-2/1998 Methods of measurements for equipment used in terrestrial radio-
IEC-487-3-2/1981 relay systems. Part 3: Simulated systems.
Section Two: Measurements in the baseband.
(Withdrawn)
640. PS-4116-3-3/1998 Methods of measurements for equipment used in terrestrial radio-
IEC-487-3-3/1981 relay systems. Part 3: Simulated systems.
Section Three: Measurements for monochrome and colour television
transmission.
(Withdrawn)
641. PS-4116-3-4/1998 Methods of measurements for equipment used in terrestrial radio-
IEC-487-3-4/1982 relay systems. Part 3: Simulated systems.
Section Four: Measurements for f .d .m transmission.
(Withdrawn)
642. PS-4116-3-5/1998 Methods of measurements for equipment used in terrestrial radio-
IEC-487-3-5/1982 relay systems. Part 3: Simulated systems.
Section Five: Measurement of mutual interference.
(Withdrawn)
643. PS-4116-3-6/1998 Methods of measurements for equipment used in terrestrial radio-
IEC-487-3-6/1984 relay systems. Part 3: Simulated systems.
Section Six: Measurements for sound programme transmission.
(Withdrawn)
644. PS-4117-1-1/1998 Methods of measurement for equipment used in digital microwave
IEC-835-1-1/1990 radio transmission systems.
Part 1: Measurements common to terrestrial radio-relay systems and
satellite earth stations-
Section One: General.
(Withdrawn)
645. PS-4117-1-2/1998 Methods of measurement for equipment used in digital microwave
IEC-835-1-2/1992 radio transmission systems.
Part 1: Measurements common to terrestrial radio-relay systems and
satellite earth stations-
Section 2: Basic characteristics.
(Withdrawn)
646. PS-4117-1-3/1998 Methods of measurement for equipment used in digital microwave
IEC-835-1-3/1992 radio transmission systems.
Part 1: Measurements common toterrestrial radio-relay systems and
satellite earth stations-
Section 3: Transmission characteristics.
(Withdrawn)
647. PS-4117-1-4/1998 Methods of measurement for equipment used in digital microwave
IEC-835-1-4/1992 radio transmission systems.
Part 1: Measurements common to terrestrial radio-relay systems and
satellite earth stations-
Section 4: Transmission performance.
(Withdrawn)
 55

648. PS-4117-2-1/1998 Methods of measurement for equipment used in digital microwave

IEC-835-2-1/1990 radio transmission systems.
Part 2: Measurements on terrestrial radio-relay systems –
Section One: General.
(Withdrawn)
649. PS-4117-2-2/1998 Methods of measurement for equipment used in digital microwave
IEC-835-2-2/1994 radio transmission systems.
Part 2: Measurements on terrestrial radio-relay systems-
Section 2: Antennas.
(Withdrawn)
650. PS-4117-2-3/1998 Methods of measurement for equipment used in digital microwave
IEC-835-2-3/1992 radio transmission systems.
Part 2: Measurements on terrestrial radio-relay systems -
Section 3: R. F. branching networks.
(Withdrawn)
651. PS-4117-2-4/1998 Methods of measurement for equipment used in digital microwave
IEC-835-2-4/1993 radio transmission systems.
Part 2: Measurements on terrestrial radio-relay systems -
Section 4: Transmitter / receiver including modulator / demodulator.
(Withdrawn)
652. PS-4117-2-5/1998 Methods of measurement for equipment used in digital microwave
IEC-835-2-5/1993 radio transmission systems.
Part 2: Measurements on terrestrial radio-relay systems -
Section 5: Digital signal processing sub-systems.
(Withdrawn)
653. PS-4117-2-6/1998 Methods of measurement for equipment used in digital microwave
IEC-835-2-6/1995 radio transmission systems.
Part 2: Measurements on terrestrial radio-relay systems -
Section 6: Protection switching.
(Withdrawn)
654. PS-4117-2-7/1998 Methods of measurement for equipment used in digital microwave
IEC-835-2-7/1994 radio transmission systems.
Part 2: Measurements on terrestrial radio-relay systems -
Section 7: Diversity switching and combining equipment.
(Withdrawn)
655. PS-4117-2-8/1998 Methods of measurement for equipment used in digital microwave
IEC-835-2-8/1993 radio transmission systems.
Part 2: Measurements on terrestrial radio-relay systems -
Section 8: Adaptive equalizer.
(Withdrawn)
656. PS-4117-2-9/1998 Methods of measurement for equipment used in digital microwave
IEC-835-2-9/1995 radio transmission systems.
Part 2: Measurements on terrestrial radio-relay systems -
Section 9: Service channels.
(Withdrawn)
657. PS-4117-2-10/1998 Methods of measurement for equipment used in digital microwave
 56

IEC-835-2-10/1992 radio transmission systems.

Part 2: Measurements on terrestrial radio-relay systems -
Section 10: Overall system performance.
(Withdrawn)
658. PS-4117-2-11/1998 Methods of measurement for equipment used in digital microwave
IEC-835-2-11/1996 radio transmission systems.
Part 2: Measurements on terrestrial radio-relay systems -
Section 11: Cross-polarization interference canceller.
(Withdrawn)
659. PS-4117-3-1/1998 Methods of measurement for equipment used in digital microwave
IEC-835-3-1/1990 radio transmission systems.
Part 3: Measurements on satellite earth stations-
Section 1: General.
(Withdrawn)
660. PS-4117-3-2/1998 Methods of measurement for equipment used in digital microwave
IEC-835-3-2/1995 radio transmission systems.
Part 3: Measurements on satellite earth stations- Section 2: Antennas.
(Withdrawn)
661. PS-4117-3-4/1998 Methods of measurement for equipment used in digital microwave
IEC-835-3-4/1993 radio transmission systems.
Part 3: Measurements on satellite earth stations-
Section 4: Low noise amplifier.
(Withdrawn)
662. PS-4117-3-5/1998 Methods of measurement for equipment used in digital microwave
IEC-835-3-5/1994 radio transmission systems.
Part 3: Measurements on satellite earth stations-
Section 5: Up- and down-convertors.
(Withdrawn)
663. PS-4117-3-6/1998 Methods of measurement for equipment used in digital microwave
IEC-835-3-6/1996 radio transmission systems.
Part 3: Measurements on satellite earth stations-
Section 6: High power amplifiers.
(Withdrawn)
664. PS-4117-3-7/1998 Methods of measurement for equipment used in digital microwave
IEC-835-3-7/1995 radio transmission systems.
Part 3: Measurements on satellite earth stations-
Section 7: Figure-of-merit of receiving system.
(Withdrawn)
665. PS-4117-3-9/1998 Methods of measurement for equipment used in digital microwave
IEC-835-3-9/1993 radio transmission systems.
Part 3: Measurements on satellite earth stations-
Section 9: Terminal equipment- SCPC-PSK.
(Withdrawn)
666. PS-4117-3-10/1998 Methods of measurement for equipment used in digital microwave
IEC-835-3-10/1994 radio transmission systems.
Part 3: Measurements on satellite earth stations-
 57

Section 10: Terminal equipment- TDMA traffic earth station.

(Withdrawn)
667. PS-4117-3-11/1998 Methods of measurement for equipment used in digital microwave
IEC-835-3-11/1995 radio transmission systems.
Part 3: Measurements on satellite earth stations-
Section 11: Service channel equipment for SCPS-PSK transmission.
(Withdrawn)

668. PS-4117-3-12/1998 Methods of measurement for equipment used in digital microwave

IEC-835-3-12/1993 radio transmission systems.
Part 3: Measurements on satellite earth stations-
Section 12: Overall system performance.
(Withdrawn)
669. PS-4117-3-13/1998 Methods of measurement for equipment used in digital microwave
IEC-835-3-13/1996 radio transmission systems.
Part 3: Measurements on satellite earth stations-
Section 13: VSAT systems.
(Withdrawn)
670. PS-4117-3-14/1998 Methods of measurement for equipment used in digital microwave
IEC-835-3-14/1996 radio transmission systems.
Part 3: Measurements on satellite earth stations-
Section 14: Earth stations for satellite news gathering (SNG).
(Withdrawn)
671. PS-4118-1/1998 Cabled distribution systems.
IEC-728-1/1986 Part 1: Systems primarily intended for sound and television signals
operating between 30 MHz and 1 GHz.
(Withdrawn)
672. PS-4118-4/2000 Cabled distribution systems for television and sound signals-
IEC-728-4/1997 Part –4: Passive coaxial wide band distribution equipment.
(Based on IEC-728-4/1997)
(Withdrawn)
673. PS-4119-1/1998 Methods of measurement for radio equipment used in the mobile
IEC-489-1/1983 services.
Part 1: General definitions and standard conditions of measurement.
(Withdrawn)
674. PS-4119-2/1998 Methods of measurement for radio equipment used in the mobile
IEC-489-2/1991 services.
Part 2: Transmitters employing A3E, F3E, or G3E emissions.
(Withdrawn)
675. PS-4119-3/1998 Methods of measurement for radio equipment used in the mobile
IEC-489-3/1988 services.
Part 3: Receivers for A3E or F3E emissions.
(Withdrawn)
676. PS-4119-4/1998 Methods of measurement for radio equipment used in the mobile
IEC-489-4/1991 services.
Part 4: Transmitters employing single-sideband emissions
 58

(R3E, H3E or J3E).

