LS ELECTRIC strives to maximize your profits in gratitude for choosing us as your partner.

Human Machine Interface

XGT PANEL
iXP2 Series
 Safety Precautions

Before using the product…

To use the product safety and effectively, please read this instruction manual thoroughly before
use.

► Please keep to the safety precaution, for it to prevent accidents and

potential danger from occurring.

► Safety precaution is classified into ‘Warming’ and ‘Caution’ and their meanings are as
follows.

Warning Violating the instruction may result in serious personal injury or death.

Caution Violating the instruction may result in slight personal injury or

product damage.

► The indicated illustrations on the product and in the manual have the fallowing meanings.

Be cautions, for danger may be present.

Be cautions, for there is a possibility of an electric shock.

► After reading the instruction manual, keep it handy for quick reference.

1
 Safety Precautions

Design Precautions
Warning
► Install a safety circuit external to the HMI to protect the whole control system in case of
external power supply trouble.
Serious trouble may occur to the entire system due to erroneous output/operation of the HMI.

Design Precautions
Caution
► In/output signal or communication cable should be at least 100mm apart from High-
voltage/power wires.
Otherwise, it may cause erroneous output/operation.

Installation Precautions
Caution
► Use the HMI in an environment that meets the general specification contained in this
manual or datasheet.
Otherwise, it could result in electric shock, fire, erroneous operation or deterioration.

► In case of much vibration in the installed environment, be sure to insulate the HMI from
direct vibration.
Otherwise, it could result in electric shock, fire, erroneous operation.

► Be sure not to let foreign substances such as conductive debris inside the product.
Otherwise, it could result in electric shock, fire, erroneous operation.

► Do not touch the conductive part of the HMI. It may cause an electric shock,
which may cause malfunction.

2
 Safety Precautions

Wiring Precautions

Warning
► Be sure to turn off the HMI and external power before wiring.
Otherwise, it may result in an electric shock or damage to the product.

Caution
► Wire correctly by checking each of the product’s rated voltage and terminal layout.
Otherwise, it may result in fire, electric shock or erroneous operation.

► Tighten terminal screws with specified torque when wiring.

If terminal screws are loose, it may result in short circuits, fire or erroneous operation.

► Use the exclusive HMI 3-type grounding for the FG terminal.

If not grounded, it may result in erroneous operation.

► Be sure not to let any foreign substances such as wiring debris inside the module.
Such debris may cause fire, damage or erroneous operation.

► Tighten the crimp terminal to the specified torque, and crimp the external
connection connector using the specified tool or solder it correctly.

3
 Safety Precautions

Startup and Maintenance Precautions

Warning
► Do not touch the terminals while power is on.
Otherwise, it may cause electric shock or erroneous operation.

► Turn off the HMI and external power when cleaning or tightening the terminal.
Otherwise, it may cause electric shock or erroneous operation.

► Do not charge, disassemble, heat, short circuit, solder, etc. other battery.
Mishandling the battery may cause overheating, crack, fire and may result in injury or fire.

Caution
► Do not disassemble PCB from the product case or modify the product.
Otherwise, it may result in fire, electric shock or erroneous operation.

► When mounting or removing the HMI from the panel, be sure to shut off all
power
being used by the system. It may cause electric shock, malfunction.

► Use cellular phone or walky-talky at least 30cm away from the HMI.
Otherwise, it may result in erroneous operation.

Disposal Precaution

Caution
► When disposing of this product or battery, treat it as industrial waste.
Otherwise, it may cause poisonous pollution or explosion.

4
 Revision History

Revision History

Version Date Contents Revised Location

V1.0 ‘18.01 First Edition -
V1.1 ‘18.08 Add explosion-proof 1. General Instruction
2. System configuration
3. Standard Specification
4. Installation and Wiring
6. Backup file by using storage
7. Maintenance

V1.2 ’19.11 Add features and fix errors 3. Standard Specification

4. Installation and Wiring
5. XGT Panel Menu Explanation
9. Appendix
V1.3 ’20.04 Revision due to the change of company
name

'

※ The number of User’s manual is indicated the right side of the back cover.
ⓒ LS ELECTRIC Co., Ltd2018 All Rights Reserved.

5
 Contents

Chapter 1 General Introduction ...................................................................... 1-1~1-6

1.1 How to use the Instruction Manual ........................................................................................................ 1-1

1.2 Feature .................................................................................................................................................. 1-2
1.3 Terminology .......................................................................................................................................... 1-5
1.4 Specification of product name ............................................................................................................... 1-6

Chapter 2 System Configuration....................................................................... 2-1~2-4

2.1 Part Names ........................................................................................................................................... 2-1

2.2 System Configuration ............................................................................................................................ 2-4

Chapter 3 Standard Specification...................................................................... 3-1~3-4

3.1 General Standards ................................................................................................................................ 3-1

3.2 Function Standards ............................................................................................................................... 3-3

Chapter 4 Installation and Wiring ...................................................................... 4-1~4-9

4.1 Installation ............................................................................................................................................. 4-1

4.1.1 Installation environment............................................................................................................... 4-1
4.1.2 Notice in handling ........................................................................................................................ 4-3
4.1.3 Precautions for panel installation ................................................................................................ 4-3
4.2 Wiring .................................................................................................................................................... 4-6
4.2.1 Power Wiring ............................................................................................................................... 4-6
4.2.2 Ground Wiring ............................................................................................................................. 4-9

Chapter 5 XGT Panel Menu Explanation ......................................................... 5-1~5-39

5.1 Settings.................................................................................................................................................. 5-3

5.1.1 Backlight Setting .......................................................................................................................... 5-3
5.1.2 Touch Setting .............................................................................................................................. 5-5
5.1.3 DateTime Setting ........................................................................................................................ 5-6
5.1.4 Environment Setting ................................................................................................................... 5-7
5.1.5 Ethernet Setting ........................................................................................................................ 5-14
5.1.6 Buzzer Setting ........................................................................................................................... 5-15
5.1.7 Sound Setting ............................................................................................................................ 5-16
5.1.8 XP-Remote Setting ................................................................................................................... 5-17
5.2 Diagnostics .......................................................................................................................................... 5-18
5.2.1 Screen Diagnostic ..................................................................................................................... 5-19
5.2.2 Touch Diagnostic ...................................................................................................................... 5-20
5.2.3 Backup Memory Diagnostic ...................................................................................................... 5-21

6
 Contents

5.2.4 Flash Memory Diagnostic .......................................................................................................... 5-22

5.2.5 USB Memory Diagnostic ........................................................................................................... 5-23
5.2.6 Serial Diagnostic ....................................................................................................................... 5-24
5.2.7 SD Card Diagnostic ................................................................................................................... 5-27
5.2.8 Touch Sensitivity ....................................................................................................................... 5-28
5.3 PLC Information................................................................................................................................... 5-30
5.3.1 PLC Communication Setting ..................................................................................................... 5-31
5.3.2 Connection Information ............................................................................................................. 5-32
5.3.3 PLC Information ........................................................................................................................ 5-33
5.3.4 History of PLC error .................................................................................................................. 5-33
5.3.5 PLC Operation Mode Conversion History ................................................................................. 5-34
5.3.6 History of power off of PLC ....................................................................................................... 5-34
5.3.7 PLC System History Information ............................................................................................... 5-35
5.3.8 N:1 Setting................................................................................................................................. 5-36
5.3.9 Program Monitor ....................................................................................................................... 5-37
5.4 XGT Panel Update .............................................................................................................................. 5-38
5.5 Storage Function ................................................................................................................................ 5-39
5.5.1 Overview .................................................................................................................................... 5-39
5.5.2 Downloading a project using a storage device .......................................................................... 5-40
5.5.3 Uploading a project using a storage device ............................................................................... 5-41
5.5.4 Updating the device using a storage device .............................................................................. 5-42

Chapter 6 Backup files by using Storage Devices …………........................... 6-1~6-7

6.1 Path Structure in case of File Backup.................................................................................................... 6-1

6.2 Operation Setting when there is no space for Backup ........................................................................ 6-5
6.3 Monitoring Connection Status of External Storage Equipment .............................................................. 6-6

Chapter 7 Maintenance .................................................................................. 7-1~7-3

7.1 Maintenance .......................................................................................................................................... 7-1

7.2 Daily Maintenance ................................................................................................................................ 7-1
7.3 Periodical Maintenance ........................................................................................................................ 7-2

Chapter 8 EMC Standard Certification …………………………....................... 8-1~8-3

8.1 Requirement for EMC Standard Certification ........................................................................................ 8-1

8.1.1 CE Standard Certification ............................................................................................................. 8-1
8.1.2 KC Standard Certification ............................................................................................................. 8-2
8.2 Requirement for Low Voltage Command Suitability............................................................................. 8-2
8.2.1 Standard Certification for XGT Panel ........................................................................................... 8-2
8.2.2 Selection of XGT Panel ................................................................................................................ 8-2

7
 Contents

Appendix 1 Troubleshooting ............................................................. App1-1~App1-25

1. Type of Problems ................................................................................................................................App 1-1

2. Problems when Starting ......................................................................................................................App 1-2
3. Problems after the Monitor on.............................................................................................................App 1-4
4. Display Problems of Figure and Object ..............................................................................................App 1-6
5. Communication Problems ..................................................................................................................App 1-9
6. USB Removal of Memory Card........................................................................................................App 1-11
7. External memory recognition………………….................................................................................App 1-12
8. Touch recognition……………………………….................................................................................App 1-12
9. Error Message during Execution of Programs.................................................................................App 1-13

Appendix 2 Dimensions ................................................................... App 2-1~App2-4

1. iXP2-08xxA/D................................................................................................................................... App 2-1

2. iXP2-10xxA/D................................................................................................................................... App 2-2
3. iXP2-12xxA/D................................................................................................................................... App 2-3
4. iXP2-15xxA/D................................................................................................................................... App 2-4

Appendix 3 Warranty and Environmental Policy ............................................ App 3-1

1. Warranty contents........................................................................................................................... App 3-1

2. Environmental Policy...................................................................................................................... App 3-1

8
 Chapter 1 Overview

Chapter 1 Overview

1.1 How to use the Instruction manual

Sequence Item Contents

Chapter1 Overview It describes and provides information about this manual.

Chapter2 System Configuration It describes features and system configurations for each XGT Panel.
Performance
Chapter 3 It describes XGT Panel and system configuration for each XGT Panel.
Specifications
It describes the installation, wiring and precautions for reliability of the PLC
Chapter4 Installation and Wiring
system.
XGT Panel Menu
Chapter 5 It describes the XGT Panel Menu.
Explanation
It describes the way to backup recipes, logging and other files by using
Chapter 6 Backup files by using
storage devices.
storage devices
It describes inspection categories and methods for long-term normal
Chapter 7 Maintenance
operation of the HMI system.
EMC Standard
Chapter 8 It describes the system configuration for EMC standards.
Certification
Appendix 1 Troubleshooting It describes a variety of error contents and measures.

Appendix 2 Dimensions It describes the dimensions of the XGT Panel.

Warranty and
Appendix 3 -
environment policy

Notes

This manual does not explain XP-Builder or PLC connections. Please refer to the related manual for these functions.

1-1
 Chapter 1 Overview

1.2 Features
The XGT Panel has the following features.

(1) Various types of external interfaces

(a) Supports various USB devices, Ethernet, and maximizes the customer’s usability.
(b) Connect devices such as PLC · Inverter communication in a variety of ways.
• RS-232C, RS-422/485 and Ethernet (10Base-T / 100Base-TX / 1000-Base-T) communication with the control device.

(2) Based on Windows CE

(a) Adopted Microsoft Company's WEC 7
• Windows Embedded Compact 7 has been used.
(b) Windows Embedded Compact 7 Features
• It provides stable software capacity by using Microsoft’s platform.
• It can process diverse functions simultaneously.
• It provides diverse interfaces including Ethernet and USB.
• User interfaces including mouse and keyboard can be connected.
• It has high flexibility like computer software.
• Fast reactions are available when adding new equipment.
• Wide data sharing and management with upper systems is available.

(3) Projects can be sent in various ways

(a) Project transmission using RS-232C communication
(b) Project transmission using Ethernet port
(c) Project transfer using USB Loader cable
(d) Project transmission using USB memory

USB Memory

XP-Builder

USB Loader
Cable

RS-232C/Ethernet

(4) Providing a high-quality screen

(a) It adopts high-performance liquid crystal display (LCD) to provide high picture quality and sharpness.
• It adopts thin film transistor liquid crystal display (TFT LCD) which can display 24bit color.
Supports various graphic formats.
• Supports 1024 X 768 graphic formats precisely and with realistic representation.
• Supports behavior for animations (GIF).
(c) Supports external display output.
• HDMI output is supported.
• Duplicate mode and extended mode enable screen output in various configurations.

1-2
 Chapter 1 Overview

(5) Application of Projective CAP touch panel

(a) Touch sensitivity is improved by applying electrostatic touch panel.
(b) Multi-touch and gesture functions.
(c) Various types of touch setting functions can be used according to user's work environment.

(6) Provides multilingual support and various fonts

(a) Supports multi-language languages.
• It uses the method of transferring the window / user font used on the computer to XGT Panel.
• No separate multilingual language development is required.
• Multilingual language support is an advantage of Windows CE.

(b) Supports simultaneous display of 12 languages.

• Simultaneous display in 12 languages
• Even when the XGT Panel is in operation, you can switch to another language by using special switches.

(c) Various fonts are provided.

• Windows / user fonts can be used, so various expressions are possible.
• You can freely adjust font size and shape.

1-3
 Chapter 1 Overview

(7) Providing various convenience functions

(a) Various alarm functions are provided.

• The history alarm can be divided into several alarm groups and alarm lists. The desired alarm can be displayed on the
screen with the alarm explorer.
• The flow alarm displays the current alarm at the bottom of the screen.
• The system alarm is displayed when a critical problem occurs during operation.

(b) It provides a logging function.

• It provides periodic logging that works repeatedly according to the time and device status and conditional logging
according to device conditions.
• Backup provides up to 1 Mbyte.
• You can backup to a USB.
• Backup data is stored in Excel format, so you can use it conveniently.

(c) It provides a recipe function.

• It provides read / write function.
• One recipe provides up to 100 double words (DWORD), 16 blocks.
• You can backup to a USB.
• Backup data is stored in Excel format, so you can use it conveniently.

(d) It provides a scheduler function.

• Up to 32 schedulers can be set.

(e) It provides a printing function.

• Screen / alarm printing function.
• Print out the printout.

(f) It provides scripting capabilities.

• User-written scripts provide more flexibility.
• Global / Object / Screen display.

(8) Stable products conforming to international standards

(a) CE, KC (Electromagnetic compatibility registration) standard acquisition

1-4
 Chapter 1 Overview

1.3 Terminology

It describes terms used in this manual.

Term Definition Note

A standard element that has a specified function which configures the Ex) CPU module
Module system. Devices such as I/O board, which are inserted onto the mother Power Module
board or base unit. I/O module
System consisted of PLC and peripheral device which can be controlled by
PLC system -
user program.

XP-Builder Software used to write and edit the project. -

XP-Manager Software that can be configured to communicate between XGT Panel -

XP-Remote Software used to remote monitor and control the XGT Panel -

Cnet module Computer Link -

FEnet module Fast Ethernet Network -

Abbreviation of Real Time Clock, It is used to call general IC that contains the
RTC -
clock function.

AC voltage Voltages whose charge flow and direction change periodically with time

Electrical device with a connecting ground wire in to keep the electric

Ground
potential of the device to zero

Electric shock The current flows in the human body, causing injury or shock.

