Hinge Products

Hinges & Brackets Bush Options

The choice of hinges, brackets and associated parts depends on end frame and door design and
the test requirements for end wall and racking loads.

We will be pleased to give detailed advice, but the following points should be considered:

• Forged steel door hinges can usually only be welded to the doors
• Finish, self colour, zinc plated or galvanised are available*
• Nylon (A), (B) & (D) or phosphor bronze (C) bushes are available*
• Bolt-on brackets and hinges can be fitted after final painting
• If repairs are necessary, removal or replacement of bolt-on brackets and hinges is simple
• Flat back design forged steel door hinges are not recommended for use on offshore
container main doors
• Customer logos are available subject to minimum order quantities*. No logo (O) is standard
Seal-Groove Hinges
• Grease nipples ( N or NSS) can only be fitted to our range of forged hinges (see illustration
• Gives greater hinge life
for fitting positions). Other positions available on request
• Sealant forms barrier across unwelded part of hinge (dependent upon the design)
• Bloxwich recommend Ø12.7 pins or 1/2” bolts are used for Ø12.7 bushes, however if
• Prevents corrosion by stopping ingress of water behind hinge
increased clearance is required Ø12 pins or M12 bolts can be fitted*
• Sealant easily applied by conventional sealant gun
• For more information and dimensions please visit https://www.bloxwichdoorgear.com
• Prevents rust streaks (as found with conventional hinges ) from forming on doors
• Seal-groove provides visual proof that the hinge has been sealed over total width
*Selected hinges only #Subject to quantity and lead time

Oil Hole/Grease Nipple Positions

56 57
Tel: +44 (0)1543 435 160 Fax: +44 (0)1543 469 610 Web: www.bloxwichgroup.com Email: [email protected] [email protected] [email protected]
 Hinge Products

Bloxwich Hinge Pin Arrangements Model No. BCP1032-001 (Mild Steel)

Below are various hinge pin arrangements showing common configurations. Other configurations
Model No. BCP1032-002 (Mild Steel)
are available, we will be pleased to give detailed advice, but the following points should be
considered: Model No. BCP1054-001 (Aluminium)
Forged Door Hinge 83/91mm
• The below are only recommendations and the racking and door burst capabilities of the
Supplied in: Self colour
vehicle or unit must be established by the designer. Hinge brackets or butts shown are for
illustration purposes only. Use: Weld on hinge, to suit Ø12 hinge pin or M12
• Bloxwich recommend the fitment of grease nipples and regular inspection and maintenance bolt or Ø12.7 hinge pin or 1/2” bolt or Ø15 hinge
pin or 5/8” bolt. See table for details
of hinge components in service.
• Made by Bloxwich in accordance with our design standards, copyrights, trademarks and Can be used with Bloxwich standard or special
patents. hinge butts or the BCP1037/010 or BCP1037/003
forged steel gudgeons
• When required Bloxwich provide certificates to 2.2 according to EN10204. When required
Bloxwich will provide test results by an independent UK test house as per table of requirements Weight: See table
3-6 of DNV 2.7-1 (2013).

Part No A B C D E Weight Bush

BCP1032-001 12.7 83 40 76.2 44.5 520 g N/A

BCP1032-002 16 83 38 76.2 44.5 500 g N/A

Zinc plated steel

BCP1054-001 12.7 91 42 102 57 270 g
bush

58 59
Tel: +44 (0)1543 435 160 Fax: +44 (0)1543 469 610 Web: www.bloxwichgroup.com Email: [email protected] [email protected] [email protected]
 Hinge Products

Model No. BCP11027 (Mild Steel) Model No. BCP13993 (Mild Steel)
Forged Steel Door Hinge 111mm Forged Steel Door Hinge 115mm
Supplied in: Self colour or zinc plated Supplied in: Self colour or zinc plated

Use: Weld on hinge, bushed to suit Ø12.7 hinge pin Use: Weld on hinge, un-bushed Ø15 or bushed
or 1/2” bolt. See table for options to suit Ø12.7 hinge pin or 1/2” bolt. See table for
options
Weight: 860 g
Weight: 475 g

Finish * Bush No. * Oil Hole/Grease Nipple Position * Nipple * Finish * Bush No. * Oil Hole/Grease Nipple Position * Nipple *
None
None Un- None
Self Colour S BCP 10040 A Vertical 1 Self Colour S bushed None

