LR 1250.

1
EN

LR 1004.03.08
www.liebherr.com

Crawler cranes
Concept and characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Technical description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Transport dimensions and weights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Self-assembly system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Boom combinations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Main boom 2320.xx . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Luffing jib 1713.xx . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Luffing jib 1916.xx . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Fixed jib 1008.xx . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Fixed jib 0806.xx . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Fixed jib 0906.21 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Remarks
– The load capacities stated are valid for lifting operation only (corresponding with
crane classification according to ISO 4301‑1, crane group A1).
– Machine is standing on firm, horizontal ground.
– The weight of the lifting device (pulley block, hoist ropes, shackles, etc.) must be
deducted from the load capacity.
– Additional equipment on boom (e.g. walkways) must be deducted from the load
capacity.
– The max. admissible wind speed can be preselected in the LML software and
referred to in the load chart.
– Working radii are measured from centre of swing ring and under load.
– The lifting capacities are valid for 360 degrees of swing.
– Calculation of stability under load is based on ISO 4305 Table 1 + 2 + 3, tipping angle 4°.
– The steel structures are calculated according to EN 13001-1; EN 13001-2.
– The last digits of the given dimensions are rounded to 0 and 5 and may differ from
the actual dimensions.
– Weights may vary depending on the delivered configuration of the machine, filling
level of the tanks, as well as generally valid tolerances.
– The illustrations in this brochure may include options which are not within the
standard scope of supply of the machine.

2 LR 1250.1
Concept and characteristics
---

Pulley block with

additional weights

Main boom Pendants

A-frame

Rear counterweight

Uppercarriage

Undercarriage

LR 1250.1 3
Cabin with high comfort
– optimized view
– noise-reducing design
– orthopaedic seat

Additional
safety platform

Crawler side frames with

1200 mm flat track pads

Carbody counterweight 9.8 t

Storage compartment for tools

Platforms

High performance Ground pressure

A strong, efficient and reliable diesel The actual ground pressure is
engine of the newest generation pro‑ cal­culated according to the confi­
vides high performance and enables guration and position of the machine
several movements to be carried out and displayed in the operator’s cabin.
simultaneously. Using the optional Liebherr Crane
Planner the actual ground pressure
can already be calculated and dis‑
played in the planning stage.

Cabin with high comfort Control system

Optimised field of vision combined Easy and intuitive handling of con‑
with enhanced comfort: an orthopae‑ trol, service and machine functions
dic operator’s seat with heating and through a large, clear colour moni‑
cooling functions, as well as precise tor. Built for extreme environmental
and ergonomic controls are included. conditions.

4 LR 1250.1
 Pulley set

Rear counterweight:
Counterweight slab 5 t
Basic counterweight
slab 12 t

Storage compartment
for tools

Efficient self-assembly system Mobility

and short assembly times Crane parts are optimized for trans‑
The self-assembly system enables portation. The maximum transport
safe, independent and quick assem‑ width is 3 m.
bly/disassembly of the crawler side
frames, the carbody and rear counter‑
weights, as well as boom elements.

Easy service Boom/jib

The design ensures easy maintenance A variety of boom systems and con‑
and service as well as safe access to figurations allow for optimum opera‑
the components. tion on the most diverse jobsites.

LR 1250.1 5
Technical description
---
Diesel engine Swing gear
Power rating according to ISO 9249 230 kW (308 hp) at 1700 rpm Drive system with fixed axial piston hydraulic motors, planetary
Engine type Liebherr D 944 A7-05 gearbox, pinion
Fuel tank capacity 790 l with continuous level indicator and reserve warning Swing ring roller bearing with external teeth
Exhaust certification 97/68 EC Stage IV; EPA/CARB Tier 4f Brake hydraulically released, spring–loaded multi–disc holding
97/68 EC Stage V; EPA/CARB Tier 4f brake
ECE-R.96 Power Band H Swing speed 0-3 rpm continuously variable
non-certified emission standard Speed control both swing modes are possible – speed control or free
swing
for speed control: a multi–disc holding brake locks
automatically at zero swing motion.

Noise measurement data and vibration

Noise emission according to 2000/14/EC directive
Emission sound pressure level L PA 74.0 dB(A) (in the cabin)
Guaranteed sound power level LWA 105 dB(A) (of the machine) Hoisting gear
Vibration transmitted to the < 2.5 m/s² (to the hand-arm system) Standard Internal low-maintenance planetary gearbox in oil bath,
machine operator < 0.5 m/s² (to the whole body) crane winches 1 + 2 load support by the hydraulic system, spring–loaded,
multi–disc holding brake, pressure controlled, variable
flow hydraulic motors for the main winches, full utilisa-
tion of engine power as the winch speed is automatically
adjusted to suit the respective line pull
Line pull in the 7 th layer 120 kN
Hydraulic system Rope diameter 26 mm
Hydraulic pumps double axial displacement pump in open loop Drum diameter 580 mm
hydraulic system allows all functions to be operated Rope speed 0-136 m/min
­simultaneously Rope capacity in 7 layers 489 m
automatic working pressure cut–off to minimize peak Option – winch with free fall Free fall: clutch and braking functions are provided
pressure by the service brake (low wear and maintenance-free
Hydraulic oil tank capacity 650 l multi–disc brake in compact design)
Max. working pressure 350 bar
Hydraulic oil electronic monitoring of alle filters
use of synthetic environmentally friendly oil

Boom/jib luffing winches

Main boom
Line pull max. 180 kN
Control Rope diameter 24 mm
Control system includes all control and monitoring functions, designed Boom luffing 15-86° in 130 s
to withstand extreme environmental conditions and Jib
heavy construction tasks Line pull max. 105 kN
Display high resolution monitor in the operator’s cabin, Rope diameter 20 mm
clear display of complete machine operating data, war- Jib luffing 15-78° in 51 s
nings and failure indications in the required language
Operation several movements can be performed simultaneously
thanks to electro-hydraulic proportional control, all cate-
gories of loads can be positioned with utmost precision

Operating weight
Composition of operating weight basic machine with crawlers
winches 1 + 2 (incl. ropes), A-frame
20 m main boom, consisting of boom foot (10 m), boom
Crawlers head (7 m) and boom section (3 m)
Drive system with fixed axial piston hydraulic motors 82.3 t rear counterweight (14 × 5 t + 1 × 12 t+ 0.3 t)
Crawler side frames maintenance-free, with hydraulic chain tensioning device 36 t carbody counterweight (2 × 9.8 t + 2× 8.3 t)
Brake hydraulically released, spring–loaded multi–disc holding 250 t pulley block
brake Total weight approx. 210 t
Drive speed 0-1.6 km/h
Flat track pads width 1200 mm

6 LR 1250.1
Operation modes

Lifting mode Grab mode Personnel lifting mode

✓ ✓ ✓
Land

✓ ✓ ✓*
Floating structure
(barge operation)
* only valid for jack-up barges

Optional equipment
Basic machine Service package
Main winches 12 t with free fall Refuelling pump diesel / AdBlue
Painting in customer design Cold package -25 °C / -40 °C
Load hook 12.5 / 40 / 80 / 100 / 160 / 250 t Hydraulic oil bypass filter
Economy and ecology Central lubrication swing ring bearings / outside
Eco-Silent Package Liebherr hydraulic oil plus (longlife & bio)
Aux. power unit (APU, 2.8 kW) Liebherr hydraulic oil plus arctic (longlife & bio)
Boom/jib Liebherr hydraulic oil plus arctic (longlife)
Luffing jib: luffing winch Safety features
Carbon fibre pendants Assistance system: Boom Up-and-Down Assistant
Boom/jib other Assistance system: Horizontal Load Path
Walkway for main boom foot, incl. fall protection Assistance system: Vertical Line Finder
Walkway for main boom head, incl. fall protection Assistance system: Ground Pressure Indication and Visualization
Rope guide for main boom walkway, incl. fall protection Rear and side view cameras
Additional fall protection harness for 1 person Winch camera
Walkways for main boom sections 3 / 6 / 12 m Zoom camera at boom head
Walkways for main boom sections 3 / 6 / 12 m, incl. fall protection Safety upgrade APAVE
Application packages Platforms and railings on uppercarriage 570 mm
Operation mode: personnel lifting (O) Additional access ladder for boom assembly
Operation mode: barge operation (O) Railings on rooftop foldable
Operation mode: foundation work (O) Railings for cabin platform
Operation mode: wind speed pre-selection (S) Vandalism cabin protection
Operation mode: travelling with load (S) Cabin protection roof, FOPS level 1
Winch synchronization Lifting height indication for both hoist winches
Radio remote control Plug&Play diesel-hydraulic back-up unit 18.4 kW
Rope reeving function via radio remote control Swing and boom radius limit device
Assembly radio remote control Aircraft warning light
Use of luffing jib winch as auxiliary winch Swing warning light
Tagline winch 2 t free fall Lightning rod
Main winch constant tension for one winch Mechanical angle display
Two hook operation Air intake shut-off valve
Cabin elevator 6 m hydraulic Access control
Special features Operator’s comfort
Crane Planner 2.0 Additional access ladder
LiDAT Additional floodlights
Self-assembly system Cabin air conditioner
Jack-up system standard / telescopic Cabin tilting device hydraulic
Self-assembly system counterweight Gear oil level warning
Self-assembly cylinder Litronic additional language
Reeving winch (S) standard, (O) option
Track shifting hydraulic

