Junos® OS

Routing Protocols Overview

Published

2023-06-13
 ii

Juniper Networks, Inc.

1133 Innovation Way
Sunnyvale, California 94089
USA
408-745-2000
www.juniper.net

Juniper Networks, the Juniper Networks logo, Juniper, and Junos are registered trademarks of Juniper Networks, Inc.
in the United States and other countries. All other trademarks, service marks, registered marks, or registered service
marks are the property of their respective owners.

Juniper Networks assumes no responsibility for any inaccuracies in this document. Juniper Networks reserves the right
to change, modify, transfer, or otherwise revise this publication without notice.

Junos® OS Routing Protocols Overview

Copyright © 2023 Juniper Networks, Inc. All rights reserved.

The information in this document is current as of the date on the title page.

YEAR 2000 NOTICE

Juniper Networks hardware and software products are Year 2000 compliant. Junos OS has no known time-related
limitations through the year 2038. However, the NTP application is known to have some difficulty in the year 2036.

END USER LICENSE AGREEMENT

The Juniper Networks product that is the subject of this technical documentation consists of (or is intended for use
with) Juniper Networks software. Use of such software is subject to the terms and conditions of the End User License
Agreement ("EULA") posted at https://support.juniper.net/support/eula/. By downloading, installing or using such
software, you agree to the terms and conditions of that EULA.
 iii

Table of Contents
About This Guide | v

1 Overview
Understanding IP Routing | 2

Routing Databases Overview | 2

Routing Instances Overview | 7

Route Preferences Overview | 11

Understanding Route Preference Values (Administrative Distance) | 16

Equal-Cost Paths and Load Sharing Overview | 19

Routing Protocol Process Overview | 19

Overview of IPv6 Routing | 21

IPv6 Overview | 21

Understanding IPv6 | 25

Supported IPv6 Standards | 31

IPv6 Support on Devices Running Junos OS | 35

2 Monitoring and Troubleshooting

Monitoring Networks | 40

Example: Tracing Global Routing Protocol Operations | 40

Requirements | 40

Overview | 40

Configuration | 41

Verification | 46

Troubleshooting Network Issues | 47

Working with Problems on Your Network | 47

Isolating a Broken Network Connection | 48

Identifying the Symptoms of a Broken Network Connection | 50

 iv

Isolating the Causes of a Network Problem | 52

Taking Appropriate Action for Resolving the Network Problem | 53

Evaluating the Solution to Check Whether the Network Problem Is Resolved | 55

Knowledge Base | 57

3 Configuration Statements and Operational Commands

Configuration Statements | 59

Operational Commands | 60

show | display rfc5952 | 60

 v

About This Guide

Use this guide to understand IP routing fundamentals, monitor routing protocol operations, and to
troubleshoot basic network issues.
1 PART

Overview

Understanding IP Routing | 2

Overview of IPv6 Routing | 21

 2

CHAPTER 1

Understanding IP Routing

IN THIS CHAPTER

Routing Databases Overview | 2

Routing Instances Overview | 7

Route Preferences Overview | 11

Understanding Route Preference Values (Administrative Distance) | 16

Equal-Cost Paths and Load Sharing Overview | 19

Routing Protocol Process Overview | 19

Routing Databases Overview

IN THIS SECTION

Routing Protocol Databases | 3

Junos OS Routing Tables | 3

Networks and Subnetworks | 4

Forwarding Tables | 5

How the Routing and Forwarding Tables Are Synchronized | 6

NetFlow V9 Support | 7

Routing is the transmission of packets from a source to a destination address. A routing protocol
determines the path by which the packets are forwarded, shares information with immediate neighbor
devices and other devices in the network, and adjusts to changing network conditions.

To use the routing capabilities of a Juniper Networks device, you must understand the fundamentals of
IP routing and the routing protocols that are primarily responsible for the transmission of unicast traffic.
To understand this topic, you need a basic understanding of IP addressing and TCP/IP.
 3

The Junos® operating system (Junos OS) maintains two databases for routing information:

• Routing table—Contains all the routing information learned by all routing protocols.

• Forwarding table—Contains the routes actually used to forward packets through the router.

In addition, the interior gateway protocols (IGPs), IS-IS, and OSPF maintain link-state databases.

This section includes the following topics:

Routing Protocol Databases

Each IGP routing protocol maintains a database of the routing information it has learned from other
routers running the same protocol and uses this information as defined and required by the protocol.
Routing information that is shared within an AS is transmitted by an interior gateway protocol (IGP).

Of the different IGPs, the most common are RIP, OSPF, and IS-IS. IS-IS and OSPF use the routing
information they received to maintain link-state databases, which they use to determine which adjacent
neighbors are operational and to construct network topology maps. IGPs are designed to be fast acting
and light duty. They typically incorporate only a moderate security system, because trusted internal
peers do not require the stringent security measures that untrusted peers require. As a result, you can
usually begin routing within an AS by enabling the IGP on all internal interfaces and performing minimal
additional configuration. You do not need to establish individual adjacencies.

IS-IS and OSPF use the Dijkstra algorithm, and RIP and RIPng use the Bellman-Ford algorithm to
determine the best route or routes (if there are multiple equal-cost routes) to reach each destination and
install these routes into the Junos OS routing table.

Routing information that is shared with a peer AS is transmitted by an exterior gateway protocol (EGP).
The primary EGP in use in almost all networks is the Border Gateway Protocol (BGP). BGP is designed to
be very secure. Individual connections must be explicitly configured on each side of the link. As a result,
although large numbers of connections are difficult to configure and maintain, each connection is secure.

When you configure a protocol on an interface, you must also configure a protocol family on that
interface.

Junos OS Routing Tables

The Junos OS routing table is used by the routing protocol process to maintain its database of routing
information. In this table, the routing protocol process stores statically configured routes, directly
connected interfaces (also called direct routes or interface routes), and all routing information learned
from all routing protocols. The routing protocol process uses this collected routing information to select
the active route to each destination, which is the route that actually is used to forward packets to that
destination. To route traffic from a source host to a destination host, the devices through which the
 4

traffic will pass must learn the path that the packet is to take. Once learned, the information is stored in
routing tables. The routing table maintains a list of all the possible paths from point A to point B.

By default, the Junos OS maintains three routing tables: one for unicast routes, another for multicast
routes, and a third for MPLS. You can configure additional routing tables to support situations where
you need to separate a particular group of routes or where you need greater flexibility in manipulating
routing information. In general, most operations can be performed without resorting to the complexity
of additional routing tables. However, creating additional routing tables has several specific uses,
including importing interface routes into more than one routing table, applying different routing policies
when exporting the same route to different peers, and providing greater flexibility with incongruent
multicast topologies.

Each routing table is identified by a name, which consists of the protocol family followed by a period and
a small, nonnegative integer. The protocol family can be inet (Internet), iso (ISO), or mpls (MPLS). The
following names are reserved for the default routing tables maintained by the Junos OS:

• inet.0—Default IP version 4 (IPv4) unicast routing table

• inet6.0—Default IP version 6 (IPv6) unicast routing table

• instance-name.inet.0—Unicast routing table for a particular routing instance

• inet.1—Multicast forwarding cache

• inet.2—Unicast routes used for multicast reverse path forwarding (RPF) lookup

• inet.3—MPLS routing table for path information

• mpls.0—MPLS routing table for label-switched path (LSP) next hops

NOTE: For clarity, this topic contains general discussions of routing tables as if there were
only one table. However, when it is necessary to distinguish among the routing tables, their
names are explicitly used.

Networks and Subnetworks

Large groups of machines that are interconnected and can communicate with one another form
networks. Typically, networks identify large systems of computers and devices that are owned or
operated by a single entity. Traffic is routed between or through the networks as data is passed from
host to host.

Figure 1 on page 5 shows a simple network of routers.

 5

Figure 1: Simple Network Topology

This simple network provides multiple ways to get from host San Francisco to host Miami. The packet
can follow the path through Denver and Cleveland. Alternatively, the packet can be routed through
Phoenix and directly to Miami. The routing table includes all the possible paths and combinations—an
exhaustive list of all the ways to get from the source to the destination.

The routing table must include every possible path from a source to a destination. Routing tables for the
network in Figure 1 on page 5 must include entries for San Francisco-Denver, San Francisco-Cleveland,
San Francisco-Miami, Denver-Cleveland, and so on. As the number of sources and destinations
increases, the routing table quickly becomes large. The unwieldy size of routing tables is the primary
reason for the division of networks into subnetworks.

As networks grow large, the ability to maintain the network and effectively route traffic between hosts
within the network becomes increasingly difficult. To accommodate growth, networks are divided into
subnetworks. Fundamentally, subnetworks behave exactly like networks, except that they are identified
by a more specific network address and subnet mask (destination prefix). Subnetworks have routing
gateways and share routing information in exactly the same way as large networks.

Forwarding Tables

Routing is the transmission of data packets from a source to a destination address. It involves delivering
a message across a network or networks. This process has two primary components: the exchange of
routing information to forward packets accurately from source to destination and the packet-forwarding
procedure.

For packets to be correctly forwarded to the appropriate host address, the host must have a unique
numeric identifier or IP address. The unique IP address of the destination host forms entries in the
routing table. These entries are primarily responsible for determining the path that a packet traverses
when transmitted from source to destination.
 6

The Junos OS installs all active routes from the routing table into the forwarding table. The active routes
are used to forward packets to their destinations.

The Junos OS kernel maintains a master copy of the forwarding table. It copies the forwarding table to
the Packet Forwarding Engine, which is the part of the router responsible for forwarding packets.

If the routing table is a list of all the possible paths a packet can take, the forwarding table is a list of only
the best routes to a particular destination. The best path is determined according to the particular
routing protocol being used, but generally the number of hops between the source and destination
determines the best possible route.

In the network shown in Figure 1 on page 5, because the path with the fewest number of hops from San
Francisco to Miami is through Phoenix, the forwarding table distills all the possible San Francisco-Miami
routes into the single route through Phoenix. All traffic with a destination address of Miami is sent
directly to the next hop, Phoenix.

