Scribd
Upload
12 views

Thyristor

A thyristor is a four-layer semiconductor device made of alternating P-type and N-type materials that has three electrodes: an anode, cathode, and gate. The most common type is the silicon-controlled rectifier (SCR) which conducts current when a pulse is applied to the gate until the voltage is reversed or drops below a threshold. Thyristors can be fully on or off unlike transistors which operate between on and off states.

Uploaded by

genesisjohnhleysa
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
12 views

Thyristor

A thyristor is a four-layer semiconductor device made of alternating P-type and N-type materials that has three electrodes: an anode, cathode, and gate. The most common type is the silicon-controlled rectifier (SCR) which conducts current when a pulse is applied to the gate until the voltage is reversed or drops below a threshold. Thyristors can be fully on or off unlike transistors which operate between on and off states.

Uploaded by

genesisjohnhleysa
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 4

What is a thyristor?

A thyristor is a four-layer semiconductor device, consisting of alternating P-type


and N-type materials (PNPN). A thyristor usually has three electrodes: an anode,
a cathode and a gate, also known as a control electrode.

The most common type of thyristor is the silicon-controlled rectifier (SCR). When
the cathode is negatively charged relative to the anode, no current flows until a
pulse is applied to the gate. Then, the SCR conducts current until
the voltage between the cathode and anode is reversed or reduced below a
certain threshold or holding value. Using this type of thyristor, large amounts of
power can be switched or controlled using a small triggering current or voltage.

Devices using alternating current can be turned on and off by sending a signal to
the control gate. This device is called a gate turn-off, or GTO, thyristor. Previously,
thyristors needed the current to be reversed to turn off, making them difficult to
use with direct current systems.

Thyristors are useful in switching applications because they can be fully on or off.
This two-state capability differs from transistors, which operate in between on
and off states, waiting for a signal to conduct current.
3 states of thyristors
Thyristors operate in one of the following three states, depending on the
requirements:

1. Forward conducting This is a thyristor's primary operating mode. It is switched


to conducting mode and stays that way until the current falls below a specific
level, called the holding current.
2. Forward blocking The thyristor blocks the flow of current, despite voltage
being applied in the direction that would signal a diode to conduct it.
3. Reverse blocking mode. Current attempts to pass through the thyristor in the
opposite direction. However, a diode blocks it, and the thyristor is not
activated.

Applications for thyristors


Thyristors support high voltages and possess a simplified approach to switching
on and off states. As a result, they are used for the following applications:
 speed controls;
 light dimmers;
 camera flashes; and
 various types of circuits, such as inverter, logic and timer circuits.

A thyristor also can function as a circuit breaker in device power circuits.


They prevent power supply disruptions by connecting a Zener diode at the
thyristor gate. When power supply voltage levels exceed the Zener voltage, the
thyristor turns off the power supply output to the ground and activates circuit
breakers or fuses upstream from the power supply. This is called a crowbar
effect and protects devices being served by the power supply from damage.

Thyristors vs. transistors


Transistors need an electrical pulse to signal the device to conduct current. Their
primary mode is a waiting state in between on and off. Transistors also need their
base signal to be continuously refreshed to conduct current.

By contrast, thyristors can be fully off or fully on. Once a signal enters the
thyristor gate and activates the device, it remains open until a current reverse
occurs or the voltage drops below a specific level.

You might also like