BULLETIN CS-10

Corporation Stops
and Injection Quills
Corporation Stops
Corporation Stops with injection quills are used for
injecting chemicals pumped by metering pumps into
tanks, mains, cooling towers and process systems. Quill
extends into the center of the stream providing more rapid
uniform dispersion of injected chemical.
Corporation Stop can be mounted to a “hot tap” which is installed
without draining the system. Corporation Stop allows injection quill
to be inserted
or removed
without having
to drain or shut
down the system.

• Use to 150 psi

• Available in CPVC, Kynar,
316SS and C-20
• Available in 1/2", 3/4" or
1" process connections
• Available with choice of MODEL CS2-75-PVC
Bronze or 316SS Corporation Stop

High Pressure
Injection Quills
High Pressure Injection Quills are used
to inject chemicals pumped by
metering pumps into the
turbulent flow zone of
high pressure water
or steam lines.
MODEL QC-316-50
• Use to 3,000 psi
• Spring loaded check valve
• Available in PVC, Kynar,
316SS and C-20
Sold by: G&W Industrial Sales
915 Emerson Avenue
Parkersburg, WV 26104
304-422-4755
[email protected]
Corporation Stops MODEL NO.
WITH
MODEL NO.
WITH MATERIAL PRESS. MAXIMUM
SIZE
(INCHES)
DIMENSIONS
(INCHES)
OF CONSTR. PSI TEMP.
with Quills BRONZE VALVE 316SS VALVE A B C D
CS2-50-PVC CS2-SS-50-PVC CPVC 125 psi 100°F (37°C) 1/2 NPT 7-3/4 5-1/4 2
CS2-75-PVC CS2-SS-75-PVC CPVC 125 psi 100°F (37°C) 3/4 NPT* 7-3/4 5-1/4 2
Features
CS2-100-PVC CS2-SS-100-PVC CPVC 125 psi 100°F (37°C) 1 NPT* 7-1/4 6-1/4 1-1/2
• Lever operated stop eliminates CS2-50-KY CS2-SS-50-KY Kynar 150 psi 200°F (93°C) 1/2 NPT 7-3/4 5-1/4 2-3/8
the need for a wrench CS2-75-KY CS2-SS-75-KY Kynar 150 psi 200°F (93°C) 3/4 NPT 7-3/4 5-1/4 2-3/8
• Protection chain prevents CS2-100-KY CS2-SS-100-KY Kynar 150 psi 200°F (93°C) 1 NPT 6-3/4 6-1/4 2
withdrawal before Corporation CS2-50-316 CS2-SS-50-316 316SS 150 psi 250°F (121°C) 1/2 NPT 7-1/2 5-1/4 2-3/8
Stop is closed CS2-75-316 CS2-SS-75-316 316SS 150 psi 250°F (121°C) 3/4 NPT 7-1/2 5-1/4 2-3/8
CS2-100-316 CS2-SS-100-316 316SS 150 psi 250°F (121°C) 1 NPT 6-1/2 6-1/4 2-3/8
• Operating pressures to 150 psi
CS2-50-C20 CS2-SS-50-C20 C-20 150 psi 250°F (121°C) 1/2 NPT 7-1/2 5-1/4 2-3/8
• Quill available in Corrosion- CS2-75-C20 CS2-SS-75-C20 C-20 150 psi 250°F (121°C) 3/4 NPT 7-1/2 5-1/4 2-3/8
resistant CPVC, Kynar, 316 stain- CS2-100-C20 CS2-SS-100-C20 C-20 150 psi 250°F (121°C) 1 NPT 6-1/2 6-1/4 2-3/8
less steel and Carpenter 20 *AWWA process connection available (add “AWWA” to end of model no.)
• Corporation Stop (bronze or 316SS) †Special lengths are available
available with 1/2", 3/4" or 1" up to 24" for CPVC & Kynar;
process connections up to 36" for 316SS &
Carpenter 20. Add suffix
• Inlet connection 1/2" female all models “-SP” to model no.

Recommendation
• Install a check valve and isolation valve at the inlet of the quill for ease of maintenance.

High Pressure Injection Quills

available with or without Check Valves
Features Recommendations
• Spring loaded check in QC models; no check in QB models • For lines smaller than 4" diameter,
• High pressure to 3,000 psi trim quill so chemical is released
near center of line. Use as is for
• Available in PVC, Kynar, 316 stainless steel and Carpenter 20
lines over 4" diameter.
MODEL WITH MODEL W/O MATERIAL MATERIAL MATERIAL PRESS. MAXIMUM CONN. SIZE
CHECK VALVE CHECK VALVE OF BODY OF CHECK OF SPRING (MAX.) TEMP. NPT • Install with “Telltale” V-notch
QC-PVC-50 QB-PVC-50 PVC Ceramic HAST C 150 psi 100°F (37°C) 1/2" facing upstream so flow strikes
QC-PVC-75 QB-PVC-75 PVC Ceramic HAST C 150 psi 100°F (37°C) 3/4" angled face at end of quill for
QC-316-50 QB-316-50 316SS 316SS HAST C 3000 psi 750°F (400°C) 1/2" most rapid dispersal of injected
QC-316-75 QB-316-75 316SS 316SS HAST C 3000 psi 750°F (400°C) 3/4" chemical.
QC-316-HPSE* — 316SS 316SS HAST C 3000 psi 750°F (400°C) 1/2" • For maintenance ease, installation
QC-C20-50 QB-C20-50 C-20 C-20 HAST C 3000 psi 750°F (400°C) 1/2" of an isolation valve, rated above
QC-KY-50 QB-KY-50 Kynar Ceramic HAST C 150 psi 200°F (93°C) 1/2" line operating
QC-KY-50T — Kynar Teflon HAST C 150 psi 200°F (93°C) 1/2" pressure,
QC-KY-75 QB-KY-75 Kynar Ceramic HAST C 150 psi 200°F (93°C) 3/4" immediately
*Has slotted end. behind the
†Special lengths quill is
are available recommended.
up to 24".
Add suffix “-SP”
to model no.

SOLD BY:
G&W Industrial Sales
915 Emerson Avenue
P.O. Box 247 • Lansdale, PA 19446-0247
Parkersburg, WV 26104
Tel: 215-699-8700 • Fax: 215-699-0370 304-422-4755
Toll-Free Tel: 1-888-3NEPTUNE (1-888-363-7886) [email protected]
Toll-Free Fax: 1-800-255-4017
Web Site: http://www.neptune1.com
E-mail: [email protected] © 2010 Neptune Chemical Pump Company All Rights Reserved Bulletin CS-10 P/N ZL105625 Printed in U.S.A.