Horizontal 2 BCP 12595

BCP 12595
N N
Mild Steel BCP 10040 A Mild Steel
45º 3

Zinc Z BCP 12119 C 135º 4 BCSP 12595 Zinc Z Vertical 1 BCSP 12595
Stainless NSS BCP 12119 C Stainless NSS
180º 5 Steel Steel

*When ordering, please add the above ‘characters’ to the part number to indicate required *When ordering, please add the above ‘characters’ to the part number to indicate required
condition, e.g. BCP11027SA1N indicates self colour with BCP10040 bush, vertical oil hole and condition, e.g. BCP13993SA1N indicates self colour with BCP10040 bush, vertical oil hole and
BCP12595 mild steel grease nipple. BCP12595 mild steel grease nipple.

Please refer to the oil hole/grease nipple positions and bush options illustrations at the beginning Please refer to the oil hole/grease nipple positions and bush options illustrations at the beginning
of the section for more information. of the section for more information.

60 61
Tel: +44 (0)1543 435 160 Fax: +44 (0)1543 469 610 Web: www.bloxwichgroup.com Email: [email protected] [email protected] [email protected]
 Hinge Products

Model No. BCP11026 (Mild Steel) Model No. BCP11026DM (Mild Steel)
Model No. BCSP11026#(Stainless Steel) Forged Steel Door Hinge 130mm
Forged Steel Door Hinge 130mm Supplied in: Self colour or zinc plated

Supplied in: Self colour or zinc plated Use: Weld on flat back design, bushed to suit Ø12.7
hinge pin or 1/2” bolt.
Use: Weld on hinge, bushed to suit Ø12.7 hinge pin
or 1/2” bolt. See table for options Not recommended for use on offshore container
main doors. See table for options
Weight: 940 g
Weight: 940 g
#Subject to quantity and lead time

Finish * Bush No. * Oil Hole/Grease Nipple Position * Nipple * Finish * Bush No. * Oil Hole/Grease Nipple Position * Nipple *
None None
None None
Self Colour S BCP 10040 A Vertical 1 Self Colour S BCP 10040 A Vertical 1
Horizontal 2 Horizontal 2
BCP 12595 BCP 12595
N N
45º 3 Mild Steel 45º 3 Mild Steel

Zinc Z BCP 12119 C 135º 4 BCSP 12595 Zinc Z BCP 12119 C 135º 4 BCSP 12595
Stainless NSS Stainless NSS
180º 5 Steel 180º 5 Steel

*When ordering, please add the above ‘characters’ to the part number to indicate required *When ordering, please add the above ‘characters’ to the part number to indicate required
condition, e.g. BCP11026SA1N indicates self colour with BCP10040 bush, vertical oil hole and condition, e.g. BCP11026DMSA1N indicates self colour with BCP10040 bush, vertical oil hole and
BCP12595 mild steel grease nipple. BCP12595 mild steel grease nipple.

Please refer to the oil hole/grease nipple positions and bush options illustrations at the beginning Please refer to the oil hole/grease nipple positions and bush options illustrations at the beginning
of the section for more information. of the section for more information.

62 63
Tel: +44 (0)1543 435 160 Fax: +44 (0)1543 469 610 Web: www.bloxwichgroup.com Email: [email protected] [email protected] [email protected]
 Hinge Products

Model No. BCP11292 (Mild Steel) Model No. BCP10524 (Mild Steel)
Forged Steel Door Hinge 150mm Forged Steel Door Hinge 203mm
Supplied in: Self colour or zinc plated Supplied in: Self colour or zinc plated

Use: Weld on hinge, bushed to suit Ø12.7 hinge Use: Weld on hinge, bushed to suit Ø12.7 hinge pin
pin or 1/2” bolt. See table for options or 1/2” bolt. See table for options

Weight: 1.12 kg Weight: 1.25 kg

Finish * Bush No. * Oil Hole/Grease Nipple Position * Nipple * Finish * Bush No. * Oil Hole/Grease Nipple Position * Nipple *
None None
None None
Self Colour S BCP 10040 A Vertical 1 Self Colour S BCP 10040 A Vertical 1
Horizontal 2 Horizontal 2
BCP 12595 BCP 12595
N N
45º 3 Mild Steel Mild Steel
45º 3

Zinc Z BCP 12119 C 135º 4 BCSP 12595 Zinc Z BCP 12119 C 135º 4 BCSP 12595
Stainless NSS Stainless NSS
180º 5 Steel 180º 5 Steel

*When ordering, please add the above ‘characters’ to the part number to indicate required *When ordering, please add the above ‘characters’ to the part number to indicate required
condition, e.g. BCP11292SA1N indicates self colour with BCP10040 bush, vertical oil hole and condition, e.g. BCP10524SA1N indicates self colour with BCP10040 bush, vertical oil hole and
BCP12595 mild steel grease nipple. BCP12595 mild steel grease nipple.

