( consult factory before using )( consult factory before using )( consult factory before using )

1.2 H1 nameplate 2.2 Founction card configuration table

Function card
NO.5 Function·Parameter Table
H10001 H10002 H10003 H10004 H10005 H10006 H10007 H10008 H10009 H10010 H10011 H10012
H1 00 S2 0007 B T 0 Physical characteristics

Digital input 4 3 4 8 2 2 3 2 2 4 4 3 Function Function Description( setting range) Factory default

code
0:domestic 1~9:overseas Digital output 4 4 1:parameter initialization, initialize parameters
P0.09 Parameter operation except PI.XX, in normal condition, use mode 1initialization; 0
T: with STO X:without STO Relay output 1 3 1 1 1 1 1 1 1 1 1 2. initialize all parameters

Analog input 1 1 2 1 1 1 1 1 0:keypad

H1 Series Inverter B: built-in brake unit X: without brake unit
Power:kW
Analog output 2 1 1
P0.10 Setting(frequency) reference F1
2:AI1
P1.63
1:multi-speed 0:digital setting;
1:potentiometer setting;
0

Pulse input 1 3:AI2

USER MANUAL Pulse output 1

P0.11 Setting(frequency) reference F2 5:communication 0

S/T:single phase/three phase 2/4:220/380V

Encoder input 1 0:F1 P0.10 P0.12
1:F2
customized model 2:F1+F2 keypad 0
Modbus 1 1 1 1 1 1 1 1 1 1 1 1 3:F1-F2 multi-speed 1
F1
F2
0
1
AI1
F1
4:F1*F2/100 2 setting value 1 F1+F2 2
Series (H1 series) Profibus 1 5:maximum value(F1,F2) AI2 3
communication 5
F1-F2
P10.90 F1*F2/100
3
6:minimum vlue(F1,F2) 4
maximum value (F1,F2)5
7:average value(F1,F2) keypad 0
Canbus 1 8:PID(F1,F2) multi-speed 1 F2
minimum value(F1,F2)6

1.3 H1 series specifications and models AI1

AI2
2
3 setting value 2
average value(F1,F2) 7

P10.91 PID(F1,F2) 8
Bluetooth 1 communication
5

Power P0.11
Base.No Models Input voltage
( kw )
Output current(A) Adaptive motor(KW) GPRS 1 * principle interpretation:
set 0 choose F1 channel setting value;

H100S20007BX0 1 phase 220V 0.75 5.0 0.75

STO 1 P0.12 setting relation selection
set 1 choose F2 channel setting value; 0
set 2 choose the sum of F1 and F2 channel setting value;
F1 set 3 choose the difference of F1 and F2 channel setting value;
H100S20015BX0 1 phase 220V 1.5 7.0 1.5 Typical application
set 4 choose the product of F1 ans F2 channel setting value
divide 100;
F2 H100T20022BX0 3 phase 220V 2.2 12.5 2.2 set 5 choose larger value of F1 and F2;
se 6 choose smaller value of F1 and F2;
F3 H100T20037BX0 3 phase 220V 3.7 15.2 3.7 set 7 choose average value of F1 and F2;
NO.3 Product Dimension set 8 choose PID control(F1 is setting, F2 is feedback).
H100T40007BX0 3 phase 380V 0.75 3.0 0.75
F1 H100T40015BX0 3 phase 380V 1.5 4.5 1.5
W
H100T40022BX0 3 phase 380V 2.2 5.6 2.2 A d D
F2 H100T40040BX0 3 phase 380V 4.0 10.5 4.0
H100T40055BX0 3 phase 380V 5.5 14 5.5 ﹣99999.000~99999.000
F3 * principle interpretation:
H100T40075BX0 3 phase 380V 7.5 19 7.5 limit setting value range.The unit of setting source is %, the
P0.13 maximum setting value maximum setting value(P0.13) stands for 100%, take 50.000
H100T40110BX0 3 phase 380V 11 26 11 mximum setting value as standard.
F4
H100T40150BX0 3 phase 380V 15 33 15

