0% found this document useful (0 votes)
516 views

IC Tester TSH 06F

The device has seven keys for navigation and operation. The Up and Down keys adjust settings, Left and Right keys move the cursor, and Enter key powers on/off and runs tests. It requires two AA batteries and powers on when Enter is held for two seconds, automatically displaying the voltage. Low battery will affect results and cause automatic shutdown. It has modes for different component types and automatically identifies certain components when placed in the holder.

Uploaded by

LaurentEunice
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
516 views

IC Tester TSH 06F

The device has seven keys for navigation and operation. The Up and Down keys adjust settings, Left and Right keys move the cursor, and Enter key powers on/off and runs tests. It requires two AA batteries and powers on when Enter is held for two seconds, automatically displaying the voltage. Low battery will affect results and cause automatic shutdown. It has modes for different component types and automatically identifies certain components when placed in the holder.

Uploaded by

LaurentEunice
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

Operating instructions

There are seven keys: Up Key, Down Key, Left Key, Right Key, Shortcut Key, Enter Key, P -key
and O- Key

Up and Down keys are used to adjust the directory and change the model number
Left and right keys are used to move around the cursor and select the item you want to change
Enter key is used to switch on/off and run the testing command
Open the battery covers, put in 2 AA batteries (1.5V), and then close the battery cover

Press the Enter key for more than 2 seconds to power on. When power on, the system displays the
current battery voltage automatically. When the battery power is low, please replace the batteries.
Low voltage will affect the reliability of the test results and the machine will automatically shut
down for protection.
How to switch on: press the Enter key for more than 2 seconds
How to switch off: 1. Press the Enter key in off directory, it will shut down immediately
2. Press the Enter button in any directory exceed 10 seconds then it will shut
down
3. After 60 seconds without any operation, it will shut down automatically
Shortcuts: O-key for fast shutdown
P-key is the backlit key

The following chart is for device


The bottom of the chip should align
Transistor should be in three slots which are on the bottom left
Optical coupling pin on the IC socket 13 pin (when measuring the saturable voltage drop)
Zener diode drop between 13 pin and 14 pin of the IC
Note: transistor shown corresponds to IC pin from left to right in the order of 10 pin, 11 pin, and 12
pin
Note: The order of pins shown by the transistor corresponding to 10 pin, 11pin, 12 pin of the IC
from left to right.

Directory Function

Auto mode Device searching, put the chip in the IC holder and the device type will be identified
Search 5.0 V mode automatically (identify automatically without input)
3.3 V mode Other directories are the automatic mode
74HC 74HC series logic devices testing (same with 74LS series, different driver circuit)
(enter the model manually)
74LS 74LS series logic devices testing (same with 74HC series, different driver circuit)
(enter the model manually)
CD 40 CD 4000 series logic devices testing (different from HEF40 series, the same driver
circuit) (enter the model manually)
HEF40 HEF4000 series logic devices testing (different from CD 40 series, the same drive
circuit) (enter the model manually)
45/145 45 series/ 145series logic devices testing (enter the model manually)
OTHER Interface driver device testing, such as: max232, max485, 75175, 75176, 75cll
(enter the model manually)
AMP Op-amp, comparer device testing, such as: LM324, LM358, LM339, LM393,
LM2902 (enter the model manually)
TR Transistor identification: identify the transistor type and the order of pins
automatically; identify the NPN, PNP, N-MOS, P-MOS, 1-SCR, 2-SCR, 2D
(identify automatically without input)
ZD Zener diode voltage regulator testing, testing range: 0V~5V, precision: 0.01V
(identify automatically without input)
LIGHT Optocoupler, such as: TLP521-1, PC817, PC923, 4n25, HCNW4506, BRT11\12\13,
HCPL-3101
OFF Switch off

You might also like