LR 1250.1 7
Dimensions
---
Basic machine with undercarriage

0
71
R8

11105 6050
3450

4915
1450

1345
* Boom pivot point 1500* 3740 1200

535
7540 7000
8700 1505
0
20
R6

7610
19235

8 LR 1250.1
Transport dimensions and weights
---
Basic machine and main boom 2320.xx
2985 Basic machine
Weight without hoist rope kg 37228
Weight of hoist ropes kg/m 3.4
3290
with A-frame 1, winches 1 + 2 (2x 120 kN), without boom foot, without rear counterweight,
without carbody counterweight and crawler side frames
1425 (option) 975

11080 3370

Crawler side frame

1345
Weight flat track pads 1200 mm kg 19658

8700 1335

Boom foot 10 m (No. 2320.25)

2480 Weight including winch kg 4827
Weight without winch kg 3737

10260 2430

Boom section 3 m (No. 2320.23)

2305 Weight including boom pendants kg 871
Weight including boom and jib pendants kg 959

3170 2430

Boom section 6 m (No. 2320.23)

2305 Weight including boom pendants kg 1344
Weight including boom and jib pendants kg 1497

6170 2430

Boom section 12 m (No. 2320.23)

2305 Weight including boom pendants kg 2434
Weight including boom and jib pendants kg 2737

12155 2430

Boom section 7m (No. 2320.23)

Weight including boom pendants kg 3613
2955

8065 2430

Transport option 2320.xx / 1916.xx

Transport option (No. 2320.xx / 1916.xx)

2305 No. 2320.xx / 1916.xx m 3/3 6/6 12 / 12
Weight including pendants kg 1453 2228 4027

Max. 12155 2430

LR 1250.1 9
Fixed jib 1008.xx
Jib head 5.5 m (No. 1008.20)
1080
Weight including pendants kg 873
6585 1095

Jib section 3 m (No. 1008.17)

1065
Weight including pendants kg 267
3140 1095

Jib section 6 m (No. 1008.17)

1065
Weight including pendants kg 448
6140 1095

Jib foot 5.5 m with A-frame (No. 1008.20)

1605 Weight including pendants kg 2110

5710 2385
6640

Fixed jib 0806.xx

1155
Jib head 5.5 m (No. 0806.16)
Weight including pendants kg 442
6025 920

870 Jib section 3 m (No. 0806.15)

Weight including pendants kg 141
3125 930

905 Jib section 6 m (No. 0806.15)

Weight including pendants kg 249
6120 930

Jib foot 5.5 m with A-frame (No. 0806.16)

1155
Weight including pendants kg 1017

5635 2500
6810

Fixed jib 0906.21

Fixed jib 7 m (No. 0906.21)
Weight including pendants kg 2413
1830

8135 1420
9315 2345

10 LR 1250.1
Luffing jib 1713.xx
Jib head 7 m (No. 1713.21)
2140 Weight including pendants kg 1376

7760 1805

Jib section 3 m (No. 1713.18)

1570
Weight including pendants kg 394

3140 1805

Jib section 6 m (No. 1713.18)

1570
Weight including pendants kg 624

6140 1805

Jib section 12 m (No. 1713.18)

1570
Weight including pendants kg 1122

12140 1805

Jib foot 7 m with A-frames 2 + 3 (No. 1713.22)

Weight including pendants kg 4763
2905

7405 1835
8500

Luffing jib 1916.xx

Jib head 7 m (No. 1916.21)
2155 Weight including pendants kg 1520

7735 2005

Jib section 3 m (No. 1916.18)

1870 Weight including pendants kg 494

3145 2010

Jib section 6 m (No. 1916.18)

1870 Weight including pendants kg 731

6145 2010

Jib section 12 m (No. 1916.18)

1870 Weight including pendants kg 1287

12145 2010

Jib foot 7 m with A-frames 2 + 3 (No. 1916.22)

Weight including pendants kg 6237
3770

9680 2020
10620

LR 1250.1 11
Counterweight

640 Basic counterweight slab without tie-down (1x)

Weight kg 12000
6050 1365

1365

6050

480 Counterweight slab (14x)

1905 1365 Weight kg 5000

1365

1905

200
Carbody counterweight slab (2x)
2880 1800 Weight kg 8300

1800

2880

620 Carbody counterweight (2x)

Weight kg 9800
2350 2800

2800

2350

12 LR 1250.1
Pulley block with additional weights / load hooks

250 t pulley block – 11 pulleys

770
Width mm 1250
Weight kg 2300 / 3200
2280

160 t pulley block – 7 pulleys

770
Width mm 885
Weight kg 1500 / 2250 / 3000
2110

100 t pulley block – 5 pulleys

770
Width mm 745
Weight kg 1300 / 1800 / 2300
1890

80 t pulley block – 3 pulleys

770
Width mm 565
Weight kg 1000 / 1500 / 2000
1815

40 t pulley block – 1 pulley

770
Width mm 490
Weight kg 700 / 1100 / 1500
1625

Ø 400 12.5 t load hook

Weight kg 600
1115

LR 1250.1 13
Self-assembly system
---

Unloading of basic machine

Unloading and assembly of boom foot

Unloading and assembly of crawler side frames

Unloading and assembly of carbody counterweight Unloading and assembly of boom

Unloading and assembly of rear counterweight

14 LR 1250.1
Assembly of boom

Reeving of hoist and luffing jib ropes

Erecting of main boom and luffing jib

LR 1250.1 15
Boom combinations
---

5.5 m (1008.20)
Fixed jib Fixed jib
0906.21 6 m (1008.17) 1008.xx
7 m (2320.23)
7 m (0906.21) 6 m (1008.17)

3 m (1008.17)

12 m (2320.23) 7 m (2320.23) 5.5 m (1008.20)

7 m (2320.23)
12 m (2320.23)
12 m (2320.23)

12 m (2320.23)

12 m (2320.23)
12 m (2320.23)
12 m (2320.23)

12 m (2320.23)
12 m (2320.23)
12 m (2320.23)

12 m (2320.23)
12 m (2320.23) Main boom Main boom Main boom
2320.xx 2320.xx 12 m (2320.23) 2320.xx

6 m (2320.23) 12 m (2320.23)
6 m (2320.23)
3 m (2320.23)

10 m (2320.25) 10 m (2320.25) 10 m (2320.25)

Main boom Main boom + fixed jib Main boom + fixed jib
Mode 1 Mode 3 Mode 3
Max. length Max. combination Max. combination
2320.xx m 86 2320.xx m 77 2320.xx m 71 74
Further information on page 18. 0906.21 m 7 1008.xx m 26 17
Total length m 84 Total length m 97 91
Further information on page 38. Further information on page 32.