After it receives a packet, the Phoenix router performs another route lookup, using the same destination
address. The Phoenix router then routes the packet appropriately. Although it considers the entire path,
the router at any individual hop along the way is responsible only for transmitting the packet to the next
hop in the path. If the Phoenix router is managing its traffic in a particular way, it might send the packet
through Houston on its route to Miami. This scenario is likely if specific customer traffic is treated as
priority traffic and routed through a faster or more direct route, while all other traffic is treated as
nonpriority traffic.

How the Routing and Forwarding Tables Are Synchronized

The Junos OS routing protocol process is responsible for synchronizing the routing information between
the routing and forwarding tables. To do this, the routing protocol process calculates the active routes
from all the routes in the routing table and installs them into the forwarding table. The routing protocol
process then copies the forwarding table to the router’s Packet Forwarding Engine, the part of the router
that forwards packets. Figure 2 on page 7 illustrates how the routing tables are synchronized.
 7

Figure 2: Synchronizing Routing Exchange Between the Routing and Forwarding Tables

NetFlow V9 Support

NetFlow Services Export Version 9 (NetFlow V9) provides an extensible and flexible method for using
templates to observe packets on a router. Each template indicates the format in which the router
exports data.

This feature supports Netflow V5 or V8 for flow-based devices.

For more information, see Monitoring, Sampling, and Collection Services Interfaces User Guide.

RELATED DOCUMENTATION

Understanding Junos OS Routing Tables

Routing Instances Overview

You can create multiple instances of BGP, IS-IS, LDP, Multicast Source Discovery Protocol (MSDP), OSPF
version 2 (usually referred to simply as OSPF), OSPF version 3 (OSPFv3), Protocol Independent
Multicast (PIM), RIP, RIP next generation (RIPng), and static routes by including statements at the
following hierarchy levels:

• [edit routing-instances routing-instance-name protocols]

• [edit logical-systems logical-system-name routing-instances routing-instance-name protocols]

 8

Only one instance of each protocol can be configured in a single routing instance.

NOTE: You can also create multiple routing instances for separating routing tables, routing
policies, and interfaces for individual DHCP wholesale subscribers (retailers) in a layer 3
wholesale network. For information about how to configure layer 3 wholesale network services,
see the Junos OS Broadband Subscriber Management and Services Library.

A routing instance is a collection of routing tables, interfaces, and routing protocol parameters. The set
of interfaces belongs to the routing tables, and the routing protocol parameters control the information
in the routing tables. There can be multiple routing tables for a single routing instance—for example,
unicast IPv4, unicast IPv6, and multicast IPv4 routing tables can exist in a single routing instance.
Routing protocol parameters and options control the information in the routing tables.

Each routing instance has a unique name and a corresponding IP unicast table. For example, if you
configure a routing instance with the name my-instance, the corresponding IP unicast table is my-
instance.inet.0. All routes for my-instance are installed into my-instance.inet.0.

NOTE: The default routing instance, master, refers to the main inet.0 routing table. The master
routing instance is reserved and cannot be specified as a routing instance.

Each routing instance consists of sets of the following:

• Routing tables

• Interfaces that belong to these routing tables (optional, depending upon the routing instance type)

NOTE: The commit operation fails, if the same logical interface is configured for both layer 2
circuit and ccc connection.

• Routing option configurations

You can configure 13 types of routing instances:

• Ethernet VPN (EVPN) (MX Series routers only)—Use this routing instance type to connect a group of
dispersed customer sites using a Layer 2 virtual bridge.

• Forwarding—Use this routing instance type for filter-based forwarding applications. For this instance
type, there is no one-to-one mapping between an interface and a routing instance. All interfaces
belong to the default instance inet.0.
 9

• Internet Multicast over MPLS—Use this routing instance type to provide support for ingress
replication provider tunnels to carry IP multicast data between routers through an MPLS cloud, using
MBGP or next-generation MVPN.

• Layer 2 Backhaul VPN—(MX Series routers only) Use this routing instance type to provide support
for Layer 2 wholesale VLAN packets with no existing corresponding logical interface. When using
this instance, the router learns both the outer tag and inner tag of the incoming packets, when the
instance-role statement is defined as access, or the outer VLAN tag only, when the instance-role
statement is defined as nni.

• Layer2-control—(MX Series routers only) Use this routing instance type for RSTP or MSTP in
customer edge interfaces of a VPLS routing instance. This instance type cannot be used if the
customer edge interface is multihomed to two provider edge interfaces. If the customer edge
interface is multihomed to two provider edge interfaces, use the default BPDU tunneling.

• Layer 2 VPN—Use this routing instance type for Layer 2 virtual private network (VPN)
implementations.

• MAC-VRF—(Various MX, QFX, ACX, PTX, and QFX platforms. For details on supported platforms and
Junos version support, see Feature Explorer. Use this routing instance type to configure multiple
customer-specific EVPN instances (EVIs) of type mac-vrf, each of which can support a different EVPN
service type. This configuration results in customer-specific virtual routing and forwarding (VRF)
tables with MAC addresses on each Juniper Networks device that serves as a virtual tunnel endpoint
(VTEP) in the EVPN-VXLAN network. This type of routing instance is for EVPN unicast routes only.

• MPLS forwarding—Use this routing instance type to provide support for protection against label
spoofing or errant label injection across autonomous system border routers (ASBRs).

• Nonforwarding—Use this routing instance type when a separation of routing table information is
required. There is no corresponding forwarding table. All routes are installed into the default
forwarding table. IS-IS instances are strictly nonforwarding instance types.

• Virtual router—Similar to a VPN routing and forwarding instance type, but used for non-VPN-related
applications. There are no virtual routing and forwarding (VRF) import, VRF export, VRF target, or
route distinguisher requirements for this instance type.

• Virtual switch—(MX Series routers only) Use the virtual switch instance type to isolate a LAN
segment with its Spanning Tree Protocol (STP) instance and separates its VLAN identifier space. For
more detail information about configuring a virtual switch, see the Junos OS Layer 2 Switching and
Bridging Library for Routing Devices.

• VPLS—Use the virtual private local-area network service (VPLS) routing instance type for point-to-
multipoint LAN implementations between a set of sites in a VPN.

• VRF—Use the VPN routing and forwarding routing (VRF) instance type for Layer 3 VPN
implementations. This routing instance type has a VPN routing table as well as a corresponding VPN
 10

forwarding table. For this instance type, there is a one-to-one mapping between an interface and a
routing instance. Each VRF instance corresponds with a forwarding table. Routes on an interface go
into the corresponding forwarding table.

Configure global routing options and protocols for the master instance by including statements at the
[edit protocols] and [edit routing-options] hierarchy levels. Routes are installed into the master routing
instance inet.0 by default, unless a routing instance is specified.

Multiple instances of BGP, OSPF, and RIP are used for Layer 3 VPN implementation. The multiple
instances of BGP, OSPF, and RIP keep routing information for different VPNs separate. The VRF
instance advertises routes from the customer edge (CE) router to the provider edge (PE) router and
advertises routes from the PE router to the CE router. Each VPN receives only routing information
belonging to that VPN.

Forwarding instances are used to implement filter-based forwarding for Common Access
Layer applications.

PIM instances are used to implement multicast over VPN applications.

Nonforwarding instances of IS-IS and OSPF can be used to separate a very large network into smaller
administrative entities. Instead of configuring a large number of filters, nonforwarding instances can be
used to filter routes, thereby instantiating policy. Nonforwarding instances can be used to reduce the
amount of routing information advertised throughout all components of a network. Routing information
associated with a particular instance can be announced where required, instead of being advertised to
the whole network.

Layer 2 VPN instances are used for Layer 2 VPN implementation.

Virtual router instances are similar to a VPN routing and forwarding instance type, but used for non-
VPN-related applications. There are no VRF import, VRF export, VRF target, or route distinguisher
requirements for this instance type.

Use the VPLS routing instance type for point-to-multipoint LAN implementations between a set of sites
in a VPN.

To configure a routing instance type, use the instance-type statement at the [edit routing-instances routing-
instance-name] hierarchy level.

To configure a routing instance, specify the following parameters:

• Name of the routing instance. Each routing instance has a unique name and a corresponding IP
unicast table. For example, if you configure a routing instance with the name my-instance, its
corresponding IP unicast table is my-instance.inet.0. All routes for my-instance are installed into my-
instance.inet.0.
 11

NOTE: You cannot specify a routing-instance name of default or include special characters
within the name of a routing instance.

• Type of routing instance.

• The interfaces that are bound to the routing instance. Interfaces not required for the forwarding
routing instance type.

To configure a routing instance, use the routing-instances statement at the [edit] hierarchy level.

You can create an instance of BGP, IS-IS, OSPF, OSPFv3, RIP, or RIPng by including configuration
statements at the [edit routing-instances routing-instance-name protocols] hierarchy level. You can also
configure static routes for the routing instance.

RELATED DOCUMENTATION

Junos OS VPNs Library for Routing Devices

Junos OS Layer 2 Switching and Bridging Library for Routing Devices
instance-type

Route Preferences Overview

IN THIS SECTION

Autonomous Systems | 12

Alternate and Tiebreaker Preferences | 12

Multiple Active Routes | 13

Dynamic and Static Routing | 13

Route Advertisements | 14

Route Aggregation | 15

For unicast routes, the Junos OS routing protocol process uses the information in its routing table, along
with the properties set in the configuration file, to choose an active route for each destination. While
the Junos OS might know of many routes to a destination, the active route is the preferred route to that
 12

destination and is the one that is installed in the forwarding table and used when actually routing
packets.

The routing protocol process generally determines the active route by selecting the route with the
lowest preference value. The preference value is an arbitrary value in the range from 0
through 4,294,967,295 (232 – 1) that the software uses to rank routes received from different protocols,
interfaces, or remote systems.

The preference value is used to select routes to destinations in external autonomous systems (ASs) or
routing domains; it has no effect on the selection of routes within an AS (that is, within an interior
gateway protocol [IGP]). Routes within an AS are selected by the IGP and are based on that protocol’s
metric or cost value.