Failure to observe the instructions may cause dangerous situations that may
Caution Caution
result in serious injury or damage to property or property damage.
Failure to observe the instructions may cause dangerous situations that may
Warning Warning
result in death or serious injury.
As a general precaution, when you need to observe the instructions given in
Caution mark
the user's manual

1-5
 Chapter 1 Overview

1.4 Product Name Rule

It describes terms used in this product’s names.

iXP2 -
(A) (B)(C)(D) (E)

Menu Sign Contents Note

08 21cm (8.4”) -
10 26 cm (10.2”) -
(A) LCD size
12 31cm (12.1”) -
15 38 cm (15.0 ) -
0 WinCE 7.0 (Core) -
(B) O/S type
1 WinCE 7.0 (Pro)
395 × 294 × 485
(C) Communication Ethernet(10 Base-T/100
0 Standard type
support Base-TX, 10 Base-T/100
Base-TX/1000 Base-T)
A AC 100 ~ 240V -
(D) Power
D AC 19.2 ~ 28.8V -
EXP Export product -
(E) Extension code
Ex Explosion proof product -

1-6
 Chapter 2 System Configuration

Chapter 2 System Configuration

Characteristic of each iXP2 series and its system configuration are as follow;

2.1 Part Names

1. iXP2-08xxA/D, 10xxA/D, 12xxA/D, 15xxA/D

4
2

No. Name Function

1) Display the power status of the device
1 Power LED
※ Display using high brightness blue LED
1) USB Host 1ch
2 Front USB
2) USB Device 1ch
1) P-CAP touch panel: User touch input
3 Front Part
2) LCD: Display
4 Panel fixing portion 1) Fix ing XGT Panel to Panel with Bracket

2-1
 Chapter 2 System Configuration

iXP2-1200A

10

11

5 6 7 8 9

No. Name Function

5 PE connector PE connection

6 Power Connector Power and PE connections

7 Cable fixing hole Fixing Cables

8 RS-422/485 connector RS-422/485 (COM3): PLC / Control device communication

ON
A

1 2 3 4
<Setting switch>
Battery cover, RS-422/485 termination resistance On
A Side.
Reset switch, No. 1/2 (Default)
9
Backup battery,
B Side. RS-422/485 termination resistance Off
Setting switch
A Side. O/S Download
No. 3
B Side. Nand Flash booting(Default)
A Side. Backup Battery On
No. 4
B Side. Backup Battery Off(Default)
<Reset S/W>
System reset switch. Pressing the switch will reset the system.
10 SD Card Logging / Recipe / Alarm / Project data backup and transfer

11 Gasket Protecting from water and dust

2-2
 Chapter 2 System Configuration

12 13 14 15 16 17 18

No. Name Function

12 Audio-Out Stereo audio output

13 HDMI Clone mode display output

1) USB memory connection: Logging / Recipe / Alarm / Project data
Backup and transfer
14 USB host
2) User Interface Connection: Use mouse / Keyboard
3) Printer connection: Print function
Ethernet: 10Base-T / 100Base-TX
1) Project data transmission
15 Ethernet terminal 2) Logging / Recipe / Alarm / Screen Data Backup
3) Upgrading the device software
4) PLC / control device communication
Ethernet: 10Base-T / 100Base-TX / 1000Base-T
1) Project data transmission
16 Ethernet terminal 2) Logging / Recipe / Alarm / Screen Data Backup
3) Upgrading the device software
4) PLC / control device communication
17 RS-232C connector RS-232C (COM2): PLC / Control device communication
Thanks to anti-drop lock, the Panel can be installed in a panel by a single
18 Anti-drop lock
operator.

Note
(1) The surface of the touch panel must be kept clean at all times.
- Foreign objects (water, oil, etc.) on the touch panel may cause malfunction.
(2) Touching the front of the touch panel may cause malfunction.
- Be careful that conductive objects do not touch the touch panel.
(3) The switch No. 1/2 of the setting switch must be set in the same direction.
- If switches 1 and 2 are set in different directions, communication problems may occur.
(4) Refer to the communication manual for details on communication connection.
(5) Please refer to Chapter 10 for installation details.
(6) For explosion-proof products
- Can open front USB cover using star wrench
- Front USB can only be used as a maintenance function

2-3
 Chapter 2 System Configuration

2.2 System Configuration

To use XGT Panel, you must create project data in XP-Builder and transfer it to XGT Panel.

By default, you can connect to XGT Panel using USB.

Basically, it can be connected with XGT Panel using RS-232C method.

The maximum communication speed is 115,200 [bps].

With Ethernet, project data can be transferred quickly.

If the LAN environment is established as shown below, you can use it more easily and effectively.

1: 1 connection is also supported in case LAN (LAN) environment is not established.

USB Memory

XP-Builder

USB Loader
Cable

RS-232C/Ethernet

If project data can not be transferred using communication, you can transfer data using USB storage device or SD card.
Please refer to Chapter 5 and XP-Builder User's Guide for more information.

USB Memory

SD
Card

Note
(1) It is recommended to use Ethernet rather than RS-232C.
(2) Refer to the communication manual for how to make the Ethernet cable.
(3) Refer to XP-Builder manual for project transfer method.

2-4
 Chapter 3 Standard Specification

Chapter 3 Standard Specification

3.1 General Standards

General specifications of XGT Panel are as follows.
Related
No. Item standard
Standards
Ambient
1 0 ° C ~ + 50 ° C -
temperature
2 Storage temperature -20 ° C ~ + 60 ° C -

3 Operating humidity 10∼85%RH, non-condensing. -

4 Storage humidity 10∼85%RH, non-condensing. -

Occasional vibration Count -

frequency acceleration amplitude

5≤f<9 Hz - 3.5mm

9≤f≤150 Hz 9.8m/s2 -
Vibration
5 10 times each
resistance
Continuous vibration in X, Y and Z IEC 61131-2
direction
frequency acceleration amplitude

5≤f< 9 Hz - 1.75mm

9≤f≤150 Hz 4.9m/s2 -
* Maximum shock acceleration: 147m/s2 (15G)
6 Shock endurance * Duration time: 11ms IEC 61131-2
* Pulse wave: half sine pulse (3 times each in X, Y and Z directions)
Square wave AC: ± 1,500V LS
Impulse noise DC: ± 1,000V ELECTRIC
Electrostatic
IEC 61131-2
Discharge ± 4 kV (contact discharge), ± 8 kV (air discharge)
IEC 61000-4-2
Immunity
Electromagnetic
IEC 61131-2
Radiated 80 ~ 1,000 MHz, 10 V / m
IEC 61000-4-3
Noise Emissions
7
Immunity
Fast Category Power module Communication interface
IEC 61131-2
Transient
IEC 61000-4-4
/ Burst noise Voltage 2 kV 1 kV
Communication
Category AC power DC power supply
interface
Surge IEC 61131-2
2kV (LG) 1kV (LG)
Voltage 1 kV
1 kV (LL) 0.5 kV (LL)
8 Environment Free from corrosive gases and excessive dust -

9 Operating height Below 2,000m (6,562ft) -

10 Pollution degree 2 or less -

11 Cooling method Natural Air-Cooling -

3-1
 Chapter 3 Standard Specification

Note

(1) IEC(International Electro technical Commission)

- International private group facilitating international cooperation of electric/electronic standardization, issuing
international standards and operating the compliance evaluation systems.
(2) Pollution degree
- As an index representing the pollution degree of an environment to determine the insulation of a device,
pollution degree 2 generally means the status generating non-conductive contamination. However, it also
contains the status generating temporarily conduction due to condensation.
(3) Noise Immunity
- The noise standard is the standard of the HMI body and the operation of the video display device connected to HDMI is not
guaranteed.

3-2
 Chapter 3 Standard Specification

3.2 Function Standards

The functional specifications of XGT Panel are as follows.

(1) Normal Type

Item iXP2-08xxA/D iXP2-10xxA/D iXP2-12xxA/D iXP2-15xxA/D

Display type TFT color LCD
Screen size 8.4 " 10.4 " 12.1 " 15 "
Display resolution 800 x 600 1024 x 768
Color indication 24-bit color (16.7M colors)
Right and left: 80 deg. Right: 75 deg. Right and left: 80 deg.
Indication degree Top: 80 deg. Top: 75 deg. Top: 80 deg.
Bottom: 60 deg. Bottom: 75 deg. Bottom: 80 deg.
Backlight LED method, automatic On / Off support
Backlight lifetime 50,000 hour
Touch panel Capacitive Touch
Audio otput Magnetic Buzzer (85dB)
Processor 1GHz, Dual core
Drawing Memory 128Mbyte
Memory Operating RAM 1GB
Backup RAM 1 Mbyte
Backup data Date / Time data, Logging / Alarm / Recipe data, Non-volatile devices
Battery CR2032(3.0V/210mAh, About 3years/25℃)
Video Output 1 x HDMI
Audio Out 3.5Ф x 1, 40mW
Ethernet 1 x 10Base-T / 100Base-TX, 1 x 10Base-T / 100Base-TX / 1000Base-T
USB host 3 x USB 2.0 (Front x 1, Rear x 2)
USB device 1 x USB 2.0 (Send / Receive front, PC and project data etc.)
RS-232C 1 x RS-232C (DSUB 9 / Male type)
RS-422/485 1 x RS-422/485 (Terminal Block)
Multi-language Can display 12 languages simultaneously
Animation GIF format support
Recipe Support
Data logging Support
Script Launcher Support
Standard Certification CE, KC, UL
Protection standard IP66(Front)
Dimensions (mm) 240 × 180 × 60 271 x 212 x 60 313 × 239 × 60 395 × 294 × 66
Panel Cut (mm) 228.5 x 158.5 259.0 x 201.0 301.5 x 227.5 383.5 x 282.5
Power A(AC100~240V), D(DC19.2~28.8V)
Power consumption (W) 25 25 30 30
Weight (Kg) 1.87 2.35 3.0 4.6

3-3
 Chapter 3 Standard Specification

(2) Special Type

Item iXP2-08xxA/D-EX iXP2-10xxA/D-EX iXP2-12xxA/D-EX iXP2-15xxA/D-EX

Display type TFT color LCD
Screen size 8.4 " 10.4 " 12.1 " 15 "
Display resolution 800 x 600 1024 x 768
Color indication 24-bit color (16.7M colors)
Right and left: 80 deg. Right: 75 deg. Right and left: 80 deg.
Indication degree Top: 80 deg. Top: 75 deg. Top: 80 deg.
Bottom: 60 deg. Bottom: 75 deg. Bottom: 80 deg.
Backlight LED method, automatic On / Off support
Backlight lifetime 50,000 hour
Touch panel Capacitive Touch
Audio otput Magnetic Buzzer (85dB)
Processor 1GHz, Dual core
Flash 1GB
Memory Operating RAM 1GB
Backup RAM 1 Mbyte
Backup data Date / Time data, Logging / Alarm / Recipe data, Non-volatile devices
Battery CR2032(3.0V/210mAh, About 3years/25℃)
Video Output 1 x HDMI
Audio Out 3.5Ф x 1, 40mW
Ethernet 1 x 10Base-T / 100Base-TX, 1 x 10Base-T / 100Base-TX / 1000Base-T
USB host 3 x USB 2.0 (Front x 1, Rear x 2)
USB device 1 x USB 2.0 (Send / Receive front, PC and project data etc.)
RS-232C 1 x RS-232C (DSUB 9 / Male type)
RS-422/485 1 x RS-422/485 (Terminal Block)
Multi-language Can display 12 languages simultaneously
Animation GIF format support
Recipe Support
Data logging Support
Script Launcher Support
Standard Certification CE, KC, UL, IECEx, ATEX, KCs
Protection standard Ex nA IIC T5 Gc, Ex tc IIIC T100℃ Dc IP64
Dimensions (mm) 240 × 180 × 60 271 x 212 x 60 313 × 239 × 60 395 × 294 × 66
Panel Cut (mm) 228.5 x 158.5 259.0 x 201.0 301.5 x 227.5 383.5 x 282.5
Power A(AC100~240V), D(DC19.2~28.8V)
Power consumption (W) 25 25 30 30
Weight (Kg) 1.87 2.35 3.0 4.6
1. The equipment presents a potential electrostatic hazard. Clean only with a damp cloth.
2. The device for nA marked equipment shall be installed in an enclosure that maintains and ingress protection rating of at least IP4X
where there are bare live parts and the equipment is intended for installation only in locations proving adequate protection against the
Specific conditions
entry of solid foreign objects or water capable of impairing safety.
of use
The device for tc marked equipment shall be installed in an enclosure IP64 in accordance with IEC 60079-31.
3. Must be installed in accordance with EN 60079-14.
4. Do not connect or separate plugs and sockets while an explosive atmosphere is present.

3-4
 Chapter 3 Standard Specification

Item iXP2-08xxA/D-EX iXP2-10xxA/D-EX iXP2-12xxA/D-EX iXP2-15xxA/D-EX

5. Keep out of direct sunlight

Note
(1) Caution in power connection
- With AC power applied to DC power device, it may cause product damage or fire. Please pay a special
attention to connection.
(2) PE Connection
- For the device PE, please use PE terminal.
(3) Battery discharge-prevention DIP switch
- In order to prevent the battery discharge, turn off the DIP switch No.4.
To use backup function, please turn on DIP switch No. 4.
(4) Battery Operation and Life
- Battery is used for RTC (date/time) when the power of device is off. Battery is not consumed with power
applied.
(5) LCD Backlight Replacement
- Please replace LCD if you want to replace LCD backlight.
(6) Protection standard
- XGT Panel is designed by IP66 Standard in front parts. Ingress Protection (IP) is based on the IEC 60529
Standard for degrees of protection provided by enclosures. But XGT Panel does not guarantee from all
installation environment. When installing panels, make sure that dust and moisture are not brought in. For
more details on installation, See Chapter 4.Installation and Wiring.
- It complies with the following specifications.
IEC 60079-0:2011
EN 60079-0:2011
IEC 60079-15:2010
EN 60079-15:2010
IEC 60079-31:2013
EN 60079-31:2013

3-5
 Chapter 3 Standard Specification

3.3 Cable Standards

3.3.1 UTP Cable

UTP cables are categorized into two types with the following standards..
① Shield type: Three types (UTP, FTP, STP)
② Seven types of frequency bands used 7 types (Cat.1-7)

(1) Cable types (shields)

Type Details Purpose

Max 200 MHz
UTP(or U.UTP) Unshielded cable for fast signals
Audio + Data + Low video signals
Max 100 MHz
FTP(or S.UTP) Cable shielding cable cores only Considers EMI and electric stabilization
Audio + Data + Low video signals
Max 500 MHz
Double layer shielding by shielding
Audio + Data +
STP(or S.STP) each pair and
Video signals
cable shielding cable cores only
For replacing 75Ω coaxial cables

UTP FTP STP

Note
(1) UTP: Unshielded Twisted Paired Copper Cable
FTP: (Overall) Foiled Twisted Paired Copper Cable
STP: (Overall) Shielded (and Shielded Individually Pair) Twisted Paired Copper Cable

(2) Patch Cable (or Patch Cord)

For the purpose of improving the flexibility of the UTP 4-pair cables, sometimes a wired conductor is used instead
of a solid conductor.
The target standards and materials used are Un-coated AWG 24 (7/0203A).
In other words, the small line diameter is 0.203 mm, the small line is standardized to 1 + 6 structure, and the
material is the annealing copper wire.

(3) For the PLC Ethernet communication cable use of the S.STP cable is recommended. If the S.STP cable
cannot be used due to the environmental conditions, it may result in communication abnormalities and noise in more
than one module.

(2) Type per used frequency

3-6
 Chapter 3 Standard Specification

Transmission
Type Used frequency (MHz) Purpose
speed (Mbps)
Category 1 Audio frequency 1 Telephone network (2Pair)

Category 2 4 4 Multi pair communications cable

Category 3 16 16 Telephone network + Computer network

Speed up the computer network
Category 4 20 20 2) Low-loss communications cable
Category 5 and 1) Digital telephone network + Computer
Enhanced 100 100 network
Category 5 2) Low-loss, broadband cable

Note

(1) The categories that are commercially available in Korea and globally are categories 3, 5, En-Cat.5 and CAD.6.
Category 4 is now defunct following the category 5 appearances, and category 7 is a STP structure that is in the
development phase worldwide

(3) Example of category 5, UTP (CTP-LAN5)

Item Unit Value

Conductor resistance
Ω/km 93.5
(Max)
Insulation resistance
MΩ·km 2,500
(Min)
or less voltage V/Min AC 500
Characteristic
Ω (1-100MHz) 100 ± 15
impedance
10 MHz Attenuation
dB/100 m
Attenuation 16 MHz
or less
20 MHz
10 MHz Near-end crosstalk attenuation
Near-end crosstalk dB/100 m
16 MHz
attenuation or less
20 MHz

3-7
 Chapter 4. Installation and Wiring

Chapter 4 Installation and Wiring

4.1 Installation

4.1.1 Installation environment

This machine has high reliability regardless environment. But for reliability and stability, be careful the followings

(1) Environment condition

(a) Install at the panel which can protect this machine from water and dust. XGT Panel is designed by IP66
Standard in front parts and IP20 Standard in rear parts.
(b) Install at the place where impact and vibration is not continuously applied. XGT Panel is designed to
meet IEC standard (IEC 61131-2).
(c) Do not expose this machine to direct light.
(d) Do not install at the place where rapid temperature change can occur. Moisture by rapid temperature
change can cause malfunction and damage.
(e) If the XGT Panel is exposed to low or severe temperature changes, dew may may occur between
the front panel and LCD screen. In this case, malfunction or damage of the product may occur, so wait until
the surface temperature of the XGT Panel is close to the ambient temperature before turning on the power.
(f) This machine should be installed within 0~50°C, otherwise the screen may be changed or cause
malfunction.
(g) This machine should be installed within 10~85% relative-humidity. Moisture by rapid temperature change
can cause malfunction and damage.
(h) Avoid corrosive gas and burnable gas.