16 LR 1250.1
 7 m (1916.21)

7 m (1713.21)

12 m (1916.18)

12 m (1713.18)

12 m (1916.18)

12 m (1713.18) Luffing jib Luffing jib

1713.xx 1916.xx
5.5 m (0806.16) 12 m (1916.18)

12 m (1713.18)
6 m (0806.15)

6 m (0806.15) 12 m (1916.18)

Fixed jib 12 m (1713.18)

6 m (0806.15)
0806.xx
3 m (0806.15) 12 m (1916.18)
5.5 m (0806.16)
12 m (1713.18)

7 m (2320.23)
12 m (1916.18)
6 m (1713.18)

3 m (1713.18)
12 m (2320.23) 6 m (1916.18)
7 m (1713.22)
3 m (1916.18)

7 m (2320.23) 7 m (1916.22)
12 m (2320.23)
7 m (2320.23)
12 m (2320.23)

12 m (2320.23)
12 m (2320.23)

12 m (2320.23)

12 m (2320.23) 12 m (2320.23)
Main boom Main boom
2320.xx 12 m (2320.23) 2320.xx

12 m (2320.23) 12 m (2320.23)
6 m (2320.23)

10 m (2320.25) 10 m (2320.25) 10 m (2320.25)


Main boom + fixed jib Main boom + luffing jib Main boom + luffing jib
Mode 3 Mode 4 Mode 4
Max. combination Max.combination Max. combination
2320.xx m 77 80 2320.xx m 59 62 65 2320.xx m 53 56 59
0806.xx m 32 23 1713.xx m 83 65 44 1916.xx m 95 74 53
Total length m 109 103 Total length m 142 127 109 Total length m 148 130 112
Further information on page 35. Further information on page 20. Further information on page 26.

LR 1250.1 17
Main boom 2320.xx
---
Main boom lengths 20-86 m
Units in m
96

80° 86°

70°
84
36 t
60°

72 °
50
86 1210-2000
83
80
60 77
74
°
40

71 Auxiliary jib 36 t (option)

68
65 The maximum capacity of the aux‑
62
48 59 iliary jib is 36 t. The corresponding
30°

56
53 load chart is programmed in the LML
50
47 system.
36 44
41
20°

38
35
32
1 5°

24 29
26
23
20

12
0°

0
96 84 72 60 48 36 24 12 0

Main boom configuration 2320.xx

Boom section Amount of boom sections
Boom foot 10 m 1 1 1 1 1 1 1 1 1 1 1 1
Boom section 3 m 1 1 1 1 1 1
Boom section 6 m 1 1 1 1 1 1
Boom section 12 m 1 1 1 1 2 2 2 2 3
Boom head 7 m 1 1 1 1 1 1 1 1 1 1 1 1
Boom length [m] 20 23 26 29 32 35 38 41 44 47 50 53
Auxiliary jib ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓

Boom foot 10 m 1 1 1 1 1 1 1 1 1 1 1
Boom section 3 m 1 1 1 1 1 1
Boom section 6 m 1 1 1 1 1 1
Boom section 12 m 3 3 3 4 4 4 4 5 5 5 5
Boom head 7 m 1 1 1 1 1 1 1 1 1 1 1
Boom length [m] 56 59 62 65 68 71 74 77 80 83 86
Auxiliary jib ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓

18 LR 1250.1
Load capacities with main boom
Load capacities in [t] with 82.3 t rear counterweight and 36 t carbody counterweight
Boom length [m]
20 26 32 38 44 50 56 62 68 74 80 86
5.8 122.1
6 143.5 122.1
7 149.9 136.5 117.5 101.4 86.4 72.1
8 139.3 132.4 124.5 112.6 96.9 83.4 71.5 59.1 49.8
9 129.7 122.7 115.9 109.6 103.9 93.0 80.4 68.1 57.7 49.5 41.2 34.0
12 87.5 87.5 83.8 80.0 76.6 73.4 70.3 61.3 52.9 45.8 39.6 32.7
18 50.0 50.0 49.9 49.6 49.1 47.3 45.6 43.9 42.3 38.7 34.4 29.2
20 43.3 43.4 43.3 43.0 42.7 41.9 40.4 38.9 37.5 36.1 32.4 28.2
Radius [m]

22 38.2 38.1 37.8 37.5 37.1 36.2 34.9 33.6 32.3 30.6 26.9
28 27.4 27.1 26.8 26.4 26.1 25.7 24.9 23.9 22.9 21.9
34 20.5 20.3 19.9 19.5 19.1 18.7 18.2 17.4 16.5
38 17.3 17.1 16.7 16.4 15.9 15.5 15.1 14.7 13.8
40 15.8 15.4 15.0 14.6 14.2 13.8 13.3 12.6
44 13.4 13.1 12.8 12.4 12.0 11.6 11.2 10.6
46 12.1 11.9 11.4 11.0 10.6 10.2 9.7
50 10.4 10.2 9.7 9.3 8.9 8.5 8.0
55 8.3 8.0 7.6 7.1 6.7 6.2
60 6.5 6.1 5.7 5.2 4.8
65 4.8 4.4 4.0 3.5
70 3.3 2.9 2.5
75 2.0

Load capacities in [t] with 72.3 t rear counterweight and 36 t carbody counterweight
Boom length [m]
20 26 32 38 44 50 56 62 68 74 80 83
4.1 219.1
5 216.9 199.9 173.7
6 194.3 180.1 165.5 143.5 122.1
7 164.9 152.4 141.7 132.2 117.5 101.4 86.4 72.1
8 138.9 129.7 121.6 114.3 107.8 96.9 83.4 71.5 59.1 49.8
10 104.8 99.5 94.4 89.6 85.3 81.2 77.1 65.7 56.0 48.1 40.7 36.9
12 80.2 80.1 76.7 73.3 70.1 67.1 64.2 61.3 52.9 45.8 39.6 35.9
14 64.5 64.5 64.4 61.7 59.2 56.8 54.6 52.4 50.0 43.2 37.6 34.3
Radius [m]

18 45.7 45.7 45.5 45.2 44.7 43.0 41.4 39.8 38.3 36.8 34.4 31.5
22 34.7 34.6 34.3 34.0 33.7 32.8 31.5 30.3 29.0 27.9 27.3
26 27.5 27.5 27.2 26.9 26.5 26.2 25.6 24.6 23.5 22.5 22.0
30 22.4 22.2 21.9 21.5 21.1 20.7 20.3 19.3 18.4 18.0
34 18.4 18.1 17.7 17.4 17.0 16.6 16.1 15.2 14.8
36 16.8 16.6 16.2 15.8 15.4 15.0 14.6 13.9 13.5
38 15.4 15.2 14.8 14.5 14.1 13.7 13.2 12.7 12.3
44 11.9 11.6 11.2 10.8 10.4 10.0 9.5 9.3
50 9.1 8.8 8.3 7.9 7.5 7.1 6.9
55 7.1 6.7 6.3 5.9 5.4 5.2
60 5.3 4.9 4.5 4.1 3.9
65 3.8 3.4 2.9 2.7
70 2.4

TLT 11962152. Above load charts are for reference only. For actual lift duty please refer to load
chart in operator’s cabin or manual. Otherwise we recommend you to plan your lifting job using
Crane Planner 2.0.

LR 1250.1 19
Luffing jib 1713.xx
---
Jib lengths 20-83 m
Units in m 78°
144 7 3°

60°
132 12 t
°
50

120
80 3
8

1080-1770
°
40

77
74
68 1
7

108
Auxiliary jib 12 t (option)
65
30°

62

The maximum capacity of the

59
56

­auxiliary jib is 12 t.
50 3
5

96
44 7
4
20°

38 1
4
35

84
1 5°

32
29
26
23
20

72
83° 88°
7 5°
6 5°
0°

60
5 5° 65
62
59
56
°
45

48 53
50
47
44
41
36
38
35
32
29
24 26
23
20

12
0°

0
108 96 84 72 60 48 36 24 12 0

Jib configuration 1713.xx

Jib section Amount of jib sections
Jib foot 7 m 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Jib section 3 m 1 1 1 1 1 1 1 1 1 1 1
Jib section 6 m 1 1 1 1 1 1 1 1 1 1 1 1
Jib section 12 m 1 1 1 1 2 2 2 2 3 3 3 3 4 4 4 4 5 5 5 5
Jib head 7 m 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Jib length [m] 20 23 26 29 32 35 38 41 44 47 50 53 56 59 62 65 68 71 74 77 80 83
Auxiliary jib ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓
For main boom configuration please refer to the table on page 18.

