Autodesk PowerMill

Robot
Training Manual
 PowerMill Robot Training

This manual deals with PowerMill Robot. It implies and assumes that the user has good
PowerMill skills. PowerMill Robot is used to convert tool paths in a machining project into
robot path following programs. It allows the user to simulate and analyse the final motion of
the robot. It is a Powerful integrated tool that can be used to analyse the robot simulation and
avoid problems like singularities or axes limits. PowerMill Robot is also used to create the final
robot program, without using third party software.

The Plugin Manager

PowerMill Robot is a plugin for PowerMill and information about it is contained within the plugin
manager within PowerMill.

To reveal PowerMill Robot once it is installed open the View menu on the ribbon menu and
select Show → Vertical Plugin Window.

Autodesk PowerMill Robot Training Manual 1

The Plugin manager allows the user a range of controls over the Plugins that have been
registered within PowerMill.

To access the plugin manager simple right click on the white area after the last pane, and
select Manage Plugins.

You can open the Plugin Manager at any time while PowerMill is running as demonstrated
above.

1 2

3
4

5 6

2 Robot Training Manual Autodesk PowerMil

This form has several sections to it:

1 Option to control if PowerMill searches for and runs plugins on startup.

2 One off control to load plugins if not loaded on start up.
3 The name and status of each of the Plugins that have been registered with
PowerMill.
The status icon to the left of the name indicates whether or not the Plugin is
enabled or disabled.

The green circle indicates the plugin is enabled while the red circle indicates that
it is disabled.

A grey status icon indicates that the Plugin is corrupt or incompatible with the
current version of PowerMill, information about why this may be the case is
listed in area 2.

4 Information about the plugin such as its name, description, location, author and
Global Unique Identifier (GUID).
Any errors affecting the plugin will also be listed here with potential solutions.

5 Options to enable or disable the Plugins.

Disabling Plugins could potentially improve PowerMill’s performance or

remove unnecessary items from the user interface, depending on the
Plugins functionality, without removing the Plugin entirely.
6 Access to the options form for the selected plugin
Below the enable/disable/options is information about the operation of the plugins.

7 The Plugin log file, this contains information about when the Plugins were loaded
and what events they are subscribed to in PowerMill, the Plugin manager also
provides users with the ability to clear this file for convenience.

Autodesk PowerMill Robot Training Manual 3

 Layout and Workflow
PowerMill Robot is organised to allow the user to follow a structured workflow, detailed below,
through the preparation of a process for the robot. This training manual assumes the user has
some experience with PowerMill and so toolpath calculation will not be covered.

1 Create the toolpaths for the robot to follow.

2 Select the robot that will be used.

3 Align the CAD in the virtual robot cell.

4 Constrain the robot and simulate the toolpaths.

5 Write the NC Program.

The toolpaths must be simulated in PowerMill robot before they can be output to the robot’s
native language.

The image below highlights the division of the tools into their separate areas.

1 2 3

1 The solution explorer contains the tools and entities that the user requires to create,
calculate and limit PowerMill toolpaths.

2 The graphical area is common to both PowerMill and PowerMill Robot and allows
visualisation of the processes being created.

3 The PowerMill Robot tabs area, contains all the options for constraining the robot’s
motion. This is subdivided into 4 tabs for the robot plugin. Each containing controls
required for a particular stage of the workflow.

4 The PowerMill Robot Simulation toolbar contains controls allowing the user to replay
saved robot simulation files and view the analysis of the saved simulations.

4 Robot Training Manual Autodesk PowerMil

 Workflow
PowerMILL robot has been developed to allow users to follow a prescribed workflow.

The idea and general structure of this workflow is outlined in the diagram.

1) Select a toolpath
2) Select robot cell

5) Write NC Program

3) Align CAD in cell

4) Simulate toolpath

Autodesk PowerMill Robot Training Manual 5

 PowerMill Robot Menus
PowerMill Robot is divided into 5 sections, with controls divided according to their position in
the workflow.

Robot Library Tab

Once the toolpaths have been created the next stage of the process is to select the robot that
will be used to complete the process.

The robot library provides an area to store all the robots available to the user. By default, the
standard robots are displayed for training purposes but these can be hidden from the options
menu in order to simplify the interface.

2 3 4 5 6
1

1 Show/Hide the robot cell. Has no effect on simulation simply toggles the display
status of the robot in the graphical interface to improve visibility of the part.

2 Open robot library, provides quick access to the folders containing the robot library
and the currently loaded robot as well as access to the list of user defined robots in
the library. The list can be edited to remove robots from the library when they are
no longer needed.

3 Add a new robot to the library, opens the form to add a new robot to the library.

4 Remove robot from the library

5 Refresh the library, if changes are made to any of the robot library files this button
may be required before the changes will take effect in the library.

6 Unload the robot, unloads the current robot used in simulation.

6 Robot Training Manual Autodesk PowerMil

 7 Available robot list, this lists all the robots currently saved in the Robot library and
allows the user to switch between robots by double clicking on the name of the
robot to be used.

The standard robots in the library are separated by manufacturer and sub divided by model,
with the library able to support multiple configurations of each robot model.

The divisions in the library are controlled by the file structure, the standard method of dividing
up the robots by model is recommended as they can share common CAD components and
therefore reduce the storage space required.

Adding a new Robot to the Library

1 On the Robot Library pane select Add a Robot to the library

2 In the dialog that appears NewLibrary enter the name that will appear as the main
point on the robot list

3 Displayed below as ExampleNewRobot enter the Robot name.

4 Select the folder that contains the mtd file to be added

5 When the folder is correctly selected the button Add robot to library is activated

Autodesk PowerMill Robot Training Manual 7

 If the add robot library button is not active, this means that the wrong
folder has been selected.

6 Select Add the robot to the library.

A new folder has now been created in the PowerMill robot library called
NewLibrary, containing the subfolder ExampleNewRobot, currently containing a
single configuration of the robot with the name drawn from the name of the
.mtd file, in this instance R2-6X-Spindle0.

When point 6 above is complete and the robot exists on your library, you may select the robot
form the list. This is done by double clicking the desired robot, you may double click anywhere
within the box below. This will import into PowerMill the machine tool.

If it is the first time the mtd file is added to PowerMill the menu below will open automatically.
After acknowledging the menu by clicking ok a new menu will then open. This is known as the
Robot Configuration menu, it is responsible for creating the RobConfig file. This file together
with the mtd file will define correctly the robot in PowerMill Robot.

To Follow the steps and read the explanations go to page 24 of this document.

Any errors made on the menus may result in serious errors while running
the file on the robot.

This menu is responsible for defining the Robot Manufacturer and Post
Processor selection amongst other things.

Depending on the options selected in this menu the correct functioning of

PowerMill Robot can be put at risk.

8 Robot Training Manual Autodesk PowerMil

 To Follow the steps and read the explanations of each tab go to the
chapter Robot Configuration Form of this document.

Removing robots from the library

1 To remove a robot from the library select the robot

2 Use the Remove robot from library button

1 To remove more than one robot or to edit a list with various entries of robots

2 Open Library Folder .

3 From the menu that appears select Open user defined robot library file.

The first time you open this file you are required to select a program to
open this file, select a text editor such as Notepad++ or WordPad.

This file lists all the custom robot cells available in the robot library.

4 Select the whole line defining the robot we added to the library. It should appear
similar to:

<Robot Folder="NewLibrary" Name="ExampleNewRobot"

MTDDirectory="*\PowerMillRobotTrainingData\Interface\RobotLibrary" />

5 Delete this line, starting at < ending at />. Save the file.

Autodesk PowerMill Robot Training Manual 9

 6 Click the Refresh Library button in PowerMill .

7 The robot has now been removed from the robot library.

Robot Cell Tab

The robot cell contains information about the cell configurations and allows control over the
default behaviour of the robot and the simulations.

Many of the tools are only required during installation or calibration of a robot.

2 3

4 5
6
7
9 10 11 12 8
13
18
Key: 14 15 16 17
1 Robot Configuration options, this contains information required to ensure the output
from PowerMill Robot can be interpreted by the robot controller. It is not expected
that these options will be modified during normal operation of the software. This
menu is respondible for the creation the RobConfig file, editing the RobConfig file
should be done via this menu.

2 The cell configuration combo box allows the user to choose between configurations
the user has previously created.

3 The Robot cell configuration editor allows the user to create new cell configurations
or edit existing ones. The user can control cell default behaviour such as tool or part
attach points, axis priorities, limits and home positions as well as simulation defaults
such as the default tool axis constraints.

4 The cell origin combo box allows the user to select which PowerMill workplane
positions the part correctly.

5 The Part Positioner allows the user to accurately position a part based on
measurements taken directly using the robot and the teach pendant.

10 Robot Training Manual Autodesk PowerMil

 6 The simulation safety settings allow the user to control whether the simulations are
checked for collisions between any machine parts or the part itself and control the
response and reporting of any singularities that may occur.

7 The display tool workplane option determines whether the workplane at the tip of
the tool is visible in the graphics window, this is useful when determining suitable
orientations of the tool for sections of toolpath.

8 The Rotation Tool Centre Point (RTCP) option when enabled will lock the position
and orientation of the tool relative to the part, any jogging of the robot from the
robot control tab will change the axis positions without altering the position or
orientation of the tool.

9 Show/Hide the robot toggle button

10 The Speed unit converter provides a useful tool to allow the user to easily convert
speeds from one unit system into other commonly used systems.

11 This option allows the user to create a workplane aligned to the tool workplane in its
current location.

12 The Virtual Teach Pendant provides the user with a tool similar to the pendant
attached to a robot cell to control the virtual cell. This allows the user to teach the
robot paths in an offline environment without the need for creating a toolpath.
There are also options to view tool position/coordinates and reorient the tool to
improve the process the robot is completing.

13 The help icon provides a second path to access the PowerMill Robot help files,
license options and options form.

14 The Tool and Spindle Calibration form is used to accurately measure the Spindle
centreline and position. This allows the user to accurately calculate the tool centre
point of new tools using just the protruding length of the tool from the reference
surface.

This method of measuring tools is more accurate than standard TCP

measurements as it can use the average of several measurements to
determine tool attach point and tool axis vector and simplifies the
introduction of new tools as the user only requires a length scale.

15 The workplane calculator provides an interface to view the transformations required

to convert the position of one workplane to another. Links to this interface can also
be accessed from the Fixture Offset Database and the Tool Database to allow tools
and fixtures to be added to the respective databases.

16 The rotary table calibration form provides an interface to enter measurements of 3

points around the axis of the rotary table in order to calculate the centre of rotation
and the axis of rotation. This information can be used to update of the .mtd file to
accurately represent the cell.

17 The transformation converter converts between standard rotation transformation

formats to allow interpretation of orientations reported by the robot.

18 Access to the options menu.

Autodesk PowerMill Robot Training Manual 11

 Robot Control Tab
The robot control tab provides methods to control the movement of the robot as it simulates
the toolpaths. It also contains direct controls for adjusting the robot axes positions.

1 2 3
4 5 6
7

10

11
Key:

1 The simulation controls allow the user to attach to the start point of the toolpath,
play through the simulation or perform a fast play through.

2 The return to simulation start option allows the user to return to the start of the
previous simulation restoring the robot axes to the exact positions they were in at
the start of the simulation.

3 The “Save Simulation” button allows the user to save the simulation as a Robot
simulation file, required to write the robot program.

4 The return to home button restores the robot to the home position for the current
robot configuration.

12 Robot Training Manual Autodesk PowerMil

 5 Allows the user to access a few options related to simulation files created
previously.

8
1
2
3
4
5
6
Key:
7
1 Load simulation file

2 Load simulation contraints (priorities, tool contraint etc)

3 Loads same as 2 plus cell configuration

4 Rename the simulation file

5 Delete the simulation file

6 Open simulation file

7 Open folder where simulation file is located

8 Provides back track compatability for older versions of PM Robot

6 The enable graphics option allows the user to toggle whether the simulation is
visible in the graphics window.

Running with graphics disabled will speed up the simulations but will not
give the user the ability to watch for possible problems with the process.
The full reporting of errors will still be available in the simulation toolbar
once the simulation is saved.

7 The trace axis limits tool will add visual ranges to the axis position bars to show the
travel that each undergoes during a process. This aids with optimisation of a
process.

8 The axis position controls report the current robot position along with an indication
of its proximity to its axis limit positions. Information about the axis address and
priority are also listed on the left hand side of this area.

The axis priorities and axis limits can be modified from this area by right
clicking on these values in this area.

Autodesk PowerMill Robot Training Manual 13

 9 The options tabs provide access to:

i. Tool Control – allows control of tool orientation

ii. Tools – provide various advanced tools

iii. Moves - manipulating the robot arm’s position

10 The Tool control menu

Provides a number of options for controling the orientation of the robot head
using either the orientation vectors or the tool axis.

There are 4 constrain types in the orientation vector [X], free, Orientation
vector, vector and follow. These control the X component of the tool workplane.

