950H Wheel Loader M1G00001-UP (MACHINE) POWERED BY C7 Engine(SEB...

Página 1 de 7

Cerrar SIS

Pantalla anterior

Producto: WHEEL LOADER

Modelo: 950H WHEEL LOADER M1G
Configuración: 950H Wheel Loader M1G00001-UP (MACHINE) POWERED BY
C7 Engine

Localización y Solución de Problemas

C7 Engine for Caterpillar Built Machines
Número de medio -RENR9319-00 Fecha de publicación -01/10/2005 Fecha de actualización -27/10/2005

i02691195

Electronic Service Tools

SMCS - 0785

Caterpillar electronic service tools are designed to help the service technician perform the following
tasks:

Information access

System diagnostics

System calibrations

System configurations

Data link communications

Required Service Tools

The tools that are listed in Table 1 are required in order to enable a service technician to perform the
test procedures that are found in this manual.

Table 1

Required Service Tools

Part Number Description
N/A 4 mm Allen Wrench
6V-2197 Transducer
7X-1171 Transducer Adapter
7X-1695 Cable As
146-4080 Digital Multimeter Gp (RS232)

https://efsa10/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe... 04/10/2007
950H Wheel Loader M1G00001-UP (MACHINE) POWERED BY C7 Engine(SEB... Página 2 de 7

7X-1710 Multimeter Probes

7X-6370 Adapter Cable As (3-PIN BREAKOUT)
208-0059 Adapter Cable As (70-PIN BREAKOUT)
257-8718 Adapter Cable As (120-PIN BREAKOUT)
167-9225 Harness (SERVICE TOOL ADAPTER)
1U-5804 Crimp Tool (12−AWG TO 18−AWG)
175-3700 Connector Repair Kit (DEUTSCH DT)

Two short jumper wires are needed to check the continuity of some wiring harness circuits by
shorting two adjacent terminals together in a connector. A long extension wire may also be needed to
check the continuity of some wiring harness circuits.

Optional Service Tools

Table 2 lists the optional service tools that may be needed during testing or repair.

Table 2

Optional Service Tools

Part Number Description
198-4240 Digital Pressure Indicator
or
1U-5470 Engine Pressure Group
4C-4075 Crimp Tool (4−AWG TO 10−AWG)
4C-4911 (1) Battery Load Tester
5P-7277 Voltage Tester
6V-9130 (2) Temperature Adapter (MULTIMETER)
8T-5319 Connector Tool Group
155-5176 AC/DC Current Probe
(1) Refer to Special Instructions, SEHS9249, "Use of 4C-4911 Battery Load Tester for 6, 8, and 12 Volt Lead Acid
Batteries" and Special Instructions, SEHS7633, "Battery Test Procedure".
(2) Refer to Special Instructions, SEHS8382, "Use of the 6V-9130 Temperature Adapter Group".

Caterpillar Electronic Technician (ET)

Cat ET can display the following information:

Parameters

Event codes

https://efsa10/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe... 04/10/2007
950H Wheel Loader M1G00001-UP (MACHINE) POWERED BY C7 Engine(SEB... Página 3 de 7

Diagnostic codes

Engine configuration

Cat ET can be used by the technician to perform the following functions:

Diagnostic tests

Calibrations

Flash programming

Configuration of the Electronic Control Module (ECM)

Table 3 lists the software that is required in order to use Cat ET. Always use the latest version of Cat
ET that is available.

Table 3

Software Requirements for Cat ET

Part Number Description
JERD2124 Single user license for Cat ET
JERD2129 Data subscription for all engines and machines

Note: For more information regarding the use of Cat ET and the PC requirements for Cat ET, refer
to the documentation that accompanies your Cat ET software.

Connecting Cat ET

Connecting with the Communication Adapter II

Table 4 lists the standard hardware that is required in order to connect Cat ET.

