Fast Pyrolysis and Bio-Oil

Upgrading
Robert C. Brown
Iowa State University
and
Jennifer Holmgren
UOP
 Fast Pyrolysis
• Rapid thermal decomposition of organic
compounds in the absence of oxygen to
produce liquids, char, and gas
– Dry feedstock: <10%
– Small particles: <3 mm
– Short residence times: 0.5 - 2 s
– Moderate temperatures (400-500 oC)
– Rapid quenching at the end of the process
– Typical yields
Oil: 60 - 70%
Char: 12 -15%
Gas: 13 - 25%
 Source: Piskorz, J., et al. In Pyrolysis Oils White Poplar
Spruce
Bio-Oil
from Biomass, Soltes, E. J., Milne, T. A.,
Eds., ACS Symposium Series 376, 1988.
Moisture content, wt% 7.0 3.3
Particle size, µm (max) 1000 590
Pyrolysis liquid (bio-oil) Temperature 500 497
from flash pyrolysis is a Apparent residence time 0.65 0.48
low viscosity, dark-brown Product Yields, wt %, m.f.

fluid with up to 15 to 20% Water 11.6 12.2

Gas 7.8 10.8
water
Bio-char 12.2 7.7
Bio-oil 66.5 65.7
Bio-oil composition, wt %, m.f.
Saccharides 3.3 2.4
Anhydrosugars 6.5 6.8
Aldehydes 10.1 14.0
Furans 0.35 --
Ketones 1.24 1.4
Alcohols 2.0 1.2
Carboxylic acids 11.0 8.5
Water-Soluble – Total Above 34.5 34.3
Pyrolytic Lignin 20.6 16.2
Unaccounted fraction 11.4 15.2
 Multiple reaction pathways for
pyrolysis of cellulose

Depolymerization
Levoglucosan
Fast

Alkali-catalyzed
dehydration
Cellulose Hydroxyacetaldehyde
Slow
Char + water
 Fast Pyrolysis
• Advantages
– Operates at atmospheric pressure and modest
temperatures (450 C)
– Yields of bio-oil can exceed 70 wt-%
• Disadvantages
– High oxygen and water content of pyrolysis liquids
makes them inferior to conventional hydrocarbon
fuels
– Phase-separation and polymerization of the liquids
and corrosion of containers make storage of these
liquids difficult
 Several Kinds of Fast Pyrolysis
Reactors
• Bubbling fluidized bed
• Circulating fluidized beds/transport reactor
• Rotating cone pyrolyzer
• Ablative pyrolyzer
• Vacuum pyrolysis
• Auger reactor
 Bubbling Fluidized Bed
Gas, Char, and Oil
Vapors and Aerosol
• Heat supplied externally
to bed Freeboard
• Good mass & heat
transfer Biomass
• Requires small biomass
Fluid bed
particles (2-3 mm) Heat
Feeder

Distributor
plate
Fluidizing gas
Circulating Fluidized Bed/Transport
Reactor
Gas and Oil Vapors
• Hot sand circulated Pyrolyzer and Aerosol

between combustor Combustor

and pyrolyzer Flue
Gas
• Heat supplied from
Sand
burning char Biomass & char
• High throughputs
but more char Feeder Hot
Distributor
plate
attrition Sand

Air
Fluidizing gas
 Rotating Cone Pyrolyzer
Vapors and
• Sand and biomass Biomass
Aerosol
Hot Sand
brought into contact
within rotating cone
• Compact design and
does not need carrier
gas
• Requires very small
biomass particles and Rotation
is hard to scale-up
 Ablative Pyrolyzer
• High pressure of particle
on hot reactor wall Spinning
achieved by centrifugal Disk

or mechanical motion
Pressure
• Can use large particles Applied
and does not require to Wood Bio-oil
Liquid
carrier gas Released
from Wood
• Complex and does not
scale well
 Vacuum Pyrolysis

• Biomass moved by Scrapper

gravity and rotating Driver Biomass
scrappers through
multiple hearth
pyrolyzer with
temperature increasing
from 200 C to 400 C
• Can use larger
particles and employs
little carrier gas
Char
• Expensive vacuum
pump and difficult to
scale-up
Multiple hearth Condensers Vacuum
vacuum pyrolysis pump
reactor
 Auger Reactor

Biomass Hot
• Hot sand and sand
biomass mixed by
auger Vapors &
aerosol to
• Suitable for small condenser
scale
• Requires hot sand
heating and Char &
circulation system sand
Auger Auger
driver reactor
 Relative Merits of Various Reactors

