ORIFICE PLATE & FLANGE

Orifice
Tapping of differential pressure is done by this vener contractor tap
Orifice. Since Orifice plate can be installed directly to flange of pipe,
flow measurement by this Orifice plate can be performed more
economically than by orifice plates with rings, and it is generally
suited for large diameter pipes. As for large diameter pipes of
500mm or greater, these Orifice plates are used to measure the
average value of pressure by making some differential pressure
tapping holes around the pipe and connecting thereto a loop form
pressure equalizing pipe.

DAEHAN Paddle-Type Orifice Plates are used with Orifice Flange

Unions.All outer diameters of the plates are machined, providing a
uniformlycircular disc. This results in a high degree of concentricity of
the Orifice boreand the plate outer diameter. Next, handles are carefully
welded on. Theplates are then sanded in special machines to a
prescribed finish. Bankplates and plates with popular bore size are
stocked continuously. Eachplate is stamped on its handle with line
size, flange rating, Orifice bore andplate material. DAEHAN maintains a
stock in Type 304 and 316 StainlessSteel in standard thickness. Other
size and materials are available onrequest.

Diameters of holes in paddle Plate Handles are as flows:

Plate Size Hole Diameter
1/2”thru 2” 1/4”
11/2” thru 12” 3/8”
14” thru 24” 1/2”
26” and larger 3/4”

The bore and bevel is the standard of limiting the plate edge thickness.
Thebevel is machined on a 45 angle to the desired edge thickness.
Unlessotherwise specified, plates will be bevelled to 1/50 of the line
I.D. or 1/8of the Orifice bore, minimum governing.
ORIFICE PLATE & FLANGE

Eccentrically bored plates are plates with the Orifice offcenter,or

eccentric, as opposed to concentric. The bore of theeccentric Orifice
normally is inscribed in a circle with is 98%of the pipe diameter, so
that solids or slurries may passthrough, Eccentric Orifice plates are
used in many industriesincluding heavy and light chemicals, steel,
paper, atomic andpetrochemicals.

Segmentally bore Orifice plates are provided formeasurements where

solides are entrained in a gas or liquidflow stream. The circular portion
of the bore is inscribedwithin a circle which is normally 98% of the
pipe diameter.The segmental opening may be placed either at the top
orbottom of the pipe. Industries using these bores includesewage
treatment, steel, chemical, water conditioning, paper,and
petrochemical.

How DAEHAN Orifice Flanges Provide Better Measurement Orifice

flanges one of the most economical means ofmeasuring flow, and
DAEHAN Orifice Flanges are speciallymanufactured to be the most
accurate. Automatic machinetools enable DAEHAN to meet the most
stringent tolerancesand recommendations for flanges, with careful
attentiongiven to tap location, bore smoothness, bolt and
flangefacings. DAEHAN Orifice Flanges are made of forged steel,
A.S.T.M. A-105. Other materials are available on specialorder and
extended delivery.
ORIFICE PLATE & FLANGE
Orifice Plate & Flange Assembly

ORIFICE BORE TYPE ORIFICE FLANGE TYPE

- Concentric Square Edge Type - Weld Neck Type
- Eccentric Type - Socket Weld Type
- Segmental Type - Slip On Type
- Quadrant Edge Type
NOMINAL DIAMETERS
FLOW CALCULATION STANDARDS - 25mm(1inch) to 3000mm(120inch)
- ISO5167, JIS Z 8762, ASME, KS A 0612
TAPS TYPE
FLANGE RATING - Flange Taps Type
- ANSI 150, 300, KS, JIS 10K 20K, AWWA. - Corner Taps Type
- D-D/2 Taps Type
MATERIAL
- 304SS, 304L SS, 316SS, 316L SS, Monel, MATERIAL
- Hastelloy, Inconel, Cu-Ni, PTFE, Glass - A105, A182 F304, A182 F316, A182F11, A182
- Ni, Cr, Mo Alloy Steel(A182 F11 to 91) F22, A182 F51, A350 LF2, etc
ORIFICE PLATE & FLANGE
MODELS SUFFIX CODES DESCRIPTION

Orifice Plate DHOP -------------------------------------------------------------------- Plate Only

& Flange
Flange Assembly
Assembly DHOF-W ---------------------------------------------------------------- (Bolt, Nut, Gasket Include)

D ---------------------------------------------------------------- D-D/2 Taps

Tap Type F ---------------------------------------------------------------- Flange Taps

C ---------------------------------------------------------------- Corner Taps

Nominal Pipe Size ----------------------------------------- Pipe size in inch or mm

CS ------------------------------------ Carbon Steel

4S ------------------------------------ 304SS

4L ------------------------------------ 304L SS

6S ------------------------------------ 316SS

6L ------------------------------------ 316L SS
Material : Plate/Flange
11 ------------------------------------ A182 F11

12 ------------------------------------ A182 F12

51 ------------------------------------ A182 F51

91 ------------------------------------ A182 F91

OP ------------------------------------ Option

015 ----------------------- ASME(ANSI) Class 150 LB

030 ----------------------- ASME(ANSI) Class 300 LB

Mounting Connection 010 ----------------------- KS(JIS) Class 10K

020 ----------------------- KS(JIS) Class 20K

000 ----------------------- Option

1 ----------------- NPT 1/2

2 ----------------- NPT 3/4

Diff' Taps
3 ----------------- SW 1/2

4 ----------------- SW 3/4

N ------- None
Meter Run
Y ------- Include

Option
RING TYPE ORIFICE

DESCRIPTIONS
Orifice Ring Assemblies are used for flow measurement of smaller or medium sized pipes at lower pressures
Each assembly consists of one orifice plate and two orifice rings, Differential pressures are taken out in a corner
tap system.
Orifice Blocks, which are of a unit-construction type and provide higher pressure ratings than the Orifice Ring
Assemblied, also are abvailable. Differential pressures are taken out in a corner tap system.