(Withdrawn)
677. PS-4119-5/1998 Methods of measurement for radio equipment used in the mobile
IEC-489-5/1987 services.
Part 5: Receivers employing single-sideband techniques
(R3E, H3E or J3E).
(Withdrawn)
678. PS-4119-6/1998 Methods of measurement for radio equipment used in the mobile
IEC-489-6/1987 services.
Part 6: Selective calling and data equipment.
(Withdrawn)
679. PS-4119-8/1998 Methods of measurement for radio equipment used in the mobile
IEC-489-8/1984 services.
Part 8: Antennas.
(Withdrawn)
680.
354. PS-4120/1998 354. Guide for safe handling and operation of mobile radio equipment.
IEC-1149/1995 (Withdrawn)

681. PS-4121-8/1998 Method for measurement for radio equipment used in the mobile
services. Part 8: Antennas.
(Withdrawn)

682. PS-4122-2/1998 Methods of measurement on receiving antennas for satellite

IEC-1114-2/1996 broadcast transmissions in the 12 GHz band.
Part 2: Mechanical and environmental tests on DBS receiving
antennas.
(Withdrawn)
683. PS-4123-1/1998 Methods of measurement on receivers for television broadcast
IEC-107-1/1997 transmissions.
Part 1: General considerations. Measurements at radio and video
frequencies.
(Replaced PS-1050/1974)
(Withdrawn)
684. PS-4123-2/1998 Methods of measurement on receivers for television broadcast
IEC-107-2/1997 transmissions.
Part 2: Audio channels- General methods and methods for
monophonic channels.
(Replaced PS-1050/1974)
(Withdrawn)
685. PS-4123-3/1998 Recommended methods of measurement on receivers for television
IEC-107-3/1988 broadcast transmissions.
Part 3: Electrical measurements on multichannel sound television
receivers using subcarrier systems.
(Replaced PS-1050/1974)
 59

(Withdrawn)
686. PS-4123-4/1998 Recommended methods of measurement on receivers for television
IEC-107-4/1988 broadcast transmissions.
Part 4: Electrical measurements on multichannel sound television
receivers using the two-carrier FM systems.
(Replaced PS-1050/1974)
(Withdrawn)
687. PS-4123-5/1998 Recommended methods of measurement on receivers for television
IEC-107-5/1992 broadcast transmissions.
Part 5: Electrical measurements on multichannel sound television
receivers using the NICAM two-channel digital sound-systems.
(Replaced PS-1050/1974)
(Withdrawn)
688. PS-4123-6/1998 Recommended methods of measurement on receivers for television
IEC-107-6/1989 broadcast transmissions.
Part 6: Measurement under conditions different from broadcast signal
standards.
(Replaced PS-1050/1974)
(Withdrawn)
689. PS-4124/1998 Informative guide for subjective listening tests.
IEC-543/1976 (Withdrawn)

690. PS-4125/1998 Informative guide for subjective tests on television receivers.

IEC-569/1977 (Withdrawn)

691. PS-4126/1998 Interconnection of radio and T.V receivers to feeder systems outlets.
IEC-1022/1989 (Withdrawn)
692. PS-4127/1998 Recommendations for polycrystalline semiconductor
IEC-119/1960 rectifier stacks and equipment.
(Replaced PS-1076/1974)
(Withdrawn)
693. PS-4128-1/1998 Performance of high-voltage d.c. (HVDC) systems.
IEC-919-1/1988 Part 1: Steady-state conditions.
(Withdrawn)
694. PS-4128-2/1998 Performance of high-voltage d.c. (HVDC) systems.
IEC-919-2/1990 Part 2: Faults and switching.
(Withdrawn)
695. PS-4129/1998 Semiconductor convertors. Identification code for
IEC-971/1989 convertor connections.
(Withdrawn)
696. PS-4130/1998 Low-voltage power supply devices, d.c. output –
IEC-1204/1993 Performance characteristics and safety requirements.
(Withdrawn)
697. PS-4131-3/1998 Adjustable speed electrical power drive systems-
IEC-1800-3/1996 Part 3: EMC - Product standard including specific test methods.
(Withdrawn)
 60

698.
365. PS-4132-2/1998 365. Power convertors for electric traction.
IEC-411-2/1978 Part 2: Additional technical information.
(Withdrawn)
699.
366. PS-4133-1/1998 366. Power convertors installed on board rolling stock-
IEC-1287-1/1995 Part 1: Characteristics and test methods.
(Withdrawn)

700. PS-4134/1998 Methods of evaluating the performance of electrical and

IEC-873/1986 pneumatic analogue chart recorders for use in industrial-
process control systems.
(Replaced PS-2200/1989)
(Withdrawn)
701. PS-4135/1998 Procedures for ensuring the cleanliness of industrial –
IEC-877/1986 process measurement and control equipment in oxygen service.
(Withdrawn)
702. PS-4136/1998 Process data highway, Type C (PROWAYC) for distributed
IEC-955/1989 process control systems.
(Withdrawn)
703. PS-4137-1/1998 Industrial-process control systems- Instruments with analogue
IEC-1003-1/1991 inputs and two- or multi-state outputs-
Part 1: Methods of evaluating the performance.
(Withdrawn)
704. PS-4138/1998 Pneumatic instruments driven by associated process gas –
IEC-1081/1991 Safe installations and operating procedures- Guidelines.
(Withdrawn)
705. PS-4139-1/1998 Programmable measuring instruments- Interface system (byte
IEC-625-1/1993 serial, bit parallel) –
Part 1: Functional, electrical and mechanical specifications, system
applications and requirements for the designer and user.
(Withdrawn)
706. PS-4139-2/1998 Programmable measuring instruments- Interface system (byte
IEC-625-2/1993 serial, bit parallel) –
Part 2: Codes, formats, protocols and common commands.
(Withdrawn)
707. PS-4140-2/1998 Programmable measuring instruments –
Interface system (byte serial, bit parallel).
Part 2: Codes, formats protocols and common commands.
(Withdrawn)
708. PS-4141-1/1998 Electromagnetic compatibility for industrial-process measurement
IEC-801-1/1984 and control equipment.
Part 1: General introduction.
(Withdrawn)
709. PS-4142-1/1998 Industrial-process measurement and control- Evaluation of system
IEC-1069-1/1991 properties for the purpose of system assessment-
Part 1: General considerations and methodology.
(Withdrawn)
 61

710. PS-4142-2/1998 Industrial-process measurement and control- Evaluation of system

IEC-1069-2/1993 properties for the purpose of system assessment-
Part 2: Assessment methodology.
(Withdrawn)
711. PS-4142-3/1998 Industrial-process measurement and control- Evaluation of system
IEC-1069-3/1996 properties for the purpose of system assessment-
Part 3: Assessment of system functionality.
(Withdrawn)
712. PS-4142-5/1998 Industrial-process measurement and control- Evaluation of system
IEC-1069-5/1994 properties for the purpose of system assessment-
Part 5: Assessment of system dependability.
(Withdrawn)
713. PS-4142-6/2000 Industrial –process measurement and control-
IEC-1069-6/1998 Evaluation of system properties for the purpose of system
assessment –
Part-6: Assessment of system operability.
(Based on IEC-1069-6/1998)
(Withdrawn)
714. PS-4143-1/1998 Programmable controllers-
IEC-1131-1/1992 Part 1: General information.
(Withdrawn)
715. PS-4143-2/1998 Programmable controllers-
IEC-1131-2/1992 Part 2: Equipment requirements and tests.
(Withdrawn)
716. PS-4143-3/1998 Programmable controllers-
IEC-1131-3/1993 Part 3: Programming languages.
(Withdrawn)
717. PS-4143-4/1998 Programmable controllers-
IEC-1131-4/1995 Part 4: User guidelines.
(Withdrawn)
718. PS-4144-1/1998 Industrial-process control valves. Part 1: Control valve terminology and
general considerations.
(Withdrawn & superseded by PS-4144-1/2012)

PS-4144-1/2012 Industrial-process control valves -

IEC-534-1/2005 Part 1: Control valve terminology and general considerations.
(1st Revision)
(Based on IEC-534-1/2005)

719. PS-4144-2/1998 Industrial-process control valves.

IEC-534-2/1978 Part 2: Flow capacity:
Section One: Sizing equations for incompressible fluid flow
under installed conditions.
(Withdrawn)
720. PS-4144-2-2/1998 Industrial-process control valves.
IEC-534-2-2/1980 Part 2: Flow capacity:
 62

Section Two: Sizing equations for incompressible fluid flow

under installed conditions.
(Withdrawn)
721. PS-4144-2-3/1998 Industrial-process control valves.
IEC-534-2-3/1997 Part 2: Flow capacity:
Section Three: Test procedures.
(Replaced PS-2197-2-3/1989)
(Withdrawn)
722. PS-4144-2-4/1998 Industrial-process control valves.
IEC-534-2-4/1989 Part 2: Flow capacity:
Section Four: Inherent flow characteristics and rangeability.
(Withdrawn)
723. PS-4144-3/1998 Industrial-process control valves.
IEC-534-3/1976 Part 3: Dimensions-
Section One: Face-to-face dimensions for flanged, two-way,
globe-type control valves.
(Withdrawn)
724. PS-4144-3-2/1998 Industrial-process control valves.
IEC-534-3-2/1984 Part 3: Dimensions-
Section Two: Face-to-face dimensions for flangeless control
valves except water butterfly valves.
(Withdrawn)
725. PS-4144-3-3/2000 Industrial-process control valves –
IEC-534-3-3/1998 Part-3-3: Dimensions- End-to-end dimensions for buttweld, two-
way, globe-type straight pattern control valves.
(Based on IEC-534-3-3/1998)
(Withdrawn)
726. PS-4144-4/1998 Industrial-process control valves.
IEC-534-4/1982 Part 4: Inspection and routine testing.
(Replaced PS-2197-4/1989)
(Withdrawn)
727. PS-4144-5/1998 Industrial-process control valves.
IEC-534-5/1982 Part 5: Marking.
(Withdrawn)
728. PS-4144-6/1998 Industrial-process control valves.
IEC-534-6/1985 Part 6: Mounting details for attachment of positioners to control valve
actuators.
(Withdrawn)
729. PS-4144-6-1/1999 . Industrial – process control valves.
IEC-534-6-1/1997 Part 6: Mounting details for attachments of positioners to control
valves-
Section 1: Positioner mounting on linear actuators.
(Based on IEC-534-6-1/1997)
(Withdrawn)
730. PS-4144-7/1998 Industrial-process control valves.
IEC-534-7/1989 Part 7: Control valve data sheet.
 63

(Withdrawn)
731. PS-4144-8-1/1998 Industrial-process control valves.
IEC-534-8-1/1986 Part 8: Noise considerations-
Section 1: Laboratory measurement of noise generated by
aerodynamic flow through control valves.
(Withdrawn)
732. PS-4144-8-2/1998 Industrial-process control valves.
IEC-534-8-2/1991 Part 8: Noise considerations-
Section 2: Laboratory measurement of noise generated by
hydrodynamic flow through control valves.
(Withdrawn)
733. PS-4144-8-3/1998 Industrial-process control valves.
IEC-534-8-3/1995 Part 8: Noise considerations-
Section 3: Control valves aerodynamic noise prediction method.
(Withdrawn)
734. PS-4144-8-4/1998 Industrial-process control valves.
IEC-534-8-4/1994 Part 8: Noise considerations-
Section 4: Prediction of noise generated by hydrodynamic flow.
(Withdrawn)
735. PS-4145-1/1998 Controllers with analogue signals for use in industrial-process
IEC-546-1/1987 control systems-
Part 1: Methods for evaluating the performance.
(Replaced PS-2198-1/1989)
(Withdrawn)
736. PS-4145-2/1998 Controllers with analogue signals for use in industrial-process
IEC-546-2/1987 control systems-
Part 2: Guidance for inspection and routine testing.
(Withdrawn)
737. PS-4146-1/1998 Thermocouples-
IEC-584-1/1995 Part 1: Reference tables.
(Withdrawn)
738. PS-4146-2/1998 Thermocouples-
IEC-584-2/1982 Part 2: Tolerances.
(Withdrawn)
739. PS-4146-3/1998 Thermocouples-
IEC-584-3/1989 Part 3: Extension and compensating cables.
Tolerances and identification system.
(Withdrawn)
740. PS-4147/1998 Dimensions of metal-sheathed thermometer elements.
IEC-1152/1992 (Withdrawn)
741. PS-4148/1998 Mineral insulated thermocouple cables and thermocouples.
IEC-1515/1995 (Withdrawn)
742. PS-4149-1/1998 Process measurement and control devices- General methods and
IEC-1298-1/1995 procedures for evaluating performance-
Part 1: General considerations.
(Withdrawn)
 64