1 2 3 4

6
7

Key:

1 Free: The robot is able to use any orientation to reach each point on
the toolpath.

2 Align to Orientation Vector: At each point the x-axis of the tool

workplane should align to a given orientation vector. The toolpath
must have orientation vectors before the user can use this option,
these will be covered in more detail in a later chapter.

3 Align to a vector: At each point in the toolpath the x-axis of the tool
workplane will be forced to point in a fixed direction defined on this
menu of the PowerMill robot.

4 Align to Direction of travel: The x-axis of the tool vector is forced to

follow a direction defined relative to the direction of travel.

5 This will show the vector IJK values if the Vector option isused. The
values can also be set manually by numerical input.

6 Toleance will allow the simulation to diverge by from the setting used

by the degree that is displayed when the slider is dragged along.

14 Robot Training Manual Autodesk PowerMil

 7 Automatic Singularity avoidance will provide a toolpath free of
singularities.

8 10
9

Constraints to control the tool axis [Z], relative to the robot world
workplane.

These tools are only available when using a robot with one or
more external axes.

8 Free constraint, the tool axis vector is not controlled.

Vector constraint, the tool axis is limited to a specific vector, relative

to the robot world workplane. Vector values for IJK can be entered.

9 Plane constraint, the tool axis is constrained to a user defined plane.

11 The automatic wrist singularity avoidance option allows PowerMill to reorient the
robot to prevent alignment of axis 4 and 6, improving the consistency of the robots
speed. Singularities will be covered in more detail in a later chapter.

1 2 3
The Tools tab provides various advanced tools 4

5 6
7 8

1 Simulate multiple toolpaths allows the user to simulate various

toolpaths. Details on this menu are below.

2 The NC File import option allows the user to read in a pre-created NC

program for use in PowerMill Robot.

Autodesk PowerMill Robot Training Manual 15

 3 The Speed unit converter provides a useful tool to allow the user to
easily convert speeds from one unit system into other commonly used
systems.

4 The simulation safety settings allow the user to control whether the
simulations are checked for collisions between any machine parts or
the part itself and control the response and reporting of any collisions
that do occur.

5 The edit orientation vectors options provides tools to modify the

orientation of the tool at different points along the toolpath.
Orientation vectors will be covered in more detail in a later chapter.

6 The display number of points option gives information about the

number of points contained in the active toolpath. This can be useful
when working with controllers that have a limit on the number of
points a file can contain.

7 The Save robot position options allows the user to create a collection
of saved positions for the robot that can be loaded for use with later
toolpaths.

8 The load robot position option allows the user to load robot positions
previously saved by the user.

The Toolpath simulation allows the simulation of multiple toolpaths in one go.

1 Select all
1 2 3 4 5 6
2 Deselect all

3 Reverse selection

4 Start Simulation

5 Start Simulation in fast speed

mode 7 8
6 Stop simulation

7 Toolpath list

8 Simulation file details

9 Stop on issue

16 Robot Training Manual Autodesk PowerMil

The Moves tab provides manipulating tools to change the robot arm’s position

3
1 2 4

5
6
1 The linear jog controls move the tool linearly relative to the tool
workplane.

2 The rotary jog controls rotate the tool about the z-axis of the tool
workplane.

3 The Virtual Teach Pendant provides the user with a tool similar to the
pendant attached to a robot cell to control the virtual cell. This allows
the user to teach the robot paths in an offline environment without
the need for creating a toolpath. There are also options to reorient the
tool to improve the process the robot is completing.

4 The reverse the wrist option allows the user to switch between the 2
wrist orientations that are capable of achieving a given tool position
and orientation.

5 The Increment Option allows the user to control the linear distance or
rotation angle the robot will undergo when one of the jog controls is
used.

6 The lock external axes option allows the user to control how the
external axes behave when jogging the robot from this tab.

Autodesk PowerMill Robot Training Manual 17

Robot Program Tab

1
2 3
4

5 10

11

6 7 8 9
Key:

1 The robot name text is used as a name for the created program if no name is
entered, preferably an identifiable name should be used.

Program names must start with a letter to be run correctly by a number of

robot manufacturers.

2 The output workplane selection determines where the coordinates of each point are
measured from. Workplane will be output as number1.

3 The fixture offset database allows the user to choose the way PowerMill robot
outputs locations for the robot program. The fixture offset database will be covered
in a later chapter.

4 The NC program tab shows the program to be created and the parameters tab
provides access to user parameters that can be output in the robot program.

18 Robot Training Manual Autodesk PowerMil

 5 The NC program space contains the simulation files and transitions that will be
written into the robot program, the order in which they will be performed, and the
tool the robot will use.

6 The create new NC Program will create a new Robot NC Program for the PowerMill
project.

7 The load NC Program option will allow the user to load an NC program created
previously, allowing the user to save multiple NC Programs for the project.

8 The save NC program allows the user to save the NC Program they are currently
working on.

Saving the NC Program will not write the NC program.

9 The write robot NC program creates all the files necessary the user has to load onto
the robot controller to run the NC program.

10 The Parameter area allows the user to modify the user parameters that will be
written into the robot program.

11 The sub directory options controls whether the NC program is created within a sub
directory of the output location and whether any existing sub directories or files are
deleted when the NC program is written.

Autodesk PowerMill Robot Training Manual 19

 Simulation Replay Toolbar

1 2 3 4

5 6 7
Key:

1 Toolpath/NC program toggle switches between the simulation of the individual

toolpath and the NC program.

2 Allows the user to access a few options related to simulation files created
previously.

3 On the previous Robot Control Tab description, point 5, this option is discussed in
detail.

4 Simulation controls control the replay of the toolpath.

5 Simulation replay bar shows the position of the current point with in the overall
simulation and allows the user to dynamically control the replay of the simulation.

6 Expand simulation status control expands upon the simulation status and displays
any erros that may be present.

7 Simulation information contains detailed information about the toolpath.

8 Loop option allows the simulation to be replayed automatically when the end is
reached.

20 Robot Training Manual Autodesk PowerMil

Virtual Teach Pendant
1

4 2
3 5 6
8
7
10
11
9

13
Key: 12 12
1 Position display listing tooltip position, orientations and robot axis angles. These
values are editable to allow the tool to be accurately repositioned.

2 Toggle between pages allows the user to access the tools for applying point
parameters to the toolpath points.

3 Home the robot sends the robot to it’s home position.

4 Workplane selection allows the user to select which work plane the controls will
move the tooltip relative to.

5 Options to control whether the tooltip is allowed to move as the axes are rotated,
control whether the external axes move when the robot is jogged and whether the
path of the tool is traced.

6 Close the Virtual teach pendant.

7 Transition controls, clockwise from top: Load an existing transition file, save the
current transition as a Robot Simulation file, Close the current transition and Create
a new transition.

8 Play and stop the current robot motion.

9 Jogging controls, jog the robot parallel to the principal axes of the currently selected
workplane.

Autodesk PowerMill Robot Training Manual 21

 10 Speed controls, control the speed of the movements between points in the
transition.

11 Rotate controls, rotate about the axes of the tool workplane.

12 External axes controls, jog the external axis.

13 Undo the last movement controlled through the virtual teach pendant.

Robot Configuration Form

The Robot Configuration form can be found in the robot cell tab and stores information about
the robot and the default behaviour for the specific robot cell including how the toolpaths are
written to the robot’s native language.

The configuration manager stores the settings of the robot divided by the type of setting.

At any time the settings on the Robot Configuration Form might be

changed/edited.

The mtd and RobConfig file together are responsible for the correct definition of the robot in
PowerMill Robot.

The Robot Configuration Form is responsible for the creation of the RobConfig file.

22 Robot Training Manual Autodesk PowerMil

Robot Page

2
3
4
1

Key:

1 Configuration form navigation pane, used to move between the separate pages of
the Configuration form.

2 Enter a descriptive name for the robot.

3 Select the manufacturer of the robot, this is important as it will determine which
postprocessor files are available and which configurations are used for workplane
orientations and transformation conventions.

4 The robot kinematic determines whether the robot is holding the tool or the part.

Autodesk PowerMill Robot Training Manual 23

 Dimensions Page

The dimension’s page contains measurements, extracted from the mtd file, that allow the user
to confirm the robot is the correct model by verifying the vital dimensions.

MTD Information Page

The MTD information page lists information about the key locations of the tool attach point on
the robot and the location of the global transform, relative to the Robot World Workplane

24 Robot Training Manual Autodesk PowerMil

 Workplanes

The workplanes window allows you to define workplanes relative to the robot base (the
coordinates are measured relative to the origin of the exported CAD model). This allows the
user to check the positions of workplanes defined in real world cells and use them as outputs
in the robot code or for positioning parts.

The information about the robots 6 th axis workplane is also stored here and is used when
writing any tool information into the robot code.

On the right hand side is the check (Red Square in image above) position button allowing the
user to visualise the workplanes they have created.

Home Position

2
3

Autodesk PowerMill Robot Training Manual 25

 Key:

1 These options allow the user to load into 2 a predefined home position, using either
the current robot position, the position defined in the machine tool definition or use
a position defined in the active cell configuration.

2 These options display the Home Positoin, and allow the user to manually enter or
modify the home position of the robot.

3 This option sets the home position to always be the same as the one defined in the
current cell configuration. This will grey out the other controls on this page.

Simulation

Key:

1 These options determine which Solver will be used by the software. SimPost solvers
are compatible with up to 12 external axes, whereas the Pieper solver is only
compatible with 6 axis robots with no external axes.

2 These options deal with how tool changes are simulated in the software. The tool
change processes must be defined in the mtd file and there are examples of these in
the PowerMill Robot library.

3 The Modulo controls determine whether sending the robot to it’s 0 position will
instead send it to the nearest full rotation 0 position.

The controlled axes determine which axes the robot has control over in PM
Robot.

4 This option determines the kinematic of the robot. Parallel robot arms that keep the
top section of the arm at the same angle relative to the ground during movement of
axis 2 must have this option selected in order to simulate correctly.

26 Robot Training Manual Autodesk PowerMil

 Tool Database

1
2
3

The tool database page allows the user to choose where the tool information used by the robot
comes from. This choice will also affect what type of output will be in the postprocessed file.
There are 3 options:

1 This option relies on the Tool data saved on the robot controller, PowerMill will only
output a tool number to the code. This will be used by the controller to specify
what tool data is used, the relevant tool data is read from the robot’s tool database.

2 This option implies the “tool and spindle calibration” procedure has been completed.
This option is only avalible if the procedure has been completed and the data stored.

Tool data will be written on the file that will be loaded and run on the
robot.

The tool and spindle calibration allows the user to output the Tool data,
only having to measure the Gauge length.

PowerMill Tool database or PowerMill Robot database can be used for getting
the tool length.

Autodesk PowerMill Robot Training Manual 27

 If using PowerMill Tool database make sure the tool number is correct, as
this will be used to define the tool number in the NC program tab.

The Gauge length is used to calculate the Tool Data, so make sure the
tool is correctly defined.

Defining a Tool in PowerMill Robot database

2 3
1

28 Robot Training Manual Autodesk PowerMil

 1 From tool calibration menu open the Tool Length database

2 Select from list numerb of tool, define name

3 Enter gauge length as measured. This will define automatically the

tool data as X Y Z RX Ry Rz.

This will be written in the post processed file.

More information can be found in the help documentation: PowerMill

Robot - Tool and Spindle Calibration.pptx

3 This option will write the tool data on the post processed file.

The Tool data can be calculated from:

A – Tool & Spindle Calibration

B – Workplane calculator.

You may calculate the tool data and store it in the spreadsheet type list.

Fixture Offsets

3
4

Key:

1 Output workplane is fixed to the workplane that positions the robot.

This option should be used if the workplane used to position part is the same
as output workplane. Rotary table cell is a good example as the output
workplane is generally located on the top surface of tha rotary plate. On this
option, the Workplane number that is written in the output is fixed to 1.

Autodesk PowerMill Robot Training Manual 29

 2 Provides access to the Fixture Offset database where the user can add exact
locations of workplanes from virtual workplanes or from measured positions.

The number of the workplane written in the output can be chosen here, any
number can be chosen.

3 Choose which workplane on the cell to offset other workplanes from in the output.

4 With this option “On”, the Workplane Defenition (xyZ RxRzRz) will be written on the
post processed file. So this option defines whether the fixture data is written out, or
only the number is written, and so the fixture data saved on the controller is used.

Postprocessor

2
3

Key:

1 Options to select the postprocessor, or edit the selected postprocessor using the
button to the right.

The postprocessor files are xml documents and can be edited with a text
editor such as Notepad++.

More information about editing postprocessor files can be found in the help
documentation: PowerMill Robot – PostProcessors.pdf

2 Choose which workplane on the cell to offset other workplanes from in the output.

3 Choose whether to write fixture data to the robot code or use fixtures saved on the
controller. This option defines whether the fixture data is written out, or only the
number is written, and so the fixture data saved on the controller is used.

30 Robot Training Manual Autodesk PowerMil

 Loading the Robot Cell and Positioning
the Part
This manual assumes the user is familiar with toolpath creation using the PowerMill tools and
will therefore focus on the translation of these pre-created toolpaths into the robot NC
program.

