REPUBLIC OF THE PHILIPPINES

DEPARTMENT OF PUBLIC WORKS AND HIGHWAYS

REGIONAL OFFICE VI
ILOILO 2ND DISTRICT ENGINEERING OFFICE
BALABAG, DUMANGAS, ILOILO

CY 2024 DPWH INFRASTRUCTURE PROGRAM

DETAILED ENGINEERING DESIGN PLAN FOR
CONSTRUCTION (COMPLETION) OF MULTI- PURPOSE
BUILDING OF BARANGAY IMPALIDAN, CALINOG, ILOILO
CALINOG, ILOILO

SUBMITTED: RECOMMENDED: APPROVED: CONCURRED:

JERMAIN CEM L. DEQUILLA EDUARD B. OREN ALLAN REY R. PAJIMNA

OIC-CHIEF, PLANNING AND DESIGN SECTION OIC-ASSISTANT DISTRICT ENGINEER DISTRICT ENGINEER BARANGAY CAPTAIN
DATE: DATE:
DATE: DATE:
 SUMMARY OF QUANTITIES

NOTE:

QUANTITY ARE APPROXIMATE ONLY,IT IS SUBJECT TO

CHANGE UPON CERTIFICATION AND RECOMMENDATION
OF PROJECT ENGINEER.

PROJECT NAME AND LOCATION: SHEET CONTENTS: DRAFTED: REVIEWED: SUBMITTED: RECOMMENDED: APPROVED: CONCURRED: SET NO. SHEET NO.
REPUBLIC OF THE PHILIPPINES
DEPARTMENT OF PUBLIC WORKS AND HIGHWAYS CY 2024 DPWH INFRASTRUCTURE PROGRAM MA. LANI J. GALLEGO
REGIONAL OFFICE VI DETAILED ENGINEERING DESIGN PLAN FOR SUMMARY
ENGINEERING ASST. SQ 2
ILOILO 2ND DISTRICT ENGINEERING OFFICE CONSTRUCTION (COMPLETION) OF MULTI- PURPOSE BUILDING OF OF
JERMAIN CEM L. DEQUILLA EDUARD B. OREN ALLAN REY R. PAJIMNA
BALABAG, DUMANGAS, ILOILO BARANGAY IMPALIDAN, CALINOG, ILOILO QUANTITIES
PREPARED: SHARYN C. SUPEÑA 1 1 15
CALINOG, ILOILO GIZA P. PLAZA ENGINEER II OIC-CHIEF, PLANNING AND DESIGN SECTION OIC-ASSISTANT DISTRICT ENGINEER DISTRICT ENGINEER BARANGAY CAPTAIN
ENGINEER II DATE DATE DATE DATE DATE
L. MEDIANA
 TABLE OF CONTENTS REPUBLIC OF THE PHILIPPINES

SQ-1 SUMMARY OF QUANTITY

D P W H
OFFICE OF THE BUILDING OFFICIAL
ARCHITECTURAL

A-1 PERSPECT IVE, VICINITY MAP

TABLE OF CONTENTS
SITE DEVELOPMENT PLAN

A-2 FLOOR PLAN, FRONT ELEVATION,

RIGHT ELEVATION, SCHEDULE OF
LAND USE AND ZONING
SPAN PER COLUMN

A-3 RIGHT SIDE ELEVATION, LEFT SIDE

ELEVATION THRU SECTION A-A & B-B,
EAVES DETAIL, GUTTER BEND DETAIL

STRUCTURAL

S-1 - GENERAL NOTES

S-2 - GENERAL NOTES

S-3 FOUNDATION PLAN, TIE

LINE AND GRADE
BEAM DETAIL, SCHEDULE
OF SPAN PER COLUMN,
SCHEDULE OF FOOTING,
SCHEDULE OF COLUMN,
PLAN AND SECTION

S-4 SCHEDULE OF STEEL BEAM, DETAIL

OF SB -1, DETAIL OF SB-2, DETAIL
OF SB -3, SPOT DETAILS, STEEL
BRACKET, SECTION OF STEEL BEAM

S-5 CENTER GIRT, ROOF FRAMING ARCHITECTURAL

PLAN, SCHEDULE OF SPAN PER
COLUMN FASCIA FRAME 1 DETAIL,
FASCIA FRAME 2
DETAIL,CONNECTION DETAIL OF
1 PERSPECTIVE CROSS BRACING ON TRUSSES,
CONNECTION DETAIL OF CROSS
A-1 NTS
BRACING ON COLUMN

S-6 TYPICAL ANCHORAGE DETAIL

STEEL BEAM/ TRUSSES
ANCHORAGE DETAIL, SCHEDULE STRUCTURAL
OF TRUSSES AND MEMBERS, MAIN
TRUSS DETAIL
THI
S SI S-7 SAG ROD ISOMETRIC, CONNECTION
TE DETAIL OF SAG ROD, CLEATS,
J-BOLTS & PURLINS, BRACING
DETAIL (OUTSIDE), BRACING
DETAIL (INSIDE), BRACING
ISOMETRIC, BRACING DETAIL
SECTION

SANITARY
PLUMBING

P-1 CATCH BASIN LAYOUT, DETAIL OF

CATCH BASIN, DETAIL OF SECTION,
CATCH BASIN ISOMETRIC

ELECTRICAL
E-1 VOLTAGE DROP CALCULATION,
SCHEDULE OF LOADS W/ BACK UP
COMPUTATION, ELECTRICAL PLAN, ONE
LINE DIAGRAM, GENERAL NOTES, LEGEND
ELECTRICAL
THIS SITE BILLBOARD
PB PROJECT BILLBOARD

LINOG
TO POB. CA

MECHANICAL

2 SITE DEVELOPMENT PLAN 3 VICINITY MAP

A-1 DRAWN NOT TO SCALE
A-1 DRAWN NOT TO SCALE

PROJECT NAME AND LOCATION: SHEET CONTENTS: DRAFTED: REVIEWED: SUBMITTED: RECOMMENDED: APPROVED: CONCURRED: SET NO. SHEET NO.
REPUBLIC OF THE PHILIPPINES
DEPARTMENT OF PUBLIC WORKS AND HIGHWAYS CY 2024 DPWH INFRASTRUCTURE PROGRAM MA. LANI J. GALLEGO
REGIONAL OFFICE VI DETAILED ENGINEERING DESIGN PLAN FOR PERSPECTIVE, ENGINEERING ASST. A-1 3
ILOILO 2ND DISTRICT ENGINEERING OFFICE CONSTRUCTION (COMPLETION) OF MULTI- PURPOSE BUILDING OF SITE DEVELOPMENT
PREPARED: ALAN M. LACUESTA JERMAIN CEM L. DEQUILLA EDUARD B. OREN ALLAN REY R. PAJIMNA
BALABAG, DUMANGAS, ILOILO BARANGAY IMPALIDAN, CALINOG, ILOILO PLAN,
VICINITY MAP
1 5 15
CALINOG, ILOILO GIZA P. PLAZA ARCHITECT II OIC-CHIEF, PLANNING AND DESIGN SECTION OIC-ASSISTANT DISTRICT ENGINEER DISTRICT ENGINEER BARANGAY CAPTAIN
ENGINEER II DATE DATE DATE DATE DATE
L. MEDIANA
 SCHEDULE OF SPAN PER COLUMN
NAME LENGTH SPAN ( LS)
SPAN-1 4500 MM
SPAN-2 4500 MM
SPAN-3 5000 MM
B SPAN-3&4 10000 MM A B C D E F G
SPAN-4 5000 MM
A B C D E F G SPAN-5 4500 MM 0.50MM THK. PRE PAINTED HI- RIB
CURVE TYPE LONG SPAN ROOFING
0.701mm THK. PRE- PAINTED
LENGTH SPAN-6 4500 MM GUTTER (GAUGE 24)
( BOX TYPE)
FLOOR LENGTH = 28000 MM APEX LINE OF TRUSS
1000 SPAN-1 SPAN-2 SPAN-3 & 4 SPAN-5 SPAN-6 1000
FLOOR WIDTH = 14000 MM

3500
TOP OF ROOF BEAM

8600
EXISTING STAGE

5000
1500

1500
2 2
TOP OF COURT SLAB

100
NATURAL GROUND LINE

FRONT
3
A-2
ELEVATION
FRONT ELEVATION
SCALE 1:150 M

EXISTING SLAB COURT

WIDTH

WIDTH
A A

G F E D C B A

0.50MM THK. PRE PAINTED HI- RIB

0.701mm THK. PRE- PAINTED CURVE TYPE LONG SPAN ROOFING
GUTTER (GAUGE 24)

1 1 ( BOX TYPE)
1500

1500
APEX LINE OF TRUSS

3500
1000 SPAN-1 SPAN-2 SPAN-3 SPAN-4 SPAN-5 SPAN-6 1000
TOP OF ROOF BEAM
LENGTH

8600
A B C D E F G

5000
B
TOP OF COURT SLAB

100
NATURAL GROUND LINE

1
FLOOR PLAN
FLOOR PLAN REAR
2 ELEVATION
REAR ELEVATION
A-2 SCALE 1:150 M A-2 SCALE 1:150 M

PROJECT NAME AND LOCATION: SHEET CONTENTS: DRAFTED: REVIEWED: SUBMITTED: RECOMMENDED: APPROVED: CONCURRED: SET NO. SHEET NO.
REPUBLIC OF THE PHILIPPINES
DEPARTMENT OF PUBLIC WORKS AND HIGHWAYS CY 2024 DPWH INFRASTRUCTURE PROGRAM MA. LANI J. GALLEGO
REGIONAL OFFICE VI DETAILED ENGINEERING DESIGN PLAN FOR FLOOR PLAN, FRONT
ELEVATION,
ENGINEERING ASST. A-2 4
ILOILO 2ND DISTRICT ENGINEERING OFFICE CONSTRUCTION (COMPLETION) OF MULTI- PURPOSE BUILDING OF RIGHT ELEVATION,
PREPARED: ALAN M. LACUESTA JERMAIN CEM L. DEQUILLA EDUARD B. OREN ALLAN REY R. PAJIMNA
BALABAG, DUMANGAS, ILOILO BARANGAY IMPALIDAN, CALINOG, ILOILO SCHEDULE OF
SPAN PER COLUMN
2 3 15
CALINOG, ILOILO GIZA P. PLAZA ARCHITECT II OIC-CHIEF, PLANNING AND DESIGN SECTION OIC-ASSISTANT DISTRICT ENGINEER DISTRICT ENGINEER BARANGAY CAPTAIN
ENGINEER II DATE DATE DATE DATE DATE
L. MEDIANA
 1 2 2 1

0.551MM THK. PRE- PAINTED 0.701mm THK. PRE- PAINTED 0.551MM THK. PRE- PAINTED 0.701mm THK. PRE- PAINTED 50
SIDE FLASHING (GAUGE 26) GUTTER (GAUGE 24) SIDE FLASHING (GAUGE 26) GUTTER (GAUGE 24) 10
( BOX TYPE) ( BOX TYPE)
0

50
APEX LINE OF TRUSS APEX LINE OF TRUSS
50

350

350
3500

3500
250
TOP OF ROOF BEAM TOP OF ROOF BEAM
8600

8600
GUTTER BEND LAYOUT
SB-1 SB-1 GUTTER
7
A-3
BEND LAYOUT
SCALE 1:20 M
5000

5000
TOP OF COURT SLAB TOP OF COURT SLAB
100

100
NATURAL GROUND LINE NATURAL GROUND LINE

4 RIGHT ELEVATION 5 LEFT ELEVATION

CU
RV
A-3 SCALE 1:150 M A-3 SCALE 1:150 M

E
RO
OF
IN
G
G.I. STRAP AT 1200 MM O.C.
STAINLESS STRAINER

2 1
PRE- PAINTED GUTTER
( BOX TYPE)