743. PS-4149-2/1998 Process measurement and control devices- General methods and
IEC-1298-2/1995 procedures for evaluating performance-
Part 2: Tests under reference conditions.
(Withdrawn)
744. PS-4149-4/1998 Process measurement and control devices- General methods and
IEC-1298-4/1995 procedures for evaluating performance-
Part 4: Evaluation report content.
(Withdrawn)
745.
382. PS-4150-2/1998 382. Fieldbus standard for use in industrial control systems-
IEC-1158-2/1993 Part 2: Physical layer specification and service definition.
(Withdrawn)
746. PS-4151/1998 Expressions of performance of air quality infra-red
IEC-528/1975 analyzers.
(Withdrawn)
747. PS-4152/1998 Industrial-process control – Safety of analyzer houses.
IEC-1285/1994 (Withdrawn)
748. PS-4153-1/1998 Expression of performance of electrochemical analyzers-
IEC-746-1/1982 Part 1: General.
(Withdrawn & superseded by PS: IEC 60746-1-2009)
749. PS-4153-2/1998 Expression of performance of electrochemical analyzers-
IEC-746-2/1982 Part 2: pH value.
(Withdrawn & superseded by PS: IEC 60746-2-2009)
750. PS-4153-3/1998 Expression of performance of electrochemical analyzers-
IEC-746-3/1985 Part 3: Electrolytic conductivity.
(Withdrawn)
751. PS-4153-4/1998 Expression of performance of electrochemical analyzers-
IEC-746-4/1992 Part 4: Dissolved oxygen in water measured by membrane covered
amperometric sensors.
(Withdrawn)
752. PS-4153-5/1998 Expression of performance of electrochemical analyzers-
IEC-746-5/1992 Part 5: Oxidation reduction potential or redox potential.
(Withdrawn)
753. PS-4154-1/1998 Expression of performance of gas analyzers-
IEC-1207-1/1994 Part 1: General.
(Withdrawn)
754. PS-4154-2/1998 Expression of performance of gas analyzers-
IEC-1207-2/1994 Part 2: Oxygen in gas (utilizing high-temperature electrochemical
sensors).
(Withdrawn)
755. PS-4154-6/1998 Expression of performance of electrochemical analyzers-
IEC-1207-6/1994 Part 6: Photometric analyzers.
(Withdrawn)
756. PS-4155/1998 Expression of performance of sample handling systems for
IEC-1115/1992 process analyzers.
(Withdrawn)
 65

757. PS-4156-3/1998 Programmable controllers. Part 3: Programming languages.

(Withdrawn)
758. PS-4156-4/1998 Programmable controllers. Part 4: User guidelines.
(Withdrawn)
759. PS-4157/1998 Electrical and pneumatic analogue chart recorders for use
IEC-1153/1992 in industrial – process control systems – Guidance for
inspection and routine testing.
(Withdrawn)
760. PS-4158/1998 Industrial–process control systems- Classification of adoptive
IEC-1297/1995 controllers for the purpose of evaluation.
(Withdrawn)
761. PS-4159/1998 Integrated circuits –
IEC-1739/1996 Part –1: Procedures for manufacturing line approval and quality
management.
(Withdrawn)
762. PS-4160-1/1998 Mechanical standardization of semiconductor devices-
IEC-191-1/1966 Part 1: Preparation of drawings of semiconductor devices-
(Replaced PS-1187/1974)
(Withdrawn)
763. PS-4160-1A/1998 Mechanical standardization of semiconductor devices-
IEC-191-1A/1969 Part 1: Preparation of drawings of semiconductor devices-
First supplement.
(Withdrawn)
764. PS-4160-1B/1998 Mechanical standardization of semiconductor devices-
IEC-191-1B/1970 Part 1: Preparation of drawings of semiconductor devices-
Second supplement.
(Withdrawn)

765. PS-4160-1C/1998 Mechanical standardization of semiconductor devices-

IEC-191-1C/1974 Part 1: Preparation of drawings of semiconductor devices-
Third supplement.
(Withdrawn)
766. PS-4160-2/1998 Mechanical standardization of semiconductor devices-
IEC-191-2/1966 Part 2: Dimensions.
(Replaced PS-1188/1974)
(Withdrawn)
767. PS-4160-2R/1998 Mechanical standardization of semiconductor devices-
IEC-191-2R/1995 Part 2: Dimensions, Sixteenth supplement.
(Withdrawn)
768. PS-4160-2S/1998 Mechanical standardization of semiconductor devices-
IEC-191-2S/1995 Part 2: Dimensions, Seventeenth supplement.
(Withdrawn)
769. PS-4160-2T/1998 Mechanical standardization of semiconductor devices-
IEC-191-2T/1996 Part 2: Dimensions, Eighteenth supplement.
 66

(Withdrawn)
770. PS-4160-3/1998 Mechanical standardization of semiconductor devices-
IEC-191-3/1974 Part 3: General rules for the preparation of outline drawings
of integrated circuits.
(Withdrawn)
771. PS-4160-3A/1998 Mechanical standardization of semiconductor devices-
IEC-191-3A/1976 Part 3: General rules for the preparation of outline drawings
of integrated circuits- First supplement.
(Withdrawn)
772. PS-4160-3B/1998 Mechanical standardization of semiconductor devices-
IEC-191-3B/1978 Part 3: General rules for the preparation of outline drawings
of integrated circuits- Second supplement.
(Withdrawn)
773. PS-4160-3C/1998 Mechanical standardization of semiconductor devices-
IEC-191-3C/1987 Part 3: General rules for the preparation of outline drawings
of integrated circuits- Third supplement.
(Withdrawn)
774. PS-4160-3D/1998 Mechanical standardization of semiconductor devices-
IEC-191-3D/1988 Part 3: General rules for the preparation of outline drawings
of integrated circuits- Fourth supplement.
(Withdrawn)
775. PS-4160-3E/1998 Mechanical standardization of semiconductor devices-
IEC-191-3E/1976 Part 3: General rules for the preparation of outline drawings
of integrated circuits- Fifth supplement.
(Withdrawn)
776. PS-4160-3F/1998 Mechanical standardization of semiconductor devices-
IEC-191-3F/1990 Part 3: General rules for the preparation of outline drawings
of integrated circuits- Sixth supplement.
(Withdrawn)
777. PS-4160-4/1998 Mechanical standardization of semiconductor devices-
IEC-191-4/1987 Part 4: Coding systems and classification into forms of package
outlines for semiconductor devices.
(Withdrawn)
778. PS-4160-5/1998 Mechanical standardization of semiconductor devices-
IEC-191-5/1987 Part 5: Recommendations applying to tape automated bonding
(TAB) of integrated circuits.
(Withdrawn)
779. PS-4160-6/1998 Mechanical standardization of semiconductor devices-
IEC-191-6/1990 Part 6: General rules for the preparation of outline drawings of
surface mounted semiconductor device packages.
(Withdrawn)
780. PS-4161/1998 High-voltage connecting wires with flame retarding insulation for
IEC-197/1965 use in television receivers.
(Replaced PS-1192/1974)
(Withdrawn)
781. PS-4162/1998 Connecting wires having a rated voltage of 20 kV and 25 kV d. c.
 67

IEC-246/1967 and a maximum working temperature of 105 C for use in television

receivers.
(Withdrawn)
782. PS-4163-1/1998 Flanges for waveguides- Part 1: General requirements.
IEC-154-1/1982 (Replaced PS-1152/1974)
(Withdrawn)
783. PS-4163-2/1998 Flanges for waveguides- Part 2: Relevant specification for flanges
IEC-154-2/1980 for ordinary rectangular waveguides. (Replaced PS-1153/1974)
(Withdrawn)
784. PS-4163-3/1998 Flanges for waveguides- Part 3: Relevant specification for flanges
IEC-154-3/1982 for flat rectangular waveguides. (Replaced PS-1154/1974)
(Withdrawn)
785. PS-4163-4/1998 Flanges for waveguides- Part 4: Relevant specification for flanges
IEC-154-4/1969 for circular waveguides. (Replaced PS-1155/1974)
(Withdrawn)
786. PS-4163-6/1998 Flanges for waveguides- Part 6: Relevant specification for flanges
IEC-154-6/1983 for medium flat rectangular waveguides.
(Withdrawn)
787. PS-4163-7/1998 Flanges for waveguides- Part 7: Relevant specification for flanges
IEC-154-7/1974 for square waveguides.
(Withdrawn)
788. PS-4164-2/1998 Flanges for waveguides. Part 2: Relevant specification for flanges for
ordinary rectangular waveguides.
(Replaced PS:1153-1974).
(Withdrawn)
789. PS-4165-2/1998 Radio-frequency cables. Part 2: Relevant cable specifications.
(Withdrawn)
790. PS-4166/1998 Sealing test for pressurized waveguide tubing and assemblies.
IEC-261/1989 (Replaced PS-1238/1974)
(Withdrawn)
791. PS-4167-1/1998 General purpose rigid coaxial transmission lines and their
IEC-339-1/1971 associated flange connectors- Part 1: General requirements and
measuring methods. (Replaced PS-1302/1974)
(Withdrawn)
792. PS-4167-2/1998 General purpose rigid coaxial transmission lines and their
IEC-339-2/1996 associated flange connectors- Part 2: Detail specifications.
(Replaced PS-1303/1974)
(Withdrawn)
793. PS-4168/1998 Guide for choosing modular dimensions for waveguide components.
IEC-374/1971 (Replaced PS-1318/1974)
(Withdrawn)
794. PS-4169/1998 Flexible waveguide assembly performance.
IEC-636/1979 (Withdrawn)
795. PS-4170-1/1998 Radio-frequency and coaxial cable assemblies-
IEC-966-1/1988 Part 1: Generic specification- General requirements and test
 68

methods.
(Withdrawn)
796. PS-4170-2-1/1998 Radio-frequency and coaxial cable assemblies-
IEC-966-2-1/1991 Part 2-1: Sectional specification for flexible coaxial cable assemblies.
(Withdrawn)
797. PS-4170-2-2/1998 Radio-frequency and coaxial cable assemblies-
IEC-966-2-2/1992 Part 2-2: Blank detail specification for flexible coaxial cable
assemblies.
(Withdrawn)
798. PS-4170-2-3/1998 Radio-frequency and coaxial cable assemblies-
IEC-966-2-3/1996 Part 2-3: Detail specification for flexible coaxial cable assembly.
(Withdrawn)
799. PS-4170-2-4/1999 Radio frequency and coaxial cable assemblies.
Part-2-4: Detail specification for cable assemblies for radio and T.V.
receivers (Frequency range 0 to 3000 MHz, IEC- 60169-2
connectors).
(Based on IEC-966-2-4/1997)
800. PS-4170-2-5/2000 Radio frequency and coaxial cable assemblies –
Part- 2-5: Detail specification for cable assemblies for radio and T.V.
receivers – (Frequency range 0 to 1000 MHz, IEC-60169-2
connectors.)
(Based on IEC-966-2-5/1998)
801. PS-4170-2-6/2000 Radio frequency and coaxial cable assemblies –
Part 2-6: Detail specifications for cable assemblies for radio and
T.V. receivers- (Frequency range 0 to 3000 MHz, IEC-60169-24
connectors.)
(Based on IEC-966-2-6/1998)
802. PS-4170-3/1998 Radio-frequency and coaxial cable assemblies-
IEC-966-3/1992 Part 3: Sectional specification for semi-flexible coaxial cable
assemblies.
(Withdrawn)
803. PS-4170-3-1/1998 Radio-frequency and coaxial cable assemblies-
IEC-966-3-1/1992 Part 3-1: Blank detail specification for semi-flexible coaxial cable
assemblies.
(Withdrawn)
804. PS-4170-3-2/1998 Radio-frequency and coaxial cable assemblies-
IEC-966-3-2/1996 Part 3-2: Detail specification for a semi-flexible coaxial cable
assembly for GSM use (0.8 GHz – 1 GHz).
(Withdrawn)
805. PS: 4170-4/2000 Radio-frequency and coaxial cable assemblies –
Part 4: Sectional specification for semi-rigid coaxial cable
assemblies.
(Withdrawn & superseded by PS: 4170-4/2014)