This section includes the following topics:

Autonomous Systems

A large network or collection of routers under a single administrative authority is termed an

autonomous system (AS). Autonomous systems are identified by a unique numeric identifier that is
assigned by the Internet Assigned Numbers Authority (IANA). Typically, the hosts within an AS are
treated as internal peers, and hosts in a peer AS are treated as external peers. The status of the
relationship between hosts—internal or external—governs the protocol used to exchange routing
information.

Alternate and Tiebreaker Preferences

The Junos OS provides support for alternate and tiebreaker preferences, and some of the routing
protocols, including BGP and label switching, use these additional preferences. With these protocols,
you can specify a primary route preference (by including the preference statement in the configuration),
and a secondary preference that is used as a tiebreaker (by including the preference2 statement).

In order to use common comparison routines, Junos OS stores the 1's complement of the LocalPref value
in the Preference2 field. For example, if the LocalPref value for Route 1 is 100, the Preference2 value is -101.
If the LocalPref value for Route 2 is 155, the Preference2 value is -156. Route 2 is preferred because it has
a higher LocalPref value and a lower Preference2 value.

You can also mark route preferences with additional route tiebreaker information by specifying a color
and a tiebreaker color (by including the color and the tiebreaker color2 statements in the configuration).
color and color2 statements are even finer-grained preference values that Junos OS uses when preference
and preference2 statements fail to break the tie during route selection.

The software uses a 4-byte value to represent the route preference value. When using the preference
value to select an active route, the software first compares the primary route preference values,
choosing the route with the lowest value. If there is a tie and a secondary preference has been
 13

configured, the software compares the secondary preference values, choosing the route with the lowest
value. The secondary preference values must be included in a set for the preference values to be
considered.

Multiple Active Routes

The IGPs compute equal-cost multipath next hops, and IBGP picks up these next hops. When there are
multiple, equal-cost next hops associated with a route, the routing protocol process installs only one of
the next hops in the forwarding path with each route, randomly selecting which next hop to install. For
example, if there are 3 equal-cost paths to an exit routing device and 900 routes leaving through that
routing device, each path ends up with about 300 routes pointing at it. This mechanism provides load
distribution among the paths while maintaining packet ordering per destination.

BGP multipath does not apply to paths that share the same MED-plus-IGP cost yet differ in IGP cost.
Multipath path selection is based on the IGP cost metric, even if two paths have the same MED-plus-
IGP cost.

Random selection of equal-cost multipath occurs independently for inet.0 and inet.3 tables. This can lead
to a single prefix showing different bestpaths for inet.0 vs inet.3.

Dynamic and Static Routing

Entries are imported into a router's routing table from dynamic routing protocols or by manual inclusion
as static routes. Dynamic routing protocols allow routers to learn the network topology from the
network. The routers within the network send out routing information in the form of route
advertisements. These advertisements establish and communicate active destinations, which are then
shared with other routers in the network.

Although dynamic routing protocols are extremely useful, they have associated costs. Because they use
the network to advertise routes, dynamic routing protocols consume bandwidth. Additionally, because
they rely on the transmission and receipt of route advertisements to build a routing table, dynamic
routing protocols create a delay (latency) between the time a router is powered on and the time during
which routes are imported into the routing table. Some routes are therefore effectively unavailable until
the routing table is completely updated, when the router first comes online or when routes change
within the network (due to a host going offline, for example).

Static routing avoids the bandwidth cost and route import latency of dynamic routing. Static routes are
manually included in the routing table, and never change unless you explicitly update them. Static routes
are automatically imported into the routing table when a router first comes online. Additionally, all traffic
destined for a static address is routed through the same router. This feature is particularly useful for
networks with customers whose traffic must always flow through the same routers. Figure 3 on page
14 shows a network that uses static routes.
 14

Figure 3: Static Routing Example

In Figure 3 on page 14, the customer routes in the 192.176.14/24 subnetwork are static routes. These are
hard links to specific customer hosts that never change. Because all traffic destined for any of these
routes is forwarded through Router A, these routes are included as static routes in Router A's routing
table. Router A then advertises these routes to other hosts so that traffic can be routed to and from
them.

Route Advertisements

The routing table and forwarding table contain the routes for the routers within a network. These routes
are learned through the exchange of route advertisements. Route advertisements are exchanged
according to the particular protocol being employed within the network.

Generally, a router transmits hello packets out each of its interfaces. Neighboring routers detect these
packets and establish adjacencies with the router. The adjacencies are then shared with other
neighboring routers, which allows the routers to build up the entire network topology in a topology
database, as shown in Figure 4 on page 14.

Figure 4: Route Advertisement

In Figure 4 on page 14, Router A sends out hello packets to each of its neighbors. Routers B and C
detect these packets and establish an adjacent relationship with Router A. Router B and C then share
this information with their neighbors, Routers D and E, respectively. By sharing information throughout
the network, the routers create a network topology, which they use to determine the paths to all
 15

possible destinations within the network. The routes are then distilled into the forwarding table of best
routes according to the route selection criteria of the protocol in use.

Route Aggregation

As the number of hosts in a network increases, the routing and forwarding tables must establish and
maintain more routes. As these tables become larger, the time routers require to look up particular
routes so that packets can be forwarded becomes prohibitive. The solution to the problem of growing
routing tables is to group (aggregate) the routers by subnetwork, as shown in Figure 5 on page 15.

Figure 5: Route Aggregation

Figure 5 on page 15 shows three different ASs. Each AS contains multiple subnetworks with thousands
of host addresses. To allow traffic to be sent from any host to any host, the routing tables for each host
must include a route for each destination. For the routing tables to include every combination of hosts,
the flooding of route advertisements for each possible route becomes prohibitive. In a network of hosts
numbering in the thousands or even millions, simple route advertisement is not only impractical but
impossible.

By employing route aggregation, instead of advertising a route for each host in AS 3, the gateway router
advertises only a single route that includes all the routes to all the hosts within the AS. For example,
instead of advertising the particular route 170.16.124.17, the AS 3 gateway router advertises only
170.16/16. This single route advertisement encompasses all the hosts within the 170.16/16
 16

subnetwork, which reduces the number of routes in the routing table from 216 (one for every possible IP
address within the subnetwork) to 1. Any traffic destined for a host within the AS is forwarded to the
gateway router, which is then responsible for forwarding the packet to the appropriate host.

Similarly, in this example, the gateway router is responsible for maintaining 216 routes within the AS (in
addition to any external routes). The division of this AS into subnetworks allows for further route
aggregation to reduce this number. In the subnetwork in the example, the subnetwork gateway router
advertises only a single route (170.16.124/24), which reduces the number of routes from 28 to 1.

Understanding Route Preference Values (Administrative Distance)

The Junos OS routing protocol process assigns a default preference value (also known as an
administrative distance) to each route that the routing table receives. The default value depends on the
source of the route. The preference value is a value from 0 through 4,294,967,295 (232 – 1), with a
lower value indicating a more preferred route. Table 1 on page 16 lists the default preference values.

Table 1: Default Route Preference Values

How Route Is Learned Default Statement to Modify Default Preference

Preference

Directly connected network 0 –

System routes 4 –

Static and Static LSPs 5 static

ARI-TS 5 ARI-TS preference.

Starting in Junos OS Release 22.2R1, ARI routes are installed

as ARI-TS protocol routes instead of static routes as installed
in the earlier Junos OS releases.
 17

Table 1: Default Route Preference Values (Continued)

How Route Is Learned Default Statement to Modify Default Preference

Preference

Static LSPs 6 MPLS preference

NOTE: In Junos OS Releases prior to 10.4, if you configure a

static MPLS LSP using the static-path statement, the default
preference value is 5. Starting in Junos OS Release 10.4, if
you configure a static-label-switched-path the default
preference value is 6. The previous configuration statement
static-path is hidden in Junos OS Release 10.4 and later
releases.

RSVP-signaled LSPs 7 RSVP preference as described in the MPLS Applications User

Guide

SR-TE 8 SR-TE preference

LDP-signaled LSPs 9 LDP preference, as described in the MPLS Applications User

Guide

OSPF internal route 10 OSPF preference

OSPF SR route 10 Labelled OSPF preference

access-internal route 12 –

access route 13 –

IS-IS SR route 14 Labelled IS-IS preference

IS-IS Level 1 internal route 15 IS-IS preference

IS-IS Level 2 internal route 18 IS-IS preference

 18

Table 1: Default Route Preference Values (Continued)

How Route Is Learned Default Statement to Modify Default Preference

Preference

Redirects 30 –

Kernel 40 –

SNMP 50 –

Router discovery 55 –

RIP 100 RIP preference

RIPng 100 RIPng preference

PIM 105 Junos OS Multicast Protocols User Guide

DVMRP 110 Junos OS Multicast Protocols User Guide

Aggregate 130 aggregate

OSPF AS external routes 150 OSPF external-preference

IS-IS Level 1 external route 160 IS-IS external-preference

IS-IS Level 2 external route 165 IS-IS external-preference

BGP 170 BGP preference, export, import

MSDP 175 Junos OS Multicast Protocols User Guide

In general, the narrower the scope of the statement, the higher precedence its preference value is given,
but the smaller the set of routes it affects. To modify the default preference value for routes learned by
routing protocols, you generally apply routing policy when configuring the individual routing protocols.
 19

You also can modify some preferences with other configuration statements, which are indicated in the
table.

Release History Table

Release Description

10.4 Starting in Junos OS Release 10.4, if you configure a static-label-switched-path the default preference
value is 6.

RELATED DOCUMENTATION

Routing Policies, Firewall Filters, and Traffic Policers User Guide

Equal-Cost Paths and Load Sharing Overview

For equal-cost paths, load sharing is based on the BGP next hop. For example, if four prefixes all point to
a next hop and there is more than one equal-cost path to that next hop, the routing protocol process
uses a hash algorithm to choose the path among the four prefixes. Also, for each prefix, the routing
protocol process installs a single forwarding entry pointing along one of the paths. The routing software
does not rehash the path taken as prefixes pointing to the next hop come and go, but it does rehash if
the number of paths to the next hop changes. Because a prefix is tied to a particular path, packet
reordering should not happen. The degree of load sharing improves as the number of prefixes increases.