Please refer to the oil hole/grease nipple positions and bush options illustrations at the beginning Please refer to the oil hole/grease nipple positions and bush options illustrations at the beginning
of the section for more information. of the section for more information.

64 65
Tel: +44 (0)1543 435 160 Fax: +44 (0)1543 469 610 Web: www.bloxwichgroup.com Email: [email protected] [email protected] [email protected]
 Hinge Products

Model No. BCP10524DM (Mild Steel) Model No. BCP10045 (Mild Steel)
Forged Steel Door Hinge 203mm Model No. BCSP10045# (Stainless Steel)
Supplied in: Self colour or zinc plated Forged Steel Door Hinge 305mm
Use: Weld on flat back design, bushed to suit Ø12.7 Supplied in: Self colour, zinc plated, galvanised
hinge pin or 1/2” bolt. or polyester

Not recommended for use on offshore container Use: Weld or bolt on hinge, bushed to suit Ø12.7
main doors. See table for options hinge pin or 1/2” bolt, Ø10.5 fixing holes. See
table for options
Weight: 1.25 kg
Weight: 1.58 kg

#Subject to quantity and lead time

Finish * Bush No. * Oil Hole/Grease Nipple Position * Nipple * Hole * Finish * Bush No. * Oil Hole/Grease Position * Nipple *
None None
None Self Colour S None
Self Colour S BCP 10040 A Vertical 1 BCP Vertical 1
A
10040
Horizontal 2 Zinc Z Horizontal 2
BCP 12595 BCP 12595
N 10.5 B N
45º 3 Mild Steel Mild Steel
45º 3
BCSP 12595 Galvanised G
Zinc Z BCP 12119 C 135º 4 BCP BCSP 12595
C 135º 4
Stainless NSS 12119 Stainless NSS
180º 5 Steel Polyester P 180° 5 Steel

*When ordering, please add the above ‘characters’ to the part number to indicate required *When ordering, please add the above ‘characters’ to the part number to indicate required
condition, e.g. BCP10524DMSA1N indicates self colour with BCP10040 bush, vertical oil hole and condition, e.g. BCP10045BZC1N indicates Ø10.5 fixing hole, zinc plated with BCP12119 bush,
BCP12595 mild steel grease nipple. vertical oil hole and BCP12595 mild steel grease nipple.

Please refer to the oil hole/grease nipple positions and bush options illustrations at the beginning Please refer to the oil hole/grease nipple positions and bush options illustrations at the beginning
of the section for more information. of the section for more information.

66 67
Tel: +44 (0)1543 435 160 Fax: +44 (0)1543 469 610 Web: www.bloxwichgroup.com Email: [email protected] [email protected] [email protected]
 Hinge Products

Model No. BCP1008-1 (Mild Steel) Model No. BCP12594 (Mild Steel)
Forged Steel Reverse Door Hinge 165mm Model No. BCSP12171 (Stainless Steel)
Supplied in: Self colour or zinc plated Pressed Hinge 295mm
Use: Weld on reverse hinge bushed, to suit Ø12.7 Supplied in: (Mild Steel only) self colour, zinc
hinge pin or 1/2” bolt. See table for options plated, galvanised or polyester and 304 stainless
steel
For use on sealed or unsealed lids or hatches,
reduces the overall height, can be used/ordered Use: Bolt on hinge, bushed to suit Ø12 hinge pin or
with the BCP 1008-2 hinge bracket M12 bolt or Ø12.7 hinge pin or 1/2” bolt or, Ø10.5
or Ø8.5 fixing holes. See table for options
Weight: 1.03 kg
Weight: 620 g