SPECIFICATIONS
ORIFICE BORE TYPE : MATERIALS
- Concentric Square Edged Orifices - Ring and Pressure Tap Nipple : C.S, 304SS, 316SS
- Quadrant Edged Orifices. - Plate : 304SS, 316SS, 316L, Monel, other
- Minimum quadrant edged orifice diameter 4.5mm -Tab Handle : 304SS, 316SS
- Minimum quadrant edged radius 0.5mm
TAP CONNECTION
FLOW CALCULATION STANDARDS : - PT 1/2 or 1/2 NPT male,
- ISO5167, JIS Z 8762, ASME, KS A 0612 - Socket weld, butt weld or flange.(Flange rating to be
the same as the of the process pipeline)
FLANGE RATING
- JIS5, 10, 20, 30kg/cm2 ANSI 150#, 300# GASKET:
Material : Asbestos, Non-Asbestos, Teflon
Thickness :1.5mm,2.0mm,3.0mm
RING TYPE ORIFICE
MODELS SUFFIX CODES DESCRIPTION
Ring Type
Orifice DHOF-RING ----------------------------------------------------------- Coner Taps Plate & Ring

F ---------------------------------------------------------------- Flange Include

Flange
N ---------------------------------------------------------------- Flange Exclude

Nominal Pipe Size ----------------------------------------- Pipe size in inch or mm

CS ------------------------------------ Carbon Steel

4S ------------------------------------ 304SS

4L ------------------------------------ 304L SS

6S ------------------------------------ 316SS

6L ------------------------------------ 316L SS
Material : Plate/Flange
11 ------------------------------------ A182 F11

12 ------------------------------------ A182 F12

51 ------------------------------------ A182 F51

91 ------------------------------------ A182 F91

OP ------------------------------------ Option

015 ----------------------- ASME(ANSI) Class 150 LB

030 ----------------------- ASME(ANSI) Class 300 LB

Mounting Connection 010 ----------------------- KS(JIS) Class 10K

020 ----------------------- KS(JIS) Class 20K

000 ----------------------- Option

1 ----------------- NPT 1/2

2 ----------------- NPT 3/4

Diff' Taps 3 ----------------- SW 1/2

4 ----------------- SW 3/4

0 ----------------- Option

B ------- Ball Valve

G ------- Glove Valve

Taps Valve
N ------- None

O ------- Option

Option
HIGH PRESSURE ORIFICE

DESCRIPTION
These flanges include both the welding neck type used
with orifice plates or orifice plates with rings.
They are available in the following types

Model DHOF-RTJ
Used with Model DHOF-RTJ orifice with holding ring
for flange taps. Available only in welding neck type.
Flange faces are ring-joint types

SPECIFICATIONS
- Welding neck. Type DHOF-RTJF - Two per flange. Provided in Model DHOF-RTJF
are only available with welding neck style. the flange tap location specified in ISO5167O

NOMINAL PIPE SIZE CONNECTIONS

- 1-1/2B to 24B(40A to 600A) - 1, For threading directly to flange 1/2NPT F
3/4NPT F, 1/2 S.W, 3/4 S.W
FLOW CALCULATION STANDARDS
- 2, For connecting with nipple 1/2NPT M,
- ISO5167, JIS Z 8762, ASME, KS A 0612
3/4NPT M, socket weld, butt weld or flange
FLANGE RATING
BOLTS & NUTS
- ANSI 600, 900, 1500, 2500LB RTJ Oval Type
- 1,Bolt Type & Material : Stud & A193 Gr B7
or Octagonal Type
- 2,Nut Type & Material : Hex * A194 2H
MATERIAL
- Carbon Steel
- 304SS, 304L SS, 316SS, 316L SS
- Ni, Cr, Mo Alloy Steel(A182 F11 to 91)
HIGH PRESSURE ORIFICE

MODEL SUFFIX CODES DESCRIPTION

P ------------------------------------------------------------------------- Plate Only

DHOF-RTJ
F ------------------------------------------------------------------------- Flange Include

Nominal
Pipe ------------------------------------------------ Pipe size in inch or mm
Size

CS ------------------------------------ Carbon Steel

4S ------------------------------------ 304SS

4L ------------------------------------ 304L SS

6S ------------------------------------ 316SS

6L ------------------------------------ 316L SS
Material
11 ------------------------------------ A182 F11

12 ------------------------------------ A182 F12

51 ------------------------------------ A182 F51

91 ------------------------------------ A182 F91

OP ------------------------------------ Option

060 ------------------------- ANSI Class 600 LB

090 ------------------------- ANSI Class 900 LB

Mounting Connection 150 ------------------------- ANSI Class 1500 LB

250 ------------------------- ANSI Class 2500 LB

000 ------------------------- Option

1 ------------------ NPT 1/2

2 ------------------ NPT 3/4

Diff' Taps
3 ------------------ SW 1/2

4 ------------------ SW 3/4

Option
HIGH ACCURACY ORIFICE

DESCRIPTION
These flanges & meter run tube, flow straightener Include high accuracy Orifice Assembly
They are available in the following types

Model : DHOF-H
Used with Model DHOF-H orifice plate with weld neck flange, meter run tube, flow straightener, etc

L (17Di)
(12Di) (5Di)
(10Di)

SPECIFICATIONS
Meter run tube type
DHOF-H are only Assembly

Accuracy Flange Material

- 1B to 20B(40A
1-1/2B to 500A)
to 20B(40A : 0.25%
to 500A) : 0.25% - Carbon steel
- 22B to 32B(550A to 800A) : 0.3%
0.3% - 304(L)SS, 316(L)SS
- Ni, Cr, Mo Alloy steel(A182 F11 to 91)
Nominal pipe size
-- 1B to 32B(25A
1-1/2 to 800A)
to 32B(40A to 800A) Plate Material
- 304(L)SS, 316(L)SS
Flange Rating - Ni, Cr, Mo Alloy steel(A182 F11 to 91)
- ASME(ANSI) 300#, 600#, 900# - Inconel, Hastelloy, Monel etc
- Standard : ASME B 16.36
Meter run tube
Flow Calculation standard - A106
- ISO5167-2003 - 304(L)SS, 316(L)SS
- ASME PTC - Ni, Cr, Mo Alloy steel(A335 F11 to 91)
- AGA3
- JIS Z 8762 Connection
- KS A 0612 - 1. For threading directly to flange 1/2NPTF 3/4NPTF,
1/2SW, 3/4SW
- 2. For connecting with nipple 1/2NPTM, 3/4NPTM,
socket weld, butt weld or flange
HIGH ACCURACY ORIFICE