Property Status Bio- Comp- Feed Inert Specific Scale

oil lexity size gas size up
wt% need
Fluid bed Demo 75 Medium Small High Medium Easy
CFB Pilot 75 High Medium High Large Easy

Entrained None 65 High Small High Large Easy

Rotating Pilot 65 High V small Low Small Hard
cone
Ablative Lab 75 High Large Low Small Hard
Auger Lab 65 Low Small Low Medium Easy
Vacuum Demo 60 High Large Low Large Hard
The darker the cell color, the less Lab: 1 – 20 kg h-1
desirable the process. Pilot: 20 – 200 kg h-1
Demo: 200 – 2000 kg h-1
Adapted from PYNE IEA Bioenergy http://www.pyne.co.uk
 Which will dominate?
TECHNOLOGY STRENGTH
Strong Average Weak

Ablative
MARKET ATTRACTIVENESS

High Cyclonic

Rotating cone

Entrained flow

Fluid bed

Circulating fluid bed

Low and transport reactor

Auger

Adapted from PYNE IEA Bioenergy http://www.pyne.co.uk

 Fast Pyrolysis System
Lignocellulosic
Pyrolysis
feedstock
gases
Vapor,
Mill Flue gas, char Cyclone
gas Quencher
products

Hopper
Pyrolysis
Char
reactor
Motor Feeder Bio-oil Bio-oil
storage
Fluidizing Combustor
gas

Air
 Scale
Diesel Output (million US gallons/yr)
0 50 100 150 200 250
$8,000
Small gasification (multiple units 110,000
Capital Cost (million 2005 US dollars)

$7,000 US ton/yr) + small FT multiple units

Small pyrolysis (multiple units 110,000
US ton/yr) + large FT
$6,000 Large gasification + large FT

$5,000

$4,000
$400,000 pbpd
$3,000

$2,000

$1,000
$100,000 pbpd
$0
0.0 1.0 2.0 3.0 4.0 5.0
Biomass Input (million US tons/yr)
Adapted from: Bridgwater, ACS Meeting, Washington, D.C., 2005
 Suitable Feedstocks
• Wide variety of feedstocks can be used
• Fibrous biomass usually employed
• Wood higher yielding than herbaceous
biomass
 Storage & Transportation
• Distributed preprocessing allows transport
and storage as liquid
• High acidity requires storage in stainless
steel or plastic
• Stability problems need to be solved
Post Processing to Motor Fuels
• Direct application of bio-oil
• Hydrocracking of bio-oil
• Gasification of bio-oil
• Fermentation of Bio-oil
 Bio-Oil Burned in Diesel Engines

• Bio-oil used as directly as diesel fuel substitute

• Only suitable for stationary power applications

Bio-oil vapor
Cyclone
Bio-Oil
Stationary
Char Recovery
Diesel Engine
Pyrolyzer

Bio-Oil
Fibrous
biomass
Bio-Oil
Storage
 Bio-Oil Hydrocracking
• Directly converts biomass into liquid bio-oil (lignin,
carbohydrate derivatives, and water) and char
• Bio-oil catalytically converted into hydrocarbon fuel
(green diesel) Green
diesel

Bio-oil vapor
Cyclone

Hydrocracker
Steam Hydrogen
Bio-Oil
Char Recovery Reformer

Carbohydrate derived
Pyrolyzer

Phase aqueous phase

Fibrous Separation
biomass
Lignin
 Bio-Oil Gasification
• Bio-oil and char slurried together to recover 90% of
the original biomass energy
• Slurry transported to central processing site where it is
gasified in an entrained flow gasifier to syngas
• Syngas is catalytic processed into green diesel (F-T
liquids)
Bio-oil vapor
Cyclone

Entrained Flow

Fischer Tropsch
Bio-Oil

Gasifier

Reactor
Recovery
Pyrolyzer

Bio-Oil
Fibrous Pump
biomass
Slurry
Char Preparation
Slag Green
Diesel
 Bio-Oil Fermentation
Fiber Distillation

Ethanol
Pentose
Hot water
extraction

Fermenter
Fiber byproduct

Bio-oil vapor Water

Cyclone

Bio-Oil
Char Detoxification
Recovery

Fermenter
Pyrolyzer

Phase
Separation Anhydrosugar &
other carbohydrate
Lignin
 Energy Efficiency

• Conversion to 75 wt-% bio-oil translates to

energy efficiency of 70%
• If carbon used for energy source (process
heat or slurried with liquid) then efficiency
approaches 94%