Finish * Bush No. * Oil Hole/Grease Nipple Position * Nipple * Hole Ø * Logo * Finish * Bush No. ID *
None No Logo O Self Colour S
None
Self Colour S BCP 10040 A Vertical 1 Zinc Z
10.5 B Customer logos are BCP 12456 12.0 D
Horizontal 2 available subject Galvanise G
BCP 12595
N to minimum order
45º 3 Mild Steel Polished V
quantities.
135º 4 BCSP 12595 8.5 A Polyester P BCP 12194 12.7 B
Zinc Z BCP 12119 C
Stainless NSS
180º 5 Steel
*When ordering, please add the above ‘characters’ to the part number to indicate required
condition, e.g. BCP12594BOZD indicates mild steel hinge, Ø10.5 fixing holes, no logo, zinc plated
with BCP12456 bush.
*When ordering, please add the above ‘characters’ to the part number to indicate required
condition, e.g. BCP1008-1SA1N indicates self colour with BCP10040 bush, vertical oil hole and
For stainless steel version please quote BCSP12171BOVD
BCP12595 mild steel grease nipple.

Please refer to the oil hole/grease nipple positions and bush options illustrations at the
beginning of the section for more information.

68 69
Tel: +44 (0)1543 435 160 Fax: +44 (0)1543 469 610 Web: www.bloxwichgroup.com Email: [email protected] [email protected] [email protected]
 Hinge Products

Model No. BCP15073 (Mild Steel) Model No. BCP13607 (Mild Steel)
Model No. BCSP15073 (Stainless Steel) Model No. BCSP13607 (Stainless Steel)
Pressed Hinge 295mm Pressed Hinge 312mm
Supplied in: (Mild Steel only) self colour, zinc Supplied in: (Mild Steel only) self colour,
plated, galvanised or polyester and 304 stainless zinc plated, galvanised or polyester and 304
steel stainless steel. See table for options

Use: Bolt on hinge, bushed to suit Ø12 hinge pin or Use: Bolt on hinge, bushed to suit Ø12 hinge
M12 bolt or Ø12.7 hinge pin or 1/2” bolt or, Ø10.5 pin or 1/2” bolt or, Ø10.5 or Ø8.5 fixing holes
or Ø8.5 fixing holes. See table for options
Weight: 765 g
Weight: 720 g

Hole Ø * Logo * Finish * Bush No. ID * Hole Ø * Logo * Finish * Bush No. ID *
No Logo O Self Colour S No Logo O Self Colour S

Zinc Z Zinc Z
10.5 B Customer logos are BCP 12456 12.0 D 10.5 B Customer logos are BCP 12456 12.0 D
available subject Galvanise G available subject Galvanise G
to minimum order Polished V to minimum order Polished V
quantities. quantities.
8.5 A Polyester P BCP 12194 12.7 B 8.5 A Polyester P BCP 12194 12.7 B

*When ordering, please add the above ‘characters’ to the part number to indicate required *When ordering, please add the above ‘characters’ to the part number to indicate required
condition, e.g. BCP15073BOZD indicates mild steel hinge, 10.5 Ø fixing holes, no logo, zinc plated condition, e.g. BCP13607BOZD indicates mild steel hinge, 10.5 Ø fixing holes, no logo, zinc plated
with BCP12456 bush. with BCP12456 bush.

For stainless steel version please quote BCSP15073BOVD For stainless steel version please quote BCSP13607BOVD

70 71
Tel: +44 (0)1543 435 160 Fax: +44 (0)1543 469 610 Web: www.bloxwichgroup.com Email: [email protected] [email protected] [email protected]
 Hinge Products

Model No. BCP12447 (Mild Steel) Model No. BCP (Mild Steel)
Model No. BCSP12447 (Stainless Steel) Forged Hinge Bolted Assemblies
Pressed Hinge 356mm Supplied in: Self colour

Supplied in: (Mild Steel only) self colour, Other combinations available on request please
zinc plated, galvanised or polyester and 304 contact us for further details
stainless steel
Use: For containers, parts supplied assembled
Use: Bushed to suit Ø12 hinge pin or M12 ready to weld in place
bolt or Ø12.7 hinge pin or 1/2” bolt, Ø10.5 or
Ø8.5 fixing holes. See table for options All combinations use the BCP15111 hinge butt,
BCSP15121 bolt, BCSP15133 flat washers,
Weight: 1.2 kg BCSP15128 castle nut, BCSP15127 cotter pin and
BCP12595 grease nipple fitted in position 5