1000 LENGTH 1000

75 MM Ø PVC DOWN
SEE BRACING DETAIL
SPOUT
RD RD RD RD RD RD SEE TRUSS DETAIL
1500
1500

1500
SB-1
6 EAVES DETAIL
A-3 SCALE 1:20 M

SLOPE

2 THRU SECTION B-B

0.50MM THK. PRE PAINTED HI- RIB A-3 SCALE 1:150 M
A B C D E F G
WIDTH

WITDH

CURVE TYPE LONG SPAN ROOFING

APEX LINE OF TRUSS

SLOPE

3500
SEE TRUSS DETAIL

TOP OF ROOF BEAM

8600
1500

1500

5000
RD RD RD RD RD RD RD
1000 LENGTH 1000
TOP OF COURT SLAB

100
NATURAL GROUND LINE

1 ROOF PLAN THRU SECTION A-A

3
A-3 SCALE 1:150 M
A-3 SCALE 1:150 M

PROJECT NAME AND LOCATION: SHEET CONTENTS: DRAFTED: REVIEWED: SUBMITTED: RECOMMENDED: APPROVED: CONCURRED: SET NO. SHEET NO.
REPUBLIC OF THE PHILIPPINES
DEPARTMENT OF PUBLIC WORKS AND HIGHWAYS CY 2024 DPWH INFRASTRUCTURE PROGRAM MA. LANI J. GALLEGO
REGIONAL OFFICE VI DETAILED ENGINEERING DESIGN PLAN FOR FLOOR PLAN, FRONT
ELEVATION,
ENGINEERING ASST. A-3 5
ILOILO 2ND DISTRICT ENGINEERING OFFICE CONSTRUCTION (COMPLETION) OF MULTI- PURPOSE BUILDING OF RIGHT ELEVATION,
PREPARED: ALAN M. LACUESTA JERMAIN CEM L. DEQUILLA EDUARD B. OREN ALLAN REY R. PAJIMNA
BALABAG, DUMANGAS, ILOILO BARANGAY IMPALIDAN, CALINOG, ILOILO SCHEDULE OF
SPAN PER COLUMN
3 3 15
CALINOG, ILOILO GIZA P. PLAZA ARCHITECT II OIC-CHIEF, PLANNING AND DESIGN SECTION OIC-ASSISTANT DISTRICT ENGINEER DISTRICT ENGINEER BARANGAY CAPTAIN
ENGINEER II DATE DATE DATE DATE DATE
L. MEDIANA
 GENERAL CONSTRUCTION NOTES
GENERAL NOTES NOTES ON REINFORCEMENT NOTES ON COLUMNS
1. IN THE INTERPRETATION OF THE DRAWING, INDICATED DIMENSIONS SHALL GOVERN AND DISTANCES AND SIZES SHALL NOT BE 1. UNLESS OTHERWISE NOTED IN PLANS, THE YIELD STRENGTH OF REINFORCING BRS SHALL BE: 1. PROVIDE EXTRA SETS OF TIES AT 100mm O.C. FOR TIES COLUMN REINFORCEMENT ABOVE AND BELOW
SCALED FOR CONSTRUCTION PURPOSES. A. FOOTINGS, FOOTING BEAMS AND GIRDERSS--------------fy = 414 MPa (60,000 psi ) BEAM-COLUMN CONNECTIONS FOR A DISTANCE FROM FACE OF CONNECTION EQUAL TO THE GREATER OF
THE OVERALL THICKNESS OF COLUMN, 1/6 THE CLEAR HEIGHT OF COLUMN OR 450mm.
B. COLUMNS AND SHEAR WALLS ------------------------------------fy = 414 MPa (60,000 psi)
2. IN REFERENCE TO OTHER DRAWINGS, SEE ARCHITECTURAL DRAWINGS FOR DEPRESIONS IN FLOOR SLABS, OPENINGS IN THE
WALLS AND SLABS, INTERIOR PARTITIONS, LOCATION OF DRAINS ETC. C. BEAMS AND GIRDER---------------------------------------------------fy = 414 MPa (60,000 psi)
NOTES ON BEAMS AND GIRDERS
2. COLUMN TIES SHALL BE PROTECTED EVERYWHERE BY A COVERING OF CONCRETE CAST MONOLITHICALLY 1. UN LESS, OTHERWISE NOTED IN THE PLANS. CAMBER ALL BEAMS AND GIRDER AT LEAST 6mm FOR EVERY
D. NO-LOAD BEARING WALL PARTITIONS, BEDDED SLABS, FLOOR & ROOF SLABS, PARAPETS, CATCH BASIN, 4.50m OF SPAN. EXCEPT CANTILEVERS FOR WHICH THE CAMBER SHALL BE AS NOTED IN THE PLANS OR AS
SIDEWALK,---------------------------------------------------------------------fy = 275 MPa (40,000 psi) WITH THE CORE WITH THE MINIMUM THICKNESS OF 40mm AND NOT LESS THAN 40 TIMES THE MAXIMUM SIZE
3. IN CASE OF DISCREPANCIES AS TO THE LAYOUT, DIMENSIONS, AND ELEVATIONS BETWEEN THE STRUCTURAL PLANS, AND ORDERED BY THE ENGINEER BUT IN NO CASE LESS THAN 20mm FOR EVERY 3.0m OF FREE SPAN.
OF COARSE AGGREAGATEE IN MILIMETERS.
ARCHITECTURAL DRAWINGS, THE CONTRACTOR SHALL NOTIFY BOTH STRUCTURAL ENGINEER AND ACRCHITECT.
2. ALL REINFORCING BARS SIZE 10mm OR LARGER SHALL BE DEFORMED IN ACCORDANCE WITH A STM A 706. BARS SMALLER THAN 3. WHERE COLUMNS CHANGE IN SIZE. VERTICAL REINFORCEMENTS SHALL BE OFFSET AT A SLOPE OF NOT
10mm MAY BE PLAIN. 2. TYPICAL BARS BENDING AND CUTTING DETAILS FOR BEAMS SHALL BE AS SHOWN IN FIG. B-1
MORE THAN 1 IN 6 AND EXTRA 10mm TIES AT 100mM SHALL BE PROVIDED THRU OUT THE OFFSET REGION.
4. ALL CONCRETE WORK SHALL BE DONE IN ACCORDANCE WITH ACI318-95 BUILDING CODE REQUIREMENTS FOR REINFORCED 3. SPLICES SHALL BE SECURELY WIRED TOGETHER & SHALL LAP OR EXTEND IN ACCORDANCE W/ TABLE A & TABLE B ( TABLE OF LAP
CONCRETE AND ALL STRUCTURAL STEEL WORK ACCORDING TO AISC SPECIFICATION (9TH EDITION) IN SO FAR AS THEY DO NOT SPLICE & ANCHORAGE LENGTH) UNLESS OTHERWISE SHOWN ON DRAWING, SPLICES SHALL BE STAGGERED WHENEVER POSSIBLE.
CONFLICT WITH LOCAL BUILDING CODE REQUIREMENT. 4. UNLES OTHERWISE INDICATED IN THE PLANS, LAP SPLICES FOR VERTICAL COLUMN REINFORCEMENT SHALL
BE MADE WITHIN THE CENTER HALF OF COLUMN HEIGHT, AND THE SPLICE LENGTH SHALL NOT BE LESS THAN
40 BAR DIAMETERS. WELDING OR APPROVED MECHANICAL DEVICES MAY BE USED PROVIDED THAT NOT LAP SPLICES ARE ALLOWED
MORE THAN ALTERNATE BARS ARE WELDED OR MECHANICALLY SPLICED AT ANY LEVEL AND THE VERTICAL ONLY IN THIS PORTION
5. ACI REFRES TO AMERICAN CONCRETE INSTITUTE, AISC TO AMERICAN INSTITUTE OF STEEL CONSTRUCTION AND ASTM TO AMERICAN UNLESS OTHERWISE SHOWN, REINFORCEMENT IN CONTINOUS ELEVATED SLAB SHALL BE CUT AS FOLLOWS:
DISTANCES BETWEEN THESE WELDS OR SPLICES OF ADJACENT BARS IS NOT LESS THAN 600mm.
SOCIETY OF TESTING MATERIALS. L1 L2 L3
L2/3 L2/3 L3/3 L3/3
6. CONSTRUCTION NOTES AND TYPICAL DEAILS APPLY TO ALL DRAWINGS UNLESS OTHERWISE SHOWN OR NOTED. MODIFY TYPICAL
2D 2D 2D 2D 2D
DETAILS AS DIRECTED T O MEET SPECIAL CONDITIONS.
NOTES ON CONCRETE SLABS
7. SHOP DRAWINGS WITH ERECTION AND PLACING DIAGRAMS OF ALL STRUCTURAL STEELS, MISCELLANEOUS IRON, PRE-CAST
1. ALL SLAB REINFORCEMENTS SHALL BE 20mm CLEAR MINIMUM FROM BOTTOM AND FROM THE TOP OF SLAB.

D
CONCRETE, ETC. SHALL BE SUBMITTED FOR ENGNEERS APPROVAL BEFORE FABRICATION. H JOINT HOOP SPACE @ "2Sh" WHEN THERE ARE
BEAMS HAVING WIDTH OF AT LEAST ONE-HALF THE
COLUMN WIDTH & DEPTHS NOT LESS THAN THREE
2. UNLESS OTHERWISE SHOWN, REINFORCEMENT IN CONTINOUS ELEVATED SLAB SHALL BE CUT AS FOLLOWS: CROSS-TIE L2/5 L2/5 L3/5 L3/5
8. CONTRACTOR SHALL NOTE AND PROVIDE ALL MEISCELANEOUS CURBS, SILLS, STOOLS, EQUIPMENT'S AND MECHANICAL BASES THAT QUARTERS OF THE DEEPEST BEAM THAT FRAME
ARE REQUIRED BY THE ARCHITECTURAL, ELECTRICAL, AND MECHANICAL DRAWINGS. INTO FOUR SIDES OF THE COLUMN. ALL OTHER

350mm MAX
CONDITIONS USE HOOPS @"Sh" CENTERS. BOTTOM BARS WEB BARS
2 - Ø12mm SIDE BARS
TOP BARS

10
9. ALL RESULTS OF MATERIAL TESTING FOR CONCRETE, REINFORCING BARS & STRUCTURAL STEEL MUST BE NOTED & APPROVED BY L1 L2

H
m
THE STRUCTURAL ENGINEER.

in
L1/3 TOP BAR L1/3 L2/3 TOP BAR

.
FIG. B-1
NOTES ON CONCRETE MIXES & PLACING

CONF. REINF.
L1/6 BOTTOM BAR L1/6 L2/5 L2/5 BOTTOM BAR
1. ALL CONCRETE SHALL DEVELOP MIN. COMPRESSIVE STENGTH AT THE END OF TWENTY EIGHT (28) DAYS W/ CORRESPONDING
MAXIMUM SIZE AGGREGATE & SLUMPS AS FOLLOWS. JOINT HOOP SPACE @ "2Sh" WHEN THERE ARE TABLE 'A' TABLE 'B'

D
BEAMS HAVING WIDTH OF AT LEAST ONE-HALF THE TENSION BARS COMPRESSION BARS

LOCATION 28 DAYS STRENGTH MAX. SIZE OF MAX. SLUMP

COLUMN WIDTH & DEPTHS NOT LESS THAN THREE EMBEDMENT LENGTHS AND EMBEDMENT LENGTHS AND

JOINT REINF.
QUARTERS OF THE DEEPEST BEAM THAT FRAME LAPPED SPLICED IN MILLIMETERS LAPPED SPLICED IN MILLIMETERS
AGGREGATE
INTO FOUR SIDES OF THE COLUMN. ALL OTHER
ALL OTHERS, INCLUDING 4000 PSI ( 27.6 MPa) 20mm 100mm CONDITIONS USE HOOPS @"Sh" CENTERS. BAR SIZE fc'= 20.7MPa(3000psi) fc'= 27.6 .7MPa(4000psi) BAR SIZE fc'= 20.7MPa(3000psi) fc'= 27.6 .7MPa(4000psi)
SLABS, DEFORMED DEFORMED
TYPICAL BAR BENDING AND CUTTING DETAILS FOR SLLABS EMBEDMENT LAPPED EMBEDMENT LAPPED EMBEDMENT LAPPED EMBEDMENT LAPPED

CONF. REINF.PER SCHEDULE CONF. REINF.

