0% found this document useful (0 votes)
43 views

Dh-Ipc-Hfw1200sp-W I en

The document summarizes a user manual for a Dahua HD Mini IR Waterproof Fixed Network Camera. It has features such as multiple user rights, local and network storage of recordings, data transmission over Ethernet, supporting up to 20 network connections using protocols like HTTP and TCP/IP, web access for network management, and power options of external power adapter or Power over Ethernet. It also mentions log functions, system status display, auto day/night mode switching, and picture parameter configuration.

Uploaded by

h2oo2h
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
43 views

Dh-Ipc-Hfw1200sp-W I en

The document summarizes a user manual for a Dahua HD Mini IR Waterproof Fixed Network Camera. It has features such as multiple user rights, local and network storage of recordings, data transmission over Ethernet, supporting up to 20 network connections using protocols like HTTP and TCP/IP, web access for network management, and power options of external power adapter or Power over Ethernet. It also mentions log functions, system status display, auto day/night mode switching, and picture parameter configuration.

Uploaded by

h2oo2h
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 25

Dahua HD Mini IR Waterproof Fixed Network Camera User’s Manual

DH-IPC-1200SP-W

Version 1.2.5

Delta-Opti, 2016

Zhejiang Dahua Technology CO., LTD


Welcome
Thank you for purchasing our network camera!
This user’s manual is designed to be a reference tool for your system.
Please read the following safeguard and warnings carefully before you use this series product!
Please keep this user’s manual well for future reference!

i
Important Safeguards and Warnings
1.Electrical safety
All installation and operation here should conform to your local electrical safety codes.
The power shall conform to the requirement in the SELV (Safety Extra Low Voltage) and the Limited
power source is rated 12V DC or 24V AC in the IEC60950-1. (Refer to general introduction)
Please note: Do not connect two power supplying sources to the device at the same time; it may
result in device damage! The product must be grounded to reduce the risk of electronic shock.
We assume no liability or responsibility for all the fires or electrical shock caused by improper handling
or installation.
We are not liable for any problems caused by unauthorized modification or attempted repair.

2.Transportation security
Heavy stress, violent vibration or water splash are not allowed during transportation, storage and
installation.

3.Installation
Do not apply power to the camera before completing installation.
Please install the proper power cut-off device during the installation connection.
Always follow the instruction guide the manufacturer recommended.

4.Qualified engineers needed


All the examination and repair work should be done by the qualified service engineers.
We are not liable for any problems caused by unauthorized modifications or attempted repair.

5.Environment
This series network camera should be installed in a cool, dry place away from direct sunlight,
inflammable, explosive substances and etc.
Please keep it away from the electromagnetic radiation object and environment.
Please make sure the CCD (CMOS) component is out of the radiation of the laser beam device.
Otherwise it may result in CCD (CMOS) optical component damage.
Please keep the sound ventilation.
Do not allow the water and other liquid falling into the camera.
Thunder-proof device is recommended to be adopted to better prevent thunder.
The grounding studs of the product are recommended to be grounded to further enhance the reliability
of the camera.

6. Daily Maintenance
Please shut down the device and then unplug the power cable before you begin daily maintenance
work.

ii
Do not touch the CCD (CMOS) optic component. You can use the blower to clean the dust on the lens
surface.
Always use the dry soft cloth to clean the device. If there is too much dust, please use the water to
dilute the mild detergent first and then use it to clean the device. Finally use the dry cloth to clean the
device.
Please put the dustproof cap to protect the CCD (CMOS) component when you do not use the camera.
Dome enclosure is the optical component, do not touch the enclosure when you are installing the
device or clean the enclosure when you are doing maintenance work. Please use professional optical
clean method to clean the enclosure. Improper enclosure clean method (such as use cloth) may result
in poor IR effect of camera with IR function.

7. Accessories
Be sure to use all the accessories recommended by manufacturer.
Before installation, please open the package and check all the components are included.
Contact your local retailer ASAP if something is broken in your package.