Weight: See table

Hole Ø * Logo * Finish * Bush No. ID *
Model Hinge Handing “A” Weight
B4 No Logo O Self Colour S
BCP 15113 BCP11026SC5N LH 130 1.4 kg
10.5
B6 Zinc Z
BCP 12456 12.0 D BCP 15114 BCP11292SC5N LH 150 1.5 kg
Customer logos are
Galvanise G
available subject BCP 15115 BCP10524SC5N LH 203 1.7 kg
to minimum order
8.5 A6 quantities. Polished V
BCP 15117 BCP11026SC5N RH 130 1.4 kg
Polyester P BCP 12194 12.7 B
BCP 15118 BCP11292SC5N RH 150 1.5 kg

*When ordering, please add the above ‘characters’ to the part number to indicate required BCP 15119 BCP10524SC5N RH 203 1.7 kg
condition, e.g. BCP12447B4OZD indicates mild steel hinge, with four 10.5 Ø fixing holes, no logo,
zinc plated with BCP12456 bush.

For stainless steel version please quote BCSP12447BOVD

72 73
Tel: +44 (0)1543 435 160 Fax: +44 (0)1543 469 610 Web: www.bloxwichgroup.com Email: [email protected] [email protected] [email protected]
 Hinge Products

Model No. BCP (Mild Steel) Model No. BCP (Mild Steel)
Forged Hinge Welded Assemblies Model No. BCSP (Stainless Steel)
Supplied in: Self colour Pressed Hinge Assemblies
Other combinations, oil hole/grease nipple Supplied in: (Mild Steel only) self colour, zinc
positions and bush options available on request plated, galvanised or polyester and 304 stainless
please contact us for further details steel

Use: For containers, parts supplied assembled Other combinations available on request please
ready to weld in place contact us for further details

All combinations use the BCP15034 hinge butt, Use: Parts supplied in unassembled kits to make
BCSP-24001/82 hinge pin and BCP12595 grease ordering easier
nipple fitted in position 5
See the individual parts listed below for dimensions
Weight: See table
Weight: See table

Model Hinge “A” Weight Model Hinge Bracket Bolt/Pin Nut/E Clip “A” Weight

BCP14884SC5N BCP11027SC5N 111 1.25 kg BCP14242G BCP12594BOGD BCP14149 BCP12463 BCP12462 307 1.1 kg

BCP14467SC5N BCP11026SC5N 130 1.3 kg BCP14242Z BCP12594BOZD BCP14149 BCP12463 BCP12462 307 1.1 kg

BCP14883SC5N BCP11292SC5N 150 1.4 kg BCP15105 BCP15073BOZD BCP14149 BCP12463 BCP12462 297 1.1 kg

BCP14476SC5N BCP10524SC5N 203 1.6 kg BCP15108 BCP13607BOZD BCP15100 BCP12463 BCP12462 324 1.1 kg

BCP15109 BCP12447A6ZD BCP14149 BCP12463 BCP12462 368 1.2 kg

BCP15110 BCP12594BOZD BCP14149 BCP12463 BCP12462 307 1.1 kg

BCSP15105 BCSP15073BOVD BCSP14149 BCSP12463 BCSP12462 297 1.1 kg

BCSP15108 BCSP13607BOVD BCSP15100 BCSP12463 BCSP12462 324 1.1 kg

BCSP15109 BCSP12447A6OV2D BCSP14149 BCSP12463 BCSP12462 368 1.2 kg

BCSP15110 BCSP12171BOVD BCSP14149 BCSP12463 BCSP12462 307 1.1 kg

74 75
Tel: +44 (0)1543 435 160 Fax: +44 (0)1543 469 610 Web: www.bloxwichgroup.com Email: [email protected] [email protected] [email protected]
 Hinge Products

Model No. BCSP16014# (Stainless Steel) Model No. BCP16014 (Mild Steel)
Barrel Hinge Assembly Barrel Hinge Assembly 180mm
Supplied in: Electro polished finish Supplied in: Self colour

Use: Serviceable lift off* barrel hinge with grease nipple, Use: Serviceable lift off* barrel hinge with grease
fabricated and welded from 304 stainless steel. Length can nipple. *Depending upon mounting arrangement
be tailored to suit your designs. *Depending upon mounting
arrangement. #Subject to quantity and lead time Weight: 470 g

