Directional Well Planning and Well Profile - Drilling Formulas and Drilling Calculati...

Page 1 of 7

About This Blog Contact Us Privacy Policy

About This Blog Contact Us Privacy Policy

SPONSORED SEARCHES

directional drilling vertical well drilling wellbore drilling

construction cost estimator oil well production drill pipe

Directional Well Planning and Well Profile Categories

By DrillingFormulas.Com February 18, 2017 - 11:30 pm Directional Drilling

Select Category 

 Post Views: 3,868

Get Drilling Formulas Sheet For Free

Subscribe to Get Free Calculation

Sheet
The well planning process starts from geologists and reservoir engineers who decide
email address
the best place for the wellbore. They may only need to determine a single target, which
will often be a tolerance of about 330 ft (100 m) around a certain target point. In this Click Here
case, the angle at which the well enters the target can have various degree of
deviation from the plan since a plan requires to hit only one target. On the other hand,
it might be necessary for the well to penetrate multiple targets, with the final target
Search on Drillingformulas.com
being increasingly complex. This requires what is known as “geosteering”, a process
which will be discussed later in the directional drilling series. The drilling engineer
therefore needs to examine potential surface locations (if more than one is available)
Search
and design a well path which meets all necessary target requirements at the lowest
Custom Search
possible cost. Cost can be minimized most effectively when there is a certain degree of
flexibility when it comes to the surface location.

Well Control One Page

Directional Well Profiles Drillingformulas.com on Facebook

Well profiles can be simply divided into two groups which are 2-D design and 3-D
design.

http://www.drillingformulas.com/directional-well-planning-and-well-profile/ 20/02/2020
Directional Well Planning and Well Profile - Drilling Formulas and Drilling Calculati... Page 2 of 7

2-D Well Profile Design …

The 2-D design well plan is a profile which inclinations are changed in order to hit
required target but it does not have or slightly change in azimuth. The example of 2-D
Like Page
well profiles are shown in figure 1-4.
Be the first of your friends to like this

OilfieldPix.com

Oilfield Acronyms

Figure 1 – J Profile (Build and Hold)

Recent Comments

Ahmad Alshammari on Possible Wellbore

Problems during Well Kill Operation

Ahmad Alshammari on Possible Wellbore

Problems during Well Kill Operation

DrillingFormulas.Com on Kill Weight Mud

DrillingFormulas.Com on Kill Weight Mud

Dellabani Mouloud on Driller’s Method

Quiz No. 1
Figure 2 – S Profile (Build and Drop)

http://www.drillingformulas.com/directional-well-planning-and-well-profile/ 20/02/2020
Directional Well Planning and Well Profile - Drilling Formulas and Drilling Calculati... Page 3 of 7

Figure 3 – Continuous Build

Figure 4 – J Profile + Continuous Build

3-D Well Profile Design

The 3-D well design have changes in both inclination and azimuth. The example of 3-D
well profiles is illustrated in figure 5.

http://www.drillingformulas.com/directional-well-planning-and-well-profile/ 20/02/2020
Directional Well Planning and Well Profile - Drilling Formulas and Drilling Calculati... Page 4 of 7

Figure 5 – 3D well profile (Gruenhagen, H et al., 2002)

Example of Well Planning

Figure 6 (Jones et al, 2008) provides an example of a planned well profile, from a
plane view and a vertical view. This is a relatively simple directional well, which is
designed to hit two targets, as shown by the boxes on the plan view. The easiest type
of directional well profile is a so-called “J-shaped profile”, which is a build and hold to
the target. The target in this case is an area, rather than a single point, and the well
need not therefore hit the center of the target. Although it is possible to hit small
targets, this increase in accuracy comes with a higher financial cost. In Figure 6, the
lower target will be hit on the edge nearest to the surface location.

Figure 6 – J Profile Directional well plan (Jones et al., 2008)

This method has several advantages:

http://www.drillingformulas.com/directional-well-planning-and-well-profile/ 20/02/2020
Directional Well Planning and Well Profile - Drilling Formulas and Drilling Calculati... Page 5 of 7

1. Opting for the nearest edge allows the well to be built to a lower inclination, and
therefore not as much hole needs to be drilled.