COLUMNS 4000 PSI ( 27.6 MPa) 20mm 100mm
IF SLABS ARE REINFORCED BOTHWAYS BARS ALONG THE SHORTER SPAN SHALL BE PLACED BELOW THOSE ALONG THE 10mmØ 300 300 300 300 10mmØ 225 300 200 300
3.
BEAMS, SLABS 4000 PSI ( 27.6 MPa) 20mm 100mm

D
LONG SPAN AT THE CENTER AND OVER THE LONGER SPAN FOR REINFORCING BARS NEAR THE SUPPORTS. THE SPACING

Sh
12mmØ 300 300 300 300 12mmØ 275 300 250 300
3000 PSI ( 27.6 MPa) 20mm 100mm OF THE BARS AT THE COLUMN STRIPS SHALL NOT BE MORE THAN ONE AND A HALF ( 1 1/2) SLAB THICKNESS.
SLAB ON FILL 16mmØ 300 400 300 400 16mmØ 350 400 325 400
FOOTING 3000 PSI ( 27.6 MPa) 20mm 100mm

COLUMN TIES AS
20mmØ 400 550 350 500 20mmØ 450 500 475 500
4. TEMPERATURE BARS FOR SLAB SHALL BE GENERALLY PLACED NEAR THE FACE IN TENSION AND SHALL NOT BE LESS FOR COL. BAR SPLICES SEE TABLE OF MIN. LAP 625 625
2. MAINTAIN MINIMUM CONCRETE COVER FOR REINFORCING STEEL AS FOLLOWS: 25mmØ 600 800 550 750 25mmØ 550 550
THAN 0.0025 X GROSS-SECTIONAL AREA (Ag) OF THE SLAB (SEE SCHEDULE BELOW) SPLICE LENGTH OF COLUMN REINFORCEMENT
SUSPENDED SLABS -----------------------------------------------------------------------------------------------------------20mm ( SPACING OF TIES ALONG THIS REGION SHALL NOT 28mmØ 750 1000 650 850 28mmØ 625 675 625 675
SLAB ON GRADE-----------------------------------------------------------------------------------------------------------------40mm BE LESS THAN 100mm)
32mmØ 950 1300 850 1100 32mmØ 700 775 700 775
WALL ABOVE GRADE----------------------------------------------------------------------------------------------------------25mm
NOTE: TOP PLAIN BARS, MULTIPLY VALUE BY 2 NOTE: TOP PLAIN BARS, MULTIPLY VALUE BY 2
BEAMS STIRRUPS AND COLUMN TIES---------------------------- ----------------------------------------------------40mm SCHEDULE OF MINIMUM SLAB REINFORCEMENT
WHERE CONCRETE IS EXPOSED TO VALUES GIVEN ABOVE CAN ALSO BE USED FOR

Sh
THICKNESS MINIMUM TEMPERATURE BARS

D
COLUMNS.
EARTH BUT POURED AGAINST FOORMS------------------------------------------------------------------------------50mm
WHERE CONCRETE IS DEPOSITED 100mm 10mm Ø @ 250mm EACH WAY NOTE: IF THE BEAM REINFORCING BRS END IN A WALL THE CLEAR DISTNCE FROM THE BAR TO THE FARTHEST FACE OF THE WALL SHALL

D JOINT REINF.
DIRETLY AGAINST EARTH---------------------------------------------------------------------------------------------------75mm 3.
125mm 10mm Ø @ 225mm EACH WAY NOT BE LESS THAN 25mm. EMBEDMENT LENGTH SHALL BE AS SHOWN IN A TABLE Ä"FOR TENSION BARS AND TABLE 'B'FOR
3. CONCRETE SHALL BE DEPOSITED IN ITS FINAL POSITION IN ITS FINAL POSITION WITHPUT SEGREGATION. RE-HANDLING OR PLACING ALL CONCRETE REINF. DETAIL SHOULD BE DONEIN
ACCORDANCE WITH THE LATEST EDITION OF ACI COMPRESSION BARS. UNLESS SPECIFIED IN PLAN, TOP BAR SHALL NOT BE SPLICED WITH IN THE COLUMN OR WITHIN A DISTANCE
SHALL BE DONE PREFERABLY WITH BUGGIES, BUCKETS OR WHEELBARROWS, NO CHUTES WILL BE ALLOWED EXCEPT TO 150mm 10mm Ø @ 185mm EACH WAY TWICE THE MEMBER DEPTH FROM THE FACE OF COLUMN. AT LEAST TWO STIRRUPS SHALL BE PROVIDED AT ALL SPLICES.
TRANSFER CONCRETE FROM HOPPERS TO BUGGIES, WHEELBARROWS OR BUCKETS IN WHICH CASE THEY SHALL NOT EXCEED SIX DETAILING MANUAL

CONF. REINF.
(6) METERS IN AGGREGATE LENGTH. 175mm 10mm Ø @ 150mm EACH WAY

200mm 10mm Ø @ 140mm EACH WAY

4. IF THERE ARE TWO OR MORE LAYERS OF REINFORCING BARS, USE 25mmØ BAR SEPARATORS SPADED AT 1.0m ON CENTER. IN NO
4. NO DEPOSITINGOF CONCRETE SHALL BE ALLOWED WITHOUT THE USE OF VIBRATORS UNLESS AUTHORIZED IN WRITING BY THE CASE SHALL THERE BE LESS THAN TWO (2) SEPARATORS BETWEEN TWO LAYERS OF BARS.
DESIGNERS AND ONLY FOR UNUSUAL CONDITIONS WHERE VIBRATIONS IS EXTREMELY DIFFICUT TO ACCOMPLISH. UNLESS OTHERWISE NOTED IN THE PLANS ALL BEDDED SLABS SHALL BE REINFORCED WITH 10mm Ø AT 250mm O.C. EACH
5.
WAY TO CENTER OF SLAB AND CONSTRUCTION JOINTS FOR SAME SHALL NOT BE LESS THAN 3.65 METER APPART. TYPICAL COLUMN ELEV. SHOWING 5.
MINIMUM CONCRETE PROTECTION FOR REINFORCING BARS OR STEEL SHAPES SHALL BE AS SHOWN IN FIG. B-2 UNLESS SPECIFIED
ELSEWHERE.
5. ALL ANCHOR BOLTS, DOWELS , AND OTHER INSERTS, SHALL BE PROPERLY POSITIONED & SECURED IN PLACE PRIOR TO PLACING OF
CONCRETE.
DOWELS AND TIES SPACING
6. PROVIDE EXTRA REINFOREMENTS FOR CORNEER SLAB ( TOW ADJACENT DISCONTINUOUS EDGES) AS SHOWN BELOW.
6. ALL CONCRETE SHALLBE KEPT MOIST FOR A MINIMUM PF SEVEN CONSCUTIVE DAYS IMMEDIATELY AFTER POURING BY THE UE OOF
BURLAO, FOG SPRAYING, CURING COMPUNDS OR OTHER APPROVED METHODS. b
7. CONCRETE SLAB REINFOREMENTS SHALL BE PROPERLY SUPPORTED WITH 10mmØ STEEL CHAIR OR APPROVED
EQUIVALENT SPACED AT 1.0 METER ON CENTER BOTHWAYS
LAP SPLICE LENGTH: MAIN REINFORCEMENT

t
7. FOUNDATION --------------------------------------------------------------------------------------------------------------------24 HRS. A AT ANY LEVEL NO MORE THAN ALTERNATE BARS
SUSPENDED SLAB EXCEPT WHEN SHOULD BE SPLICED MIN. DISTANCE BET. TWO
ADDITIONAL LOADS ARE IMPOSED------------------------------------------------------------------------------------- 8 DAYS ADJACENT BARS SPLICES SHALL BE 600mm. WEB BARS
Ø12X1000 LONG AT

ht.
SEE NOTE

t OR 41 D
WALLS-------------------------------------------------------------------------------------------------------------------------------21 DAYS MID-DEPTH OF SLAB AT SLEEVES FOR UTILITY

t
WITHIN CENTER
DOWN INTO EDGE BEAM. EXTENDED 4 - Ø12@ 1800 LOG SEE NOTE
BEAMS ---------------------------------------------------------------------------------------------------------------------------- 14 DAYS EACH CORNER PIPES MAX. 51 D

D
TOP BARS BEND BARS MIN. OF 1200 (4'-0") INTO BARS

HALF OF "H
COLUMNS--------------------------------------------------------------------------------------------------------------------------21 DAYS 1 - Ø12 TOP & BOT BARS
L/4
0.025M Ø
8. THE CONTRACTOR SHALL SUBMIT THE SCHEDULE OF POURING AND THE LOCATION OF THE CONSTRUCTION JOINTS TO THE 4 - Ø12 BOTT. BARS TOP BARS @ SUPPORT (CONT) SEPARATOR PROVIDE 3-Ø10 EXTRA STIRR. EACH
STRUCTURAL ENGINEER AT LEAST (4) DAYS PRIOR TO THE POURING FOR APPROVAL. SEE NOTE SIDE OF SLEEVES
400

1 - Ø12 EA. REQ'D. BOTT. BARS @ SUPPORT

TOP & BOT
9. THE CONTRACTOR SHALL FURNISH AND MAINTAIN ADEQUATE FORMS AND SHORINGS UNTIL THE CONCRETE MEMBERS HAVE TYP. DET. FOR SLEEVES

JT. REINF.
ATTAINED THEIR WORKING CONDITION AND STRENGTH. NOTE:

JT. REINF.
SLAB THRU CONCRETE BEAM

D
0

38mm
60

20mm CLEAR FOR JOIST

OPENING CLEAR 40mm CLEAR FOR BEAMS
0

AND GIRDER
NOTES ON FOOTINGS
60

1 - Ø12 EA.
400

1. FOOTINGS ARE DESIGNED FOR AN ALLOWANCE SOIL BEARING PRESSURE F 96 KPa (2000 psf). CONTRACTOR SHALL REPORT TO THE
ENGINEER, IN WRITING, THE ACTUAL SOIL CONDITIONS UNCOVERED AND COMFIORM ACTUAL BEARING CAPACITY OF SOIL BEFORE TOP & BOT SPLICE BOTTOM BARS AT MID SPAN FIG. B-2 FIG. B-3
DEPOSITING CONCRETE.
IN TWO WAY SLAB EXTEND SECTION "A" EXTRA TOP BARS @ SUPPORT
BARS UP TO BEAM SUPPORT
OMIT TRIMMER BARS WHERE 6. WHEN A BEAM CROSSES A GIRDER, REST BEAM ON TOP OF GIRDER BARS, BEAM REINFORCING BAR SHALL
2. FOOTING SHALL REST AT LEAST 1500mm BELOW NATURAL GRADE LIN UNLESS OTHERWISE INDICATED IN PLANS. NO FOOTING SHALL 60
REST ON FILL.
0 OPENING IS FRAME BY BEAM TYPICAL DETAIL OF COL. LAP SPLICE & EXT. BE SYMMETRIAL BOUT CENTER LINE WHENEVER POSSIBLE.
GIRDER TO COL. CONNECT. 7. GENERALLY NO SPLICES SHALL BE PERMITTED AT A POINTS WHERE CRICTICAL BENDING STERSSES OCCUR,
3. MINIMUM CONCRETE PROTECTION FOR REINFORCEMENTS SHALL BE 75mm CLEAR FOR CONCRETE DEPOSITED THE GROUND AND TYPICAL SLAB SPLICES WHERE SO PERMITTED SHALL BE INDICATED IN THE TABLE 'A' AND 'B'. WLEDED SPLICES SHALL
50mm FOR CONCRETE DEPOSITED AGAINST THE FORMWORK.
TYPICAL CORNER SLAB DETAIL OPENING DETAIL DEVELOP IN TENSION AT LEAST 125% OF THE SPECIFIED YIELD STRENGTH OF THE BAR, NOT MORE THAN 50%
OF THE BARS AT ANY ONE SECTION IS ALLOWED TO BE SPLICED THEREIN.