(2) Installation construction

(a) When doing screw’s processing or wiring construction, be careful that the remains do not enter the XGT
Panel inside.
(b) Install at the place where you can easily control.
(c) Do not install with high voltage machine within same Panel.
(d) Keep distance of more than 100mm from duct for wiring and peripheral machine.
(e) Ground at the place where few noises develop.

(3) Anti-heat design of control panel

(a) In case of installing XGT Panel in the airtight panel, consider the heat by other machine as well as own
heat. In case that the air circulates through a ventilating opening or a general pan, XGT Panel system can
be influenced by in-draft of dust or gas.
(b) We recommend you to install a filter or to use an airtight heat exchanger.

4-1
 Chapter 4. Installation and Wiring

Note
(1) Waterproof and dustproof standard
(a) IP66 Standards
1) The protection standards of XGT Panel have been designed to meet the IP66 test conditions,
in accordance with the degrees of protection provided by enclosures of IEC60529.
As this machine installed at the panel, it is not guaranteed with all installation environment even
though its protection standards for the front parts are satisfied.
2) IP66 rating guarantees the enclosure is dust proof (6) and protected against jets of water (6).
3) IP20 rating guarantees protection from solid foreign objects of above 12mm diameter proof (2),
but it does not guarantee protection from water ingress.

(KS C IEC 60529: 2006 standard)

(b) Notice
1) In the environment where the protection grade of XGT Panel is exceeded or not satisfied,
the damage of the device or malfunction can occur due to the failure of protecting the product.
2) Since the protection grade of XGT Panel is the water-proof/dust-proof standards, it cannot be
protected from oil, corrosive gas and metal particles.
3) In case when Gasket is damaged by chemicals and continuous vibration, its water-proof/dust-proof
effect can be weakened.
4) In case when installing the panel, make sure that dust and water are not brought in panels.

4-2
 Chapter 4. Installation and Wiring

4.1.2 Notice in handling

This section describes the precautions for handling the XGT Panel from opening to installation.

 Do not drop or subject it to strong impacts.

 Do not open the product case or take any action. In such cases, we are not responsible for the product.
 When wiring, be careful not to let foreign substances such as wiring residue into the XGT Panel.

4.1.3 Precautions for panel installation

Describes how to install the XGT Panel on the panel and notes.

(1) Panel cut

 Before installing the XGT Panel on the panel, it must be manufactured on the panel as shown in the table below.
Unit: [mm]

division X (Horizontal) Y (Vertical) Z (Thickness)

+1 +1
iXP2-08xxA/D 228.5 158.5
-0 -0
+1 +1
iXP2-10xxA/D 259.0 201.0
-0 -0
1.6 to 6.0
+1 +1
iXP2-12xxA/D 301.5 227.5
-0 -0
+1 +1
iXP2-15xxA/D 383.5 282.5
-0 -0

X
100 Z

100

100

4-3
 Chapter 4. Installation and Wiring

(2) Panel installation

 When mounting the XGT Panel on the panel, please install 100mm or more in each direction.

Unit: [mm]

100

100
100 100

100

Note
(1) In order to be less affected by electromagnetic waves (radiation noise) or heat generated by other control devices,
Required.
(2) Install it considering the wiring of power and communication cables.
(3) When the panel cut dimensions are outside the reference tolerance (0 ~ + 1mm) when making the panel, the gap
between the gasket and the panel. The contact area may be reduced, and the waterproof and dustproof effect may be
weakened.
(4) When mounting the product on the panel, use gasket for waterproof and dustproof. The XGT Panel basically has a
waterproof and dustproof gasket is equipped.
(5) If the surface of the panel on which the XGT Panel is mounted is uneven, there is a gap between the XGT Panel and the
panel, or dust may penetrate. Particularly, depending on the material (steel, aluminum, acrylic, etc.) of the panel, This may
require installation environment review. Also check that the gasket and panel are in close contact. It is absolutely
necessary.
(6) If the condition of the gasket is contaminated or damaged due to deterioration at the time of installation or after a certain
period of use, the waterproof and dustproof effect care should be taken because it can be significantly weakened, and if a
gasket needs to be replaced, contact your nearest dealer or service. Please contact the center.
(7) In case of explosion-proof equipment, it should be installed in the environment with pollution degree 2 or less according to
KS IEC 60664-1.
(8) Install the front of the explosion-proof product in a place protected from the inflow of liquid in order to maintain the
explosion-proof performance after installation in accordance with the requirements of the obligatory safety certificate notice
of the protection device (Ministry of Employment and Labor Notice 2013-54)

 When installing the product on the panel, use gasket for waterproof and dustproof. The XGT Panel is basically equipped with
a waterproof and dustproof gasket.

(3) Installation location

 Please consider screen display and touch use for XGT Panel installation.
 If you exceed the display angle below, the screen may not be clearly visible. It is recommended to install the product considering
the angle of view.

4-4
 Chapter 4. Installation and Wiring

Division Angle (left and right) Upper Lower

iXP2-08xxA/D 80 deg. 80 deg. 60 deg.
iXP2-10xxA/D 75 deg. 75 deg. 75 deg.
iXP2-12xxA/D 80 deg. 80 deg. 80 deg.
iXP2-15xxA/D 80 deg. 80 deg. 80 deg.

(4) Fixing
 Fix the XGT Panel using the brackets on the panels as shown below.
(The bracket is included in the product.)

Fixed Bracket
Panel

Note
(1) During installation, XGT Panel should be closely contacted to the panel not to have any gap. In the
environment requiring water-proof/dust-proof effect, install and fix a bracket on a slope.
(2) The bracket should be fixed symmetrically(Up-Down, Left-Right). In case when it is not fixed
symmetrically, there could be a gap between the panel and XGT Panel.
(3) When fixing the bracket, it should be installed perpendicularly to the panel, and the required bracket
screw torque is 6.7kgf ㆍ cm. Depending on the material type of the panel, the torque value can be
different. The standard screw torque for each bolt size is followed. If it is fixed with the power more than
the required screw torque, the touch malfunction or weakening of water-proof/dust-proof can happen due
to the deformation of XGT Panel.

(5) Removal of protective film

4-5
 Chapter 4. Installation and Wiring

 Be sure to remove the film attached to the panel to protect the front sheet when it is shipped from the factory.

Note
(1) Remove the protection film attached to the front of this machine. Due to the deformation of the
protection film, the touch malfunction or wrong input can occur. It is recommended to use a special
protection sheet to protect the front sheet. In case of purchasing the protection sheet, contact the
agency or a sales office close by.

(6) Product Separation

 Loosen the fixing bracket screw and remove the bracket from the XGT Panel.
 Press the Anti-drop lock as shown below and then slowly push it forward to remove it from the panel.

Back of product Panel

Note
(1) If the device is forcibly remove from the panel without anti-drop lock, the product may be damaged.
(2) Be careful not to drop the product when removing the device from the panel.

4-6
 Chapter 4. Installation and Wiring

4.2 Wiring

Describes the wiring matters when installing the XGT Panel.

4.2.1 Power Wiring

XGT Panel is divided into DC (DC) and AC (AC) products.

power Product Name

iXP2-08xxD
iXP2-10xxD
DC 24V
iXP2-12xxD
iXP2-15xxD
iXP2-08xxA
iXP2-10xxA
AC100-240V
iXP2-12xxA
iXP2-15xxA

Caution
► Connecting AC power to a device that uses DC power may cause product damage or fire.
Be careful of connection.
► 'XXD' is a product using DC 24V and 'XXA' is a product using AC100-240.
Be sure to check the polarity of the back of the product before use.
► The equipment shall be installed in an enclosure which maintains an ingress protection rating protection
rating of at least IP64 and meets the enclosure requirements of IEC 60079-0 and IEC 60079-15, IEC
60079-31.
► Transient protection shall be provided that is set at a level not exceeding 140 % of the peak rated voltage
value at the supply terminals to the equipment.
► The equipment shall only be used in an area of not more than pollution degree 2, as defined in
IEC 60664-1.
► Plugs and sockets shall not be separated while an explosive atmosphere may be present.
► The equipment presents a potential electrostatic hazard. Clean only with a damp cloth.
► Install in a vertical direction only.

4-7
 Chapter 4. Installation and Wiring

Use the following specifications for the power cable.

Type Cable specification (Unit: ㎟) Wire Type Thermal Resistance Screw Torque

Power and protection

1.5(AWG16) ~ 2.5(AWG12) Copper 60℃ 0.51N•m
ground

Note
(1) For installations where there is voltage drop, it is recommended to use stranded wire with a cross
sectional area greater than 2 ㎟.
(2) It is recommended that cable connections are twisted and secure. Short cable runs are also
recommended between the point of supply and the XGT panel.
(3) For safety reasons it is recommended that you use color coded outer sheaths on the conductors to
aid safe terminations.

Power connection is as shown below.

L N PE + - PE

Power
Supply
a a
b b

[AC connection] [DC connection]

Note
(1) When the power fluctuation is larger than the specified value range, use a constant voltage transformer.
(2) When there is a lot of noise in the power supply, use an insulation transformer.
(3) Momentary power failure for stable data backup when power on / off. Please use.
(4) “a” is external earth, “b” is internal earth.

4-8
 Chapter 4. Installation and Wiring

For XGT Panel power supply, I / O devices and power devices, separate the power supply system as shown below.

HMI
Main Noise
power
Power Filter
PE

Others

Note
Do not bring the power line of the XGT Panel close to the main circuit (high voltage, high current) line or I / O signal
line. Possible 100mm Install at an interval of more than two.

Use the surge absorber as shown in the figure below to prevent surge such as lightning.

XGT Panel

E1
E2

Surge absorber for preventing lightning

Note
(1) Separate grounding (E2) of the XGT Panel of ground surge absorber (E1).
(2) Select the surge absorber so that the surge absorber does not exceed the maximum allowable voltage even when
the power supply voltage rises to a maximum please give it to me.

4-9
 Chapter 4. Installation and Wiring

When there is concern about noise penetration, use an insulation shield transformer or a noise filter.
Be sure to twist the wiring of the input power supply as short as possible and do not let the wiring of the shielding transformer or
noise filter pass through the duct.
When using a magnetic contactor (MC) for AC / DC, it is recommended to use Ferrite Core at the power input terminal.

EX) Apply a ferrite core to the power terminal as shown in the figure.

L N PE
Ferrite Core
(CU1130B, E-TECH)
(CU1330G, E-TECH)
(ZCAT3035-1330, TDK)

4.2.2 Ground Wiring

(1) This XGT Panel has enough noise countermeasures, so it can be used without grounding except when there is a lot of noise.
However, when grounding, please refer to the following.

(2) Grounding should be done by dedicated grounding as much as possible.

Grounding works are classified as class 3 grounding (grounding resistance 100  Or less).

(3) When dedicated grounding is not possible, use common ground as shown in Fig.

XGT Panel Other XGT Panel Other XGT Panel Other

Panel devices Panel devices Panel devices

Type-3 ground Type-3 ground

A) Exclusive ground: Best B) Common ground: Good C) Common ground: Bad

(4) Ground wire is 2 mm2 or more. If possible, place the grounding point near the XGT Panel to shorten the length of the ground
wire.

Note
If the grounding condition is bad or connected as in (C), the XGT Panel may malfunction or communication failure
may occur. Be sure to check grounding.

4-10
 Chapter 4. Installation and Wiring

4.2.3 An external interface cable fixing

(1) Connect the cable tie through the external interface cable fixing hole on the back of the unit.

(2) Tighten the cable tie firmly so that the external interface cable does not come off by external force.

iXP2 -15XX, 12XX, 10XX Series iXP2 - 08XX Series

Caution
► External interface cable anchors are an important factor in maintaining explosion proof performance.
If it is not installed as described above, it may cause explosion due to spark due to abnormal connection of
cable. Therefore, please be sure to familiarize yourself with the above instructions.

4-11
 Chapter 5 XGT Panel Menu Explanation

Chapter 5 XGT Panel Menu Explanation

This chapter describes how to set the environment such as XGT Panel time setting, Ethernet connection setting, backlight setting.
If you press the [Settings] button on the XGT Panel main screen, you can set the environment of XGT Panel.

WinCE O/S V1.0 XP-Runtime V2.10 B[010]

[XGT Panel Basic]

After booting the XGT Panel after turning on the power, the XP-Runtime main screen is displayed. Functions of each menu are as
follows.
Menu Meaning Details Note
Backlight Setting
Touch Setting
DateTime Setting
Environment Setting
Configuration menu of
Settings Ethernet Setting Refer to 5.1 Settings
XGT Panel
Buzzer Setting
Sound Setting
XP-Remote Setting
Goto MainMenu
Screen
Touch
Backup Memory/
Flash Memory
Diagnostics function of
Diagnostics USB Memory Refer to 5.2 Diagnostics
XGT Panel
Serial
SD Card
Touch Sensitivity
Goto MainMenu

5-1
 Chapter 5 XGT Panel Menu Explanation

구분 의미 세부 항목 비고
Settings
PLC setting menu SHOW INFO
Refer to
PLC Information connected with Program Monitor
5.3 PLC Information
XGT Paenl OK
N:1 Settings
Refer to
Update XGT Panel For updating XGT Panel XGT Panel Update
5.4 Update XGT Panel
Project Download
It is for using Project Upload
Refer to
Storage Function the storage devices XGT Panel Update
5.5 Storage Function
used in XGT Panel Select USB
Cancel

5-2
 Chapter 5 XGT Panel Menu Explanation

5.1 Settings

WinCE O/S V1.0 XP-Runtime V2.10 B[010]

5.1.1 Backlight Setting

Press the [Backlight Settings] button on the [System Configuration] screen to go to the setup screen as follows.

[XGT Panel Setting]

5-3
 Chapter 5 XGT Panel Menu Explanation

[Backlight setting]

[Explanation of the dialog box]

Menu Explanation
Brightness Backlight Brightness can be adjusted.
Do not turn off backlight Backlight power is always on.
If you do not touch for a certain period of time, the backlight automatically turns
Turn off backlight after idle time
off.
Turn off after The backlight turns off after the set time (in minutes).

5-4
 Chapter 5 XGT Panel Menu Explanation

5.1.2 Touch Setting

You can adjust the sensitivity of the touch according to the type of gloves according to the work environment during touch operation. If
you press [Touch Setting] on the System Configuration screen as shown below, the setting window will be activated and you can set
the sensitivity according to the type of glove. You can set the sensitivity of the touch by user setting.

[XGT Panel Setting]

If you select the [PreDefined] option, the optimal sensitivity is set immediately when using bare hands, cotton gloves, rubber coated
cotton gloves, or water proof. If you want to adjust the sensitivity in detail, you can select [User Custom] option. In this case, you can
adjust the sensitivity in eight steps

[Touch setting]

5-5
 Chapter 5 XGT Panel Menu Explanation

In [Gesture Function], you can select whether or not to use the function using the finger gesture. If checked, PAN and Flick operation
enables screen changing and data list search (history alarm view, logging viewer, file explorer, etc).

Note
(1) By default, XGT Panel has touch setting. If the touch position error is large, Please contact us for action.
(2) If touch glass breakage occurs, it may cause touch operation problem.
(3) Touch glass may cause touch malfunction due to water droplets.
In this environment, please disable the gesture function

5-6
 Chapter 5 XGT Panel Menu Explanation

5.1.3 DateTime Setting

You can set the date and time of XGT Panel by pressing [DateTime Setting] button on [System Configuration] screen as follows.