Weight: 625 g

Model No. BCSP14499# (Stainless Steel) Model No. BCP16015 (Mild Steel)
Barrel Hinge Assembly Model No. BCSP16015 (Stainless Steel)
Supplied in: Electro polished finish Barrel Hinge Assembly 100mm
Use: Serviceable lift off* barrel hinge with grease nipple, Supplied in: Self colour
fabricated and welded from 304 stainless steel. Length can
be tailored to suit your designs. *Depending upon mounting Use: Serviceable lift off* barrel hinge with grease nip-
arrangement. #Subject to quantity and lead time ple. *Depending upon mounting arrangement

Weight: 930 g Weight: 170 g

76 77
Tel: +44 (0)1543 435 160 Fax: +44 (0)1543 469 610 Web: www.bloxwichgroup.com Email: [email protected] [email protected] [email protected]
 Hinge Products

Model No. BCSP13302-AOV-MB Model No. BCSP13302-AOV-M

Hinge Assembly 95mm Hinge Assembly 190mm
Supplied in: 304 stainless steel electro-polished finish Supplied in: 304 stainless steel electro-polished
finish
Use: General purpose pressed stainless steel hinge assembly
Use: General purpose pressed stainless steel hinge
No hole, square hole and other Ø hole sizes avialable on assembly
request# please contact us for details
No hole, square hole and other Ø hole sizes
Weight: 440 g avialable on request# please contact us for details

Weight: 650 g

Model No. BCP13302BOZ (Mild Steel) Model No. BCP1008 (Mild Steel)
Model No. BCSP13302-BOV (Stainless Steel) Reverse Hinge Assembly 165mm
Hinge Assembly 185mm Supplied in: Self colour or zinc plated

Supplied in: Mild steel zinc plated or 304 stainless steel Use: On sealed or unsealed lids or hatches,
electro-polished finish reduces the overall height

Use: General purpose pressed mild steel or stainless steel Weight: 1.5 kg
hinge assembly

No hole, square hole and other Ø hole sizes avialable on

request# please contact us for details

Weight: 650 g

78 79
Tel: +44 (0)1543 435 160 Fax: +44 (0)1543 469 610 Web: www.bloxwichgroup.com Email: [email protected] [email protected] [email protected]
 Hinge Products

Model No. BCP13020Z (Mild Steel) Model No. BCP14149 (Mild Steel)
Cranked Hinge Assembly 463mm Model No. BCSP14149 (Stainless Steel)
Supplied in: Zinc plated finish as standard Hinge Bracket 63mm (Offset)
Supplied in: Mild steel self colour, zinc plated or galvanised and
Use: For rear doors where tail lifts are fitted
304 stainless steel
and doors are recessed into end frame
Use: Pivot hole size to suit M12 bolt or Ø12 hinge pin or /2
Weight 3.3 kg
version suits 1/2” bolt or Ø12.7 hinge pin. Replaces fabricated
BCP12228 hinge bracket

Weight: 290 g

Model No. BCP1008-2 (Mild Steel) Model No. BCP15100 (Mild Steel)
Hinge Bracket Model No. BCSP15100 (Stainless Steel)
Supplied in: Self colour, zinc plated or galvanized Hinge Bracket 74mm (Offset)
Supplied in: Mild steel self colour, zinc plated or galvanised and
Use: With the BCP1008-1 reverse hinge on sealed or 304 stainless steel
unsealed lids or hatches, reduces the overall height
Use: Pivot hole size to suit M12 bolt or Ø12 hinge pin
Weight: 300 g
Weight: 290 g

80 81
Tel: +44 (0)1543 435 160 Fax: +44 (0)1543 469 610 Web: www.bloxwichgroup.com Email: [email protected] [email protected] [email protected]
 Hinge Products

Model No. BCP13608B (Mild Steel) Model No. BCP11354 (Mild Steel)
Model No. BCSP13608B (Stainless Steel) Model No. BCSP11354#(Stainless Steel)
Hinge Bracket 74mm Hinge Butt (standard)
Supplied in: Mild steel self colour, zinc plated or galvanised and Supplied in: Self colour
304 stainless steel
Use: On with all Bloxwich hinges, commonly used on
Use: Pivot hole size to suit M12 bolt or Ø12 hinge pin. containers. Other sizes available on request. #Subject to
quantity and lead time
Weight: 230 g
Weight: 114 g