PS: 4170-4/2014 Radio-frequency and coaxial cable assemblies –

Part 4: Sectional specification for semi-rigid coaxial cable
 69

assemblies. (1st Revision).

(Based on IEC-60966-4/2003)

806. PS: 4170-4-1/1998 Radio-frequency and coaxial cable assemblies –

Part 4-1: Blank detail specification for semi-rigid coaxial cable
assemblies.
(Based on IEC-60966-4-1/1998)
(Withdrawn & superseded by PS: 4170-4-1/2014)

PS: 4170-4-1/2014 Radio-frequency and coaxial cable assemblies –

Part 4-1: Blank detail specification for semi-rigid coaxial cable
assemblies. (1st Revision)
(Based on IEC-60966-4-1/2003)

807. PS-4171-1/1998 Radio-frequency cables- Part 1: Generic specification-

IEC-1196-1/1995 General, definitions, requirements and test methods.
(Withdrawn & superseded by PS: 4171-1/2014)

PS: 4171-1/2014 Coaxial communication cables –

Part 1: Generic specification – General, definitions and
requirements. (1st Revision)
(Based on IEC-61196-1/2005)
808. PS-4171-2/1998 Radio-frequency cables- Part 2: Sectional specification for
IEC-1196-2/1995 semi-rigid radio-frequency and coaxial cables with poly-
tetrafluoroethylene (PTFE) insulation.
(Withdrawn)
809. PS-4171-3-1/1998 Radio-frequency cables- Part 3: Coaxial cables for digital
IEC-1196-3-1/1995 communication in horizontal floor wiring- Section 1: Detail
specification for cables of 500 m reach and up to 10 Mb /s.
(Withdrawn)
810. PS: 4171-4/2014 Coaxial communication cables –
Part 4: Sectional specification for radiating cables. (1st Revision)
(Based on IEC-61196-4/2004)
811. PS-4172/1998 Measurement of return loss on waveguide and waveguide
IEC-1580/1995 assemblies.
(Withdrawn)
812. PS-4172-1/1998 Methods of measurement for waveguides- Part 1: Decoupling
IEC-1580-1/1996 and rotation of the plane of polarization.
(Withdrawn)
813. PS-4172-2/1998 Methods of measurement for waveguides- Part 2: Level of
IEC-1580-2/1996 intermodulation products.
(Withdrawn)
814. PS-4172-7/1998 Methods of measurement for waveguides- Part 7: Graphical
IEC-1580-7/1996 method for the determination of waveguide performance.
(Withdrawn)
815. PS-4172-8/1998 Methods of measurement for waveguides- Part 8: Waveguide
 70

IEC-1580-8/1996 power holding capability.

(Withdrawn)
816. PS-4172-9/1998 Methods of measurement for waveguides- Part 9: Reflection
IEC-1580-9/1996 coefficient at rectangular waveguide interfaces.
(Withdrawn)
817. PS-4173/1998 Cable assemblies, cables, connectors and passive microwave
IEC-1726/1995 components-Screening attenuation measurement by the
reverberation chamber method. (Withdrawn)
818. PS-4174-1/1999 Multicore and symmetrical pair/quad cables for digital
IEC-61156-1/94 communications. Part 1: Generic specification.
(Withdrawn)
819. PS-4174-2/1998 Multicore and symmetrical pair/quad cables for digital
IEC-1156-2/1995 communications- Part 2: Horizontal floor wiring- Sectional
specification. (Withdrawn)
820. PS-4174-2-1/1998 Multicore and symmetrical pair/quad cables for digital
IEC-1156-2-1/1995 communications- Part 2: Horizontal floor wiring- Section 1: Blank
detail specification. (Withdrawn)

821. PS-4174-3/1998 Multicore and symmetrical pair/quad cables for digital

IEC-1156-3/1995 communications- Part 3: Work area wiring – Sectional specification.
(Withdrawn)
822. PS-4174-3-1/1998 Multicore and symmetrical pair/quad cables for digital
IEC-1156-3-1/1995 communications- Part 3: Work area wiring- Section 1: Blank
detail specification.
(Withdrawn)
823. PS-4175/1998 Standard colours for insulation for low-frequency cables and wires.
IEC-304/1982 (Replaced PS-1268/1974)
(Withdrawn)
824. PS-4176/1998 Low-frequency miniature equipment wires with solid or stranded
IEC-673/1980 conductor, fluorinated polyhydrocarbon type insulation, single.
(Withdrawn)
825. PS-4177/1998 Aluminium electrical conductor wires used in polyolefin insulated
IEC-753/1982 telecommunication cables.
(Withdrawn)
826. PS-4178-1/1998 Low-frequency cables with polyolefin insulation and moisture
IEC-708-1/1981 barrier polyolefin sheath- Part 1: General design details and
requirements.
(Withdrawn)
827. PS-4178-2/1998 Low-frequency cables with polyolefin insulation and moisture
IEC-708-2/1981 barrier polyolefin sheath- Part 2: Unit type, filled, moisture
barrier polyethylene sheathed cables with copper conductors
and solid or cellular insulation.
(Withdrawn)
828. PS-4178-3/1998 Low-frequency cables with polyolefin insulation and moisture
IEC-708-3/1981 barrier polyolefin sheath- Part 3: Unit type, unfilled, moisture
barrier polyethylene sheathed cables with copper conductors
 71

and solid or cellular insulation.

(Withdrawn)
829. PS-4178-4/1998 Low-frequency cables with polyolefin insulation and moisture
IEC-708-4/1981 barrier polyolefin sheath- Part 4: Unit type, unfilled, moisture
barrier polyolefin sheathed cables with copper conductors,
solid insulation and integral suspension strand.
(Withdrawn)
830. PS-4179/1998 Calculation of maximum overall diameter of cables and
IEC-771/1983 specification of the minimum tensile strength of suspension strand
for low-frequency cables with polyolefin insulation and moisture
barrier polyolefin sheath.
(Withdrawn)
831. PS-4180/1998 PVC insulated ribbon cable with a pitch of 1.27 mm suitable for
IEC-918/1987 insulation displacement terminations.
(Withdrawn)
832. PS-4181-4/1998 Multicore and symmetrical pair/quad cables for digital
IEC-1156-4/1995 communications- Part 4: Riser cables- Sectional specification.
(Withdrawn)
833. PS-4181-4-1/1998 Multicore and symmetrical pair/quad cables for digital
IEC-1156-4-1/1995 communications- Part 4: Riser cables- Section One: Blank detail
specification.
(Withdrawn)
834. PS-4182-1/1998 Radio-frequency connectors- Part 1: General requirements and
IEC-169-1/1987 measuring methods. (Replaced PS-1161/1974)
(Withdrawn)
835. PS-4182-1-1/1998 Radio-frequency connectors- Part 1: General requirements and
IEC-169-1-1/1987 measuring methods- Section One: Electrical test and measuring
procedures: Reflection factor.
(Withdrawn)
836. PS-4182-1-3/1998 Radio-frequency connectors- Part 1: General requirements and
IEC-169-1-3/1988 measuring methods- Section Three: Electrical tests and measuring
procedures. Screening effectiveness.
(Withdrawn)
837. PS-4182-2/1998 Radio-frequency connectors- Part 2: Coaxial unmatched connector.
IEC-169-2/1965 (Replaced PS-1162/1974)
(Withdrawn)
838. PS-4182-3/1998 Radio-frequency connectors- Part 3: Two-pin connector for twin
IEC-169-3/1965 balanced aerial feeders. (Replaced PS-1163/1974)
(Withdrawn)
839. PS-4182-4/1998 Radio-frequency connectors- Part 4: R.F. Coaxial connectors with
IEC-169-4/1975 inner diameter of outer conductor 16 mm (0.63 in) with screw
lock- Characteristic impedance 50 ohms (Type 7-16).
(Replaced PS-1164/1974)
(Withdrawn)
840. PS-4182-5/1998 Radio-frequency connectors- Part 5: R.F. Coaxial connectors for
IEC-169-5/1970 cables 1043, PS: 50-17 and larger. (Replaced PS-1165/1974)
 72