[XGT Panel Setting]

2017

Today: 4/23/2017
[Date / Time Setting]

Note
Date / time view and setting are also available in the device information view of the communication setting dialog of XP-Builder.
For more information,See the XP-Builder User's Guide .

5-7
 Chapter 5 XGT Panel Menu Explanation

5.1.4 Environment Setting

If you press the [Environment Setting] button on the [System Configuration] screen to go to the setup screen as follows.

[XGT Panel Setting]

(1) Screen

5-8
 Chapter 5 XGT Panel Menu Explanation

Menu Explanation
If you select [Show always], the title bar displays when a pop-up window is displayed on
the screen. You can select and move the title bar of the pop-up window. If you select [Hide
Window’s title bar : Show always] the title bar will not be displayed when a pop-up window is displayed on the
always screen, and you will not see it when you click the window screen blank.
/Hide always If you uncheck [Show always], [Hide always], the title bar will not be displayed when the
pop-up window is displayed on the screen, and the title bar will appear when you click the
window screen blank.
Smoothly handle the edge of each stroke when the letter is displayed. To do this, you can
choose between Anti-aliasing and ClearType. Generally, applying ClearType is more
Smooth edges of fonts : poetic, but Anti-aliasing may be better, depending on the font type and font size. Smooth
Anti-aliasing/ ClearType font display by selecting one of the two increases the load on the system, especially as the
font size increases, it may have a performance impact on functions such as flow alarms.
This feature is available on iXP, iXP2 and later models
After rebooting XGT Panel or downloading edit data,
Goto screen
You will switch. If you disable this setting,
after boot up
Button to move to the screen.
When I start the screen, I do not cache the image in advance,
It does not appear. However, if you select this option, the initial screen may appear
Quick start somewhat late.
There is. In particular, if the screen contains animation objects,
It may take a few seconds. The next screen transition is fast.
If you choose [Drawing takes precedence], the screen that you have already entered
when switching the screen will display the image/value based on the data that was last
displayed at that time. Then read the actual device value and display the image/value
Drawing takes again. If the screen is entering for the first time, it will behave the same as when [Drawing
precedence takes precedence] is deselected.
If you deselect [Drawing takes precedence] when switching the screen, read the actual
device value and display the image/value. This may take some time to switch screens
depending on the network situation or PLC response rate.
In order to exit to the standby screen during screen monitoring,
Do not show menu bar The window (menu bar) does not appear. If this is the case,
You need to configure and use a special switch to exit the screen.
Enable Arabic text
Enables the right-to-left language.
Display (right-> left)
Set startup screen The screen corresponding to the number entered at the start of monitoring is displayed.

(2) General

5-9
 Chapter 5 XGT Panel Menu Explanation

Menu Explanation
Hide mouse cursor Mouse cursor does not appear after scrolling.
Buzzer On / Off You can set whether buzzer is used or not.
Buzzer test You can test the buzzer.
XGT Panel starts monitoring the images used on the screen to speed up the screen
operation.
It will be loaded into memory before use. By the way,
If a positive image is used, due to memory space constraints, all
The image will not load. In this case, if the screen is not yet loaded
Images are loaded, and there is not enough space, so unused images are retrieved from
Low Memory Mode
memory
The operation to delete may be repeated, and the screen switching operation may be
slowed down. In this situation
Low Memory Mode "is recommended. In Low Memory Mode, you do not load the image
before monitoring, but use only the original source of the image used in the project, which
results in less memory usage and less load to load and delete images into memory.
Ensures the order of operation when entering values by bit switch, word switch, multi-
switch, etc. when [Async mode] is deselected. In other words, when 1, 2, 3 actions are
performed by multiple switches or overlapped switches, 2 is performed when 1 action is
completed, and 3 is performed only when 2 is completed. Therefore, if there is no
response from the target controller in Operation 1, the actions 2 and 3 are also delayed
even if the controller is different.
Async mode
When [Async mode] is selected, the value is entered by bit switch, word switch, multi-
switch, etc. without ensuring order. In other words, when 1, 2, 3 actions are performed by
multiple switches or overlaid switches, each action can be completed in the order of 2, 1
and 3 depending on the network situation or controller response speed. Although the
order is not followed, it has the advantage of operating quickly for the rest of the controllers
even if some of them do not respond.

5-10
 Chapter 5 XGT Panel Menu Explanation

When XGT Panel starts, it turns off USB power  On to initialize the connected device.
Reset USB power
The initial setting is On, and if the USB recognition speed is slow or not well recognized
after boot up
Uncheck, power on again and try again.
When you start monitoring by selecting [Start] menu on the XGT Panel main screen,
It buffers the used image and shows the progress of the operation. (fast
Show progress Do not show progress if you make a start setting). At this time,
on the bottom If you check the [Show Lower] check box, this progress will be simplified and displayed at
the bottom of the screen.
Is displayed. This option can be applied when using the default screen image.
Sets whether the 5V power output is enabled at the 9pin D-sub terminal for RS-232C
RS-232C 5V
communication.
power supply
This feature is available on iXP, iXP2 and later models.
Delete all files you've downloaded on your device. However, connecting to the device
If a password is set, you must enter the password before you can delete it. The password
is the device connection password that you enter when downloading a project, This can
be set in XP-Builder on the Device Information View tab of the Communication dialog box.
Clear SRAM memory
The files to be deleted include user project data, web server, VNC startup module, option
And data files
card Driver, RAPIEnet communication setting data, XP-Manager setting data etc. from
user PC All downloaded data is included. Set using the configuration menu of the
machine. The contents are kept uninitialized. If the menu language is not English,
A device reboot is required to delete files.

5-11
 Chapter 5 XGT Panel Menu Explanation

(3) BK Image

Menu Explanation
If you select an image, the standby screen and desktop are selected after the XGT Panel
is powered on.

Set background image

If [Use boot image] option is selected, images with resolutions other than XGT Panel,
It can not be used unless it is a 24bit BMP image.
When you select an image, the XGT Panel is powered on and the standby screen and
desktop are selected.
Set to image. To turn off background settings, click the Clear Background button.
Delete background image
Just press it.
If you select the Use boot image option, you cannot use it unless it is an image with a
resolution different from the XGT Panel or a 24bit BMP image.

(4) Printer

5-12
 Chapter 5 XGT Panel Menu Explanation

5-13
 Chapter 5 XGT Panel Menu Explanation

Menu Explanation
Displays additional printer print settings dialogs. If there is no printer information
You should download from XP-Builder with the following message.
From XP-Runtime, go to Start menu and prepare for downloading.
After using the printer, you can use the menu.

<No printer driver and information  Download Required>

Printer Settings

<Printer Driver and Information Available>

5-14
 Chapter 5 XGT Panel Menu Explanation

Printer Settings
Menu Explanation
Port Connection method: Displays the connection method.
Printer type Printer type: Displays the printer type.
Print direction Orientation: Set whether it is horizontal or vertical.
Print color Print color: Set whether it is color or black and white.
High quality print Print quality: Set whether to print advanced.
View additional properties: Displays additional properties.
Printer Properties
More ... If you have made any changes, check whether you want to
save it,
Go to the dialog box.
OK Save the settings.
Cancel Cancels the setting.
Diagnose connectivity: Diagnoses the connection status of
the printer. this
The functions of the printer (LK-P30, LK-P41, LK-P43)
Support. Press the button to the right of the current status
Displays a message. If the printer is off
You can turn it on, connect the cable again,
Printer Check There is.

* Message Type *
One. OK: normal
2. No Printer: Not compatible with printer
3. Cover Open: Paper cover opened
4. Paper Empty: Out of paper
Test printing: To test the printout status
Function. It prints the following information and briefly
Outputs the printing status.

<Example of test page>

***********************************
Test page
Test Page ***********************************
DateTime: 2014-02-04 10:00:00
XP-Runtime version: 1320
Printer driver version: 1.00
Printer name: PCL3 LaserJet
Port: USB
***********************************

5-15
 Chapter 5 XGT Panel Menu Explanation

(5) HDMI

* Please refer to the

'Note' of ①and②.

<Clone mode> <Extension mode>

Menu Explanation
Not used HDMI function is disabled.
Clone mode The same screen is displayed on the monitor connected by HDMI.
Extended mode
Expands the screen to a monitor connected via HDMI.
(To be implemented)

Note

(1) ‘①’ is the same resolution as HMI.

Displayed as ‘iXP2 0800 :800 X 600, iXP2 10/12/1500 : 1024 X 768’.
(2) ‘②’ Extension mode 1280 X 720, 1920 X 1280 is a fixed resolution.

5-16
 Chapter 5 XGT Panel Menu Explanation

5.1.5 Ethernet Setting

If you press the [Ethernet Setting] button on the [System Configuration] screen as below, you can set the IP to use Ethernet.

You can change the IP by pressing the [Set] button for each item of IP address, Subnet Mask and Gateway.
If you click [OK] button, changed IP information will be saved. Two Ethernet ports [LAN 0] and [LAN 1] can be set respectively.

Note
For 1: 1 connection with PC, it is recommended to set as follows.

1) XGT Panel setting 2) PC setting

- IP address: 192.168.0.10 - IP address: 192.168.0.11
- Subnet Mask: 255.255.255.0 - Subnet Mask: 255.255.255.0
- Gateway: 192.168.0.1 - Gateway: 192.168.0.1

If you press the [Disable] button and reboot, the device will not use Ethernet. If this is the case,
You can get the effect. To use Ethernet again, press [Enable] button and reboot.

5-17
 Chapter 5 XGT Panel Menu Explanation

5.1.6 Buzzer Setting

You can adjust the volume and tone of Buzzer of XGT Panel.

[XGT Panel Setting]

[Buzzer setting]

[Explanation of the dialog box]

Menu Explanation
Buzzer On You can turn on or off the buzzer sound generated when the selection is made.
Buzzer volume You can adjust the volume of the buzzer.
Buzzer tone You can adjust the height of the buzzer.

5-18
 Chapter 5 XGT Panel Menu Explanation

5.1.7 Sound Setting

You can adjust the volume of XGT Panel.

[XGT Panel Setting]

[Sound setting]

5-19
 Chapter 5 XGT Panel Menu Explanation

5.1.8 XP-Remote Setting

You can change the settings for XP-Remote that can remotely control the XGT Panel.

[XGT Panel Setting]

[XP-Remote setting]
[Explanation of the dialog box]
Menu Explanation
Allow XP-Remote to connect Allow connection of remote XP-Remote.
Max. of XP-Remote Specify the maximum number of XP-Remote that can be connected to XGT Panel.
If there is no communication request from XP-Remote within the designated time,
communication is stopped,
Timeout value
If XP-Remote has operation authority, it recovers operation authority.
(10 seconds ~ 300 seconds)
Enable control by XP-Remote
After XGT Panel starts to monitor, operation permission status is automatically set.
after Monitor Start
Set Password You can set it to enter a password when you request a connection from XP-Remote.

Note
For details of XP-Remote, refer to the XP-Remote User's Manual.

5-20
 Chapter 5 XGT Panel Menu Explanation

5.2 Diagnostics

This chapter explains the functions that can be used to diagnose communication terminal, screen and touch function of XGT Panel.
If you click the [Diagnosis] button on the main screen of XGT Panel, a menu for diagnosing each function of XGT Panel is displayed.

WinCE O/S V1.0 XP-Runtime V2.10 B[010]

[XGT Panel Basic]

[XGT Panel Diagnostics]

5-21
 Chapter 5 XGT Panel Menu Explanation

5.2.1 Screen Diagnostic

When you press the [Screen] button, the screens with different colors are displayed in succession with the buzzer sound. After
all the screens for diagnosis are displayed, the graph will appear and the [Close] button will appear in the upper left corner.
When this [Close] button is pressed, Returns to the Diagnostics screen.

[XGT Panel Diagnostics]

[Screen Diagnostic]

Screen
Red  Green  Blue  Black  White  Graph
order

5-22
 Chapter 5 XGT Panel Menu Explanation

5.2.2 Touch Diagnostic

When you press the [Touch] button, the diagnostic screen appears. If you touch the screen, you can see that it is displayed like the
picture below. Press the [OK] button to exit the screen.

[XGT Panel Diagnostics]

[Touch Diagnostic]

5-23
 Chapter 5 XGT Panel Menu Explanation

5.2.3 Backup Memory Diagnostic

If you press the [Backup Memory] button, you can see the diagnostic results in the confirmation window.

[XGT Panel Diagnostics]

[Backup Memory Diagnostic]

Note
(1) If 'NVRAM Data Access ~~ Fail' occurs, take A/S action.
(2) If 'BATTERY STATUS ~~ BAD' occurs, you have to replace the battery through A/S.
If the rear setting switch 1 is set to B, set it to ON. B is a mode without backup battery.

5-24
 Chapter 5 XGT Panel Menu Explanation

5.2.4 Flash Memory Diagnostic

When you press the [Flash Memory] button, the diagnostic results appear in the confirmation window.

[XGT Panel Diagnostics]

[Flash Memory Diagnostic]

Note
1. If "Read Disk Information Error!" Occurs, please contact us.
2. Space allocation of Flash Disk may depending on O/S version.

5-25
 Chapter 5 XGT Panel Menu Explanation

5.2.5 USB Memory Diagnostic

When you press the [USB Memory] button, the diagnostic result appears in the confirmation window.

[XGT Panel Diagnostic]

[USB Memory Diagnostic]

Note
If USB memory is installed and 'Read Disk Information Error!' Occurs, remove it, insert it again and test
do it. If the error message occurs repeatedly, contact Customer Service.

5-26
 Chapter 5 XGT Panel Menu Explanation

5.2.6 Serial Diagnostic

Diagnostic function for serial communication port such as RS-232C, RS-422. Press the [Serial] button to diagnose the serial
ports installed on the XGT Panel. (However, for diagnosis, loop-back terminal must be connected to each port)

[XGT Panel Diagnostic]

[Serial port selection screen]

[Serial Diagnostic]

5-27
 Chapter 5 XGT Panel Menu Explanation

Please make RS-232C port terminal as below. (Connect pins 2 and 3.)

Connect the RS-422/485 port terminals as shown below.

(In case of RS-485 communication, connect pin 1, pin 3, pin 2 and pin 4)

Pin
name function
number
One TX + Data transmission
2 TX- Data transmission
3 RX + Receive data
4 RX- Receive data
5 SG Signal Ground
6 PE PE

5-28
 Chapter 5 XGT Panel Menu Explanation

5.2.7 SD Card Diagnostic

Displays information of SD card memory inserted in XGT Panel. Press the [SD Card] button to diagnose the SD memory mounted
on the XGT Panel

[XGT Panel Diagnostic]

[SD Card Diagnostic]

Note
If 'Read Disk Information Error!' Occurs when an SD card is installed, remove it, insert it again, and test it.
If the error message occurs repeatedly, take A / S action.

5-29
 Chapter 5 XGT Panel Menu Explanation

5.2.8 Touch Sensitivity

This function is visually displays the noise coming from the iXP2 series environment on the touch screen.

[XGT Panel Diagnostic]

[Touch Sensitivity Diagnostic]

5-30
 Chapter 5 XGT Panel Menu Explanation

Note
1. Touch Sensitivity is only able to check if noise is flowing into iXP2.
2. Touch Sensitivity is only supported in XP-Builder V3.00 or later.
3. When touch is input, the value around the input area is increased. If the value of the non-touch area changes drastically,
please take A/S action.

5-31
 Chapter 5 XGT Panel Menu Explanation

5.3 PLC Information

The PLC information view function is to view the connected XGT Panel information and CPU information and history of the
target PLC.

WinCE O/S V1.0 XP-Runtime V2.10 B[010]

[XGT Panel Basic Screen]

Note
PLC connection status can be viewed only when project data is transferred to XGT Panel.

5-32
 Chapter 5 XGT Panel Menu Explanation

5.3.1 PLC Communication Setting

[Settings] is a function to change communication parameters of PLC communicating with XGT Panel, and you can change
PLC communication setting items by clicking [Settings] button

[PLC information]

[PLC Communication Setting]

Note
- PLC communication setting screen may be different for each driver.
- Refer to individual PLC manual for PLC communication setting change contents.

5-33
 Chapter 5 XGT Panel Menu Explanation

5.3.2 Connection Information

You can check the connection number, PLC manufacturer, target PLC type, connection method, IP address, and timeout time set up
for connection with PLC in XP-Builder.