MODEL SUFFIX CODES DESCRIPTION

DHOF-H
Pipe size in inch or mm
Nominal Pipe Size
30 300#
60 600#
Flange Rating
90 900#
O1 Option
4(L)S 304(L)SS
6(L)S 316(L)SS
Plate Material I6 Inconel 600
HS Hastelloy-C 276
O2 Option
CS Carbon Steel
4S 304(L)SS
6S 316(L)SS
11 A182 F11
Flange Material 12 A182 F12
22 A182 F22
51 A182 F51
91 A182 F91
O3 Option
CS Carbon Steel
4S 304(L)SS
6S 316(L)SS
11 A335 P11
Meter run tube Material 12 A335 P12
22 A335 P22
51 A335 P51
91 A335 P91
O4 Option
0 MFR STD
1 NPT 1/2
2 NPT 3/4
Diff' Pressure Taps
3 SW 1/2
4 SW 3/4
O5 Option
T Tube Bundle
E Etoile
A AMCA
Flow Straightener
K K-Lab
N NEL
O6 Option
O One Body
Transmitte S Separation Type
O7 Option
A 4 ~ 20mA
Output V 1 ~ 5V
R etc
Option
ORIFICE TYPE (INSTALLATION
& PIPING REQUIREMENTS)

Piping Requirements for Orifices, Flow Nozzels and Venturi Tubes

RESTRICTION ORIFICE

DESCRIPTIONS
The restriction orifices are used for reducing fluid pressure and are designed somewhat different the orifice
plates that are used for meassuring flow rates.
There are some types of restriction orifices, including a single plate with a single hole, a single perforated
plate(having diffused holes), and a set of welded multi orifices (a multistage orifice) which are used for
high-pressure high-temperature fluids.
The bore edge of the restriction orifices can be surface-hardened with stellite welding or by nitrification.

SPECIFICATIONS
MOUNTING
- Flange, Union, Butt Weld etc

NOMINAL PIPE SIZE

- 1/2B to 24B(15A to 600A)

FLOW CALCULATION STANDARDS

- ISO5167, JIS Z 8762, ASME, KS A 0612

FLANGE RATING
- ANSI 150, 300, 600, 900, 1500, 2500LB RTJ
Oval Type or Octagonal Type

MATERIAL
- Carbon Steel
- 304SS, 304L SS, 316SS, 316L SS
- Ni, Cr, Mo Alloy Steel(A182 F11 to 91)
- Monel, Hastelloy, Inconel etc
RESTRICTION ORIFICE
MODELS SUFFIX CODES DESCRIPTION

DHRO-SH ------------------------------------------------------------- Single Hole

Restriction
DHRO-MH ------------------------------------------------------------- Multi Hole
Orifice
DHRO-MS ------------------------------------------------------------- Multi Stage

F ---------------------------------------------------------------- Flange Include

Type
N ---------------------------------------------------------------- Flange Exclude

Nominal Pipe Size ----------------------------------------- Pipe size in inch or mm

CS ------------------------------------ Carbon Steel

4S ------------------------------------ 304SS

4L ------------------------------------ 304L SS

6S ------------------------------------ 316SS

6L ------------------------------------ 316L SS

11 ------------------------------------ A182 F11

Material : Plate/Flange
22 ------------------------------------ A182 F22

51 ------------------------------------ A182 F51

91 ------------------------------------ A182 F91

I 5 ------------------------------------ Inconel 625

M0 ------------------------------------ Monel 400

HC ------------------------------------ Hastelloy-C276

OP ------------------------------------ Option

015 ----------------------- ASME(ANSI) Class 150 LB

030 ----------------------- ASME(ANSI) Class 300 LB

060 ----------------------- ASME(ANSI) Class 600 LB

Mounting Connection 090 ----------------------- ASME(ANSI) Class 900 LB

150 ----------------------- ASME(ANSI) Class 1500 LB

250 ----------------------- ASME(ANSI) Class 2500 LB

000 ----------------------- Option

Option
 INTEGRAL ORIFICE
DESCRIPTION

Integral Orifice the One-Piece DP Flow Meter

Integral Orifice is an orifice-based flow meter with a difference
- Its advanced design greatly simplifies installation and commissioning

Integral Orifice is a stand-alone, orifice-based flow meter that incorporates all the following
features:
- Integral 3-valve manifold
- Integral connections between the carrier tappings and manifold
- DP transmitter, factory-mounted onto the manifold and pre-configured for the application
- Fully leak-tested and configured

DISTINCTIVE

Integral Orifice is an orifice-based flow meter with a difference

- Combines primary element with DP Transmitter in a single flow meter assembly

One-piece flowmeter, pressure tested as an assembly

- Improved reliability with no leaks to trace and rectify
- Integral multivariable transmitter and RTD for INTEGRAL reading of mass
(liquids and steam) and corrected volume (gas) flow rates in a single unit

Integral impulse connections

- No impulse piping installation required
- Provides repeatable DP connection across installation locations

Reduced cost of installation

- Only one piece to install
- Eliminates need to supply and connect separate manifold

Easy to specify
- Single ordering code covers complete flowmeter
- Only two orifice ratios simple specification process
 INTEGRAL ORIFICE
Model : DHIO-FM

The integral orifice is a flow element capable of

beingclose coupled with differential pressure
transmitters tomake a complete flow meter.
It provides easy-to-install, low-cost measurement of
the small flows found frequentlyin plant metering
operations and research projects.
It can be ordered with internal NPT threads or
flanged piperuns, welded both upstream and
downstream of the flowrestriction.
The orifice assembly may be directlymounted to the transmitter or remote using optionaladapter kit 155S711.

Model : DHIO-BN Model : DHIO-BY

Integral Orifice Block Type-a compact flow meter, providing measurement

Integrally in mass units for liquids and steam.
Gas flow is measured Integrally in reduced
volume units.