PROJECT NAME AND LOCATION: SHEET CONTENTS: DRAFTED: REVIEWED: SUBMITTED: RECOMMENDED: APPROVED: CONCURRED: SET NO. SHEET NO.
REPUBLIC OF THE PHILIPPINES
DEPARTMENT OF PUBLIC WORKS AND HIGHWAYS CY 2024 DPWH INFRASTRUCTURE PROGRAM MA. LANI J. GALLEGO
REGIONAL OFFICE VI DETAILED ENGINEERING DESIGN PLAN FOR ENGINEERING ASST. S-1 6
ILOILO 2ND DISTRICT ENGINEERING OFFICE CONSTRUCTION (COMPLETION) OF MULTI- PURPOSE BUILDING OF GENERAL NOTES
JERMAIN CEM L. DEQUILLA EDUARD B. OREN ALLAN REY R. PAJIMNA
BALABAG, DUMANGAS, ILOILO BARANGAY IMPALIDAN, CALINOG, ILOILO PREPARED: SHARYN C. SUPEÑA 1 7 15
CALINOG, ILOILO GIZA P. PLAZA ENGINEER II OIC-CHIEF, PLANNING AND DESIGN SECTION OIC-ASSISTANT DISTRICT ENGINEER DISTRICT ENGINEER BARANGAY CAPTAIN
ENGINEER II DATE DATE DATE DATE DATE
L. MEDIANA
 GENERAL CONSTRUCTION NOTES
NOTES ON CONCRETE WALLS 2. DESIGN STRESSES
A. CONCRETE
1. ALL WALLS SHALL BE REINFORCED ACCORDING TO THE FOLLOWING SCHEDULE OF WALL COMPRESSIVE STRENGTH @ 28 DAYS fc' = 20.70 MPa ( 3,000 psi )
FLR .SLAB OR BEAM REINFORCEMENT UNLESS OTHERWISE INDICATED IN THE PLANS. B. REINFORCING BARS
NOTES ON CONCRETE HOLLOW BLOCKS WALLS DOWEL BARS TO
a. FOR BARS 16MMØ AND GREATER (INTERMEDIATE GRADE DEFORMED BAR) fy = 414 MPa (60,000 psi )
MATCH VERT. BARS
B. FOR BARS LESS THAN 16MMØ (STRUCTURAL GRADE DEFORMED BAR) fy = 275 MPa (40,000 psi )
1. UNLESS OTHERWISE SHOWN IN PLANS ALL CONCRETE HOLLOW BLOCKS AND CERAMIC BLOCKS REINFORCEMENT C. STRUCTURAL STEEL, ASTM - A36

DOWEL
WALL VERTICAL
SHALL BE REINFORCED AS SHOWN IN THE SCHEDULE OF CONCRETE HOLLOW BLOCKS AND THICKNESS SECTION

400
FOR TRUSSES, BRACINGS, & STRUTS fy = 248 MPa (36,000 psi )

VERIFY ARCHITECTURAL
HORIZONTAL VERTICAL REMARKS
CERAMIC BLOCK REINFOREMENT.
1. ALL JOINTS AND CELLS 100mm 10Ømm @ 250mm O.C. 10Ømm @ 300mm O.C. HORIZONTAL BARS
D. PURLINS
VERT.
CONTAINING REINFORCING 125mm 10Ømm @ 200mm O.C. 10Ømm @ 250mm O.C. BARS COLD FORMED LIGHT GAGE SHAPES fy = 248 MPa (36,000 psi )
AT CENTERS VERTICAL
2. PROVIDE 150mm X 300mm STIFFENER COLUMN REINFORCED WITH 12-12mm WITH 6mM TIES AT BARS SHALL BE FILLED W/ HOR. E. MASONRY UNIT (CHB)
150mm 12Ømm @ 250mm O.C. 12Ømm @ 300mm O.C. BARS STAGGERED OUT
150mm IN CENTE WHERE CONCRETE HOLLOWBLOCK REMINATES AND EVERY 3.0M LENGTH OF CONCRETE GROUT BARS
NON-LOAD BEARING CHB WALLS fm' = 3.45 MPa (500 psi )
CONCRETE HOLLOW BLOCKS WALLS UNLESS NOTED IN STRUCTURAL PLANS. F. WELDS-USED E-60xx ELECTRODE
1. FOR REINFORCEMENTS SEE REINFORCING BARS SHALL HAVE 25mm CLEAR CONCRETE COVER FROM FACE OF WALL EXCEPT FOR WALLS IN CONTACT
CONSTRUCTION NOTES WITH THE GROUND WHERE A MINIMUM OF 60mm SHALL BE PROVIDED, AND FOR EXPOSED FAES OF FORMED WALLS G. STRUCTURAL BOLTS, ASTM-A307
WHERE THE MINIMUM SHALL BE 50mm CLEAR. a. Ft = 96.60 MPa (14,000 psi ) b. Fv = 69 MPa ( 10,000 psi )

DOWEL
400
1 - Ø CONT. HOR. BARS 2. CARRY VERTICAL BARS AT LEAST 60MM ABOVE FLOOR LEVEL TO PROVIDE FOR SPLICES WHEN NECESSARY STOP AT
SCHEDULE OF CONC. HOLLOW BLOCK AND CERAMIC BLOCK REINFORCEMENT 50mm BELOW TOP SLAB OR SOLID BAND WHERE THE WALLS ENDS. VERTICAL AND HORIZONTAL BARS SHALL BE SPLICED NOTES ON CONSTRUCTION JOINTS IN CONCRETE
BLOCK FOR FLOOR SLAB ONLY
REINFORCEMENT NOTES BY LAPPING A DISTANCE EQUAL 30 DIAMETERS AND WIRED SECURELY WITH 16 G.I. WIRE PROVIDEDTHAT SPLICES IN WHERE A CONSTRUCTION JOINT IS TO BE MADE, THE SURFACE OF CONCRETE SHALL BE CLEANED
THICKNESS 1.
A. MINIMUM LAPS AT SPLICE = 0.25M
ADJASCENT BARS ARE STAGGERED AT LEAST 1.50M O.C. AND ALL LAITANCE AND STANDING WATER REMOVED, SHEAR KEY SHALL BE PROVIDED AT THE
HORIZONTAL VERTICAL
B. PROVIDE RIGHT ANGLED REINFORCEMENT JOINT.
75mm 10mmØ @ 600mm O.C. 10mmØ @ 600mm O.C. AT CORNERS 0.92M LONG 4. UNLESS OTHERWISE NOTED IN THE PLANS, ALL OPENINGS IN WALLS 250mm OR THICKER SHALL BE REINFORCED AROUND
125mm
TYPICAL SECTION OF MASONRY WITH
1. 2-20mmØ BARS FOR 225mm, 200mmn, 175mm, 150mn, USE 2-16mmØ, FOR 125mm AND 100MM WALLS, USE 2-12mmØ MAIN REINFORCEMENTS TO BE
10mmØ @ 600mm O.C. 10mmØ @ 600mm O.C. C. WHERE CHB OR CER. BLK. WALL DOWELS
JOIN COL. R.C. BEAMS AND WALL, DOWELS PARTITION REINFORCEMENTS BARS. ALL WALLS AND SPACED ACCORDING TO THE SCHEDULE UNLWESS OTHERWISE NOTED (SEE FIG. 1) CONTINOUS ( TOP & BOTT. BARS)
150mm 10mmØ @ 600mm O.C. 10mmØ @ 600mm O.C. WITH THE SAME SIZE AS VERT. OR HOR.
REINFORCEMENTS SHALL BE PROVIDED WHERE JOINTS IS AT POINT OF
200mm MAIN REINFORCEMENTS
12mmØ @ 600mm O.C. 12mmØ @ 600mm O.C. STRESS, PROVIDE SHEAR RODS TO BE CONTINUOUS
WITH ENGINEERS APPROVAL
Ø10 X 1000 LONG
4- Ø16 VERT. BARS 30 BAR DIA. 30 BAR DIA. @ 300 O.C.
REINFORCING CONCRETE LINTEL BEAM IN 50
(MIN) (MIN)
4- Ø16 VERT. BARS

550
40
CONCRETE BLOCK WALLS

D/3
550
SEE CONSTRUCTION NOTES

t /3
D/3

D
LINTEL IN BLOCKS WALLS

t /3
FOR MASONRY WALL REIN-

t
D/3
FORCEMENTS (TYPICAL)

t /3
CLEAR TOTAL MIN. HEIGHT OF REINFORCEMENT
SPAN LENGTH fc' LINTEL FIN FLR LVL
("L") (L+0.40M) (MPa) (MM) BEAM SLAB

600 (MIN) VARIES

BOTTOM TOP STIRRUPS
550 550
1.20 M 1.60 M 200 1-Ø10 1-Ø10 Ø6mm @ 200 NAT. GRD. LVL.
1.50 M 1.90 M 14 200 1-Ø10 1-Ø10 Ø6mm @ 200 DOWEL BARS TO MATCH
CHB VERTICAL BARS TYPICAL SLAB & BEAM
1.80 M 2.20 M 200 1-Ø12 1-Ø10 Ø6mm @ 200
Ø10 BOTT. BARS
TYPICAL CONNECTION DETAIL
CONSTRUCTION JOINT DET.
2.10 M 2.50 M 250 1-Ø10 1-Ø10 Ø6mm @ 200 @ 300 O.C. OF RC WALL AT CORNERS

250
2.40 M 2.90 M 17 250 1-Ø12 1-Ø10 Ø6mm @ 200
2.70 M 3.10 M 250 1-Ø16 1-Ø12 Ø10mm @ 200 3 - Ø10 BOTT BARS

3.00 M 3.40 M 300 1-Ø16 1-Ø12 Ø10mm @ 200

3.30 M 3.70 M 20 300 1-Ø16 1-Ø12 Ø10mm @ 200 400 NOTES ON WELDS
3.60 M 4.00 M 300 1-Ø20 1-Ø12 Ø10mm @ 200
1. USE E70xx ELECTRODES FOR ALL MEMBERS WELDED.

DOWEL TO MATCH 2. WELDS SHALL DEVELOP THE FULL STRENGTH OF MEMBERS JOINED UNLESS OTHERWISE SHOWN
OR DETAILED IN THE DRAWINGS.
CHB VERT BARS DOOR
OPENING
12 THK. EXPANSION JOINT NOTE:
WITH MASTIC FILLER 300 PROVIDE THESE ADDITIONAL BARS FOR
1 - Ø16 VERT. BARS NOTES ON WELDS ALL OPENINGS PLUS BRS (NOT SHOWN) 39mm

DOWEL
( TYP. )
PARALLEL TO SIDE OF OPENING EQUAL CLEAR WINDOW

400
CHB WALL 1. STRUCTURAL STEEL TO BE USED FOR FABRICATION AND ERECTION OF THIS STRUCTURE SHALL
COMPLY WITH ALL THE PERTINENT PROVISION OF AISC SPECIFICATION FOR DESIGN, FABRICATION TO THE NUMBER OF TERMINATED BARS OPENING
DOWEL

FOR SIZE AND SPACING FIN. FLR. LVL. AT OPENING

AND ERECTION OF STRUCTURAL STEEL FOR BUILDING LATEST EDITION.
400

1- Ø16 VERT. BARS OF HOR. & VERT. BARS

250
CHB WALL (SEE CONSTRUCTION 2. ALL STRUCTURAL STEEL SHAPES SHALL BE CONCFORM TO ASTM A36 STRUCTURAL STEEL UNLESS SEE ARCHITECTURAL & MECHANICAL
NOTES) OTHERWISE INDICATED.
FOR SIZE AND SPACING PLANS FOR SLAB OPENING LOCATION
3 - Ø10 BARS ( AS SHOWN)
OF HOR. & VERT. BARS 3. ALL WELDED CONNECTIONS SHALL DEVELOP THE FULL STRENGTH OF THE MEMBERS CONNECTED.
Ø10 BOTT BARS @ 300 O.C.
SEE CONSTRUCTION NOTES. 400 4. UNLESS OTHERWISE SPECIFIED ALL WELDING RODS SHALL CONFORM AWS E60 ELECTRODED.
CORNER WALL OPENING OR END WALL 5. ALL BOLTS USED UNLESS OTHERWISE SPECIFIED SHALL BE ASTM A 307 BOLTS.