Accessory Name Amount

Network Camera Unit 1

Quick Start Guide 1

Installation Accessories Bag 1

CD 1

Warranty Card and Certificate 1

iii
Table of Contents
1 General Introduction ...................................................................................................... 1

1.1 Overview ........................................................................................................... 1

1.2 Features ............................................................................................................ 1

1.3 Specifications .................................................................................................... 2

1.3.1 Performance ............................................................................................... 2

2 Framework..................................................................................................................... 9

2.1 Cable................................................................................................................. 9

2.2 Framework and Dimension ............................................................................. 10

3 Device Installation ....................................................................................................... 13

4 Quick Configuration Tool ............................................................................................. 15

4.1 Overview ......................................................................................................... 15

4.2 Operation ........................................................................................................ 15

5 Web Operation ............................................................................................................ 17

5.1 Network Connection ........................................................................................ 17

5.2 Login and Main Interface ................................................................................. 17

6 FAQ ............................................................................................................................. 19

Appendix Toxic or Hazardous Materials or Elements ........................................................ 20

iv
1 General Introduction
1.1 Overview
This series network camera integrates the traditional camera and network video technology. It adopts
video data collection, transmission together. It can connect to the network directly without any auxiliary
device.

This series network camera uses standard H.264 video compression technology, which maximally
guarantees the video quality.

It supports the IR night vision function. In the night environments, the device can use the IR light to
highlight the object which is suitable for the surveillance function in the low illumination environments.
The built-in waterproof design conforms to the IP 66 level. It has the sound waterproof function
suitable for use in the outdoor environments.

It can be used alone or used in a network area. When it is used lonely, you can connect it to the
network and then use a network client-end. Due to its multiple functions and various uses, this series
network camera is widely used in many environments such as home, office, bank, road monitor and
etc.

1.2 Features
 Different user rights for each group, one user belongs to one group.
User
 The user right shall not exceed the group right.
Management
 Support central server backup function in accordance with your configuration
and setup in alarm or schedule setting
Storage
 Support record via Web and the recorded file are storage in the client-end
Function PC.
 Support network storage function such as FTP.
Data  Support data transmission via Ethernet.
Transmission
 Network camera supports one-channel video data transmit to network
terminal and then decode. Delay is within 270ms (network bandwidth support
needed)
Network
 Max supports 20 connections.
Monitor  Adopt the following video transmission protocol: HTTP, TCP, UDP,
MULTICAST, RTP/RTCP, RTSP and etc.
 Support web access.
 Realize network camera configuration and management via Ethernet.
Network
 Support device management via web or client-end.
Management  Support abundant network protocols.
 External power adapter DC12V.
 Support PoE.
Power Warning!
 Do not connect these two power supplying sources to the device at the
same time; it may result in device damage!
 Log function
 Support system resource information and running status real-time display.
Assistant  Day/Night mode auto switch.(with ICR switch)
Function  Support picture parameter setup such as electronic shutter and gain setup.
 Backlight compensation: screen auto split to realize backlight compensation
to adjust the bright.

1
 Support digital WDR.
 Support video watermark function to avoid vicious video modification.
 Support dual bit streams, ACF.

1.3 Specifications
1.3.1 Performance
Please refer to the following sheet for network camera performance specification.
Model
IPC-HFW1100S IPC-HFW1105S
Parameter
Main Processor High performance DSP
System

OS Embedded LINUX
System Support real-time network, local record, and remote operation at the
Resources same time.
User Interface Remote operation interface such as WEB, DSS, PSS
System Status Bit stream statistics, log, and software version.
Image Sensor 1/4-inch CMOS
Video Parameter

Pixel 1280(H) *720(V)


Day/Night Mode Support day/night mode switch.
Gain Control Fixed/Auto
White Balance Manual/Auto
BLC On/Off
Auto/Manual
Exposure Mode
It ranges from 1/3 to 1/10000.
Video
H.264/H.264B/MJPEG
Compression
Standard