SPECIFICATIONS

Fluids Line Sizes

- Liquids, gases and saturated steam - 15A, 25A, 40A, 50A, 80A, 100A, 150A, 200A
Materials (1/2", 1 in., 11/2 in., 2 in., 3 in., 4 in., 6 in., 8 in.)
- Orifice assembly, stem and manifold : 316L Temperature limited
Orifice Body : 304 SS, 304L SS, 316 SS, 316L SS - Process : -40 to 121 °C (-4 to 250 °F)
Process Connections - Ambient : -40 to 70 °C (-4 to 158 °F)
- Wafer body to fit between the following flange
drillings:
- ASME
- ASMEB16.5
B16.5(ANSI)
(ANSI)Class
Class150,
150, 300,
300, 600, 900,
900,1500#
1500# (Model ::DHIO-BN,BY)
DHIO-BN,BY)
- ASME B16.5 (ANSI) Class 150, 300# (Model : DHIO-FM)
 INTEGRAL ORIFICE

MODEL SUFFIX CODES DESCRIPTION

FM Flange & Meter Run Included

DHIO- BN Block Type Meter Run Excluded

BY Block Type Meter Run Included

Nominal
Pipe size in inch or mm
Pipe Size

CS Carbon Steel

4S 304SS
Material
4L 304L SS
Plate or Block /
Meter Run 6S 316SS

6L 316L SS

OP Option

015 ASME(ANSI) Class 150 LB

030 ASME(ANSI) Class 300 LB

060 ASME(ANSI) Class 600 LB

Mounting Connection
090 ASME(ANSI) Class 900 LB

150 ASME(ANSI) Class 1500 LB

000 Option

V Volumetric
Indicator
M Mass

A 4~20mA
OutPut
V 1~5V

Option
 VENTURI TUBE �-1

MODEL : DHOV
DESCRIPTION
The Venturi tube is streamlined at both entrance
and exit. Standard designs are equipped with
piezo meter rings (i.e., multiple tap holes around
the periphery of inlet and throat, surrounded by an
annular ring). For measurement of slurries and
similar nonhomogenous liquids, the piezo meter
rings are usually eliminated to permit efficient
purging of the pressure tap holes. The Venturi tube
is considered the best type of head meter primary
device for measuring liquids containing large
concentrations of solids.
as a standard measurement for acceptance tests on pumping and similar equipment, the individually calibrated
Venturi tube has certain advantages. Like a calibrated orifice meter run, the calibration includes the effect o tap
characteristics.
The standard deviation of the test data, on classical type Venturi tubes with piezo meter rings at inlet and throat
connections, is between 0.3 and 0.4% The coefficients of properly constructed and installed Venturi tubes of this
type should agree with the data.
within ±0.75% on any pipe Reynolds number down to 200,000 on 95% of the installations.

SPECIFICATIONS
VENTURI TUBE TYPE
- Fabricated flange type : FIG 1
- Fabricated weld-on type : FIG 2
- Machined flange type : FIG 3
- Rectangular type : FIG 4

FLOW CALCULATION STANDARDS

- ISO5167, JIS Z 8762, ASME, KS A 0612

FLANGE RATING
- ANSI 150, 300, 600, 900, 1500LB

NOMINAL PIPE SIZES AVAILABLE

- 4 to 72B(100A to 1800A)

MATERIAL
- Carbon Steel
- 304SS, 304L SS, 316SS, 316L SS
- Ni, Cr, Mo Alloy Steel(A182 F11 to 91)
PRESSURE LOSS% DEVELOPED DIFFERENTIAL
 1

ANNULAR
VENTURI METER
ANNULAR VENTURI METER 2

1.0 / General
1.1 Introduction

The Annular venturi meter is a patented technology that accurately measures flow over a wide range of Reynolds

numbers, under all kinds of conditions and for a variety of fluids, It operates on the same physical principle as other

differential pressure-type flowmeters, using the theorem of conservation of energy in fluid flow through a pipe. The

Annular venturi meter remarkable performance characteristics, however, are the result of Its unique design, It

features a centrally-located cone inside the tube. The cone interacts with the fluid flow, reshaping the fluid’s velocity

profile and creating a region of lower pressure immediately downstream of itself. The pressure difference, exhibited

between the static line pressure and the low pressure created downstream of the cone, can be measured via two

pressure sensing taps, One tap is placed slightly upstream of the cone, the other is located in the downstream face of

the cone itself. The pressure difference can then be incorporated into a derivation of the Bernoulli equation to

determine the fluid flow rate. The cone’s central position in the line optimizes the velocity profile of the flow at the point

of measurement, assuring highly accurate, reliable flow measurement regardless of the condition of the flow upstream

of the meter.

1.2 Principles of Operation

The Annular venturi meter is a differential pressure type flowmeter.

Basic theories behind differential pressure type flowmeters have

existed for over a century. The principal theory among these is

Bernoulli’s theorem for the conservation of energy in a closed pipe.

This says that for a constant flow, the pressure in a pipe is inversely

proportional to the square of the velocity in the pipe. Simply, the

pressure decreases as the velocity increases. For instance, as the High and Low Ports
Figure 1
fluid approaches the Annular venturi meter, it will have a pressureof

P1, As the fluid velocity increases at the constricted area of the Annular venturi meter, the pressure drops to P2, as

shown in figure 1. Both P1 and P2 are measured at the Annular venturi meter’s taps using a variety of differential

pressure transducers. The Dp created by Annular venturi meter will increase and decrease exponentially with the flow

velocity. As the constriction takes up more of the pipe cross-sectional area, more differential pressure will be created

at the same flowrates. The beta ratio equals the flow area at the largest cross section of the cone (converted to an

equivalent diameter) divided by the meter’s inside diameter.

1.3 Reshaping the Velocity Profile

The Annular venturi meter is similar to other differential pressure (Dp) meters in the equations of flow that it uses.

Annular venturi meter geometry, however, is quite different from traditional Dp meters, The Annular venturi meter

constricts the flow by positioning a cone in the center of the pipe.

This forces the flow in the center of the pipe to flow around the cone. This geometry presents many advantages over

the traditional concentric Dp meter. The actual shape of the cone has been continuously evaluated and tested for over
ANNULAR VENTURI METER 3

ten years to provide the best performance under differing circumstances.

One must understand the idea of a flow profile in a pipe to

understand the performance of the Annular venturi meter. If the

flow in a long pipe is not subject to any obstructions or

disturbances, it is well-developed flow. If a line passes across the

diameter of this well-developed flow, the velocity at each point on

that line would be different. The velocity would be zero at the wall

of the pipe, maximum at the center of the pipe. and zero again at
Velocity Profile
the opposite wall. This is due to friction at the pipe walls that slows Figure 2

the fluid as it passes. Since the cone is suspended in the center of

the pipe, it interacts directly with the “high velocity core” of the flow. The cone forces the high velocity core to mix with

the lower velocity flows closer to the pipe walls. Other Dp meters have centrally located openings and do not interact

with this high velocity core.

This is an important advantage to the Annular venturi meter at lower flowrates. As the flowrate decreases, the

Annular venturi meter continues to interact with the highest velocity in the pipe. Other Dp meters may lose their useful

Dp signal at flows where the Annular venturi meter can still produce one.