RELATED DOCUMENTATION

Load Balancing for a BGP Session

Routing Protocol Process Overview

Junos OS is based on the FreeBSD Unix operating system. The open source software is modified and
hardened to operate in the device’s specialized environment. For example, some executables have been
deleted, while other utilities were de-emphasized. Additionally, certain software processes were added
to enhance the routing functionality. The result of this transformation is the kernel, the heart of the
Junos OS software.
 20

The kernel is responsible for operating multiple processes that perform the actual functions of the
device. Each process operates in its own protected memory space, while the communication among all
the processes is still controlled by the kernel. This separation provides isolation between the processes,
and resiliency in the event of a process failure. This is important in a core routing platform because a
single process failure does not cause the entire device to cease functioning.

Some of the common software processes include the routing protocol process (rpd) that controls the
device’s protocols, the device control process (dcd) that controls the device’s interfaces, the
management process (mgd) that controls user access to the device, the chassis process (chassisd) that
controls the device’s properties itself, and the Packet Forwarding Engine process (pfed) that controls the
communication between the device’s Packet Forwarding Engine and the Routing Engine. The kernel also
generates specialized processes as needed for additional functionality, such as SNMP, the Virtual Router
Redundancy Protocol (VRRP), and Class of Service (CoS).

The routing protocol process is a software process within the Routing Engine software, which controls
the routing protocols that run on the device. Its functionality includes all protocol messages, routing
table updates, and implementation of routing policies.

The routing protocol process starts all configured routing protocols and handles all routing messages. It
maintains one or more routing tables, which consolidate the routing information learned from all routing
protocols. From this routing information, the routing protocol process determines the active routes to
network destinations and installs these routes into the Routing Engine’s forwarding table. Finally, it
implements routing policy, which allows you to control the routing information that is transferred
between the routing protocols and the routing table. Using routing policy, you can filter and limit the
transfer of information as well as set properties associated with specific routes.

RELATED DOCUMENTATION

show system processes

show task
show task memory
 21

CHAPTER 2

Overview of IPv6 Routing

IN THIS CHAPTER

IPv6 Overview | 21

Understanding IPv6 | 25

Supported IPv6 Standards | 31

IPv6 Support on Devices Running Junos OS | 35

IPv6 Overview

IN THIS SECTION

IPv6 Packet Headers | 22

IPv6 Addressing | 23

IP version 6 (IPv6) is the latest version of IP. IP enables numerous nodes on different networks to
interoperate seamlessly. IP version 4 (IPv4) is currently used in intranets and private networks, as well as
the Internet. IPv6 is the successor to IPv4, and is based for the most part on IPv4.

IPv4 has been widely deployed and used to network the Internet today. With the rapid growth of the
Internet, enhancements to IPv4 are needed to support the influx of new subscribers, Internet-enabled
devices, and applications. IPv6 is designed to enable the global expansion of the Internet.

IPv6 builds upon the functionality of IPv4, providing improvements to addressing, configuration and
maintenance, and security.

IPv6 offers the following benefits:

• Expanded addressing capabilities—IPv6 provides a larger address space. IPv6 addresses consist of
128 bits, while IPv4 addresses consist of 32 bits. 128-bit addressing increases the address space by
approximately 10^29 unique addresses, enough to last for the forseeable future.
 22

• Header format simplification—IPv6 packet header format is designed to be efficient. IPv6

standardizes the size of the packet header to 40 bytes, divided into 8 fields.

• Improved support for extensions and options—Extension headers carry Internet-layer information
and have a standard size and structure.

• Flow labeling capability—Flow labels provide consistent handling of packets belonging to the same
flow.

• Improved privacy and security—IPv6 supports extensions for authentication and data integrity, which
enhance privacy and security.

This section discusses the following topics:

IPv6 Packet Headers

IPv6 headers are different from IPv4 headers. Learn about IPv6 header and IPv6 extension headers.

IPv6 Header Structure

Figure 6: IPv6 Header Structure

IPv6 packet headers contain many of the fields found in IPv4 packet headers; some of these fields have
been modified from IPv4. Figure 6 on page 22 shows the following 8 fields that are available in the 40-
byte IPv6 header.

IPv6 packet headers contain many of the fields found in IPv4 packet headers; some of these fields have
been modified from IPv4. The 40-byte IPv6 header consists of the following 8 fields:

• Version—Version of IP.

• Traffic class—Class-of-service (CoS) priority of the packet. Previously the type-of-service (ToS) field in
IPv4. However, the semantics of this field (for example, DiffServ code points) are identical to IPv4.
 23

• Flow label—Packet flows requiring a specific class of service. The flow label identifies all packets
belonging to a specific flow, and routers can identify these packets and handle them in a similar
fashion.

• Payload length—Length of the IPv6 payload. Previously the total length field in IPv4.

• Next header—Next extension header to examine. Previously the protocol field in IPv4.

• Hop limit—Maximum number of hops allowed. Previously the time-to-live (TTL) field in IPv4.

• Source address—Address of the source node sending the packet.

• Destination address—Final destination node address for the packet.

IPv6 Extension Headers

In IPv6, extension headers are used to encode optional Internet-layer information. Extension headers
are placed between the IPv6 header and the upper layer header in a packet.

Extension headers are chained together using the next header field in the IPv6 header. The next header
field indicates to the router which extension header to expect next. If there are no more extension
headers, the next header field indicates the upper layer header (TCP header, User Datagram Protocol
[UDP] header, ICMPv6 header, an encapsulated IP packet, or other items).

For information on IPv6, refer to RFC 2460.

IPv6 Addressing

IPv6 uses a 128-bit addressing model. This creates a much larger address space than IPv4 addresses,
which are made up of 32 bits. IPv6 addresses also contain a scope field that categorizes what types of
applications are suitable for the address. IPv6 does not support broadcast addresses, but instead uses
multicast addresses to serve this role. In addition, IPv6 also defines a new type of address called anycast.

You cannot configure a subnet zero IPv6 address because RFC 2461 reserves the subnet-zero address
for anycast addresses, and Junos OS complies with the RFC.

This section discusses the following topics that provide background information about IPv6 addressing:

Address Representation

IPv6 addresses consist of 8 groups of 16-bit hexadecimal values separated by colons (:). The IPv6
address format is as follows:

aaaa:aaaa:aaaa:aaaa:aaaa:aaaa:aaaa:aaaa
 24

aaaa is a 16-bit hexadecimal value, and a is a 4-bit hexadecimal value. Following is an example of an
actual IPv6 address:

3FFE:0000:0000:0001:0200:F8FF:FE75:50DF

You can omit the leading zeros, as shown:

3FFE:0:0:1:200:F8FF:FE75:50DF

You can compress 16-bit groups of zeros to the notation :: (two colons), as shown here, but only once
per address:

3FFE::1:200:F8FF:FE75:50DF

Address Types

There are three types of IPv6 addresses:

• Unicast—For a single interface.

• Multicast—For a set of interfaces on the same physical medium. A packet is sent to all of the
interfaces associated with the address.

• Anycast—For a set of interfaces on different physical mediums. A packet is sent to only one of the
interfaces associated with this address, not to all the interfaces.

Address Scope

IPv6 addresses have scope, which identifies the application suitable for the address. Unicast and
multicast addresses support scoping.

Unicast addresses support two types of scope: global scope and local scope. There are two types of local
scope: link-local addresses and site-local addresses. Link-local unicast addresses are used within a single
network link. The first ten bits of the prefix identify the address as a link-local address. Link-local
addresses cannot be used outside a network link. Site-local unicast addresses are used within a site or
intranet. A site consists of multiple network links, and site-local addresses identify nodes inside the
intranet. Site-local addresses cannot be used outside the site.

Multicast addresses support 16 different types of scope, including node, link, site, organization, and
global scope. A 4-bit field in the prefix identifies the scope.
 25

Address Structure

Unicast addresses identify a single interface. The address consists of n bits for the prefix, and 128 –
n bits for the interface ID.

Multicast addresses identify a set of interfaces. The address is made up of the first 8 bits of all ones, a 4-
bit flags field, a 4-bit scope field, and a 112-bit group ID:

11111111 | flags | scope | group ID

The first octet of ones identifies the address as a multicast address. The flags field identifies whether the
multicast address is a well-known address or a transient multicast address. The scope field identifies the
scope of the multicast address. The 112-bit group ID identifies the multicast group.

Similar to multicast addresses, anycast addresses identify a set of interfaces. However, packets are sent
to only one of the interfaces, not to all interfaces. Anycast addresses are allocated from the normal
unicast address space and cannot be distinguished from a unicast address in format.

RELATED DOCUMENTATION

IPv6 Flow-Based Processing Overview

Understanding IPv6

IN THIS SECTION

What is IPv6? | 26

IPv6 Address Format | 27

Implementations at Juniper Networks | 28

IPv4 and IPv6 Collaboration | 29

Service providers and some enterprises are faced with growing their networks using IPv6, while
continuing to serve IPv4 customers.
 26

Juniper Networks has made significant investments in technologies and solutions that enable
enterprises and service providers to meet mixed IP addressing needs even as they build out IPv6
networks as rapidly as markets and services require.

Increasingly, the public side of network address translation (NAT) devices is IPv6 rather than IPv4.
Service providers cannot continue giving customers globally routable IPv4 addresses, they cannot get
new globally routable IPv4 addresses for expanding their own networks, and yet they must continue to
serve both IPv4 customers and new customers, all of whom are primarily trying to reach IPv4
destinations.

IPv4 and IPv6 must coexist for some number of years, and their coexistence must be transparent to end
users. If an IPv4-to-IPv6 transition is successful, the end users should not even notice it.

What is IPv6?

IP version 6 (IPv6) is the latest version of IP. IPv6 builds upon the functionality of IPv4, providing
improvements to addressing, configuration and maintenance, and security. Juniper Networks is focused
on helping service provider and enterprise customers deploy IPv6 in ways that improve current
networks.