PAL:
Main stream(1280*720@25fps)
Video Frame extra stream(704*576@25fps),
Rate

NTSC:
Main stream(1280*720@30fps)
extra stream(704*480@30fps),
H.264H: 16Kbps-8192Kbps;
Video Bit Rate MJPEG: adjustable and bit rate is adjustable.
Support customized setup.
Support mirror.
Video Flip
Support flip function.
Snapshot Max 1f/s snapshot. File extension name is JPEG.
Privacy Mask Supports max 4 privacy mask zones
Video Setup Support parameter setup such as bright, contrast.
Video
Channel title, time title, motion detect, tampering.
Information
Lens 3.6mm, 6mm. Fixed focus.
Lens Interface M12. Lens is the default accessories
Video

396 (18*22) detection zones; sensitivity level ranges from 0 to 100;


area threshold ranges from 0 to 100.
Motion Detect
Activation event: video storage, image snapshot, log, email function
and etc.

2
p
Backu
d and
Recor
Storage
Support display network storage status
Management

Wire Network 1-channel wire Ethernet port, 10/100 Base-T Ethernet


Network

Standard HTTP, TCP/IP, ARP, IGMP, ICMP, RTSP, RTP,UDP, RTCP,


Network Protocol SMTP, FTP, DHCP, DNS, DDNS, PPPOE, UPNP, NTP, Bonjour,
SNMP.
Remote Monitor, system setup, file download, log information, maintenance ,
Operation upgrade and etc.

IR light IR distance 20~30m

Power DC12V power, PoE. DC12V


General Parameter

Power
4.5W MAX 3.6W MAX
Consumption
Working
-30℃~+60℃
Temperature
Working
≤95%
Humidify
Dimensions(mm) 70*66*155
Weight 620g 420g
Installation Installation with the bracket.

Model IPC-
Parameter HFW2200S-V2/ IPC- IPC- IPC-
IPC- HFW2205S-V2 HFW2100S-V2 HFW2105S-V2
HFW1200S
Main Processor High performance DSP
System

OS Embedded LINUX
System Support real-time network, local record, and remote operation at the
Resources same time.
User Interface Remote operation interface such as WEB, DSS, PSS
System Status Bit stream statistics, log, and software version.
Image Sensor 1/3-inch CMOS
Video Parameter

Pixel 2048(H)*1536(V) 1280(H)*960(V)


Day/Night Mode Support day/night mode switch.
Gain Control Fixed/Auto
White Balance Manual/Auto
BLC On/Off
Electronic Manual/Auto/Low noise/Low motion blur
Shutter It ranges from 1/3 to 1/100000.
Video
H.264/H.264B/H.264H/MJPEG
Compression
Standard

PAL: PAL:
Main stream(1920*1080@25fps) Main stream(1280*960@25fps)
Video Frame
extra stream(704*576@25fps), extra stream(704*576@25fps),
Rate

NTSC: NTSC:
Main stream(1920*1080@30fps) Main stream(1280*960@30fps)

3
extra stream(704*480@30fps), extra stream(704*480@30fps),

H.264H: 16Kbps-8192Kbps;
Video Bit Rate MJPEG: adjustable and bit rate is adjustable.
Support customized setup.
Support mirror.
Video Flip
Support flip function.
Snapshot Max 1f/s snapshot. File extension name is JPEG.
Privacy Mask Supports max 4 privacy mask zones
Video Setup Support parameter setup such as bright, contrast.
Video
Channel title, time title, motion detect, tampering.
Information
Lens 3.6mm, 6mm, 8mm. Fixed focus.
Lens Interface M12. Lens is the default accessories
Video

396 (18*22) detection zones; sensitivity level ranges from 0 to 100;


area threshold ranges from 0 to 100.
Motion Detect
Activation event: video storage, image snapshot, log, email function
and etc.
Backup
and
Record