The pipe flow profile in actual installations is rarely ideal. There are many insallations where a flowmeter exists in flow

that is not well developed. Practically any changes to the piping, such as elbows, valves, reductions, expansions,

pumps, and tees can disturb well-developed flow. Trying to measure disturbed flow can create a substantial problem

for other flowmeter technologies. The Annular venturi meter overcomes this by reshaping the velocity profile upstream

of the cone. This is a benefit derived from the cone′

s contoured shape and position in the line. As the flow approaches

the cone, the flow profile “flattens” toward the shape of a well-developed profile.

Flattened profile caaused by the

Annular Venturi Meter

Flattened Velocity Profile Figure 3

The Annular venturi meter can flatten the flow profile under even conditions, such as single elbows or double elbows

out-of-plane positioned closely upstream of the meter. This means that as different flow profiles approach the cone,

there will always be a predictable flow profile at the cone. This ensures accurate measurements even in non-ideal

conditions.
ANNULAR VENTURI METER 4

2.0 / Features
2.1 High Accuracy
The Annular venturi meter primary element can be accurate to ±0.5% of reading. The level of accuracy is dependent
to a degree on application parameters and secondary instrumentation.

2.2 Repeatabity
The Annular venturi meter primary element exhibits excellent repeatability of ＋0.1% or better

2.3 Turndown
The turndown of the Annular venturi meter can reach far beyond traditional Dp meters. A typical turndown for a
Annular venturi meter is 10 to 1. Greater turndowns are attainable. Flows with Reynolds numbers as low as 8000 will
produce a linear signal. Lower Reynolds numer ranges are measurable and are repeatable by a curve fit to the
measured Dp.

2.4 Installation Requirements

Since the Annular venturi meter can flatten the velocity profile, it can function much closer to upstream disturbances
than other Dp meters. The recommended installation for the Annular venturi meter is zero to three diameters of
straight run upstream and zero to one diameters downstream. This can be a major benefit to users with larger,
more expensive line sizes or users with small run lengths available. Dae Han instrument conducted performance tests
of the Annular venturi meter downstream of a single 90�elbow and two close coupled 90 elbows out of plane. These
tests show that the Annular venturi meter can be installed adjacent to either single elbows or two elbows out of plane
without sacrificing accuracy.

Single Elbow and Annular Venturi Meter Double Elbow and Annular Venturi Meter
Figure 4 Figure 5

2.5 Long Term Performance

The contoured shape of the cone constricts the flow without impacting it against an abrupt surface. A boundary layer
forms along the cone and directs the fluid away from the beta edge. This means the beta edge will not be as subject
to the usual wear by unclean fluids. The beta ratio will then remain unchanged and the calibration of the meter will be
accurate for a much longer time.

2.6 Signal Stability

Every Dp meter has a “signal bounce”. This means that even in steady flow, the signal generated by the primary
ANNULAR VENTURI METER 5

element will fluctuate a certain amount. On a typical orifice plate, the

vortices that form just after the plate are long. These long vortices
Annular
create a high amplitude, low frequency signal form the orifice plate. This Venturi Meter

could disturb the Dp readings from the meter. The Annular venturi meter
forms very short vortices as the flow passes the cone.
These short vortices create a low amplitude, high frequency signal. This Singlnal Stability
translates into a signal with high stability from the Annular venturi meter. Figure 2

Representative signals from a Annular venturi meter and from a typical

orifice plate are shown in figure 6.

2.7 Low Permanent Pressure Loss

Without the impact of an abrupt surface, the permanent pressure loss is lower than a typical orifice plate meter.
Also, the signal stability of the Annular venturi meter allows the recommended full scale Dp signal to be lower for the
Annular venturi meter than other Dp meters. This will lower the permanent pressure loss.

2.8 Sizing
The unique geometry of the Annular venturi meter allows for a wide range of beta ratios.
Standard beta ratios range from 0.45, 0.55, 0.65, 0.75, and 0.85.

2.9 No Areas of Stagnation

The “swept through” design of the cone does not allow for areas of stagnation where debris, condensation or particles
from the fluid could accumulate.

2.10 Mixing
The short vortices described above mix the fluid thoroughly just downstream of the cone. The Annular venturi meter is
currently in many applications as a static mixer where instant and complete mixing are necessary.

2.11 Two Models

Dae-han instrument offers two types of Annular venturi meter primary elements, the precision tube Annular venturi
meter and the insertion top-plate Annular venturi meter. Precision tube Annular venturi meter range in line sizes from
15A to 600A and larger; and insertion top-plateAnnular venturi meter range in line size from 150A”to 1800A and
larger.

Precision Tube Annular Venturi Meter

Figure 7 Insertion Top-plate Annular Venturi Meter
Figure 8
ANNULAR VENTURI METER 6

3.0 / Ordering informating

3.1 ANNULAR VENTURI METER STANDARD DIMENSIONS

(MODEL : DHAV-CC01)

FLANGE VERSION ▶

SIZE(mm) A(mm) B(mm) C(PT) C� REMARKS

15 203 64 1/4 6
20 203 64 1/4 6
150#, 300#
25 203 64 1/4 6
40 254 76 1/4 6 ANSI, RF
50 305 89 1/2 6
FLANGE
65 305 89 1/2 6
80 356 89 1/2 6
100 406 102 1/2 8
150 559 108 1/2 8
200 660 127 1/2 8
250 711 127 1/2 8
300 762 133 1/2 8
350 762 152 1/2 8
400 762 152 1/2 8
500 914 152 1/2 8
600 1219 254 1/2 8
1800 4000 254 1/2 12

LARGER ANNULAR VENTURI METER ON SPECIAL ORDER

* FLUID NAME

FLOW RATE (kg/hr, m3/hr)

PRESSURE (kpa)

MATERIAL (304SS, 316SS, etc)

LINE SIZE (3B sch20. sch40, etc)

ANNULAR VENTURI METER 7

3.2 ANNULAR VENTURI METER WELDED TYPE

(MODEL : DHAV-CC02)

