Scribd
Upload
36 views

FE 1-Chapter 3-1

1) The document discusses the design of shallow foundations, including general principles, loads on foundations, pressure distribution beneath foundations, and settlement of foundations. It provides guidelines from codes like Eurocode 7 for designing spread foundations to satisfy ultimate limit state and serviceability limit state criteria. 2) Worked examples are presented to demonstrate verification of strength and serviceability limit states for spread foundation design based on soil properties and structural loads. Detailed calculations are shown for foundation width, depth, bearing pressure, and settlements. 3) Recommendations are given for estimating total and differential settlements in sand and clay soils based on empirical equations from sources like Skempton and MacDonald as well as allowable settlement values from codes.

Uploaded by

Abreham Add
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
36 views

FE 1-Chapter 3-1

1) The document discusses the design of shallow foundations, including general principles, loads on foundations, pressure distribution beneath foundations, and settlement of foundations. It provides guidelines from codes like Eurocode 7 for designing spread foundations to satisfy ultimate limit state and serviceability limit state criteria. 2) Worked examples are presented to demonstrate verification of strength and serviceability limit states for spread foundation design based on soil properties and structural loads. Detailed calculations are shown for foundation width, depth, bearing pressure, and settlements. 3) Recommendations are given for estimating total and differential settlements in sand and clay soils based on empirical equations from sources like Skempton and MacDonald as well as allowable settlement values from codes.

Uploaded by

Abreham Add
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 73

FOUNDATION

ENGINEERING I
CEng 3204
CHAPTER THREE
Design of Shallow Foundations
General Principles of Foundation Design
• The usual approach to a normal foundation engineering problem is:

1. To prepare a plan of the base of the structure showing the various columns, load-bearing
walls with estimated loads, including dead load, live load, moments and torques coming
into the foundation units.
2. To study the tentative allowable bearing pressures allocated for the various strata below
the ground level, as given by the soil investigation report.
3. To determine the required foundation depth. This may be the minimum depth based on
soil strength or structural requirement considerations.
4. To compute the dimensions of the foundation based on the given loading and allowable
bearing pressure.
5. To estimate the total and differential settlements of the structure.
• If these are excessive the bearing pressure will have to be reduced or the foundation taken to a
deeper and less compressible stratum or the structure will have to be founded on piles or other
special measures taken
Loads on Foundation
• A foundation may be subjected to two or more of the following loads:

a. Dead load:

• Weight of structure

• All material permanently attached to structure

• Static earth pressure acting permanently against the structure below ground surface.

• Water pressure acting laterally against basement walls and vertically against slab.

b. Live load: temporary loads expected to be superimposed on the structure during its useful life.

c. Wind load:- lateral load coming from the action of wind and depends on the size, shape and dynamic properties of the
structure.

Local building codes provide magnitude of design wind pressure.

d. Earth-quake load:- lateral load coming from earth- quake motion.

-The total lateral force (base shear) at the base of a structure is evaluated in accordance with local
building code.

e. Dynamic load:- load coming from a vibrating object (machinery).

• In such case, separate foundation should be provided. The impact effect of such loads should be considered in
design.
Pressure Distribution Beneath Foundation
• The stability of a structure is majorly dependent on soil-foundation interaction.

• Even though they are of different physical nature, they both must be act together to get required

stability. So, It is important to know about the contact pressure developed between soil and
foundation and its distribution in different conditions.

• The pattern of the distribution varies according to the stiffness of the foundation and rigidity of the

soil.
Pressure Distribution Beneath Foundation
Pressure Distribution Beneath Foundation
• For design purpose, the contact pressure is assumed to be uniform