To open PowerMill Robot Help folder that contains all the trainig material follow the steps
below:

1 On the Robot Library tab double click on the entry named R2-6X-
Spindle0+StaticTable. This will load the Robot cell.

2 Open the Robot Cell tab and click on the icon

3 From the menu that pops up select “Open help folder”

4 This will open the folder containing all the documentation

5 In windows explorer go up one level, and then open the

Library folder.

6 Once in the Library folder, open the folder named Projects.

This is where all the training projects are located.

With the project folder open, you are ready to start the training. You
may keep this folder open as projects from this folder will be required
later.

1 Load in the PowerMill project DemoToolControl6DWithFixture from

…\Library\Projects

2 Change the shading of the model to view the surface

3 From the View menu, Select the Iso 2 view

4 From the Robot Library tab expand the Autodesk list and expand the
Robot R2 list within the Autodesk folder.

5 Double click on the entry named R2-6X-Spindle0+StaticTable.

Autodesk PowerMill Robot Training Manual 31

 Double clicking on any name will load in that robot. Robots can be
replaced by double clicking on a different robot name, without the need to
unload the current robot first.

By default, the attach points for robots with no external axes is the robot
world workplane.

The location of the robot world workplane varies by manufacturer, but is

either at the base of the robot or just above it.

This workplane can be drawn at anytime from the Workplane Calculator or

the Robot Configuration manager in the Robot Cell tab.

6 From the robot cell tab click on the diplay robot, to hide it .

7 You can see that the part is positioned at the base of the robot

This is because the coordinate system of the CAD of the part is aligned to the
Robot world workplane.

8 In powerMill Create a new workplane located at 1000 -1000 530 and rename it table

This should be located at the right back corner of the table and have the
orientation as the workplane below.

32 Robot Training Manual Autodesk PowerMil

 Now the part needs to be positioned in a sensible position for machining. This
can be done in a number of ways.

We will position the part using a workplane located on the fixture, using
coordinates relative to the table workplane we just created.

If the part is already positioned in the robot cell, this positioning can be
replicated in PowerMill Robot by entering the part workplane location and
orientation. Use the robot measure a workplane using a position on the
part that can be replicated on the 3D model.

9 Record the position and rotation of this workplane from the robot controller.

On this example we will use XYZ position as 250, 800 and 125 and RxRyRz
Rotations as 0 0 0. We assume the controller supplied these values to us.

10 Create a workplane located and orientated as shown on the image below. Rename it
fixture.

11 Open the robot cell tab in PowerMill Robot and select the Part Positioning form.
Select table Workplane from the drop down menu for Reference workplane, the
measured workplane is the workplane on the fixture.

Autodesk PowerMill Robot Training Manual 33

 In most instances the robot world workplane will be the Reference
workplane. For a cell with only a robot, PowerMill global Transform will be
coincident to the robot world workplane.

12 Enter values for X, Y and Z of 250, 800 and 125 respectively.

Leave the values for Rz, Ry and Rx at 0.

These values will be given by the robot teach pendant, certain robot
manufacturers will give you the rotation values using a different method
and PowerMill robot can handle these in this form as well.

13 Apply this new position using the Set new origin button, close the menu.

14 Inspect the new position, the part and fixture should be just above the top of the
table and towards the back of the table surface. The part is now positioned and
ready to use.

Open the Part positioning form again. This time remove any selection
from Reference workplane, the menu should be empty as below.

34 Robot Training Manual Autodesk PowerMil

 Select fixture as the measured workplane. Enter XYZ as 1250 -200 655,
leave rotations as 0 0 0 and click set new origin. Close the menu when
finished.

The resulting position is exactly the same as this time we have used
coordinates relative to robot world workplane.

The most common practice is to measure workplanes on parts relative to

the robot world workplane. The Global transform for cells containing just a
robot have the robot world workplane coincident with PowerMill global
transform.

With an ABB IRB6640 PowerMill robot provides options to enter the

rotations as the Euler angles, or the robot convention, in this case
Quarternions

Autodesk PowerMill Robot Training Manual 35

 Creating a Robot Program
Robot Workplanes
Before any files are written it is important that the user understands robot workplanes,
measurements and transformations.

There are 2 key workplanes defined on the robot arm that the user needs to be aware of.

Robot World Workplane

The robot world workplane is normally defined at the base of the robot arm for cells containing
a single robot arm. Some manufacturers create the world workplane at the intersection of the
centre of rotation of axis 1 and axis 2. For more information, see the help documentation for
the specific robot manufacturer in use.

For cells where the robot arm holds the tool the part is positioned relative to the robot world
workplane.

These measurements are very important as it tells the robot where in the
cell the part is positioned.

6th Axis Workplane

The second workplane the user has to be aware of is the 6 th Axis Workplane. This is defined at
the centre of the flange face of the robot and moves with the 6 th Axis of the robot. The
orientation of the 6th Axis Workplane varies according to the manufacturer, for more
information see the help documentation for the specific robot manufacturer in use.

For cells where the robot is holding the tool the tool centre point is defined relative to the 6 th
Axis Workplane.

36 Robot Training Manual Autodesk PowerMil

For cells where the robot is holding the part; the part position is measured from the 6 th Axis
workplane, while the tool centre point is measured relative to the robot world workplane.

Writing the Robot Program

Once the part is positioned correctly within the cell the process that the robot will follow can
now be created.

All robot programs are created from PowerMill toolpaths and these must be created before
they are used in the robot program.

1 Activate the toolpath called Circle.

This is a simple profiling toolpath that will run round inside round pocket.

2 Expand the Robot Control tab.

3 Press the Home button followed by Attach to Start

Using the home button is not essential, however it will improve the
repeatability of the simulation as PowerMill robot will always attempt to
minimise axis movement when it attaches to the start of a toolpath.

Autodesk PowerMill Robot Training Manual 37

 Cell configurations can be used to modify the robots home position if
different joint orientations are desireable. This will be covered in a later
chapter.

4 Record a simulation using the Start Simulation button

This will play through the robot’s motions required to follow the toolpath.

At the moment the robot is not constrained in any way meaning it will look for
the simplest set of movements to reach the next point of the toolpath.

5 Save the simulation using the Save Simulation button

6 Give the simulation a unique, identifiable name, in this case Circle-FreeConstraints,

and press Save

A robot simulation file has now been created, these are the building blocks
of robot programs but are different to the files that can be uploaded to the
robot.

The post processed file that will run on the robot originates from the robot
simulation file.

The robot simulation files can be loaded into the simulation replay bar at
the bottom of the PowerMill window. When a new robot simulation file is
created it is automatically loaded in to the simulation replay toolbar.

7 View the project from the top

8 Zoom in so the whole toolpath is clearly visible.

9 Ensure that the Tool workplane is drawn by turning on the Display Tool Workplane
option in the Robot Cell tab

10 Either play through the simulation using the Play button or by dragging the
handle along the slider bar to view the simulation.

Notice how the x axis of the tool axis work plane is free to rotate at present. This
can be controlled to allow more precise control over the robot’s motion.

Y
X

38 Robot Training Manual Autodesk PowerMil

 11 Reopen the Robot control tab. Send the robot to the home position and then attach
to the start of the simulation.

An alternate way to ensure the same start position is used is to select

Move to Simulation Start Position . This will move the robot to the
start position of the currently loaded robot simulation file.

12 From the Tool control menu select Orentation vector[X], set it to vector and enter
IJK values of 1, 1, 0 respectively.

This will lock the x axis of the tool to be parallel to the x axis of the project.

Any modification made to the constraints of the toolpath will also require

the user to reattach the simulation to the start of the toolpath. If this
is not done, the new settings will not be applied.

13 Attach to the start of the toolpath, record the simulation and save it with the distinct
name, Full-VectorConstraints.

14 Play through the simulation again, noting the change in the robots control.

Autodesk PowerMill Robot Training Manual 39

 To view the previous simulation select Load a simulation file… this
will list all the simulation files for the current active toolpath. Hover the
cursor over the previously generated simulation file in the list. Select Load
simulation from the new flyout menu.

Once the simulation has been run and the user is happy with the result the simulation files can
be combined to create the robot program.

15 Open the Robot Program tab.

16 Enter a descriptive name in the Program Name field. In this case

TrimmingOperation-World.

Do not start program names with numbers as this will cause errors on
some controllers.

17 Leave the Output Workplane blank, this will select the measured workplane by
default.

18 Right click anywhere in the NC Program area, select add a toolpath.

This menu lists all the toolpaths that have robot simulation files associated with
them and allows the user to add them to the robot program.

Additionally this menu provides access to any other robot simulation file
available through the All Simulations option.

19 Select the Circle toolpath option and select Circle-VectorConstraints from the new
flyout menu.

This will add the selected simulation file to the robot program.

40 Robot Training Manual Autodesk PowerMil

 20 Click on to Open Fixture offset database

21 Make sure Write fixture offset data into robot program is ticked

22 Select Write robot NC program

A Windows Explorer Window will open up to the output directory for the NC
Program files.

This will contain 2 .txt files.

A robot program differs from a CNC machine NC program as it is divided into

separate files. This is to allow for the limited memory of a robot controller, each
file is limited to a certain number of points and these are only loaded when the
main file requires it. The main file in this instance is the one called
TrimmingOperation (the robot program name).

The exact structure of the robot NC program will depend on the robot
manufacturer.

The robot we are using in this example is an example robot only. While
the code is representative of a structure of a Robot program the output
from it will not work with any robot controllers.

23 Open the files with a text editor to inspect the NC program.

24 Save the NC Program .

The project has now been successfully post processed.

Autodesk PowerMill Robot Training Manual 41

 Changing the Output Workplane
If using the part position as the output workplane is not an option, for example if multiple
users are using the robot and may be modifying the location of measured userframes, then an
alternative can be selected.

The robot world work plane is a common reference point between the controller and PowerMill
robot so we will use that as an example of how to output the program using a different
workplane.

Any workplane used as the output must first be created within PowerMill.

1 Create a new NC Program . Name it TrimmingOperation-Fixture.

1 In the solution explorer on the left hand side of the screen expand the Workplanes
menu. There are 3 workplanes we will use now fixture as the output workplane.

2 Open Fixture offset database.

3 In the menu apply the settings below.

Make sure Simple Fixture Offset and Write fixture offset data into robot
program are selected.

4 On the position 5 line, double click the cell, a drop down menu will appear. Select
Fixture.

42 Robot Training Manual Autodesk PowerMil

 5 With Fixture selected as the workplane on line 5, Save the menu.

6 On the Output Workplane you will have now the same list of output workplanes as
on the fixture offset database.

Select 5 - Fixture

7 The menu should now look like this.

8 Select Write robot NC program

9 Open the recent created NC programs in a text editor and compare it to the
previous NC Program.

The difference between these 2 NC Programs will be that all the coordinates
have been transformed to reflect each individual point’s position relative to the
output workplane.

Using the robot world coordinate system makes it difficult to assess whether the machining will
occur in the correct location.

TrimmingOperation-Fixture has
coordinates relative to the
output workplane - fixture
(shown on the right/red).

Autodesk PowerMill Robot Training Manual 43

 TrimmingOperation-World has all coordinates relative to the Global
Transform of PowerMill (shown below in white)

This is because the Output workplane was left as empty, and this is the same
as selecting the Global Transform (white workplane), so all coordinates are
relative to this workplane.

If you open the file TrimmingOperation-World.txt on line 10 you will find the
base coordinates.

BASE[1] = [X 1547.343, Y 92.872, Z 660.000, A 0.0000, B 0.0000, C 0.0000]

This will overwrite any userframe saved in the identified position in the
robot controller user frame database. This will normally be position 1
(indicated by the integer in the square brackets BASE[1]) when using
PowerMill workplanes.

If you open the file TrimmingOperation-Fixture.txt on line 10 you will find the
base coordinates.

BASE[5] = [X 1250.000, Y -200.000, Z 655.000, A 0.0000, B 0.0000, C 0.0000]

Notice the default value when the output workplane is selected is 1, and in the
fixture offset menu will be the value you have selected, we selected 5.

If overwriting user frame 1 in the robot controller is not an option, then

the Fixture offsets can be used to write the output workplane location to a
separate entry in the Robot controller.

It is also possible to define as the output workplane a workplane defined

somewhere on the stock. And this one would be selected instead of the
global tranform.

44 Robot Training Manual Autodesk PowerMil

 Advanced Tool Controls
The Orientation vector [X] constraint was explored in the previous example but PowerMill
Robot has a range of other tools for controlling the movement of the robot during the
simulation and the operation.

There are three main methods to control the robot simulation:

▪ Tool workplane X axis control (done during the basic training)

▪ By editing the Robot Axes Limits and/or Priorities

▪ By using Orientation Vectors (which can also be set from simulation)

▪ Tool workplane Z axis control - Tool axis [Z] Constraint

In the previous example we used Orientation vector [X] that controls the X
component of the tool workplane. This menu, Tool axis [Z] , controls the Z axis
of the Tool.

Autodesk PowerMill Robot Training Manual 45

 Dynamic Axis Priorities and Limits
It is possible to change the axes movements that PRI will generate by changing which axes
PowerMill will prioritise, ie, which axes PowerMill will move significant amounts and which it will
try not to move. It is also possible to lock axes in static positions.