(Withdrawn)
841. PS-4182-6/1998 Radio-frequency connectors- Part 6: R.F. Coaxial connectors
IEC-169-6/1971 for cables 1043, PS: 75-17 and larger. (Replaced PS-1166/1974)
(Withdrawn)
842. PS-4182-7/1998 Radio-frequency connectors- Part 7: R.F. Coaxial connectors with
IEC-169-7/1975 inner diameter of outer conductor 9.5 mm (0.374 in) with bayonet
lock- Characteristic impedance 50 ohms (Type C).
(Withdrawn)
843. PS-4182-8/1998 Radio-frequency connectors- Part 8: R.F. Coaxial connectors with
IEC-169-8/1978 inner diameter of outer conductor 6.5 mm (0.256 in) with bayonet
lock- Characteristic impedance 50 ohms (Type BNC).
(Withdrawn)
844. PS-4182-9/1998 Radio-frequency connectors- Part 9: R.F. Coaxial connectors with
IEC-169-9/1978 inner diameter of outer conductor 3 mm (0.12 in) with screw
coupling- Characteristic impedance 50 ohms (Type SMC).
(Withdrawn)
845. PS-4182-10/1998 Radio-frequency connectors- Part 10: R.F. Coaxial connectors with
IEC-169-10/1983 inner diameter of outer conductor 3 mm (0.12 in) with snap-on
coupling- Characteristic impedance 50 ohms (Type SMB).
(Withdrawn)
846. PS-4182-11/1998 Radio-frequency connectors- Part 11: R.F. Coaxial connectors with
IEC-169-11/1977 inner diameter of outer conductor 9.5 mm (0.374 in) with screw
coupling- Characteristic impedance 50 ohms (Type 4.1/9.5).
(Withdrawn)
847. PS-4182-12/1998 Radio-frequency connectors- Part 12: R.F. Coaxial connectors with
IEC-169-12/1979 screw coupling, unmatched (Type UHF).
(Withdrawn)
848. PS-4182-13/1998 Radio-frequency connectors- Part 13: R.F. Coaxial connectors with
IEC-169-13/1976 inner diameter of outer conductor 5.6 mm (0.22 in)-
Characteristic impedance 75 ohms (Type 1.6/5.6)-
Characteristic impedance 50 ohms (Type 1.8/5.6) with similar
mating dimensions.
(Withdrawn)
849. PS-4182-14/1998 Radio-frequency connectors- Part 14: R.F. Coaxial connectors with
IEC-169-14/1977 inner diameter of outer conductor 12 mm (0.472 in) with screw
coupling- Characteristic impedance 75 ohms (Type 3.5/12).
(Withdrawn)
850. PS-4182-15/1998 Radio-frequency connectors- Part 15: R.F. Coaxial connectors with
IEC-169-15/1979 inner diameter of outer conductor 4.13 mm (0.163 in) with screw
coupling- Characteristic impedance 50 ohms (Type SMA).
(Withdrawn)
851. PS-4182-16/1998 Radio-frequency connectors- Part 16: R.F. Coaxial connectors with
IEC-169-16/1982 inner diameter of outer conductor 7 mm (0.276 in) with screw
coupling- Characteristic impedance 50 ohms (75 ohms) (Type N).
(Withdrawn)
852. PS-4182-17/1998 Radio-frequency connectors- Part 17: R.F. Coaxial connectors with
 73

IEC-169-17/1980 inner diameter of outer conductor 6.5 mm (0.256 in) with screw
coupling- Characteristic impedance 50 ohms (Type TNC).
(Withdrawn)
853. PS-4182-18/1998 Radio-frequency connectors- Part 18: R.F. Coaxial connectors with
IEC-169-18/1985 inner diameter of outer conductor 2.79 mm (0.110 in) screw
coupling- Characteristic impedance 50 ohms (Type SSMA).
(Withdrawn)
854. PS-4182-19/1998 Radio-frequency connectors- Part 19: R.F. Coaxial connectors with
IEC-169-19/1985 inner diameter of outer conductor 2.08 mm (0.082 in) with snap
coupling- Characteristic impedance 50 ohms (Type SSMB).
(Withdrawn)
855. PS-4182-20/1998 Radio-frequency connectors- Part 20: R.F. Coaxial connectors with
IEC-169-20/1985 inner diameter of outer conductor 2.08 mm (0.082 in) screw
coupling- Characteristic impedance 50 ohms (Type SSMC).
(Withdrawn)
856. PS-4182-21/1998 Radio-frequency connectors- Part 21: Two types of radio-
IEC-169-21/1985 frequency connectors with inner diameter of outer conductor
9.5 mm (0.374 in) with different versions of screw coupling-
Characteristic impedance 50 ohms (Type SC-A and SC-B).
(Withdrawn)
857. PS-4182-22/1998 Radio-frequency connectors- Part 22: Two-pole bayonet coupled
IEC-169-22/1985 connectors for use with shielded balanced cables having twin
inner conductors (Type BNO).
(Withdrawn)
858. PS-4182-23/1998 Radio-frequency connectors- Part 23: Pin and socket connector
IEC-169-23/1991 for use with 3.5 mm rigid precision coaxial lines with inner
diameter of outer conductor of 3.5 mm (0.1378 in).
(Withdrawn)
859. PS-4182-24/1998 Radio-frequency connectors- Part 24: R.F. Coaxial connectors with
IEC-169-24/1975 screw coupling, typically for use in 75 ohms cable distribution
system (Type 7-16).
(Withdrawn)
860. PS-4182-25/1998 Radio-frequency connectors- Part 25: Two-pole screw (3/4-20
IEC-169-25/1992 UNEF) coupled connectors for use with shielded balanced cables
having twin conductors with inner diameter of outer conductor
13.56 mm (0.534 in) (Type TWHN).
(Withdrawn)
861. PS-4182-26/1998 Radio-frequency connectors- Part 26: R.F. Coaxial connectors with
IEC-169-26/1993 screw coupling- Characteristic impedance 50 ohms-
Frequency range 0 to 18 GHz (Type TNC 18 GHz)
(Withdrawn)
862. PS-4182-27/1998 Radio-frequency connectors- Part 27: Radio-frequency coaxial
IEC-169-27/1994 connectors with screw coupling, typically for use in 75 ohms
cable distribution systems (Type E).
(Withdrawn)
863. PS-4182-28/1998 Radio-frequency connectors- Part 28: Radio-frequency coaxial
 74

IEC-169-28/1994 connectors with inner diameter of outer conductor of 5.60 mm

(0.220 in) with snap-on coupling - Characteristic impedance 75 ohms.
(Withdrawn)
864. PS-4182-29/1998 Radio-frequency connectors- Part 29: Miniature r. f. coaxial
IEC-169-29/1995 connectors with screw push-pull and snap-on coupling of
slide-in rack and panel applications: Characteristic impedance
50 ohms (Type 1.0 / 2.3).
(Withdrawn)
865. PS-4183-2/1998 General purpose and rigid coaxial transmission lines and their
associated flange connectors. Part 2: Detail specifications.
(Replaced PS-1303/1974). (Withdrawn)
866. PS-4184-1/1998 Rigid precision coaxial and their associated precision connectors.
IEC-457-1/1974 Part 1: General requirements and measuring methods.
(Withdrawn)
867. PS-4184-2/1998 Rigid precision coaxial and their associated precision connectors.
IEC-457-2/1974 Part 2: 50 ohms 7 mm rigid precision coaxial line and associated
hermaphroditic precision coaxial connector.
(Withdrawn)
868. PS-4184-3/1998 Rigid precision coaxial and their associated precision connectors.
IEC-457-3/1980 Part 3: 14 mm rigid precision coaxial line and associated
hermaphroditic precision coaxial connector- Characteristic
impedances 50 ohms and 75 ohms.
(Withdrawn)

869. PS-4184-4/1998 Rigid precision coaxial and their associated precision connectors.
IEC-457-4/1978 Part 4: 21 mm rigid precision coaxial line and associated
hermaphroditic precision coaxial connector- Characteristic
impedance 50 ohms (Type 9 / 21) – Characteristic impedance
75 ohms (Type 6 / 21). (Withdrawn)

870. PS-4184-5/1998 Rigid precision coaxial and their associated precision connectors.
IEC-457-5/1984 Part 5: 50 ohms 3.5 mm rigid precision coaxial line with provision
for mounting connectors. (Withdrawn)

871. PS-4185/1998 Recommended dimensions for hexagonal and square crimping-die

IEC-803/1984 cavities, indentors, gauges, outer conductor crimp sleeves and center
contact crimp barrels for R.F. cables and connectors.
(Withdrawn)
872. PS-4186/1998 Upper frequency limit of r.f. coaxial connectors.
IEC-1141/1992 (Withdrawn)

873. PS-4187-1-1/1998 Radio frequency connectors- Part 1-1: Single multi-series dual
IEC-1169-1-1/1996 language blank detail specification (BDS).
(Withdrawn)
874. PS-4187-33/1998 Radio frequency connectors- Part 33: Sectional specification (SS)
IEC-1169-33/1996 for Type BMA R.F. connectors.
 75

(Withdrawn)
875. PS-4187-36/1998 Radio frequency connectors- Part 36: Micro miniature r. f.
IEC-1169-36/1996 connectors with snap-on coupling- Characteristic impedance
50 ohms (Type MCX).
(Withdrawn)
876. PS-4188-2/1998 Measurement of quartz crystal unit parameters by zero phase
IEC-444-2/1980 technique in a pi-network. Part 2: Phase offset method for
measurement of motional capacitance of quartz crystal units.
(Withdrawn)
877. PS-4188-3/1998 Measurement of quartz crystal unit parameters by zero phase
IEC-444-3/1986 technique in a pi-network. Part 3: Basic method for the
measurement of two-terminal parameters of quartz crystal units
up to 200 MHz by phase technique in a pi-network with
compensation of the parallel capacitance Co.
(Withdrawn)
878. PS-4188-4/1998 Measurement of quartz crystal unit parameters by zero phase
IEC-444-4/1988 technique in a pi-network. Part 4: Method for the measurement
of load resonance frequency f L , load resonance resistance RL
and the calculation of other derived values of quartz crystal units,
up to 30 MHz.
(Withdrawn)
879. PS-4188-6/1998 Measurement of quartz crystal unit parameters-
IEC-444-6/1995 Part 6: Measurement of drive level dependence (DLD).
(Withdrawn)

880. PS-4189-5/1998 Measurement of quartz crystal unit parameters-

BS-7681-5/1995 Part 5: Methods for the determination of equivalent electrical
parameters using automatic network analyzer techniques and
error correction. (Withdrawn)

881. PS-4190/1998 Guide to dynamic measurements of piezoelectric ceramics with high

IEC-483/1976 electromechanical coupling.
(Withdrawn)
882. PS-4191-1-1/1998 Surface acoustic wave (SAW) resonators- Part 1: General
IEC-1019-1-1/1990 information, standard values and test conditions-
Section 1: General information and standard values.
(Withdrawn)
883. PS-4191-1-2/1998 Surface acoustic wave (SAW) resonators- Part 1: General
IEC-1019-1-2/1993 information, standard values and test conditions-
Section 2: Test conditions.
(Withdrawn)
884. PS-4191-2/1998 Surface acoustic wave (SAW) resonators. Part 2: Guide to the use.
(Withdrawn & superseded by PS-4191-2/2012)

PS-4191-2/2012 Surface acoustic wave (saw) resonators –

 76

Part 2: Guide to the use.