Record Priority Manual > video detect > schedule

Storage
Support NAS storage
Management
Wire Network 1-channel wire Ethernet port, 10/100 Base-T Ethernet
Network

HTTP,TCP,ARP,RTSP,RTP,UDP,RTCP,SMTP,FTP,
Network Protocol DHCP,DNS,DDNS,PPPOE,IPv4/v6,QoS,UPnP,NTP,
HTTPS,Bonjour
Remote Monitor, system setup, file download, log information, maintenance ,
Operation upgrade and etc.
Platform
Interface Support ONVIF
Standard
IR light IR distance 30m
DC12V power, PoE.
Power
General Parameter

Note: 05 series does not support PoE.


Power
DC 12V 6W MAX
Consumption
Working
-30℃~+60℃
Temperature
Working
≤95%
Humidify
Dimensions(mm) 70*66*155
Weight
620g 420g 620g 420g
(excluding box)
Installation Installation with the bracket.

Model IPC-HFW4105S-V2 IPC-HFW4305S-V2


Parameter IPC-HFW4100S-V2 IPC-HFW4300S-V2
Main Processor High performance DSP
m
Syste

OS Embedded LINUX
System Support real-time network, local record, and remote operation at the

4
Resources same time.
User Interface Remote operation interface such as WEB, DSS, PSS
System Status Bit stream statistics, log, and software version.
Image Sensor 1/3-inch CMOS
Video Parameter

Pixel 1280(H)*960(V) 2048(H)*1536(V)


Day/night Support day/night mode switch
Gain Control Fixed/Auto
White Balance Manual/Auto
BLC On/Off
Manual/Auto/Low noise/Low motion blur
Exposure Mode
It ranges from 1/3 to 1/100000.
Video
Compression H.264/H.264H/MJPEG
Standard
PAL:
Main stream (2048*1536@20fps)
extra stream 1 (704*576@20fps)
PAL:
extra stream 2 (1280*720@1fps),
Main stream (1280*960@25fps)
extra stream 1 ( 704*576@25fps)
Main stream (1920*1080@25fps)
extra stream 2 ( 1280*720@8fps)
extra stream 1 ( 704*576@25fps)
extra stream 2(1280*720@11fps),

NTSC:
Video Frame
Main stream (2048*1536@20fps)
Rate
extra stream 1 (704*480@20fps)
NTSC:
extra stream 2 (1280*720@1fps),
Main stream (1280*960@30fps)
extra stream 1 ( 704*480@30fps)
Main stream (1920*1080@30fps)
extra stream 2 ( 1280*720@1fps)
extra stream 1 ( 704*480@30fps)
extra stream 2(1280*720@1fps),

Note:
Extra stream 2’s actual frame depends on device max capacity set
which can be adjusted within its range.
H.264H: 40Kbps-8192Kbps
Video Bit Rate MJPEG: 40Kbps-16384Kbps adjustable and bit rate is adjustable.
Support customized setup.
Support mirror.
Video Flip
Support flip function.
Snapshot Max 1f/s snapshot. File extension name is JPEG.
Privacy Mask Supports max 4 privacy mask zones
Video Setup Support parameter setup such as bright, contrast.
Video
Channel title, time title, motion detect, tampering, overlay.
Information
Lens 3.6mm, 6mm, 8mm. Fixed focus.
Lens Interface M12. Lens is the default accessories

396 (18*22) detection zones; sensitivity level ranges from 0 to 100;


area threshold ranges from 0 to 100.
Video

Motion Detect
Activation event: video storage, image snapshot, log, email function
and etc.
Rec
ord

Record Priority
Manual >Video detect>Schedule

5
Storage
NAS storage
Management
Wire Network 1-ch 10/100 Base-T Ethernet
Network

Standard HTTP, TCP/IP, ARP,IGMP, ICMP, RTSP, RTP,UDP, RTCP,


Network Protocol SMTP, FTP, DHCP, DNS, DDNS, PPPOE, UPNP, NTP, Bonjour,
SNMP, QoS, 802.1x
Remote Monitor, system setup, file download, log information, maintenance ,
Operation upgrade and etc
Protocol PSIA, ONVIF
IR light IR light 30M.
General Parameter

Power DC12V power, PoE.