IPv6 offers the following benefits:

• Expanded addressing capabilities—IPv4 uses 32-bit addresses and can support 4.3 billion devices
connected directly to the Internet. IPv6, on the other hand, uses 128-bit addresses and supports a
virtually unlimited number of devices—2 to the 128th power.

• Header format simplification—IPv6 packet header format is designed to be efficient. IPv6

standardizes the size of the packet header to 40 bytes, divided into 8 fields. Figure 7 on page 27
provides a comparison between the packet headers of the two protocol versions.
 27

Figure 7: IPv4 and IPv6 Header Comparison

• Improved support for extensions and options—Extension headers carry Internet-layer information
and have a standard size and structure.

• Flow labeling capability—Flow labels provide consistent handling of packets belonging to the same
flow.

• Improved privacy and security—IPv6 supports extensions for authentication and data integrity, which
enhance privacy and security.

IPv6 Address Format

IPv6 addresses consist of eight hexadecimal groups. Each hexadecimal group, separated by a colon (:),
consists of a 16-bit hexadecimal value. The following is an example of the IPv6 format:

xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx

A group of xxxx represents the 16-bit hexadecimal value. Each individual x represents a 4-bit
hexadecimal value. The following is an example of a possible IPv6 address:

4FDE:0000:0000:0002:0022:F376:FF3B:AB3F

The first sixty four bits (4FDE:0000:0000:0002) are network bits, the remaining ones are the host's
interface identifier (host bits). The network portion is provided by an ISP or by the registry (ARIN or
RIPE).

The length of the prefix depends on the size of your organiztion:

 28

• Registries are assigned /23.

• ISPs are assigned /32.

• Sites are assigned /48.

Say, you are the organization that receives a /48 prefix like this:
4FDE:0000:0000:0000:0000:0000:0000:0000/48. This gives you two bytes (shown in itallics) in the
network portion to create different networks (itallic portion: 2^16=65536 different numbers). As a
shortcut, this network address space can be represented as 4FDE::/48.

To create the host portion of IPv6 address, if DHCP is not used, you have several options.

Table 2 on page 28 lists the host addressing strategies.

Table 2: IPv6 Host Portion Techniques

Ways to Create the Host Example

Portion of an IPv6
Address

Embed an IPv4 address in 4FDE::101.45.75.219

an IPv6 address

Manually 4FDE::1

EUI-64 Automatically create the host portion of IPv6 address based on the MAC address of
the first Ethernet interface

For an example of manually assigned host addresses, see Example: Configure IPv6 Static Routing for a
Stub Network. For an example of EUI-64 assigned host addresses, see Example: Configuring a Basic
RIPng Network.

Implementations at Juniper Networks

When deploying IPv6, you can gain a great advantage by using Juniper Networks high-end routers
because IPv6 has been implemented directly in the ASICs (Application-Specific Integrated Circuit).
Having IPv6 compatibility in the hardware means that IPv6 packets can be forwarded at line rate –
unlike many competing routers.

After over a decade of development, the IPv6 functionality in Juniper Networks products is extensive.
Junos OS, for over ten years has had IPv6 support. Juniper has a tremendous presence on various
technical bodies that have specified IPv6. Juniper had already enabled IPv6 across all of its platforms
and interfaces back in 2002. Juniper was at the forefront of shipping IPv6-ready firewall and VPN gear
 29

in 2004. And Juniper was the first to have its routers certified as IPv6 capable by the U.S. Defense
Department in 2007.

Just to highlight a few, Junos OS fully supports the following IPv6 RFCs:

• RFC 2460, Internet Protocol, Version 6 (IPv6) Specification

• RFC 3513, Internet Protocol Version 6 (IPv6) Addressing Architecture

• RFC 2893, Transition Mechanisms for IPv6 Hosts and Routers

For a complete list of supported IPv6 RFCs, see "Supported IPv6 Standards" on page 31.

IPv4 and IPv6 Collaboration

IPv6 is the biggest upgrade in the 40-year history of the Internet. Forward-looking carriers and
enterprises are deploying IPv6 because the Internet has run out of allocatable IP addresses using the
current IPv4 standard. Juniper is putting its energy into supporting native IPv6 as well as dual-stack
configurations where IPv6 runs alongside IPv4 in all of its products. Juniper fully supports an IPv4-to-
IPv6 transition mechanism known as Dual-Stack Lite, and it has been a leader in another approach called
6PE for use with multiprotocol label switching (MPLS) networks.

Keep in mind that if you are going to dual stack all of your network devices, the interfaces need both an
IPv6 and an IPv4 address. This raises the issue that the Internet has run out of IPv4 addresses, which is
the main reason we need IPv6 in the first place. If you do not have an abundant supply of IPv4
addresses to apply to your devices, you can still use dual stacking, but you will need to conserve your
supply of IPv4 addresses by using network address translation (NAT).

Building dual stacked networks with a mix of global IPv6 addresses and NAT-ed IPv4 addresses is quite
feasible. Some specific solutions include carrier-grade NAT (CGN), NAT444, NAT464, and dual-stack
lite.

Table 3 on page 30 lists the types of IP transition strategies supported by Juniper Networks.
 30

Table 3: IPv4 and IPv6 Collaboration Strategies

IPv4 and IPv6 Purpose

Collaboration Strategy

Carrier-grade NAT— To maintain IPv4 subscriber growth after IPv4 exhaustion, the remaining IPv4
Sharing IPv4 addresses addresses will have to be shared among end users. This is done with carrier-grade
NAT (CGN). Rather than assigning public addresses directly to individual users, CGN
“pulls back” these addresses to a more centralized Network Address Translation
(NAT) point, allowing the sharing of a single public address among a much larger
number of end devices. There are several variations in the deployment architecture
of CGN. Dual Stack Lite (DS-Lite) and NAT44(4) are the most important ones for
coexistence strategies. They are similar in the way that they enable providers to
share a small set of IPv4 addresses among a large number of users. They differ in the
way that packets are carried to the CGN. With DS-Lite, they are carried as IPv4
through an IPv6 tunnel; with NAT44(4) they are carried over IPv4.

NAT44(4) NAT44(4) is an architecture that uses the NAT44 protocol to extend the life of a
customer’s IPv4 address pool by allowing multiple subscribers or end users to share
a single public IPv4 address. NAT44(4) requires no change to the service provider’s
existing network infrastructure, and can be used in conjunction with 6rd for further
benefits. In NAT44(4), the subscribers have their own private IPv4 (RFC1918)
address space behind their customer premises equipment (CPE). The service
provider translates the subscriber’s address to another IPv4 address in the access
network to allow better utilization of the existing public IPv4 address space by
aggregating subscribers in a public IPv4 pool on the carrier-grade NAT (CGN) router.

Dual Stack Lite (DS-Lite) DS-Lite uses tunneling and NAT44 to mitigate IPv4 address depletion while
incrementally adopting IPv6. When a device in the customer network sends an IPv4
packet to any destination, the IPv4 packet is encapsulated in an IPv6 packet for
transport into the provider network. The address family transition router (AFTR)
decapsulates the packet back to IPv4, and uses NAT44 to translates the private IPv4
address to a public IPv4 address and delivers the packet to the Internet.
 31

Table 3: IPv4 and IPv6 Collaboration Strategies (Continued)

IPv4 and IPv6 Purpose

Collaboration Strategy

Additional Juniper • NAT64—provides IPv6 to IPv4 translation allowing IPv6-only hosts to access
Networks supported IPv4-only hosts.
IPv4/IPv6 technologies
• 6to4—connects IPv6 hosts or networks across an IPv4 infrastructure or Internet.

• 6rd—provides rapid deployment of IPv6 service to end users over an existing

IPv4 infrastructure.

• IPv4/IPv6 dual stack—Junos OS supports IPv4/IPv6 dual stack, allowing

concurrent independent operation of both protocols on a single router.

RELATED DOCUMENTATION

Ethernet Interfaces User Guide for Routing Devices

IPv6 Neighbor Discovery User Guide
Class of Service User Guide (Routers and EX9200 Switches)
RIP User Guide
Configuring MLD
Day One: Exploring IPv6
Day One: Advanced IPv6 Configuration
https://www.juniper.net/ipv6

Supported IPv6 Standards

Junos OS substantially supports the following RFCs and Internet drafts, which define standards for IP
version 6 (IPv6):

• RFC 2373, IP Version 6 Addressing Architecture

• RFC 2375, Multicast Address Assignments

• RFC 2461, Neighbor Discovery for IP Version 6 (IPv6)

• RFC 2462, IPv6 Stateless Address Autoconfiguration

 32

• RFC 2463, Internet Control Message Protocol (ICMPv6) for the Internet Protocol Version 6 (IPv6)
Specification

• RFC 2464, Transmission of IPv6 Packets over Ethernet Networks

• RFC 2465, Management Information Base for IP Version 6: Textual Conventions and General Group

IP version 6 (IPv6) and Internet Control Message Protocol version 6 (ICMPv6) statistics are not
supported.

• RFC 2472, IP Version 6 over PPP

• RFC 2474, Definition of the Differentiated Services Field (DS Field) in the IPv4 and IPv6 Headers

• RFC 2491, IPv6 Over Non-Broadcast Multiple Access (NBMA) networks

• RFC 2492, IPv6 over ATM Networks

• RFC 2526, Reserved IPv6 Subnet Anycast Addresses

• RFC 2545, Use of BGP-4 Multiprotocol Extensions for IPv6 Inter-Domain Routing

• RFC 2578, Structure of Management Information Version 2 (SMIv2)

• RFC 2675, IPv6 Jumbograms

• RFC 2711, IPv6 Router Alert Option

• RFC 2767, Dual Stack Hosts using the "Bump-In-the-Stack" Technique (BIS)

• RFC 2784, Generic Routing Encapsulation

• RFC 2878, PPP Bridging Control Protocol (BCP)

• RFC 3306, Unicast-Prefix-based IPv6 Multicast Addresses

• RFC 3307, Allocation Guidelines for IPv6 Multicast Addresses

• RFC 3315, Dynamic Host Configuration Protocol for IPv6 (DHCPv6)

Address assignment is supported with IP version 4 (IPv4) but not IP version 6 (IPv6).