A B D H C REMARKS
TOP PLATE sch. CON SIZE LINE SIZE 150# 300# ANSI RF
NPT
SIZE(mm) (mm) (mm) (mm) (mm) FLANGE
150 40 ~140 150~350 125 150 1/2
200 40 ~190 200~500 125 150 1/2
250 40 ~241 250~600 125 150 1/2
300 40 ~292 300~750 125 150 1/2
350 40 ~324 350~750 125 150 1/2
400 40 ~375 400~900 125 150 1/2
450 std ~425 450~1000 175 200 1/2
500 std ~476 500~1200 175 200 1/2
600 std ~578 600~1400 175 200 1/2
750 std ~730 750~1700 175 200 1/2
900 std ~883 900~2250 175 200 1/2
ANNULAR VENTURI METER 8

3.3 How To Order

STANDARD TYPE
(Model : DHAV-CC01)

MATERIAL PIPE FLANGE

LINE SIZE
CONE PIPE FLANGE SCHEDULE CLASS

015A 15 Z SS316 SS316 SS316 A 10 M ANSI 150#

020A 20 B 20 RF/SO
025A 25 Y SS304 SS304 SS304 C 40 Bored
040A 40 (15A~150A)
050A 50 X SS304 CS CS D std N ANSI 300#
065A 65 (400A ) RF/SO
080A 80 W Option Option Option E 40
100A 100 (200A~350A)
150A 150 F 80 O ANSI 600#
200A 200 G 160 RF/SO
250A 250
300A 300
350A 350 P ANSI 900#
400A 400 RF/SO
500A 500
600A 600
750A 750
900A 900

Ex : DHAV-CC01-100AYCM

WELDED TYPE
(Model : DHAV-CC02)

MATERIAL PIPE FLANGE

LINE SIZE
CONE PIPE FLANGE SCHEDULE CLASS

0400A 400 Z SS316 SS316 SS316 A 10 M ANSI 150#

0450A 450 B 20 RF/SO
0500A 500 Y SS304 SS304 SS304 C 40 Bored
0600A 600 D std
0750A 750 X SS304 CS CS (400A )
0900A 900 E 40
1000A 1000 W Option Option Option F 80
1200A 1200 G 160
1500A 1500
1800A 1800

Ex : DHAV-CC02-0600AXDM
 4-1

WEDGE METER

1. THE CHARACTERISTIC

DHWM-F / DHWM-BW / DHWM-T Series Wedge Meter

is an flow gauge(meter) that measure quantity of flow
in poor conditions.

DHWM-F Series can be measure to quantity of flow

like as Liquid, Gas, Steam, aas well as fluid included
sludge.

DHWM-F Specially, it is suitable to measure quantity of flow for

flow fluid with high viscosity.

It is possible to measure both flow.

DHWM-T

2. THEORY

DHWM-F Series estabilisbed Wedge of “V” type in

tube.

The quantity of flow is measured by pressure

difference of both side by means of wedge.

3. CAPACITY

Viscosity ±0.5% of measured value after

calibration(±3% before calibration)
Repeatability ±0.2
Maximum temperature 538� C
Range 10:1
H/D Ratio 0.2~0.5
Tube type 25A~600A
Straight line part of tube
Front 6 10D / Rear 3D
 4-2

WEDGE METER

4. DIEMENSION

WN-RF TYPE

Pipe A Dim(mm) Flange Rating B Dim C Dim D Dim(mm) Flange Rating

Size 150 300 600 (mm) (mm) 150 300 600
40A 530 543 559 292 146 208 214 213
50A 546 559 578 292 146 216 222 232
80A 622 641 660 311 156 156 167 175
100A 902 921 965 381 191 114 125 133
125A 965 972 1005 419 210 114 125 133
150A 1029 1048 1099 457 229 114 125 133
200A 1092 1111 1168 521 260 114 125 133
250A 1143 1175 1257 597 298 114 125 133
300A 1321 1353 1416 673 337 114 125 133
350A 1397 1429 1486 711 356 114 125 133
400A 1473 1511 1588 775 387 114 125 133
450A 1575 1613 1676 851 425 114 125 133
500A 1686 1721 1791 940 470 114 125 133
600A 1854 1886 1969 1067 533 114 125 133
 VENTURI NOZZLE �-1

MODEL : DHOV-N
DESCRIPTION
The profile of the Venturi nozzle is axisymmetric. It
consists of a convergent section, with a rounded
profile, a cylindrical throat and a divergent. The
upstream face is identical with that of an ISA 1932
nozzle. The Throat consists of a part E of length
0.3d witch is the same as for the ISA 1932 nozzle
and a part E' of a length 0.4d to 0.45d

The value d of the diameter of the throat shall be

taken as the mean of measurements of at least four
diameters distributed in axial planes and at
approximately equal angles to each other. The throat shall be cylindrical. No diameter of any cross-section shall differ
by more then 0.05% form the value of the mean diameter. This requirement is considered as satisfied when the
deviations in the length of any of the measured diameters comply with the said requirement in respect of deviation
from the mean. The divergent section shall be connected with the part E of the throat with out a rounded part, but
any burrs shall be removed.
The included angle of the divergent section, Ф. shall be less than or equal to 30°.
The Venturi nozzle may be truncated in the same way sa the classical venturi tube.

SPECIFICATIONS
VENTURI TUBE TYPE
- Threaded type : FIG 5
- Butt weld type : FIG 6
- Flanged type : FIG 7 Threaded

FIG 5
FLOW CALCULATION STANDARDS
- ISO5167, JIS Z 8762, ASME, KS A 0612

FLANGE RATING
Butt Weld
- ANSI 150, 300, 600, 900, 1500LB

FIG 6
NOMINAL PIPE SIZES AVAILABLE
- 0.5 to 120B(15A to 3000A)

MATERIAL
- Carbon Steel Flanged
- 304SS, 304L SS, 316SS, 316L SS
- Ni, Cr, Mo Alloy Steel(A182 F11 to 91)
FIG 7
 �-2