1 Load in the PowerMill project DemoToolControl2 from …\Library\Projects

2 Load the Robot cell from the library named R2-6X-Spindle0

3 Activate “Milling” Toolpath

4 Move robot to HOME

5 Set the tool axis constraint to free

6 Select static from the drop down menu

7 Jog manually the axis A to -11°

(This angle, the robot can reach

the whole toolpath without moving
axis A)

8 Turn Traxis Axis Limits on

This allows the user to visualise the maximum and minimum values the
individual axes reach during the simulation.

9 Attach to the start of the toolpath.

46 Robot Training Manual Autodesk PowerMil

 10 Play the simulation and watch the results to see the difference in process achieved.

Axis 1 will remain completely stationary, as shown by the axis limits sliders.

If any other constraint type is used in this example the solution will be
over-constrained and will not be able to reach all the positions.

External Axes
This can be used with external axes as well to control how they are used and whether they act
as positioners or an active part in the process.

This example will look at the use of Tool workplane X axis control constraints on a rotating
workpiece to further control the robot position.

1 Open project DemoBody2 (Rotary Z).

This project contains the surfaces for the torso of a figure to be machined from
polystyrene and some basic surface finishing toolpaths to achieve this.

2 From the robot library select and load robot: Autodesk, Robot R2, R2-7X-
Spindle0+RotaryTable.

3 Open the Robot Control tab and check the axis priorities.

The axis priorities for all the robot joints are set to Auto while the external axis
E1 is set to static.

4 From the solution explorer activate toolpath Full Spiral 30

5 Attach to the start of the toolpath and record the simulation.

Autodesk PowerMill Robot Training Manual 47

 With the current constraints the head of the robot is forced to move around the
part and reach over it to reach positions on the opposite side.

This will result in numerous collisions and the robot being unable to reach certain
positions of the toolpath.

Click anywhere in the graphics window to stop the simulation.

6 In the Robot Control tab send the robot to the home position.

Note the home position of axis E1 is at 0. We will update this to improve the
repeatability of the simulation later.

7 Alter the position of axis E1 to -90.

This can be done my typing the value in the position box followed by return.

8 Attach to the start of the toolpath.

9 Right click on the word auto below the E1 label in the Robot control tab. Change the
axis priority to High.

When any changes are made to axis priorities, constraint type or axis
limits you will need to reattach the robot to the start point of the toolpath.

10 Attach to the start of the toolpath

11 Play and record the simulation.

48 Robot Training Manual Autodesk PowerMil

 This PowerMill Robot Warning will pop up. Click on the Show issues to view what
is wrong.

12 PowerMill will open the Simulation issue menu.

On this menu we can see that there are a few Retract and reconfigure moves
required.

This is due to the fact that the toolpath is a full spiral and the limit of axis E1
is -720/720, so clearly the axis limit has been reached.

To overcome this issue:

1 – use an external axis with a higher limit, or no limit. powerMill wil

always need an upper limit enev if the hardware on the robot has no limit.

2 – change the toolpath to Bidirectional, as this will not exceed the limits.

13 Save the simulation and expand the analysis in the Simulation Replay bar

The simulation replay toolbar now reveals that the robot is constantly in a
singularity position throughout the toolpath, besides axis limit.

Autodesk PowerMill Robot Training Manual 49

 As the arm moves down the part the arm starts to come over the top of the tool.
While this may not cause a collision we want to constrain this further to avoid
any potential problems.

14 Activate the toolpath named Full Bidirectional 45°

15 Click on the Move to simulation Start Point icon

This will attach the Robot to the first point of the current toolpath with the
previous simulation settings.

16 Use the Teach Pendant to rotate the Robot around the Tool

This will rotate around the Z axis of the tool.

This will move the robot joint 5 away from the part, and also introduce an angle between joint
6 and 4. The angle between joint 6 and 4 will remove any wrist singularity.

50 Robot Training Manual Autodesk PowerMil

 An alternative to the Teach pendant is shown below.
Switch the Tool control area to the Moves Tab. Rotate the tool about the Z
axis

17 Make sure the Orientation vector [X] is set to vector, and

that Machine Tool Space is selected from the Tool Control
Tab.

18 Attach to the start of the toolpath

PowerMill Robot will read the vector to be used from the tool tips current
position and will update the IJK values automatically if the tool is
manually rotated.

Alternatively IJK values can be entered into the corresponding box to

precisely control the orientation of the tool

If you do not attach to the start after rotating around the tool and
applying the Orientation vector [X] tool constraint, there will be no
difference in the simulation.

Pay special attention to the exlamation mark on the Attach to start Icon.
This informs us that the simulation settings have changed and we need to
apply them by attaching to start.

19 Play and record the simulation.

This time the end result is quite different, the robot posture is maintained
throughout the toolpath and singularities are avoided by maintaining the
angle between axis 4 and 6.

Select Machine tool space from the drop down menu when using the
Orientation vector [X] on a rotary table.

Autodesk PowerMill Robot Training Manual 51

 This determines whether or not the coordinate system used to define the vector
rotates with the toolpath.

In Toolpath space the tool orientation will remain constant relative to the
dynamic surface of the table as it rotates.

In Machine tool space the orientation of the tool will remain constant relative to
the static robot world workplane. Regardless of the rotation of the part/toolpath.

52 Robot Training Manual Autodesk PowerMil

 Singularities
Singularities are a mathematical problem, for robots they are caused when 2 or more axes are
aligned resulting in an infinite number of combinations that will acieve the same tool position.
In other words if axis 4 and 6 are aligned (a wrist singularity) if axis 4 is rotated to 45 and
axis 6 is rotated to -45 it is the same as axis 4 being at 0 and axis 6 being at 0. Basically
any position where the rotation angles are equal and opposite.

This results in a large amount of axis rotation in areas around singularities. And will slow down
the operation of the robot arm.

There are 3 kinds of singularities:

1
2

Key:

1 Elbow singularity when axes 2, 3 and 5 are aligned

2 Alignment singularity, when axis 1 and 6 are aligned

3 Wrist singularity, when axis 4 and 6 are aligned

Singularities are especially detrimental to processes where the movement speed is important
to the process.

1 From the solution explorer activate toolpath Full Spiral 30

2 Send the robot to the home position.

Note that the robot restores all axes including the external axis to the 0 position.
This will undo the earlier rotational positioning of the axis.

The home position can be updated to improve repeatability of the simulation.

Autodesk PowerMill Robot Training Manual 53

 3 Select Move to Simulation start point

This restores all axes to their previous starting position, or to the last position
that attached to the tool to the first toolpath point.

This position can now be used to create the new home position.

4 From the robot cell tab open the virtual teach pendant

The virtual teach pendant is a software version of the teach pendant connected
to a robot to allow direct control of the robot position and to allow simple
movements to be taught directly from within the software.

5 Change the coordinate system in use to Tool-Tool.

This will alter the direction the tool tip will move in to be parallel to the axes of
the workplane at the tip of the tool.

6 Move the tool in the positive Z direction by 5 increments (press 5 times).

This will lift the tool away from the part along its own axis by 50 mm (or 5 times the
increment distance shown in the Move Speed field on the teach pendant).

54 Robot Training Manual Autodesk PowerMil

 7 Close the virtual teach pendant

8 Open the Cell Configuration Manager

The cell configuration manger controls the default properties for the robot cell
and allows the use of different positions, axis priorities and limits for different
parts of the robot operation.

9 Select New and enter an identifiable name for the cell configuration to be created.
In this instance HighTable

The values and settings in the database can be edited by double clicking
on any of them, alternatively the current settings can be quickly imported
using the 2 buttons in the top right hand corner of the menu.

Load Current Configuration will load in the current axis priorities and
limits as the defaults for the new configuration.

Load Current Position as HOME will update the home values of

each axis to match the current robot position.

10 Select Load Current Configuration and Load current Position as HOME

The changes made to the cell configuration will be highlighted in red in the table.

11 Save the new configuration and close the Cell Configuration Manager.

12 From the Cell Configuration drop down menu select HighTable.

Autodesk PowerMill Robot Training Manual 55

 The robot position will now update to the Home position set and change the axis
priority of axis E1 to High.

The only remaining issue is the Axis limits, in this instance PRI is reporting the simulation is
reaching the limit of axis E1, the rotary table.

In this case the limits on the axis are software limits and the axis itself is continuous. The
limits can be altered to reflect this in PowerMill.

13 Right click on the axis limits information underneath the position information in the
Robot Control tab.

14 Enter a high value for the maximum value that the axis is unlikely to reach, in this
case 10,000 and press enter.

An error message will pop up to warn you this is outside the limits of the axis as
defined by the mtd. Accept the message menu.

15 Repeat for Minimum, -10 000

This change will prevent the robot cell reorientating the table during the
operation, creating a smoother process, however it will still be flagged as an
error in the Simulation replay bar and the solution to this is to edit the values in
the mtd file. The process for this is covered in the help documentation however
it is beyond the scope of this training manual.

The changes to the toolpath (new start position and new axis limits) have not been added to
the cell configuration.

To edit a cell configuration

16 Open the Cell Configuration Manager from the Robot Cell tab.

17 Select edit and choose HighTable from the drop down menu of available cell
configurations.

18 Select Load Current Configuration and Load current Position as HOME

56 Robot Training Manual Autodesk PowerMil

 The changes made to the cell configuration will be highlighted in red in the table.

19 Save the edited configuration.

While the latest simulation is collision free and singularity free there may be times when more
control is desireable.

Direction of Travel
For certain operations the orientation of the tool needs to follow the direction of travel.

1 Close the project.

2 Reopen the project DemoToolControl2.

3 Load in the robot Autodesk Robot R2: R2-6X-Knife from the Robot Library.

4 From the robot cell tab select the workplane created earlier as the Cell Origin. The
name should have the form: (X1800,Y0,Z700,Rz0,Ry0,Rx0,ZYXr,,OnPart)

If the project was not saved after the last section the workplane will need
to be recreated. Open the Part Positionner form from the Robot Cell Tab,
select OnPart as the measured workplane and enter XYZ values of 1800 0
700 respectively.

5 From the Explorer window activate the Toolpath Knife.

6 In the Robot Control tab, select attach to start and record the simulation using the
default (free) constraint type.

7 Save the Simulation file.

PowerMill will display a warning to indicate that a collision has been detected.

Autodesk PowerMill Robot Training Manual 57

 Select continue.

If no warning pops up ensure that collision checking is switched on from

the Robot Cell tab.

8 Play through the simulation in the simulation replay bar until the first collision

As this is a knife cutting process the tool orientation must be relative to the
direction of travel of the tool.

9 From the robot control tab, send the robot to the home position, attach to the start
of the process.

10 Select Set Tool Control: Follow

This tool constraint type will align the x axis of the tool to the direction of travel.

11 Attach to the start of the process again and record the simulation.

12 Save the simulation as Knife-Follow.

The same message will be displayed warning of a collision.

13 Click continue.

14 Play through the simulation in the Simulation replay bar.

Inspecting the simulation replay it should become apparent that the x axis of the
tool workplane should actually be perpendicular to it, rather than parallel which
is the default for the follow constraint.

58 Robot Training Manual Autodesk PowerMil

 15 In the Tool control area of the robot control tab change the Angle value to 90.

16 Send the robot home, attach to the start of the toolpath, and record the simulation.

17 Save the simulation as Knife-Follow90.

18 Play through the simulation.

The tool will now orient with the x axis of the tool workplane aligned
perpendicular to the direction of travel.

Orientation Vectors
Orientation vectors are vectors created at each point along the toolpath which control the
direction the x-axis of the tool workplane will be oriented in.

Orientation vectors were created in each of the previous control types however no user
interaction was required to control the orientation of the tool so there was no need to display
them.

1 Unshade the model so the toolpath is clearly visible

Autodesk PowerMill Robot Training Manual 59

 2 Hide the robot so the tool and toolpath are the only entities visible

3 From the Toolpath toolbar turn on the visibility of the orientation vectors

This shows a graphical representation of the orientation the tool will be in at

each point along the toolpath.

Manipulating Orientation Vectors

In the previous examples a constant control was enough to create a good repeatable solution.
In certain instances different positions along the toolpath may require different orientations of
the tool.

Orientation vectors can be used to control these and PRI has a range of tools to create and
edit them.

There are 2 ways to create the orientation vectors on the toolpath:

▪ Created with the toolpath from the Machine Axis Control tab.

60 Robot Training Manual Autodesk PowerMil

 ▪ Saved with a successful simulation.

These 2 methods will have similar outputs and will be down to user preference.

Orientation Vectors from the Toolpath

1 Open the Toolpath Strategy Selector

2 From the Finishing options select Profile Finishing.

3 Change the name to OrientationVectorsTest.

4 From the graphics window select the surface.

5 Toggle to the Machine axis control tab.

6 From the dropdown menu for Orientation Type select Orientation vector.

7 There are now similar options to those contained within the PowerMill Robot for
orientation options, ie Free, Direction of travel and fixed direction.