Table 4

Standard Hardware for the Use of Cat ET

Part Number Description
N/A Personal Computer (PC)
275-5120 (1) Communication Adapter Gp (CAT ET TO ECM INTERFACE)
237-7547 (2) Adapter Cable As
225-5985 (3) Parallel Port Cable (COMMUNICATION ADAPTER)
(1) The 7X-1700 Communication Adapter Gp may also be used.
(2) The 237-7547 Adapter Cable As is required to connect to the Universal Serial Bus (USB) on computers that are not
equipped with a RS232 serial port.
(3) The 225-5985 Parallel Port Cable is required to connect to the parallel port.

https://efsa10/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe... 04/10/2007
950H Wheel Loader M1G00001-UP (MACHINE) POWERED BY C7 Engine(SEB... Página 4 de 7

Illustration 1 g01255306
Connecting the Communication Adapter II

(1) Personal Computer (PC)

(2) 237-7547 Adapter Cable As

(3) 196-0055 Adapter Cable As

(4) 225-5985 Parallel Port Cable (COMMUNICATION ADAPTER)

(5) 275-5121 Communication Adapter As

(6) 207-6845 Adapter Cable As

Note: Items (3), (5), and (6) are part of the 275-5120 Communication Adapter Gp .

Use the following procedure in order to connect Cat ET and the Communication Adapter II.

1. Remove the electrical power from the ECM.

2. Connect communications adapter (5) to a communications port on the PC by using one of the
following methods:

a. Connect cable (4) between the "COMPUTER" end of communications adapter (5) and

https://efsa10/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe... 04/10/2007
950H Wheel Loader M1G00001-UP (MACHINE) POWERED BY C7 Engine(SEB... Página 5 de 7

the parallel port of PC (1). Be sure to configure Cat ET for the parallel port. This
configuration provides the fastest connection.

b. Connect cable (3) between the "COMPUTER" end of communication adapter (5) and
the RS232 serial port of PC (1) .

c. Connect cables (2) and (3) between the "COMPUTER" end of communication adapter
(5) and the USB port of PC (1) .

3. Connect cable (6) to communication adapter (5) .

4. Connect cable (6) to a service tool connector.

5. Verify that the "POWER" indicator on the communication adapter is illuminated.

6. Establish communication between Cat ET and the ECM.

7. If Cat ET and the communication adapter do not communicate with the ECM, refer to
troubleshooting without a diagnostic code Troubleshooting, "Electronic Service Tool Will Not
Communicate with ECM".

Communicating with the Wireless Communication Adapter

Table 5 lists the optional hardware that is needed in order to connect Cat ET by using a wireless
connection.

Table 5

Optional Hardware for the Use of Cat ET

Part Number Description
N/A Personal Computer (PC)
261-3363 (1) Wireless Communication Adapter Gp
(1) Refer to Tool Operating Manual, "Using the 261-3363 Wireless Communication Adapter Gp " for information that
is related to the installation and the configuration.

https://efsa10/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe... 04/10/2007
950H Wheel Loader M1G00001-UP (MACHINE) POWERED BY C7 Engine(SEB... Página 6 de 7

Illustration 2 g01297379
(1) Personal computer (PC)

(7) 261-4867 Card (PCMCIA)

(8) 239-9955 Communication Radio Gp

(9) 259-3183 Data Link Cable As

Note: Items (7), (8), and (9) are part of the 261-3363 Wireless Communication Adapter Gp .

Use the following procedure in order to connect the wireless communication adapter for use with Cat
ET.

1. Remove the electrical power from the ECM.

2. Ensure that the computer has been correctly configured for the 261-4867 Card (PCMCIA).
Verify that the PC card is installed in the computer's PCI expansion slot.

3. Connect cable (9) between communication radio (8) and the service tool connector.

4. Restore the electrical power to the ECM. If Cat ET and the communication radio do not
communicate with the ECM, refer to troubleshooting without a diagnostic code
Troubleshooting, "Electronic Service Tool Will Not Communicate with ECM".

https://efsa10/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe... 04/10/2007
950H Wheel Loader M1G00001-UP (MACHINE) POWERED BY C7 Engine(SEB... Página 7 de 7

Copyright 1993 - 2007 Caterpillar Inc. Thu Oct 4 10:47:32 EST 2007
Todos los derechos reservados.
Red privada para licenciados del SIS.

https://efsa10/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe... 04/10/2007