TYPICAL EXTERIOR WINDOW & DOOR OPENING

DOWEL TO MATCH
CHB VERT BARS
NOTES ON EMBEDED PIPES
1- 16 VERT. BARS R.C. COLUMN OR WALL

12 THK. EXPANSION JOINT DOWEL BARS TO MATCH WHERE DEPRESSED

A. ALL EMBEDED PIPES FOR UTILITIES, ETC, THAT PASS THRU BEAMS SHALL NOT EXCEED 100mm IN
DIAMETER OR 1/3 BEAM DEPTH WHICHEVER IS LESS, UNLESS OTHERWISE APPROVED IN WRITING
NOTES OF STIRRUPS
CHB HOR BARS 300 SLAB OCCURS 1. ALL REINFORCEMENT SHALL BE BENT COLD UNLESS OTHERWISE PERMITTED BY THE STRUCTURAL
WITH MASTIC FILLER BY THE STRUCTURAL ENGINEER.
ENGINEER

DOWEL
( TYP. )
CHB WALL 12 THK. EXPANSION JOINT B. NO PIPES SHALL BE ALLOWED TO PASS THRU BEAMS VERTICALLY.

400
2. REINFORCEMENT PARTIALLY EMBEDED IN CONCRETE SHALL NOT BE FILLED BENT, EXCEPT AS
WITH MASTIC FILLER C. NO PIPES SHALL BE EMBEDED IN COLUMNS SHOWN IN THE DESIGN DRAWINGS OR PERMITTED BY THE STRUCTURAL ENGINEER.
DOWEL

3. TIES & CLOSE STIRRUPS MUST BE BENT AT 135°

250
400

FOR SIZE AND SPACING

3 - Ø10 BARS ( AS SHOWN)
DESIGN CRITERIA db
OF HOR. & VERT. BARS
Ø10 BOTT BARS @ 300 O.C. 1. LOADINGS L
SEE CONSTRUCTION NOTES. 400

D+2db
D db
400 A. DEAD LOAD
135º HOOKS

L
DOWEL CONCRETE - 23.56 kN/m³
STEEL - 76.93 kN/m³
INTERSECTION WALL INTERSECTIG R.C. COLUMN OR WALL 150mm THK. CHB WALL - 2.73 kPa
4db or 65mm
TYPICAL CHB FOOTING DETAILS 100mm THK. CHB WALL - 2.11 kPa
6
TYPICAL CONNECTION DETAIL OF MASONRY WALL ( WHERE APPLICABLE ) db

D
B. LIVE LOAD 180º END HOOKS
ROOF - 1.00 kPa

db
C. WIND LOAD (NSCP 2010)
BASIC WIND VELOCITY, V = 250 KPH

12 db
200(MIN) 200(MIN) P = qh[(GCpf)-(GCpi)] (DESIGN WIND PRESSURE)

L
WHERE: qh = VELOCITY PRESSURE, kPa)
D
Ø10 STIRRUPS
FOR SIZE AND SPACING GCpf = EXTERNAL PRESSURE COEFFICIENT
GCpi = INTERNAL PRESSURE COEFFICIENT
90º HOOKS
OF HOR. & VERT. BARS
VERIFY DEPRESSION

@ 150 O.C. SEE CONSTRUCTION NOTES. 30 BAR DIA. 30 BAR DIA.

90º END HOOKS L1
D. SEISMIC LOAD (NSCP 2010 )
DOWEL

(MIN) (MIN)
D = FOR BEAM

Cvl
400

t = FOR SLAB

DOWEL BARS TO MATCH V=

CHB WALL RT W ( DESIGN BASE SHEAR )
MAIN BAR END HOOKS STIRRUP AND TIE HOOKS
CHB HOR BARS
V max =
2.50 Cal
W Vmin = 0.11 CalW (ALL GRADE) (ALL GRADE)
2- Ø12 TOP BARS R
0.80 ZNvl W (ZONE 4) BAR SIZE DIAMETER 180 HOOK BAR SIZE DIAMETER 180 HOOK 90 HOOK
200

OPENING Vmin =
1- Ø10 VERT. R ( DEFORMED) ( mm) ( DEFORMED) ( mm)
D + 2db L L D + 2db L L
BARS TYPICAL 2- Ø12 TOP BARS WHERE: W= TOTAL DEAD LOAD
10mmØ 60 75 125 150 10mmØ 40 125 85 100
D = FOR BEAM T = NATURAL PERIOD = C t (h n) ;
2t = FOR SLAB WHERE: C = NUMERICAL COEFFICIENT 12mmØ 75 100 150 200 12mmØ 50 165 115 115
30 BAR DIA. h = BUILDING HEIGHT 16mmØ 95 125 175 250 16mmØ 65 200 140 150
FIN. FLR. LVL. SECTION (MIN) I = IMPORTANCE FACTOR = 1.50
R = NUMERICAL FACTOR = 8.50 20mmØ 115 150 200 300 20mmØ 115 250 165 300
SEISMIC COEFFICIENT Cv = 0.44Nv 25mmØ 150 200 230 450 25mmØ 150 365 230 405
ELEVATION Ca = 0.64 N
TYPICAL DETAIL FOR BEAM NEAR SOURCE FACTOR ( 10km ) Nv = 1.2 28mmØ 240 300 350 550
Na = 1.0
TYP. DET. OF LINTEL BEAM AT CHB WALL OPENING OR SLAB CHANGE SOFFIT Z = SEISMIC ZONE = 0.40 ( ZONE 4 )
32mmØ 300 335 450 600

S = SOIL TYPE = D

PROJECT NAME AND LOCATION: SHEET CONTENTS: DRAFTED: REVIEWED: SUBMITTED: RECOMMENDED: APPROVED: CONCURRED: SET NO. SHEET NO.
REPUBLIC OF THE PHILIPPINES
DEPARTMENT OF PUBLIC WORKS AND HIGHWAYS CY 2024 DPWH INFRASTRUCTURE PROGRAM MA. LANI J. GALLEGO
REGIONAL OFFICE VI DETAILED ENGINEERING DESIGN PLAN FOR ENGINEERING ASST. S-2 7
ILOILO 2ND DISTRICT ENGINEERING OFFICE CONSTRUCTION (COMPLETION) OF MULTI- PURPOSE BUILDING OF GENERAL NOTES
JERMAIN CEM L. DEQUILLA EDUARD B. OREN ALLAN REY R. PAJIMNA
BALABAG, DUMANGAS, ILOILO BARANGAY IMPALIDAN, CALINOG, ILOILO PREPARED: SHARYN C. SUPEÑA 2 7 15
CALINOG, ILOILO GIZA P. PLAZA ENGINEER II OIC-CHIEF, PLANNING AND DESIGN SECTION OIC-ASSISTANT DISTRICT ENGINEER DISTRICT ENGINEER BARANGAY CAPTAIN
ENGINEER II DATE DATE DATE DATE DATE
L. MEDIANA
 SCHEDULE OF SPAN PER COLUMN
NAME LENGTH SPAN ( LS)
SPAN-1 4500 MM
SPAN-2 4500 MM
SPAN-3 5000 MM
SPAN-3&4 10000 MM
SPAN-4 5000 MM
SPAN-5 4500 MM SCHEDULE OF FOOTING
SPAN-6 4500 MM
FOOTING DIMENSIONS
FLOOR LENGTH = 28000 MM REINFORCEMENT
in mm
FLOOR WIDTH = 14000 MM FOOTING REMARKS
MARKS
LENGTH WIDTH DEPTH Thickness
(L) (W) (D) ( t) BAR Y BAR X

F-1 1800 1800 1500 300 11-16 mm Ø 11-16 mm Ø SQUARE FOOTING

A B C D E F G
LENGTH

SPAN-1 SPAN-2 SPAN-3 & 4 SPAN-5 SPAN-6

C1/F1 C1/F1 C1/F1 C1/F1 C1/F1 C1/F1

2 TB TB TB TB TB 2
W
NAT. GRADE LNE
COLUMN SCHEDULE
X - BARS
C -1

FOUNDATION LEVEL TO
GROUND FLOOR LEVEL
350

Y - BARS

D
L

350
MAIN BARS : 8 -16 mm Ø

WIDTH
WIDTH

TB
TB

E X I S T I N G S L A B C O U R T

t
TIES :2-10 mm Ø 6@ .050 m., 5 @
0.10 m. 5 @ 0.15 m.REST @ 0.20 M.
0.50 m. THK. GRAVEL BED

(PLAN ) ( SECTION )

TB TB TB TB TB TB
1 1
C1/F1 C1/F1 C1/F1 C1/F1 C1/F1 C1/F1 C1/F1
2 - 16MMØ
SPAN-1 SPAN-2 SPAN-3 SPAN-4 SPAN-5 SPAN-6 200 200

LENTGH 2 - 16MMØ 2 - 16MMØ

400

400
2 - 16MMØ 2 - 16MMØ
A B C D E F G @ SUPPORT @ MIDSPAN
2 - 16MMØ
(SECTION)

1 FOUNDATION PLAN (PLAN)

S-3 SCALE 1:150 M L

USE 10 MM Ø TIES 6 AT 50MM M..5 AT 100 MM, 5 AT 150 MM REST AT 200 MM TO CENTER

2 TIETIE
BEAM
BEAMDETAIL
DETAIL
S-3 SCALE 1:30 M

PROJECT NAME AND LOCATION: SHEET CONTENTS: DRAFTED: REVIEWED: SUBMITTED: RECOMMENDED: APPROVED: CONCURRED: SET NO. SHEET NO.
REPUBLIC OF THE PHILIPPINES
DEPARTMENT OF PUBLIC WORKS AND HIGHWAYS CY 2024 DPWH INFRASTRUCTURE PROGRAM FOUNDATION PLAN, MA. LANI J. GALLEGO
REGIONAL OFFICE VI DETAILED ENGINEERING DESIGN PLAN FOR TIE BEAM DETAIL, ENGINEERING ASST. S-3 8
SCHEDULE OF SPAN
ILOILO 2ND DISTRICT ENGINEERING OFFICE CONSTRUCTION (COMPLETION) OF MULTI- PURPOSE BUILDING OF PER COLUMN,
JERMAIN CEM L. DEQUILLA EDUARD B. OREN ALLAN REY R. PAJIMNA
BALABAG, DUMANGAS, ILOILO BARANGAY IMPALIDAN, CALINOG, ILOILO SCHEDULE OF FOOTING, PREPARED: SHARYN C. SUPEÑA 3 7 15
CALINOG, ILOILO SCHEDULE OF COLUMN,
GIZA P. PLAZA ENGINEER II OIC-CHIEF, PLANNING AND DESIGN SECTION OIC-ASSISTANT DISTRICT ENGINEER DISTRICT ENGINEER BARANGAY CAPTAIN
PLAN AND SECTION
ENGINEER II DATE DATE DATE DATE DATE
L. MEDIANA
 2 s- 75MM X 75MM X 6MM
2 s- 75MM X 75MM X 6MM
2 s- 75MM X 75MM X 6MM
TOP CHORD BAR
BOTTOM CHORD BAR
2 s-50MM X 50MM X 6MM 2 s-50MM X 50MM X 6MM 6MMX 550MM X 120MM
VERTICAL MEMBER BAR SPOT DETAIL 5 WELDED GUSSET PLATE (TYP.)
DIAGONAL MEMBER BAR
LENGTH S-4

475 600 600 600 600 600 600 600 600 600 600 600 600 600 600 600 600 600 600 600 600 600 600 600 600 600 600 600 600 475 2 s- 50MM X 50MM X 6MM
WEB MEMBER BAR
600

600

600
542

542
150 MMX 300MM X 6MM
GUSSET PLATE (TYP.) SPOT DETAIL 6
SPOT DETAIL 4
S-4 3 SEE CORBEL DETAIL
S-4
1488

1488
S-5
2 s- 75MM X 75MM X 6MM
REFER TO BRACKET DETAIL LENGTH LENGTH REFER TO BRACKET DETAIL
946

946
1500 1500

LENGTH

3 STEEL BEAM 1 (SB-1)DETAIL 8 SECTION OF STEEL BEAM (SB-1)

STEEL BEAM 1(SB-1) DET.
S-4 SCALE 1:40 M S-4 SCALE 1:10 M

6MM THK GUSSET PLATE

WELDED JOINT (TYP.)