8 Select fixed direction and enter values of 1 0 0 in the components area.

9 Calculate the Toolpath.

10 From the Toolpath toolbar turn on the visibility of the orientation vectors

11 Every toolpath point now has an orientation vector running parallel to the x axis of
PRI (IJK 1,0,0 the component values entered earlier).

Autodesk PowerMill Robot Training Manual 61

 12 To use the newly created orientation vectors select Set Tool Control: Orientation

Vector

13 Simulate the new toolpath.

The x axis of the tool will be locked to the x-axis direction.

Orientation Vectors from the Simulation

1 Open the PRI Options form. On the Automation page change the Save orientation
vectors from simulation to Ask before saving.

This option will give you the option to save the orientation vectors used in each
simulation when the simulation is saved. Always save will overwrite any existing
orientation vectors, each time a simulation is saved. Never save will not save the
orientation vectors used by the simulation.

2 With the OrientationVectorsTest toolpath still active. Select Set Tool Control: Vector.

62 Robot Training Manual Autodesk PowerMil

 3 Change the vector to IJK 0,1,0.

4 Attach to the start of the simulation, record the simulation and save the simulation
as OrientationVectorsTest.

If PRI warns of any collisions it is safe to continue as this is only an

example of functionality.

PRI will now give you the option to save the new Orientation Vectors.

Look at the current direction of the orientation vectors. If they are not visible

select No, tun on Orientation Vectors and repeat step 4.

5 Select Yes and observe the effect on the direction of the orientation vectors.

All the orientation vectors have now been rotated by 90 to be parallel to the Y-
axis of PRI.

Autodesk PowerMill Robot Training Manual 63

 Editing Orientation Vectors
Editting orientation vectors in individual regions of a toolpath can result in very flexible and
controllable simulations and solutions. We will now have a look at our options to edit
orientation vectors.

Selected Segment, Local Point and Region.

As the name implies, selected segment will act on a whole toolpath segment.

Local point will edit locally on a specific point where the tool/robot are located on the toolpath.
We will be able to define a blending distance for smoother transition.

Region works in a similar way to Local Point, but we use a boundary instead of the position of
the robot.

We will start by looking at selected segment.

1 Open the PowerMill project DemoToolControl6D

2 Load robot Autodesk: Robot R2: R2-6X-Spindle0.

3 From the Robot Cell tab open the part positioner and enter X1000 Y100 Z800

Click on Set new origin.

4 Activate the toolpath Pocket.

5 Simulate the toolpath, save the simulation as Pocket-Free.

6 Switch to the Tools section of the Robot Control tab

7 Open the Edit toolpath orientation vectors form

8 Draw the Orientation Vectors

64 Robot Training Manual Autodesk PowerMil

 These orientation vectors have been created automatically once the
simulation si saved. The orientation vectors can now be seen.

9 Switch to the moves section of the Robot Control tab. And rotate around the Z+ to
align the spindle like the image below.

X
Y

10 Select the toolpath segment (must be highlighted yellow).

11 On the Orientation vector editor menu:

Make sure you are on Selected segment tab and click apply orientation
vectors. The end result are brand new orientation vectors that can be used
for simulation.

12 Attach to the start and simulate.

13 Save the simulation as Pocket-SelectedSegment.

Autodesk PowerMill Robot Training Manual 65

 When a toolpath orientation vector is edited, by default the Orientation
vector[X] constraint applied will be Orientation vector.

We must resimulate after orientation vectors have been edited in order to

save the new tool orientation.

We will now look at Local point edit.

1 Activate the toolpath Outside.

2 Make sure the the Orientation vector[X] constraint is set to vector.

Set vector 1 0 0.

3 Attach to the start and simulate.

4 When saving the simulation a PowerMill message pops up.

5 If you click on Show issues, you can see that the robot cannot reach a specific
location.

By clicking on the message the tool will

be position on the place along the
toolpath that has the issue.

6 Save the simulation.

7 In the simulation replay bar the toolpath status bar is highlighting a potential
problem with the operation of the toolpath.

66 Robot Training Manual Autodesk PowerMil

 8 Expand the analysis section

The analysis area shows the source of the highlighted error is the robot is
approaching an axis limit.

As the simulation approaches the highlighted region it is clear that the robot
may not complete the the simulation correctly.

9 Using the simulation replay bar play through the simulation until the tip of the tool
is positioned at the closest point of the problem area.

10 Switch to the moves section of the Robot Control tab.

11 Rotate the robot about the z axis until the wrist (joint 5) is horizontal.

12 Switch to the Local Point tab on the orientation vector editor menu.

Autodesk PowerMill Robot Training Manual 67

 13 Enter a blend distance before of 100 and after of 350. Apply orientation vector.

These settings determine how far before/after the defined point the robot
will start reorienting itself to return to it’s previous orientation.

A higher value will reduce dwell time, but may cause issues in other areas.

14 Draw the Orientation Vectors make sure the edit is successful.

15 Replay the simulation and save it as Profile-Local.

The tool now enters the multiaxis region in a more suitable orientation and has
no axis limits and the simulation is successful.

The next example we will use a boundary to show the region option of the orientation vector
editor menu. On this menu, the vectors are edited inside a boundary, this will update all the
points contained within, plus an additional blend distance.

1 Activate the toolpath Full.

2 Ctrl+5 to view from the top and home the robot to get a clear view.

3 Open the orientation vector editor menu, use selected segment to apply orientation
vectors like image below.

4 Create a boundary like the image below, name it Region.

68 Robot Training Manual Autodesk PowerMil

 5 On the orientation vector editor menu, go to Region tab.

6 Here select the boundary Region, and leave the blend distance as 50.

The boundary will be projected down the z axis of a workplane and all points
that fall within that region can be altered simultaneously.

7 From the Moves area of the Robot Control tab rotate the robot about the Z
axis until the robot has a positon like image below

8 Click apply orientation vectors.

The orientation vectors within the boundary will all be updated according to the
robot position.

Autodesk PowerMill Robot Training Manual 69

 9 Simulate the toolpath.

Tool Axis Control [Z]

This is a new functionality added since PowerMill Robot 2017, and is controlling the Z Axis of
the tool throughout the toolpath.

It is only available when the Robot Cell has an external axis is Present.

We have seen previously that we can control the X component of the Tool via Orientation
Vector [X] in the Tool control tab. This menu will enable the control of the Z component of the
tool. These can be used separately, or together to control the movement of the tool during
simulation.

There are 3 options: Free, Vector and Plane. By default, it is set to Free.

1 Load the project DemoCylinderTrim.

2 Load in the robot Autodesk: R2-8X-Spindle0+Positioner

3 Activate the toolpath MultiAxis

4 Select View from Right (X), or hold (CTLR + 6)

5 Type 45 in E1 followed by return, that will position E1 at 45 degrees.

Type 90 in E2 followed by return, that will position E2 at 90 degrees.

70 Robot Training Manual Autodesk PowerMil

 6 Set E1 Priority to Auto

Set E2 to High.

Confirm that Tool Control is set to, Orientation Vector [X] – Free and Tool
axis [Z] – free

7 Attach to the start

8 Rotate around the Z of the tool in order to orientate the robot as below.

9 Play simulation & Save simulation file.

You will notice that during the simulation of the toolpath is conluded with no issues.

If you look closer at the tool orientation relative to the part, you will notice that the spindle
orientation changes a lot due to the toolpath Tool axis variation. E1 is static.

In order to reduce this, we will use the Tool Axis constraint. Follow the steps below to re-
simulate this time maintaining the tool axis constant throughout the toolpath.

1 Click on Move to Simulation start point

Set Tool Axis [Z] to Vector, Type in 0 1 1

Autodesk PowerMill Robot Training Manual 71

 2 Attach to the start

3 Play simulation

4 Save Simulation

The end result is different as the toolpath axis is maintained, E1 is moving more than before.
The Robot head is mostly static and the external axis compensate for the toolpath axis and
positions the part correctly, while maintining the tool/spindle orientation.

The Tool axis [Z] is only available on robot cells with external axis.

The Vector introduced is relative to the Robot World Workplane.

This is the same as the export workplane used to create the DMT
components.

Vector 0 1
1

Y
X

72 Robot Training Manual Autodesk PowerMil

 Plane works in a similar way. The tool is allowed to move within a
predefined 2D plane or another inputed workplane.

This is relative to Robot World Workplane.

YZ
Z
ZX
Y
XY
X

Autodesk PowerMill Robot Training Manual 73

 Transitions
The moves between toolpaths can be as important as the toolpaths themselves. These are
automatically calculated by PowerMill by default but can be controlled and programmed by the
user if required.

1 Load the project AutodeskEvoCar.

2 Load in robot Autodesk: Robot R2: R2-7X-Spindle0+LinearTrack

The car will be loaded at the base position of the robot.

3 From the Robot Cell tab set the Cell origin to be Center Right (Rail)

4 Activate toolpath SideWindow

5 From the Tool control tab, Set Orientation vector [X] to vector, type IJK

0,-0.452,-0.89.

In this instance as the toolpath is not attached to a rotating base the

Toolpath/Machine tool space option will not affect the output.

6 Attach to the start of the toolpath, simulate and save the simulation as SideWindow
3+2.

7 Activate toolpath RearNumberPlate

8 Send Robot to Home Position

9 Makse sure Tool Control is set to Free – Both Orientation Vector [X] and Tool Axis
[Z]

10 Attach to the start and play the simulation.

The robot is unable to reach areas of the toolpath due to the distance from the robot base.

74 Robot Training Manual Autodesk PowerMil

 11 Send the robot to it’s home position.

12 Use the position slider for Robot axis E1 to move the robot along the linear track to
a position at about 1000 mm

13 Attach to the start of the toolpath, repositioning the head and using Orientation
Vector [X] set to vector if necessary, simulate the toolpath and save the simulation
as RearNumberPlate.

Two simulation files have now been created and can be combined into a single Robot NC
program.

14 Open the Robot Program tab.

15 Name the Program DemoCar.

Right click in the NC program area, select Add a Toolpath, SideWindow,

SideWindow 3+2.

16 Repeat the procedure to add the RearNumberPlate simulation file.

Note the Simulation replay bar has been altered to NC Program mode and the replay bar is
now populated with two different coloured regions.

Autodesk PowerMill Robot Training Manual 75

The different coloured regions correspond to the separate toolpaths contained in the NC
Program while the white regions indicate areas where the robot is jogging axes to move
between toolpaths but no control is currently applied.

17 Play through the NC program from the simulation replay bar.

The robot travels straight through the part during the transition between the 2
toolpaths.

This can be resolved through the use of a transition.

18 Right Click in the NC program area, select add a transition and select Virtual Teach
Pendant

19 Select New

This provides us with options to

manually teach the robot a program,
similar to using a robot controller. Keep the Virtual Teach Pendant open.

20 On the NC replay bar use Go To Next Key point to move to the end of Toolpath 1

21 From the Virtual Teach Pendant select add .

This will save the last point of the toolpath as the first position in the transition.

76 Robot Training Manual Autodesk PowerMil

 22 From the Teach pendant, send the robot to home position.

23 Add this position to the transition

24 On the NC replay bar use Go To Next Key point to move to the Start of Toolpath 2.

25 Add the first point of this toolpath to the transition.

The transition should be made up of 3 points:

▪ The last point of toolpath SideWindow

▪ The robot home position

▪ The first point of toolpath RearNumberPlate.

Clicking on any
point in the transition
will move the robot to
that position.

Any position can be added to a transition, in this instance easy to identify

positions have been used to simplify the process.

Replaying from the start will also animate the transition. Select the first

point and press play in the teach penadant

26 Save the transition and name it ConnectingMove

27 Close the Virtual Teach Pendant

28 From the Robot Program tab right click in the NC Program area.

Autodesk PowerMill Robot Training Manual 77

 29 Select add a transition and select ConnectingMove

30 By default the transition is placed last in the NC program order

31 Select it and drag it on top of Rear Number Plate.

This will reorder the NC Program so that the transition happens between the 2
toolpaths.

The display in the Simulation Replay Toolbar has also been updated and the
blank space has been replaced by a pale blue segment to show the transition
has now been added and will be simulated.

32 Play through the simulation again to see the updated NC Program.

33 Write the robot NC program.

The writing process is the same regardless of the number of toolpaths or

transitions in the NC Program.

34 Close the project

78 Robot Training Manual Autodesk PowerMil

 Part on Robot
For a wide variety of applications, the part is carried by the robot to externally mounted tools.
PowerMill Robot can control these movements and simulate the processes.

1 Open project PartOnRobot_Blade

2 Load the robot Autodesk → R2 Robot → R2-6x-Polishing (PartOnRobot) into

PowerMill.

3 From the Robot Cell tab open the Cell Configuration Manager

4 From the drop down menu click through the different available configurations.

In this instance the difference between the configurations is the attach point
(where the tool is attached to the robot). Have a look at the different cell
configurations options.