20 LR 1250.1
Load capacities with luffing jib

Load capacities in [t] with 20 m main boom 88° Load capacities in [t] with 29 m main boom 88°
Jib length [m] Jib length [m]
20 32 44 56 68 83 20 32 44 56 68 83
9 60.0 8.1 60.0
11 52.2 46.1 11 55.8 44.3
13 42.1 37.8 30.3 14 40.4 36.0 28.4
16 32.1 29.4 26.8 18.8 16 34.2 31.3 26.7 17.9
Radius [m]

Radius [m]
18 27.6 25.2 22.8 17.9 12.0 18 29.4 26.6 23.7 17.1
22 19.7 19.7 18.0 15.7 11.0 6.9 20 25.6 23.9 21.7 16.3 11.1
24 17.7 16.2 14.7 10.5 6.7 22 22.2 20.9 19.0 15.5 10.5 6.4
36 9.9 8.7 7.7 5.4 32 13.3 12.1 10.9 8.6 5.6
44 7.5 6.6 5.7 4.7 42 8.6 7.5 6.4 4.8
55 4.7 3.9 3.0 48 6.3 5.3 4.1
60 3.4 2.4 60 3.6 2.7
65 2.8 65 3.0 2.2
82.3 t rear counterweight and 36 t carbody counterweight 82.3 t rear counterweight and 36 t carbody counterweight

Load capacities in [t] with 41 m main boom 88° Load capacities in [t] with 50 m main boom 88°
Jib length [m] Jib length [m]
20 32 44 56 68 83 20 32 44 56 68 83
8.6 60.0 8.9 50.8
11 53.6 39.2 12 44.9 34.6
14 42.2 35.3 25.6 14 40.5 32.9 22.8
16 35.5 32.0 24.5 16.4 18 31.1 27.0 21.1 14.5
Radius [m]

Radius [m]

20 26.5 24.0 21.5 15.4 10.2 20 27.0 24.4 20.1 13.9 9.4
22 23.2 21.5 19.3 14.6 9.9 5.8 22 23.9 21.8 18.7 13.3 9.2 5.2
30 14.7 13.3 11.7 8.7 5.4 30 14.9 13.2 11.3 8.2 5.0
36 10.6 9.4 7.9 5.0 36 10.7 9.2 7.6 4.8
48 6.4 5.4 4.0 46 7.7 6.7 5.7 4.1
55 5.2 4.3 3.3 55 5.1 4.4 3.3
60 3.7 2.8 65 3.2 2.4
70 2.4 70 2.5
82.3 t rear counterweight and 36 t carbody counterweight 82.3 t rear counterweight and 36 t carbody counterweight

Load capacities in [t] with 62 m main boom 88°

Jib length [m] TLT 11962152. Above load charts are for reference only. For actual lift duty please refer to
20 32 44 56 62 65 load chart in operator’s cabin or manual. Otherwise we recommend you to plan your lifting job
using Crane Planner 2.0.
9.3 36.4
12 34.3 25.2
16 30.1 23.3 17.4
18 27.7 22.2 16.8 12.0
Radius [m]

20 24.8 21.3 16.1 11.6 9.5 8.7

26 16.7 14.7 10.5 8.9 8.2
34 12.8 11.5 9.6 8.5 7.7
36 10.8 9.0 8.3 7.6
46 7.8 6.7 6.3 5.9
55 5.2 4.8 4.6
60 4.2 4.0
65 3.4
82.3 t rear counterweight and 36 t carbody counterweight

LR 1250.1 21
Load capacities with luffing jib

Load capacities in [t] with 20 m main boom 83° Load capacities in [t] with 29 m main boom 83°
Jib length [m] Jib length [m]
20 32 44 56 68 83 20 32 44 56 68 83
11.3 59.9 12.4 59.9
16 36.9 33.5 16 42.8 36.4
20 27.2 24.5 22.1 20 30.7 27.6 24.3
22 23.8 21.7 19.6 16.3 24 23.7 21.6 19.6 15.5
Radius [m]

Radius [m]
24 20.4 19.3 17.4 15.7 26 19.2 17.4 14.8
26 17.6 15.8 14.3 10.2 28 17.5 15.9 14.2 9.8
28 16.0 14.4 13.0 10.0 30 16.0 14.5 12.9 9.5
30 14.7 13.1 11.8 9.7 6.1 36 12.5 11.4 10.1 8.4 5.5
38 9.8 8.6 7.6 5.5 40 10.0 8.7 7.6 5.2
55 5.1 4.2 3.1 48 7.6 6.8 5.7 4.5
60 3.6 2.6 50 6.4 5.3 4.2
70 2.5 70 2.8 2.0
82.3 t rear counterweight and 36 t carbody counterweight 82.3 t rear counterweight and 36 t carbody counterweight

Load capacities in [t] with 41 m main boom 83° Load capacities in [t] with 50 m main boom 83°
Jib length [m] Jib length [m]
20 32 44 56 68 83 20 32 44 56 68 83
13.8 54.7 14.9 44.2
18 40.4 34.2 20 35.9 30.1
22 29.6 26.4 22.5 22 32.0 27.6 20.2
26 23.0 20.9 18.8 14.3 24 27.8 24.5 19.8
Radius [m]

Radius [m]

28 18.8 16.9 13.9 9.2 26 24.6 22.2 19.0 13.0

34 14.6 13.0 11.6 8.7 5.5 28 21.6 19.6 17.3 12.8
40 10.5 9.2 7.9 5.1 30 17.9 16.0 12.5 8.7
50 7.6 6.7 5.6 4.2 34 15.1 13.4 11.4 8.3 5.0
60 5.0 4.2 3.2 40 10.8 9.3 7.7 4.8
65 3.6 2.7 48 8.4 7.2 6.2 4.3
70 3.0 2.2 55 5.9 5.0 3.7
75 70 3.2 2.3
82.3 t rear counterweight and 36 t carbody counterweight 82.3 t rear counterweight and 36 t carbody counterweight

Load capacities in [t] with 62 m main boom 83°

Jib length [m] TLT 11962152. Above load charts are for reference only. For actual lift duty please refer to
load chart in operator’s cabin or manual. Otherwise we recommend you to plan your lifting job
20 32 44 56 62 65
using Crane Planner 2.0.
16.4 32.2
20 29.7 23.1
24 26.5 21.5 16.2
28 22.8 19.4 15.8 11.3
Radius [m]

30 18.3 15.5 11.2 9.4 8.4

36 14.6 12.9 10.7 8.9 8.1
42 10.6 9.0 8.3 7.7
48 8.8 7.5 6.9 6.5
55 6.1 5.6 5.4
60 5.3 4.9 4.6
65 4.3 4.0
70 3.3 3.5
82.3 t rear counterweight and 36 t carbody counterweight

22 LR 1250.1
Load capacities with luffing jib

Load capacities in [t] with 20 m main boom 75° Load capacities in [t] with 29 m main boom 75°
Jib length [m] Jib length [m]
20 32 44 56 68 83 20 32 44 56 68 83
16.7 44.4 19 45.4
22 28.8 25.5 24 30.6 24.0
28 18.0 16.4 30 19.0 17.3
32 14.9 13.6 11.7 36 14.5 13.1 11.9
Radius [m]

Radius [m]
38 12.0 10.7 9.5 8.1 40 12.5 11.3 10.1 8.5
40 9.9 8.8 7.6 42 10.5 9.3 8.1
44 8.6 7.7 6.6 5.1 46 9.1 8.1 7.0 4.9
50 7.2 6.2 5.2 4.2 55 6.0 5.1 4.1
55 5.4 4.4 3.5 60 5.3 4.3 3.3
60 4.7 3.7 2.8 65 3.7 2.8
65 3.2 2.3 70 3.2 2.3
70 2.7 75 2.7
82.3 t rear counterweight and 36 t carbody counterweight 82.3 t rear counterweight and 36 t carbody counterweight

Load capacities in [t] with 41 m main boom 75° Load capacities in [t] with 50 m main boom 75°
Jib length [m] Jib length [m]
20 32 44 56 68 83 20 32 44 56 68 83
22.1 35.7 24.4 29.6
28 28.1 25.6 30 24.3 22.7
30 25.5 22.9 34 21.2 20.1
32 22.6 20.2 36 18.4 16.5
Radius [m]

Radius [m]

34 18.3 16.5 40 15.4 13.8 11.5

36 16.7 15.0 46 12.4 11.0 9.6 7.7
38 15.2 13.8 12.0 48 10.2 8.8 7.6
44 12.3 11.0 9.7 8.1 55 8.3 7.0 6.1 4.3
50 9.0 7.9 6.8 4.6 60 6.0 5.2 4.0
55 7.8 6.7 5.7 4.3 70 4.3 3.8 2.9
65 5.1 4.1 3.2 75 3.3 2.4
75 3.1 2.1 80 2.8
82.3 t rear counterweight and 36 t carbody counterweight 82.3 t rear counterweight and 36 t carbody counterweight

