Scribd
Upload
25 views3 pages

Nuevo Documento de Texto

This document contains code to control an LED using serial communication. It defines a pin for the LED, sets it as an output in setup(), and in loop() it checks for incoming serial data. If the data is '1' it turns the LED on, if '0' it turns the LED off, printing a message to the serial monitor.

Uploaded by

dibij70167
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as TXT, PDF, TXT or read online on Scribd
25 views3 pages

Nuevo Documento de Texto

This document contains code to control an LED using serial communication. It defines a pin for the LED, sets it as an output in setup(), and in loop() it checks for incoming serial data. If the data is '1' it turns the LED on, if '0' it turns the LED off, printing a message to the serial monitor.

Uploaded by

dibij70167
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as TXT, PDF, TXT or read online on Scribd
You are on page 1/ 3

#include <OneWire.

h>
#include <DallasTemperature.h>

// Data wire is plugged into pin 2 on the Arduino


#define ONE_WIRE_BUS 2

OneWire oneWire(ONE_WIRE_BUS);
DallasTemperature sensors(&oneWire);

void setup(void)
{
Serial.begin(9600);
// Inicializar la comunicación con el sensor
sensors.begin();
}

void loop(void)
{
sensors.requestTemperatures(); // Enviar la petición de temperatura al sensor
float temperatura = sensors.getTempCByIndex(0); // Leer la temperatura en grados
Celsius

// Imprimir la temperatura en el monitor serial


Serial.print("Temperatura: ");
Serial.print(temperatura);
Serial.println(" °C");

delay(1000); // Esperar 1 segundo antes de leer la temperatura nuevamente


}

#include <SoftwareSerial.h>
SoftwareSerial bt(10,11 );

void setup () {
Serial.begin(9600);
bt.begin(38400);

}
void loop(){
if (Serial.available() >0){
bt.write(Serial.read());
}
if (bt.available() >0){
Serial.write(bt.read());
}
}

/*
Software serial multiple serial test
Receives from the hardware serial, sends to software serial.
Receives from software serial, sends to hardware serial.

The circuit:
* RX is digital pin 10 (connect to TX of other device)
* TX is digital pin 11 (connect to RX of other device)

Note:
Not all pins on the Mega and Mega 2560 support change interrupts,
so only the following can be used for RX:
10, 11, 12, 13, 50, 51, 52, 53, 62, 63, 64, 65, 66, 67, 68, 69

Not all pins on the Leonardo and Micro support change interrupts,
so only the following can be used for RX:
8, 9, 10, 11, 14 (MISO), 15 (SCK), 16 (MOSI).

created back in the mists of time


modified 25 May 2012
by Tom Igoe
based on Mikal Hart's example

This example code is in the public domain.

*/
#include <SoftwareSerial.h>

SoftwareSerial mySerial(10, 11); // RX, TX

void setup() {
// Open serial communications and wait for port to open:
Serial.begin(9600);
while (!Serial) {
; // wait for serial port to connect. Needed for native USB port only
}

Serial.println("Goodnight moon!");

// set the data rate for the SoftwareSerial port


mySerial.begin(38400);
mySerial.println("Hello, world?");
}

void loop() { // run over and over


if (mySerial.available()) {
Serial.write(mySerial.read());
}
if (Serial.available()) {
mySerial.write(Serial.read());
}
}

// Definir el pin del LED


int ledPin = 13;

void setup() {
// Inicializar el pin del LED como salida
pinMode(ledPin, OUTPUT);
// Inicializar la comunicación serial a 9600 baudios
Serial.begin(9600);
}

void loop() {
// Verificar si hay datos disponibles en el puerto serial
if (Serial.available() > 0) {
// Leer el byte recibido
char receivedChar = Serial.read();
// Verificar si el byte recibido es '1' (encender el LED)
if (receivedChar == '1') {
digitalWrite(ledPin, HIGH); // Encender el LED
Serial.println("LED encendido");
}
// Verificar si el byte recibido es '0' (apagar el LED)
else if (receivedChar == '0') {
digitalWrite(ledPin, LOW); // Apagar el LED
Serial.println("LED apagado");
}
}
}

You might also like