5 Select cell configuration Station 1 – Milling.

6 Activate the toolpath Station 1 - Milling. Note where the tool is attached to the
machine tool.

7 Make sure Orientation Vector [X] and Tool Axis [Z] are set to Free

8 Attach to the start.

9 Simulate.

Autodesk PowerMill Robot Training Manual 79

 You will notice that the simulation is not smooth, and the part is constantly
changing orientation. This is not a desired robot motion.

10 Click on “Move to Simulation start position”

11 Use the Moves tab in Tool control to rotate around the Z

12 Set the Orientation Vector[X] to vector, rotate to the desired vector, in Toolpath
space, and attach to the start.

Toolpath space must now be used as the orientation of the tool is fixed
relative to the machine space.

Notice that rotating around the tool with Rz+ or Rz- will rotate the Part,
not the spindle.

13 Simulate the toolpath and save the simulation as Station 1 – Milling1.

This project already contains simulation files, do not writ eon top of them,
just rename the file. The original files might be useful later on.

14 Activate toolpath Station 2 - Edge grinding

15 From the Robot Cell tab change the Cell configuration to Station 2 - Grinding.

Note the new location of the tool in the cell.

16 Set the Orientation Vector[X] to vector: input the values 0, -1, 0 in Toolpath space,
and attach to the start.

17 Simulate the toolpath and save the simulation as Station 2 - Edge grinding1.

18 Set the Orientation Vector[X] to Free

19 Activate the toolpath Station 3 - Surface polishing and change the cell configuration
to Station 3 - Polishing.

20 Attach to the start and simulate.

In this case a grinding belt is being used and has in this case been simulated
with a tool at one of the drive wheels.

Care must be taken with toolpaths like this to ensure the part does not
collide with the belt.

80 Robot Training Manual Autodesk PowerMil

 21 Click on Move to Simulation start point

22 Set Orientation [X] to vector, and modify the position of the robot using the rotate
commands in the Moves area until the connected point is on a part of the tool on
the belt surface.

23 Simulate the toolpath and save as Station 3 - Surface polishing1.

24 Activate toolpath Station 4 - Flat belt polishing and use Cell configuration Station 4 -
Polishing (Flat Belt).

This example demonstrates a different method of defining a tool for a belt

which is to use a ballnose tool at the desired point of contact.

This method will produce more controllable simulations but will be difficult
to reproduce using a tool centre point measurement on the robot
controller. Solutions to this will be described later in this chapter.

25 Set Tool Control:Orientation [X] vector to Free

26 Attach to the start

27 Use the Moves tab in Tool control to rotate around the Z

28 Place the part parallel to the part floor, or horizontal.

Set Orientation [X] vector to vector, the current vector will be loaded
automatically, or set manually the values shown below.

29 Attach to the start

30 Simulate and save simulation as Station 4 - Flat belt polishing1.

31 Switch to the Robot program tab.

32 Open the NC program named Polishing

33 Ensure the output workplane is set to none (the global transform will be used).

34 Write the NC Program.

35 Open the file Polishing.txt.

Note that between module calls the tools are loaded/unloaded, but no tool
definitions are written in the code. They would appear after line 6 in the current
file.

36 This means that the tool definitions in use will be the tool definitions saved in the
controller with the corresponding tool number.

Autodesk PowerMill Robot Training Manual 81

 Notice that more simulations have been loaded than were simulated. This
is because the project already contained simulation files recorded
previously.

To select the cell configuration used for each simulation file. Activate the
toolpath, On the Simulation replay bar click on Load a Simulation file

Select Load a Simulation Strategy and cell configurations.

This ensures the correct tool attach point is active for each toolpath
simulation.

37 Activate Toolpath Station 1 – Milling

Use Load a Simulation Strategy and cell configurations to make sure the
correct cell configuration is active.

38 From the Robot Cell tab open the Robot Configuration Manager.

39 Switch to the tool database tab.

The tool database page contains the options that determine how the tool data
will be output in the code.

There are 3 options: Robot controller/Spindle calibration/Tool database.

The third option is only intended as a test as it would rely on the virtual
model of the tool to perfectly reflect the real cell.

40 Change the option selected to be Tool database.

The tools need to be added to the database.

41 Click add a new tool to the database

42 Create the Robot World Workplane, using the Robot workplane calculator

43 Select line 1 from the tool data base, as we are defining tool 1.

44 Select the robot World Workplane as the coordinate system.

45 Check the Use current tool workplane button and click Add to tool database.

82 Robot Training Manual Autodesk PowerMil

 46 Repeat the same process (step 38-46) for each of the different tool numbers used in
the different configurations, ensuring the tool is correctly located for the toolpath
each time.

The Tool menu wil be filled in with 5 tools, all tool data is now defined.

47 Write the NC Program and open the file Polishing.txt.

The file will now have the tool information written in it. It will appear similar to
the code shown below.
TOOL[1] = [X 80.617, Y 984.692, Z -648.728, R1 0.0000, R2 -90.0000, R3 -90.0000]

TOOL[2] = [X 1290.195, Y -392.704, Z 702.190, R1 0.0000, R2 -90.0000, R3 90.0000]

TOOL[3] = [X 451.409, Y -1447.742, Z 770.200, R1 -66.1840, R2 0.0000, R3 -90.0000]

TOOL[5] = [X -821.400, Y -1148.400, Z 1641.000, R1 -154.5530, R2 -80.4590, R3 -174.0860]

TOOL[4] = [X -901.237, Y -1211.939, Z 1485.872, R1 31.4430, R2 0.0000, R3 90.0000]

Depending on the manufacturer the tool Workplane can be the either the
cutting tool or the actual part on the robot. Check this on the
manufacturer manual.

Autodesk PowerMill Robot Training Manual 83

 The Options Form
Clicking on the Options Form in the Plugin Manager while the Robot plugin is selected will
provide access to a number of options that control the operation of PowerMill robot.

Directories

1 2

Key:

1 Options tabs list, used to navigate between different options menus within the form.

2 Robot data options, determines where the data generated by PowerMill robot is
saved. The default is to save it within the PowerMill project file.

3 Control allowing the user to determine whether or not the standard robots appear in
the library tab in PowerMill robot (Changes take effect the next time the robot
library is refreshed).

4 Link to the folder containing the PowerMill Robot Help documentation

84 Robot Training Manual Autodesk PowerMil

Automation

Key:

1 These options control whether the previous simulation file is loaded by PowerMill
robot when the associated toolpath is activated.

2 This option controls whether orientation vectors are created when the toolpath is
simulated. Once orientation vectors have been created they can be used to
constrain the toolpath for future simulations.

3 These options control whether vectors and orientation vectors are automatically
updated when the tool is jogged into a position by the user.

Autodesk PowerMill Robot Training Manual 85

Analysis

Key:

1 These settings determine how close the robot has to be to a singularity position to
be highlighted as a potential issue within the simulation toolbar.

1 These settings determine how close the robot has to be to an axis limit to be
highlighted as a potential issue within the simulation toolbar.

2 This option allows the completed simulation to be loaded into the advanced
simulation plugin for analysis of the robot motion while it follows the toolpath.

86 Robot Training Manual Autodesk PowerMil

Simulation

Key:

1 These are the options allowing the user to switch on or off the collision checking for
PowerMill robot.

2 These options control the frequency of points within a transition path to allow for
simulation and control of the robot path in the cell.

Autodesk PowerMill Robot Training Manual 87

Singularity Avoidance

Key:

1 This option controls how close to a singularity position a robot will be allowed to get
before PowerMill robot will attempt to automatically reorient the axes to avoid the
singularity.

2 These settings determine the behaviour PowerMill will follow to avoid a singularity.

Step determines the increments PowerMill will alter the orientation vector angle
by when searching for a singularity free solution.

Maximum step controls the maximum deviation angle from the original tool
orientation that PowerMill is allowed to use.

Distance per degree controls how sharply the robot will move into the new
orientation, i.e. 10mm required per degree rotated, this is used to smooth the
transition.

88 Robot Training Manual Autodesk PowerMil

Display

Key:

1 These options control the appearance and settings related to the tool tip trace or the
path of the tool tip relative to either the machine tool space or the part.

1 These options control how the names of the axes appear in the Robot Control tab
and in the virtual teach pendant.

2 These options allow the user to control how many rows appear in the tool and
fixture offset forms and therefore how many can be used in a robot program.

Autodesk PowerMill Robot Training Manual 89

Virtual Teach Pendant

2
3

Key:

1 hese settings allow the user to control the increments that the robot will move by
when using the Virtual Teach Pendant in each of the speed settings.

1 This option controls how the tool orientation is displayed in the Virtual Teach
Pendant.

2 This option allows the user to use a 3D mouse to control the axes and position of
the robot

90 Robot Training Manual Autodesk PowerMil

Miscellaneous

Key:

1 This option allows the user to control how the external axes behave when the user
attaches to the start of the toolpath.

2 This will open a folder with 2 files.

Application.cfg and Application.mac

Application.mac should not be edited or moved, as it is the start up macro

for PowerMill Robot. This File allows the user to modify the processes and
commands that are run when the first robot is loaded into the PowerMill

Application.cfg is PowerMill Robot configuration file, where the user

preferences are saved.

This file has direct influence on some options inside powerMill Robot, some of
these are for example:

Control how the names of the axes appear in the Robot Control tab and in
the virtual teach pendant.

How many rows or numbers of tools that appear in the tool and fixture offset
forms and therefore how many can be used in a robot program.

Autodesk PowerMill Robot Training Manual 91

Autodesk Legal Notice

© 2020 Autodesk, Inc. All Rights Reserved. Except where otherwise

noted, this work is licensed under a Creative Commons Attribution-
NonCommercial-ShareAlike 3.0 Unported License that can be viewed
online at http://creativecommons.org/licenses/by-nc-sa/3.0/. This
license content, applicable as of 16 December 2014 to this software
product, is reproduced here for offline users:
CREATIVE COMMONS CORPORATION IS NOT A LAW FIRM AND DOES
NOT PROVIDE LEGAL SERVICES. DISTRIBUTION OF THIS LICENSE
DOES NOT CREATE AN ATTORNEY-CLIENT RELATIONSHIP. CREATIVE
COMMONS PROVIDES THIS INFORMATION ON AN "AS-IS" BASIS.
CREATIVE COMMONS MAKES NO WARRANTIES REGARDING THE
INFORMATION PROVIDED, AND DISCLAIMS LIABILITY FOR DAMAGES
RESULTING FROM ITS USE.

License
THE WORK (AS DEFINED BELOW) IS PROVIDED UNDER THE TERMS
OF THIS CREATIVE COMMONS PUBLIC LICENSE ("CCPL" OR
"LICENSE"). THE WORK IS PROTECTED BY COPYRIGHT AND/OR
OTHER APPLICABLE LAW. ANY USE OF THE WORK OTHER THAN AS
AUTHORIZED UNDER THIS LICENSE OR COPYRIGHT LAW IS
PROHIBITED.
BY EXERCISING ANY RIGHTS TO THE WORK PROVIDED HERE, YOU
ACCEPT AND AGREE TO BE BOUND BY THE TERMS OF THIS LICENSE.
TO THE EXTENT THIS LICENSE MAY BE CONSIDERED TO BE A
CONTRACT, THE LICENSOR GRANTS YOU THE RIGHTS CONTAINED
HERE IN CONSIDERATION OF YOUR ACCEPTANCE OF SUCH TERMS
AND CONDITIONS.

92 Robot Training Manual Autodesk PowerMil

 1. Definitions
a. "Adaptation" means a work based upon the Work, or upon the Work
and other pre-existing works, such as a translation, adaptation,
derivative work, arrangement of music or other alterations of a
literary or artistic work, or phonogram or performance and includes
cinematographic adaptations or any other form in which the Work
may be recast, transformed, or adapted including in any form
recognizably derived from the original, except that a work that
constitutes a Collection will not be considered an Adaptation for the
purpose of this License. For the avoidance of doubt, where the Work is
a musical work, performance or phonogram, the synchronization of
the Work in timed-relation with a moving image ("synching") will be
considered an Adaptation for the purpose of this License.
b. "Collection" means a collection of literary or artistic works, such as
encyclopedias and anthologies, or performances, phonograms or
broadcasts, or other works or subject matter other than works listed
in Section 1(g) below, which, by reason of the selection and
arrangement of their contents, constitute intellectual creations, in
which the Work is included in its entirety in unmodified form along
with one or more other contributions, each constituting separate and
independent works in themselves, which together are assembled into
a collective whole. A work that constitutes a Collection will not be
considered an Adaptation (as defined above) for the purposes of this
License.
c. "Distribute" means to make available to the public the original and
copies of the Work or Adaptation, as appropriate, through sale or
other transfer of ownership.
d. "License Elements" means the following high-level license attributes
as selected by Licensor and indicated in the title of this License:
Attribution, Noncommercial, ShareAlike.
e. "Licensor" means the individual, individuals, entity or entities that
offer(s) the Work under the terms of this License.
f. "Original Author" means, in the case of a literary or artistic work,
the individual, individuals, entity or entities who created the Work or if
no individual or entity can be identified, the publisher; and in addition
(i) in the case of a performance the actors, singers, musicians,
dancers, and other persons who act, sing, deliver, declaim, play in,
interpret or otherwise perform literary or artistic works or expressions
of folklore; (ii) in the case of a phonogram the producer being the
person or legal entity who first fixes the sounds of a performance or
other sounds; and, (iii) in the case of broadcasts, the organization
that transmits the broadcast.