Load capacities in [t] with 62 m main boom 75°

Jib length [m] TLT 11962152. Above load charts are for reference only. For actual lift duty please refer to
load chart in operator’s cabin or manual. Otherwise we recommend you to plan your lifting job
20 32 44 56 62 65
using Crane Planner 2.0.
27.5 23.2
32 20.0
34 18.9 17.5
38 16.9 15.6 14.4
Radius [m]

42 14.1 13.0
44 13.4 12.3 10.6
46 12.8 11.7 10.5 8.6
48 12.3 11.2 9.7 8.6 7.7
50 10.6 9.1 8.3 7.6
65 5.7 5.3 5.0
75 4.0 3.8
80 3.3
82.3 t rear counterweight and 36 t carbody counterweight

LR 1250.1 23
Load capacities with luffing jib

Load capacities in [t] with 20 m main boom 65° Load capacities in [t] with 32 m main boom 65°
Jib length [m] Jib length [m]
20 32 44 56 68 83 20 32 44 56 68 83
24 31.3 27.9 24.0
26 26.9 36 18.9
30 21.2 18.9 38 17.1
38 13.4 12.1 42 14.4 12.7
Radius [m]

Radius [m]
40 12.5 11.0 44 13.5 12.1
42 11.6 10.3 46 12.6 11.2
44 9.5 8.3 50 9.7 8.6
48 8.4 7.3 55 8.4 7.3
50 8.0 6.9 60 6.2 5.2
60 5.1 4.2 3.0 65 5.4 4.4 3.3
70 3.0 2.1 75 3.3 2.4
75 2.6 80 2.9
82.3 t rear counterweight and 36 t carbody counterweight 82.3 t rear counterweight and 36 t carbody counterweight

Load capacities in [t] with 44 m main boom 65° Load capacities in [t] with 56 m main boom 65°
Jib length [m] Jib length [m]
20 32 44 56 68 83 20 32 44 56 68 83
33 20.2 38.1 14.8
34 19.5 44 12.4
40 16.0 15.4 46 11.7 11.0
46 12.9 48 10.5
Radius [m]

Radius [m]

48 12.2 11.6 55 8.8 8.0

55 9.7 8.5 60 7.1 6.2
65 6.2 5.2 65 6.4 5.5
70 5.5 4.5 3.3 70 4.9 4.0
75 4.8 3.8 2.8 75 4.4 3.5 2.4
80 3.3 2.3 80 3.9 3.1 2.0
85 2.9 85 2.7
90 90 2.4
82.3 t rear counterweight and 36 t carbody counterweight 82.3 t rear counterweight and 36 t carbody counterweight

Load capacities in [t] with 62 m main boom 65°

Jib length [m] TLT 11962152. Above load charts are for reference only. For actual lift duty please refer to
load chart in operator’s cabin or manual. Otherwise we recommend you to plan your lifting job
20 32 44 56 62 65
using Crane Planner 2.0.
40.6 12.3
44 11.3
46 10.8
48 10.2 9.2
Radius [m]

50 8.8
55 7.8 6.8
60 7.0 6.1
65 5.4 4.5 4.1
70 4.9 4.0 3.6 3.3
75 3.5 3.1 2.9
80 3.1 2.7 2.5
85 2.4 2.1
82.3 t rear counterweight and 36 t carbody counterweight

24 LR 1250.1
LR 1250.1 25
Luffing jib 1916.xx
---
Jib lengths 20-95 m
78°
7 3°
Units in m
144
60°

132 12 t
°
50
95

120
92

1080-1770
°

89
40

86
80 3
8
77

108 Auxiliary jib 12 t (option)

74
71
30°

The maximum capacity of the ­

68
65

auxiliary jib is 12 t.
62
59

96
56
53
50
20°

44 7
4

84
38 1
4
1 5°

35
32
29
26

72
23
20

83° 88°
7 5°
60
6 5°
0°

5 5° 59
56
48 53
50
°
45

47
44
41
36
38
35
32
29
24 26
23
20

12
0°

0
108 96 84 72 60 48 36 24 12 0

Jib configuration 1916.xx

Jib section Amount of jib sections
Jib foot 7 m 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Jib section 3 m 1 1 1 1 1 1 1 1 1 1 1 1 1
Jib section 6 m 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Jib section 12 m 1 1 1 1 2 2 2 2 3 3 3 3 4 4 4 4 5 5 5 5 6 6 6 6
Jib head 7 m 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Jib length [m] 20 23 26 29 32 35 38 41 44 47 50 53 56 59 62 65 68 71 74 77 80 83 86 89 92 95
Auxiliary jib ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓
For main boom configuration please refer to the table on page 18.

26 LR 1250.1
Load capacities with luffing jib

Load capacities in [t] with 20 m main boom 88° Load capacities in [t] with 29 m main boom 88°
Jib length [m] Jib length [m]
20 35 50 65 80 95 20 35 50 65 80 95
9 70.7 8.1 70.7
11 70.7 49.6 12 66.1 45.4
12 69.8 48.1 16 49.2 39.2 26.3
16 47.7 40.2 28.5 18 42.3 36.0 25.1 15.2
Radius [m]

Radius [m]
18 39.9 34.6 27.0 16.7 22 32.0 29.9 23.0 14.5 8.7
22 28.4 26.9 23.7 15.4 9.7 24 26.5 21.9 14.0 8.5 4.6
24 23.7 21.3 14.7 9.4 5.3 32 19.2 17.4 12.7 8.2 4.6
32 16.5 15.0 12.8 8.6 5.1 38 14.5 11.6 7.7 4.5
38 12.1 10.6 8.0 4.8 44 12.2 10.4 7.2 4.2
46 9.5 8.0 6.7 4.3 65 6.1 4.9 3.0
55 6.1 5.1 3.5 75 3.7 2.2
75 2.5 80 3.1
82.3 t rear counterweight and 36 t carbody counterweight 82.3 t rear counterweight and 36 t carbody counterweight

Load capacities in [t] with 41 m main boom 88° Load capacities in [t] with 50 m main boom 88°
Jib length [m] Jib length [m]
20 35 50 65 80 95 20 35 50 65 80 95
8.6 61.2 8.9 50.8
12 55.6 38.7 12 46.1 32.0
16 42.4 35.2 23.0 16 37.2 29.7 20.1
18 37.0 32.1 22.4 13.2 20 29.1 25.2 18.8 11.6
Radius [m]

Radius [m]

22 28.8 26.1 20.8 12.8 7.7 22 26.1 23.1 18.3 11.3 6.9
24 23.3 19.5 12.6 7.6 24 20.9 17.3 11.3 6.8
34 16.3 14.4 11.6 7.4 4.0 26 19.1 16.3 11.2 6.8 3.5
40 12.2 10.1 7.0 4.0 40 11.1 9.0 6.6 3.5
50 9.6 7.8 6.0 3.7 50 8.8 6.9 5.5 3.4
55 6.9 5.6 3.3 65 4.8 3.6 2.4
70 3.6 2.3 70 3.1
80 2.6 80 2.2
82.3 t rear counterweight and 36 t carbody counterweight 82.3 t rear counterweight and 36 t carbody counterweight

Load capacities in [t] with 56 m main boom 88°

Jib length [m] TLT 11962152. Above load charts are for reference only. For actual lift duty please refer to
20 35 50 65 71 74 load chart in operator’s cabin or manual. Otherwise we recommend you to plan your lifting job
using Crane Planner 2.0.
9.1 43.1
13 38.8 27.1
16 33.8 25.3 17.4
20 27.0 22.4 16.1 10.6 8.7
Radius [m]

26 17.5 14.3 10.0 8.4 7.6

28 16.3 13.8 9.9 8.3 7.6
36 13.0 11.1 9.3 8.0 7.5
38 12.4 10.5 8.8 8.0 7.4
50 7.9 6.4 5.9 5.6
65 4.4 3.9 3.7
70 3.4 3.2
75 2.7
82.3 t rear counterweight and 36 t carbody counterweight

LR 1250.1 27
Load capacities with luffing jib

Load capacities in [t] with 20 m main boom 83° Load capacities in [t] with 29 m main boom 83°
Jib length [m] Jib length [m]
20 35 50 65 80 95 20 35 50 65 80 95
11.3 70.7 12.4 70.7
16 58.3 42.7 18 51.1 39.5
22 34.0 32.7 25.0 22 39.5 34.3 23.7
26 24.4 22.4 14.6 26 29.9 22.1 14.0
Radius [m]