Note: 05 series does not support PoE.
Power
DC 12V 3.7W MAX DC 12V 4.2W MAX
Consumption
Working
-30℃~+60℃
Temperature
Working
≤95%
Humidify
Dimensions(mm) 70*66*155
00 series:620g (excluding box)
Weight
05 series:420g (excluding box)
Installation Install with bracket.

Model
IPC-HFW1100S-W IPC-HFW2200S-W
Parameter
Main Processor High performance DSP
System

OS Embedded LINUX
System Support real-time network, local record, and remote operation at the
Resources same time.
User Interface Remote operation interface such as WEB, DSS, PSS
System Status Bit stream statistics, log, and software version.
Image Sensor 1/4-inch CMOS 1/3-inch CMOS
Video Parameter

Pixel 1280(H) *720(V) 2408(H) *1536(V)


Day/Night Mode Support day/night mode switch.
Gain Control Fixed/Auto
White Balance Manual/Auto
BLC On/Off
Auto/Low noise/ Low motion blur/ Manual
Exposure Mode
It ranges from 1/3 to 1/10000.
Video
Compression H.264/H.264B/MJPEG H.264/H.264B/H.264.H/MJPEG
Standard

PAL: PAL:
Main stream(1280*720@25fps) Main stream(1920*1080@25fps)
Video Frame
extra stream(704*576@25fps), extra stream(704*576@25fps),
Rate

NTSC: NTSC:
Main stream(1280*720@30fps) Main stream(1920*1080@30fps)

6
extra stream(704*480@30fps), extra stream(704*480@30fps),

H.264: 16Kbps-8192Kbps; H.264H: 16Kbps-8192Kbps;


MJPEG: adjustable and bit rate is MJPEG: adjustable and bit rate is
Video Bit Rate
adjustable. adjustable.
Support customized setup. Support customized setup.
Support mirror.
Video Flip
Support flip function.
Snapshot Max 1f/s snapshot. File extension name is JPEG.
Privacy Mask Supports max 4 privacy mask zones
Video Setup Support parameter setup such as bright, contrast and acutance.
Video
Channel title, time title, motion detect, tampering.
Information
Lens 3.6mm, 6mm. Fixed focus.
Lens Interface M12. Lens is the default accessories
Video

396 (18*22) detection zones; sensitivity level ranges from 0 to 100;


area threshold ranges from 0 to 100.
Motion Detect
Activation event: video storage, image snapshot, log, email function
and etc.
Backup
and
Record

Record Priority Manual >Video detect>Schedule

Storage
Support network storage status information
Management

Wire Network 1-channel wire Ethernet port, 10/100 Base-T Ethernet


Network

Wireless
IEEE802.11a/b/g/n, built-in antenna
Network
Standard HTTP, TCP/IP, ARP, IGMP, ICMP, RTSP, RTP,UDP, RTCP,
Network Protocol SMTP, FTP, DHCP, DNS, DDNS, PPPOE, UPNP, NTP, Bonjour,
SNMP.
Remote Monitor, system setup, file download, log information, maintenance ,
Operation upgrade and etc.

Access Protocol Support International, ONVIF


Interface
Aux

WPS WI-FI one key connection

Support
Restore Default
IR light IR distance 30m
Power DC12V
General Parameter

Power
4.9W MAX 7.3 W MAX
Consumption
Working
-30℃~+50℃
Temperature
Working
≤95%
Humidify
Dimensions(mm) 69*66*149
Weight 420g (excluding box)

7
Installation Installation with the bracket.

8
2 Framework
2.1 Cable
You can refer to the following figure for cable information. See Figure 2- and Figure 2-2.