112

2∠s- 75MMX 75MMX6MM 2∠s- 75MMX 75MMX6MM 2∠s- 75MMX 75MMX6MM 2∠s- 75MMX 75MMX6MM

140
TOP CHORD BAR BOTTOM CHORD BAR TOP CHORD BAR BOTTOM CHORD BAR

600
LENGTH LENGTH
500 500 500 500 500 500 500 500 325 500 500 500 500 500 500 500 500 500 500 500 500 500 500 325

654

542
500
600

1488
150 MMX 300MM X 6MM

140
150 MMX 300MM X 6MM
20MM X 12MM 6MM THK.
GUSSET PLATE (TYP.)

34
GUSSET PLATE (TYP.)

946

20
GUSSET PLATE

2∠s-75MMX75MM X 6MM
2 STEEL BEAM 3 (SB-3)DETAIL BRACKET BAR
1 STEEL BEAM
STEEL BEAM 2(SB-2) DET.
2 (SB-2)DETAIL S-4 SCALE 1:40 M
FULLY WELD
4-12 MM Ø X 300MM
LONG BENT ANCHOR
1500
S-4 SCALE 1:40 M
6 SPOT DETAIL BOLTS W/ NUTS
AND WASHERS
250 MM X 250 MM X 12MM
STEEL BASE PLATE
S-4 SCALE 1:10 M

7 STEEL BRACKET DETAIL

S-4 SCALE 1:10 M

SCHEDULE OF STEEL BEAM 6MM THK GUSSET PLATE

WELDED JOINT (TYP.)
6MM THK GUSSET PLATE
WELDED JOINT (TYP.)
NUMBER OF NUMBER OF TOTAL NUMBER
CODE LENGTH HEIGHT DIAGONAL MEMBER VERTICAL MEMBER OF STEEL BEAM-1
14000 MM 600 MM 24 25 2
15000 MM 600 MM 24 25 2 300
SB-1 16000 MM 600 MM 24 25 2
17000 MM 600 MM 26 27 2

140
18000 MM 600 MM 28 29 2

140
4000 MM 600 MM 8 9 10
SB-2 4500 MM 600 MM 10 11 10 300
5000 MM 600 MM 10 11 10
FULLY WELD
6000 MM 600 MM 12 13 1
7000 MM 600 MM 14 15 1 FULLY WELD
SB-3 8000 MM 600 MM 16 17 2
9000 MM 600 MM 18 19 1 4 SPOT DETAIL 5 SPOT DETAIL
10000 MM 600 MM 20 21 1 S-4 SCALE 1:10 M S-4 SCALE 1:10 M

PROJECT NAME AND LOCATION: SHEET CONTENTS: DRAFTED: REVIEWED: SUBMITTED: RECOMMENDED: APPROVED: CONCURRED: SET NO. SHEET NO.
REPUBLIC OF THE PHILIPPINES
DEPARTMENT OF PUBLIC WORKS AND HIGHWAYS CY 2024 DPWH INFRASTRUCTURE PROGRAM SCHEDULE OF STEEL BEAM, MA. LANI J. GALLEGO
REGIONAL OFFICE VI DETAILED ENGINEERING DESIGN PLAN FOR DETAIL OF SB -1,
DETAIL OF SB-2,
ENGINEERING ASST. S-4 9
ILOILO 2ND DISTRICT ENGINEERING OFFICE CONSTRUCTION (COMPLETION) OF MULTI- PURPOSE BUILDING OF DETAIL OF SB -3,
JERMAIN CEM L. DEQUILLA EDUARD B. OREN ALLAN REY R. PAJIMNA
BALABAG, DUMANGAS, ILOILO BARANGAY IMPALIDAN, CALINOG, ILOILO SPOT DETAILS,
PREPARED: SHARYN C. SUPEÑA 4 7 15
CALINOG, ILOILO STEEL BRACKET, ENGINEER II OIC-CHIEF, PLANNING AND DESIGN SECTION OIC-ASSISTANT DISTRICT ENGINEER DISTRICT ENGINEER BARANGAY CAPTAIN
SECTION OF STEEL BEAM GIZA P. PLAZA
ENGINEER II DATE DATE DATE DATE DATE
L. MEDIANA
 1∠- 5MM THK. X38MMX38MM 1∠-5MM THK. X38MMX38MM
TOP & BOTTOM CHORD VERT. MEMBERS
1∠- 5MM THK. X38MM
1∠-5MM THK. X38MMX38MM END FLASHING
X38MM TOP & BOTTOM
VERT. MEMBERS
CHORD
1∠- 5MM THK. X38MMX38MM
C- PURLINS
TOP & BOTTOM CHORD
A B C D E F G FASCIA COVER
0.60 MM THK. 0.551MM THK. PRE- PAINTED P.G.I.FASCIA COVER FIN. (GAUGE 24)

400
0.551 MM THK. P.G.I. SHEETS FASCIA COVER

400
LENGTH P.G.I. SHEETS FASCIA FRAME
(GAUGE 24) 1∠- 5MM THK. X38MMX38MM
FASCIA COVER VERT. MEMBERS
1000 SPAN-1 SPAN-2 SPAN-3 SPAN-4 SPAN-5 SPAN-6 1000
400 400 400 (SECTION)
400 400 400 400 ( SECTION) (PLAN)
100MM X 50MM X 2MM 12MMØ CROSS BRACING BAR
C-PURLINS AT ± 649 MM (SEE DETAIL) FASCIA FRAME
FASCIA 2 DETAIL
FRAME 2 DETAIL
7
SEE FASCIA FRAME-2 DETAIL
S-5 SCALE 1:20 M 6 FASCIA FRAME 1 DETAIL
1500

1500
S-5 SCALE 1:20 M

2 SB-2 SB-2 SB-3 SB-2 SB-2

2
12 MM Ø CROSS BRACING BAR W/
STD. 16 MM Ø TURN BUCKLE
SCHEDULE OF SPAN PER COLUMN
12 MM Ø CROSS BRACING BAR
NAME LENGTH SPAN ( LS) 140 FULLY WELD TO BUCKLE PLATE
( CR R LEN

SPAN-1 4500 MM
BA
OSS GTH

±35

SPAN-2 4500 MM
SEE FASCIA FRAME-1 DETAIL

SEE FASCIA FRAME-1 DETAIL

BRA )

00

L
CIN

SPAN-3 5000 MM
G

TOP OF G.I. PIPE TRUSS

SAG ROD

SAG ROD
SAG ROD

SAG ROD

SAG ROD

SAG ROD
TRUSS

TRUSS
TRUSS
TRUSS

TRUSS
WIDTH

WIDTH
SPAN-3&4 10000 MM

TRUSS

TRUSS
SB-1

SB-1
CG
CG

CG

CG

CG

CG

50
( CR R LEN
BA

SPAN-4 5000 MM 12 MM THK.

OSS GTH

WELDED JOINT

200

100
BUCKLE PLATE
610

SPAN-5 4500 MM
BRA )

WELDED JOINT
CIN

50
SPAN-6 4500 MM
G

FLOOR LENGTH = 28000 MM 12 MM Ø CROSS BRACING BAR

FULLY WELD TO BUCKLE PLATE
NOTE:TO BE APPLIED TO ALL FLOOR WIDTH = 14000 MM 12 MM Ø CROSS BRACING BAR
CROSS BRACING FULLY WELD TO BUCKLE PLATE

CONN. DETAIL OF CROSS

L
SB-2 SB-2 SB-2 SB-2 SB-2 SB-2
5 BRACING ON TRUSSES
1 1 S-5 SCALE 1:8 M
1500

1500
SEE FASCIA FRAME-2 DETAIL CONN. DETAIL OF CROSS
12MMØ TENSION BAR (SEE DETAIL)
1000 SPAN-1 SPAN-2 SPAN-3 SPAN-4 SPAN-5 SPAN-6 1000
4 BRACING ON COLUMN
12 MM X 500MMX300 MM
STEEL BASE PLATE S-5 SCALE 1:8 M
LENGTH ( WELDED TO BOTTOM
OF STEEL BEAM)
2- 12MMØ X300MM LONG
A B C D E F G BEND ANCHOR BOLTS W/
NUTS AND WASHERS ON
6- 12MMØ X300MM LONG
BEND ANCHOR BOLTS W/
12MMX600MMX300MM STEEL
NUTS AND WASHERS
BASE PLATE ( WELDED FIN.)

2 ROOF FRAMING PLAN 12 MM X 500MMX300 MM

S-5 SCALE 1:150 M TOP OF COLUMN STEEL BASE PLATE
2- 12MMØ X300MM LONG ( WELDED TO BOTTOM
BEND ANCHOR BOLTS W/ OF STEEL BEAM)
NUTS AND WASHERS ON
12MMX600MMX300MM STEEL
BASE PLATE ( WELDED FIN.) 6- 12MMØ X300MM LONG
50MMØ G.I. PIPE (SCHED 40 )TOP AND 38MMØ G.I. PIPE (SCHED 40 ) BEND ANCHOR BOLTS W/
BOTTOM CHORD BAR WEB MEMBERS BAR NUTS AND WASHERS

1000
50MMØ G.I PIPE
L TOP CHORD

300
38MMØ G.I. PIPE COLUMN
500 500 500 500 500 500 500 500 500 500 WEB MEMBERS

300
4-16MM Ø BARS W/

400
10MMØ TIES AT
100MM O.C. BOTTOM OF
300

500 STEEL BEAM

50MMØ G.I PIPE
BOTTOM CHORD 3 CORBEL DETAIL
150 150 (SECTION) S-5 SCALE 1:150 M
1 CENTER GIRT (CG) DETAIL COLUMN 500
S-5 SCALE 1:16 M