Radius [m]
30 20.1 20.1 13.9 9.0 30 26.0 21.2 13.5 8.5
32 18.5 18.0 13.5 8.8 36 20.7 19.4 12.7 8.1 4.6
34 17.2 16.2 13.2 8.6 5.1 42 16.4 11.9 7.6 4.5
40 12.9 11.3 8.0 4.8 48 13.5 11.2 7.1 4.1
55 7.0 6.4 3.8 50 12.8 10.7 7.0 4.1
65 5.1 4.4 3.1 60 9.0 6.5 3.4
75 3.1 2.0 65 7.8 6.2 3.2
80 2.4 85 2.0
82.3 t rear counterweight and 36 t carbody counterweight 82.3 t rear counterweight and 36 t carbody counterweight

Load capacities in [t] with 41 m main boom 83° Load capacities in [t] with 50 m main boom 83°
Jib length [m] Jib length [m]
20 35 50 65 80 95 20 35 50 65 80 95
13.8 55.4 14.9 43.9
20 42.5 33.8 20 37.7 28.7
26 29.6 27.9 20.4 24 30.7 26.2 18.5
28 25.7 19.9 12.5 30 21.8 17.9 11.1
Radius [m]

Radius [m]

32 22.2 19.2 12.4 7.5 34 19.0 17.0 11.0 6.8

40 16.9 16.2 11.5 7.3 4.0 38 16.7 15.2 10.8 6.8 3.5
44 14.2 11.0 7.1 4.0 44 13.0 10.2 6.7 3.5
60 8.1 6.1 3.3 55 9.8 8.2 6.1 3.5
65 7.2 5.6 3.1 60 7.2 5.8 3.2
70 6.2 5.2 2.8 70 5.6 4.6 2.7
75 4.7 2.5 75 4.1 2.3
85 3.1 85 2.9
82.3 t rear counterweight and 36 t carbody counterweight 82.3 t rear counterweight and 36 t carbody counterweight

Load capacities in [t] with 56 m main boom 83°

Jib length [m] TLT 11962152. Above load charts are for reference only. For actual lift duty please refer to
20 35 50 65 71 74 load chart in operator’s cabin or manual. Otherwise we recommend you to plan your lifting job
using Crane Planner 2.0.
15.7 37.4
22 31.7 23.9
26 26.4 22.1 16.0
28 24.3 21.0 15.9
Radius [m]

30 19.9 15.6 10.1

32 18.9 15.3 10.1 8.3 7.6
40 14.7 13.0 10.0 8.3 7.6
44 11.7 9.5 8.2 7.6
60 6.7 6.3 6.2
65 6.0 5.5 5.4
75 4.2 4.1
80 3.5
82.3 t rear counterweight and 36 t carbody counterweight

28 LR 1250.1
Load capacities with luffing jib

Load capacities in [t] with 20 m main boom 75° Load capacities in [t] with 29 m main boom 75°
Jib length [m] Jib length [m]
20 35 50 65 80 95 20 35 50 65 80 95
16.7 56.4 19 45.7
24 36.3 34.4 26 32.0 30.8
28 28.5 28 29.2 28.6
30 25.3 22.6 32 24.2 21.5
Radius [m]

Radius [m]
36 18.4 19.4 13.2 36 21.0 20.3
42 12.1 14.8 12.4 8.0 38 19.6 19.0 12.7
44 13.6 12.0 7.9 44 16.3 15.7 12.2
50 10.9 10.9 7.4 4.3 46 14.8 12.0 7.5
55 9.2 8.8 7.0 4.0 55 11.7 11.0 6.9 3.9
60 7.1 6.6 3.7 70 7.6 6.3 3.1
75 3.9 2.7 85 4.8 2.3
85 2.4 2.1 90 2.1
82.3 t rear counterweight and 36 t carbody counterweight 82.3 t rear counterweight and 36 t carbody counterweight

Load capacities in [t] with 41 m main boom 75° Load capacities in [t] with 50 m main boom 75°
Jib length [m] Jib length [m]
20 35 50 65 80 95 20 35 50 65 80 95
22.1 35.2 24.4 29.0
30 25.5 23.9 32 22.2 20.3
32 23.6 22.3 34 20.9 19.0
36 19.8 18.2 38 16.9 15.5
Radius [m]

Radius [m]

42 16.3 15.4 11.8 44 14.5 13.1 10.8

48 13.1 11.4 7.1 48 12.9 11.9 10.5
55 10.9 9.9 6.7 3.7 50 11.3 10.0 6.6
60 9.6 8.9 6.5 3.6 60 9.0 7.8 6.3 3.4
65 7.9 6.3 3.3 65 7.0 5.8 3.2
80 4.8 2.6 75 5.6 4.5 2.8
85 4.2 2.4 85 3.5 2.3
90 3.7 2.2 90 3.0
82.3 t rear counterweight and 36 t carbody counterweight 82.3 t rear counterweight and 36 t carbody counterweight

Load capacities in [t] with 56 m main boom 75°

Jib length [m] TLT 11962152. Above load charts are for reference only. For actual lift duty please refer to
20 35 50 65 71 74 load chart in operator’s cabin or manual. Otherwise we recommend you to plan your lifting job
using Crane Planner 2.0.
26 25.6
34 19.6 17.7
36 18.5 16.7
40 14.9 13.5
Radius [m]

46 12.8 11.6 10.1

48 12.2 11.0 9.6 8.3
55 9.3 8.0 7.5 7.3
60 8.3 7.1 6.6 6.4
65 7.5 6.3 5.8 5.6
70 5.6 5.1 5.0
80 4.5 4.0 3.8
85 3.5 3.4
82.3 t rear counterweight and 36 t carbody counterweight

LR 1250.1 29
Load capacities with luffing jib

Load capacities in [t] with 20 m main boom 65° Load capacities in [t] with 29 m main boom 65°
Jib length [m] Jib length [m]
20 35 50 65 80 95 20 35 50 65 80 95
24 34.8 28 27.3
30 26.5 32 23.2
36 20.6 36 19.4
38 19.3 44 15.0 14.4
Radius [m]

Radius [m]
44 16.0 15.4 48 13.4 12.8
50 13.0 11.8 60 9.4 8.6
55 11.5 10.7 65 7.6 6.5
60 9.4 6.9 70 6.7 6.0 3.2
70 6.6 6.2 3.2 75 6.0 5.3 3.0
75 5.8 2.9 80 4.6 2.8
85 3.8 2.4 90 3.5 2.3
90 2.1 95 2.1
82.3 t rear counterweight and 36 t carbody counterweight 82.3 t rear counterweight and 36 t carbody counterweight

Load capacities in [t] with 41 m main boom 65° Load capacities in [t] with 50 m main boom 65°
Jib length [m] Jib length [m]
20 35 50 65 80 95 20 35 50 65 80 83
31.7 21.3 35.5 16.7
34 19.5 36 16.5
42 14.2 38 15.4
48 11.9 46 11.1
Radius [m]

Radius [m]

50 11.3 10.6 50 10.0

60 8.1 7.2 55 8.8 7.8
65 7.2 6.3 60 6.9
70 5.6 4.5 65 6.2 4.9
75 4.9 3.9 2.7 70 5.5 4.3 3.2
80 4.3 3.4 2.3 75 3.8 2.7 2.4
85 2.9 80 3.3 2.2
95 2.1 85 2.9
82.3 t rear counterweight and 36 t carbody counterweight 82.3 t rear counterweight and 36 t carbody counterweight

Load capacities in [t] with 56 m main boom 65°

Jib length [m] TLT 11962152. Above load charts are for reference only. For actual lift duty please refer to
load chart in operator’s cabin or manual. Otherwise we recommend you to plan your lifting job
20 35 50 65 71 74
using Crane Planner 2.0.
38.1 13.9
40 13.2
42 12.5
46 11.1
Radius [m]

48 9.3
50 8.9
60 7.0 5.9
65 5.2 3.9
70 4.6 3.4 2.9 2.8
75 4.1 2.9 2.4 2.3
80 2.5 2.0
85 2.1
82.3 t rear counterweight and 36 t carbody counterweight

30 LR 1250.1
LR 1250.1 31
Fixed jib 1008.xx
---
Jib lengths 11-26 m
Units in m
108
30° 15°

96 26
23
20
17
84 14
11
80° 86°
70°
72
60°

° 74
60 50 71
68
65
62
°

59
40

48 56
53
50
47
30°

44
36 41
38
35
32
29
24 26
23
20

12
0°

0
108 96 84 72 60 48 36 24 12 0

Jib configuration 1008.xx

Jib section Amount of jib sections
Jib foot 5.5 m 1 1 1 1 1 1
Jib section 3 m 1 1 1
Jib section 6 m 1 1 2 2
Jib head 5.5 m 1 1 1 1 1 1
Jib length [m] 11 14 17 20 23 26
For main boom configuration please refer to the table on page 18.