Autodesk PowerMill Robot Training Manual 93

 g. "Work" means the literary and/or artistic work offered under the
terms of this License including without limitation any production in the
literary, scientific and artistic domain, whatever may be the mode or
form of its expression including digital form, such as a book, pamphlet
and other writing; a lecture, address, sermon or other work of the
same nature; a dramatic or dramatico-musical work; a choreographic
work or entertainment in dumb show; a musical composition with or
without words; a cinematographic work to which are assimilated
works expressed by a process analogous to cinematography; a work
of drawing, painting, architecture, sculpture, engraving or
lithography; a photographic work to which are assimilated works
expressed by a process analogous to photography; a work of applied
art; an illustration, map, plan, sketch or three-dimensional work
relative to geography, topography, architecture or science; a
performance; a broadcast; a phonogram; a compilation of data to the
extent it is protected as a copyrightable work; or a work performed by
a variety or circus performer to the extent it is not otherwise
considered a literary or artistic work.
h. "You" means an individual or entity exercising rights under this
License who has not previously violated the terms of this License with
respect to the Work, or who has received express permission from the
Licensor to exercise rights under this License despite a previous
violation.
i. "Publicly Perform" means to perform public recitations of the Work
and to communicate to the public those public recitations, by any
means or process, including by wire or wireless means or public digital
performances; to make available to the public Works in such a way
that members of the public may access these Works from a place and
at a place individually chosen by them; to perform the Work to the
public by any means or process and the communication to the public
of the performances of the Work, including by public digital
performance; to broadcast and rebroadcast the Work by any means
including signs, sounds or images.
j. "Reproduce" means to make copies of the Work by any means
including without limitation by sound or visual recordings and the
right of fixation and reproducing fixations of the Work, including
storage of a protected performance or phonogram in digital form or
other electronic medium.
2. Fair Dealing Rights. Nothing in this License is intended to reduce,
limit, or restrict any uses free from copyright or rights arising from
limitations or exceptions that are provided for in connection with the
copyright protection under copyright law or other applicable laws.

94 Robot Training Manual Autodesk PowerMil

 3. License Grant. Subject to the terms and conditions of this License,
Licensor hereby grants You a worldwide, royalty-free, non-exclusive,
perpetual (for the duration of the applicable copyright) license to
exercise the rights in the Work as stated below:
a. to Reproduce the Work, to incorporate the Work into one or
more Collections, and to Reproduce the Work as incorporated in
the Collections;
b. to create and Reproduce Adaptations provided that any such
Adaptation, including any translation in any medium, takes
reasonable steps to clearly label, demarcate or otherwise identify
that changes were made to the original Work. For example, a
translation could be marked "The original work was translated from
English to Spanish," or a modification could indicate "The original
work has been modified.";
c. to Distribute and Publicly Perform the Work including as
incorporated in Collections; and,
d. to Distribute and Publicly Perform Adaptations.
The above rights may be exercised in all media and formats whether
now known or hereafter devised. The above rights include the right to
make such modifications as are technically necessary to exercise the
rights in other media and formats. Subject to Section 8(f), all rights
not expressly granted by Licensor are hereby reserved, including but
not limited to the rights described in Section 4(e).

Autodesk PowerMill Robot Training Manual 95

 4. Restrictions. The license granted in Section 3 above is expressly
made subject to and limited by the following restrictions:
a. You may Distribute or Publicly Perform the Work only under the
terms of this License. You must include a copy of, or the Uniform
Resource Identifier (URI) for, this License with every copy of the
Work You Distribute or Publicly Perform. You may not offer or
impose any terms on the Work that restrict the terms of this
License or the ability of the recipient of the Work to exercise the
rights granted to that recipient under the terms of the License. You
may not sublicense the Work. You must keep intact all notices that
refer to this License and to the disclaimer of warranties with every
copy of the Work You Distribute or Publicly Perform. When You
Distribute or Publicly Perform the Work, You may not impose any
effective technological measures on the Work that restrict the
ability of a recipient of the Work from You to exercise the rights
granted to that recipient under the terms of the License. This
Section 4(a) applies to the Work as incorporated in a Collection,
but this does not require the Collection apart from the Work itself
to be made subject to the terms of this License. If You create a
Collection, upon notice from any Licensor You must, to the extent
practicable, remove from the Collection any credit as required by
Section 4(d), as requested. If You create an Adaptation, upon
notice from any Licensor You must, to the extent practicable,
remove from the Adaptation any credit as required by Section 4(d),
as requested.

96 Robot Training Manual Autodesk PowerMil

 b. You may Distribute or Publicly Perform an Adaptation only
under: (i) the terms of this License; (ii) a later version of this
License with the same License Elements as this License; (iii) a
Creative Commons jurisdiction license (either this or a later license
version) that contains the same License Elements as this License
(e.g., Attribution-NonCommercial-ShareAlike 3.0 US) ("Applicable
License"). You must include a copy of, or the URI, for Applicable
License with every copy of each Adaptation You Distribute or
Publicly Perform. You may not offer or impose any terms on the
Adaptation that restrict the terms of the Applicable License or the
ability of the recipient of the Adaptation to exercise the rights
granted to that recipient under the terms of the Applicable License.
You must keep intact all notices that refer to the Applicable License
and to the disclaimer of warranties with every copy of the Work as
included in the Adaptation You Distribute or Publicly Perform. When
You Distribute or Publicly Perform the Adaptation, You may not
impose any effective technological measures on the Adaptation
that restrict the ability of a recipient of the Adaptation from You to
exercise the rights granted to that recipient under the terms of the
Applicable License. This Section 4(b) applies to the Adaptation as
incorporated in a Collection, but this does not require the Collection
apart from the Adaptation itself to be made subject to the terms of
the Applicable License.
c. You may not exercise any of the rights granted to You in Section
3 above in any manner that is primarily intended for or directed
toward commercial advantage or private monetary compensation.
The exchange of the Work for other copyrighted works by means of
digital file-sharing or otherwise shall not be considered to be
intended for or directed toward commercial advantage or private
monetary compensation, provided there is no payment of any
monetary compensation in connection with the exchange of
copyrighted works.

Autodesk PowerMill Robot Training Manual 97

 d. If You Distribute, or Publicly Perform the Work or any
Adaptations or Collections, You must, unless a request has been
made pursuant to Section 4(a), keep intact all copyright notices for
the Work and provide, reasonable to the medium or means You are
utilizing: (i) the name of the Original Author (or pseudonym, if
applicable) if supplied, and/or if the Original Author and/or Licensor
designate another party or parties (e.g., a sponsor institute,
publishing entity, journal) for attribution ("Attribution Parties") in
Licensor's copyright notice, terms of service or by other reasonable
means, the name of such party or parties; (ii) the title of the Work
if supplied; (iii) to the extent reasonably practicable, the URI, if
any, that Licensor specifies to be associated with the Work, unless
such URI does not refer to the copyright notice or licensing
information for the Work; and, (iv) consistent with Section 3(b), in
the case of an Adaptation, a credit identifying the use of the Work
in the Adaptation (e.g., "French translation of the Work by Original
Author," or "Screenplay based on original Work by Original
Author"). The credit required by this Section 4(d) may be
implemented in any reasonable manner; provided, however, that in
the case of a Adaptation or Collection, at a minimum such credit
will appear, if a credit for all contributing authors of the Adaptation
or Collection appears, then as part of these credits and in a
manner at least as prominent as the credits for the other
contributing authors. For the avoidance of doubt, You may only use
the credit required by this Section for the purpose of attribution in
the manner set out above and, by exercising Your rights under this
License, You may not implicitly or explicitly assert or imply any
connection with, sponsorship or endorsement by the Original
Author, Licensor and/or Attribution Parties, as appropriate, of You
or Your use of the Work, without the separate, express prior
written permission of the Original Author, Licensor and/or
Attribution Parties.
e. For the avoidance of doubt:
i. Non-waivable Compulsory License Schemes. In those
jurisdictions in which the right to collect royalties through any
statutory or compulsory licensing scheme cannot be waived, the
Licensor reserves the exclusive right to collect such royalties for
any exercise by You of the rights granted under this License;

98 Robot Training Manual Autodesk PowerMil

 ii. Waivable Compulsory License Schemes. In those jurisdictions
in which the right to collect royalties through any statutory or
compulsory licensing scheme can be waived, the Licensor
reserves the exclusive right to collect such royalties for any
exercise by You of the rights granted under this License if Your
exercise of such rights is for a purpose or use which is otherwise
than noncommercial as permitted under Section 4(c) and
otherwise waives the right to collect royalties through any
statutory or compulsory licensing scheme; and,
iii. Voluntary License Schemes. The Licensor reserves the right
to collect royalties, whether individually or, in the event that the
Licensor is a member of a collecting society that administers
voluntary licensing schemes, via that society, from any exercise
by You of the rights granted under this License that is for a
purpose or use which is otherwise than noncommercial as
permitted under Section 4(c).
f. Except as otherwise agreed in writing by the Licensor or as may
be otherwise permitted by applicable law, if You Reproduce,
Distribute or Publicly Perform the Work either by itself or as part of
any Adaptations or Collections, You must not distort, mutilate,
modify or take other derogatory action in relation to the Work
which would be prejudicial to the Original Author's honor or
reputation. Licensor agrees that in those jurisdictions (e.g. Japan),
in which any exercise of the right granted in Section 3(b) of this
License (the right to make Adaptations) would be deemed to be a
distortion, mutilation, modification or other derogatory action
prejudicial to the Original Author's honor and reputation, the
Licensor will waive or not assert, as appropriate, this Section, to
the fullest extent permitted by the applicable national law, to
enable You to reasonably exercise Your right under Section 3(b) of
this License (right to make Adaptations) but not otherwise.
5. Representations, Warranties and Disclaimer
UNLESS OTHERWISE MUTUALLY AGREED TO BY THE PARTIES IN
WRITING AND TO THE FULLEST EXTENT PERMITTED BY APPLICABLE
LAW, LICENSOR OFFERS THE WORK AS-IS AND MAKES NO
REPRESENTATIONS OR WARRANTIES OF ANY KIND CONCERNING THE
WORK, EXPRESS, IMPLIED, STATUTORY OR OTHERWISE, INCLUDING,
WITHOUT LIMITATION, WARRANTIES OF TITLE, MERCHANTABILITY,
FITNESS FOR A PARTICULAR PURPOSE, NONINFRINGEMENT, OR THE
ABSENCE OF LATENT OR OTHER DEFECTS, ACCURACY, OR THE
PRESENCE OF ABSENCE OF ERRORS, WHETHER OR NOT
DISCOVERABLE. SOME JURISDICTIONS DO NOT ALLOW THE
EXCLUSION OF IMPLIED WARRANTIES, SO THIS EXCLUSION MAY
NOT APPLY TO YOU.

Autodesk PowerMill Robot Training Manual 99

 6. Limitation on Liability. EXCEPT TO THE EXTENT REQUIRED BY
APPLICABLE LAW, IN NO EVENT WILL LICENSOR BE LIABLE TO YOU
ON ANY LEGAL THEORY FOR ANY SPECIAL, INCIDENTAL,
CONSEQUENTIAL, PUNITIVE OR EXEMPLARY DAMAGES ARISING OUT
OF THIS LICENSE OR THE USE OF THE WORK, EVEN IF LICENSOR
HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
7. Termination
a. This License and the rights granted hereunder will terminate
automatically upon any breach by You of the terms of this License.
Individuals or entities who have received Adaptations or Collections
from You under this License, however, will not have their licenses
terminated provided such individuals or entities remain in full
compliance with those licenses. Sections 1, 2, 5, 6, 7, and 8 will
survive any termination of this License.
b. Subject to the above terms and conditions, the license granted
here is perpetual (for the duration of the applicable copyright in the
Work). Notwithstanding the above, Licensor reserves the right to
release the Work under different license terms or to stop
distributing the Work at any time; provided, however that any such
election will not serve to withdraw this License (or any other
license that has been, or is required to be, granted under the terms
of this License), and this License will continue in full force and
effect unless terminated as stated above.
8. Miscellaneous
a. Each time You Distribute or Publicly Perform the Work or a
Collection, the Licensor offers to the recipient a license to the Work
on the same terms and conditions as the license granted to You
under this License.
b. Each time You Distribute or Publicly Perform an Adaptation,
Licensor offers to the recipient a license to the original Work on the
same terms and conditions as the license granted to You under this
License.
c. If any provision of this License is invalid or unenforceable under
applicable law, it shall not affect the validity or enforceability of the
remainder of the terms of this License, and without further action
by the parties to this agreement, such provision shall be reformed
to the minimum extent necessary to make such provision valid and
enforceable.
d. No term or provision of this License shall be deemed waived and
no breach consented to unless such waiver or consent shall be in
writing and signed by the party to be charged with such waiver or
consent.