CORBEL DETAIL
PROJECT NAME AND LOCATION: SHEET CONTENTS: DRAFTED: REVIEWED: SUBMITTED: RECOMMENDED: APPROVED: CONCURRED: SET NO. SHEET NO.
REPUBLIC OF THE PHILIPPINES CENTER GIRT,
DEPARTMENT OF PUBLIC WORKS AND HIGHWAYS CY 2024 DPWH INFRASTRUCTURE PROGRAM
ROOF FRAMING PLAN,
SCHEDULE OF
MA. LANI J. GALLEGO
REGIONAL OFFICE VI DETAILED ENGINEERING DESIGN PLAN FOR SPAN PER COLUMN ENGINEERING ASST. S-5 10
ILOILO 2ND DISTRICT ENGINEERING OFFICE CONSTRUCTION (COMPLETION) OF MULTI- PURPOSE BUILDING OF FASCIA FRAME 1 DETAIL,
JERMAIN CEM L. DEQUILLA EDUARD B. OREN ALLAN REY R. PAJIMNA
BALABAG, DUMANGAS, ILOILO BARANGAY IMPALIDAN, CALINOG, ILOILO
FASCIA FRAME 2 DETAIL,
CONNECTION DETAIL OF CROSS
PREPARED: SHARYN C. SUPEÑA 5 7 15
CALINOG, ILOILO BRACING ON TRUSSES,
GIZA P. PLAZA ENGINEER II OIC-CHIEF, PLANNING AND DESIGN SECTION OIC-ASSISTANT DISTRICT ENGINEER DISTRICT ENGINEER BARANGAY CAPTAIN
CONNECTION DETAIL OF CROSS
BRACING ON COLUMN ENGINEER II DATE DATE DATE DATE DATE
L. MEDIANA
 LENGTH

12MMØ (PLAIN
BAR) SAG ROD
50MMØ G.I. PIPE (SCHED 40 )
TOP CHORD BAR 0.50MM THK. PRE PAINTED HI- RIB
1 50MMØ G.I. PIPE (SCHED 40 )
CURVE TYPE LONG SPAN ROOFING 2
38 ROWS - 100MM X 50MM X 2MM C-PURLINS
BOTTOM CHORD BAR AT ±649 W/ 50MMX50MM BAR CLEATS

400
38 MM Ø G.I. PIPE
LATERAL MEMBER

LENGTH 2-38 MM Ø G.I. PIPE

DIAGONAL MEMBER
3500
3100 600 CE
I S TAN
.D
TYP

SPOT DETAIL 2
S-6

1 MAIN TRUSS DETAIL

S-6 SCALE 1:30 M
30
10

0
0

LENGTH LENGTH

1500 LENGTH 1500

LENGTH

SCHEDULE OF TRUSS & MEMBERS

NUMBER OF NUMBER OF
FLOOR AREA EAVES NUMBER OF LATERAL MEMBER DIAGONAL MEMBER TOP CHORD BOTTOM CHORD TOTAL NUMBER
PURLINS (PER CURVE TRUSS) ARC LENGTH ARC LENGTH OF TRUSSES
LENGTH WIDTH FRONT REAR LEFT RIGHT (PER CURVE TRUSS)
1500 1500 1000 1000
(LENGTH) MM 14000 MM 36 35 70 20146 MM 20505 MM 7
MM MM MM MM
1500 1500 1000 1000
(LENGTH) MM 15000 MM 36 35 70 20784 MM 21035 MM 7
MM MM MM MM
1500 1500 1000 1000
(LENGTH) MM 16000 MM 38 37 74 21506 MM 21691 MM 7
MM MM MM MM
1500 1500 1000 1000
(LENGTH) MM 17000 MM 40 39 78 22282 MM 22425 MM 7
MM MM MM MM
1500 1500 1000 1000
(LENGTH) MM 18000 MM 40 39 78 23098 MM 23211 MM 7
MM MM MM MM

TOP CHORD TOP CHORD

(FULLY WELDED) (FULLY WELDED)

LATERAL MEMBER 2-BOTTOM CHORDS (FULLY

0.05 0.05 TOP CHORD
(FULLY WELDED ) WELDED TO BASE PLATE)
50 100 50 (FULLY WELDED)

LATERAL MEMBER 2-BOTTOM CHORDS (FULLY LATERAL MEMBER 50mmØ G.I. PIPE WELDED
38MMØ G.I. PIPE(SCHED 40 ) WELDED TO BASE PLATE) (FULLY WELDED )
(FULLY WELDED ) 2-BOTTOM CHORDS (FULLY
DOUBLE WEB MEMBERS
WELDED TO BASE PLATE)
50mmØ G.I. PIPE WELDED
50mmØ G.I. PIPE WELDED
LATERAL MEMBER(FULLY
WELDED ) 50mmØ G.I. PIPE WELDED
8-12MMX300MM LONG BENT FULLY WELDED
ANCHOR BOLTS W/ STD.
90

8-12MMX300MM LONG BENT NUTS & WASHERS

ANCHOR BOLTS W/ STD.
50 76 50

STEEL BEAM
NUTS & WASHERS 300X300X12MM BASE PLATE 8-12MMX300MM LONG BENT
ANCHOR BOLTS W/ STD. FULLY WELDED
NUTS & WASHERS
∠ BAR STEEL BEAM
COLUMN
90

300X300X12MM BASE PLATE

BOTTOM CHORD (FULLY
WELDED TO BASE PLATE) SECTION
TOP CORD (FULLY WELDED) COLUMN
SIDE ELEVATION
PLAN STEEL BEAM / TRUSS
2 TYP. ANCHORAGE DETAIL FRONT ELEVATION
3 ANCHORAGE DETAIL
S-6 SCALE 1:10 M S-6 SCALE 1:10 M

PROJECT NAME AND LOCATION: SHEET CONTENTS: DRAFTED: REVIEWED: SUBMITTED: RECOMMENDED: APPROVED: CONCURRED: SET NO. SHEET NO.
REPUBLIC OF THE PHILIPPINES
DEPARTMENT OF PUBLIC WORKS AND HIGHWAYS CY 2024 DPWH INFRASTRUCTURE PROGRAM MA. LANI J. GALLEGO
TYPICAL ANCHORAGE DETAIL
REGIONAL OFFICE VI DETAILED ENGINEERING DESIGN PLAN FOR STEEL BEAM/ TRUSSES ENGINEERING ASST. S-6 11
ILOILO 2ND DISTRICT ENGINEERING OFFICE CONSTRUCTION (COMPLETION) OF MULTI- PURPOSE BUILDING OF ANCHORAGE DETAIL,
JERMAIN CEM L. DEQUILLA EDUARD B. OREN ALLAN REY R. PAJIMNA
BALABAG, DUMANGAS, ILOILO BARANGAY IMPALIDAN, CALINOG, ILOILO SCHEDULE OF TRUSSES
AND MEMBERS,
PREPARED: SHARYN C. SUPEÑA 6 7 15
CALINOG, ILOILO MAIN TRUSS DETAIL GIZA P. PLAZA ENGINEER II OIC-CHIEF, PLANNING AND DESIGN SECTION OIC-ASSISTANT DISTRICT ENGINEER DISTRICT ENGINEER BARANGAY CAPTAIN
ENGINEER II DATE DATE DATE DATE DATE
L. MEDIANA
 50MM Ø SCH. 40 G.I. PIPE
TOP & BOTTOM CHORD

38MM Ø SCH. 40 G.I. PIPE

WEB MEMBER

50MM Ø SCH. 40 G.I.P 2∠s- 75mmx75mmx6mm

TOP CHORD DIAGONAL BAR

38MM Ø SCH. 40 G.I.P 6

WEB MEMBER S-7
2000 50MM Ø SCH. 40 G.I.P
4MM STEEL PLATE TOP CHORD
STABILIZER, BOTH SIDES

CENTER GIRT
( WELDED JOINT ) CENTER GIRT
CENTER GIRT

4MM STEEL PLATE 50MM Ø SCH. 40 G.I.P

2∠s- 75mmx75mmx
50MM Ø SCH. 40 G.I.P BOTTOM CHORD

BOTTOM CHORD
STABILIZER, BOTH SIDES 150MMX150MMX4MM 6mm DIAGONAL BAR
( WELDED JOINT ) BOTTOM CHORD
STEEL PLATE ( WELDED ON OPPOSITE DIRECTION
JOINT)

0.02
5

8
3.5
S-7
0.02

150MMX150MMX4MM

0.02
STEEL PLATE ( WELDED 250 MM RADIUS X 12MM

0.02
JOINT) THK. STEEL PLATE

STEEL
2∠s- 75mmx75mmx6mm 5 TOP VIEW BEAM
DIAGONAL BAR ( WELDED
S-7 SCALE 1: 5 M.
150MMX150MMX4MM JOINT)
STEEL PLATE (WELDED JOINT)

4MM STEEL PLATE

STABILIZER, BOTH SIDES (WELDED JOINT)
6 BRACING DETAIL (INSIDE)
S-7 SCALE 1:50 M
5 BRACING DETAIL SECTION
2∠s- 75mmx75mmx6mm
DIAGONAL BAR (WELDED JOINT) S-7 SCALE 1:5 M

4 BRACING ISOMETRIC
S-7 SCALE 1:5 M

2∠s- 75mmx75mmx
6mm DIAGONAL BAR
ON OPPOSITE DIRECTION
6MMØ J-BOLTS W/
STD. NUTS AND WASHERS 3.32 3.32
ANCHORED TO C-PURLINS
CENTER GIRT

50 MM X 50 MM ANGLE
BAR CLEATS ( WELDED FIN.)

LC-100MM X 50MM X 20MM X 2.0MM

SPACED @ ±600MM O.C.
50 MM X 100 MM X 2.00MM C - PURLINS
WELDED TO TOP CHORD
12MMØ X ±600MM PLAIN BAR SAG ROD
(THREADED W/ NUTS & WASHER ON
BOTH SIDE)

3.22
3.02
2∠s- 75mmx75mmx6mm
DIAGONAL BAR
±6
00
MM
O.C 250 MM RADIUS X 12MM
.

45°

45°
THK. STEEL PLATE

12 MM Ø PLAIN BAR (SAG ROD)

M STAGGERED AT 50 MM W/ STD
±6
00 50M NUTS & WASHERS
MM

3.
72
O.C
.
STEEL
BEAM

1 SAG ROD ISOMETRIC CONNECT. DET. OF SAG ROD,

S-7 DRAWN NOT TO SCALE 2 CONNECT.
CLEATS, DET.&OF
J-BOLTS SAG ROD/
PURLINS 3 BRACING DETAIL (OUTSIDE)
S-7 DRAWN NOT TO SCALE
S-7 SCALE 1:50 M

PROJECT NAME AND LOCATION: SHEET CONTENTS: DRAFTED: REVIEWED: SUBMITTED: RECOMMENDED: APPROVED: CONCURRED: SET NO. SHEET NO.
REPUBLIC OF THE PHILIPPINES
SAG ROD ISOMETRIC,
DEPARTMENT OF PUBLIC WORKS AND HIGHWAYS CY 2024 DPWH INFRASTRUCTURE PROGRAM CONNECTION DETAIL MA. LANI J. GALLEGO
REGIONAL OFFICE VI DETAILED ENGINEERING DESIGN PLAN FOR OF SAG ROD,
CLEATS,
ENGINEERING ASST. S-7 12
ILOILO 2ND DISTRICT ENGINEERING OFFICE CONSTRUCTION (COMPLETION) OF MULTI- PURPOSE BUILDING OF J-BOLTS & PURLINS,
JERMAIN CEM L. DEQUILLA EDUARD B. OREN ALLAN REY R. PAJIMNA
BALABAG, DUMANGAS, ILOILO BARANGAY IMPALIDAN, CALINOG, ILOILO BRACING DETAIL (OUTSIDE),
PREPARED: SHARYN C. SUPEÑA 7 7 15
CALINOG, ILOILO BRACING DETAIL (INSIDE), ENGINEER II OIC-CHIEF, PLANNING AND DESIGN SECTION OIC-ASSISTANT DISTRICT ENGINEER DISTRICT ENGINEER BARANGAY CAPTAIN
BRACING ISOMETRIC, GIZA P. PLAZA
BRACING DETAIL SECTION ENGINEER II DATE DATE DATE DATE DATE
L. MEDIANA
 2-16 mm Ø HANDLE BARS