32 LR 1250.1
Load capacities with fixed jib 15°

Load capacities in [t] with 20 m main boom Load capacities in [t] with 35 m main boom
Jib length [m] Jib length [m]
11 14 20 26 11 14 20 26
9 35.9 7 35.9
10 35.9 34.1 8 35.9 35.9
11 35.9 33.3 27.4 10 35.9 35.3 30.2
12 35.9 32.6 26.4 19.7 13 35.9 33.8 27.4 18.9
Radius [m]

Radius [m]
16 35.8 29.8 23.1 17.3 18 35.9 31.5 24.0 16.5
22 29.9 25.3 18.5 14.3 24 34.1 28.5 20.4 14.3
28 24.0 20.7 14.8 11.7 30 25.1 25.3 17.3 13.0
30 23.4 19.5 13.8 11.1 38 17.8 18.1 14.2 10.8
32 18.3 13.0 10.5 42 15.3 15.6 13.1 10.0
36 12.1 9.4 46 13.4 12.3 9.2
38 11.5 9.0 50 11.8 8.7
44 8.0 55 8.1
82.3 t rear counterweight and 36 t carbody counterweight 82.3 t rear counterweight and 36 t carbody counterweight

Load capacities in [t] with 50 m main boom Load capacities in [t] with 65 m main boom
Jib length [m] Jib length [m]
11 14 20 26 11 14 20 26
6.7 35.9 7.2 35.9
8 35.9 35.4 9 35.9 33.6
11 35.9 34.1 27.5 11 35.9 33.0 25.4
13 35.9 33.3 26.2 18.3 14 35.7 31.8 24.2 17.0
Radius [m]

Radius [m]

18 35.9 31.5 23.3 16.3 20 31.8 28.7 21.6 15.0

24 32.5 28.5 20.8 14.5 28 24.4 24.5 19.4 13.5
30 24.0 24.4 19.0 13.4 44 12.1 12.3 12.9 11.6
38 16.7 17.0 16.2 12.1 55 7.5 7.8 8.2 8.7
50 10.4 10.6 11.1 10.0 65 4.8 5.0 5.4 5.8
55 8.6 8.8 9.3 9.2 70 3.9 4.3 4.6
65 6.4 6.8 75 3.3 3.7
70 5.6 80 2.8
82.3 t rear counterweight and 36 t carbody counterweight 82.3 t rear counterweight and 36 t carbody counterweight

Load capacities in [t] with 74 m main boom

Jib length [m] TLT 11962152. Above load charts are for reference only. For actual lift duty please refer to
load chart in operator’s cabin or manual. Otherwise we recommend you to plan your lifting job
11 14 17
using Crane Planner 2.0.
7.6 35.1
9 34.3 31.1
10 32.8 30.8 27.8
14 30.6 27.4 24.9
Radius [m]

24 26.2 24.1 22.2

32 19.0 19.2 19.4
40 13.4 13.6 13.9
48 9.4 9.7 10.0
50 8.6 8.9 9.2
65 4.0 4.2 4.5
70 2.9 3.2 3.4
75 2.0 2.2 2.4
82.3 t rear counterweight and 36 t carbody counterweight

LR 1250.1 33
Load capacities with fixed jib 30°

Load capacities in [t] with 20 m main boom Load capacities in [t] with 35 m main boom
Jib length [m] Jib length [m]
11 14 20 26 11 14 20 26
11 34.8 8.8 35.9
12 32.7 26.9 11 35.9 29.0
13 31.2 26.1 13 34.3 27.9
14 29.8 24.7 16 30.8 25.6 17.3
Radius [m]

Radius [m]
16 27.1 23.7 16.4 18 28.9 24.0 16.2
18 25.1 21.6 15.1 12.1 20 27.2 23.6 15.4 11.7
20 24.0 20.1 14.0 11.3 28 23.4 19.2 12.7 9.5
22 22.8 18.7 13.0 10.5 36 19.6 16.6 11.2 8.2
30 19.0 15.2 10.7 8.3 44 14.2 14.6 9.9 7.3
32 14.8 10.2 7.9 46 13.5 9.7 7.1
40 9.1 6.8 50 9.5 6.8
46 6.4 55 6.6
82.3 t rear counterweight and 36 t carbody counterweight 82.3 t rear counterweight and 36 t carbody counterweight

Load capacities in [t] with 50 m main boom Load capacities in [t] with 65 m main boom
Jib length [m] Jib length [m]
11 14 20 26 11 14 20 26
9.4 35.9 9.9 32.8
12 35.9 28.0 12 31.9 26.7
14 34.6 27.3 16 29.6 25.0 17.4
16 32.9 25.9 16.9 20 27.5 23.6 16.3 11.7
Radius [m]

Radius [m]

18 31.2 24.8 16.2 30 23.0 20.1 13.8 9.9

20 29.9 24.0 15.5 11.7 42 13.5 13.9 12.1 8.5
36 18.6 18.1 12.1 8.8 55 7.7 8.1 8.7 7.5
44 13.4 13.7 10.7 7.9 60 6.2 6.5 7.1 7.2
55 8.7 9.0 9.5 7.1 65 4.9 5.1 5.7 6.2
60 7.3 7.9 6.8 70 3.7 4.0 4.5 5.0
65 6.5 6.6 75 3.4 3.9
70 5.8 85 2.0
82.3 t rear counterweight and 36 t carbody counterweight 82.3 t rear counterweight and 36 t carbody counterweight

Load capacities in [t] with 74 m main boom

TLT 11962152. Above load charts are for reference only. For actual lift duty please refer to
Jib length [m]
load chart in operator’s cabin or manual. Otherwise we recommend you to plan your lifting job
11 14 17
using Crane Planner 2.0.
10.2 28.8
13 26.0 24.1
14 25.1 24.0 20.4
22 23.5 20.8 18.5
Radius [m]

30 21.1 18.5 16.4

38 15.2 15.5 14.7
46 10.8 11.1 11.5
55 7.1 7.4 7.8
60 5.5 5.8 6.2
65 4.2 4.5 4.8
70 3.1 3.3 3.6
75 2.1 2.3 2.6
82.3 t rear counterweight and 36 t carbody counterweight

34 LR 1250.1
Fixed jib 0806.xx
---
Jib lengths 11-32 m
Units in m
120
30°
15°

108 32
29
26
23
96 20
17
14
11
84 80° 86°

70°

60°
72

° 80
50 77
74
60 71
68
65
°
40

62
59
48 56
53
50
30°

47
44
36 41
38
35
32
29
24 26
23
20

12
0°

0
108 96 84 72 60 48 36 24 12 0

Jib configuration 0806.xx

Jib section Amount of jib sections
Jib foot 5.5 m 1 1 1 1 1 1 1 1
Jib section 3 m 1 1 1 1
Jib section 6 m 1 1 2 2 3 3
Jib head 5.5 m 1 1 1 1 1 1 1 1
Jib length [m] 11 14 17 20 23 26 29 32
For main boom configuration please refer to the table on page 18.