• RFC 3513, Internet Protocol Version 6 (IPv6) Addressing Architecture

• RFC 3515, The Session Initiation Protocol (SIP) Refer Method

• RFC 3590, Source Address Selection for the Multicast Listener D (Supported for SSM include mode
only)

• RFC 3768, Virtual Router Redundancy Protocol (VRRP)

 33

• RFC 3810, Multicast Listener Discovery Version 2 (MLDv2) for IPv6

• RFC 3879, Deprecating Site Local Addresses

• RFC 3971, Secure Neighbor Discovery for IPv6 (No support for certification paths, anchored on
trusted parties)

• RFC 3972, Cryptographically Generated Addresses

• RFC 4007, IPv6 Scoped Address Architecture

• RFC 4087, IP Tunnel MIB

• RFC 4193, Unique Local IPv6 Unicast Addresses

• RFC 4213, Basic Transition Mechanisms for IPv6 Hosts and Routers

RFC 4213 supersedes RFC 2893, Transition Mechanisms for IPv6 Hosts and Routers.

NOTE: On EX Series switches, except for the EX9200 Series, only dual IP layer is supported.
On EX9200 Series switches, both dual IP layer and configured tunneling of IPv6 over IPv4 are
supported.

• RFC 4291, IP Version 6 Addressing Architecture

• RFC 4292, IP Forwarding Table MIB

• RFC 4293, Management Information Base for the Internet Protocol (IP)

• RFC 4294, IPv6 Node Requirements (Partial support)

• RFC 4443, Internet Control Message Protocol (ICMPv6) for the Internet Protocol Version 6 (IPv6)
Specification

• RFC 4552, Authentication/Confidentiality for OSPFv3

• RFC 4604, Using Internet Group Management Protocol Version 3 (IGMPv3)

• RFC 4659, BGP-MPLS IP Virtual Private Network (VPN) Extension for IPv6 VPN

• RFC 4798, Connecting IPv6 Islands over IPv4 MPLS Using IPv6 Provider Edge Routers (6PE)

Option 4b (eBGP redistribution of labeled IPv6 routes from AS to neighboring AS) is not supported.

• RFC 4861 Neighbor Discovery for IP Version 6 (IPv6)

• RFC 4862, IPv6 Stateless Address Autoconfiguration

 34

• RFC 4884, Extended ICMP to Support Multi-Part Messages

• RFC 4890, Recommendations for Filtering ICMPv6 Messages in Firewalls

• RFC 4942, IPv6 Transition/Coexistence Security Considerations

• RFC 5072, IP Version 6 over PPP

• RFC 5095, Deprecation of Type 0 Routing Headers in IPv6

• RFC 5308, Routing IPv6 with IS-IS

• RFC 5340, OSPF for IPv6 (RFC 2740 is obsoleted by RFC 5340)

• RFC 5575, Dissemination of Flow Specification Rules

• RFC 5798, Virtual Router Redundancy Protocol (VRRP) Version 3 for IPv4 and IPv6

• RFC 5905, Network Time Protocol Version 4 (for IPv6)

• RFC 5952, A Recommendation for IPv6 Address Text Representation

• RFC 6164, Using 127-Bit IPv6 Prefixes on Inter-Router Links

• RFC 6527, Definitions of Managed Objects for the Virtual Router Redundancy Protocol Version 3
(VRRPv3)

The following features are not supported:

• Row creation

• Set operation

• vrrpv3StatisticsPacketLengthErrors MIB object

• vrrpv3StatisticsRowDiscontinuityTime MIB object

• RFC 6583, Operational Neighbor Discovery Problems

Only Prioritize NDP Activities, Tuning of the NDP Queue Rate Limit, and Queue Tuning are
supported.

• RFC 6724, Default Address Selection for Internet Protocol version 6 (IPv6)

• RFC 8200, Internet Protocol, Version 6 (IPv6) Specification

• RFC 8201, Path MTU Discovery for IP version 6

• RFC 8335, PROBE: A Utility for Probing Interfaces

• Internet draft draft-ietf-l3vpn-bgp-ipv6-07.txt, BGP-MPLS IP VPN extension for IPv6 VPN

 35

• Internet draft draft-ietf-lsr-flex-algo-20.txt, IGP Flexible Algorithm to allow IGPs to compute

constraint-based paths over the network.

• Internet draft draft-ietf-idr-flow-spec-00.txt, Dissemination of flow specification rules

• Internet draft draft-ietf-softwire-dual-stack-lite-04.txt, Dual-Stack Lite Broadband Deployments

Following IPv4 Exhaustion

• Internet draft draft-kato-bgp-ipv6-link-local-00.txt, BGP4+ Peering Using IPv6 Link-local Address

The following RFCs and Internet draft do not define standards, but provide information about IPv6 and
related technologies. The IETF classifies them variously as “Experimental” or “Informational.”

• RFC 1901, Introduction to Community-based SNMPv2

• RFC 2767, Dual Stack Hosts using the "Bump-In-the-Stack" Technique (BIS)

• RFC 3587, IPv6 Global Unicast Address Format

• Internet draft draft-ietf-ngtrans-bgp-tunnel-04.txt, Connecting IPv6 Islands across IPv4 Clouds with
BGP

Only MP-BGP over IP version 4 (IPv4) approach is supported.

RELATED DOCUMENTATION

Supported IPv4, TCP, and UDP Standards

Accessing Standards Documents on the Internet

IPv6 Support on Devices Running Junos OS

IPv6 builds upon the functionality of IPv4, providing improvements to addressing, configuration and
maintenance, and security. The following IPv6 features are supported:

• IPv6 path maximum transmission unit (MTU) discovery

Path MTU Discovery is used by single-source devices to determine the correct size of fragments.
Path MTU Discovery is enabled for IPv6 packets by default.

• Dynamic routes distribution through IS-IS and OSPF for IPv6

Routers learn routes through different routing protocols such as OSPF, BGP, or IS-IS. Learned routes
are put in the routing table to enable IPv6 traffic forwarding.
 36

• Dual stacking (IPv4 and IPv6)

Dual stacking allows a device to run both IPv4 and IPv6 at the same time. End nodes, routers, and
switches run both protocols and use IPv6 as the preferred protocol.

• IPv6 forwarding

The port forwarding engine software supports unicast IPv6 routes and next hops. This includes basic
route infrastructure, next-hop support, network infrastructure, and exception packet processing.

• IPv6 over MPLS (6PE)

Devices can interconnect IPv6 islands over an MPLS-enabled IPv4 network. IPv6 information is sent
over the MPLS core using MG-BGP with IPv4. The BGP Next Hop field conveys the IPv4 address of
the router so that MPLS LSPs can be used without explicit tunnel configuration.

• Neighbor Discovery

The Neighbor Discovery protocol facilitates a substantial number of functions related to local
network connectivity, datagram routing, and configuration. Both regular hosts and routers in an IPv6
environment count on the Neighbor Discovery protocol to facilitate the important exchanges of
information that are necessary for proper internetwork operations. Neighbor Discovery is a
messaging protocol similar to ICMP. The following functions are performed by the protocol:

• Router discovery—How a host locates routers residing on an attached link.

• Prefix discovery—How a host discovers address prefixes for destinations residing on an attached
link. Nodes use prefixes to distinguish between destinations that reside on an attached link and
those destinations that it can reach only through a router.

• Parameter discovery—How a node learns various parameters (link parameters or Internet

parameters) that it places in outgoing packets.

• Address resolution—How a node uses only a destination IPv6 address to determine a link-layer
address for destinations on an attached link.

• Next-hop determination—The algorithm that a node uses for mapping an IPv6 destination address
into a neighbor IPv6 address (either the next router hop or the destination itself) to which it plans
to send traffic for the destination.

• Neighbor unreachability detection—How a node determines that it can no longer reach a

neighbor.

• Duplicate address detection—How a node determines whether an address is already in use by

another node.

• Internet Control Message Protocol v6 (ICMPv6)

 37

ICMP sends error messages and information messages related to IP operations. ICMPv6 defines
additional error messages and informational messages specific to IPv6.

There are four different ICMPv6 error messages:

• Destination Unreachable—A packet cannot be delivered due to an inherent problem with how it is
being sent. Includes a code that indicates the nature of the problem that caused the packet not to
be delivered

• Packet Too Big—Sent when a packet is too large to be delivered.

• Time Exceeded—A packet cannot be delivered because it has exceeded the hop count specified in
the basic header hop-by-hop field.

• Parameter Problem—Indicates a problem with a field in the IPv6 header or extension headers that
makes it impossible to process the packet.

ICMPv6 information messages are used for sharing the information required to implement various
test, diagnostic, and support functions that are critical to the operation of IPv6. There are a total of
eight different ICMPv6 informational messages:

• Echo Request—

• Echo Reply—

• Router Advertisement—

• Router Solicitation—

• Neighbor Advertisement—

• Neighbor Solicitation—

• Redirect—

• Router Renumbering—

• Static routes for IPv6

Routing information can be configured statically. Whenever a route is configured statically, the
routing information base (RIB) is updated with routes specified through the static route. These routes
should be configured statically in the “routing-options” hierarchy. The following configuration is used
for enabling static routes for IPv6:

interfaces {
fe/0/1/0 {
unit 0 {
family inet6 {
 38

address fec0:0:0:3::1/64;
}
}
}
}
routing-options {
rib inet6.0 {
static {
route fec0:0:0:4::/64 next-hop fec0:0:0:3::ffff;
}
}
}

user@router> show route table inet6.0

inet6.0: 3 destination, 3 routes (3 active, 0 holddown, 0 hidden)
+ = Active Route, - = Last Active, * = Both
fec0:0:0:3::/64 *[Direct/0] 00:01:34
> via fe-0/1/0.0
fec:0:0:0:3::1/128 *[Local/0] 00:01:34
Local
fec0:0:0:4::/64 *[Static/5] 00:01:34
> to fec0:0:03:ffff via fe-0/1/0.0

RELATED DOCUMENTATION

IPv6 Overview | 21
Understanding Dual Stacking of IPv4 and IPv6 Unicast Addresses
IS-IS Overview
OSPF Overview
ICMP Router Discovery Overview
MPLS Overview for ACX Series Universal Metro Routers
Configure Path MTU Discovery
IPv6 Neighbor Discovery Overview
2 PART

Monitoring and Troubleshooting

Monitoring Networks | 40

Troubleshooting Network Issues | 47

Knowledge Base | 57
 40

CHAPTER 3

Monitoring Networks

IN THIS CHAPTER

Example: Tracing Global Routing Protocol Operations | 40

Example: Tracing Global Routing Protocol Operations

IN THIS SECTION

Requirements | 40

Overview | 40

Configuration | 41

Verification | 46

This example shows how to list and view files that are created when you enable global routing trace
operations.