H
B
H100T40185BX0 3 phase 380V 18.5 40 18.5 0.000Hz~1000.000Hz
F5 motor output frequency
P0.14 upper limit interpretation:motor operation frequency upper limit 55.000Hz
H100T40220BX0 3 phase 380V 22 46 22
S4 S3 S2 valid multi-speed
0 0 0 multi - speed 0
0~11111111
0 0 1 multi - speed 1
units:S1
0 1 0 multi - speed 2
tens: S2
0 1 1 multi - speed 3
hundreds’ digit: S3
thousands'digit:S4 1 0 0 multi - speed 4
1 0 1 multi - speed 5
NO.2 Main circuit and function card ...
H1 series P0.15 multi-speed source 1 1 0 multi - speed 6
1 1 1 multi - speed 7
Dimensions( mm)
Framework * P0.15:multi-speed source,select to corresponding external
W(Width) H(Height) D(Depth) A B d terminal, multi-speed refer to P0.16-P0.23. 0
11KW~22KW with P- terminal
* eg:selectS2、S3、S4 as valid external terminal to control
Braking resistor F1 85 170 124 67.3 158 5 multi-speed

Power supply input

F2 97 194 133 85 184 5 set P0.15=1110, detailed 8 segment corresponding relationship as
above table
P+ PB P-
F3 126 237 147 112 223 6
R R/L1 U
NO.1 Product introduction M
F4 168 298 160 154 283 6 P0.16 multi-speed 0 0.000%
S S/L2 V
Main circuit ~ F5 198 355 177 183 338 6 P0.17 multi-speed 1 0.000%
T T/L3 W P0.18 multi-speed 2 ﹣1000.000%~1000.000% 0.000%
function: multi-speed setting, corresponding to P0.13
1.1 Technical Features single 220V input connect with P0.19 multi-speed 3 maximum setting percentage 0.000%
R/L1 and S/L2 NO.4 Keypad description P0.20 multi-speed 4 0.000%
Items Description P0.21 multi-speed 5 0.000%
Rated 3ph: 380V~440V , 50Hz/60Hz P0.22 multi-speed 6 0.000%
voltage
1ph: 200V~240V , 50Hz/60Hz 4.1 Keypad appearance and keypad explanation
input

/frequency digital output P0.23 multi-speed 7 0.000%

digitl input
Allowed 3ph: 320V~460V ; 1ph: 180V~260V; relay output Item Structure Function description 0.000s~3600.000s
voltage voltage Imbalance rate: <3% ; frequency: ±5% * principle interpretation:
H10001
Voltage 0~ rated input voltage 1 Display as figure, acceleration time refer to the time from 0HZ
P0.24 accelerate to P0.13 maximum setting value
output

acceleration time
RUN ALM

Frequency 0Hz~1000Hz Analog input function analog output REV 2 PRG

Program/exit
output frequency
Overload capacity 150% rated current 60s，180% rated current 2s card REM M

Status diaplay interface work as status switch P0.13

3 key;other interface work as left shift key *S
Control mode V/F、SVC
PRG M
Modulation Mode SVPMW
Motor type
asynchronous motor, synchronour motor, pulse input pulse output ENTER N 4 N Reserved key
P0.25
single phase motor ( consult factory before using ) deceleration time
RUN STOP
Start torque 1Hz/150% RESET time
5
control performance

