CEMTEC R88

MULTIPURPOSE EPOXY PUTTY

Note
DESCRIPTION
Even with proper procedures, an acid etched
CEMTEC R88 is a high strength, non-slumping, two surface may not provide a bond as strong as a
component epoxy putty. This system is tough and mechanically prepared surface. Mix part A and
resilient when compared to concrete. It has excellent part B (resin & hardener) for 3 minutes using a
properties that make it suitable to be put in several drill and mixing prop. For ease of mixing, add the
uses as a bedding system, adhesive or a repair part B to part A (not the reverse). The epoxy must
material be well mixed to ensure proper chemical reac-
tion.
FEATURES/BENEFITS
Forms high strength, non-slump, non-shrink, Fill routed out cracks and cut joints with CEMTEC
epoxy bedding system. R88 , then apply CEMTEC R88 over the rest of
Forms a stiff but easily workable compound. the floor. Trowel CEMTEC R88 to the required
level using the minimum of solvent on the trowel
Resistant to impact and a wide range of
to aid workability. The surface must be finished
corrosive chemicals.
smooth by use of a paint brush dipped in
Has strong adhesion to concrete. CEMTEC SOLVENT.
Can be used for wide range of applications like bedding, SPECIFICATIONS/COMPLIANCES
grouting, crack filling and repair of surface defects in The epoxy bedding system CEMTEC R88 complies
horizontal, vertical and overhead applications. with ASTM C 881 Type 1, Grade 3 Classes B & C.
PRIMARY APPLICATIONS TECHNICAL INFORMATION
Crack repairs in decks and concrete slabs. Typical Engineering Data
The following information was developed under
General Adhesive for various materials over laboratory conditions.
concrete and steel. Compressive
Anchoring epoxy for reinforcement steel bars Strength : 55N/mm2 (ASTM C-579)
and anchor bolts. Bond strength : Greater than that of the concrete
Adhesive for injection nipples or surface packers. Pot-life : @25°C : 1hour 30 minutes
@40°C : 45 minutes
Sealing dry cracks and gaps around pipes Tack free time : @25°C : 8 hours
Crack and pinhole repairs before epoxy coatings @40°C : 2 hours 30 minutes
in tanks and concrete slabs. Full cure : @25°C : 7 days
@40°C : 3 days
DIRECTIONS FOR USE CHEMICAL RESISTANCE
New concrete should have cured until the shrinkage Tartaric acid 10% Excellent
and moisture movement is low, and possesses a Hydrochloric acid 10% Excellent
porous and textured surface with all curing compounds Sodium hydroxide 10% Excellent
and sealers removed. Old concrete must be clean and Diesel fuel/petrol Excellent
well textured. All oil, dirt, debris, paint and unsound Sulphur acid 10% Good
concrete must be removed. The surface must be Sugar solutions 10% Excellent
prepared mechanically using a scabler, bush hammer, Lactic acid 10% Excellent
shot blast or scarifier which will give a surface profile of Hydrocarbons 10% Excellent
a minimum (3 mm) and expose the large aggregate of Phosphoric acid 10% Good
the concrete. The final step in cleaning should be the Seawater Excellent
complete removal of all residues with a vacuum clean- Sewerage Excellent
er or pressure washing. Acid etching is acceptable only Mineral, vegetable animal oils & fats Excellent
when Mechanical preparation is impractical. It is Ammonia Excellent
recommended only contractors experienced in the acid Formaldehyde Excellent
etching process use this means of the surface prepara- Nitric acid 10% Good
Scan Here For Download
Data Sheet tion. The salts of the reaction must be thoroughly Acetic acid 5% Limited
pressure washed away. Allow the concrete to dry
completely.

YIELD 3 kg kits will yield approxmately 1.75 liters, 50 kg kits will yield approxmately 29.17 liters.

PACKAGING 3 kg and 50 kg kit.

COLOR Available in Grey.
CLEAN-UP Clean all tools and equipment with
CEMTEC SOLVENT. Do not allow material to
harden on the equipment.

SHELF LIFE
Two years in unopened container.

HEALTH & SAFETY

Epoxy components may cause irritation.
Avoid contact with eyes and skin.
Store under cover out of direct sunlight and
protect from extremes of temperature.
Solvents are Flammable. Keep away from
heat, sparks, open flame, or lighted
cigarettes. Use explosion-proof application
equipment.

TD/118/F

Scan Here For Download

Data Sheet
Quality Statement
CMCI manufactures its products at their manufacturing facility in
Saudi Arabia as per the Quailty Procedures centified to conform
with quality Management System described in ISO 9000 series
"High Quality Construction Chemicals"
CMCI provides a comprehensive technical support system for its full
CONSTRUCTION MATERIAL CHEMICAL INDUSTRIES
range of high erformance construction products CMCI also offers P.O. Box 7137, Dammam 31462, Saudi Arabia,
full technical field support to consultants, Architects, contractors, Tel: 00966-13-8471450; Fax: 00966-13-8471575
applicators and End Users. Email: [email protected], Web: www.cmci-sa.com
The Technical Specification infromation and recommendations given are based on the current technical knowledge and the user or his representative is
recommended to check the suitability of the product CMCI reserves the right to amend the technical characteristic of theproduct as part of ongoing research
and development. As the work execution is beyond the direct and continuous control of CMCI no guaranty and or responsibility is assumed on the
performance of work completion executed with use of our products.