Model No. BCP12459 (Mild Steel) Model No. BCP15111 (Mild Steel)
Hinge Bracket 64mm (Offset) Model No. BCSP15111#(Stainless Steel)
Supplied in: Self colour, zinc plated or galvanised Hinge Butt (special)
Supplied in: Self colour
Use: /1 pivot hole size to suit M12 bolt or Ø12 hinge pin or /2
version suits 1/2” bolt or Ø12.7 hinge pin.
Use: On all Bloxwich hinges,gives increased clearance for
bolting when required. Other sizes available on request.
Weight: 170 g
#Subject to quantity and lead time

Weight: 120 g

82 83
Tel: +44 (0)1543 435 160 Fax: +44 (0)1543 469 610 Web: www.bloxwichgroup.com Email: [email protected] [email protected] [email protected]
 Hinge Products

Model No. BCSP Model No. BCSP14164

Hinge Pins E Clip
Supplied in: 304 stainless steel Supplied in: 304 stainless steel
except BCSP12272/94 which
is 316 stainless steel. Use: With Bloxwich hinge pins BCSP12225/94, BCSP
Other pins available, please 14163, BCSP12273/94 and BCSP24001/92
contact us for details
Weight: 1 g
Use: With Bloxwich hinges, butts and brackets Average Weight: 90 g

Model No. BCSP12336

Hinge Pin Collar
Supplied in: 304 stainless steel

Use: With Bloxwich uncrimped hinge pins, /20 hole

size to suit Ø12 hinge pin or M/20 version suits Ø12.7
hinge pin

Weight: 13 g

84 85
Tel: +44 (0)1543 435 160 Fax: +44 (0)1543 469 610 Web: www.bloxwichgroup.com Email: [email protected] [email protected] [email protected]
 Hinge Products

Model No. BCP12463 (Zinc Plated) Model No. BCSP15121

Model No. BCSP12463 (Stainless Steel) ½”-13 UNC Bolt
M12 Bolt Supplied in: 304 stainless steel
Supplied in: Mild steel zinc plated or 304 stainless steel Use: With Bloxwich hinges, butts and brackets. Hole
position drilled to order (if required). Can be used
Use: With Bloxwich hinges, butts and brackets with 1/2”-13 UNC castle and cotter pin to lock the pin
securely but also allows easy removal for mainte-
Weight: 96 g nance.

Weight: 134 g

Model No. BCP12462 (Zinc Plated) Model No. BCSP15133

Model No. BCSP12462 (Stainless Steel) ½” UNC Flat Washer
M12 Nyloc Nut Supplied in: 304 stainless steel
Supplied in: Mild steel zinc plated or 304 stainless steel
Use: With Bloxwich hinges, butts and brackets.
Use: With Bloxwich hinges, butts and brackets
Reduces paintwork damage on assembly.
Weight: 10 g
Weight: 3 g

86 87
Tel: +44 (0)1543 435 160 Fax: +44 (0)1543 469 610 Web: www.bloxwichgroup.com Email: [email protected] [email protected] [email protected]
 Engineering Services

Model No. BCSP15128 Combining SolidWorks Professional, Visualise, Composer, Adobe

Photoshop and InDesign software etc with decades of experi-
½”-13 UNC Castle Nut ence in DNV & ISO container design, test and manufacture we
Supplied in: 304 stainless steel can create designs, drawings, animations, user manuals and
Use: With Bloxwich hinges, butts and brackets. Can be used carry out consultancy work.
with 1/2”-13 UNC bolt and cotter pin to lock the pin securely
but also allows easy removal for maintenance.
For more information please see www.bloxwichtrading.com , call
+44 (0)1543 435 160 or email [email protected]
Weight: 20 g

Model No. BCSP 15127

Ø2.5 x 25 Cotter Pin
Supplied in: 304 stainless steel

Use: With Bloxwich hinges, butts and brackets. Can

be used with 1/2” UNC bolt and castle nut to lock
the pin securely but also allows easy removal for
maintenance.

Weight: 1 g

25 2.5
5

88
Tel: +44 (0)1543 435 160 Fax: +44 (0)1543 469 610 Web: www.bloxwichgroup.com