Source: http://www.ensyn.com/info/23102000.htm
 Co-Products
• Gas (CO, H2, light
hydrocarbons)
– Can be used to heat
pyrolysis reactor
• Char: Several potential
applications
– Process heat
– Activated carbon
– Soil amendment
Potential Co-Products from Bio-Oil
Products of pyrolysis for several different pretreatments of cornstover (Brown et al. 2001)

No Acid Acid Wash Acid Wash

Pretreatment Hydrolysis with catalyst
Products (Wt% maf)
Char 15.8 13.2 13.2 15.9
Water 2.57 10.6 10.4 7.96
Organics 59.1 67.2 68.5 67.7
Gases 22.6 9.02 7.88 8.44
Organics (Wt %)
Cellobiosan trace 4.55 3.34 4.97
Levoglucosan 2.75 17.69 20.12 23.10
Hydroxy-acetaldehyde 11.57 5.97 3.73 3.93
Formic acid 2.61 Trace Trace 0.73
Acetic acid 3.40 1.51 1.26 0.40
Acetol 4.53 trace trace trace
Formaldehyde 2.75 1.63 trace 0.70
Pyrolytic lignin 33.40 16.89 17.74 20.08
 Quality Assurance
• Bio-oil quality issues:
– Moisture content
– Particulate content
– Sulfur and nitrogen content
– Stability
 Equipment Maintenance
• Potential problems with pyrolysis
equipment
– Bed agglomeration
– Clogging of condensers
– ESP performance
• Catalytic reactors
– Poisoning by sulfur and chlorine
– Coking
 Waste Streams
• Main products (gas, char, bio-oil) account
for all mass of biomass feedstock
 Technical Barriers
• Preparing dry, finely divided biomass
particles
• Maintaining high bio-oil yields
• Improving bio-oil stability
• Determining optimal scale of facility
 Alternative Fuels: Targets
WTW Energy /GHG Emissions Clusters
400 „ Alternative fuels may need to target:
Hydrogen – < 100 gm CO2/km WTW
350 from coal, FC
GHG, CO2 Equivalent, gm/km

DME from NG – GTL, DME from gas – close, but

300 GTL from NG not there yet
FAME
250 Conventional „ Several other alternatives in study
EtOH (not shown for simplicity)
200 Hydrogen from
Gasoline & Diesel bio, ICE „ Engine manufacturers developing
150
more efficient advanced ICE’s in
100 Green Diesel addition to hybrids and FC’s
50
– Variable DI gasoline
– “Part Homogeneous” diesel
0 combustion
0 200 400 600 800 1000
Energy, MJ/km – “Combined Combustion” systems
Source: CONCAWE / EU CAR / – Improve fuel efficiency
EU Comm’n, Dec 2003

Gasoline & Diesel in Advanced ICE’s Set Tough Targets!

 Biorenewables and Petroleum
Feeds: Relative Availability
Global US
50 14
Liquid Transport Fuels Liquid Transport Fuels
Diesel 12 Gasoline
Available Oil/Grease Diesel
40
Cellulosic Waste 10 Available Oil/Grease
Cellulosic Waste

MBPD
MBPD

30 8

6
20
4
10
2

0 0
Current Potential Current Potential

Available Cellulosic Biomass Could Make a

Significant Impact in Fuels Pool
UOP 4434A-09
 Py Oil Portfolio

Gasoline
Solid
Pyrolysis Oil/
Cellulosic
Lignin Hydrogen/
Biomass
Power Generation

Diesel
Lignin Molecular Structure
 Treating Technologies
Hydrotreating
• Hydrotreating is the key process
to meet quality specifications for
refinery fuel products
• Removes sulfur, nitrogen, olefins,
and metals using hydrogen
• Hydrogen addition also improves
the quality of distillate fuels (poly
aromatics, cetane, smoke point)
• Treating feedstocks for other
processing units
 Conversion Technologies
Hydrocracking
• Hydrocracking upgrades heavy
feeds including gas oils and
cycle oils into lighter, higher
value, low sulfur products
• High pressure is used to add
hydrogen and produce
premium distillate products
• Naphtha products normally are
low octane and are upgraded
in a reformer
• Product volume is 10-20%
higher than the feedstock
 Hydrocracking Catalyst Portfolio
New Generation
HC-215 Current Generation
Distillates Selectivity