Requirements
You must have the view privilege.

Overview

To configure global routing protocol tracing, include the traceoptions statement at the [edit routing-
options] hierarchy level:

traceoptions {
file filename <files number> <size size> <world-readable | no-world-readable>;
 41

flag flag <disable>;

}

The flags in a traceoptions flag statement are identifiers. When you use the set command to configure a
flag, any flags that might already be set are not modified. In the following example, setting the timer
tracing flag has no effect on the already configured task flag. Use the delete command to delete a
particular flag.

[edit routing-options traceoptions]

user@host# show
flag task;
user@host# set traceoptions flag timer
user@host# show
flag task;
flag timer;
user@host# delete traceoptions flag task
user@host# show
flag timer;

This example shows how to configure and view a trace file that tracks changes in the routing table. The
steps can be adapted to apply to trace operations for any Junos OS hierarchy level that supports trace
operations.

TIP: To view a list of hierarchy levels that support tracing operations, enter the help apropos
traceoptions command in configuration mode.

Configuration

IN THIS SECTION

CLI Quick Configuration | 42

Configuring Trace Operations | 42

Viewing the Trace File | 43

Results | 45
 42

CLI Quick Configuration

To quickly configure this example, copy the following commands, paste them into a text file, remove any
line breaks, change any details necessary to match your network configuration, and then copy and paste
the commands into the CLI at the [edit] hierarchy level.

set routing-options traceoptions file routing-table-changes

set routing-options traceoptions file size 10m
set routing-options traceoptions file files 10
set routing-options traceoptions flag route
set routing-options static route 1.1.1.2/32 next-hop 10.0.45.6

Configuring Trace Operations

Step-by-Step Procedure

The following example requires you to navigate various levels in the configuration hierarchy. For
information about navigating the CLI, see Using the CLI Editor in Configuration Mode in the Junos OS
CLI User Guide.

To configure the trace operations:

1. Configure trace operations.

[edit routing-options traceoptions]

user@host# set file routing-table-changes
user@host# set file size 10m
user@host# set file files 10
user@host# set flag route

2. Configure a static route to cause a change in the routing table.

[edit routing-options static]

user@host# set route 1.1.1.2/32 next-hop 10.0.45.6

3. If you are done configuring the device, commit the configuration.

[edit]
user@host# commit
 43

Viewing the Trace File

Step-by-Step Procedure

To view the trace file:

1. In operational mode, list the log files on the system.

user@host> file list /var/log

/var/log:
...
routing-table-changes
...

2. View the contents of the routing-table-changes file.

user@host> file show /var/log/routing-table-changes

Dec 15 11:09:29 trace_on: Tracing to "/var/log/routing-table-changes" started
Dec 15 11:09:29.496507
Dec 15 11:09:29.496507 Tracing flags enabled: route
Dec 15 11:09:29.496507
Dec 15 11:09:29.533203 inet_routerid_notify: Router ID: 192.168.4.1
Dec 15 11:09:29.533334 inet_routerid_notify: No Router ID assigned
Dec 15 11:09:29.533381 inet_routerid_notify: No Router ID assigned
Dec 15 11:09:29.533420 inet_routerid_notify: No Router ID assigned
Dec 15 11:09:29.534915 inet_routerid_notify: Router ID: 192.168.4.1
Dec 15 11:09:29.542934 inet_routerid_notify: No Router ID assigned
Dec 15 11:09:29.549253 inet_routerid_notify: No Router ID assigned
Dec 15 11:09:29.556878 inet_routerid_notify: No Router ID assigned
Dec 15 11:09:29.582990 rt_static_reinit: examined 3 static nexthops, 0 unreferenced
Dec 15 11:09:29.589920
Dec 15 11:09:29.589920 task_reconfigure reinitializing done
...

3. Filter the output of the log file.

user@host> file show /var/log/routing-table-changes | match 1.1.1.2

Dec 15 11:15:30.780314 ADD 1.1.1.2/32 nhid 0 gw 10.0.45.6 Static pref
5/0 metric at-0/2/0.0 <ctive Int Ext>
 44

Dec 15 11:15:30.782276 KRT Request: send len 216 v104 seq 0 ADD route/user af 2 table 0 infot
0 addr 1.1.1.2 nhop-type unicast nhindex 663

4. View the tracing operations in real time by running the monitor start command with an optional match
condition.

user@host> monitor start routing-table-changes | match 1.1.1.2

Aug 10 19:21:40.773467 BGP RECV 0.0.0.0/0
Aug 10 19:21:40.773685 bgp_rcv_nlri: 0.0.0.0/0
Aug 10 19:21:40.773778 bgp_rcv_nlri: 0.0.0.0/0 belongs to meshgroup
Aug 10 19:21:40.773832 bgp_rcv_nlri: 0.0.0.0/0 qualified bnp->ribact 0x0 l2afcb 0x0

5. Deactivate the static route.

user@host# deactivate routing-options static route 1.1.1.2/32

user@host# commit

*** routing-table-changes ***

Dec 15 11:42:59.355557 CHANGE 1.1.1.2/32 nhid 663 gw 10.0.45.6 Static pref
5/0 metric at-0/2/0.0 <Delete Int Ext>
Dec 15 11:42:59.426887 KRT Request: send len 216 v104 seq 0 DELETE route/user af 2 table 0
infot 0 addr 1.1.1.2 nhop-type discard filtidx 0
Dec 15 11:42:59.427366 RELEASE 1.1.1.2/32 nhid 663 gw 10.0.45.6 Static pref
5/0 metric at-0/2/0.0 <Release Delete Int Ext>

6. Halt the monitor command by pressing Enter and typing monitor stop.

[Enter]
user@host> monitor stop

7. When you are finished troubleshooting, consider deactivating trace logging to avoid any unnecessary
impact to system resources.
 45

When configuration is deactivated, it appears in the configuration with the inactive tag.

[edit routing-options]
user@host# deactivate traceoptions
user@host# commit

[edit routing-options]
user@host# show

inactive: traceoptions {
file routing-table-changes size 10m files 10;
flag route;
}
static {
inactive: route 1.1.1.2/32 next-hop 10.0.45.6;
}

8. To reactivate trace operations, use the activate configuration-mode statement.

[edit routing-options]
user@host# activate traceoptions
user@host# commit

Results

From configuration mode, confirm your configuration by entering the show routing-options command. If
the output does not display the intended configuration, repeat the instructions in this example to
correct the configuration.

user@host# show routing-options

traceoptions {
file routing-table-changes size 10m files 10;
flag route;
}
static {
route 1.1.1.2/32 next-hop 10.0.45.6;
}
 46

Verification

IN THIS SECTION

Verifying That the Trace Log File Is Operating | 46

Confirm that the configuration is working properly.

Verifying That the Trace Log File Is Operating

Purpose

Make sure that events are being written to the log file.

Action

user@host> show log routing-table-changes

Dec 15 11:09:29 trace_on: Tracing to "/var/log/routing-table-changes" started
 47

CHAPTER 4

Troubleshooting Network Issues

IN THIS CHAPTER

Working with Problems on Your Network | 47

Isolating a Broken Network Connection | 48

Identifying the Symptoms of a Broken Network Connection | 50

Isolating the Causes of a Network Problem | 52

Taking Appropriate Action for Resolving the Network Problem | 53

Evaluating the Solution to Check Whether the Network Problem Is Resolved | 55

Working with Problems on Your Network

IN THIS SECTION

Problem | 47

Solution | 48

Problem

Description

This checklist provides links to troubleshooting basics, an example network, and includes a summary of
the commands you might use to diagnose problems with the router and network.
 48

Solution

Table 4: Checklist for Working with Problems on Your Network

Tasks Command or Action

Isolating a Broken Network Connection

1. Identifying the Symptoms of a Broken Network ping (ip-address | hostname) show route (ip-address
Connection | hostname) traceroute (ip-address | hostname)

1. Isolating the Causes of a Network Problem show < configuration | interfaces | protocols |
route >

1. Taking Appropriate Action for Resolving the Network [edit] delete routing options static route
Problem destination-prefix commit and-quit show route
destination-prefix

1. Evaluating the Solution to Check Whether the Network show route (ip-address | hostname) ping (ip-address
Problem Is Resolved | hostname) count 3 traceroute (ip-address |
hostname)

Isolating a Broken Network Connection

By applying the standard four-step process illustrated in Figure 8 on page 48, you can isolate a failed
node in the network. Note that the functionality described in this section is not supported in versions
15.1X49, 15.1X49-D30, or 15.1X49-D40.

Figure 8: Process for Diagnosing Problems in Your Network

 49

Before you embark on the four-step process, however, it is important that you are prepared for the
inevitable problems that occur on all networks. While you might find a solution to a problem by simply
trying a variety of actions, you can reach an appropriate solution more quickly if you are systematic in
your approach to the maintenance and monitoring of your network. To prepare for problems on your
network, understand how the network functions under normal conditions, have records of baseline
network activity, and carefully observe the behavior of your network during a problem situation.

Figure 9 on page 49 shows the network topology used in this topic to illustrate the process of
diagnosing problems in a network.