(1st Revision)
(Based on IEC-61019-2/2005)

885. PS-4191-3/1998 Surface acoustic wave (SAW) resonators- Part 3: Standard outlines
IEC-1019-3/1991 and lead connections. (Withdrawn)

886. PS-4192/1998 Guide to the measurement of equivalent electrical parameters of

IEC-1080/1991 quartz crystal units.
(Withdrawn)
887. PS-4193/1998 Characteristics and measurements of ultrasonic piezoceramic
IEC-1088/1991 transducers.
(Withdrawn)
888. PS-4194-1/1998 Quartz crystal units- A specification in the IEC Quality
IEC-1178-1/1993 Assessment System for Electronic Components (IECQ)-
Part 1: Generic specification.
(Withdrawn)
889. PS-4194-2/1998 Quartz crystal units- A specification in the IEC Quality
IEC-1178-2/1993 Assessment System for Electronic Components (IECQ)-
Part 2: Sectional specification- Capability approval.
(Withdrawn)
890. PS-4194-2-1/1998 Quartz crystal units- A specification in the IEC Quality
IEC-1178-2-1/1993 Assessment System for Electronic Components (IECQ)-
Part 2: Sectional specification- Capability approval-
Section 1: Blank detail specification.
(Withdrawn)
891. PS-4194-3/1998 Quartz crystal units- A specification in the IEC Quality
IEC-1178-3/1993 Assessment System for Electronic Components (IECQ)-
Part 3: Sectional specification- Qualification approval.
(Withdrawn)
892. PS-4194-3-1/1998 Quartz crystal units- A specification in the IEC Quality
IEC-1178-3-1/1993 Assessment System for Electronic Components (IECQ)-
Part 3: Sectional specification- Qualification approval-
Section 1: Blank detail specification.
(Withdrawn)
893. PS-4195/1998 Piezoelectric devices- Preparation of outline drawings of surface-
IEC-1240/1994 mounted devices (SMD) for frequency control and selection-General
rules.
(Withdrawn)
894. PS-4196-1/1998 Piezoelectric ceramic resonators- A specification in the
IEC-1253-1/1993 IEC Quality Assessment System for Electronic Components
(IECQ)- Part 1: Generic specification- Qualification approval.
(Withdrawn)
895. PS-4196-2/1998 Piezoelectric ceramic resonators- A specification in the
IEC-1253-2/1993 IEC Quality Assessment System for Electronic Components
(IECQ)- Part 2: Sectional specification- Qualification approval.
 77

(Withdrawn)
896. PS-4196-2-1/1998 Piezoelectric ceramic resonators- A specification in the
IEC-1253-2-1/1993 IEC Quality Assessment System for Electronic Components
(IECQ)- Part 2: Sectional specification- Qualification approval.
Section 1: Blank detail specification- Assessment level E.
(Withdrawn)
897. PS-4197-1/1998 Piezoelectric ceramic filters for use in electronic equipment-
IEC-1261-1/1994 A specification in the IEC Quality Assessment System for Electronic
Components (IECQ)- Part 1: Generic specification-
Qualification approval.
(Withdrawn)
898. PS-4197-2/1998 Piezoelectric ceramic filters for use in electronic equipment-
IEC-1261-2/1994 A specification in the IEC Quality Assessment System for Electronic
Components (IECQ)- Part 2: Sectional specification-
Qualification approval.
(Withdrawn)
899. PS-4197-2-1/1998 Piezoelectric ceramic filters for use in electronic equipment-
IEC-1261-2-1/1994 A specification in the IEC Quality Assessment System for
Electronic Components (IECQ) – Part 2: Sectional specification-
Qualification approval- Section 1: Blank detail specification-
Assessment level E.
(Withdrawn)
900. PS-4198-1/2012 Filters using waveguide type dielectric resonators –
Part 1: Generic specification.
(Based on IEC-61337-1/2004)
901. PS-4198-1-1/1998 Filters using waveguide type dielectric resonators- Part 1: General
IEC-1337-1-1/1995 information, standard values and test conditions-
Section 1: General information and standard values.
(Withdrawn)
902. PS-4198-1-2/2001 Filters using waveguide type dielectric resonators-
Part 1-2: Test conditions.
(Based on IEC-61337-1-2/1999)
903. PS-4198-2/2012 Filters using waveguide type dielectric resonators –
Part 2: Guidance for use.
(Based on IEC-61337-2/2004)
904. PS-4199/1998 Methods for the measurement of frequency and equivalent resistance
IEC-283/1968 of unwanted resonances of filter crystal units.
(Replaced PS-1255/1974)
(Withdrawn)
905. PS-4200-3/1998 Surface acoustic wave (SAW) filters-
IEC-862-3/1986 Part 3: Standard outlines (Chapter IV).
(Withdrawn)
906. PS-4201-1-1/1998 Waveguide type dielectric resonators- Part 1: General information
IEC-1338-1-1/1996 and test conditions- Section 1: General information.
(Withdrawn)
907. PS- 4202/1998 Calibration of fibre – optic power meters.
 78

IEC-1315/1995 (Withdrawn & superseded by PS- 4202/2013)

PS- 4202/2013 Calibration of fibre – optic power meters. (1st Revision)

(Based on IEC-61315/2005)
908. PS-4203-2/1998 Connectors for optical fibres and cables- Part 2: Sectional
IEC-874-2/1993 specification for fibre optic connector-Type F- SMA.
(Withdrawn)
909. PS-4203-3/1998 Connectors for optical fibres and cables- Part 3: Sectional
IEC-874-3/1993 specification for fibre optic connector-Type CF03.
(Withdrawn)
910. PS-4203-4/1998 Connectors for optical fibres and cables- Part 4: Sectional
IEC-874-4/1993 specification for fibre optic connector-Type CF04.
(Withdrawn)
911. PS-4203-14-1/1999 Connectors for optical fibre and cables – Part-14-1:
Detail specifications for fibre optic connector type SC/PC standard
terminated to multimode fibre A 1 a, A1 b.
(Based on IEC-874-14-1/1997)

912. PS-4204-1/1998 432. Splices for optical fibres and cables- Part 1: Generic specification-
IEC-1073-1/1994 Hardware and accessories.
(Withdrawn)
913. PS-4205-1/1998 433. Fibre optic isolators- Part 1: Generic specification.
IEC-1202-1/1994 (Withdrawn)
914. PS- 4206-1/1998 Fibre optic adaptors - Generic specification.
IEC-1274-1/1995 (Withdrawn & superseded by PS-4206-1/2013)

PS- 4206-1/2013 Fibre optic interconnecting devices and passive components –

Adaptors for fibre optic connectors – Part 1: Generic specification.
(1st Revision)
(Based on IEC-61274-1/2011)

915. PS-4206-1-1/2013 Fibre optic interconnecting devices and passive components –

Adaptors for fibre optic connectors –
Part 1-1: Blank detail specification
(Based on IEC-61274-1-1/2011)
916. PS-4207-1/1998 Fibre optic interconnecting devices and passive components-
IEC-61300-1/1995 Basic test and measurement procedures- Part 1: General and guidance.
(Withdrawn)
917. PS-4207-2-1/1998 Fibre optic interconnecting devices and passive components-
IEC-61300-2-1/1995 Basic test and measurement procedures- Part 2-1: Tests- Vibration
(sinusoidal).
(Withdrawn & superseded by PS-4207-2-1/2001)

PS-4207-2-1/2001 Fibre optic interconnecting devices and passive components-

Basic test and measurement procedures- Part 2-1: Tests- Vibration
(sinusoidal).
 79

918. PS-4207-2-2/2001 Fibre optic interconnecting devices and passive components- Basic
test and measurement procedures- Part 2-2: Tests- Mating durability.
(Based on IEC-61300-2-2/1995)

919. PS-4207-2-3/2001 Fibre optic interconnecting devices and passive components- Basic
test and measurement procedures- Part 2-3: Tests- Static shear load.
(Based on IEC-61300-2-3/1995)

920. PS-4207-2-4/2001 Fibre optic interconnecting devices and passive components- Basic
test and measurement procedures- Part 2-4: Tests- Fibre / cable
retention.
(Based on IEC-61300-2-4/1995)

921. PS-4207-2-5/2001 Fibre optic interconnecting devices and passive components- Basic
test and measurement procedures-
Part 2-5: Tests- Torsion / twist.
(Based on IEC-61300-2-5/1995)

922. PS-4207-2-41/2000 Fibre optic interconnecting devices and passive components-

Basic test and measurement procedures-
Part-2-41: Tests – Screen testing of attenuation of single mode
tuned non-angled optical fibre connectors.
(Based on IEC-61300-2-41/1998)

923. PS-4207-2-42/2000 Fibre optic interconnecting devices and passive components-Basic

test and measurement procedures –
Part 2-42: Tests-Static side load for connectors.
(Based on IEC-61300-2-42/1998)

924. PS-4208-1/1998 436. Fibre optic passive components and cable assemblies-
IEC-1313-1/1995 Part 1: Capability approval- Generic specification.
(Withdrawn)
925. PS-4209-1/1998 437. Fibre optic fan-outs- Part 1: Generic specification.
IEC-1314-1/1995 (Withdrawn)
926. PS-4210-1/1998 Fibre optic connector interfaces- Part 1: General and guidance.
IEC-1754-1/1996 (Withdrawn)

927. PS-4210-2/1998 Fibre optic connector interfaces- Part 2: Type BFOC/2,5 connector
IEC-1754-2/1996 Family. (Withdrawn)
928. PS-4210-3/1998 Fibre optic connector interfaces- Part 3: Type LSA connector family.
IEC-1754-3/1996 (Withdrawn)
929. PS-4210-4/1999 Fibre optic connector interfaces – Part-4: Type SC connector family.
(Based on IEC-1754-4/1997)

930. PS-4210-5/1998 Fibre optic connector interfaces- Part 5: Type MT connector family.
 80

IEC-1754-5/1996 (Withdrawn)

931. PS-4210-7/1998 Fibre optic connector interfaces- Part 7: Type MPO connector
IEC-1754-7/1996 family. (Withdrawn)

932. PS-4210-8/1998 Fibre optic connector interfaces- Part 8: Type CF08 connector
IEC-1754-8/1996 family. (Withdrawn)

933. PS-4210-9/1998 Fibre optic connector interfaces- Part 9: Type DS connector family.
IEC-1754-9/1996 (Withdrawn)

934. PS- 4210-10/2013 Fibre optic connector interfaces –

Part 10: Type Mini-MPO connector family.