[PLC information]

[Explanation of the dialog box]

Item Explanation
Connection No. Displays the communication connection number. Available from 0 to 15.
Vendor Displays the manufacturer of the communication target device.
Target device Displays the communication target device.
Connection type Displays the connection method.(RS-232, RS-422, TCP/IP, ect.)
Timeout value Displays the set timeout time.
Send wait value Displays the transfer waiting time.
Displays the number of retransmissions when a timeout occurs during
Retry value
communication.

5-34
 Chapter 5 XGT Panel Menu Explanation

5.3.3 PLC Information

You can check the CPU type, operation mode, status, version and scan time of our own PLC model and provide information only
when connected with PLC.

Note
PLC types that can view PLC information are as follows.
- MASTER-K CPU, FEnet, Cnet
- GLOFA-GM CPU, FEnet, Cnet
- XGK / XGB / XGI / XGR CPU, FEnet, Cnet

5.3.4 History of PLC error

You can check the PLC error history of your own PLC model.

Note
The PLC types that can display the error history are as follows.
- The MASTER-K CPU has no error history.
- GLOFA-GM CPU, FEnet, Cnet
- XGK / XGB / XGI / XGR CPU, FEnet, Cnet

5-35
 Chapter 5 XGT Panel Menu Explanation

5.3.5 PLC Operation Mode Conversion History

You can check the PLC run / stop operation mode history of your PLC model.

Note
The following PLC types are available to view the PLC operation mode switching history.
- MASTER-K CPU does not have operation mode switching history.
- GLOFA-GM CPU, FEnet, Cnet
- XGK / XGB / XGI / XGR CPU, FEnet, Cnet

5.3.6 History of power off of PLC

You can check the PLC power shutdown history of your own PLC type.

Note
PLC type that can view the power off history is as follows.
- MASTER-K CPU has no power off history.
- GLOFA-GM CPU, FEnet, Cnet
- XGK / XGB / XGI / XGR CPU, FEnet, Cnet

5-36
 Chapter 5 XGT Panel Menu Explanation

5.3.7 PLC System History Information

PLC system history can be checked.

Note
The PLC types that can view the system history are as follows.
- The MASTER-K CPU has no system history.
- Only available with the GLOFA-GM CPU (GM4C). Other CPUs have no system history.
- XGK / XGB / XGI / XGR CPU, FEnet, Cnet

5-37
 Chapter 5 XGT Panel Menu Explanation

5.3.8 N: 1 Setting

XGT Panel supports N: 1 service which enables communication between several XGT Panels and one PLC. You can set details
using the [N: 1 Settings] menu.

[PLC information]

[N: 1 setting]

[Explanation of the dialog box]

Menu Explanation
Use N: 1 Communication N: 1 Specifies whether to perform communication.
N: 1 station number Enter the station number of N: 1 communication.
Number of XGT Panel N: 1 Enter the number of XGT panels on communication.
Master Holding Time Enter the master execution time of N: 1 communication.

Note
For detailed setting and understanding of N: 1 communication, refer to XP-Builder's N: 1 communication manual.

5-38
 Chapter 5 XGT Panel Menu Explanation

5.3.9 Program Monitor

XGT Panel can monitor ladder of PLC XGK of LS ELECTRIC.

[PLC information view screen]

Note
- Program monitor modules must be installed via XP-Manager.
- LS: XGK / XGB CPU, Cnet, and Enet driver.
- You must specify the use of the program monitor in the project properties of XP-Builder.

5-39
 Chapter 5 XGT Panel Menu Explanation

5.4 XGT Panel Update

The functions described in this chapter are for updating the XGT Panel software. By default, XGT Panel is also optimized
when downloading project file from XP-Builder. Use this function only if you need to update only the XGT Panel in particular.
The software of the XGT Panel will need to be updated with the new version as new functions and enhancements are
added. Refer to the following procedure.

[Method]
1. Connect XGT Panel and PC.
2. Run the XP-Builder.
3-1. Click [Communication] - [XGT Panel Update].
3-2. Click Connection Setup to select the type of XGT Panel and PC connected.
3-3. Click Browse and select the XP-Runtime file.

4. Select [XGT Panel Update] on the XGT Panel menu screen.

5. Click [Update] of the XGT Panel Update(No3-1).
When normal update is completed, return to XP Runtime menu screen.

WinCE O/S V1.0 XP-Runtime V2.10 B[010]

Note
1. Do not disconnect the communication cable or turn off the device while updating the XGT Panel.
XGT Panel may not update properly and may malfunction
2. Click Update XGT Panel menu and then click MENU on XP-Runtime screen to return to XP-Runtime menu
screen.

5-40
 Chapter 5 XGT Panel Menu Explanation

5.5 Storage Function

5.5.1 Overview
Download the project edited by the user in XP-Builder from PC or upload the project backed up in the device to PC
Uploading and updating the device are usually done by connecting USB cable or Ethernet cable to XGT Panel series.
You can do it through. In situations where this connection is not possible, you can use the storage device to proceed.
The function description for [Storage Function] is as follows.

WinCE O/S V1.0 XP-Runtime V2.10 B[010]

1. If you touch [Storage Function] on the menu, the following dialog box is displayed.

2. The contents of each menu are as follows.

Menu Description

Project Download To download a project from an external storage device to the XGT Panel
Project Upload To transfer project data backed up to an external storage device from XGT Panel
XGTPanel Update To update the XGT Panel Software from an external storage device

5-41
 Chapter 5 XGT Panel Menu Explanation

5.5.2 Downloading a project using a storage device

1. When you touch [Download Project] in the storage function menu, the following dialog box is displayed.

2. Project storage path of USB memory, SD card is displayed as below.

- \ USB Storage \ XP_Project \

- \ SD Storage \ XP_Project \

If you want to download a project using a storage device, it must be stored in the directory in the above path.

3. Select one of the directory listings.

4. Touch the [OK] button to start the download.

5.5.3 Uploading a project using a storage device

5-42
 Chapter 5 XGT Panel Menu Explanation

1. If you touch [Upload Project] in the storage function menu, the following dialog box is displayed.

2. The upload path of USB memory and SD card is displayed as below.

- \ USB Storage \ XP_Backup \

- \ SD Storage \ XP_Backup \

3. Touch the [OK] button to transfer the project backup file in the machine to the path of the selected storage device.

4. The project backup file must be downloaded to download the project backup file when downloading the project.
If not selected, the project backup file is not stored in the device and therefore can not be transferred to the storage device.

5.5.4 Updating the device using a storage device

1. If you touch [Update XGT Panel] in the storage function menu, the following dialog box will be displayed.

5-43
 Chapter 5 XGT Panel Menu Explanation

2. The path of USB memory, SD card is displayed as follows.

- \ USB Storage \ XP_Software \

- \ SD Storage \ XP_Software \

If you want to update the device using an external storage device, the XGT Panel Software file is in the directory in the
above path
It must be saved.

3. Touch the [OK] button to update the device with the XGT Panel Software stored in the specified path.

5-44
 Chapter 6 Backup files by using Storage Devices

Chapter 6 Backup files by using Storage Devices

This chapter describes the management functions for external storage devices that store backup data of logging, recipe, and
screen images.
(1) XGT Panel can back up logging, recipe, screen image data to USB storage device according to the settings set in XP-Builder.
(2) If there is no capacity to be backed up on the specified storage device, the existing data is deleted according to the settings
set by XP-Builder, and the backup process or backup is stopped.
(3) The XP-Builder monitors whether or not the external storage device specified as the backup device is detached.

6.1 Path Structure in case of File Backup

Backup path structure of logging, recipe, and screen image is as follows.

Root directory of SD or USB storage equipment.

Logging

1 (Logging Number)

YYYY.MM.BeginDay.EndDay.0

DD.BeginHour.EndHour.0 (space for one folder is full)

DD.BeginHour.EndHour.1 (There is free space for one folder)

DD.BeginHour. FF (There is free space for one folder)

HH.BeginMinute.FF

Lhhmmss0.CSV
2 (same as lower structure 1)

Recipe

Rhhmmss0.CSV (same as lower structure of each logging number)

ScreenImage

Shhmmss0.BMP (same as lower structure of each logging number)

6-1
 Chapter 6 Backup files by using Storage Devices

1. Path structure in case of logging backup

(1) Directory named ‘Logging’ is created under the root directory of USB equipment
(2) The directory whose name is logging number is created under Logging directory.
(3) The directory whose name is year, month is created under Logging number directory.
(a) Includes day directory under
(b) Up to 500 day directories can be created.
(c) Name of year, month directory includes the firstly created day information under its directory
Ex) In case directory is created in 2010, October and includes directory since 15th under, directory’s name is
: 2010.10.15.FF
FF at end means the directory can save more data created in 2010, October (currently, the number of lower
directory is 500 or less)
(d) In case month is changed, changes directory name to day information of last created day directory.
Ex) In case month becomes November from October and directory from 15th directory to 30th have been created
in 2010, October directory.
: 2010.10.15.30.0
(e) Though month is not changed, in case the number of day directory under year, month directory is 500 or above,
directory name is changed into name including day information of last created day directory.
Ex) In case the number of directory from first to 15th is 500 or above in the directory created in 2010, October.
: 2010.10.01.15.0
(f) In case there is the year, month directory having same start day and end day when changing directory’s name
due to over 500 day directories or change of month, last digit index number increases.
Ex) In case there are three year, month directories that are having over 500 day directories created in October
first and 2010 year October directory
: 2010.10.01.01.0
: 2010.10.01.01.1
: 2010.10.01.01.2
(4) Day directory is created under year, month directory
(a) Hour directory is created under day directory
(b) Day directory can have up to 500 hour directory
(c) Name of day directory includes not day information but also hour information of first created hour
directory
(d) Relation between day directory and hour directory is same as relation between year month directory and day
directory.
(5) Directory whose name includes hour information is created under day directory.
(a) Hour directory includes backup file under
(b) Hour directory can include up to 500 backup file
(c) Name of time directory include not only hour information but also minute information of first created file under
(d) Relation between hour directory and backup file is same as relation between year, month directory and day
directory.
(6) Name of logging backup file includes the created hour, minute, second information.
(a) Backup file is created in CSV format.
(b) File name start with ‘L’ meaning logging and includes hour, minute, second, index information
(c) In case backup file is created at the same time in terms of second, index information at the end of file name
increases.

6-2
 Chapter 6 Backup files by using Storage Devices

2. Path structure in case of recipe backup

(1) Directory named ‘Recipe’ is created under USB storage equipment root directory.
(2) Year, Month directory is created under Recipe directory
(3) The lower directory structure is same as that of logging backup path structure.
(4) Name of recipe backup file includes the created hour, minute, second information.
(a) Backup file is created in CSV format.
(b) File name start with ‘R’ indicating recipe and includes hour, minute, second, index information.
(c) In case backup file is created at the same time in terms of second, index information at the end of file name increases.

3. Path structure in case of screen backup

(1) Directory named ‘Screen Image’ is created under USB storage equipment root directory.
(2) Directory whose name is year; month is created under Screen Image directory.
(3) The lower directory structure is same as that of logging.
(4) Name of screen image backup file includes hour, minute, second information.
(a) Backup file is created in bitmap format.
(b) File name starts with ‘S’ and includes hour, minute, second, index information.
(c) In case backup file is created at the same time in terms of second, index information at the end of file name increases.

4. Structure of path at memo backup

(1) ‘Memo’ directory will be formed at the sub route directory of USB storage device.
(2) Directory in the name of Year and Month will be formed below the Memo Directory.
(3) Structure of directory thereafter is same as that of logging backup route.
(4)Memo backup file has the name made of hour/minute/second when it was created.
(a) Backup file is created in the type of bitmap.
(b) File name starts with ‘M’ that represents the screen image, which includes the index information of hour, minute, and
second thereafter.
(c) If the backup file is created at the same time up to the second, it increases the index information at the end.

5. Structure of path at live image recording

(1) ‘Movie’ directory will be formed at the sub route directory of USB storage device.
(2) Recorded live image is stored below the Movie Directory.
(3) Live image file has the name made of year/month/date/hour/minute/second information when it was
created.
(a) Backup file will be created in AVI type. H.264 and MP3 were used for Video CODEC and Audio CODEC
respectively.
(b) File name starts with ‘MOV’ that represents screen image, which includes data and hour information
thereafter.
(c) Live image can be stored up to the number 1,000 files. This number can be designated at the special device settings of
XP-Builder.

6. Structure of path when Blue Screen of camera image and live image is created
(1) ‘MovieStill’ directory will be formed at the sub route directory of USB storage device.

6-3
 Chapter 6 Backup files by using Storage Devices

(2) Recorded live image will be stored below MovieStill directory.

(3) Blue screen image file has the name made of year/month/date/hour/minute/second information when it was
created.
(a) Backup file will be created in JPG type.
(b) File name starts with ‘STL’ that represents screen image, which includes data and hour information
thereafter.
(c) Live image can be stored up to 1,000 files. This number can be designated at the special device settings of XP-
Builder.

Remark

(1) When changing device time, in case of changing current time into after time, we guarantee the normal
operation. But in case of changing current time into early time, we don’t guarantee the normal operation. In this
case, you have to delete directory including the changed hour and its lower directory for normal operation. For
example, if you change time from December 10th to December 5th, you have to delete year, month directory
created in December 10th and restart the device
(2) Sorting by project is not supported for each logging, recipe, screen image. For example, there are no.1, 2, and
3 logging groups in the project A. And in case each logging group backups the file, 1, 2, 3 directories are
created and each data is saved under each directory. Then, in case file backup occurs in the project B having
no.1, 2 logging group, backup file is created in same directory of project A. In this case, you have to sort the
backup files of project A and B based on the created time.

6-4
 Chapter 6 Backup files by using Storage Devices

6.2 Operation Setting when there is no space for Backup

You can designate in the XP-Builder whether to cancel the backup or delete the oldest backup file and execute
backup when there is no space in the storage equipment.
[Project Property Setting -> Storage Settings -> Backup Storage -> Delete old file if disk full]

1. In case of backup, deleting the oldest data

(1) In case there is no space for backup, searches the oldest year, month directory under Logging, Recipe,
Screen Image. (But in case of Logging, finds under Logging number directory. That is, when executing
backup about Logging number 2, in case there is no backup data in Logging number 2 directory and there is data
only in logging number 1, data of logging number 1 is not searched/deleted.)
(2) Searches the oldest day directory under the oldest year, month directory.
(3) Searches the oldest hour directory under the oldest day directory.
(4) Deletes the oldest backup file under the oldest hour directory.
(5)Checks the space and if more space is necessary, the above steps of (1) ~ (4) are repeated and checks the
space.
(6) When deleting file, in case all data in time directory are deleted, relevant hour directory is deleted.
(7) When deleting hour directory, in case all hour directories in day directory are deleted, relevant hour
directory is deleted.
(8) When deleting day directory, in case all day directories in year, month directory are deleted, relevant year,
month directory is deleted.

Remark

(1) In unknown directory or file (user file or directory), searches the oldest thing among normal backup files except
unknown directory or file.
(2) In case there is nothing except user data in now searched directory, backup operation fails. XGT Panel
can’t delete user data, at this point, operation stops.

6-5
 Chapter 6 Backup files by using Storage Devices

6.3 Monitoring Connection Status of External Storage Equipment

XGT Panels monitors connection status about external storage equipment designated when setting backup path in
XP-Builder. The following figure is backup path specified in XP-Builder.

In order to use this monitoring function, you have to set about system alarm window, and then the project should be
downloaded.

6-6
 Chapter 6 Backup files by using Storage Devices

In case USB storage equipment is removed during operation after setting the path for saving Logging backup file as
USB storage equipment and downloading the project into device, the designated system alarm (HS951.0) is set. In
case storage equipment is equipped again, alarm is reset.
In case USB storage equipment is removed during operation after setting the path for saving Recipe backup file as USB
storage equipment and downloading the project into device, the designated system alarm (HS951.1) is set. In case storage
equipment is equipped again, alarm is reset.
In case USB storage equipment is removed during operation after setting the path for saving Screen Image
backup file as USB storage equipment and downloading the project into device, the designated system alarm
(HS951.2) is set. In case storage equipment is equipped again, alarm is reset.

Internal address of the designated system alarm can be checked in XP-Builder as follows.

6-7
 Chapter 7 Maintenance

Chapter 7 Maintenance
To keep the XGT Panel best, examine the XGT Panel.