RUN RUN
acceleration time deceleration time
Speed range 1:100( SVC )
digital setting: maximum frequency±0.01%; standard 6 Potentiometer: refer to parameter P1.63 ﹣1000.000~1000.000
Frequency encoder input P0.26 Jog frequency
function: set jog frequency, jog command refer to P0.33 10.000%
accuracy anolog setting: maximum frequency±1%; Modbus
7 In the mode of program, work as value change
digital setting: 0.1Hz; 0:invalid
Frequency key; otherwise, UP/DOWN key, refer to P0.30 start command source 1:keypad 1
resolution anolog setting: maximum frequency±1% ; Profibus 8 parameter P1.63, P2.03, P2.04 2:communication
Acceleration/ STO Canbus 3:S1
deceleration curve line/ S-curve bluetooth、 4:S2
(optional)
GPRS 5:S3
Rapid current limit limit current rapidly within the current protection value, to ensure the safety of the equipment (optional) P0.31 reverse start command source 6:S4 0
9 ENTER Enter
None-stop when
instantaneous power off none-stop when instantaneous power off, automatic frequency drop ...
function: select command source(select keypad as command
keypad, terminal, communication Figure 3-1 H1 series keypad source, then reverse start command, reverse command,
Operation

Command source 10 STOP

STOP/RESET
function

RESET
jog command, free stop command, safe stop command,
Set value source
Notice: different function card corresponding to different terminals. Except standard function card, can costomize any type of card. P0.32 reverse command source
pause command all from multi-function key of keypad)
0
digital, analog,multi-speed,communication
Reset parameters when using different function cards. An AC drive only can use one function card.
11 M
Customization key

PID support main setting+PID

Warning: Do not use function card when power is on! 4.2 Indicator light description 4.3 Display item description P0.33 Jog command source 1
Operation

LED display Can display: output frequency,output voltage,output current , Bus voltage ,
panel

display value 1 , display value 2, error, alarm Display code Item description
Indicator light Status Function description
* reverse start command: setting value reversed, and give a

External keypad YES

2.1 Main circuit terminal description light on/ operating output frequency
P0.34 stop command source
start command
0
RUN flickering /decelerating * reverse command: setting value reversed.
over- current protection、over- voltage protection、under- voltage protection、 output current * jog command: jog command. Priority is higher than start
Protection function overheating protection、over- load protection、phase lose protection、earth leakage, Terminal identification Name Function description command, lower than stop command.
etc
REV light on reverse operation
output voltage
Store indoor,away from direct sunlight,no dust,no corrosive gas, no inflammable
Grounding terminal Safety grounding P0.35 free stop command source 0
REM light on remote operation 16 15 14 13 12 11 10 9 8
enviornment gas, no oil mist, no vapour, no drip and no salinity, etc Connect three phase power supply, single phase power supply DC bus voltage
R/L1、S/L2、T/L3 Main circuit power input terminal S14 S13 S12 S11 S10 S9 S8 S7 S6
Environment

connect to R/L1, S/L2

Altitude derating use abouve 1000M, derating 10% per 1000M ALM light on fault indication 7 6 5 4 3 2 1 0
display value 1(P10.98)
Environment P+、PB
temperature
-10℃~+40℃(environment temperature around 40℃~50℃please derating use) Braking terminal Connect to external braking resistor S5 S4 S3 S2 S1 communication keypad invalid
customization indication, P0.36 reset command source 1
Humidity 5%~95%RH, no condensation M light on display value 2(P10.99)
Two sets or more inverters use a common DC bus default alarm indication
Store
-40℃~+70℃ P+、P- DC bus terminal
temperature ( 11KW~22KW has P- terminal ) current alarm
Vibration <5.9M/S (0.6g)
U、V、W output terminl Connect to three phase motor current fault
Function Function Function Function Function
Description(setting range) Factory default Function Description(setting range) Factory default Function Description(setting range) Factory default Function Description(setting range) Factory default
code code code code