Required straight lengths for venturi nozzles

Values expressed as multiples of D
Downstream
(outlet)
Upstream (inlet) side of the primary device side of the
primary
Diameter device
ratio
Single 90 Two or more Two or more Reducer 2D Expander Globe valve Full bore ball Abrupt Thermometer Thermometer Fittings
bend or tee 90 bends in 90 bends in to D over 2 0.5D to D full open or gate valve symmetrical pocket or pocket or well (columns
β
(flow from the same different length of over a length fully open reduction well of of diameter 2 to 8)
one branch plane planes 1.5D to 3D of D to 2D having a diameter between
only) diameter ≤0.03D 0.03D and
MODEL : DHOV-N

ratio ≥0.5 0.13D

VENTURI NOZZLE

1 2 3 4 5 6 7 8 9 10 11 12
0.20 10 (6) 14 (7) 34 (17) 5 16 (8) 18 (9) 12 (6) 4 (2)
0.25 10 (6) 14 (7) 34 (17) 5 16 (8) 18 (9) 12 (6) 4 (2)
0.30 10 (6) 16 (8) 34 (17) 5 16 (8) 18 (9) 12 (6) 5 (2,5)
0.35 12 (6) 16 (8) 36 (18) 5 16 (8) 18 (9) 12 (6) 5 (2,5)
0.40 14 (7) 18 (9) 36 (18) 5 16 (8) 20 (10) 12 (6) 6 (3)
0.45 14 (7) 18 (9) 38 (17) 5 17 (9) 20 (10) 12 (6) 6 (3)
0.50 14 (7) 20 (10) 40 (20) 6 (5) 18 (9) 22 (11) 12 (6) 30 (15) 5 (3) 20 (10) 6 (3)
0.55 16 (8) 22 (11) 44 (22) 8 (5) 20 (10) 24 (12) 14 (7) 6 (3)
0.60 18 (9) 26 (13) 48 (24) 9 (5) 22 (11) 26 (13) 14 (7) 7 (3,5)
0.65 22 (11) 32 (16) 54 (27) 11 (6) 25 (13) 28 (14) 16 (8) 7 (3,5)
0.70 28 (14) 36 (18) 62 (31) 14 (7) 30 (15) 32 (16) 20 (10) 7 (3,5)
0.75 36 (18) 42 (21) 70 (35) 22 (11) 38 (19) 36 (18) 24 (12) 8 (4)
0.80 46 (23) 50 (25) 80 (40) 30 (15) 54 (27) 44 (22) 30 (15) 8 (4)
*) The installation of thermometer pockets or wells will not alter the required minimum upstream straight lengths for the other fittings.
NOTES
1. The minimum straight lengths required are the lengths between various fittings located upstream or downstream of the primary device and the primary device itself.
All straight lengths shall be measured from the upstream face of the primary device.
2. Values without parentheses are "zero additional uncertainty" values (see 7.2.3).
3. Values I parentheses are "0.5% additional uncertainty" values (see 7.2.4).
 VENTURI NOZZLE �-3

MODEL : DHOV-N

MODEL SUFFIX CODES DESCRIPTION

TM ------------------------------------------------------------------------- Threaded Male type

TF ------------------------------------------------------------------------- Threaded Female type

DHOV-N
BW ------------------------------------------------------------------------- Butt weld type

FL ------------------------------------------------------------------------- Flanged type

Nominal
Pipe ��� ------------------------------------------------ Pipe size in inch or mm
Size

CS ------------------------------------ Carbon Steel

4S ------------------------------------ 304SS

4L ------------------------------------ 304L SS

6S ------------------------------------ 316SS

6L ------------------------------------ 316L SS
Material
11 ------------------------------------ A182 F11

12 ------------------------------------ A182 F12

51 ------------------------------------ A182 F51

91 ------------------------------------ A182 F91

OP ------------------------------------ Option

015 ------------------------- ANSI Class 150 LB

030 ------------------------- ANSI Class 300 LB

060 ------------------------- ANSI Class 600 LB

Flange Connection 090 ------------------------- ANSI Class 900 LB

150 ------------------------- ANSI Class 1500 LB

NPT ��� -------------- Threaded

000 ------------------------- Option

0 ------------------ NPT 1/4

1 ------------------ NPT 1/2

Diff' Taps 2 ------------------ NPT 3/4

3 ------------------ SW 1/2

4 ------------------ SW 3/4

Option /���
 FLOW NOZZLE �-1

MODEL : DHON

DESCRIPTION
The Flow nozzles, more costly than other orifice due to
their structure, are suited for determining the flow rates
of fiuids flowing at high temperature and high pressure.
Under the same measuring conditions, a flow nozzle has
a higher mechanical strengh. can permit the flow of more
than 60 percent greater volume of a fluid, and can
measure the flow rates of fluids containing solid particles
less disturbed, than an orifice having the same bore.
Thus, they are suited, in addition, for highspeed flowing
fluids. We can supply not single flow nozzles, but also
flow nozzles having welded short pipes on both their
upstream and downstream sides.

SPECIFICATIONS
MOUNTING TYPE : ISO 5167 Long Radius MATERIAL
- Weld in type : FIG 1 - Carbon Steel
- Holding Ring type : FIG 2 - 304SS, 304L SS, 316SS, 316L SS
- Flange type : FIG 3 - Ni, Cr, Mo Alloy Steel(A182 F11 to 91)

FLOW CALCULATION STANDARDS βLIMIT

- ISO5167, JIS Z 8762, ASME, KS A 0612 - 0.2 �β � 0.8
- Low beta long radius nozzle 0.2 �β � 0.5
PRESSURE TAPS - High beta long radius nozzle 0.25 �β � 0.8
- 1D-1/2D taps

NOMINAL PIPE SIZES AVAILABLE

- 2 to 24B(50A to 600A)

High ratio Low ratio

0.25 �β � 0.8 0.2 �β � 0.5

Long radius nozzle

 FLOW NOZZLE �-2

MODEL : DHON

The flow nozzles are more expensive than orifice due to their structure, however, they are suitable for determining
the flow rates of fluids at high temperature and high pressure.
The flow nozzles can measure the flow rates of fluids containing a little amount of solid particles with les
inconvenience than orifices. under the same measuring conditions, the flow nozzle permits the flow rate of 60%
more than that of the same sized orifice, and also, it is suitable fo high velocity fluid because of a high mechanical
strength.
We can supply not only single flow nozzles, but also flow nozzle assembles having welded short pipes on both
upstream and down stream sides.