7.1 Maintenance

Because an error may be developed by environment, the periodic maintenance is needed. You should check the following
categories once or twice every 6 months.

Maintenance category Criterion Action

Within the power change range Modify the source of electric power in order to be in
Power
(Within 15% / +10%) the fluctuation range of a permissible voltage.
Operating
0 ~ + 50℃
temperature Modify the operating temperature and humidity to be
Operating proper.
Environment 10 ~ 85%RH
humidity
Use the anti-vibration rubber and make a count
Vibration No vibration
measure.
Getting loose of power terminal There is no unwinding Screw the unwound terminal.
Getting loose of
There is no unwinding Screw the unwound terminal.
communication connector
Amount of reserved part and
Reserved part reservation Refill the insufficiency and improve the reservation.
Check the status
No gap between the gasket and
Gasket installation status Replace gasket or affix brackets firmly
panel.
Gasket status No damage or deterioration Replace gasket
Front Panel status check No damage or deterioration Use a dry cloth to remove dust and foreign matter.

7.2 Daily Maintenance

Check the followings daily.

Maintenance category Maintenance contents Criterion Action

Mounting status Check the brackets Should be mounted firmly Retighten screws

Loose terminal screws Not loose Retighten screws

Power terminal status Reduce the distance between
Keep the proper distance. Correction
compressed terminals.
Communication connector
Unwinding of fixed screw Not loose Retighten screws
status
Indication LED Check the lighting Blue LED should be turned on Refer to the Appendix 1.
No pollution such as water drops or
Touch panel surface state Check the touch panel Surface wiping
oil

7-1
 Chapter 7 Maintenance

7.3 Periodical Maintenance

Check the followings once or twice every six months and take measure.

Maintenance
Maintenance category Criterion Action
method
Surrounding
0 ~ 50 C
Temperature Measure through Modify it to meet
Surrounding Temperature the general standard.
Environment 10 ~ 85%RH
Humidity /Hygrometer Measure (Environment standard
Surrounding of corrosive gas in the panel)
No corrosive gas.
pollution degree
Unwinding, swing Move XGT Panel Fixed firmly Retighten screws
XGT Panel Use a dry cloth to
Status Dust, foreign
Visual check Not loose remove dust and
matter adhesion
foreign matter.
Retighten screw with
Looseness Not loose Retighten screws
Screwdriver
Reduce the distance
Keep the proper
between compressed Visual check Correction
Connection distance.
terminals.
status
Wind the fixed screw of
Loose connectors Visual check Not loose
connector
Retighten screw with
Loose brackets Not loose Retighten screws
Screwdriver
Check the power
AC: 100~240V Supply
Power voltage maintenance voltage of input terminal
DC: 24V power modification
of power by test
 Check the total of
Check when battery is If guarantee duration is
power stoppage time
exchanged and voltage exceeded even tough
and guarantee
Battery drop is indicated. there is no battery
duration
(It is expressed voltage drop indication,
 There is no battery
by system alarm) change the battery.
voltage drop indication
Check the guarantee When error occurs,
LCD Backlight maintenance Visual check
duration change the backlight.
When error occurs,
No damage or
Touch Screen error Visual check change the Touch
Scratches and Pollution
Panel
Touch status
No damage or Change the touch pad
faulty touch pad Visual check Scratches in case of
/contamination an abnormality

7-2
 Chapter 7 Maintenance

Maintenance
Maintenance category Criterion Action
method
• Damage or scratches
/contamination
Front sheet damage and Replace front sheet in
Visual check nonexistent
deformation case of an abnormality
• No front
sheet deformation

7-3
 Chapter 7 Maintenance

Remark

(1) Battery exchange time is expressed by alarm. System alarm is expressed when system alarm
category is set at the XP-Builder as follows.

(2) Replace Battery With Hitachi Maxell, Part No. CR2032 Only. Use of another battery may present a
risk of fire or explosion. See User Manual for safety Instructions.

WARNING: Battery may explode if mistreated. Do not recharge, disassemble or dispose of in fire.

(3) As the iXP2 model has the integrated LCD and backlight, the LCD should be replaced when the life is
over or it is out of order.

(4) One of the ESD prevention measures, please use after wiping with a damp cloth.

7-4
 Chapter 8 EMC Standard Certification

Chapter 8 EMC Standard Certification

8.1 Requirement for EMC Standard Certification

EMC command is regulated on “It doesn’t produce the Strong electromagnetic waves: Emission” and “It is not
affected by electromagnetic wave from external: Immunity”. The following is describing the contents to meet the
EMC command when configuring the system by using the XGT Panel. This is a summary document for the
request and standard which our company has obtained from EMC but we don't assure that all devices
manufactured according to these contents are not suitable for the below standards. The final manufacturer needs
to finally judge about the fitness method or fitness judgment of EMC command.

8.1.1 CE Standard Certification

In case of XGT Panel, the EN61000-6-4, EN61000-6-2, EN61000-3-2, and EN61000-3-3 of CE standards were
applied.

Applied Standards Results

1. Emission
Conducted Disturbance EN61000-6-4:2007 / A1 : 2011 C
Radiated Disturbance EN61000-6-4:2007 / A1 : 2011 C
Harmonic Current Emission EN61000-3-2:2014 N/T
Voltage Change, Fluctuations and Flicker EN61000-3-3:2013 N/T
2. Immunity
EN61000-6-2:2005 / AC : 2005
Electrostatic Discharge C
EN61000-4-2:2009
EN61000-6-2:2005 / AC : 2005
Radio-Frequency Electromagnetic Field C
EN61000-4-3:2006 / A1 : 2008 / A2 : 2010
EN61000-6-2:2005 / AC : 2005
Fast Transient C
EN61000-4-4:2004 / A1 : 2010
EN61000-6-2:2005 / AC : 2005
Radio-Frequency Continuous Conducted C
EN61000-4-6:2009
EN61000-6-2:2005 / AC : 2005
Power-Frequency Magnetic Fields N/T
EN61000-4-8:2010
EN61000-6-2:2005 / AC : 2005
Surges C
EN61000-4-5:2006
EN61000-6-2:2005 / AC : 2005
Voltage Dips and Interruptions N/T
EN61000-4-11:2004

C=Comply NC=Not Comply N/T=Not Tested N/A=Not Applicable

8-1
 Chapter 8 EMC Standard Certification

Directive:

Electromagnetic Compatibility Directive 2014/30/EU amended by the Directive 93/68/EEC

8.1.2 KC Standard Certification

The XGT Panel acquire the electromagnetic fitness registration (KC specification) certified by wave laboratory
under information-communication part.

A grade device

This device acquires KC for industrial use.

If device is not purchased properly, exchange it to device for home use.

8.2 Requirement for Low Voltage Command Suitability

It is required to get the needed Stability for the device operated at AC50~1000V, DC75~1500V’s power. The following
describes attention about installation and wiring for the suitability when using the XGT Panel. Though the following
data is made by requirement of regulation and standard, we don’t guarantee that all devices are suitable for the above
command. The method to be suitable for the EMC command and judgment of suitability should be finally made by
device manufacturer himself.

8.2.1 Standard Certification for XGT Panel

XGT Panel is according to the EN61131-2:2007 (stability of device used in the measure, control laboratory).

8.2.2 Selection of XGT Panel

(1) iXP2-08xxA, iXP2-10xxA, iXP2-12xxA, iXP2-15xxA
Power module with rated input voltage of AC100 / 240V has hazardous voltage (voltage of 42.4V peak or more) inside.
Therefore, the CE marked product is reinforced and insulated between the internal primary and secondary
(2) iXP2-08xxD, iXP2-10xxD, iXP2-12xxD, iXP2-15xxD
I/O modules with a DC 24V rating or less are out of the low voltage command target range.

8-2
 Appendix 1. Troubleshooting

Appendix 1 Troubleshooting

1. Type of Problems

It classifies problems from XGT Panel including an indicated figure, indication of the object, and problems
appeared when downloading. Refer to the following chart.

Classification of problem Description

Malfunction when starting.
Problem when starting
☞Please refer to the 2. Problem when starting.
Problem after the In case that there is no reaction when touching.
monitor on ☞ Please refer to the 3. Problem after the Monitor on.
Display problem of In case that the figure or object is different from when editing.
figure and object. ☞ Please refer to the 4. Indication problem of figure and object.
In case that communication is not executed properly.
Communication problem
☞ Please refer to the 5. Communication problem.
In case that USB device is not working for a while when USB memory is
USB Removal of
removed.
Memory Card
☞ Please refer to the 6. USB Removal of Memory Card
External memory If external storage device such as USB, SD card is not recognized
recognition problem ☞ Please refer to the7. External Memory Recognition.
If the touch is not recognized normally
Touch recognition problem
☞ Please refer to the 8. Touch recognition.
Error message In case that an error message occurs when operating the XGT Panel.
when executing program ☞ Please refer to the 9. Error message when executing program.

APP1-1
 Appendix 1. Troubleshooting

2. Problems when Starting

Question Why does black screen show up when turning on the device?

Phenomenon When turning on the device, black screen shows up and the booting is impossible.

< Cause >

(1) Because the device is not set as a booting mode.
(2) Black screen may appear because of malfunction of backlight.

<Solution>
(1) Because the device is not set as a booting mode, the above problem can occur.
Check whether No. 5 switch at DIP switch in the back of the device is in B direction or not.
B direction is a booting mode.

When is the color of LED changed?

Please check the followings.

Display color Contents

BLUE Power is supplied to XGT Panel

When applying the option, ‘Go to Screen after boot up’, it displays “Failed to load image files”
Question
as the monitoring has not been started.

After storing images in the USB storage device and then selecting the option “Go to Screen
Phenomenon after boot up” in the start menu, in case when re-permitting the power of the equipment, the
message like “Failed to load image files” is displayed and the monitoring is not started.

<Cause>
(1) In case when it is connected with the USB storage device, the recognition of the USB is delayed.

<Solution>
(1) In case when the recognition speed is delayed due to the characteristics of the USB storage device,
remove the USB storage device and then reinstall it.

Question When the power is re-permitted, the USB storage device (or USB mouse) is not recognized.

When the USB storage device was initially installed, it was normally recognized. However, it is
Phenomenon
not recognized after the power is re-permitted.

<Causes>
(1) Due to the option of the ‘Reset USB Power’ of the equipment, there could problems in the recognition
process.
(2) Depending on the USB storage device, it may not be smoothly recognized.

APP1-2
 Appendix 1. Troubleshooting

<Solution>
(1) If the power initialization option (“Reset USB Power”) of the equipment is selected, cancel the selection
and then permit the power again. The “Reset USB Power” option is an additional function to improve
the initialization of the storage device with slow recognition speed or low recognition ratio. Depending
on the characteristics of the storage device, however, the power initialization can be an obstacle to the
initialization work. Thus, depending on Phenomenon, select what has higher recognition ratio by
properly using the power initialization option.
(2) Depending on the characteristics of the storage device, it may not be recognized. Use another USB
storage device showing higher recognition ratio.

APP1-3
 Appendix 1. Troubleshooting

3. Problems after the Monitor on

Question When touching the screen it reacts in a different area or it may not react at all?

Phenomenon When touching the screen it reacts in a different area or it may not react at all.

< Cause >

(1)Touch’s Calibration setting is not proper.
(2) Touch panel may be a break down.

<Solution>
(1) Redo Calibration setting about touch. Refer to the [Device manual Ch.4.1 Touch Calibration].
(2) It you can’t go to setting menu, connect mouse to USB port and use mouse.

Question Buzzer does not sound.

Phenomenon When pressing buzzer, buzzer does not sound.

< Cause >

(1) When that the switch operates but the buzzer doesn’t sound, the buzzer is set as no sound.
(2) If the switch doesn’t work too, it seems that some error occurs in the touch function.

<Solution>
(1) Redo environment setting for buzzer to sound. Refer to the [device manual Ch.4.7 Environment Setting].
(2) After setting to use buzzer, check whether the buzzer sounds or not in the 1)’s setting windows.

Question Lack of system memory system alarm occurs.

After the system alarm about the lack of system memory occurs, XGT Panel itself closes the
Phenomenon
monitoring and then moves to the start menu in unspecific time without user’s operation.

<Causes>
(1) The memory usage could be exceeding 95%.
(2) The memory usage can be a bit increased when floating pop-up windows or moving to several screens
during monitoring. In case when the number of image used for project is a lot, the memory usage can
more easily reach the limit. In this case, XGT Panel closes the monitoring by itself and then takes an
action to secure the memory again.

<Solution>
(1) In case of using vector image instead of raster image, the memory share can be reduced. In the graphic
library of XP-Builder, the image group marked as OOO_R is the raster image group while the image
group marked as OOO_V is the vector image group.
(2) In case when the monitoring is closed down due to the increase of the memory share in spite of the
image change operation, contact the A/S center close by.

APP1-4
 Appendix 1. Troubleshooting

After continuously adding projects to the screen, and adding/editing objects, the operation
Question
speed has been slowed down.

After adding projects to the screen and also adding/editing objects, it feels like the operation
Phenomenon
speed of XGT Panel gets slowed down.

<Causes>
(1) The amount of image used for projects is big.
(2) In order to increase the screen operation speed, XGT Panel maintains the used images in the memory in
advance. Since the memory resource has limitation, they cannot be maintained in the memory once the
amount of image exceeds a certain limit. Whenever they are needed, thus, they are read from the file
system and then expressed on the screen. This could be the reason why the screen operation speed gets
slowed down.

<Solution>
(1) In case of using vector image instead of raster image, the memory share can be reduced. In the graphic
library of XP-Builder, the image group marked as OOO_R is the raster image group while the image
group marked as OOO_V is the vector image group.
(2) In case when there is no proper vector image, the desired image can be composed by using various
functions of figures (circle, square, straight line and etc.).
(3) Removing unnecessary background screen, the screen is composed by applying the background colors.

APP1-5
 Appendix 1. Troubleshooting

4. Display Problem of Figure and Object

The shape of object is not shown or the number or character value which has to be shown is
Question
not shown

The shape of object is not shown or the number or character value which has to be shown is
Phenomenon
not shown.

<Cause>
(1) The connection with PLC connected with each project is disconnected or NAK occurs.

<Solution>
(1) When the communication is executed at first, Check the cable connected with PLC is OK or not.
(2) If object where the offset is set is not shown, check whether address range is exceeded or not.
(3) In case that communication is not OK, when communication is abnormal, the following message shows
up in the XGT Panel.

Object type Phenomenon

Bit Switch The switch is expressed but it doesn’t work.
Word Switch The switch is expressed but it doesn’t work.
Change Screen Switch The switch is expressed but it doesn’t work.
Special Switch The switch is expressed but it doesn’t work.
Multi Switch The switch is expressed but it doesn’t work.
Bit Lamp Image is not shown.
Word Lamp Image is not shown.
N-State Lamp Image is not shown.
Clock Present time is shown.
Message is not shown. When designating the background image, image is shown
Bit Message
as it is.
Message is not shown. When designating the background image, image is shown
Word Message
as it is.
The value is not shown. When designating the background image, image is shown
Numeric Display
as it is.
The value is not shown. When designating the background image, image is shown
Numeric input
as it is.
Character string is not shown. When designating the background image, image is
Text Display
shown as it is.
Character string is not shown. When designating the background image, image is
Text Input
shown as it is.
The window screen set in the object is not shown. But if communication is set with
Bit Window
other object in the same window screen, it can be shown by that object.
The window screen set in the object is not shown. But if communication is set with
Word Window
other object in the same window screen, it can be shown by that object.
The part screen set in the object is not shown. But if communication is set with
Bit Part
other object in the same part screen, it can be shown by that object.

APP1-6
 Appendix 1. Troubleshooting

Object type Phenomenon

The part screen set in the object is not shown.
Word Part But if communication is set with other object in the same part screen, it can be
shown by that object.
Animation Animation is not shown.
Graph is not shown. When designating the background image, image is shown as
Bar Graph
it is.
Graph is not shown. When designating the background image, image is shown as
Pie Graph
it is.
Graph is not shown. When designating the background image, image is shown as
Meter Graph
it is.
Graph is not shown. When designating the background image, image is shown as
Closed Graph
it is.
X, Y axis is shown normally but trend axis is not normally shown.
Trend Graph
When designating the background image, image is shown as it is.
Change doesn’t occur. When communication is abnormal, alarm occurs because it
History Alarm Viewer can’t know the status of alarm target device. But previous alarm data shows up as
it is.
Data list Value is not shown. Lattice of viewing data list of object is shown as it is.
Change doesn’t occur. When communication is normal, the recorded log data is
Logging Viewer
shown normally. But, log data is shown as # when communication is abnormal.
Change doesn’t occur. Because it shows the group of alarm already developed,
Navigator though communication is abnormal, if it has alarm data already developed, it
shows the name of group where each alarm is included.