935. PS-4211/1998 Dimensions of planchets used in nuclear electronic instruments.

IEC-248/1984 (Withdrawn)
936. PS-4212/1998 External diameters of cylindrical radiation probes containing.
IEC-256/1967 Geiger-Muller or proportional counter tubes or scintillation
detectors.
(Withdrawn)
937. PS-4213/1998 Dimensions of electronic instruments modules (for nuclear electronic
IEC-482/1975 instruments).
(Withdrawn)
938. PS-4214/1998 High-voltage coaxial connectors used in nuclear instrumentation.
IEC-498/1975 (Withdrawn)
939. PS-4215/1998 A modular instrumentation system for data handling, CAMAC
IEC-516/1975 system.
(Withdrawn)
940. PS-4216/1998 CAMAC-Organization of multi-crate systems.
IEC-552/1977 Specification of the Branch – highway and CAMAC crate controller
type A1. (Withdrawn)
941. PS-4217/1998 CAMAC-Serial Highway Interface System.
IEC-640/1979 (Withdrawn)
942. PS-4218/1998 Block transfers in CAMAC systems.
IEC-677/1980 (Withdrawn)
943. PS-4219/1998 Definitions of CAMAC terms used in Pakistan Standards.
IEC-678/1980 (Withdrawn)
944. PS-4220/1998 Subroutines for CAMAC.
IEC-713/1981 (Withdrawn)
945. PS-4221/1998 Portable bore-hole logging equipment,(down to 300 m)-
IEC-576/1977 General characteristics.
(Withdrawn)
946. PS-4222/1998 Dimensions of vials for liquid scintillation counting.
IEC-582/1977 (Withdrawn)
947. PS-4223/1998 Analogue counting ratemeters. Characteristics and test methods.
IEC-650/1979 (Withdrawn)
 81

948. PS-4224/1998 Equipment for minehead assay and sorting radioactive ores in
IEC-600/1979 containers. (Withdrawn)
949. PS-4225/1998 Density meters utilizing ionizing radiation. Definitions and test
IEC-692/1980 methods. (Withdrawn)
950. PS-4226/1998 Standard test procedures for semiconductor X-ray energy
IEC-759/1983 spectrometers. (Withdrawn)
951. PS-4227/1998 Multiple controllers in a CAMAC crate.
IEC-729/1982 (Withdrawn)
952. PS-4228/1998 Multichannel amplitude analyzers. Standards for time-to-
IEC-741/1982 amplitude converters. (Withdrawn)
953. PS-4229/1998 Guidelines for the development and use of medical electrical
IEC-1258/1994 equipment educational materials.
(Withdrawn)
954. PS-4230/1998 Medical radiology – Terminology.
IEC-788/1984 (Withdrawn)
955. PS-4231/1998 Determination of the maximum symmetrical radiation field from a
IEC-806/1984 rotating anode X-ray tube for medical diagnosis.
(Withdrawn)
956. PS-4232-1/1998 Evaluation and routine testing in medical imaging departments-
IEC-1223-1/1993 Part 1: General aspects. (Withdrawn)

957. PS-4233/1998 Graphical symbols for electrical equipment in medical practice.

IEC-878/1988 (Withdrawn & superseded by PS: IEC 878-2009)

958. PS-4234/1998 Guidelines for administrative, medical, and nursing staff concerned
IEC-930/1988 with the safe use of medical electrical equipment.
(Withdrawn & superseded by PS-4234/2014)

PS-4234/2014 Guidelines for administrative, medical, and nursing staff

concerned with the safe use of medical electrical equipment and
medical electrical systems.
(1st Revision)
(Based on IEC TR 60930/2008)

959. PS-4235-1/1998 Cardiac defibrillators- Cardiac defibrillator-monitors-

IEC-1288-1/1993 Part 1: Operation.
(Withdrawn)
960. PS-4236/1998 X-ray tube assemblies for medical diagnosis – Characteristics of
IEC-336/1993 focal spots.
(Withdrawn & superseded by PS: IEC 60336-2009)
961. PS-4237/1998 Cassettes for medical X-ray diagnosis-Radiographic cassettes and
IEC-406/1997 mammographic cassettes.
(Withdrawn)
962. PS-4238/1998 Inherent filtration of an X-ray tube assembly.
IEC-522/1976 (Withdrawn)
963. PS-4239-1/1998 High frequency surgical equipment- Part 1: Operation.
 82

IEC-1289-1/1994 (Withdrawn)

964. PS-4240/1998 High-voltage cable plug and socket connections for medical X-ray
IEC-526/1978 equipment.
(Withdrawn)
965. PS-4241/1998 Electrical, thermal and loading characteristics of rotating anode
IEC-613/1989 X-ray tubes for medical diagnosis.
(Withdrawn)
966. PS-4242/1998 Characteristics of anti –scatter grids used in X-ray equipment.
IEC-627/1978 (Withdrawn)
967. PS-4243/1998 Radiographic intensifying screens for medical use - Dimensions.
IEC-658/1979 (Withdrawn)
968. PS-4244/1998 Medical electrical equipment – Dosimeters with ionization chambers
IEC-731/1997 as used in radiotherapy.
(Withdrawn)
969. PS-4245-1/1998 Medical electrical equipment- Characteristics of electro-optical
IEC-1262-1/1994 X-ray image intensifiers- Part 1: Determination of the entrance of
field size.
(Withdrawn)
970. PS-4246/1998 Medical diagnostic X-ray equipment – Radiation conditions for use
IEC-1267/1994 in the determination of characteristics.
(Withdrawn & superseded by PS: IEC 61267-2009)

971. PS-4247-1/1998 Protective devices against diagnostic medical X-radiation-

IEC-1331-1/1994 Part 1: Determination of attenuation properties of materials.
(Withdrawn)
972. PS-4247-2/2002 Protective devices against diagnostic medical X– radiation.
Part 2: Protective glass plates.
(Based on IEC-1331-2/1994)

973. PS-4247-3/2002 Protective devices against diagnostic medical X– radiation.

Part 3: Protective clothing and protective devices for gonads.
(Based on IEC-1331-3/1998)

974. PS-4271/1998 Aluminum alloy electrical conductor wires used in polyolefin

IEC-762/1983 insulated telecommunication cables.
(Withdrawn)
975. PS-4272/1998 Dimensions of test tubes made of glass or plastics for radioactivity
IEC-583/1977 measurements.
(Withdrawn)
976. PS-4462/1999 Industrial systems, installations and equipment and industrial
products – Identification of terminals within a system.
(Withdrawn & superseded by PS-4462/2012)

PS-4462/2012 Industrial systems, installations and equipment and industrial

products – Identification of terminals within a system. (1st Revision)
 83

(Based on IEC-61666/2010)

977. PS-4463-2/1999 Standardization of interconnections between broadcasting

transmitters or transmitter systems and supervisory equipment.
Part 2: Interface standards for systems using data bus type
interconnections.
(Based on IEC-864-2/1997)

978. PS-4464/1999 Binary direct voltage signals for process measurement and control
systems
(Based on IEC-946/1988)

979. PS-4465-2/1999 Auxiliary printed board information. Part 2: Rework, repair,

modifications.
(Based on IEC-321-2/1987)

980. PS-4466/1999 Audio recording – PCM encoder / decoder system.

(Based on IEC-841/1988)

981. PS-4467-2/1999 Interconnections of satellite receiving equipment.

Part – 2: Japan.
(Based on IEC-1319-2/1997)

982. PS-4468-2/1999 Household high-fidelity audio equipment and systems –

Methods of measuring and specifying the performance –
Part –2: FM radio tuners.
(Based on IEC-1305-2/1997)

983. PS-4469/1999 Guidelines for radiotherapy treatment rooms design.

(Based on IEC/TR 3: 61859/1997)

984. PS-4470-1/1999 Surface acoustic wave (SAW) filters.

IEC:60862-1/89 Part- 1: General information, standard values and test conditions.
Chapter I: General information and standard values – Chapter II:
Test conditions.
(Withdrawn)
985. PS-4470-2/1999 Surface acoustic wave (SAW) filters.
IEC:60862-2/91 Part 2: Guide to the use of surface acoustic wave filters.
(Chapter – III).
(Withdrawn)
986. PS-4471-1/1999 Fibre optic attenuators – Part 1: Generic specification.
IEC: 60869-1/94 (Withdrawn)
987. PS-4472/1999 Direct current amplifiers; characteristics and test methods.
IEC-527/1975 (Withdrawn)
988. PS-4473/1999 Digital counting ratemeters – Characteristics and test methods.
IEC-739/1983 (Withdrawn)
 84

989. PS-4474-3/1999 Auxiliary printed board information.

IEC: 321-3/90 Part-3: Guidelines for artwork.
(Replaced PS-1292/1974)
(Withdrawn)
990. PS-4475-1/ 1999 Printed boards – Electronic data description and transfer-
IEC: 1182-1/94 Part 1: Printed board description in digital form.
(Withdrawn)
991. PS-4475-7/ 1999 Printed boards – Electronic data description and transfer-
IEC: 1182-7/95 Part 7: Bare board electrical test information in digital form.
(Withdrawn)
992. PS-4476-5-1/1999 Materials for interconnection structures –
IEC: 1249-5-1/95 Part 5: Sectional specification set for conductive foils and films
with and without coatings- Section 1: Copper foils (for the
manufacture of copper-clad base materials).
(Withdrawn)
993. PS-4476-5-4 / 1999 Materials for interconnection structures-
IEC:1249-5-4/96 Part 5: Sectional specification set for conductive foils and films
with or without coatings – Section- 4: Conductive inks.
(Withdrawn)
994. PS-4476-7-1 / 1999 Materials for interconnection structures-Part 7: Sectional
IEC:1249-7-1/95 specification set for restraining core-materials.
Section 1: Copper/invar/copper.
(Withdrawn)
995. PS-4476-8-7 / 1999 Materials for interconnection structures-Part 8: Sectional
IEC:1249-8-7/96 specification set for non-conductive films and coatings.
Section 7: Making legend inks.
(Withdrawn)
996. PS-4477-1 / 1999 Printed boards. Part 1: Generic specification.
IEC:2326-1/96 (Withdrawn)

997. PS-4477-4 / 1999 Printed boards. Part 4: Rigid multilayer printed boards with
IEC:2326-4/96 interlayer connections – Sectional specification.
(Withdrawn)
998. PS-4477-4-1/1999 Printed boards. Part 4: Rigid multilayer printed boards with
IEC:2326-4-1/96 interlayer connections. Sectional specification.
Section 1: Capability detail specification:
Performance level A, B and C.
(Withdrawn)
999. PS-4478/1999 Information processing- Implementation of the 7-bit coded
ISO/IEC-962/1974 character set and its 7-bit and 8-bit extensions on 9-track 12.7 mm
(0.5 in) magnetic tape.
(Withdrawn)
1000. PS-4479/1999 Information processing- File structure and etalize of magnetic
ISO/IEC-1001/1986 tapes for information interchange.
(Withdrawn)
 85

1001. PS-4480/1999 Information processing – Magnetic ink character recognition –

ISO/IEC-1004/1977 Print specifications.
(Withdrawn)
1002. PS-4481-1 / 1999 Alphanumeric character sets for optical recognition-
ISO/IEC:1073-1/76 Part 1:Character set OCR-A-Shapes and dimensions of the printed
image.
(Withdrawn)
1003. PS-4482/1999 Information processing – Representation of the 7-bit coded character
ISO/IEC-1113/1979 set on punched tape.
(Withdrawn)
1004. PS-4483/1999 Information processing – Punched paper tape – Dimensions and
ISO/IEC-1154/1975 location of feed holes and code holes.
(Withdrawn)
1005. PS-4484/1999 Information processing – Use of longitudinal parity to detect errors
ISO/IEC-1155/1978 in information messages.
(Withdrawn)
1006. PS-4485/1999 Information processing – Character structure for start / stop and
ISO/IEC-1177/1985 synchronous character oriented transmission.
(Withdrawn)
1007. PS-4486/1999 Information processing – Unpunched paper cards – Specification.
ISO/IEC-1681/1973 (Withdrawn)