10 mm Ø BARS, EW. 480

100
40 400 40

REMOVABLE CB COVER

60 480 60

A B C D E F G INLET
100 mm Ø PVC DOWNSPOUT

LENGTH 100 mm Ø PVC DOWNSPOUT

100 mm THK. CHB WALL W/ 10 mm Ø
HORIZONTAL BARS @ 600 mm O.C (TYPICAL)
150 mm Ø PVCDP (2% SLOPE)
L/S-1 L/S-2 L/S-3&4 L/S-5 L/S-6 60 60
150 mm Ø PVC DP (2% SLOPE) 150 mm Ø PVC DP (2% SLOPE) 40 FIN. GRADE LINE
40
OPENING (VERIFY)
TO DRAINAGE

100
60
100
150MM Ø PVCSDP 150MM Ø PVCSDP 150MM Ø PVCSDP 150MM Ø PVCSDP 150MM Ø PVCSDP ( VERIFY) 150 mm Ø PVCDP (2% SLOPE)
CB CB CB CB CB CB
2 2
INLET

600
400
600
INLET OUTLET
OUTLET

200

95
100
100

60
REMOVABLE R.C. 4-12 mm Ø BARS, E.W.
100 100 COVER WITH 2-16 mm Ø 150 mm Ø PVC DP 100 400 100
150
HANDLE BAR (2% SLOPE)
400 600
600

3 DETAIL OF SECTION
2 DETAIL OF CATCH BASIN P-1 SCALE 1:20 M
P-1 SCALE 1:20 M
A
WIDTH

WIDTH
RD

B
2 DS RD

C
CB 15 DS RD
0M
M ØP
VC
SD
CB P 15 DS
D
0M
MØ
PV
CSD
CBP F
RD
1 1 RD
150
MM
ØP G
CB CB CB CB CB CB CB 1 VC
SD
P
DS RD
150MM Ø PVCSDP 150MM Ø PVCSDP 150MM Ø PVCSDP
L/S-1 L/S-2 L/S-3
150MM Ø PVCSDP 150MM Ø PVCSDP
L/S-5
150MM Ø PVCSDP
L/S-6 L/S-7
TO DRAINAGE
( VERIFY)
DS RD H
C CB 15 DS RD
0M
150B MØ
LENGTH MM DS RD PV
ØP CS
VC D
SD CB P 15 DS
P150CB
A MM
Ø
0M
MØ
PV
CS
PV DS RD
A B C D E F G CS
DP1
50M CB
D
CBP
TO
( V DRAI
B MØ
P
ER NA
IFY GE
)
VC DS
SD RD
LEGEND: C
1P50
MM C
ØPB
2
SDP- (150 MM Ø PVC ) STORM DRAINAGE PIPE VC
1 CATCH BASIN LAYOUT P-1
SD
P15 DS RD
RD - (75MM Ø PVC ) ROOF DRAIN
P-1 SCALE 1:150 M 2 C
S A
D
0M
M ØP C
VC B
DS - (75MM Ø PVC ) DOWN SPOUT
CA TC SD
P15
0M
DS RD
LE HB F
M ØP
VC CB

CATCH BASIN LAYOUT 1: 1

5 0M AS
SD1
P50
M MØ DS
. IN G
PV
CS C
DP B
ISO TO
( V DRAI 1
ME H
ER NA
IFY GE
)

TR
IC

PROJECT NAME AND LOCATION: SHEET CONTENTS: DRAFTED: REVIEWED: SUBMITTED: RECOMMENDED: APPROVED: CONCURRED: SET NO. SHEET NO.
REPUBLIC OF THE PHILIPPINES
DEPARTMENT OF PUBLIC WORKS AND HIGHWAYS CY 2024 DPWH INFRASTRUCTURE PROGRAM MA. LANI J. GALLEGO
REGIONAL OFFICE VI DETAILED ENGINEERING DESIGN PLAN FOR CATCH BASIN LAYOUT,
DETAIL OF CATCH BASIN,
ENGINEERING ASST. P-1 13
ILOILO 2ND DISTRICT ENGINEERING OFFICE CONSTRUCTION (COMPLETION) OF MULTI- PURPOSE BUILDING OF DETAIL OF SECTION,
JERMAIN CEM L. DEQUILLA EDUARD B. OREN ALLAN REY R. PAJIMNA
BALABAG, DUMANGAS, ILOILO BARANGAY IMPALIDAN, CALINOG, ILOILO CATCH BASIN ISOMETRIC
PREPARED: SHARYN C. SUPEÑA 1 1 15
CALINOG, ILOILO GIZA P. PLAZA ENGINEER II OIC-CHIEF, PLANNING AND DESIGN SECTION OIC-ASSISTANT DISTRICT ENGINEER DISTRICT ENGINEER BARANGAY CAPTAIN
ENGINEER II DATE DATE DATE DATE DATE
L. MEDIANA
 GENERAL NOTES LEGEND

1. ALL ELECTRICAL WORKS SHALL COMPLY IN ACCORDANCE WITH THESE SYMBOL DESCRIPTION
PLANS AND SPECIFICATIONS. THE APPLICABLE PROVISIONS OF THE LATEST
11W LED CEILING PINLIGHT
EDITION OF THE PHILIPPINE ELECTRICAL (PEC). THE RULES AND REGULATION
OF THE LOCAL ENFORCING AUTHORITY AND THE REQUIREMENTS OF THE
PB 150W IP65 LED FLOODLIGHT
2 2
LOCAL POWER COMPANY. THE ELECTRICAL WORKS SHALL BE UNDER
IMMEDIATE SUPERVISION OF A DULY REGISTERED ELECTRICAL ENGINEER. 50W IP65 LED FLOODLIGHT

2. THE ELECTRICAL SERVICE IS 1-PHASE, 2-WIRE, 230 V AC, 60 Hz. S 1-GANG SWITCH

3. WIRING METHOD SHALL BE AS FOLLOWS: Sab 2-GANG SWITCH

1
a. FEEDERS AND RISERS - INTERMEDIATE METALLIC CONDUIT
b. LIGHTING POWER - POLYVINYL CHLORIDE CONDUIT Scde 3-GANG SWITCH
BRANCH CKT., & AUXILIARY SCH. 40
S3w 3-WAY SWITCH
4. ALL WIRES SHALL BE COPPER AND THERMOPLASTIC INSULATED TYPE "THHN"
CIRCUIT BREAKER
UNLESS OTHERWISE INDICATED IN THE PLAN. THE MINIMUM SIZE OF WIRE
FOR POWER AND LIGHTING CIRCUIT HOMERUN SHALL BE 3.5mm² AND

3
DUPLEX CONVENIENCE OUTLET
INSULATED FOR 600 VOLTS. SMALLEST RACEWAY SHALL BE 15mmØ
TRADE/NOMINAL SIZE. MDP
MAIN DISTRIBUTION PANEL BOARD

5. ALL OUTLET BOXES SHALL BE GALVANIZED GUAGE NO. 16 DEEP TYPE WITH PB PANEL BOARD
FACTORY KNOCKOUTS.
M SERVICE METER

2
6. ALL MATERIALS TO BE USED SHALL BE BRAND NEW AND APPROVED TYPE
FOR THE PARTICULAR LOCATION AND PURPOSE OF USAGE. SERVICE ENTRANCE

CIRCUIT HOME RUN

7. GROUNDING SYSTEM SHALL BE PROVIDED TO ALL LIGHTING AND POWER
CIRCUIT AS PER PHILIPPINE ELECTRICAL CODE REQUIREMENT. GROUNDING ELECTRODE
1 1 8. MOUNTING HEIGHT OF WIRING DEVICES SHALL BE AS FOLLOWS: SUB-METER

a. LIGHT SWITCH - 1.20M ABOVE THE FINISH FLOOR. 2 CIRCUIT NUMBER

1 ELECTRICAL PLAN b. CONVENIENCE OUTLET - 0.30M ABOVE THE FINISH FLOOR.
c. PANELBOARD - 2.0M ABOVE THE FINISH FLOOR. CEILING FAN
E-1 SCALE 1: 150 M.
d. FIRE ALARM STATION OUTLET - 1.50M ABOVE THE FINISH FLOOR.
e. SERVICE METER - 1.80M ABOVE THE FINISH GROUND. FACP FIRE ALARM CONTROL PANEL
f. PUSH BUTTON OUTLET - 1.20M ABOVE THE FINISH FLOOR.
g. FIRE ALARM AND VIBRATING BELL - 0.30M BELOW CEILING LINE

60AT, 100AF, 2P, 230V

50W LED FLOODLIGHT 1 2 50W LED FLOODLIGHT

20 20

150W LED FLOODLIGHT 3 20 20 4 SPARE

SPARE 5 20 20 6 SPARE

GROUND TERMINAL 1-8.0mm² BARE COPPER WIRE

4 ONE LINE
ONE LINEDIAGRAM
DIAGRAM
2 SCHEDULE OF LOADS W/ BACKUP COMPUTATION E-1
E-1

3 VOLTAGE DROP CALCULATION

E-1

PROJECT NAME AND LOCATION: SHEET CONTENTS: DRAFTED: REVIEWED: SUBMITTED: RECOMMENDED: APPROVED: CONCURRED: SET NO. SHEET NO.
REPUBLIC OF THE PHILIPPINES
DEPARTMENT OF PUBLIC WORKS AND HIGHWAYS CY 2024 DPWH INFRASTRUCTURE PROGRAM VOLTAGE DROP MA. LANI J. GALLEGO
REGIONAL OFFICE VI DETAILED ENGINEERING DESIGN PLAN FOR
CALCULATION,
SCHEDULE OF LOADS W/
ENGINEERING ASST. E-1 14
ILOILO 2ND DISTRICT ENGINEERING OFFICE CONSTRUCTION (COMPLETION) OF MULTI- PURPOSE BUILDING OF BACK UP COMPUTATION,
PREPARED: RYAN B. SEROJANO JERMAIN CEM L. DEQUILLA EDUARD B. OREN ALLAN REY R. PAJIMNA
BALABAG, DUMANGAS, ILOILO BARANGAY IMPALIDAN, CALINOG, ILOILO ELECTRICAL PLAN,
ONE LINE DIAGRAM,
1 1 15
CALINOG, ILOILO ENGINEER II OIC-CHIEF, PLANNING AND DESIGN SECTION OIC-ASSISTANT DISTRICT ENGINEER DISTRICT ENGINEER BARANGAY CAPTAIN
GENERAL NOTES, LEGEND RYAN B. SEROJANO
ENGINEER II DATE DATE DATE DATE DATE
L. MEDIANA
 PROJECT NAME AND LOCATION: SHEET CONTENTS: SUBMITTED: RECOMMENDED: APPROVED: SET NO. SHEET NO.
REPUBLIC OF THE PHILIPPINES
DEPARTMENT OF PUBLIC WORKS AND HIGHWAYS
BASED ON ROAD SAFETY DESIGN MANUAL
CY 2024 DPWH INFRASTRUCTURE PROGRAM
REGIONAL OFFICE VI DETAILED ENGINEERING DESIGN PLAN FOR BILLBOARD: D.O.21 SERIES OF 2017, PB 15
ILOILO 2ND DISTRICT ENGINEERING OFFICE CONSTRUCTION (COMPLETION) OF MULTI- PURPOSE BUILDING OF DPWH BILLBOARD REVISED GUIDELINES ON THE INSTALLATION OF JERMAIN CEM L. DEQUILLA EDUARD B. OREN ALLAN REY R. PAJIMNA
BALABAG, DUMANGAS, ILOILO BARANGAY IMPALIDAN, CALINOG, ILOILO 1 1 15
CALINOG, ILOILO PROJECT BILLBOARDS OIC-CHIEF, PLANNING AND DESIGN SECTION OIC-ASSISTANT DISTRICT ENGINEER DISTRICT ENGINEER

DATE DATE DATE

L. MEDIANA