Question The number indication object value is shown as # or ~

The number indication object value is shown as # or ~.

Phenomenon
(Same phenomenon occurs at the number input device, viewing data list, and viewing logging)

<Cause>
(1) This happens when digit is not correct or type is not BCD.

<Solution>
(1) When the number to be expressed exceeds the number set in the object, # is expressed. In case of this,
set the digit largely and after download again, execute program again.
(2) When the numeric display object is expressed as BCD type, the data whose type is not BCD is
expressed as ~. In case of this, adjust device value as BCD type.
(3) This phenomenon occurs at the data list object, numeric input, numeric display device, and logging
viewer.

APP1-7
 Appendix 1. Troubleshooting

Question After switching the screen, the previous screen remains for a few minute

After switching the screen, when there is no background or image in the part or number
Phenomenon
indication device, the previous screen remains for a few minute because of change of part

< Cause >

(1) After switching the screen, when connection is set up multiply or communication time-out occurs, the
screen of previous part remains in some object.

<Solution>
(1) It is normal status. In case that multiple connection or communication is not good, when switching the
screen, the remains of previous screen can occur during the time-out hour.

Question The folded object doesn’t sequentially show up

Phenomenon The number under the data list shows up above data list.

< Cause >

(1) The device value is expressed at the top of object screen.

<Solution>
(1) It is normal status. The folded window or part object is not included in screen, regardless of sequence of
drawing, the object changed recently is expressed at top of screen. So if possible, do not fold the object
in screen.

Question The object always shows up above the figure

I downloaded the figure above the object in XP-Builder, but the object always shows up above
Phenomenon
the figure.

< Cause >

(1) In XGT Panel, The object always shows up above the figure.

<Solution>
(1) It is normal status. The object always shows up above figure in the XGT Panel.

APP1-8
 Appendix 1. Troubleshooting

5. Communication Problems

Question It seems that communication does not work

On the screen where the object is not many, communication works but when you move the
Phenomenon
screen where the object is many, timeout occurs.

< Cause >

(1) In the device setting, the communication time-out is set to be too short.

<Solution>
(1) It occurs because timeout is set much smaller than sum of request time of communication data and
response time from PLC. In the device setting at the XP-Builder, after setting communication time out to
be big, download program and execute again.

Question It seems that communication doesn’t work.

Phenomenon Communication doesn’t work.

< Cause >

(1) Communication setting or cable may be not normal.

<Solution>
(1) In case of RS-232C, check whether connection setting is normal or not in XP-Builder.
(2) In case of RS-422/485, check whether station and communication connection setting is normal or not.
(3) If 1), 2) is normal, do diagnosis about PLC-RS232C, PLC-RS485/422 at the Serial diagnosis screen of
device menu. Refer to the [Device manual ch.5.6 Serial Communication Diagnosis]
(4) If 3) is normal, check whether connection cable has error or not.
(5) In case of Ethernet, check the port and IP setting about relative PLC.
(6) In case of Ethernet, make sure that the IP and port settings for the other PLC are correct.

Question It seems that communication doesn’t work.

Phenomenon Ethernet communication is connected slowly after monitoring starts.

< Cause >

(1) Subnet of Ethernet port is the same.

<Solution>
(1) If the subnets of the two Ethernet ports are the same, the initial connection may be delayed due to
the seek time.
(2) If possible, remove the Ethernet port's subnet.

APP1-9
 Appendix 1. Troubleshooting

Caution
► Before trial operation of the product, be sure to check if a normal communication is available
between XGT Panel and the subject device of control

APP1-10
 Appendix 1. Troubleshooting

6. USB Removal of Memory Card

Question When removing the USB memory equipment, device is stopped for some times.

Phenomenon This happens when doing data backup including logging, recipe.

< Cause >

(1) This happens because memory card is removed when doing data backup.

<Solution>
(1) If possible, when monitoring XGT Panel, do not remove the memory card and after going out to the
waiting screen, execute the removing.
(2) Inescapably you have to remove it during the operation, remove when backup does not occur. If the
above phenomenon occurs, it works normally after about 10 seconds.
(3) In case of USB memory, please remove it when the LED of USB external memory is not flickering.

Question After the repeated attachment/detachment of the USB storage device, it is not recognized

It can happen when the attachment/detachment of the USB device is repeated for a short
Phenomenon
period of time.

<Cause>
(1) When the USB device is recognized or removed, it takes a certain period of time(maximum a few
seconds) to recognize it. When the storage device is quickly installed/removed, however, it cannot be
normally recognized.

<Solution>
(1) It is recognized again after waiting for about a minute. Install it again after waiting for more than a minute.
(2) When removing/reinstalling the USB device, reinstall it after waiting for around 2-3 seconds.

Caution
► If you force to remove the data during the storage of data in the external memory, file may not
be stored in a normal condition or external memory may suffer from damage.

APP1-11
 Appendix 1. Troubleshooting

7. External memory recognition

Question USB, SD Card not recognized.

Phenomenon The USB or SD card is inserted but the unit does not recognize it.

<Cause>
(1) It appears when the USB memory or SD card is partitioned.

<Solution>
(1) Please format USB memory or SD card as one partition.

Caution
► If you forcefully remove the data from the external memory while it is being saved, the file may not be
saved properly or the external memory may be damaged.

8. Touch recognition

Question It recognizes that you have touched a place you do not want.

Phenomenon The place where I did not touch was touched.

<Caution>
(1) Check the surface of the touch panel for foreign matter such as water or oil.
(2) Check if the power or communication cable is passing on the surface of the touch panel.

<Solution>
(1) Clean the surface of the touch panel using a dry cloth or a towel
(2) When cleaning the surface of the touch panel, be sure to turn off the power to prevent malfunction
(3) Be careful not to let cables run near the touch panel

Caution
► The electrostatic touch panel may cause malfunction if liquids such as water or oil get on the surface.
► If you need to clean the unit, be sure to turn off the power before cleaning.

APP1-12
 Appendix 1. Troubleshooting

9. Error Message during Execution of Programs

In case that problems occur during execution of XGT Panel including the start of device, diagnosis of device and
environment setting, project download, monitoring of control device, and error messages occur as type of box. At
this time the message indicates the code made by 4 digit number. The front 2 number indicate code of object
and work, the rear 2 number is message number. In case that the present error message is indicated as [0101],
an error message occurs when doing diagnosis about the status of NVRAM. When an error message occurs,
refer to the row’s number and sequence and find the category of reason and measure.

Error code Occurren

Object ce Error message Reason and measure
Type Address
location
Failed to check whether backup
XGT NVRAM Data memory is normal or not. If this
0x01
Panel Access ... FAILED! symptom is repeated, contact the near
Customer Service Center.
Backup data is not valid. If this
XGT BATTERY STATUS ... symptom is repeated when turning
0x02
Panel NOT GOOD! power off and on, remove XGT Panel’s
power and exchange the battery.
The built-in Flash disk has an error.
XGT Write Operation
0x03 Contact the near Customer Service
Panel FAILURE!
Center.
Device The built-in Flash disk has an error.
0x01 XGT Read Disk Information
diagnosis 0x04 Contact the near Customer Service
Panel Error!
Center.
Check that CF card is empty, and equip
CF card and test again. If same
XGT Write Operation
0x05 symptom is repeated, CF card or CF
Panel FAILURE!
card slot of XGT Panel may have a
problem.
Check that CF card is empty, and equip
CF card and test again. If same
XGT Read Disk Information
0x06 symptom is repeated, CF card or CF
Panel Error!
card slot of XGT Panel may have a
problem.
You inputted the wrong time which is
XGT
0x01 Invalid timeout value. not within backlight setting time range.
Panel
Input the effective time.
There is no setting information data of
Device XGT Not found XGT Panel XGT Panel. If this symptom is repeated
0x02 0x02
setting Panel configuration file. when turning power off and on, contact
the near Customer Service Center.
Please enter an When setting IP, the values within
XGT
0x03 integer between 0 and 0~255 are effective. Input the value
Panel
255. within the above range.

APP1-13
 Appendix 1. Troubleshooting

Error code Occurren

Object ce Error message Reason and measure
Type Address
location
Viewing Now, there is no downloaded project so
XGT No project in XGT
device 0x03 0x01 you can’t see connection information.
Panel Panel.
information Download the project from XP-Builder.
Because of update error or Flash disk
Failed to Start engine. error, program can’t be executed. If you
XGT Panel XGT
0x04 0x01 Please update engine can update, redo the above procedure.
Update Panel
again. If you can’t, contact the near Customer
Service Center.
There is password in the each object.
When editing the project downloaded in
XGT
Switch h05 h01 Invalid password. the present device, input the
Panel
designated password at the project
property information.
Because of communication error, the
XGT
h01 Can't write Data. value can’t be inputted. Check the
Panel
communication status and input again.
XGT You tried to input with no value. Input
h02 No input Data.
Panel the value
Number XGT Exceeded the max You exceed the maximum length to
0x03
indication Panel length. input.
device/ 0x06 XGT Exceeded the You exceed the maximum value to
0x04
Number Panel minimum Value. input.
input device XGT Exceeded the You exceed the minimum value to
0x05
Panel maximum Value. input.
When you input the value, input can’t
XGT be done because of wrong input. Check
0x06 Invalid at Input Case.
Panel the input condition of each object in the
Builder and input again.
Lamp 0x07 None
Character
indication
device/ 0x08 None
Character
input device
Message 0x09 None
Clock 0x0A None
Animation 0x0B None
Graph 0x0C None
Window 0x0D None
Part 0x0E None
History
0x0F None
alarm
Flow alarm 0x20 None

APP1-14
 Appendix 1. Troubleshooting

Error code Occurren

Object ce Error message Reason and measure
Type Address
location
System
0x21 None
alarm
Scheduler
0x22 None
related
Recipe
0x23 None
related
Logging
0x24 None
related

Data list 0x25 None

Abnormal send-
Communication status is abnormal.
XGT payload. Please
0x00 Check the connection of
Panel download project
communication cable.
again.
This message shows up when making
it newly because there is no password
XP There's not Password
0x01 setting file in the device. When making
Builder File.
it newly, it is initialized with no
password.
It make new password setting file when
there is no password setting file. But
XP Failed to Create downloading is stopped when it fails to
0x02
Builder Password File. make this file because of device error.
If this problem is repeated, Contact the
near Customer Service Center.
Communication status is abnormal.
Project Route information is not correct to save
0x26 XP
download 0x03 Invalid Backup Media. project data. If this problem is repeated,
Builder
Contact the near Customer Service
Center.
In case that the version information file
doesn’t exist in the device, that file is
made newly. In case that the device
XP Failed to Create
0x04 has error and fails to make that file,
Builder version File.
download is stopped. If this problem is
repeated, Contact the near Customer
Service Center.
There is version information file. In
case that because of error of device, it
fails to read version information,
XP
0x05 File Size Error. because the device doesn’t know
Builder
version, download is stopped. If this
problem is repeated, Contact the near
Customer Service Center.

APP1-15
 Appendix 1. Troubleshooting

Error code Occurren

Object ce Error message Reason and measure
Type Address
location
In case of not reading file where project
property is included, download is
XP Failed to get Project
0x06 stopped. If this problem is repeated,
Builder ID.
Contact the near Customer Service
Center.
In case of not reading information about
alarm history because of error of
XP Failed to read history
0x07 NVRAM, download is stopped. If this
Builder alarm data.
problem is repeated, Contact the near
Customer Service Center.
Project is set to store data at CF card
equipped at device. By the way, now it
can’t read information about CF card.
XP Failed to read CF
0x08 Check the installation status of CF card
Builder Card information.
and if it is normal, check the CF card. If
this problem is repeated, contact
Customer Service Center.
Project is set to store data at USB
storage device equipped at device. By
the way, now it can’t read information
about USB storage device. Check the
XP Failed to read USB
0x09 installation status of USB storage
Builder information.
device and if it is normal, check USB
storage device. If this problem is
repeated, contact Customer Service
Center.
In case that it can’t know information
XP Failed to read Flash about memory status, download is
0x0A
Project Builder memory information. stopped. If this problem is repeated,
0x26
download contact Customer Service Center.
In case that because of error of Flash
Disk, it can’t delete the directory made
XP Failed to clear Temp temporally for download because of
0x0B
Builder Directory. error of Flash Disk, download is
stopped. If this problem is repeated,
contact Customer Service Center.
In case that it fail to delete the font file
Failed to delete Font of previous project because of error of
XGT
0x0C File. Please reboot XGT Panel, download is stopped. If this
Panel
XGT Panel. problem is repeated, contact Customer
Service Center.

APP1-16
 Appendix 1. Troubleshooting

Error code Occurren

Object ce Error message Reason and measure
Type Address
location
In case that it fail to delete the image
Failed to delete Image file of previous project because of error
XGT
0x0D File. Please reboot of XGT Panel, download is stopped. If
Panel
XGT Panel. this problem is repeated, contact
Customer Service Center.
In case that it fail to delete the sound
Failed to delete Sound file of previous project because of error
XGT
0x0E File. Please reboot of XGT Panel, download is stopped. If
Panel
XGT Panel. this problem is repeated, contact
Customer Service Center.
It can’t download part or fixed part in
There's no
case there is no downloaded project. In
XGT downloaded project. It
0x0F case of this, download again. If this
Panel needs to download
problem is repeated, contact Customer
whole project
Service Center.
When user change the storage location
of project data including image and
font, if there is not respective routine, it
Backup path is invalid. make newly. By the way, download is
XP Please check the path stopped in case it fails to make newly.
0x10
Builder that project is When it is designated as CF card, it
downloaded. can occur in case CF card is not
installed. If this problem is repeated
and not referred in the above, contact
Customer Service Center.
The project backup file downloaded
Failed to delete
already can be deleted because of
XGT previous project
0x11 error of XGT Panel. Reboot XGT Panel.
Panel archive. Please reboot
If this problem is repeated, contact
XGT Panel.
Customer Service Center.
When downloading, the log data area in
the NV-RAM is initialized in case of
Failed to delete past
selecting previous project’s the monitor
XGT project data files.
0x12 data deletion option. By the way, in
Panel Please download
case of failing this, downloading is
project again.
stopped. If this problem is repeated,
Project contact Customer Service Center.
0x26
download When downloading, the log data area in
Failed to initialize the NV-RAM is initialized in case of
LOGGING area in NV selecting previous project’s the monitor
XGT
0x15 RAM. Please data deletion option. By the way, in
Panel
download project case of failing this, downloading is
again. stopped. If this problem is repeated,
contact Customer Service Center.

APP1-17
 Appendix 1. Troubleshooting

Error code Occurren

Object ce Error message Reason and measure
Type Address
location
When downloading, the alarm history in
Failed to initialize the NV-RAM is initialized in case of
RECIPE area in NV selecting the previous project’s monitor
XGT
0x16 RAM. Please data deletion option. By the way, in
Panel
download project case of failing this, downloading is
again. stopped. If this problem is repeated,
contact Customer Service Center.
Failed to initialize The downloaded font file is moved into
ALARM area in NV original storage location but when this
XGT
0x17 RAM. Please fails, downloading is stopped. If this
Panel
download project symptom is repeated, contact
again. Customer Service Center.
The project data is divided into several
Failed to install font files according to the contents but when
XGT
0x18 files. Please download this fails, downloading is stopped. If this
Panel
project again. symptom is repeated, contact
Customer Service Center.
The data divided according to the
Failed to unmarshall contents is moved to the original
XGT download file. Please storage location but when this fails,
0x19
Panel download project downloading is stopped. If this
again. symptom is repeated, contact
Customer Service Center.
The downloaded project is not installed
Failed to install new
normally because of error of the Flash
XGT project data files.
0x1A Disk. Download the project again. If this
Panel Please download
symptom is repeated, contact
project again.
Customer Service Center.
The downloaded project zip file is
Failed to merge data moved to the original storage location
XGT
0x1B files. Please download but when it fails, downloading is
Panel
project again. stopped. If this symptom is repeated,
contact Customer Service Center.
There is a program to reboot engine
program after downloading in the
device but when it fails, this message
Failed to save new
shows up. But because the
XGT project archive. Please
0x1C downloading is completed if you reboot
Panel download project
engine directly, it works normally. The
again.
program name to reboot is startup.exe
and it can be installed by engine
upgrade function.