Weld in type : FIG 1

Holding Ring type : FIG 2

Flange type : FIG 3

 STEADY FLOW METER
Model : SFM300 Series

GENERAL MATERIAL
- Maximum Pressure : 30 kg/cm2G - Flow Conditioner : Aluminum, Carbon Steel 304(L)SS,
- Fluid : Gas 316(L)SS, etc
- Flow Rate : Range Table of Line size - Body : Carbon Steel, 304(L)SS, 316(L)SS
- Range Table of Line size (Air 760mmHgA, 20°C) Alloy Steel, etc.
Length(mm) - Sensor : 304(L)SS, 316(L)SS, Inconel,
Line Size Flow Range
Type
(Nm3/h)
A B Etoile Honey Comb Hastelloy, Alloy Steel, etc.
40 1 1/2 18~90 254 200
50 2 35~175 305 200
65 2 1/2 60~300 305 200
80 3 80~400 356 250
100 4 160~800 406 250
MOUNTING TYPE
125 5 250~1250 406 250
150 6 350~1700 559 250 - Body : Duct Flange, ASME(ANSI) Flange, etc.
200 8 600~2800 660 350
250 10 900~5000 711 350 - Sensor : Welded, Screw, Flange, etc
300 12 1600~7800 762 350
350 14 2000~9500 762 350
400 16 3000~14500 762 450
450 18 4000~19000 762 450 TRANSMITTER
500 20 5000~24000 914 450
550 22 5000~24000 914 450
600 24 6000~30000 1,220 600
- Connections : 2 Screw terminal block
650 26 7000~36000 1,220 600 - Output Signal : 4~20mADC(Limited at 30mADC)
700 28 8000~42000 1,220 600
750 30 9000~48000 1,220 600 - Loop Resistance : 0~1100Ω
800 32 10000~54000 1,220 600
850 34 11000~60000 1,520 600
900 36 12000~69000 1,520 600
950 38 13000~76000 1,520 600
1000 40 15000~85000 1,820 800
PERFORMANCE at 23�
C
1050 42 16000~94000 1,820 800
1100 44 18000~103000 1,820 800 - Zero Output : 4mA(Adjustable)
1200 48 21000~120000 1,820 800
1300 52 24000~145000 2,110 800
- Full Span Output : 20mA(Adjustable)
1400 56 29000~170000 2,110 1,000 - Operating Temperature : 0~400°C
1500 60 32000~190000 2,110 1,000
1600 64 37000~220000 2,530 1,000 100°C~over : (Fabricate Type)
1700~6000A *According to operation condition
※ SFM305Type Can use from above 600A

■ INSTALLATION INSTRUCTIONS
- Quantity : One - Quantity : Two
 STEADY FLOW METER
Model : SFM300 Series

■ ASSEMBLY DRAWING
 STEADY FLOW METER

■ ASSEMBLY DRAWING
■ ASSEMBLY DRAWING
PARSHALL FLUME
FLOW METER
Model : DHPF

www.dhinst.co.kr
 PARSHALL FLUME FLOW METER �-2

Model : DHPF

1. 개 요

2. 종 류

3. 기 능

4. 특 징
 PARSHALL FLUME FLOW METER �-3

Model : DHPF

5. 사 양
 PARSHALL FLUME FLOW METER �-4

Model : DHPF

5. 사 양

6. Parshall Flume Size

 PARSHALL FLUME FLOW METER �-5

Model : DHPF

7. Local Panel & Cutting size

8. 현장 설치 예

9. Flow Meter System DWG

 PARSHALL FLUME FLOW METER �-6

Model : DHPF

MODEL SUFFIX CODES DESCRIPTION

U -------------------------------------------------------------------- Ultrasonic type

DHPF�
F -------------------------------------------------------------------- Float type

1I ------------------------------------------------ 1 Inch
2I ------------------------------------------------ 2 Inch
3I ------------------------------------------------ 3 Inch
6I ------------------------------------------------ 6 Inch
9I ------------------------------------------------ 9 Inch
1F ------------------------------------------------ 1 Feet
Nominal
Parshall Flume 1.5F ---------------------------------------------- 1.5 Feet
Size
3F ------------------------------------------------ 3 Feet
4F ------------------------------------------------ 4 Feet
5F ------------------------------------------------ 5 Feet
6F ------------------------------------------------ 6 Feet
7F ------------------------------------------------ 7 Feet
8F ------------------------------------------------ 8 Feet
CS -------------------------------- Carbon Steel
4S -------------------------------- 304SS
Parshall Flume Material 6S -------------------------------- 316SS
6L -------------------------------- 316L SS
FR -------------------------------- FRP
CS ----------------------- Carbon Steel
4S ----------------------- 304SS

Panel Material 6S ----------------------- 316SS

6L ----------------------- 316L SS
FR ----------------------- FRP
A ---------------- 4~20mA

Output V ---------------- 1~5V

R ---------------- etc
Option /���
 CONDENSATE POT
Model : DHCP

� DESCRIPTION CONDENSATE POT는 다음과 같은 증기나 응축성이

강한 기체의 측정에 사용된다.
1) 증기의 경우는 증기온도가 200도 이상이 되기 때문에 반드시 증
기를 응축시켜 액체상태로 만들어 측정하고자 할 때 사용된다.
그러므로 사전에 POT와 계기사이에 응축액을 봉입하여 둔다.
단, 증기온도가 200도 이하일 경우는 발신기가 다이아프램 형의
힘 평형식 차압계와 같이 TEE와 PLUG 만으로도 충분하다.
2) CONDENSATE POT는 측정물의 응축을 용이하게 하고 계기 접
액 부분의 용적변동을 최소화 시킬 수 있도록 뉘여서 사용함으
로써 응축액의 접촉면적을 넓게 한다.
3) CONDENSATE POT는 응축액이 일정한 레벨이 되면 그 이상은
본관으로 회수되도록 취출 노즐의 수평에서 위쪽으로 45도 범
위 내에서 고, 저압 모두 동일 레벨이 되도록 취부 한다.

� HOW TO ORDER
MODEL SUFFIX CODES DESCRIPTION
4B ------------------------------------------------------------------- 4
3B ------------------------------------------------------------------- 3
DHCP
2-1/2B -------------------------------------------------------------- 2.5
2B ------------------------------------------------------------------- 2
10 ------------------------------------------------ 01
20 ------------------------------------------------ 02
Pipe sch 40 ------------------------------------------------ 04
80 ------------------------------------------------ 08
160 ------------------------------------------------ 16
STPG ----------------------------- SG
STPT ------------------------------ ST
Material
304(L)SS ------------------------- 4(L)S
316(L)SS ------------------------- 6(L)S
PT1/2 -------------------- P1
PT3/4 -------------------- P3
Connection
NPT1/2 ------------------ N1
NPT3/4 ------------------ N3
S.W1/2 ------------------ S1
S.W3/4 ------------------ S3
Plug ------------ P
Plug & Vent Plug
Vent Plug ----- V
Option /���