0:positive logic ﹣999999.000~999999.000 0:no check

1:negative logic ⊙function: analog input AI1 setting 1:even check
2:rising edge P0.41 AI1 low side voltage(current) *AI1 low side voltage(current): set the lowest voltage(current) 0.000V(mA) 0:start frequency operation P1.43 odd-even check 2:odd check 0
3:falling edge of input signal. 1:speed start ⊙function: Communication port configuration
function: select external terminal trigger type 2:DC injection
*AI1 high side voltage(current): set the highest voltage(current)
* principle interpretation: of input signal. * principle interpretation: 8~9
0:positive logic, high level is valid status, low level is *AI1 low side setting: set corresponging value of low side P0.60 startup function 0:no frequency output startup mode, meet to P0.61 startup time 0 P1.44 data bits ⊙function: Communication port configuration 8Bits
invalid status; voltage(current). setting, P0.62 start frequency start to startup operation.
1: negative logic, high level is invalid status, low level is P0.42 AI1 high side voltage(current) *AI1 high side setting: set corresponding value of high side 10.000V(mA) 1:speed start, search rotating motor speed, smooth start
without impact from search speed. 0.0~2.0
valid status; voltage(current). P1.45 stop bits
⊙function: Communication port configuration
1.0Bit
2:DC injection, inverter startup by “DC injection before startup”
2: rising edge, rising edge is valid; mode.
3: falling edge, falling edge is valid.
range setting