APP1-18
 Appendix 1. Troubleshooting

Error code Occurren

Object ce Error message Reason and measure
Type Address
location
Failed to XGP Panel
It can’t find software to reboot XGT
XGT startup program.
0x1D Panel.
Panel Please update XGT
Update the XGT Panel.
Panel Software.
The project data was not downloaded
Project data is not normally because of communication
XGT downloaded. Please error. Check the connection status of
0x1E
Project Panel download project communication cable and If this
0x26
download again. symptom is repeated, contact
Customer Service Center.
There is version information file but
XGT Failed to read Version when it can’t read file normally because
Panel/ information file. Please of the device error, downloading is
0x1F
XP- download project stopped because it doesn’t know
Builder again. version. If this symptom is repeated,
contact Custom Service Center

There is no USB or device status of

XGT Cannot find project
0x51 USB is not good or project is not saved
Panel data in USB Storage
properly.

The project is not saved normally in the

USB.
XGT Project information file
0x52 Check whether there is XP_Project
Panel is not in USB Storage.
folder and [project name].inf in the USB
or not.

It can’t read project information file

XGT Failed to read project because the project is not saved in the
0x53
Project Panel information file. USB normally. Save the project again
download from XP-Builder to the USB.
from USB 0x27
The connected device type is not same
storage
as the device type set in the project in
device
XGT Device type is not the USB. In case of this, project can’t
0x54
Panel matched. be downloaded into the device. Edit the
project again or download according to
the connected device.
Information about the password can’t
XGT Cannot read user be red because of the device error. If
0x55
Panel password. this symptom is repeated, contact
Customer Service Center.
When saving the project, the password
XGT Password is not inputted by user is not same as present
0x56
Panel matched. connection password. Input correct
password and save the project.

APP1-19
 Appendix 1. Troubleshooting

Error code Occurren

Object ce Error message Reason and measure
Type Address
location
There is version information file but
when it can’t read file normally because
Cannot read XGT
XGT of the device error, downloading is
0x57 Panel software
Panel stopped because it doesn’t know
version.
version. If this symptom is repeated,
contact Customer Service Center.
The version of XP-Builder where
XGT Panel software is
XGT project is saved is not compatible with
0x58 old version. Please
Panel present XGT Panel. Update the XGT
update XGT Panel.
Panel.
The version of XP-Builder where
XP-Builder is old
XGT project is saved is not compatible with
0x58 version. Please
Panel present XGT Panel. Update the XGT
update XP-Builder.
Panel.
There is storage structure version
information file. But when it can’t read
this file because of the device error,
XGT Cannot read download
0x59 downloading is stopped because it
Panel data format version.
doesn’t know the version. If this
Project symptom is repeated, contact
download Customer Service Center.
from USB 0x27 Download data format
storage XGT version is not Data storage type is not correct.
0x5A
device Panel matched. Please Update XGT Panel.
update XGT Panel.
Download data format
XGT version is not Data storage type is not correct.
0x5A
Panel matched. Please Update the XP-Builder.
update XP-Builder.
There is no project data file at
XGT Data file path is designated location. Check the
0x5B
Panel invalid. connection status of USB and if there is
no error, save the project to USB again.

The name of project data file is not

XGT Download file name saved correctly. Save the project at the
0x5C
Panel length is invalid. USB again. If this symptom is repeated,
contact Customer Service Center.
The project data file can’t be found.
Save the project data file at the USB
XGT Cannot find download
0x5D again. When this symptom is repeated,
Panel file.
check the USB. If there is no error,
contact Customer Service Center.

APP1-20
 Appendix 1. Troubleshooting

Error code Occurren

Object ce Error message Reason and measure
Type Address
location
The project data file is not saved
correctly. Save the project data file at
XGT Download file size is the USB again. When this symptom is
0x5E
Panel invalid. repeated, check the USB. If there is no
error, contact Customer Service
Center.
The project backup file which should be
XGT Cannot find project downloaded is not downloaded
0x5F
Panel backup file. because of communication error.
Download again.
The project backup file is saved
incorrectly. Save the project at the USB
storage equipment again. When this
XGT Project backup file
0x60 symptom is repeated, check the USB
Panel size is invalid.
storage equipment and if the USB is
normal, contact Customer Service
Center.
The font file’s name is saved
XGT Font file name length incorrectly. Save the project in the USB
0x61
Panel is invalid. again. If this symptom is repeated,
contact Customer Service Center.
The font file which is needed for project
is not saved in the USB storage
Project XGT Font file is not
0x62 equipment. Save the project in the
download Panel downloaded.
USB. If this symptom is repeated,
from USB 0x27
contact Customer Service Center.
storage
The font file is not saved correctly.
device
Save the project at the USB. Save the
XGT project at the USB. If this symptom is
0x63 Font file size is invalid.
Panel repeated, check the USB and if the
USB is normal, contact Customer
Service Center.
The data can’t be analyzed because
the project data file is not saved
correctly. Save the project at the USB
XGT Cannot unmarshall
0x64 again. If this symptom is repeated,
Panel download file.
check the USB and if the USB is
normal, contact Customer Service
Center.
The data of the project can’t be deleted
because of device error. If this
XGT Cannot delete
0x65 symptom is repeated, check the USB
Panel previous project data.
and if the USB is normal, contact
Customer Service Center.

APP1-21
 Appendix 1. Troubleshooting

Error code Occurren

Object ce Error message Reason and measure
Type Address
location
Downloaded font file is moved to the
original storage location. But when it
XGT Cannot move new font
0x66 fails, the downloading is stopped. If this
Panel files.
symptom is repeated, contact
Customer Service Center.
The project data classified according to
the content is moved to the original
XGT Cannot move new storage location. But when it fails, the
0x67
Panel project data files. downloading is stopped. If this
symptom is repeated, contact
Customer Service Center.
The downloaded project zip data is
moved to the original storage location.
XGT Cannot move project
0x68 But when it fails, the downloading is
Panel backup file.
stopped. If this symptom is repeated,
contact Customer Service Center.
XGT Panel software was already
XGT Previous instance is started. Reboot the device. If this
0x01
Panel not terminated. symptom is repeated, contact
Customer Service Center.
The XGT Panel software can’t initialize
the communication status normally.
XGT Start Server Fail. Check the communication status again.
0x02
Panel Restart XGT Panel If this symptom is repeated when
communication is normal, contact
Customer Service Center.
XGT Panel The XGT Panel software can’t initialize
0x28 the communication status normally.
booting
XGT Failed to Start Echo Check the communication status again.
0x03
Panel Server. If this symptom is repeated when
communication is normal, contact
Customer Service Center.
The XGT Panel software can’t initialize
the communication with the XP-Builder
normally. Check the communication
XGT Failed to accept
0x04 status again. If this symptom is
Panel connection.
repeated when communication is
normal, contact Customer Service
Center.

APP1-22
 Appendix 1. Troubleshooting

Error code Occurren

Object ce Error message Reason and measure
Type Address
location
In the present XGT Panel the new
updated XGT Panel software’s name
can not be changed.
After rebooting the XGT Panel, update
again. When rebooting, if you can’t start
engine, delete
XGT Failed to rename
0x05 \\FlashDisk\LSISProduct\UpdateNew.e
Panel UpdateNew.exe
xe in the XGT Panel. Then if you touch
Update.exe and execute the XGT
Panel, it can be update mode. Try
update again. If this symptom is
repeated, contact Customer Service
Center
The new module is downloaded by the
XGT Panel update but the previous
module is not deleted. Reboot the
device. If the XGT Panel software is not
XGT Failed to Delete started normally, touch
0x06
Panel Update.exe. \\FlashDisk\LSISProduct\Update.exe in
the XGT Panel. At this time, if XGT is
set as update mode, update again. If
this symptom is repeated, contact
Customer Service Center.
The device connection password can’t
be modified because of error of Flash
XGT Failed to modify
0x30 Disk of XGT Panel. Reboot the device.
Panel password file.
If this symptom is repeated, contact
Customer Service Center.
Password-related It failed to set and modify password
XGT command because of communication status error.
0x31
Panel transmission payload If this symptom is repeated, contact
Communica
error Customer Service Center.
tion
between There is no XGT
0x29 XGT The connection setting file of XGT
other XP 0x32 Panel connection
Panel Panel can’t be found.
Builder- setting file.
XGT Panel The modified information can’t be
Modified content can’t
saved at the connection setting file of
XGT be saved in the XGT
0x33 XGT Panel. If this symptom is
Panel Panel connection
repeated, contact Customer Service
setting file.
Center.
The XGT Panel’s time can’t be set. If
XGT
0x34 Failed to set the time this symptom is repeated, contact
Panel
Customer Service Center.

APP1-23
 Appendix 1. Troubleshooting

Error code Occurren

Object ce Error message Reason and measure
Type Address
location
Because the each module version
XGT
Failed to Create information can’t be read because of
Panel/
0x21 Initialized Module XGT Panel’s error, it failed to initialize.
XP-
Version File. If this symptom is repeated, contact
Builder
Customer Service Center.
XGT The each module version information
Panel/ Module version file can’t be read because of XGT Panel’s
0x22
XP- size is invalid. error. If this symptom is repeated,
Builder contact Customer Service Center.
XGT The each module version information
Panel/ Can't Read module can’t be read because of XGT Panel’s
0x23
XP- version file. error. If this symptom is repeated,
XGT panel Builder contact Customer Service Center.
0x30
S/W update The version information list to update is
empty. Check the module folder newly
designated at XP-
XP- There's no file to Builder and if there is no error,
0x24
Builder download. download XGT Panel module and try
update again. If this symptom is
repeated, contact Customer Service
Center.
The wrong file which is not in the new
module list of XGT Panel is
XP- Downloaded file is not
0x25 downloaded. Try update of XGT Panel
Builder Module to download.
again. If this symptom is repeated,
contact Customer Service Center.
The space to copy new module in XGT
Panel is not enough. After deleting the
unnecessary file or backing up the
XGT Not enough space in
0x26 previous file to the movable storage
Panel flash memory.
equipment, try update again. If this
symptom is repeated after deleting,
contact Customer Service Center.
XGT panel
0x30 The new module is not installed
S/W update
because of XGT Panel’s error. After
rebooting the device, touch
XGT Failed to Copy module \\FlashDisk\LSISProduct\Update.exe
0x27
Panel ~.dll and set the device as update mode.
Then update again. If this symptom is
repeated, contact Customer Service
Center.

APP1-24
 Appendix 1. Troubleshooting

Error code Occurren

Object ce Error message Reason and measure
Type Address
location
To reboot the engine is not available
because of wrong file which is
developed by downloading wrong
module or communication error.
Failed to Start Engine.
XGT Touch
0x28 Please update engine
Panel \\FlashDisk\LSISProduct\Update.exe
again.
and set the device as update mode.
Then update again. If this symptom is
repeated, contact Customer Service
Center.
It is failed to record the version
XGT Failed to write Data to information during update of XGT
0x2A
Panel Module version File. Panel. If this symptom is repeated,
contact Customer Service Center.
To reboot the engine is not available
because of wrong file which is
developed by downloading wrong
module or communication error.
XGT There's no Touch
0x2B
Panel downloaded file. \\FlashDisk\LSISProduct\Update.exe
and set the device as update mode.
Then update again. If this symptom is
repeated, contact Customer Service
Center.
To reboot the engine is not available
because of wrong file which is
developed by downloading wrong
(improper
module or communication error.
communication
XGT Touch
0x2C command)
Panel \\FlashDisk\LSISProduct\Update.exe
Current state is not
and set the device as update mode.
authorized.
Then update again. If this symptom is
repeated, contact Customer Service
Center.
To reboot the engine is not available
because of wrong file which is
developed by downloading wrong
(improper
module or communication error.
communication
XGT panel XGT Touch
0x30 0x2D command)
S/W update Panel \\FlashDisk\LSISProduct\Update.exe
A module to download
and set the device as update mode.
is not listed up yet.
Then update again. If this symptom is
repeated, contact Customer Service
Center.

APP1-25
 Appendix 1. Troubleshooting

Error code Occurren

Object ce Error message Reason and measure
Type Address
location
XGT can’t be set as update mode
because of XGT Panel error. After
downloading new XGT Panel module
through homepage, etc., copy
UpdateNew.exe file among new
module to the
XGT Failed to Initialize \\FlashDisk\LSISProduct\ directory of
0x2E
Panel Update program. XGT Panel through the movable
storage equipment. Then reboot the
XGT Panel and go update mode and
update again. If this symptom is
repeated, contact Customer Service
Center.

APP1-26
 Appendix2. Dimensions

Appendix 2 Dimensions (Unit: mm)

1. iXP2-08xxA/D

APP2-1
 Appendix2. Dimensions

2. iXP2-10xxA/D

APP2-2
 Appendix2. Dimensions

3. iXP2-12xxA/D

APP2-3
 Appendix2. Dimensions

4. iXP2-15xxA/D

APP2-4
 Appendix 3. Warranty and Environmental Policy

Appendix 3 Warranty and Environmental Policy

1. Warranty contents

One. Warranty
The warranty period for your product is 18 months from the date of manufacture.

2. Scope of warranty
Partial replacements or repairs are available for any faults that occur during the above warranty period.
However, please note that if it falls under the following, it will be excluded from the guarantee range.

(1) In case of improper condition, environment, or handling other than those specified in the instruction manual
(2) If the cause of the fault is something other than our own product
(3) If the product has been modified or repaired outside of the designated spot designated by the Company or the
Company.
(4) If the product is not intended for its original use
(5) When the product is shipped from the Company, due to unforeseen circumstances at the level of science or technology
(6) If there is no responsibility for other genius, fire, etc.

3. The above warranty is only the guarantee of the HMI unit.

2. Environmental Policy

LS ELECTRIC is following the environmental policy as follows.

Environment Product Disposal Guide

LS ELECTRIC LS ELECTRIC HMI can protect

As a management priority, the environment
All employees have a pleasant environment It is designed to be a product.
Do my best to If the product is discarded, it can be recycled
by separating it into aluminum, iron or
synthetic resin(Cover).

APP3-1
 www.lselectric.co.kr

■ Headquarter ■ Overseas Subsidiaries

LS-ro 127(Hogye-dong) Dongan-gu, Anyang-si, Gyeonggi-Do, 14119, • LS ELECTRIC Japan Co., Ltd. (Tokyo, Japan)
Korea Tel: 81-3-6268-8241 E-Mail: [email protected]
• LS ELECTRIC (Dalian) Co., Ltd. (Dalian, China)
■ Seoul Office Tel: 86-411-8730-6495 E-Mail: [email protected]
LS Yongsan Tower, 92, Hangang-daero, Yongsan-gu, Seoul, 04386, • LS ELECTRIC (Wuxi) Co., Ltd. (Wuxi, China)

Korea Tel: 86-510-6851-6666 E-Mail: [email protected]

Tel: 82-2-2034-4033, 4888, 4703 Fax: 82-2-2034-4588 • LS ELECTRIC Shanghai Office (China)

E-mail: [email protected] Tel: 86-21-5237-9977 E-Mail: [email protected]

• LS ELECTRIC Vietnam Co., Ltd.

■ Factory Tel: 84-93-631-4099 E-Mail: [email protected] (Hanoi)

Tel: 84-28-3823-7890 E-Mail: [email protected] (Hochiminh)
56, Samseong 4-gil, Mokcheon-eup, Dongnam-gu, Cheonan-si,
• LS ELECTRIC Middle East FZE (Dubai, U.A.E.)
Chungcheongnam-do, 31226, Korea
Tel: 971-4-886-5360 E-Mail: [email protected]
• LS ELECTRIC Europe B.V. (Hoofddorf, Netherlands)
Tel: 31-20-654-1424 E-Mail: [email protected]
• LS ELECTRIC America Inc. (Chicago, USA)
Tel: 1-800-891-2941 E-Mail: [email protected]

©2018. LS ELECTRIC Co., Ltd. All Rights Reserved. 2020.04