Figure 2-1 Cable

Figure 2-2 Cable

9
Please refer to the following sheet for detailed information.
No. Port Function
Connection Note
Name
1 Ethernet Connect to standard Ethernet cable.
LAN Network port
port Note: Some devices do not support PoE.
2 DC Power input
/ Power port. Input DC 12V.
12V port
WPS/Hardware reset wire
Press the WPS button of router, keep the Reset wire short
circuit for 1-2 seconds, generally the device can be connected
WPS/Reset to corresponding router within 1 minute.
3 Reset /
port Keep the Reset wire short circuit for more than 5 seconds
when the device is under normal working condition, then the
system configuration information can be restored to default
setting.

2.2 Framework and Dimension


Please refer to the following figure for dimension information. The unit is mm. See Figure 2-3 to Figure
2-6.

Figure 2-3

10
Figure 2-4

Figure 2-5

11
Figure 2-6

12
3 Device Installation
Important
Please make sure the installation surface can min support the 3X weight of the camera and the
bracket.

Figure 3-1 Device installation 1

Please see Figure 3-1 and Figure 3-2.


Step 1
Stick installation sticker to designated surface where you will install the device (wall or ceiling).
Step 2
Dig a hole according to position of hole on installation sticker.
Step 3
Open accessories bag, take out expansion bolt and insert it into the hole you just dug.
Step 4
Open accessories bag, take out screw. Tighten the 4 screws to fix the device on the installation
surface (wall or ceiling). You can move device sunshade back and forth. When you have fixed the
device, you must tighten screws on sunshade.
Step 5
Plug external wiring of the device properly.

13
Figure 3-2 Device installation 2
Step 6
Use Philip’s head screw (in accessories bag) to loosen adjusting screw.
Step 7
Adjust the device in all possible directions, and set its monitoring direction.
Step 8
Use Philip’s head screw to tighten the screws.

14
4 Quick Configuration Tool
4.1 Overview
Quick configuration tool can search current IP address, modify IP address. At the same time, you can
use it to upgrade the device.
Please note the tool only applies to the IP addresses in the same segment.

4.2 Operation
Double click the “ConfigTools.exe” icon, you can see an interface is shown as in Figure 4-1.
In the device list interface, you can view device IP address, port number, subnet mask, default
gateway, MAC address and etc.

Figure 4-1 Search interface


Select one IP address and then right click mouse, you can see an interface is shown as in Figure 4-2.
Select the “Open Device Web” item; you can go to the corresponding web login interface.

Figure 4-2 Search interface 2

If you want to modify the device IP address without logging in the device web interface, you can go to
the configuration tool main interface to set.

15
In the configuration tool search interface (Figure 4-1), please select a device IP address and then
double click it to open the login interface. Or you can select an IP address and then click the Login
button to go to the login interface. See Figure 4-3.
In Figure 4-3, you can view device IP address, user name, password and port. Please modify the
corresponding information to login.
Please note the port information here shall be identical with the port value you set in TCP port in Web
Network interface. Otherwise, you cannot login the device.
If you are using device background upgrade port 3800 to login, other setups are all invalid.

Figure 4-3 Login prompt


After you logged in, the configuration tool main interface is shown as below. See Figure 4-4.

Figure 4-4 Main interface


For detailed information and operation instruction of the quick configuration tool, please refer
to the Quick Configuration Tool User’s Manual included in the resources CD.

16
5 Web Operation
This series network camera products support the Web access and management via PC.
Web includes several modules: Monitor channel preview, system configuration, alarm and etc.

5.1 Network Connection


Please follow the steps listed below for network connection.
 Make sure the network camera has connected to the network properly.
 Please set the IP address, subnet mask and gateway of the PC and the network camera
respectively. Network camera default IP address is 192.168.1.108. Subnet mask is 255.255.255.0.
Gateway is 192.168.1.1
 Use order ping ***.***.***.***(* network camera address) to check connection is OK or not.

5.2 Login and Main Interface


Open IE and input network camera address in the address bar. See Figure 5- 1.