HC-115
DHC-8 Flexible Max
Naphtha
DHC-32
HC-150
DHC-39
DHC -41
DHC-41 HC-170
HC-43 HC-29 HC-190
Max HC-33
Diesel Distillates HC-26
HC-24 HC-34

Activity

Distillate Selectivity Decreases with Increasing Activity

YE for Hydrocracking Pyrolysis Oil

Feed Wt% bpd

Pyrolysis Oil 100 2,250
H2 4-5
Products
Lt ends 15
Gasoline 30 1,010
Diesel 8 250
Water, CO2 51-52
 Gasoline Production from Py Oil
($40/bbl crude)
Feed $/D bpd
Pyrolysis Oil 40,500 2,250
H2 25,680 21.4 T
Products
Lt Hydrocarbons 19,303 64T/D
Gasoline 52,520 1,010
Diesel 12,000 250
Utilities -4,800
Net 12,843

$ 4.2 million/year
 Hydroprocessing costs:
Effect of Scale
HDT Capital Cost vs Capacity
Cost/
1000 $35.0
Unit size Cost, bpd Capital Cost, $MM (2006)
(bpd) $MM $MM $30.0
30000 $28.9 $ 0.96
$25.0
27500 $27.4 $ 1.00
25000 $25.9 $ 1.04 $20.0
22500 $24.3 $ 1.08
20000 $22.7 $ 1.13 $15.0
17500 $20.9 $ 1.19 $10.0
15000 $19.1 $ 1.27
12500 $17.1 $ 1.37 $5.0
10000 $14.9 $ 1.49
7500 $12.6 $ 1.68 $0.0
5000 $9.9 $ 1.97 0 5000 10000 15000 20000 25000 30000 35000
2500 $6.5 $ 2.60
Capacity, BPD
 Size of Hydroprocessing Units
2000 bpd HC units
2500 bbl/day
38.3 M gal/year pyrolysis oil processed
Dynamotive’s Planned 174072 tonnes/yr pyrolysis oil processed
200 tpd Plant 65%
267803 tonnes/yr
Conv. to biooil
biomass
Dynamotive's 200 tonne/day facility (planned production) 734 tonne/day plant
200 tonne/day biomass processed
200000 kg/day
% conversion
biomass to pyrolysis
65% oil 30,000 bpd HC unit
130000 kg/day biooil
1.2 kg/liter density of pyrolysis oil (typical refinery size)
108333 liter/day
30000 bbl/day
28622 gal/day
459.9 M gal/year pyrolysis oil processed
681 bbl/day Hydroprocessing unit
2088866 tonnes/yr pyrolysis oil processed
65% Conv. to biooil
3213640 tonnes/yr biomass
8804 tonne/day plant
 Example:
Potential from logging residues
41 Million dry tons logging residue available (Billion ton annual study)
10% % water of biomass for pyrolysis unit
46 Million tons of logging residue feed
65% % conversion to pyrolysis oil
29.6 million tons of pyrolysis oil
6519 M gallons of pyrolysis oil from logging residue
425271 bbl/day

„ ~14 30,000 bpd hydroprocessing units

– Estimated cost: $405 MM
„ ~170 2500 bpd hydroprocessing units
– Estimated cost: $1105 MM
Distributed Pyrolysis Plants; Centralized Refining

DME Integrated into traditional

P P Biomass
natural gas conversion
Methanol
process or refinery
Gasifier

P P Gasification
H2
Synthesis Gas
Reforming
P P

Natural Gas GTL, BTL

„ Key Decision: What are we planning to

transport?
 Technical Barriers

„ Securing a consistent py Oil feedstock

„ Logistics
„ Balance of distributed vs. centralized
„ Catalyst and process
invention/development/commercialization
 Summary
„ Vegetable oils, grease and pyrolysis oil could be
feasible feedstocks for conventional petroleum
refineries
– Other feedstocks and processing options also look
promising
– Increased volumes of biobased feedstocks required
• Consistent source of pyrolysis oil or other lignocellulosic
biomass
„ Biorenewable processing options identified are
not limited to refinery integration
– Stand alone units possible
• Biorefineries; Biofeedstock source
• Portable H2

UOP 4434A-36
 Acknowledgements
DOE, Project DE-FG36-05GO15085

Contributors Contributors
„ MTU „ PNNL
– David Shonnard – Doug Elliott
„ NREL – Don Stevens
– Stefan Czernik „ UOP
– Richard Bain – Tom Kalnes
– Terry Marker
– Dave Mackowiak
– Mike McCall
– John Petri
Project Manager: Rich Marinangeli