1008. PS-4487/1999 Information processing -80-columns punched paper cards –

ISO/IEC-1682/1973 Dimensions and location of rectangular punched holes.
(Withdrawn)
1009. PS-4488/1999 Information processing – Basic mode control procedures for data
ISO/IEC-1745/1975 communication systems.
(Withdrawn)
1010. PS-4489/1999 Printing specifications for optical character recognition.
ISO/IEC-1831/1980 (Withdrawn)

1011. PS-4490/1999 Information processing – General purpose hubs and reels, with 76
ISO/IEC-1853/1977 mm (3 in) center hole, for magnetic tape used in interchange
instrumentation applications.
(Withdrawn)
1012. PS-4491/1999 Information processing – Precision reels for magnetic tape used in
ISO/IEC-1860/1986 interchange instrumentation applications.
(Withdrawn)
1013. PS-4492/1999 Information processing – 7 – track, 12.7 mm (0.5 in) wide magnetic
ISO/IEC-1861/1975 tape for information interchange recorded at 8 rpmm (200 rpi).
(Withdrawn)
1014. PS- 4493/1999 Directly heated negative temperature coefficient thermistors –
(Withdrawn & superseded by PS-4493-1/2013)

PS- 4493-1/2013 Directly heated negative temperature coefficient thermistors –

Part 1: Generic specification.
 86

(Based on IEC-60539-1/2008)

1015. PS-4494/1999 Indirectly heated thermistors with negative temperature coefficient

IEC-696/1981 (NTC-I).
(Withdrawn)
1016. PS-4495-1 / 1999 Fixed film resistor networks for use in electronic equipment.
IEC:1045-1/91 Part 1: Generic specification.
(Withdrawn)
1017. PS-4496-2 / 1999 Fixed capacitors for use in electronic equipment.
IEC:384-2/82 Part 2: Sectional specification. Fixed metalized polyethylene-
terepthalate film dielectric d.c. capacitors.
(Withdrawn)
1018. PS-4496-3 / 1999 Fixed capacitors for use in electronic equipment.
IEC:384-3/89 Part 3: Sectional specification, fixed tantalum chip capacitors.
(Withdrawn)
1019. PS-4496-5/1999 Fixed capacitors for use in electronic equipment –
IEC:384-5/93 Part 5: Sectional specification: Fixed mica dielectric d.c. capacitors
with a rated voltage not exceeding 3000 V –
Selection of methods of test and general requirements.
(Replaced PS-1057/1974)
(Withdrawn)
1020. PS-4496-6 / 1999 Fixed capacitors for use in electronic equipment.
IEC:384-6/87 Part 6: Sectional specification: Fixed etalized polycarbonate film
dielectric d.c. capacitors.
(Withdrawn)
1021. PS-4496-7 /1999 Fixed capacitors for use in electronic equipment.
IEC:384-7/1991 Part 7: Sectional specification: Fixed polystyrene film dielectric
metal foil d.c. capacitors. (Replaced PS-1253/1974)
(Withdrawn)
1022. PS-4496-8
. /1999 Fixed capacitors for use in electronic equipment.
IEC:384-8/1988 Part 8: Sectional specification: Fixed capacitors of ceramic
dielectric, Class 1. (Replaced PS-1051/1974)
(Withdrawn)
1023. PS-4497/1999 Guide to the use of variable capacitors in electronic equipment.
IEC-612/1978 (Withdrawn)
1024. PS-4498/1999 Capacitors and resistors for electronic equipment. Preferred
IEC-915/1987 dimensions of spindle ends, bushes and for the mounting of single-
hole, bush –mounted, spindle – operated electronic components.
(Withdrawn)
1025. PS-4499-1 / 1999 Fixed inductors for radio interference suppression.
IEC:938-1/88 Part 1: Generic specification.
(Withdrawn)
1026. PS-4500-1 / 1999 Complete filter units for radio interference suppression.
IEC:939-1/88 Part 1: Generic specification.
(Withdrawn)
 87

1027. PS-4501/1999 Guidance information on the application of capacitors, resistors,

IEC-940/1988 inductors and complete filter units for radio interference
suppression.
(Withdrawn)
1028. PS-4502/1999 Analogue audio disk records and reproducing equipment.
IEC-98/1987 (Replaced PS-1044/1974)
(Withdrawn)
1029. PS-4503/1999 Method of measurement of speed fluctuations in sound recording
IEC-386/1972 and reproducing equipment.
(Withdrawn)
1030. PS-4504/1999 Transverse track recorders
IEC-347/1982 (Replaced PS-1307/1974)
(Withdrawn)
1031. PS-4505/1999 Time and control code for video tape recorders.
IEC-461/1986 (Withdrawn)

1032. PS-4506/1999 Type C helical video tape recorders.

IEC-558/1982 (Withdrawn)
1033. PS-4507/1999 Type B helical video recorders.
IEC-602/1980 (Withdrawn)
1034. PS-4508/1999 Helical-scan video-tape cassette system using 19 mm (3/4 in)
IEC-712/1993 magnetic tape, known as U-format.
(Withdrawn)
1035. PS-4509/1999 Measuring methods for video tape properties.
IEC-735/1991 (Withdrawn)
1036. PS-4510/1999 Non-broadcast video tape recorders-Time base stability.
IEC-756/1991 (Withdrawn)
1037. PS-4511/1999 Helical –scan video tape cassette system using 12.65 mm (0.5 in)
IEC-767/1983 magnetic tape on type-beta format.
(Withdrawn)
1038. PS-4512-1 / 1999 Helical-scan video tape cassette system using 12.65 mm (0.5 in)
IEC:774-1/94 magnetic tape on type VHS. Part 1: VHS and compact VHS video
cassette system.
(Withdrawn)
1039. PS-4513-1 /1999 Helical-scan video tape cassette system using 8mm magnetic tape –
IEC:843-1/93 8mm video –Part 1: General specifications.
(Withdrawn)
1040. PS-4513-2/2002 Helical-scan video tape cassette system using 8 mm magnetic tape-
Part 2: PCM multi-track audio system.
(Based on IEC-843-2/1992)
1041. PS-4513-3/2002 Helical-scan video tape cassette system using 8 mm magnetic tape-
Part 3: High-band specifications for Hi 8.
(Based on IEC-843-3/1993)

1042. PS-4514/1999 Pre-recorded optical reflective videodisk system ‘Laser vision’

IEC-856/1986 50 Hz /625 lines PAL.
 88

(Withdrawn)
1043. PS-4515/1999 Pre-recorded optical reflective videodisk system ‘Laser vision’
IEC-857/1986 60 Hz /525 lines – M / NTSC.
(Withdrawn)
1044. PS-4516/1999 Measuring method for chrominance signal –to-random noise ratio
IEC-883/1987 for video tape recorders.
(Withdrawn)
1045. PS-4517/1999 Helical-scan video tape cassette system using 12.65mm (0.5 in) in
IEC-961/1993 magnetic tape on type L.
(Withdrawn)
1046. PS-4518/1999 Helical – scan digital component video cassette recording system
IEC-1016/1989 using 19 mm magnetic tape (format D-1).
(Withdrawn)
1047. PS-4570-3/2000 Design of graphical symbols for use in the technical documentation
of products – Part-3: Classification of connecting nodes, networks
and their encoding.
(Based on IEC-81714-3/1998)
1048. PS-4571/2000 Measurement of exposure to radio-frequency electro-magnetic
fields- Field strength in the frequency range 100 k Hz to 1 GHz.
(Based on IEC-1566/1997)

1049. PS-4572-1-1/2000 Thermistors – Directly heated positive step-function temperature

coefficient. Part-1-1: Blank detail specification. Current limiting
application – Assessment level EZ.
(Based on IEC-738-1-1/1998)
1050. PS-4573-1/2001 Liquid crystal and solid-state display devices-
IEC- 61747-1/1998 Part 1: Generic specification.
(Withdrawn)
1051. PS-4573-2/2000 Liquid crystal and solid-state display devices.
Part 2: Liquid crystal display modules – Sectional specification.
(Based on IEC-61747-2/1998)
1052. PS-4573-2-1/2000 Liquid crystal and solid-state display devices-
Part-2-1: Passive matrix monochrome LCD modules –
Blank detail specification.
(Based on IEC-61747-2-1/1998)
1053. PS-4573-3/2001 Liquid crystal and solid-state display devices-
Part 3: Sectional specification for liquid crystal display (LCD) cells.
(Based on IEC-61747-3/1998)
1054. PS-4573-3-1/2001 Liquid crystal and solid-state display devices-
Part 3-1: Liquid crystal display (LCD) cells-
Blank detail specification.
(Based on IEC-61747-3-1/1998)
1055. PS-4574/2000 Spools for broadcast videotape recorders (VTRS).
(Based on IEC-503/1998)

1056. PS-4575/2000 Sound systems for emergency purposes.

 89

(Based on IEC-849/1998)

1057. PS-4576-1/2000 Digital audio tape cassette system (DAT) –

IEC-61119-1/1992 Part-1: Dimensions and characteristics.
(Withdrawn)
1058. PS-4576-2/2000 Digital audio tape cassette system (DAT) –
Part-2: DAT calibration tape.
(Based on IEC-61119-2/1991)

1059. PS-4576-3/2000 Digital audio tape cassette system (DAT) –

Part-3: DAT tape properties.
(Based on IEC-61119-3/1992)

1060. PS-4577/2000 Nuclear instrumentation – Sample containers for gamma-ray

spectrometry with Ge-detectors.
(Based on IEC-1428/1998)

1061. PS-4578-1/2000 Identification cards – Machine readable travel documents-

Part-1: Machine readable passport.
(Based on ISO/IEC-7501-1/1997)

1062. PS-4578-2/2000 Identification cards – Machine readable travel documents-

Part-2: Machine readable visa.
(Based on ISO/IEC-7501-2/1997)

1063. PS-4578-3/2000 Identification cards – Machine readable travel documents-

Part- 3: Machine readable official travel documents.
(Based on ISO/IEC-7501-3/1997)

1064. PS-4697/2001 Guide on the safety of multimedia equipment.

(Based on IEC-112/2000)

1065. PS-4698/2001 Mineral insulated thermocouple cables and thermocouples.

(Based on IEC-61515/1995)

1066. PS-4699/2001 Dimensions of panel areas and cut-outs for panel and rack-mounted
industrial-process measurement and control instruments.
(Based on IEC-60668/1980)

1067. PS-4700/2001 RF connectors, connector cable assemblies and cables-

Intermodulation level measurement.
(Based on IEC-62037/1999)
1068. PS-4701/2001 Nuclear reactors- Response time in resistance temperature detectors
(RTD) – In situ measurements.
(Based on IEC-61224/1993)
 90

1069. PS-4702/2001 Medical electrical equipment- Radionuclide calibrators- Particular

methods for describing performance.
(Based on IEC-61303/1994)

1070. PS-5212/2012 Methods of measurements for DVD players.

(Based on IEC-62389/2005)

………………………………….