*two-line mode 1: AI1 high side setting

the mode is most commonly used two-line mode, enable and P0.43 AI1 low side setting P0.44 0.000% 0.000S~60000.000S 0~123
units:0:remain decimal place,1:decimal place change to 2
direction combined, K1 and K2 control forward/reverse of
AI1 terminal setting P3.04 P0.61 startup time principle interpretation: when system startup,setting start 0.000S places, 2:decimal place change to 1 place, 3:no decimal place;
motor 0:voltage input function work within setting start time.
1:current input
tens:0:remain decimal place,1:decimal place change to 1 place,
2:no decimal place;
P0.37 S1 type 0 AI1 low side setting 0.000Hz~100.000Hz
hundreds' digit: 0:remain decimal place,1:no decimal place;
P0.43 * principle interpretation:
principle interpretation: start function finish, if setting frequency
P0.44 AI1 high side setting 100.000% parameter decimal place mode only work to communication,
P0.62 start frequency bigger than start frequency, system start from start frequency; 0.000Hz which change parameter value during communication
0 P0.41 P10.71 P0.42 voltage( current) input if setting frequency smaller than start frequency, system start P1.47 0
parameter decimal place mode transmission.
from setting frequency.
AI1 AI 1terminal input AI1 * P1.47 units aim at parameters with 3 decimal places:
low side voltage( current) high side voltage( current) 0:remain decimal place,1:decimal place change to 2 places,
K1 2:decimal place change to 1, 3:no decimal place.
S1(forward) operation
K1 K2
command
* P1.47 tens aim to parameters with 2 decimal places;
0:always 0 1:always 10V/20mA 0.000%~200.000% 0:remain decimal place,1:decimal place change to 1 place,
K2
OFF OFF stop 2:output frequency 3:motor current ⊙function: set magnitude of DC injection current. 2:no decimal place.
S2(reverse) 4:output voltage 5:motor torque (set P0.60=2 as DC injection) * P1.47 hundreds' digit aim to parameters with 1 place:
OFF ON reverse
6:output power 7:setting frequency P0.63 DC injection current * principle interpretation: 100.000% 0:remain decimal place,1:no decimal place.
ON OFF forward 100~9999:high leverl parameter start mode is DC injection, need to set magnitude of DC
COM
* * principal interpretation: braking current, 100% corresponding to inverter rated current.
ON ON stop
AO1 signal source function description as below:
parameter no. setting vlue description
0:keyboard digital setting; 1:keyboard potentiometer setting;
P0 . 30 3 start command source is S1
units:0:free stop;1:DC braking; * principle interpretation:
P0 . 31 4 reverse start command source is S2
P0.45 AO1 signal source setting value function description 2 tens:1:accurate stop P1.63 keyboard setting source select keyboard setting value source, digit setting( P2.92) or 1
* principle interpretation: keyboard potentiometer.
P0 . 37 0 S1 type is positive logic 0 always 0 analog AO1 output always 0
during stop process, stop function starts work when output
P0 . 38 0 S2 type is negative logic 1 always 10V/ 20mA analog AO1 output always 1 frequency smaller than stop frequency.
2 output frequency analog AO1 output is output frequency
P0.64 stop function accurate stop: stop at any speed motor rotation turns are 0
same, realize consistent repeatability of stop position. To get P2.03 (UP) command source units:keyboard; 0
* two-line mode 2: 3 motor current analog AO1 output is motor current
the best efficiency, deceleration time not to trigger over tens: communication;
enable and direction seperated, in this mode K1 is enable 4 output voltage analog AO1 output is output voltage pressure and over loss rate prevention function as long as hundreds' digit: S1;
terminal, direction is controlled by K2. 5 motor torque analog AO1 output is motor torque possible. thousands' digit: S2;
6 output power analog AO1 output is output power P2.04 (DOWN)command source … 0
7 setting frequency analog AO1 output is setting frequency
0.000Hz~1000.000Hz
K1 S1(operation) K1 K2
operation
command
100~9999 high level parameter P0.65 stop frequency interpretation refer to 0.64 0.000Hz P10.61 history fault no.1 - 0
OFF OFF stop
K2
S2(forward/reverse) ﹣999999.000~999999.000 0.000%~150.000% P10.62 history fault no.2 - 0
OFF ON stop * AO1 low side setting: set AO1 source minimum value. P0.66 DC braking current set DC braking current. 100.000%
ON OFF forward P0.46 AO1 low side setting * AO1 high side setting: set AO1 source maximum value. 0.000 P10.63 history fault no.3 - 0
COM * AO1 low side voltage(current): set the lowest voltage(current) 0.000s~1000.000s
ON ON reverse of output signal. P0.67 DC braking time set DC braking time. 0.000s P11.10 output frequency upon
- 0.0Hz
* AO1 high side voltage(current): set the highest voltage(current) current fault
output current upon
parameter no. setting value description of output signal.
0:invalid
P11.11 current fault
- 0.00A
P0 . 30 3 start command source is S1
P0.47 AO1 high side setting 50.000 P0.68 braking resistor mode 1:valid 1 P11.12 bus voltage upon current
- 0.0V
P0 . 32 4 reverse command source is S2 function:braking resistor braking mode parameter set fault
P0.38 S2 type P0 . 37 0 S1 type is positive logic 0 voltage( current) P11.13 inverter temperature upon
- 0℃
output current fault
P0 . 38 0 S2 type is positive logic F(Hz)
operating (P10.15 Bit5)
P0.49
AO1 high side voltage
( current)
running (P10.15 Bit2) P11.14 S terminal status upon
current fault
- 0
* three line mode 1: P0.48 AO1 low side voltage(current) 0.000V(mA) stopping (P10.15 Bit1)
this mode define SB2 as enable terminal, operation command P10.75 P3.60
0:voltage output
P11.15 Y terminal status upon
current fault
- 0
AO1 terminal setting
is generated by SB1 or SB3, control operation direction at the 1:current output stop already
start function P5.26 P0.67 cumulative running time
same time. (P10.15 Bit3) (P10.15 Bit6) P11.16 upon current fault - 0h
inverter is running and SB2 is in closed state, terminal SB1 P0.48
AO1 low side voltage
or SB3 generates a rising edge signal to control inverter ( current) P0.65
operation and direction; disconnection SB2 to stop inverter.
P0.49 AO1 high side voltage(current) 10.000V(mA) P0.62
0 P0.46 P0.45 P0.47 range setting P0.64
AO1 AO1 AO1
low side setting signal source high side setting P0.60 t