2. Should the well fail to build angle at a fast enough speed, then it could end up
missing its target. However, a higher build rate does not have a negative effect on
the drilling ROP. On the other hand, reducing the angle to reach the target will
mean compromising the drilling rate. This is caused by the fact that decreasing the
angle usually required removing weight from the bit. However, this does not apply
to all tools: some, such as rotary steerable tools, are exempt from this problem,
although come at a higher financial cost. Unless the drilling operation already has a
high daily cost, rotary steerable tools would not normally be used to correct a
directional issue. If the low edge is aimed at, then directional correction work will
not have a negative impact on drilling speed.

Other factors need to be taken into consideration when planning a well path.
Whenever the well changes direction, the drillpipe needs to bend around that curve,
and if the well is curved when still near the surface, this curve will cause additional
drillpipe tension the deeper the well gets and the more weight is put on the drillpipe.
This additional side force can cause numerous problems, including metal fatigue or
wear on the pipe, and may even cause the pipe to become completely stuck.

Rate of Change in Direction

Rate of change in direction is measured in angle of directional change for every 100 ft
(or 30 m) of hole drilled. This is known as the dogleg severity, as a dog’s leg bending is
a signifier of a bent hole. High dogleg severity needs to be avoided while at a shallow
point in the hole, since it causes high forces between the pipe and hole wall.

References

Gruenhagen, H., Hahne, U., & Alvord, G. (2002, January 1). Application of New
Generation Rotary Steerable System for Reservoir Drilling in Remote Areas. Society of
Petroleum Engineers.

Jones, S., & Sugiura, J. (2008, January 1). Concurrent Rotary-Steerable Directional
Drilling and Hole Enlargement Applied Successfully: Case Studies in North Sea,
Mediterranean Sea, and Nile Delta. Society of Petroleum Engineers.

Inglis, T.A. (2010) Directional drilling. Dordrecht: Springer-Verlag New York.

Technical, T., Astier, B., Baron, G., Boe, J.-C., Peuvedic, J.L.P. and French Oil & Gas
Industry Association (1990) Directional drilling and deviation control technology. Paris:
Editions Technip.

Short, J.J.A. (1993) Introduction to directional and horizontal drilling. Tulsa, OK:
PennWell Books.

Mitchell, R.F., Miska, S.Z. and Aadnoy, B.S. (2012) Fundamentals of drilling
engineering. Richardson, TX: Society of Petroleum Engineers.

VisCo (2011) Oil and gas – 3D animation – Shale drilling 02. Available at:
https://www.youtube.com/watch?v=RZgAVjCw3OI (Accessed: 18 February 2017).

http://www.drillingformulas.com/directional-well-planning-and-well-profile/ 20/02/2020
Directional Well Planning and Well Profile - Drilling Formulas and Drilling Calculati... Page 6 of 7

Records Cutting Settling in #1 Petroleum Deviating the

Management Deviated Wells Trading System - Wellbore by Jetting
Solutions Cause Stuck Pipe Simple & Affordable and Whipstock…

Ad Data Direct drillingformulas.com Ad enhelix.com drillingformulas.com

Share the joy
708

708
Shares

Tagged directional, drilling, planning, profile, well. Bookmark the permalink.

Office Interior Directional Drilling Why Directional Applications of

About DrillingFormulas.Com

Working in the oil field and loving to share knowledge.

View all posts by DrillingFormulas.Com →

« Why Directional Wells Are Drilled? Deviating the Wellbore by Jetting and
Whipstock (Directional Drilling) »

Leave a reply

Default Comments
(0)
Facebook
Comments

Leave a Reply

Comment


Name *

Email *

Website

Post Comment

0 Comments Sort by Oldest

Add a comment... 


Facebook Comments Plugin

This site uses Akismet to reduce spam. Learn how your comment data is processed.

http://www.drillingformulas.com/directional-well-planning-and-well-profile/ 20/02/2020
Directional Well Planning and Well Profile - Drilling Formulas and Drilling Calculati... Page 7 of 7

Drilling Formulas and Drilling Calculations | Powered by Mantra & WordPress.

http://www.drillingformulas.com/directional-well-planning-and-well-profile/ 20/02/2020