Scribd
Upload
7 views

Line Coding

Line coding involves converting digital data into electrical signals for transmission. It maps 1s and 0s to voltage levels, such as high voltage for 1 and low voltage for 0. Various line coding techniques are used to address issues like errors, noise, complexity, and bandwidth. Common techniques include unipolar NRZ, polar NRZ, polar RZ, Manchester, and bipolar AMI/pseudoternary coding. Each have tradeoffs between complexity, bandwidth, and error detection capabilities.

Uploaded by

Saneh
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
7 views

Line Coding

Line coding involves converting digital data into electrical signals for transmission. It maps 1s and 0s to voltage levels, such as high voltage for 1 and low voltage for 0. Various line coding techniques are used to address issues like errors, noise, complexity, and bandwidth. Common techniques include unipolar NRZ, polar NRZ, polar RZ, Manchester, and bipolar AMI/pseudoternary coding. Each have tradeoffs between complexity, bandwidth, and error detection capabilities.

Uploaded by

Saneh
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 19

Line Coding

 Converting a string of 1’s and 0’s


(digital data) into a sequence of signals
that denote the 1’s and 0’s.
 For example a high voltage level (+V)
could represent a “1” and a low voltage
level (0 or -V) could represent a “0”.

4.1
Figure 4.1 Line coding and decoding

4.2
Mapping Data symbols onto
Signal levels
 A data symbol (or element) can consist of a
number of data bits:
 1 , 0 or
 11, 10, 01, ……
 A data symbol can be coded into a single
signal element or multiple signal elements
 1 -> +V, 0 -> -V
 1 -> +V and -V, 0 -> -V and +V

4.3
Line encoding C/Cs

 Error detection - errors occur during


transmission due to line impairments.
 Some codes are constructed such that
when an error occurs it can be
detected. For example: a particular
signal transition is not part of the code.
When it occurs, the receiver will know
that a symbol error has occurred.
4.4
Line encoding C/Cs

 Noise and interference - there are line


encoding techniques that make the
transmitted signal “immune” to noise
and interference.
 This means that the signal cannot be
corrupted, it is stronger than error
detection.

4.5
Line encoding C/Cs

 Complexity - the more robust and


resilient the code, the more complex it
is to implement and the price is often
paid in baud rate or required
bandwidth.

4.6
Figure 4.4 Line coding schemes

4.7
Unipolar

 All signal levels are on one side of the time


axis - either above or below
 NRZ - Non Return to Zero scheme is an
example of this code. The signal level does
not return to zero during a symbol
transmission.
 Scheme is prone to baseline wandering and
DC components. It has no synchronization or
any error detection. It is simple but costly in
power consumption.

4.8
Figure 4.5 Unipolar NRZ scheme

4.9
Polar - NRZ

 The voltages are on both sides of the time


axis.
 Polar NRZ scheme can be implemented with
two voltages. E.g. +V for 1 and -V for 0.

4.10
Polar - RZ
 The Return to Zero (RZ) scheme uses three
voltage values. +, 0, -.
 Each symbol has a transition in the middle.
Either from high to zero or from low to zero.
 This scheme has more signal transitions (two
per symbol) and therefore requires a wider
bandwidth.
 No DC components or baseline wandering.
 Self synchronization - transition indicates
symbol value.
 More complex as it uses three voltage level.
It has no error detection capability.
4.11
Figure 4.7 Polar RZ scheme

4.12
Polar - Biphase: Manchester and
Differential Manchester
 Manchester coding consists of combining the
NRZ-L and RZ schemes.
 Every symbol has a level transition in the middle:
from high to low or low to high. Uses only two
voltage levels.
 Differential Manchester coding consists of
combining the NRZ-I and RZ schemes.
 Every symbol has a level transition in the middle.
But the level at the beginning of the symbol is
determined by the symbol value. One symbol
causes a level change the other does not.

4.13
Figure 4.8 Polar biphase: Manchester and differential Manchester schemes

4.14
Note

In Manchester and differential


Manchester encoding, the transition
at the middle of the bit is used for
synchronization.

4.15
Note

The minimum bandwidth of Manchester


and differential Manchester is 2 times
that of NRZ. The is no DC component
and no baseline wandering. None of
these codes has error detection.

4.16
Bipolar - AMI and Pseudoternary
 Code uses 3 voltage levels: - +, 0, -, to
represent the symbols (note not transitions to
zero as in RZ).
 Voltage level for one symbol is at “0” and the
other alternates between + & -.
 Bipolar Alternate Mark Inversion (AMI) - the
“0” symbol is represented by zero voltage and
the “1” symbol alternates between +V and -V.
 Pseudoternary is the reverse of AMI.

4.17
Figure 4.9 Bipolar schemes: AMI and pseudoternary

4.18
Bipolar C/Cs

 It is a better alternative to NRZ.


 Has no DC component or baseline
wandering.
 Has no self synchronization because
long runs of “0”s results in no signal
transitions.
 No error detection.

4.19

You might also like