0.000%~10.000% start
SB1
S1(forward)
P0.50 PID proportional gain Determine the adjustment intensity of the whole PID regulator,
bigger proportional gain is, bigger adjustment intensity is.
0.010%
t
NO.6 Fault code
system control
SB2 operation
S2(enable) SB1 SB2 SB3
command
0.001S~9999.000S
0 stop Determine PID regulator to the integral speed adjustment of 0:VF
SB3
S3(reverse)
P0.51 PID integral gain the diviation of PID feedback quantity and given quantity. 10.000S P0.70 control mode 1:vector control 1 1 Fault Code Protection function Description
1 forward function:select motor control algorithm
smaller integral gain is, greater adjustment intensity is.
COM
1 reverse 1 protection function inverter components fault or software fault
2kHz~16kHz
parameter no. setting value description -1000.000~1000.000
P0.71 carrier frequency ⊙function: set carrier frequency * kHz
P0 . 30 3 start command source is S1 PID adjust the output maximum value, if higher than maximum 4 ground fault Abnormal resistance to ground, cause electric leakage
P0.52 PID output upper limit value, then output PID output upper limit, relative to P0.11 100.000% 0.000kW~100000.000kW
P0 . 31 5 reverse start command source is S3 maximum setting value percentage. P0.72 motor power * kW
⊙function: set motor parameters
P0 . 34 4 stop command source is S2 5 short circuit to ground short circuit to ground
P0 . 37 2 S1 type is rising edge 0V~1000V
P0 . 38 1 S2 type is negative logic -1000.000~1000.000 P0.73 motor voltage ⊙function: set motor parameters *V
6 inverter cut off output when inverter output current is 250% larger than inverter
P0 . 39 2 S3 type is rising edge PID adjust the output minimum value, if lower than minimun output short circuit
value, then output PID output lower limit, relative to P0.11 rated current.
P0.53 PID output lower limit 0.000% 1Hz~3000Hz
* three line mode 2: maximum setting value percentage. P0.74 motor frequency ⊙function: set motor parameters * Hz
this mode define SB2 as enable terminal, operation command inverter cut off output when inverter output current is 200% larger than inverter
is generated by SB1, direction command is controlled by K.
7 output over current
0.00A~1000.00A
inverter is running and SB2 is in closed state, terminal B1 0.001~99999.000 P0.75 motor current
⊙function: set motor parameters
*A rated current.
set according to actul feedback valu, if lower than feedback 100.000
generates a rising edge signal to control inverter operation, P0.54 PID range
value, then PID invalid. inverter cut off output if main circuit DC voltage is higher than 400V(220V motor
K control operation direction; disconnection SB2 to stop 10rpm~65535rpm 8 DC bus over voltage
inverter.
P0.76 motor speed ⊙function: set motor parameters * RPM type) or 800V(380V motor type) when motor decelerates.

P0.39 S3 type 0
0.000~500.000 P0.78 VF curve-F1 0Hz~3000Hz 50Hz
P0.55 PID dormancy frequency set dormancy accurate frequency, relative to P0.11 maximum 0.000% * principle interpretation: 9 DC bus low voltage input voltage decrease, inverter cut off output if main circuit DC voltage too low.
setting value percentage. P0.79 VF curve-F2 50Hz
set V/F curve under V/F control mode. When vector control
SB1 1 is adopted, set the corresponding frequency points of V/F
S1(operation) P0.80 VF curve-F3
curve to adjust control characteristics of the corresponding
50Hz 10 inverter over heat inverter cut off output if cooling fin is over heat.
0.000~3600.000
SB2
S2(enable)
operation P0.56 PID enter dormancy time inverter reach enter dormancy time and meet to dormancy time, 0.000s P0.81 VF curve-F4
control points.
50Hz
SB1 SB2 K command enter dormancy. 11 self-learning failure self-learning parameter wrong or motor abnormal.
K
0 stop P0.82 VF curve-V0 0V
S3(forward/reverse)
1 OFF forward 0.000~100.000 0V~10000V
P0.57 PID wakeup deviation percentage based on setting value. 0.000% P0.83 VF curve-V1 *V 13 rectifier over heat rectifier module over heat.
COM
1 ON reverse * principle interpretation:
P0.84 VF curve-V2 set V/F curve under V/F control mode. When vector control *V
parameter no. setting value description
0.000~3600.000 1 is adopted, set the corresponding voltage points of V/F curve 14 U phase loss output U phase loss.
P0.58 PID enter wakeup time inverter reach wakeup deviation and meet to wakeup time, 0.000s P0.85 VF curve-V3 to adjust control characteristics of the corresponding control *V
P0 . 30 3 start command source is S1 operation again. points.
P0 . 32 5 reverse command source is S3 P0.86 VF curve-V4 *V 15 V phase loss output V phase loss.
P0 . 34 4 sop command source is S2 0:no dormancy; 1:PID stop;
P0 . 37 2 S1 terminal command type is rising edge 2:decelerate to stop; 3:free stop; voltage
16 W phase loss output W phase loss.
P0 . 38 1 S2 terminal command type is negative logic P0.59 PID dormancy action 4:pause; 5:operate in lowest frequency 0 MAX
P0 . 39 0 S3 terminal command type is positive logic PID enter dormancy according to setting dormancy action.
P0.86 19 no motor connect motor lost connection during operation.