Input your IP
address here

Figure 5- 1 IP address
The login interface is shown as below. See Figure 5- 2.
Please input your user name and password.
Default factory name is admin and password is admin.
Note: For security reasons, please modify your password after you first login.

17
Figure 5- 2 Web login
After you successfully logged in, please install WEB plug-in unit. Please refer to the Web Operation
Manual included in the resource CD for detailed operation instruction.
See Figure 5- 3.

Figure 5- 3 Web monitoring window

18
6 FAQ
Bug
I can not boot up Please click RESET button for at least five seconds to restore
the device or factory default setup.
operate properly.
The water leakage  The unauthorized front or rear cap remove many result in water
occurred. leakage.
 The glass front cap has sustained heavy push or strike.
 The waterproof plug of the rear cap becomes loosen.
IR video is poor.  Did not use the proper supplying power. The IR light can not
turn on completely.
 The object is out of the IR distance range of current device.
 IR-CUT does not turn to the night mode. The photosensitive
chip of the front-end can not sense the IR light.
I can not upgrade
When network upgrade operation failed, you can use port 3800 to
the device via
continue upgrade.
network.
I can not login the  For Windows OS 98 or Windows ME user, if you can not install
client-end or the the client-end or can not view after the installation. We
WEB. recommend the win2000 sp4 OS or higher, or install the client-
end of the low version.
 The Active X control is blocked.
 The display card version shall be dx8.1 or higher.
 Network connection error occurred.
 Invalid network setup.
 Invalid user name or password.
 Client version and device program do not match.
I can not play the  There is no player.
download file.  There is no DX8.1 or higher.
 For the MEDIA PLAYER, there shall be Div X503Bundle.exe
plug in if you play the .AVI file.
 For Windows XP user, you need to install the plug in
DivX503Bundle.exe and ffdsho-2004 1012.exe.
To guarantee After you modified the important setup, please reboot the device via
setup update the software to make sure the setup has been updated to the
storage medium.
Power adapter  The general power adapter can work ranging from 0℃ to 40 ℃.
The device may result in unstable power supply when the
temperature exceeds the working temperature.
 Please replace an industry-level power adapter if you are using
in the harsh environments.

19
Appendix Toxic or Hazardous Materials or Elements
Toxic or Hazardous Materials or Elements
Component
Name
Pb Hg Cd Cr VI PBB PBDE

Circuit Board
○ ○ ○ ○ ○ ○
Component

Device Case ○ ○ ○ ○ ○ ○

Wire and Cable ○ ○ ○ ○ ○ ○

Packing
○ ○ ○ ○ ○ ○
Components
Accessories ○ ○ ○ ○ ○ ○

O: Indicates that the concentration of the hazardous substance in all homogeneous materials in the
parts is below the relevant threshold of the SJ/T11363-2006 standard.

X: Indicates that the concentration of the hazardous substance of at least one of all homogeneous
materials in the parts is above the relevant threshold of the SJ/T11363-2006 standard. During the
environmental-friendly use period (EFUP) period, the toxic or hazardous substance or elements
contained in products will not leak or mutate so that the use of these (substances or elements) will not
result in any severe environmental pollution, any bodily injury or damage to any assets. The consumer
is not authorized to process such kind of substances or elements, please return to the corresponding
local authorities to process according to your local government statutes.

Note
 This user’s manual is for reference only. Slight difference may be found in user interface.
 All the designs and software here are subject to change without prior written notice.
 All trademarks and registered trademarks mentioned are the properties of their respective
owners.
 If there is any uncertainty or controversy, please refer to the final explanation of us.
 Please visit our website for more information.

Zhejiang Dahua Technology CO., LTD.


Address:No.1199 Bin’an Road, Binjiang District, Hangzhou, PRC.
Postcode: 310053
Tel: +86-571-87688883
Fax: +86-571-87688815
Email:[email protected]
Website: www.dahuatech.com

20

You might also like