for all types of footings and all types of soils under symmetric loading.
Pressure Distribution Beneath Foundation
• Approximate contact pressure under a given symmetrical foundation
can be determined by flexural formula.
• The considered load lies within the kern of the footing
Pressure Distribution Beneath Foundation
• One-way eccentricity
Pressure Distribution Beneath Foundation
• Two-way eccentricity
Pressure Distribution Beneath Foundation
Pressure Distribution Beneath Foundation
• Two-way eccentricity
Pressure Distribution Beneath Foundation
• Two-way eccentricity
Pressure Distribution Beneath Foundation
• Two-way eccentricity
Pressure Distribution Beneath Foundation
• Two-way eccentricity
Pressure Distribution Beneath Foundation
• Two-way eccentricity
Pressure Distribution Beneath Foundation
Settlement of Foundations
Settlement of Foundations
Settlement of Foundations
Settlement of Foundations
1. Recommendation by Skempton and MacDonald

i. Settlements on sand

a) Isolated footings: /l = max/600, max  5.08cm

b) Raft foundations: /l = max/750, max  6.35cm

ii. Settlements on clay

a) Isolated footings: /l = max/1000, max  8.38 cm

b) Raft foundation: /l = max/1250, max  10.8cm


Settlement of Foundations
2. Recommendation by Bowles

Types of soil Type of foundations


Isolated Rafts
Sand 3.8cm 3.8-6.4cm

clay 6.4cm 6.4cm-10.2cm


Settlement of Foundations
2. Recommendation by Euro code 7 (ES EN 1997-1:2015)
Settlement of Foundations
2. Recommendation of Euro code 7 (ES EN 1997-1:2015)
Spread Foundation (ES EN 1997-1:2015)
• General
• Provisions apply to spread foundations including pads, strips and rafts.

• One criteria for a safe design is that the structure should not become unfit for use.

• The structure should not reach a limit state during its design life.

• Achieved by designing the structure to ensure that it does not reach two important limit

states.

1. Ultimate Limit State (ULS): concerned with the safety of the people and
of the structure. This requires the whole structure or its elements should
not collapse, overturn or buckle when subjected to the design loads.

2. Serviceability Limit State (SLS): concerned with comfort of occupants


and appearance of the structure.
Spread Foundation (ES EN 1997-1:2015)
• Limit States
Spread Foundation (ES EN 1997-1:2015)
• Design situation and actions
Spread Foundation (ES EN 1997-1:2015)
• Actions, characteristic and design value of actions
Spread Foundation (ES EN 1997-1:2015)
Spread Foundation (ES EN 1997-1:2015)
Spread Foundation (ES EN 1997-1:2015)
• Design and construction considerations
Spread Foundation (ES EN 1997-1:2015)
• In addition to fulfilling the performance requirements, the design of foundation width

shall take account of practical considerations such as economic excavation, setting


out tolerances, working space requirements and dimensions of the wall or column
supported by the foundation.
Spread Foundation (ES EN 1997-1:2015)
Spread Foundation (ES EN 1997-1:2015)
Spread Foundation (ES EN 1997-1:2015)
Spread Foundation (ES EN 1997-1:2015)
• Ultimate limit state
Spread Foundation (ES EN 1997-1:2015)
Spread Foundation (ES EN 1997-1:2015)
Spread Foundation (ES EN 1997-1:2015)
Spread Foundation (ES EN 1997-1:2015)
Spread Foundation (ES EN 1997-1:2015)
Spread Foundation (ES EN 1997-1:2015)
Spread Foundation (ES EN 1997-1:2015)
Spread Foundation (ES EN 1997-1:2015)
Spread Foundation (ES EN 1997-1:2015)
Spread Foundation (ES EN 1997-1:2015)
Spread Foundation (ES EN 1997-1:2015)
Spread Foundation (ES EN 1997-1:2015)
Spread Foundation (ES EN 1997-1:2015)
Spread Foundation (ES EN 1997-1:2015)
Spread Foundation (ES EN 1997-1:2015)
• Serviceability limit state
WORKED EXAMPLES
Verification of Strength and Serviceability(Limit State)
Worked Examples
1.
1
Worked Examples
Worked Examples
Worked Examples
Worked Examples
Worked Examples
Worked Examples
Worked Examples
Worked Examples
Worked Examples
Worked Examples
Worked Examples
Worked Examples
Worked Examples
Worked Examples
Worked Examples

2.
2
Worked Examples
Worked Examples
Worked Examples

Continue…….

You might also like