0:always 0 1:always 1 2:stopped 3:running

pressure sensor range:1.6MPa(1MPa=10kg)PIDcontrol parameter 20 input phase loss power input phase loss.
4:fault 5:alarm 6:reversing 64:STO status
parameter setting
100~9999:high level parameter parameter name description
no. value
P0.85
* principal interpretation: P1.63 keypad setting source 0 digital keypad(P2.92)setting

terminal source setting value ≥100( address mode) , PID output T1-PID enter dormancy time
P2.92 setting value 10 PID digital keypad set 10kg 21 inverter over load inverter cut off output when inverter output current exceed inverter rated level
P0.11 feedback value 2 PID analog AI1 feedback
P0.84 (150% 60S).
the address is selected parameter no., actual value is decided P0.56
dormancy status
T<T1 P0.12 setting relationship selection 8 PID enable
by current value of selected parameter no.. PID dormancy action select
terminal source function description as below:
T1
P0.59 P0.44 AI1 high side setting 16
AI1 high side set 16kg
(0~10V corresponding to 0~16kg)
P0.83 22 over torque motor over torque
PID dormancy frequency P0.50 PID proportional gain 0.01% according to field adjustment(turn up PID intensity greater) P0.82
P0.55 P0.51 PID integral gain 10s according to field adjustment(turn down PID intensity greater) 24 motor over heat motor temperature is over heat.
inverter run 0 P0.78 P0.79 P0.80 P0.81 frequency
P0.40 Y1 terminal source 3 time P0.54 PID range 16 PID set feedback range 16kg
setting value function description PID dormancy frwquency set 5Hz
T1-PID enter wakeup time P0.55 PID dormancy frequency 10% 0~247 inverter cut off output when inverter output current exceed motor rated level
0 always 0 Y1 terminal output always 0
PID output
P0.58
(maximum default setting value 50Hz)
P1.41 local address ⊙function: set inverter local address 1 25 motor over load (150% 60S).
T2 inverter startup
P0.56 PID dormancy time 5s PID dormancy time 5s
1 always 1 Y1 terminal output always 1
PIDwakeup accurate position P0.57 PID wakeup deviation 20% PID wakeup deviation 20%
2 stopped in stopped status Y1 terminal output is 1
P0.58 10s
3 running in running status Y1 terminal output is 1
P0.57
P0.59
PID enter wakeup time PID wakeup time10s
0:2400bps 1:4800bps 26 current limit output current exceed setting limit threshold.
time PID dormancy action 2 PID deceleration to stop after dormancy, set 0 if don' t dormancy

4 fault in fault status Y1 terminal output is 1 P1.68 1090

2:9600bps 3:19200bps
displayed value 1 source keyboard display PID setting pressure
5 in alarm status Y1 terminal output is 1 P1.69 displayed value 2 source 1091 keyboard display PID feedback pressure
P1.42 baud rate 4:38400bps 5~10:reserved 3 63 user fault user defined fault(P3.08)
alarm ⊙function: Communication port configuration
6 reversing in reversing status Y1 terminal output is 1 P2.03 (UP)command source 1 (UP) command from keyboard
(DOWN)command
64 STO status in STO status Y1 terminal output is 1 P2.04 source 1 (DOWN)command from keyboard

100~9999 high level parameter