LR 1250.1 35
Load capacities with fixed jib 15°

Load capacities in [t] with 20 m main boom Load capacities in [t] with 35 m main boom
Jib length [m] Jib length [m]
11 17 23 29 32 11 17 23 29 32
11 20.5 8 22.7
13 19.6 12.5 10 22.1 13.6
16 18.4 11.8 9.1 6.5 12 21.4 13.2 9.7
18 17.7 11.3 8.8 6.2 5.1 14 20.9 12.7 9.4 6.7
Radius [m]

Radius [m]
22 16.6 10.5 8.2 5.8 4.6 20 19.2 11.6 8.8 6.1 4.9
26 15.7 9.9 7.7 5.4 4.3 28 17.3 10.5 8.0 5.5 4.3
30 14.6 9.5 7.3 5.0 4.0 36 16.0 9.7 7.4 4.9 3.9
34 8.9 6.9 4.8 3.7 40 15.1 9.4 7.1 4.7 3.7
38 6.5 4.5 3.5 44 9.0 6.9 4.5 3.5
42 6.0 4.3 3.3 50 6.4 4.3 3.3
48 4.1 3.2 55 6.0 4.2 3.2
50 3.1 60 4.1 3.1
82.3 t rear counterweight and 36 t carbody counterweight 82.3 t rear counterweight and 36 t carbody counterweight

Load capacities in [t] with 50 m main boom Load capacities in [t] with 65 m main boom
Jib length [m] Jib length [m]
11 17 23 29 32 11 17 23 29 32
6.7 21.1 7.2 18.6
10 20.5 12.6 10 18.3 11.7
12 20.2 12.3 8.8 13 18.0 11.4 7.9
14 19.7 12.0 8.6 6.1 16 17.7 11.2 7.8 5.4 4.4
Radius [m]

Radius [m]

16 19.3 11.8 8.5 6.0 4.9 24 17.0 10.6 7.4 5.1 4.2
34 17.1 10.1 7.4 5.1 4.0 32 16.4 10.1 7.1 4.9 4.0
46 12.8 9.5 7.0 4.6 3.6 48 10.9 9.4 6.6 4.5 3.6
55 9.3 9.0 6.7 4.3 3.3 65 5.5 6.1 6.4 4.2 3.3
60 8.4 6.4 4.1 3.2 70 5.0 5.5 4.1 3.2
65 6.2 4.1 3.1 80 3.6 4.0 3.1
70 4.0 3.1 85 3.3 3.1
75 3.0 90 2.7
82.3 t rear counterweight and 36 t carbody counterweight 82.3 t rear counterweight and 36 t carbody counterweight

Load capacities in [t] with 80 m main boom

Jib length [m] TLT 11962152. Above load charts are for reference only. For actual lift duty please refer to
load chart in operator’s cabin or manual. Otherwise we recommend you to plan your lifting job
11 14 17 20 23
using Crane Planner 2.0.
7.8 14.9
9 14.9 11.6
11 14.8 11.6 9.0
12 14.7 11.5 9.0 7.6
Radius [m]

20 14.2 11.1 8.7 7.4 6.0

28 13.7 10.8 8.4 7.2 5.9
36 13.3 10.6 8.2 7.1 5.8
44 11.4 10.2 8.1 7.0 5.7
55 7.1 7.4 7.7 6.9 5.5
65 4.3 4.6 4.9 5.2 5.2
70 3.3 3.6 3.8 4.1 4.4
80 2.1 2.3 2.5
82.3 t rear counterweight and 36 t carbody counterweight

36 LR 1250.1
Load capacities with fixed jib 30°

Load capacities in [t] with 20 m main boom Load capacities in [t] with 35 m main boom
Jib length [m] Jib length [m]
11 17 23 29 32 11 17 23 29 32
13 17.6 11 18.9
16 16.8 10.6 14 18.2 11.1
20 16.0 10.1 7.8 18 17.4 10.7 8.1
22 15.5 9.9 7.6 5.3 20 17.0 10.4 7.9
Radius [m]

Radius [m]
24 14.6 9.7 7.4 5.2 4.1 24 16.4 10.1 7.6 5.2 4.1
28 13.3 9.2 7.0 4.9 3.8 34 14.2 9.5 7.0 4.7 3.7
30 12.9 8.8 6.8 4.7 3.7 36 13.8 9.2 6.8 4.6 3.6
32 8.5 6.6 4.6 3.6 42 12.9 8.5 6.4 4.4 3.4
36 8.0 6.1 4.4 3.4 46 8.2 6.0 4.3 3.3
42 5.7 4.2 3.3 55 5.7 4.2 3.2
48 4.1 3.1 60 4.2 3.1
50 3.1 65 3.1
82.3 t rear counterweight and 36 t carbody counterweight 82.3 t rear counterweight and 36 t carbody counterweight

Load capacities in [t] with 50 m main boom Load capacities in [t] with 65 m main boom
Jib length [m] Jib length [m]
11 17 23 29 32 11 17 23 29 32
9.4 18.2 9.9 16.5
14 17.7 10.7 14 16.3 10.2
18 17.3 10.5 7.7 18 16.2 10.1 7.2
20 17.2 10.3 7.6 22 16.2 9.9 7.1 4.9
Radius [m]

Radius [m]

22 17.0 10.2 7.6 5.2 32 16.0 9.6 6.9 4.7 3.8

24 16.8 10.1 7.5 5.1 4.0 42 14.3 9.3 6.8 4.5 3.6
42 14.4 9.3 6.8 4.5 3.4 55 8.5 8.8 6.5 4.3 3.3
55 9.4 8.3 6.0 4.2 3.2 65 5.6 6.3 6.0 4.2 3.2
60 8.1 5.9 4.1 3.2 75 4.1 4.7 4.2 3.2
65 5.7 4.1 3.1 80 3.7 4.2 3.2
70 4.1 3.1 85 3.4 3.2
75 4.1 3.1 90 2.8
82.3 t rear counterweight and 36 t carbody counterweight 82.3 t rear counterweight and 36 t carbody counterweight

Load capacities in [t] with 80 m main boom

Jib length [m] TLT 11962152. Above load charts are for reference only. For actual lift duty please refer to
11 14 17 20 23 load chart in operator’s cabin or manual. Otherwise we recommend you to plan your lifting job
using Crane Planner 2.0.
10.4 13.9
13 13.9 11.2
16 13.8 11.2 8.7 7.6
18 13.8 11.1 8.6 7.6 6.0
Radius [m]

28 13.6 11.0 8.5 7.4 5.9

38 13.4 10.9 8.5 7.3 5.8
44 11.7 10.4 8.5 7.2 5.8
46 10.9 10.1 8.5 7.2 5.8
50 9.3 9.6 8.5 7.1 5.8
55 7.4 7.8 8.2 7.0 5.8
75 2.5 2.8 3.1 3.4 3.7
80 2.2 2.5 2.8
82.3 t rear counterweight and 36 t carbody counterweight

LR 1250.1 37
Fixed jib 0906.21
---
Jib length 7 m
Units in m
96

30°

84
88°
80°
70°
72
60°

° 77
50 74
60 71
68
65
62
°
40

59
48 56
53
50
30°

47
44
36 41
38
35
32
29
24 26
23
20

12
0°

0
96 84 72 60 48 36 24 12 0

The jib length is 7 m, for main boom configuration please refer to

the table on page 18.

38 LR 1250.1
Load capacities with fixed jib 30°

Load capacities in [t] with 20 m main boom Load capacities in [t] with 35 m main boom
Radius [m] Jib length 7 m Radius [m] Jib length 7 m
10 59.2 8 70.7
11 57.6 13 69.3
12 56.2 14 67.0
13 54.7 15 62.1
14 53.6 16 57.8
16 51.6 20 43.7
18 50.0 24 34.0
20 44.3 28 27.4
22 39.0 32 22.6
24 34.6 36 18.9
26 30.9 40 16.0
82.3 t rear counterweight and 36 t carbody counterweight 82.3 t rear counterweight and 36 t carbody counterweight

Load capacities in [t] with 50 m main boom Load capacities in [t] with 65 m main boom
Radius [m] Jib length 7 m Radius [m] Jib length 7 m
7.9 69.1 8.4 48.8
9 68.3 12 46.3
11 65.2 18 40.2
16 52.6 22 33.5
20 41.0 26 27.2
24 33.0 30 22.6
32 21.7 34 18.8
40 15.1 38 15.6
44 12.8 42 13.0
48 10.9 48 9.9
50 10.0 65 4.4
82.3 t rear counterweight and 36 t carbody counterweight 82.3 t rear counterweight and 36 t carbody counterweight

Load capacities in [t] with 77 m main boom

Radius [m] Jib length 7 m TLT 11962152. Above load charts are for reference only. For actual lift duty
please refer to load chart in operator’s cabin or manual. Otherwise we recom-
8.8 34.3
mend you to plan your lifting job using Crane Planner 2.0.
14 32.4
18 30.8
22 28.2
28 22.8
34 17.2
38 14.3
40 13.1
46 10.0
55 6.4
70 2.4
82.3 t rear counterweight and 36 t carbody counterweight

LR 1250.1 39
 Printed in Austria LR 1250.1 1004.03.08 - rA - EN v05.112023 - 13167867

Download datasheet Please contact us.

Änderungen vorbehalten.

Liebherr-Werk Nenzing GmbH · Dr. Hans Liebherr Str. 1 · 6710 Nenzing, Austria
Phone +43 50809 41-473 · [email protected] · www.liebherr.com
facebook.com/LiebherrConstruction