Figure 9: Network with a Problem

The network in Figure 9 on page 49 consists of two autonomous systems (ASs). AS 65001 includes two
routers, and AS 65002 includes three routers. The border router (R1) in AS 65001 announces aggregated
prefixes 100.100/24 to the AS 65002 network. The problem in this network is that R6 does not have access
to R5 because of a loop between R2 and R6.

To isolate a failed connection in your network, follow the steps in these topics:

• Isolating the Causes of a Network Problem

 50

• Taking Appropriate Action for Resolving the Network Problem

• Taking Appropriate Action for Resolving the Network Problem

• Evaluating the Solution to Check Whether the Network Problem Is Resolved

Identifying the Symptoms of a Broken Network Connection

IN THIS SECTION

Problem | 50

Solution | 50

Problem

Description

The symptoms of a problem in your network are usually quite obvious, such as the failure to reach a
remote host.

Solution

To identify the symptoms of a problem on your network, start at one end of your network and follow
the routes to the other end, entering all or one of the following Junos OS command-line interfaces (CLI)
operational mode commands:

user@host> ping (ip-address | host-name)

user@host> show route (ip-address | host-name)
user@host> traceroute (ip-address | host-name)

Sample Output

user@R6> ping 10.0.0.5

PING 10.0.0.5 (10.0.0.5): 56 data bytes
36 bytes from 10.1.26.1: Time to live exceeded
Vr HL TOS Len ID Flg off TTL Pro cks Src Dst
 51

4 5 00 0054 e2db 0 0000 01 01 a8c6 10.1.26.2 10.0.0.5

36 bytes from 10.1.26.1: Time to live exceeded

Vr HL TOS Len ID Flg off TTL Pro cks Src Dst
4 5 00 0054 e2de 0 0000 01 01 a8c3 10.1.26.2 10.0.0.5

36 bytes from 10.1.26.1: Time to live exceeded

Vr HL TOS Len ID Flg off TTL Pro cks Src Dst
4 5 00 0054 e2e2 0 0000 01 01 a8bf 10.1.26.2 10.0.0.5

^C
--- 10.0.0.5 ping statistics ---
3 packets transmitted, 0 packets received, 100% packet loss

user@R6> show route 10.0.0.5

inet.0: 20 destinations, 20 routes (20 active, 0 holddown, 0 hidden)

+ = Active Route, - = Last Active, * = Both

10.0.0.5/32 *[IS-IS/165] 00:02:39, metric 10

> to 10.1.26.1 via so-0/0/2.0

user@R6> traceroute 10.0.0.5

traceroute to 10.0.0.5 (10.0.0.5), 30 hops max, 40 byte packets
1 10.1.26.1 (10.1.26.1) 0.649 ms 0.521 ms 0.490 ms
2 10.1.26.2 (10.1.26.2) 0.521 ms 0.537 ms 0.507 ms
3 10.1.26.1 (10.1.26.1) 0.523 ms 0.536 ms 0.514 ms
4 10.1.26.2 (10.1.26.2) 0.528 ms 0.551 ms 0.523 ms
5 10.1.26.1 (10.1.26.1) 0.531 ms 0.550 ms 0.524 ms

Meaning

The sample output shows an unsuccessful ping command in which the packets are being rejected
because the time to live is exceeded. The output for the show route command shows the interface
(10.1.26.1) that you can examine further for possible problems. The traceroute command shows the loop
between 10.1.26.1 (R2) and 10.1.26.2 (R6), as indicated by the continuous repetition of the two interface
addresses.
 52

Isolating the Causes of a Network Problem

IN THIS SECTION

Problem | 52

Solution | 52

Problem

Description

A particular symptom can be the result of one or more causes. Narrow down the focus of your search to
find each individual cause of the unwanted behavior.

Solution

To isolate the cause of a particular problem, enter one or all of the following Junos OS CLI operational
mode command:

user@host> show < configuration | bgp | interfaces | isis | ospf | route

>

Your particular problem may require the use of more than just the commands listed above. See the
appropriate command reference for a more exhaustive list of commonly used operational mode
commands.

Sample Output

user@R6> show interfaces terse

Interface Admin Link Proto Local Remote
so-0/0/0 up up
so-0/0/0.0 up up inet 10.1.56.2/30
iso
so-0/0/2 up up
so-0/0/2.0 up up inet 10.1.26.2/30
iso
so-0/0/3 up up
 53

so-0/0/3.0 up up inet 10.1.36.2/30

iso
[...Output truncated...]

The following sample output is from R2:

user@R2> show route 10.0.0.5

inet.0: 22 destinations, 25 routes (22 active, 0 holddown, 0 hidden)

+ = Active Route, - = Last Active, * = Both

10.0.0.5/32 *[Static/5] 00:16:21

> to 10.1.26.2 via so-0/0/2.0
[BGP/170] 3d 20:23:35, MED 5, localpref 100
AS path: 65001 I
> to 10.1.12.1 via so-0/0/0.0

Meaning

The sample output shows that all interfaces on R6 are up. The output from R2 shows that a static route
[Static/5] configured on R2 points to R6 (10.1.26.2) and is the preferred route to R5 because of its low
preference value. However, the route is looping from R2 to R6, as indicated by the missing reference to R5
(10.1.15.2).

Taking Appropriate Action for Resolving the Network Problem

IN THIS SECTION

Problem | 54

Solution | 54
 54

Problem

Description

The appropriate action depends on the type of problem you have isolated. In this example, a static route
configured on R2 is deleted from the [routing-options] hierarchy level. Other appropriate actions might
include the following:

Solution

• Check the local router’s configuration and edit it if appropriate.

• Troubleshoot the intermediate router.

• Check the remote host configuration and edit it if appropriate.

• Troubleshoot routing protocols.

• Identify additional possible causes.

To resolve the problem in this example, enter the following Junos OS CLI commands:

[edit]
user@R2# delete routing-options static route destination-
prefix
user@R2# commit and-quit
user@R2# show route destination-prefix

Sample Output

[edit]
user@R2# delete routing-options static route 10.0.0.5/32

[edit]
user@R2# commit and-quit
commit complete
Exiting configuration mode

user@R2> show route 10.0.0.5

inet.0: 22 destinations, 24 routes (22 active, 0 holddown, 0 hidden)

+ = Active Route, - = Last Active, * = Both
 55

10.0.0.5/32 *[BGP/170] 3d 20:26:17, MED 5, localpref 100

AS path: 65001 I
> to 10.1.12.1 via so-0/0/0.0

Meaning

The sample output shows the static route deleted from the [routing-options] hierarchy and the new
configuration committed. The output for the show route command now shows the BGP route as the
preferred route, as indicated by the asterisk (*).

Evaluating the Solution to Check Whether the Network Problem Is

Resolved

IN THIS SECTION

Problem | 55

Solution | 56

Problem

Description

If the problem is solved, you are finished. If the problem remains or a new problem is identified, start the
process over again.

You can address possible causes in any order. In relation to the network in Isolating a Broken Network
Connection, we chose to work from the local router toward the remote router, but you might start at a
different point, particularly if you have reason to believe that the problem is related to a known issue,
such as a recent change in configuration.
 56

Solution

To evaluate the solution, enter the following Junos OS CLI commands:

user@host> show route (ip-address |host-name)

user@host> ping (ip-address | host-name)
user@host> traceroute (ip-address | host-name)

Sample Output

user@R6> show route 10.0.0.5

inet.0: 20 destinations, 20 routes (20 active, 0 holddown, 0 hidden)

+ = Active Route, - = Last Active, * = Both

10.0.0.5/32 *[BGP/170] 00:01:35, MED 5, localpref 100, from 10.0.0.2

AS path: 65001 I
> to 10.1.26.1 via so-0/0/2.0

user@R6> ping 10.0.0.5

PING 10.0.0.5 (10.0.0.5): 56 data bytes
64 bytes from 10.0.0.5: icmp_seq=0 ttl=253 time=0.866 ms
64 bytes from 10.0.0.5: icmp_seq=1 ttl=253 time=0.837 ms
64 bytes from 10.0.0.5: icmp_seq=2 ttl=253 time=0.796 ms
^C
--- 10.0.0.5 ping statistics ---
3 packets transmitted, 3 packets received, 0% packet loss
round-trip min/avg/max/stddev = 0.796/0.833/0.866/0.029 ms

user@R6> traceroute 10.0.0.5

traceroute to 10.0.0.5 (10.0.0.5), 30 hops max, 40 byte packets
1 10.1.26.1 (10.1.26.1) 0.629 ms 0.538 ms 0.497 ms
2 10.1.12.1 (10.1.12.1) 0.534 ms 0.538 ms 0.510 ms
3 10.0.0.5 (10.0.0.5) 0.776 ms 0.705 ms 0.672 ms

Meaning

The sample output shows that there is now a connection between R6 and R5. The show route command
shows that the BGP route to R5 is preferred, as indicated by the asterisk (*). The ping command is
successful and the traceroute command shows that the path from R6 to R5 is through R2 (10.1.26.1), and
then through R1 (10.1.12.1).
 57

CHAPTER 5

Knowledge Base
3 PART

Configuration Statements and

Operational Commands

Configuration Statements | 59

Operational Commands | 60
 59

CHAPTER 6

Configuration Statements
 60

CHAPTER 7

Operational Commands

IN THIS CHAPTER

show | display rfc5952 | 60

show | display rfc5952

IN THIS SECTION

Syntax | 60

Description | 60

Required Privilege Level | 60

Sample Output | 61

Release Information | 61

Syntax

show | display rfc5952

Description

Display IPv6 addresses as per RFC 5952 specifications. For RFC information, go to: http://tools.ietf.org/
html/rfc5952.

Required Privilege Level

View
 61

Sample Output

command-name

user@host> show configuration interfaces ge-0/0/0 |display rfc5952

unit 0 {
family inet6 {
address 2012::2:1/64;
address 2001::1111:2222:0:0:1/96;
}
}

Release Information

Command introduced before Junos OS Release 11.4.

RELATED DOCUMENTATION

show