100 Robot Training Manual Autodesk PowerMil

 e. This License constitutes the entire agreement between the
parties with respect to the Work licensed here. There are no
understandings, agreements or representations with respect to the
Work not specified here. Licensor shall not be bound by any
additional provisions that may appear in any communication from
You. This License may not be modified without the mutual written
agreement of the Licensor and You.
f. The rights granted under, and the subject matter referenced, in
this License were drafted utilizing the terminology of the Berne
Convention for the Protection of Literary and Artistic Works (as
amended on September 28, 1979), the Rome Convention of 1961,
the WIPO Copyright Treaty of 1996, the WIPO Performances and
Phonograms Treaty of 1996 and the Universal Copyright
Convention (as revised on July 24, 1971). These rights and subject
matter take effect in the relevant jurisdiction in which the License
terms are sought to be enforced according to the corresponding
provisions of the implementation of those treaty provisions in the
applicable national law. If the standard suite of rights granted
under applicable copyright law includes additional rights not
granted under this License, such additional rights are deemed to be
included in the License; this License is not intended to restrict the
license of any rights under applicable law.

Creative Commons Notice

Creative Commons is not a party to this License, and makes no
warranty whatsoever in connection with the Work. Creative Commons
will not be liable to You or any party on any legal theory for any
damages whatsoever, including without limitation any general,
special, incidental or consequential damages arising in connection to
this license. Notwithstanding the foregoing two (2) sentences, if
Creative Commons has expressly identified itself as the Licensor
hereunder, it shall have all rights and obligations of Licensor.
Except for the limited purpose of indicating to the public that the Work
is licensed under the CCPL, Creative Commons does not authorize the
use by either party of the trademark "Creative Commons" or any
related trademark or logo of Creative Commons without the prior
written consent of Creative Commons. Any permitted use will be in
compliance with Creative Commons' then-current trademark usage
guidelines, as may be published on its website or otherwise made
available upon request from time to time. For the avoidance of doubt,
this trademark restriction does not form part of this License.
Creative Commons may be contacted at http://creativecommons.org/.
Certain materials included in this publication are reprinted with the
permission of the copyright holder.

Autodesk PowerMill Robot Training Manual 101

 Creative Commons FAQ
Autodesk's Creative Commons FAQ can be viewed online at
https://knowledge.autodesk.com/customer-service/share-the-
knowledge, and is reproduced here for offline users.
Creative Commons is a simple, open licensing model which allows
individuals to freely modify, remix, and share digital content created
for learning and support.
Borrow from the Autodesk Learning, Support and Video libraries to
build a new learning experience for anyone with any particular need
or interest. It’s out there. You can use it. It’s yours.
In collaboration with Creative Commons, Autodesk invites you to
share your knowledge with the rest of the world, inspiring others to
learn, achieve goals, and ignite creativity.

What is Creative Commons?

Creative Commons (CC) is a nonprofit organization that offers a
simple licensing model that frees digital content to enable anyone to
modify, remix, and share creative works.

How do I know if Autodesk learning content and Autodesk University

content is available under Creative Commons?
All Autodesk learning content and Autodesk University content
released under Creative Commons is explicitly marked with a Creative
Commons icon specifying what you can and cannot do. Always follow
the terms of the stated license.

What Autodesk learning content is currently available under Creative

Commons?
Over time, Autodesk will release more and more learning content
under the Creative Commons licenses.
Currently available learning content:
▪ Autodesk online help-Online help for many Autodesk products,
including its embedded media such as images and help movies.

▪ Autodesk Learning Videos-A range of video-based learning content,

including the video tutorials on the Autodesk YouTube™ Learning
Channels and their associated iTunes® podcasts.

▪ Autodesk downloadable materials-Downloadable 3D assets, digital

footage, and other files you can use to follow along on your own
time.

Is Autodesk learning and support content copyrighted?

102 Robot Training Manual Autodesk PowerMil

 Yes. Creative Commons licensing does not replace copyright.
Copyright remains with Autodesk or its suppliers, as applicable. But it
makes the terms of use much more flexible.

What do the Autodesk Creative Commons licenses allow?

Autodesk makes some of its learning and support content available
under two distinct Creative Commons licenses. The learning content is
clearly marked with the applicable Creative Commons license. You
must comply with the following conditions:
▪ Attribution-NonCommercial-ShareAlike (CC BY-NC-SA) This license
lets you copy, distribute, display, remix, tweak, and build upon our
work noncommercially, as long as you credit Autodesk and license
your new creations under the identical terms. Terms of this license
can be viewed online at https://creativecommons.org/licenses/by-
nc-sa/3.0/us/

▪ Attribution-NonCommercial-No Derivative Works (CC BY-NC-ND) This

license lets you copy, distribute, and display only verbatim copies
of our work as long as you credit us, but you cannot alter the
learning content in any way or use it commercially. Terms of this
license can be viewed online at
https://creativecommons.org/licenses/by-nc-
nd/3.0/us/deed.en_US

▪ Special permissions on content marked as No Derivative Works For

video-based learning content marked as No Derivative Works (ND),
Autodesk grants you special permission to make modifications but
only for the purpose of translating the video content into another
language.
These conditions can be modified only by explicit permission of
Autodesk, Inc. Send requests for modifications outside of these
license terms to [email protected].

Can I get special permission to do something different with the learning

content?
Unless otherwise stated, our Creative Commons conditions can be
modified only by explicit permission of Autodesk, Inc. If you have any
questions or requests for modifications outside of these license terms,
email us at [email protected].

How do I attribute Autodesk learning content?

Autodesk PowerMill Robot Training Manual 103

 You must explicitly credit Autodesk, Inc., as the original source of the
materials. This is a standard requirement of the Attribution (BY) term
in all Creative Commons licenses. In some cases, such as for the
Autodesk video learning content, we specify exactly how we would
like to be attributed.
This is usually described on the video's end-plate. For the most part
providing the title of the work, the URL where the work is hosted, and
a credit to Autodesk, Inc., is quite acceptable. Also, remember to
keep intact any copyright notice associated with the work. This may
sound like a lot of information, but there is flexibility in the way you
present it.
Here are some examples:
"This document contains content adapted from the Autodesk® Maya®
Help, available under a Creative Commons Attribution-
NonCommercial-Share Alike license. Copyright © Autodesk, Inc."
"This is a Finnish translation of a video created by the Autodesk Maya
Learning Channel @ www.youtube.com/mayahowtos. Copyright ©
Autodesk, Inc."
"Special thanks to the Autodesk® 3ds Max® Learning Channel @
www.youtube.com/3dsmaxhowtos. Copyright © Autodesk, Inc."

Do I follow YouTube's standard license or Autodesk's Creative Commons

license?
The videos of the Autodesk Learning Channels on YouTube are
uploaded under YouTube's standard license policy. Nonetheless, these
videos are released by Autodesk as Creative Commons Attribution-
NonCommercial-No Derivative Works (CC BY-NC-ND) and are marked
as such.
You are free to use our video learning content according to the
Creative Commons license under which they are released.

Where can I easily download Autodesk learning videos?

Most of the Autodesk Learning Channels have an associated iTunes
podcast from where you can download the same videos and watch
them offline. When translating Autodesk learning videos, we
recommend downloading the videos from the iTunes podcasts.

Can I translate Autodesk learning videos?

104 Robot Training Manual Autodesk PowerMil

 Yes. Even though our learning videos are licensed as No Derivative
Works (ND), we grant everyone permission to translate the audio and
subtitles into other languages. In fact, if you want to recapture the
video tutorial as-is but show the user interface in another language,
you are free to do so. Be sure to give proper attribution as indicated
on the video's Creative Commons end-plate. This special permission
only applies to translation projects. Requests for modifications outside
of these license terms can be directed to
[email protected].

How do I let others know that I have translated Autodesk learning content
into another language?
Autodesk is happy to see its learning content translated into as many
different languages as possible. If you translate our videos or any of
our learning content into other languages, let us know. We can help
promote your contributions to our growing multilingual community. In
fact, we encourage you to find creative ways to share our learning
content with your friends, family, students, colleagues, and
communities around the world. Contact us at
[email protected].

I have translated Autodesk learning videos into other languages. Can I

upload them to my own YouTube channel?
Yes, please do and let us know where to find them so that we can
help promote your contributions to our growing multilingual Autodesk
community. Contact us at [email protected].

Can I repost or republish Autodesk learning content on my site or blog?

Yes, you can make Autodesk learning material available on your site
or blog as long as you follow the terms of the Creative Commons
license under which the learning content is released. If you are simply
referencing the learning content as-is, then we recommend that you
link to it or embed it from where it is hosted by Autodesk. That way
the content will always be fresh. If you have translated or remixed our
learning content, then by all means you can host it yourself. Let us
know about it, and we can help promote your contributions to our
global learning community. Contact us at
[email protected].

Can I show Autodesk learning content during my conference?

Autodesk PowerMill Robot Training Manual 105

 Yes, as long as it's within the scope of a noncommercial event, and as
long as you comply with the terms of the Creative Commons license
outlined above. In particular, the videos must be shown unedited with
the exception of modifications for the purpose of translation. If you
wish to use Autodesk learning content in a commercial context,
contact us with a request for permission at
[email protected].

Can I use Autodesk learning content in my classroom?

Yes, as long as you comply with the terms of the Creative Commons
license under which the learning material is released. Many teachers
use Autodesk learning content to stimulate discussions with students
or to complement course materials, and we encourage you to do so as
well.

106 Robot Training Manual Autodesk PowerMil

 Can I re-edit and remix Autodesk video learning content?
No, but for one exception. Our Creative Commons BY-NC-ND license
clearly states that "derivative works" of any kind (edits, cuts, remixes,
mashups, and so on) are not allowed without explicit permission from
Autodesk. This is essential for preserving the integrity of our
instructors' ideas. However, we do give you permission to modify our
videos for the purpose of translating them into other languages.

Can I re-edit and remix Autodesk downloadable 3D assets and footage?

Yes. The Autodesk Learning Channels on YouTube provide
downloadable 3D assets, footage, and other files for you to follow
along with the video tutorials on your own time. This downloadable
material is made available under a Creative Commons Attribution-
NonCommercial-ShareAlike (CC BY-NC-SA) license. You can download
these materials and experiment with them, but your remixes must
give us credit as the original source of the content and be shared
under the identical license terms.

Can I use content from Autodesk online help to create new materials for a
specific audience?
Yes, if you want to help a specific audience learn how to optimize the
use of their Autodesk software, there is no need to start from scratch.
You can use, remix, or enrich the relevant help content and include it
in your book, instructions, examples, or workflows you create, then
Share-Alike with the community. Always be sure to comply with the
terms of the Creative Commons license under which the learning
content is released.

What are the best practices for marking content with Creative Commons
Licenses?
When reusing a CC-licensed work (by sharing the original or a
derivative based on the original), it is important to keep intact any
copyright notice associated with the work, including the Creative
Commons license being used. Make sure you abide by the license
conditions provided by the licensor, in this case Autodesk, Inc.

Autodesk PowerMill Robot Training Manual 107

 Trademarks
The following are registered trademarks or trademarks of Autodesk,
Inc., and/or its subsidiaries and/or affiliates in the USA and other
countries: 123D, 3ds Max, ADSK, Alias, ArtCAM, ATC, AutoCAD LT,
AutoCAD, Autodesk, the Autodesk logo, Autodesk 123D, Autodesk
Alias, Autodesk Forge, Autodesk Fusion, Autodesk Inventor,
AutoSnap, BIM 360, Buzzsaw, CADmep, CAMduct, Civil 3D,
Configurator 360, Dancing Baby (image), DWF, DWG, DWG
(design/logo), DWG Extreme, DWG TrueConvert, DWG TrueView,
DWGX, DXF, Eagle, ESTmep, FBX, FeatureCAM, Flame, FormIt 360,
Fusion 360, The Future of Making Things, Glue, Green Building Studio,
InfraWorks, Instructables, Instructables (stylized robot design/logo),
Inventor, Inventor HSM, Inventor LT, Make Anything, Maya, Maya LT,
Moldflow, MotionBuilder, Mudbox, Navisworks, Netfabb, Opticore,
PartMaker, Pier 9, PowerInspect, PowerMill, PowerShape, Publisher
360, RasterDWG, RealDWG, ReCap, ReCap 360, Remake, Revit LT,
Revit, Scaleform, Shotgun, Showcase, Showcase 360, SketchBook,
Softimage, Tinkercad, TrustedDWG, VRED.
All other brand names, product names or trademarks belong to their
respective holders.

Disclaimer
THIS PUBLICATION AND THE INFORMATION CONTAINED HEREIN IS
MADE AVAILABLE BY AUTODESK, INC. "AS IS." AUTODESK, INC.
DISCLAIMS ALL WARRANTIES, EITHER EXPRESS OR IMPLIED,
INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE
REGARDING THESE MATERIALS.

Except where otherwise noted, this work is licensed

under a Creative Commons Attribution-NonCommercial-ShareAlike 3.0
Unported License. Please see the Autodesk Creative Commons FAQ for
more information.

108 Robot Training Manual Autodesk PowerMil